| Age | Commit message (Collapse) | Author |
|---|
|
When memcpy_to_msg() fails in virtio_transport_seqpacket_do_dequeue(),
we already set `dequeued_len` with the negative error value returned
by memcpy_to_msg().
So we can directly check `dequeued_len` value instead of using a
dedicated flag variable to skip the copy path for the rest of
fragments.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vsock_wait_data() is used only by STREAM and SEQPACKET sockets,
so let's rename it to vsock_connectible_wait_data(), using the same
nomenclature (connectible) used in other functions after the
introduction of SEQPACKET.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
vsock_has_data() is used only by STREAM and SEQPACKET sockets,
so let's rename it to vsock_connectible_has_data(), using the same
nomenclature (connectible) used in other functions after the
introduction of SEQPACKET.
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The continue statement at the end of a for-loop has no effect,
invert the if expression and remove the continue.
Addresses-Coverity: ("Continue has no effect")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify the label out_err to out to avoid the meanless kfree.
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently UDP tunnel devices on top of VLANs lose the ability
to offload UDP GSO. Widen the pass thru features from TSO
to all GSO_SOFTWARE.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added a new sysctl, named checksum_enabled, to control
whether DSS checksum can be enabled.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added the mib for the data checksum, MPTCP_MIB_DATACSUMERR.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the MPTCP-level checksum is enabled, on re-injections we
must spool a complete DSS, or the receive side will not be
able to compute the csum and process any data.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added three new members named data_csum, csum_len and
map_csum in struct mptcp_subflow_context, implemented a new function
named mptcp_validate_data_checksum().
If the current mapping is valid and csum is enabled traverse the later
pending skbs and compute csum incrementally till the whole mapping has
been covered. If not enough data is available in the rx queue, return
MAPPING_EMPTY - that is, no data.
Next subflow_data_ready invocation will trigger again csum computation.
When the full DSS is available, validate the csum and return to the
caller an appropriate error code, to trigger subflow reset of fallback
as required by the RFC.
Additionally:
- if the csum prevence in the DSS don't match the negotiated value e.g.
csum present, but not requested, return invalid mapping to trigger
subflow reset.
- keep some csum state, to avoid re-compute the csum on the same data
when multiple rx queue traversal are required.
- clean-up the uncompleted mapping from the receive queue on close, to
allow proper subflow disposal
Co-developed-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In mptcp_parse_option, adjust the expected_opsize, and always parse the
data checksum value from the receiving DSS regardless of csum presence.
Then save it in mp_opt->csum.
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added a new member named csum in struct mptcp_options_received.
When parsing the MP_CAPABLE with data, if the checksum is enabled,
adjust the expected_opsize. If the receiving option length matches the
length with the data checksum, get the checksum value and save it in
mp_opt->csum. And in mptcp_incoming_options, pass it to mpext->csum.
We always parse any csum/nocsum combination and delay the presence check
to later code, to allow reset if missing.
Additionally, in the TX path, use the newly introduce ext field to avoid
MPTCP csum recomputation on TCP retransmission and unneeded csum update
on when setting the data fin_flag.
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added a new flag csum_reqd in struct mptcp_options_received, if
the flag MPTCP_CAP_CHECKSUM_REQD is set in the receiving MP_CAPABLE
suboption, set this flag.
In mptcp_sk_clone and subflow_finish_connect, if the csum_reqd flag is set,
enable the msk->csum_enabled flag.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added a new parameter name sk in mptcp_get_options().
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In mptcp_write_options, if the checksum is enabled, adjust the option
length and send out the data checksum with DSS suboption.
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the checksum is enabled, send out the data checksum with the
MP_CAPABLE suboption with data.
In mptcp_established_options_mp, save the data checksum in
opts->ext_copy.csum. In mptcp_write_options, adjust the option length and
send it out with the MP_CAPABLE suboption.
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added a new member csum_reqd in struct mptcp_out_options and
struct mptcp_subflow_request_sock. Initialized it with the helper
function mptcp_is_checksum_enabled().
In mptcp_write_options, if this field is enabled, send out the MP_CAPABLE
suboption with the MPTCP_CAP_CHECKSUM_REQD flag.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added a new member named csum in struct mptcp_ext, implemented
a new function named mptcp_generate_data_checksum().
Generate the data checksum in mptcp_sendmsg_frag, save it in mpext->csum.
Note that we must generate the csum for zero window probe, too.
Do the csum update incrementally, to avoid multiple csum computation
when the data is appended to existing skb.
Note that in a later patch we will skip unneeded csum related operation.
Changes not included here to keep the delta small.
Co-developed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added a new member named csum_enabled in struct mptcp_sock,
used a dummy mptcp_is_checksum_enabled() helper to initialize it.
Also added a new member named mptcpi_csum_enabled in struct mptcp_info
to expose the csum_enabled flag.
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IETF RFC 8986 [1] includes the definition of SRv6 End.DT4, End.DT6, and
End.DT46 Behaviors.
The current SRv6 code in the Linux kernel only implements End.DT4 and
End.DT6 which can be used respectively to support IPv4-in-IPv6 and
IPv6-in-IPv6 VPNs. With End.DT4 and End.DT6 it is not possible to create a
single SRv6 VPN tunnel to carry both IPv4 and IPv6 traffic.
The proposed End.DT46 implementation is meant to support the decapsulation
of IPv4 and IPv6 traffic coming from a single SRv6 tunnel.
The implementation of the SRv6 End.DT46 Behavior in the Linux kernel
greatly simplifies the setup and operations of SRv6 VPNs.
The SRv6 End.DT46 Behavior leverages the infrastructure of SRv6 End.DT{4,6}
Behaviors implemented so far, because it makes use of a VRF device in
order to force the routing lookup into the associated routing table.
To make the End.DT46 work properly, it must be guaranteed that the routing
table used for routing lookup operations is bound to one and only one VRF
during the tunnel creation. Such constraint has to be enforced by enabling
the VRF strict_mode sysctl parameter, i.e.:
$ sysctl -wq net.vrf.strict_mode=1
Note that the same approach is used for the SRv6 End.DT4 Behavior and for
the End.DT6 Behavior in VRF mode.
The command used to instantiate an SRv6 End.DT46 Behavior is
straightforward, i.e.:
$ ip -6 route add 2001:db8::1 encap seg6local action End.DT46 vrftable 100 dev vrf100.
[1] https://www.rfc-editor.org/rfc/rfc8986.html#name-enddt46-decapsulation-and-s
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Performance and impact of SRv6 End.DT46 Behavior on the SRv6 Networking
=======================================================================
This patch aims to add the SRv6 End.DT46 Behavior with minimal impact on
the performance of SRv6 End.DT4 and End.DT6 Behaviors.
In order to verify this, we tested the performance of the newly introduced
SRv6 End.DT46 Behavior and compared it with the performance of SRv6
End.DT{4,6} Behaviors, considering both the patched kernel and the kernel
before applying the End.DT46 patch (referred to as vanilla kernel).
In details, the following decapsulation scenarios were considered:
1.a) IPv6 traffic in SRv6 End.DT46 Behavior on patched kernel;
1.b) IPv4 traffic in SRv6 End.DT46 Behavior on patched kernel;
2.a) SRv6 End.DT6 Behavior (VRF mode) on patched kernel;
2.b) SRv6 End.DT4 Behavior on patched kernel;
3.a) SRv6 End.DT6 Behavior (VRF mode) on vanilla kernel (without the
End.DT46 patch);
3.b) SRv6 End.DT4 Behavior on vanilla kernel (without the End.DT46 patch).
All tests were performed on a testbed deployed on the CloudLab [2]
facilities. We considered IPv{4,6} traffic handled by a single core (at 2.4
GHz on a Xeon(R) CPU E5-2630 v3) on kernel 5.13-rc1 using packets of size
~ 100 bytes.
Scenario (1.a): average 684.70 kpps; std. dev. 0.7 kpps;
Scenario (1.b): average 711.69 kpps; std. dev. 1.2 kpps;
Scenario (2.a): average 690.70 kpps; std. dev. 1.2 kpps;
Scenario (2.b): average 722.22 kpps; std. dev. 1.7 kpps;
Scenario (3.a): average 690.02 kpps; std. dev. 2.6 kpps;
Scenario (3.b): average 721.91 kpps; std. dev. 1.2 kpps;
Considering the results for the patched kernel (1.a, 1.b, 2.a, 2.b) we
observe that the performance degradation incurred in using End.DT46 rather
than End.DT6 and End.DT4 respectively for IPv6 and IPv4 traffic is minimal,
around 0.9% and 1.5%. Such very minimal performance degradation is the
price to be paid if one prefers to use a single tunnel capable of handling
both types of traffic (IPv4 and IPv6).
Comparing the results for End.DT4 and End.DT6 under the patched and the
vanilla kernel (2.a, 2.b, 3.a, 3.b) we observe that the introduction of the
End.DT46 patch has no impact on the performance of End.DT4 and End.DT6.
[2] https://www.cloudlab.us
Signed-off-by: Andrea Mayer <andrea.mayer@uniroma2.it>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-06-17
The following pull-request contains BPF updates for your *net-next* tree.
We've added 50 non-merge commits during the last 25 day(s) which contain
a total of 148 files changed, 4779 insertions(+), 1248 deletions(-).
The main changes are:
1) BPF infrastructure to migrate TCP child sockets from a listener to another
in the same reuseport group/map, from Kuniyuki Iwashima.
2) Add a provably sound, faster and more precise algorithm for tnum_mul() as
noted in https://arxiv.org/abs/2105.05398, from Harishankar Vishwanathan.
3) Streamline error reporting changes in libbpf as planned out in the
'libbpf: the road to v1.0' effort, from Andrii Nakryiko.
4) Add broadcast support to xdp_redirect_map(), from Hangbin Liu.
5) Extends bpf_map_lookup_and_delete_elem() functionality to 4 more map
types, that is, {LRU_,PERCPU_,LRU_PERCPU_,}HASH, from Denis Salopek.
6) Support new LLVM relocations in libbpf to make them more linker friendly,
also add a doc to describe the BPF backend relocations, from Yonghong Song.
7) Silence long standing KUBSAN complaints on register-based shifts in
interpreter, from Daniel Borkmann and Eric Biggers.
8) Add dummy PT_REGS macros in libbpf to fail BPF program compilation when
target arch cannot be determined, from Lorenz Bauer.
9) Extend AF_XDP to support large umems with 1M+ pages, from Magnus Karlsson.
10) Fix two minor libbpf tc BPF API issues, from Kumar Kartikeya Dwivedi.
11) Move libbpf BPF_SEQ_PRINTF/BPF_SNPRINTF macros that can be used by BPF
programs to bpf_helpers.h header, from Florent Revest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When nla_put_u32() fails, 'ret' could be 0, it should
return error code in tcf_del_walker().
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the gathered SMC statistics network namespace aware, for each
namespace collect an own set of statistic information.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to collect more detailed SMC fallback reason statistics and
provide these statistics to user space on the netlink interface.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the netlink function which collects the statistics information and
delivers it to the userspace.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the ability to collect SMC statistics information. Per-cpu
variables are used to collect the statistic information for better
performance and for reducing concurrency pitfalls. The code that is
collecting statistic data is implemented in macros to increase code
reuse and readability.
Signed-off-by: Guvenc Gulce <guvenc@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't check the sequence number when deciding when to update time_in in
the node table if tag removal is offloaded since the sequence number is
part of the tag. This fixes a problem where the times in the node table
wouldn't update when 0 appeared to be before or equal to seq_out when
tag removal was offloaded.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There has been a few errors in the ethtool reply size calculations,
most of those are hard to trigger during basic testing because of
skb size rounding up and netdev names being shorter than max.
Add a more precise check.
This change will affect the value of payload length displayed in
case of -EMSGSIZE but that should be okay, "payload length" isn't
a well defined term here.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Timewait sockets have included mark since approx 4.18.
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jon Maxwell <jmaxwell37@gmail.com>
Fixes: 00483690552c ("tcp: Add mark for TIMEWAIT sockets")
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hulk Robot reported memory leak in netlbl_mgmt_add_common.
The problem is non-freed map in case of netlbl_domhsh_add() failed.
BUG: memory leak
unreferenced object 0xffff888100ab7080 (size 96):
comm "syz-executor537", pid 360, jiffies 4294862456 (age 22.678s)
hex dump (first 32 bytes):
05 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
fe 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 ................
backtrace:
[<0000000008b40026>] netlbl_mgmt_add_common.isra.0+0xb2a/0x1b40
[<000000003be10950>] netlbl_mgmt_add+0x271/0x3c0
[<00000000c70487ed>] genl_family_rcv_msg_doit.isra.0+0x20e/0x320
[<000000001f2ff614>] genl_rcv_msg+0x2bf/0x4f0
[<0000000089045792>] netlink_rcv_skb+0x134/0x3d0
[<0000000020e96fdd>] genl_rcv+0x24/0x40
[<0000000042810c66>] netlink_unicast+0x4a0/0x6a0
[<000000002e1659f0>] netlink_sendmsg+0x789/0xc70
[<000000006e43415f>] sock_sendmsg+0x139/0x170
[<00000000680a73d7>] ____sys_sendmsg+0x658/0x7d0
[<0000000065cbb8af>] ___sys_sendmsg+0xf8/0x170
[<0000000019932b6c>] __sys_sendmsg+0xd3/0x190
[<00000000643ac172>] do_syscall_64+0x37/0x90
[<000000009b79d6dc>] entry_SYSCALL_64_after_hwframe+0x44/0xae
Fixes: 63c416887437 ("netlabel: Add network address selectors to the NetLabel/LSM domain mapping")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Liu Shixin <liushixin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The following flower filters fail to match packets:
tc filter add dev eth0 ingress protocol 0x8864 flower \
action simple sdata hi64
tc filter add dev eth0 ingress protocol 802.1q flower \
vlan_ethtype 0x8864 action simple sdata "hi vlan"
The protocol 0x8864 (ETH_P_PPP_SES) is a tunnel protocol. As such, it is
being dissected by __skb_flow_dissect and it's internal protocol is
being set as key->basic.n_proto. IOW, the existence of ETH_P_PPP_SES
tunnel is transparent to the callers of __skb_flow_dissect.
OTOH, in the filters above, cls_flower configures its key->basic.n_proto
to the ETH_P_PPP_SES value configured by the user. Matching on this key
fails because of __skb_flow_dissect "transparency" mentioned above.
In the following, I would argue that the problem lies with cls_flower,
unnessary attempting key->basic.n_proto match.
There are 3 close places in fl_set_key in cls_flower setting up
mask->basic.n_proto. They are (in reverse order of appearance in the
code) due to:
(a) No vlan is given: use TCA_FLOWER_KEY_ETH_TYPE parameter
(b) One vlan tag is given: use TCA_FLOWER_KEY_VLAN_ETH_TYPE
(c) Two vlans are given: use TCA_FLOWER_KEY_CVLAN_ETH_TYPE
The match in case (a) is unneeded because flower has no its own
eth_type parameter. It was removed by Jamal Hadi Salim in commit
488b41d020fb06428b90289f70a41210718f52b7 in iproute2. For
TCA_FLOWER_KEY_ETH_TYPE the userspace uses the generic tc filter
protocol field. Therefore the match for the case (a) is done by tc
itself.
The matches in cases (b), (c) are unneeded because the protocol will
appear in and will be matched by flow_dissector_key_vlan.vlan_tpid.
Therefore in the best case, key->basic.n_proto will try to repeat vlan
key match again.
The below patch removes mask->basic.n_proto setting and resets it to 0
in case (c).
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces a new bpf_attach_type for BPF_PROG_TYPE_SK_REUSEPORT
to check if the attached eBPF program is capable of migrating sockets. When
the eBPF program is attached, we run it for socket migration if the
expected_attach_type is BPF_SK_REUSEPORT_SELECT_OR_MIGRATE or
net.ipv4.tcp_migrate_req is enabled.
Currently, the expected_attach_type is not enforced for the
BPF_PROG_TYPE_SK_REUSEPORT type of program. Thus, this commit follows the
earlier idea in the commit aac3fc320d94 ("bpf: Post-hooks for sys_bind") to
fix up the zero expected_attach_type in bpf_prog_load_fixup_attach_type().
Moreover, this patch adds a new field (migrating_sk) to sk_reuseport_md to
select a new listener based on the child socket. migrating_sk varies
depending on if it is migrating a request in the accept queue or during
3WHS.
- accept_queue : sock (ESTABLISHED/SYN_RECV)
- 3WHS : request_sock (NEW_SYN_RECV)
In the eBPF program, we can select a new listener by
BPF_FUNC_sk_select_reuseport(). Also, we can cancel migration by returning
SK_DROP. This feature is useful when listeners have different settings at
the socket API level or when we want to free resources as soon as possible.
- SK_PASS with selected_sk, select it as a new listener
- SK_PASS with selected_sk NULL, fallbacks to the random selection
- SK_DROP, cancel the migration.
There is a noteworthy point. We select a listening socket in three places,
but we do not have struct skb at closing a listener or retransmitting a
SYN+ACK. On the other hand, some helper functions do not expect skb is NULL
(e.g. skb_header_pointer() in BPF_FUNC_skb_load_bytes(), skb_tail_pointer()
in BPF_FUNC_skb_load_bytes_relative()). So we allocate an empty skb
temporarily before running the eBPF program.
Suggested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/netdev/20201123003828.xjpjdtk4ygl6tg6h@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/netdev/20201203042402.6cskdlit5f3mw4ru@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/netdev/20201209030903.hhow5r53l6fmozjn@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/bpf/20210612123224.12525-10-kuniyu@amazon.co.jp
|
|
We will call sock_reuseport.prog for socket migration in the next commit,
so the eBPF program has to know which listener is closing to select a new
listener.
We can currently get a unique ID of each listener in the userspace by
calling bpf_map_lookup_elem() for BPF_MAP_TYPE_REUSEPORT_SOCKARRAY map.
This patch makes the pointer of sk available in sk_reuseport_md so that we
can get the ID by BPF_FUNC_get_socket_cookie() in the eBPF program.
Suggested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/netdev/20201119001154.kapwihc2plp4f7zc@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/bpf/20210612123224.12525-9-kuniyu@amazon.co.jp
|
|
This patch also changes the code to call reuseport_migrate_sock() and
inet_reqsk_clone(), but unlike the other cases, we do not call
inet_reqsk_clone() right after reuseport_migrate_sock().
Currently, in the receive path for TCP_NEW_SYN_RECV sockets, its listener
has three kinds of refcnt:
(A) for listener itself
(B) carried by reuqest_sock
(C) sock_hold() in tcp_v[46]_rcv()
While processing the req, (A) may disappear by close(listener). Also, (B)
can disappear by accept(listener) once we put the req into the accept
queue. So, we have to hold another refcnt (C) for the listener to prevent
use-after-free.
For socket migration, we call reuseport_migrate_sock() to select a listener
with (A) and to increment the new listener's refcnt in tcp_v[46]_rcv().
This refcnt corresponds to (C) and is cleaned up later in tcp_v[46]_rcv().
Thus we have to take another refcnt (B) for the newly cloned request_sock.
In inet_csk_complete_hashdance(), we hold the count (B), clone the req, and
try to put the new req into the accept queue. By migrating req after
winning the "own_req" race, we can avoid such a worst situation:
CPU 1 looks up req1
CPU 2 looks up req1, unhashes it, then CPU 1 loses the race
CPU 3 looks up req2, unhashes it, then CPU 2 loses the race
...
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210612123224.12525-8-kuniyu@amazon.co.jp
|
|
As with the preceding patch, this patch changes reqsk_timer_handler() to
call reuseport_migrate_sock() and inet_reqsk_clone() to migrate in-flight
requests at retransmitting SYN+ACKs. If we can select a new listener and
clone the request, we resume setting the SYN+ACK timer for the new req. If
we can set the timer, we call inet_ehash_insert() to unhash the old req and
put the new req into ehash.
The noteworthy point here is that by unhashing the old req, another CPU
processing it may lose the "own_req" race in tcp_v[46]_syn_recv_sock() and
drop the final ACK packet. However, the new timer will recover this
situation.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210612123224.12525-7-kuniyu@amazon.co.jp
|
|
When we call close() or shutdown() for listening sockets, each child socket
in the accept queue are freed at inet_csk_listen_stop(). If we can get a
new listener by reuseport_migrate_sock() and clone the request by
inet_reqsk_clone(), we try to add it into the new listener's accept queue
by inet_csk_reqsk_queue_add(). If it fails, we have to call __reqsk_free()
to call sock_put() for its listener and free the cloned request.
After putting the full socket into ehash, tcp_v[46]_syn_recv_sock() sets
NULL to ireq_opt/pktopts in struct inet_request_sock, but ipv6_opt can be
non-NULL. So, we have to set NULL to ipv6_opt of the old request to avoid
double free.
Note that we do not update req->rsk_listener and instead clone the req to
migrate because another path may reference the original request. If we
protected it by RCU, we would need to add rcu_read_lock() in many places.
Suggested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/netdev/20201209030903.hhow5r53l6fmozjn@kafai-mbp.dhcp.thefacebook.com/
Link: https://lore.kernel.org/bpf/20210612123224.12525-6-kuniyu@amazon.co.jp
|
|
reuseport_migrate_sock() does the same check done in
reuseport_listen_stop_sock(). If the reuseport group is capable of
migration, reuseport_migrate_sock() selects a new listener by the child
socket hash and increments the listener's sk_refcnt beforehand. Thus, if we
fail in the migration, we have to decrement it later.
We will support migration by eBPF in the later commits.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/bpf/20210612123224.12525-5-kuniyu@amazon.co.jp
|
|
When we close a listening socket, to migrate its connections to another
listener in the same reuseport group, we have to handle two kinds of child
sockets. One is that a listening socket has a reference to, and the other
is not.
The former is the TCP_ESTABLISHED/TCP_SYN_RECV sockets, and they are in the
accept queue of their listening socket. So we can pop them out and push
them into another listener's queue at close() or shutdown() syscalls. On
the other hand, the latter, the TCP_NEW_SYN_RECV socket is during the
three-way handshake and not in the accept queue. Thus, we cannot access
such sockets at close() or shutdown() syscalls. Accordingly, we have to
migrate immature sockets after their listening socket has been closed.
Currently, if their listening socket has been closed, TCP_NEW_SYN_RECV
sockets are freed at receiving the final ACK or retransmitting SYN+ACKs. At
that time, if we could select a new listener from the same reuseport group,
no connection would be aborted. However, we cannot do that because
reuseport_detach_sock() sets NULL to sk_reuseport_cb and forbids access to
the reuseport group from closed sockets.
This patch allows TCP_CLOSE sockets to remain in the reuseport group and
access it while any child socket references them. The point is that
reuseport_detach_sock() was called twice from inet_unhash() and
sk_destruct(). This patch replaces the first reuseport_detach_sock() with
reuseport_stop_listen_sock(), which checks if the reuseport group is
capable of migration. If capable, it decrements num_socks, moves the socket
backwards in socks[] and increments num_closed_socks. When all connections
are migrated, sk_destruct() calls reuseport_detach_sock() to remove the
socket from socks[], decrement num_closed_socks, and set NULL to
sk_reuseport_cb.
By this change, closed or shutdowned sockets can keep sk_reuseport_cb.
Consequently, calling listen() after shutdown() can cause EADDRINUSE or
EBUSY in inet_csk_bind_conflict() or reuseport_add_sock() which expects
such sockets not to have the reuseport group. Therefore, this patch also
loosens such validation rules so that a socket can listen again if it has a
reuseport group with num_closed_socks more than 0.
When such sockets listen again, we handle them in reuseport_resurrect(). If
there is an existing reuseport group (reuseport_add_sock() path), we move
the socket from the old group to the new one and free the old one if
necessary. If there is no existing group (reuseport_alloc() path), we
allocate a new reuseport group, detach sk from the old one, and free it if
necessary, not to break the current shutdown behaviour:
- we cannot carry over the eBPF prog of shutdowned sockets
- we cannot attach/detach an eBPF prog to/from listening sockets via
shutdowned sockets
Note that when the number of sockets gets over U16_MAX, we try to detach a
closed socket randomly to make room for the new listening socket in
reuseport_grow().
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/bpf/20210612123224.12525-4-kuniyu@amazon.co.jp
|
|
As noted in the following commit, a closed listener has to hold the
reference to the reuseport group for socket migration. This patch adds a
field (num_closed_socks) to struct sock_reuseport to manage closed sockets
within the same reuseport group. Moreover, this and the following commits
introduce some helper functions to split socks[] into two sections and keep
TCP_LISTEN and TCP_CLOSE sockets in each section. Like a double-ended
queue, we will place TCP_LISTEN sockets from the front and TCP_CLOSE
sockets from the end.
TCP_LISTEN----------> <-------TCP_CLOSE
+---+---+ --- +---+ --- +---+ --- +---+
| 0 | 1 | ... | i | ... | j | ... | k |
+---+---+ --- +---+ --- +---+ --- +---+
i = num_socks - 1
j = max_socks - num_closed_socks
k = max_socks - 1
This patch also extends reuseport_add_sock() and reuseport_grow() to
support num_closed_socks.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210612123224.12525-3-kuniyu@amazon.co.jp
|
|
This commit adds a new sysctl option: net.ipv4.tcp_migrate_req. If this
option is enabled or eBPF program is attached, we will be able to migrate
child sockets from a listener to another in the same reuseport group after
close() or shutdown() syscalls.
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.co.jp>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Benjamin Herrenschmidt <benh@amazon.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/20210612123224.12525-2-kuniyu@amazon.co.jp
|
|
After the blamed patch, __skb_flow_dissect() on the DSA master stopped
adjusting for the length of the DSA headers. This is because it was told
to adjust only if the needed_headroom is zero, aka if there is no DSA
header. Of course, the adjustment should be done only if there _is_ a
DSA header.
Modify the comment too so it is clearer.
Fixes: 4e50025129ef ("net: dsa: generalize overhead for taggers that use both headers and trailers")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Whenever query statistics is issued for trap, devlink subsystem
would also fill-in statistics 'dropped' field. This field indicates
the number of packets HW dropped and failed to report to the device driver,
and thus - to the devlink subsystem itself.
In case if device driver didn't register callback for hard drop
statistics querying, 'dropped' field will be omitted and not filled.
Signed-off-by: Oleksandr Mazur <oleksandr.mazur@plvision.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
flags
The current get_phy_flags() is only processed when we connect to a PHY
via a designed phy-handle property via phylink_of_phy_connect(), but if
we fallback on the internal MDIO bus created by a switch and take the
dsa_slave_phy_connect() path then we would not be processing that flag
and using it at PHY connection time.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If link mtu is too big, mld_newpack() allocates high-order page.
But most mld packets don't need high-order page.
So, it might waste unnecessary pages.
To avoid this, it makes mld_newpack() try to allocate order-0 page.
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable err is being initialized with a value that is never read, the
assignment is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support to create (and destroy) interfaces via a new
rtnetlink kind "wwan". The responsible driver has to use
the new wwan_register_ops() to make this possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In some cases, for example in the upcoming WWAN framework changes,
there's no natural "parent netdev", so sometimes dummy netdevs are
created or similar. IFLA_PARENT_DEV_NAME is a new attribute intended to
contain a device (sysfs, struct device) name that can be used instead
when creating a new netdev, if the rtnetlink family implements it.
As suggested by Parav Pandit, we also introduce IFLA_PARENT_DEV_BUS_NAME
attribute in order to uniquely identify a device on the system (with
bus/name pair).
ip-link(8) support for the generic parent device attributes will help
us avoid code duplication, so no other link type will require a custom
code to handle the parent name attribute. E.g. the WWAN interface
creation command will looks like this:
$ ip link add wwan0-1 parent-dev wwan0 type wwan channel-id 1
So, some future subsystem (or driver) FOO will have an interface
creation command that looks like this:
$ ip link add foo1-3 parent-dev foo1 type foo bar-id 3 baz-type Y
Below is an example of dumping link info of a random device with these
new attributes:
$ ip --details link show wlp0s20f3
4: wlp0s20f3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue
state UP mode DORMANT group default qlen 1000
...
parent_bus pci parent_dev 0000:00:14.3
Co-developed-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Co-developed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Suggested-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to make rtnetlink ops that can create different
kinds of devices, like what we want to add to the WWAN
framework, the priv_size and setup parameters aren't quite
sufficient. Make this easier to manage by allowing ops to
allocate their own netdev via an @alloc method that gets
the tb netlink data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The forward declarations for the iucv_handler callbacks are causing
various compile warnings with gcc-11. Reshuffle the code to get rid
of these prototypes.
Reported-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add SEQPACKET ops for loopback transport and 'seqpacket_allow()'
callback.
Signed-off-by: Arseny Krasnov <arseny.krasnov@kaspersky.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|