| Age | Commit message (Collapse) | Author |
|---|
|
Make sure to check ASYNC_INITIALISED before raising DTR when waking up
from blocked open in block_til_ready.
Currently DTR could get raised at hang up as a blocked process would
raise DTR unconditionally before checking for hang up and returning.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to check ASYNC_INITIALISED before raising DTR when waking up
from blocked open in block_til_ready.
Currently DTR could get raised at hang up as a blocked process would
raise DTR unconditionally before checking for hang up and returning.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure to check ASYNC_INITIALISED before raising DTR when waking up
from blocked open in block_til_ready.
Currently DTR could get raised at hang up as a blocked process would
raise DTR unconditionally before checking for hang up and returning.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes the stub for dw8250_probe_acpi() that is used
when compiling without ACPI enabled. The argument type was
wrong.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use resource managed ioremap.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Designware UART has an optional support for 16750
compatible Auto Flow Control. This will enable it based on
the AFCE bit in Component Parameter Register.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The new ACPI DMA helpers in dmaengine API can take care of
extracting all the necessary information regarding DMA. The
driver does not need to do this separately any more.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Lynxpoint LPSS peripheral clocks are now handled in clk
framework so the drivers do not need to take care of them
manually. In dw8250_probe_acpi(), the uartclk is now taken
from the driver_data only if it was not already set.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This allows ACPI to put the device to D3 when it's not used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some slave channel parameters will be always the same. For
example, direction for the Rx channel will always be
DMA_DEV_TO_MEM and DMA_MEM_TO_DEV for Tx channel.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The helper functions in dmaengine API allow the drivers to
request slave channels without the filter parameters. They
will attempt to extract the needed DMA client information
from DT or ACPI, but if such information is not available
the filter parameters can still be used.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Overrun, parity and framing errors should be handled in
8250_core. This also adds check for the dma_status and exits
if the channel is not idle.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Removing one unneeded uart_write_wakeup(). There is no need
to start PIO transfer unless DMA fails, so this also changes
serial8250_tx_dma() to return 0 unless that is the case.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are a few bugs in the samsung serial driver when built as a
loadable module, which makes the console code unavailable, as well as
giving no access to the 'printascii' early debug function. This adds
the appropriate compile time conditionals.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The registers for the Samsung S3C serial port are currently defined in
the platform specific arch/arm/plat-samsung/include/plat/regs-serial.h
file, which is not visible to multiplatform capable drivers.
Unfortunately, it is not possible to move the file into a more local
place as we should normally try to, because the same registers
may be used in one of four places:
* In the driver itself
* In platform-independent ARM code for early debug output
* In platform_data definitions
* In the Samsung platform power management code
I have also found no way to logically split out a platform_data
file, other than possibly move everything into
include/linux/platform_data, which also felt wrong. The only
part of this file that makes sense to keep specific to the s3c24xx
platform are the virtual and physical addresses defined here,
which are needed in no other location.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With the common clock interface, there is no way to provide the
"clock_source" sysfs attribute for the samsung serial ports. Given that
this file was purely informational and had fixed contents, we have reason
to believe that no user space programs were relying on it.
The sysfs file is not documented in the ABI docs.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As Ilya Zykov identified in his patch 'PROBLEM: Race condition in
tty buffer's function flush_to_ldisc()', a race condition exists
which allows a parallel flush_to_ldisc() to flush and free the tty
flip buffers while those buffers are in-use. For example,
CPU 0 | CPU 1 | CPU 2
| flush_to_ldisc() |
| grab spin lock |
tty_buffer_flush() | | flush_to_ldisc()
wait for spin lock | | wait for spin lock
| if (!test_and_set_bit(TTYP_FLUSHING)) |
| while (next flip buffer) |
| ... |
| drop spin lock |
grab spin lock | |
if (test_bit(TTYP_FLUSHING)) | |
set_bit(TTYP_FLUSHPENDING) | receive_buf() |
drop spin lock | |
| | grab spin lock
| | if (!test_and_set_bit(TTYP_FLUSHING))
| | if (test_bit(TTYP_FLUSHPENDING))
| | __tty_buffer_flush()
CPU 2 has just flushed and freed all tty flip buffers while CPU 1 is
transferring data from the head flip buffer.
The original patch was rejected under the assumption that parallel
flush_to_ldisc() was not possible. Because of necessary changes to
the workqueue api, work items can execute in parallel on SMP.
This patch differs slightly from the original patch by testing for
a pending flush _after_ each receive_buf(), since TTYP_FLUSHPENDING
can only be set while the lock is dropped around receive_buf().
Reported-by: Ilya Zykov <linux@izyk.ru>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Ilya Zykov <linux@izyk.ru>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Following patch will fix build error if CONFIG_DMA_ENGINE is unset.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the fixes here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"Two fixes for slave-dmaengine.
The first one is for making slave_id value correct for dw_dmac and
the other one fixes the endieness in DT parsing"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dw_dmac: adjust slave_id accordingly to request line base
dmaengine: dw_dma: fix endianess for DT xlate function
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"For a some fixes for Kernel 3.9:
- subsystem build fix when VIDEO_DEV=y, VIDEO_V4L2=m and I2C=m
- compilation fix for arm multiarch preventing IR_RX51 to be selected
- regression fix at bttv crop logic
- s5p-mfc/m5mols/exynos: a few fixes for cameras on exynos hardware"
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] [REGRESSION] bt8xx: Fix too large height in cropcap
[media] fix compilation with both V4L2 and I2C as 'm'
[media] m5mols: Fix bug in stream on handler
[media] s5p-fimc: Do not attempt to disable not enabled media pipeline
[media] s5p-mfc: Fix encoder control 15 issue
[media] s5p-mfc: Fix frame skip bug
[media] s5p-fimc: send valid m2m ctx to fimc_m2m_job_finish
[media] exynos-gsc: send valid m2m ctx to gsc_m2m_job_finish
[media] fimc-lite: Fix the variable type to avoid possible crash
[media] fimc-lite: Initialize 'step' field in fimc_lite_ctrl structure
[media] ir: IR_RX51 only works on OMAP2
|
|
Pull block fixes from Jens Axboe:
"Alright, this time from 10K up in the air.
Collection of fixes that have been queued up since the merge window
opened, hence postponed until later in the cycle. The pull request
contains:
- A bunch of fixes for the xen blk front/back driver.
- A round of fixes for the new IBM RamSan driver, fixing various
nasty issues.
- Fixes for multiple drives from Wei Yongjun, bad handling of return
values and wrong pointer math.
- A fix for loop properly killing partitions when being detached."
* tag 'for-linus-20130331' of git://git.kernel.dk/linux-block: (25 commits)
mg_disk: fix error return code in mg_probe()
rsxx: remove unused variable
rsxx: enable error return of rsxx_eeh_save_issued_dmas()
block: removes dynamic allocation on stack
Block: blk-flush: Fixed indent code style
cciss: fix invalid use of sizeof in cciss_find_cfgtables()
loop: cleanup partitions when detaching loop device
loop: fix error return code in loop_add()
mtip32xx: fix error return code in mtip_pci_probe()
xen-blkfront: remove frame list from blk_shadow
xen-blkfront: pre-allocate pages for requests
xen-blkback: don't store dev_bus_addr
xen-blkfront: switch from llist to list
xen-blkback: fix foreach_grant_safe to handle empty lists
xen-blkfront: replace kmalloc and then memcpy with kmemdup
xen-blkback: fix dispatch_rw_block_io() error path
rsxx: fix missing unlock on error return in rsxx_eeh_remap_dmas()
Adding in EEH support to the IBM FlashSystem 70/80 device driver
block: IBM RamSan 70/80 error message bug fix.
block: IBM RamSan 70/80 branding changes.
...
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"This includes the bug-fix for a >= v3.8-rc1 regression specific to
iscsi-target persistent reservation conflict handling (CC'ed to
stable), and a tcm_vhost patch to drop VIRTIO_RING_F_EVENT_IDX usage
so that in-flight qemu vhost-scsi-pci device code can detect the
proper vhost feature bits.
Also, there are two more tcm_vhost patches still being discussed by
MST and Asias for v3.9 that will be required for the in-flight qemu
vhost-scsi-pci device patch to function properly, and that should
(hopefully) be the last target fixes for this round."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit
|
|
On some hardware configurations we have got the request line with the offset.
The patch introduces convert_slave_id() helper for that cases. The request line
base is came from the driver data provided by the platform_device_id table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
As reported by Wu Fengguang's build robot tracking sparse warnings, the
dma_spec arguments in the dw_dma_xlate are already byte swapped on
little-endian platforms and must not get swapped again. This code is
currently not used anywhere, but will be used in Linux 3.10 when the
ARM SPEAr platform starts using the generic DMA DT binding.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull ceph fix from Sage Weil:
"This fixes a regression introduced during the last merge window when
mapping non-existent images."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
rbd: don't zero-fill non-image object requests
|
|
A result of ENOENT from a read request for an object that's part of
an rbd image indicates that there is a hole in that portion of the
image. Similarly, a short read for such an object indicates that
the remainder of the read should be interpreted a full read with
zeros filling out the end of the request.
This behavior is not correct for objects that are not backing rbd
image data. Currently rbd_img_obj_request_callback() assumes it
should be done for all objects.
Change rbd_img_obj_request_callback() so it only does this zeroing
for image objects. Encapsulate that special handling in its own
function. Add an assertion that the image object request is a bio
request, since we assume that (and we currently don't support any
other types).
This resolves a problem identified here:
http://tracker.ceph.com/issues/4559
The regression was introduced by bf0d5f503dc11d6314c0503591d258d60ee9c944.
Reported-by: Dan van der Ster <dan@vanderster.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-off-by: Sage Weil <sage@inktank.com>
|
|
In DMA support, The received data is not pushed to tty until the DMA buffer
is filled. But some megabyte rate chips such as BT expect fast response and
data should be pushed immediately. In order to fix this issue, We suggest
the use of the timer for polling DMA buffer.
In our test, no data loss occurred at high-baudrate as compared with interrupt-
driven (We tested with 3Mbps).
We changes:
- We add timer for polling. If we set poll_timer to 10, every 10ms,
timer handler checks the residue in the dma buffer and transfer data
to the tty. Also, last_residue is updated for the next polling.
- poll_timeout is used to prevent the timer's system cost.
If poll_timeout is set to 3000 and no data is received in 3 seconds,
we inactivate poll timer and driver falls back to interrupt-driven.
When data is received again in FIFO and UART irq is occurred, we switch
back to DMA mode and start polling.
- We use consistent DMA mappings to avoid from the frequent cache operation
of the timer function for default.
- pl011_dma_rx_chars is modified. the pending size is recalculated because
data can be taken by polling.
- the polling time is adjusted if dma rx poll is enabled but no rate is
specified. Ideal polling interval to push 1 character at every interval
is the reciprocal of 'baud rate / 10 line bits per character / 1000 ms
per sec'. But It is very aggressive to system. Experimentally,
'10000000 / baud' is suitable to receive dozens of characters. the poll rate
can be specified statically by dma_rx_poll_rate of the platform data as well.
Changes compared to v1:
- Use of consistent DMA mappings.
- Added dma_rx_poll_rate in platform data to specify the polling interval.
- Added dma_rx_poll_timeout in platform data to specify the polling timeout.
Changes compared to v2:
- Use of consistent DMA mappings for default.
- Added dma_rx_poll_enable in platform data to adjust the polling time
according to the baud rate.
- remove unnecessary lock from the polling function.
Signed-off-by: Chanho Min <chanho.min@lge.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes a regression introduced in v3.8-rc1 code where a failed
target_check_reservation() check in target_setup_cmd_from_cdb() was causing
an incorrect SAM_STAT_GOOD status to be returned during a WRITE operation
performed by an unregistered / unreserved iscsi initiator port.
This regression is only effecting iscsi-target due to a special case check
for TCM_RESERVATION_CONFLICT within iscsi_target_erl1.c:iscsit_execute_cmd(),
and was still correctly disallowing WRITE commands from backend submission
for unregistered / unreserved initiator ports, while returning the incorrect
SAM_STAT_GOOD status due to the missing SAM_STAT_RESERVATION_CONFLICT
assignment.
This regression was first introduced with:
commit de103c93aff0bed0ae984274e5dc8b95899badab
Author: Christoph Hellwig <hch@lst.de>
Date: Tue Nov 6 12:24:09 2012 -0800
target: pass sense_reason as a return value
Go ahead and re-add the missing SAM_STAT_RESERVATION_CONFLICT assignment
during a target_check_reservation() failure, so that iscsi-target code
sends the correct SCSI status.
All other fabrics using target_submit_cmd_*() with a RESERVATION_CONFLICT
call to transport_generic_request_failure() are not effected by this bug.
Reported-by: Jeff Leung <jleung@curriegrad2004.ca>
Cc: Christoph Hellwig <hch@lst.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This patch adds a VHOST_SCSI_FEATURES mask minus VIRTIO_RING_F_EVENT_IDX
so that vhost-scsi-pci userspace will strip this feature bit once
GET_FEATURES reports it as being unsupported on the host.
This is to avoid a bug where ->handle_kicks() are missed when EVENT_IDX
is enabled by default in userspace code.
(mst: Rename to VHOST_SCSI_FEATURES + add comment)
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Asias He <asias@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This commit implements support for using the clk api; this lets us use
the "clocks" property with device tree, instead of having to use
clock-frequency.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The no_console_suspend option allows the console to write to the UART
during early resume, before the serial port itself is resumed. Such
writes hang indefinitely waiting for TX ready.
This adds a check to the console putchar function to drop characters
instead of hanging if the port hasn't been initialized. That way, we
can use no_console_suspend without risk of hanging.
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This closes a window where the system may hang in resume as soon as the
UART interrupt is enabled and before the mask is restored. The hang occurs
because the driver can't handle IRQs it thinks are masked.
Signed-off-by: Michael Spang <spang@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since the interrupt mask register is not preserved across system suspend
and it defaults to all interrupts enabled, it is not enough to disable
UART interrupt.
This patch adds free_irq to port shutdown and mask setting to port
startup to handle IRQ disabling in a suspend-friendly way. In addition,
a bug caused by multiple request_irq calls in port startup callback is
fixed.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are some USB fixes to resolve issues reported recently, as well
as a new device id for the ftdi_sio driver."
* tag 'usb-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD
usb: Fix compile error by selecting USB_OTG_UTILS
USB: serial: fix hang when opening port
USB: EHCI: fix bug in iTD/siTD DMA pool allocation
xhci: Don't warn on empty ring for suspended devices.
usb: xhci: Fix TRB transfer length macro used for Event TRB.
usb/acpi: binding xhci root hub usb port with ACPI
usb: add find_raw_port_number callback to struct hc_driver()
usb: xhci: fix build warning
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/serial fixes from Greg Kroah-Hartman:
"Here are some tty/serial driver fixes for 3.9.
The big thing here is the fix for the huge mess we caused renaming the
8250 driver accidentally in the 3.7 kernel release, without realizing
that there were users of the module options that suddenly broke. This
is now resolved, and, to top the injury off, we have a backwards-
compatible option for those users who got used to the new name since
3.7. Ugh, sorry about that.
Other than that, some other minor fixes for issues that have been
reported by users."
* tag 'tty-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Xilinx: ARM: UART: clear pending irqs before enabling irqs
TTY: 8250, deprecated 8250_core.* options
TTY: 8250, revert module name change
serial: 8250_pci: Add WCH CH352 quirk to avoid Xscale detection
tty: atmel_serial_probe(): index of atmel_ports[] fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver fixes from Greg Kroah-Hartman:
"Here are two tiny staging driver fixes to resolve issues that have
been reported."
* tag 'staging-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: comedi: s626: fix continuous acquisition
staging: zcache: fix typo "64_BIT"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg Kroah-Hartman:
"Here are some small char/misc driver fixes that resolve issues
recently reported against the 3.9-rc kernels. All have been in
linux-next for a while."
* tag 'char-misc-3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
VMCI: Fix process-to-process DRGAMs.
mei: ME hardware reset needs to be synchronized
mei: add mei_stop function to stop mei device
extcon: max77693: Initialize register of MUIC device to bring up it without platform data
extcon: max77693: Fix bug of wrong pointer when platform data is not used
extcon: max8997: Check the pointer of platform data to protect null pointer error
|
|
Consider a situation where I have an ARM based system
and therefore no legacy ports. Say, I have two
memory-mapped ports. I use device tree to describe the
ports. What would be the config options I set so that
I get only the two ports in my system? I do not want
legacy ports being created automatically and I want
it to be flexible enough that it creates the devices
based only on the device tree. I expected setting
SERIAL_8250_RUNTIME_UARTS = 0 to work because the
description said, "Set this to the maximum number of
serial ports you want the kernel to register at boot
time." Unfortunately, even though SERIAL_8250_NR_UARTS
was set to the default value of 4, I did not get any device
nodes (because SERIAL_8250_RUNTIME_UARTS was 0). This
is what this change is addressing.
SERIAL_8250_NR_UARTS controls the maximum number of ports
you can support. SERIAL_8250_RUNTIME_UARTS specifies the
number of ports you want to create automatically for legacy
ports at boot time. All other ports will be created
when serial8250_register_port is called (and if does not exceed
the total number of supported ports as specified by
SERIAL_8250_NR_UARTS).
Signed-off-by: Karthik Manamcheri <karthik.manamcheri@ni.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael J Wysocki:
- Fix for a recent cpufreq regression related to acpi-cpufreq and
suspend/resume from Viresh Kumar.
- cpufreq stats reference counting fix from Viresh Kumar.
- intel_pstate driver fixes from Dirk Brandewie and Konrad Rzeszutek
Wilk.
- New ACPI suspend blacklist entry for Sony Vaio VGN-FW21M from Fabio
Valentini.
- ACPI Platform Error Interface (APEI) fix from Chen Gong.
- PCI root bridge hotplug locking fix from Yinghai Lu.
* tag 'pm+acpi-3.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PCI / ACPI: hold acpi_scan_lock during root bus hotplug
ACPI / APEI: fix error status check condition for CPER
ACPI / PM: fix suspend and resume on Sony Vaio VGN-FW21M
cpufreq: acpi-cpufreq: Don't set policy->related_cpus from .init()
cpufreq: stats: do cpufreq_cpu_put() corresponding to cpufreq_cpu_get()
intel-pstate: Use #defines instead of hard-coded values.
cpufreq / intel_pstate: Fix calculation of current frequency
cpufreq / intel_pstate: Add function to check that all MSRs are valid
|
|
Pull crypto fixes from Herbert Xu:
"This removes IPsec ESN support from the talitos/caam drivers since
they were implemented incorrectly, causing interoperability problems
if ESN is used with them."
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
Revert "crypto: caam - add IPsec ESN support"
Revert "crypto: talitos - add IPsec ESN support"
|
|
Pull fbdev fixes from Tomi Valkeinen:
"Since Florian is still away/inactive, I volunteered to collect fbdev
fixes for 3.9 and changes for 3.10. I didn't receive any other fbdev
fixes than OMAP yet, but I didn't want to delay this further as
there's a compilation fix for OMAP1. So there could be still some
fbdev fixes on the way a bit later.
This contains:
- Fix OMAP1 compilation
- OMAP display fixes"
* tag 'fbdev-fixes-3.9-rc4' of git://gitorious.org/linux-omap-dss2/linux:
omapdss: features: fix supported outputs for OMAP4
OMAPDSS: tpo-td043 panel: fix data passing between SPI/DSS parts
omapfb: fix broken build on OMAP1
|
|
It enhances the driver for FTDI-based USB serial adapters
to recognize Mitsubishi Electric Corp. USB/RS422 Converters
as FT232BM chips and support them.
https://search.meau.com/?q=FX-USB-AW
Signed-off-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Tested-by: Konstantin Holoborodko <klh.kernel@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
* acpi-fixes:
PCI / ACPI: hold acpi_scan_lock during root bus hotplug
ACPI / APEI: fix error status check condition for CPER
ACPI / PM: fix suspend and resume on Sony Vaio VGN-FW21M
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
"This is mostly just the last stragglers of the regression bugs that
this merge window had. There are also two bug-fixes: one that adds an
extra layer of security, and a regression fix for a change that was
added in v3.7 (the v1 was faulty, the v2 works).
- Regression fixes for C-and-P states not being parsed properly.
- Fix possible security issue with guests triggering DoS via
non-assigned MSI-Xs.
- Fix regression (introduced in v3.7) with raising an event (v2).
- Fix hastily introduced band-aid during c0 for the CR3 blowup."
* tag 'stable/for-linus-3.9-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/events: avoid race with raising an event in unmask_evtchn()
xen/mmu: Move the setting of pvops.write_cr3 to later phase in bootup.
xen/acpi-stub: Disable it b/c the acpi_processor_add is no longer called.
xen-pciback: notify hypervisor about devices intended to be assigned to guests
xen/acpi-processor: Don't dereference struct acpi_processor on all CPUs.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid
Pull HID fixes from Jiri Kosina:
- fix for potential 3.9 regression in handling of buttons for touchpads
following HID mt specification; potential because reportedly there is
no retail product on the market that would be using this feature, but
nevertheless we'd better follow the spec. Fix by Benjamin Tissoires.
- support for two quirky devices added by Josh Boyer.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: multitouch: fix touchpad buttons
HID: usbhid: fix build problem
HID: usbhid: quirk for MSI GX680R led panel
HID: usbhid: quirk for Realtek Multi-card reader
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"Here are some fixes which have collected since Linux v3.9-rc1.
The most important one fixes a long-standing regressen which make
re-hotplugged devices unusable when AMD IOMMU is used.
The other patches fix build issues (build regression on OMAP and a
section mismatch). One patch just removes a duplicate header include."
* tag 'iommu-fixes-v3.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Make sure dma_ops are set for hotplug devices
x86, io_apic: remove duplicated include from irq_remapping.c
iommu: OMAP: build only on OMAP2+
amd_iommu_init: remove __init from amd_iommu_erratum_746_workaround
|
|
In unmask_evtchn(), when the mask bit is cleared after testing for
pending and the event becomes pending between the test and clear, then
the upcall will not become pending and the event may be lost or
delayed.
Avoid this by always clearing the mask bit before checking for
pending. If a hypercall is needed, remask the event as
EVTCHNOP_unmask will only retrigger pending events if they were
masked.
This fixes a regression introduced in 3.7 by
b5e579232d635b79a3da052964cb357ccda8d9ea (xen/events: fix
unmask_evtchn for PV on HVM guests) which reordered the clear mask and
check pending operations.
Changes in v2:
- set mask before hypercall.
Cc: stable@vger.kernel.org
Acked-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: David Vrabel <david.vrabel@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
|