| Age | Commit message (Collapse) | Author |
|---|
|
This simplifies the error paths and device unbinding.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This function is new in v4.2-rc1 and makes a forward declaration of the
match table superfluous which can so be removed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Since commit ef90174f8210 ("watchdog: watchdog_core: Add watchdog
registration deferral mechanism") there is no need to delay the call to
watchdog_register_device any more. So simplify the registration code
accordingly.
Resetting wd_base to NULL can the also be dropped because nothing
depends on it being NULL to signal probe failure any more. (The matching
wd_base = NULL in .remove was missing, too.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
This commit adds support for the watchdog timer found in NXP LPC SoCs
family, which includes LPC18xx/LPC43xx. Other SoCs in that family may
share the same watchdog hardware.
Watchdog driver registers a restart handler that will restart the system
by performing an incorrect feed after ensuring the watchdog is enabled in
reset mode.
As watchdog cannot be disabled in hardware, driver's stop routine will
regularly send a keepalive ping using a timer.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
During probe for an always-running watchdog a timer is setup to
constantly ping the watchdog while the device is not open. The gpio to
ping the watchdog is setup to inactive.
For a watchdog with hw_algo = "toggle" this results in a ping depending
on the initial state of the gpio, for hw_algo = "level" no ping is
generated.
Make sure that the first automatic ping is sent immediately and not only
when the timer expires the first time. This makes the machine survive in
case more than half of the watchdog timeout is already elapsed. (Which
is very probable for the chip I'm faced with that has a timeout of one
second.)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
strncmp(algo, "toggle", 6) doesn't compare the trailing '\0' byte, so
using
hw_algo = "toggleboggle"
is recognized the same way as
hw_algo = "toggle"
. While this doesn't introduce any problems for a device tree that
sticks to the documented settings it's still ugly.
Fix this by using strcmp to only match on "toggle" and "level".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The watchdog infrastructure checks the maximum timeout for us.
Use it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Tested on the Nvidia chipset with an SMBus controller PCI ID 0x0AA2
(as shown in the PCI listing during the boot sequence).
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Commit f2147de33470 ("watchdog: sunxi: support parameterized compatible
strings") introduced a regression in sunxi_wdt_start(), by which
the system reset function of the watchdog is not enabled upon
starting the watchdog. As a result, the system is not reset when the
watchdog expires. Fix it.
Fixes: f2147de33470 ("watchdog: sunxi: support parameterized compatible strings")
Signed-off-by: Francesco Lavra <francescolavra.fl@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: stable@vger.kernel.org
|
|
Without .shutdown(), watchdog might reset the system during power off.
For example, if watchdog's timeout is set to 30s, then it is reset to
zero by mtk_wdt_ping(). During power off, no app will ping watchdog,
but watchdog is still running and may trigger reset.
Signed-off-by: Greta Zhang <greta.zhang@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
add mediatek watchdog driver suspend/resume support
Signed-off-by: Greta Zhang <greta.zhang@mediatek.com>
Signed-off-by: Roger Lu <roger.lu@mediatek.com>
Signed-off-by: Eddie Huang <eddie.huang@mediatek.com>
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Commit c631f20068 ("watchdog: imgpdc: Add reboot support") introduced
a restart handler but forgot to unregister it on driver removal. Fix it.
Fixes: c631f20068 ("watchdog: imgpdc: Add reboot support")
Reported-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A couple of major (hang and deadlock) fixes with fortunately fairly
rare triggering conditions. The PM oops is only really triggered by
people using enclosure services (rare) and the fnic driver is mostly
used in enterprise environments"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
SCSI: Fix NULL pointer dereference in runtime PM
fnic: Use the local variable instead of I/O flag to acquire io_req_lock in fnic_queuecommand() to avoid deadloack
|
|
Pull MIPS bug fixes from Ralf Baechle:
"Two more fixes for 4.2.
One fixes a build issue with the LLVM assembler - LLVM assembler macro
names are case sensitive, GNU as macro names are insensitive; the
other corrects a license string (GPL v2, not GPLv2) such that the
module loader will recognice the license correctly"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
FIRMWARE: bcm47xx_nvram: Fix module license.
MIPS: Fix LLVM build issue.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A series of small fixlets for a regression visible on OMAP devices
caused by the conversion of the OMAP interrupt chips to hierarchical
interrupt domains. Mostly one liners on the driver side plus a small
helper function in the core to avoid open coded mess in the drivers"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/crossbar: Restore set_wake functionality
irqchip/crossbar: Restore the mask on suspend behaviour
ARM: OMAP: wakeupgen: Restore the irq_set_type() mechanism
irqchip/crossbar: Restore the irq_set_type() mechanism
genirq: Introduce irq_chip_set_type_parent() helper
genirq: Don't return ENOSYS in irq_chip_retrigger_hierarchy
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"Two minimalistic fixes for 4.2 regressions:
- Eric fixed a thinko in the timer_list base switching code caused by
the overhaul of the timer wheel. It can cause a cpu to see the
wrong base for a timer while we move the timer around.
- Guenter fixed a regression for IMX if booted w/o device tree, where
the timer interrupt is not initialized and therefor the machine
fails to boot"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/imx: Fix boot with non-DT systems
timer: Write timer->flags atomically
|
|
Commit c48a11c7ad26 ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():
if (page->pfmemalloc && !page->mapping)
skb->pfmemalloc = true;
It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted. However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone. Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.
So the assumption is invalid if the networking code can see such a page.
And it seems it can. We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf. There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.
The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead. We can reuse the index
again but define it to an impossible value (-1UL). This is the page
index so it should never see the value that large. Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.
The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g. what SLAB and SLUB do).
[akpm@linux-foundation.org: fix blooper in slub]
Fixes: c48a11c7ad26 ("netvm: propagate page->pfmemalloc to skb")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Debugged-by: Vlastimil Babka <vbabka@suse.com>
Debugged-by: Jiri Bohac <jbohac@suse.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org> [3.6+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
"These are fixes for ASPM-related NULL pointer dereference crashes on
Sparc and PowerPC and 64-bit PCI address-related HPMC crashes on
PA-RISC. These are both caused by things we merged in the v4.2 merge
window. Details:
Resource management
- Don't use 64-bit bus addresses on PA-RISC
Miscellaneous
- Tolerate hierarchies with no Root Port"
* tag 'pci-v4.2-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Don't use 64-bit bus addresses on PA-RISC
PCI: Tolerate hierarchies with no Root Port
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a regression fix at the videobuf2 core driver
- fix error handling at mantis probing code
- revert the IR encode patches, as the API is not mature enough.
So, better to postpone the changes to a latter Kernel
- fix Kconfig breakages on some randconfig scenarios.
* tag 'media/v4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] mantis: Fix error handling in mantis_dma_init()
Revert "[media] rc: rc-ir-raw: Add scancode encoder callback"
Revert "[media] rc: rc-ir-raw: Add Manchester encoder (phase encoder) helper"
Revert "[media] rc: ir-rc5-decoder: Add encode capability"
Revert "[media] rc: ir-rc6-decoder: Add encode capability"
Revert "[media] rc: rc-core: Add support for encode_wakeup drivers"
Revert "[media] rc: rc-loopback: Add loopback of filter scancodes"
Revert "[media] rc: nuvoton-cir: Add support for writing wakeup samples via sysfs filter callback"
[media] vb2: Fix compilation breakage when !CONFIG_BUG
[media] vb2: Only requeue buffers immediately once streaming is started
[media] media/pci/cobalt: fix Kconfig and build when SND is not enabled
[media] media/dvb: fix ts2020.c Kconfig and build
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input layer fix from Dmitry Torokhov:
"A small fixup to gpio_keys_polled driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gpio_keys_polled - request GPIO pin as input.
|
|
Pull drm fixes from Dave Airlie:
"A bunch of i915 fixes, one revert a VBT fix that was a bit premature,
and some braswell feature removal that the hw actually didn't support.
One radeon race fix at boot, and one hlcdc build fix, one fix from
Russell that fixes build as well with new audio features.
This is hopefully all I have until -next"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon: fix hotplug race at startup
drm/edid: add function to help find SADs
drm/i915: Avoid TP3 on CHV
drm/i915: remove HBR2 from chv supported list
Revert "drm/i915: Add eDP intermediate frequencies for CHV"
Revert "drm/i915: Allow parsing of variable size child device entries from VBT"
drm/atmel-hlcdc: Compile suspend/resume for PM_SLEEP only
drm/i915: Flag the execlists context object as dirty after every use
|
|
We apparantly get a hotplug irq before we've initialised
modesetting,
[drm] Loading R100 Microcode
BUG: unable to handle kernel NULL pointer dereference at (null)
IP: [<c125f56f>] __mutex_lock_slowpath+0x23/0x91
*pde = 00000000
Oops: 0002 [#1]
Modules linked in: radeon(+) drm_kms_helper ttm drm i2c_algo_bit backlight pcspkr psmouse evdev sr_mod input_leds led_class cdrom sg parport_pc parport floppy intel_agp intel_gtt lpc_ich acpi_cpufreq processor button mfd_core agpgart uhci_hcd ehci_hcd rng_core snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm usbcore usb_common i2c_i801 i2c_core snd_timer snd soundcore thermal_sys
CPU: 0 PID: 15 Comm: kworker/0:1 Not tainted 4.2.0-rc7-00015-gbf67402 #111
Hardware name: MicroLink /D850MV , BIOS MV85010A.86A.0067.P24.0304081124 04/08/2003
Workqueue: events radeon_hotplug_work_func [radeon]
task: f6ca5900 ti: f6d3e000 task.ti: f6d3e000
EIP: 0060:[<c125f56f>] EFLAGS: 00010282 CPU: 0
EIP is at __mutex_lock_slowpath+0x23/0x91
EAX: 00000000 EBX: f5e900fc ECX: 00000000 EDX: fffffffe
ESI: f6ca5900 EDI: f5e90100 EBP: f5e90000 ESP: f6d3ff0c
DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
CR0: 8005003b CR2: 00000000 CR3: 36f61000 CR4: 000006d0
Stack:
f5e90100 00000000 c103c4c1 f6d2a5a0 f5e900fc f6df394c c125f162 f8b0faca
f6d2a5a0 c138ca00 f6df394c f7395600 c1034741 00d40000 00000000 f6d2a5a0
c138ca00 f6d2a5b8 c138ca10 c1034b58 00000001 f6d40000 f6ca5900 f6d0c940
Call Trace:
[<c103c4c1>] ? dequeue_task_fair+0xa4/0xb7
[<c125f162>] ? mutex_lock+0x9/0xa
[<f8b0faca>] ? radeon_hotplug_work_func+0x17/0x57 [radeon]
[<c1034741>] ? process_one_work+0xfc/0x194
[<c1034b58>] ? worker_thread+0x18d/0x218
[<c10349cb>] ? rescuer_thread+0x1d5/0x1d5
[<c103742a>] ? kthread+0x7b/0x80
[<c12601c0>] ? ret_from_kernel_thread+0x20/0x30
[<c10373af>] ? init_completion+0x18/0x18
Code: 42 08 e8 8e a6 dd ff c3 57 56 53 83 ec 0c 8b 35 48 f7 37 c1 8b 10 4a 74 1a 89 c3 8d 78 04 8b 40 08 89 63
Reported-and-Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
Revert of a VBT parsing commit that should've been queued for drm-next,
not v4.2. The revert unbreaks Braswell among other things.
Also on Braswell removal of DP HBR2/TP3 and intermediate eDP frequency
support. The code was optimistically added based on incorrect
documentation; the platform does not support them. These are cc: stable.
Finally a gpu state fix from Chris, also cc: stable.
* tag 'drm-intel-fixes-2015-08-20' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Avoid TP3 on CHV
drm/i915: remove HBR2 from chv supported list
Revert "drm/i915: Add eDP intermediate frequencies for CHV"
Revert "drm/i915: Allow parsing of variable size child device entries from VBT"
drm/i915: Flag the execlists context object as dirty after every use
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix a recent regression in the ACPI backlight code and a memory
leak in the Exynos cpufreq driver.
Specifics:
- Fix a recently introduced issue in the ACPI backlight code which
causes lockdep to complain about a circular lock dependency during
initialization (Hans de Goede).
- Fix a possible memory during initialization in the Exynos cpufreq
driver (Shailendra Verma)"
* tag 'pm+acpi-4.2-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: exynos: Fix for memory leak in case SoC name does not match
ACPI / video: Fix circular lock dependency issue in the video-detect code
|
|
* acpi-video:
ACPI / video: Fix circular lock dependency issue in the video-detect code
* cpufreq-fixes:
cpufreq: exynos: Fix for memory leak in case SoC name does not match
|
|
Meelis and Helge reported that 3a9ad0b4fdcd ("PCI: Add pci_bus_addr_t")
caused HPMCs on A500 and hangs on rp5470.
PA-RISC does not set ARCH_DMA_ADDR_T_64BIT, even for 64-bit kernels, so
prior to 3a9ad0b4fdcd, we always used 32-bit PCI addresses. After
3a9ad0b4fdcd, we do use 64-bit PCI addresses in 64-bit kernels, and
apparently there's some PA-RISC problem related to them.
Fixes: 3a9ad0b4fdcd ("PCI: Add pci_bus_addr_t")
Link: http://lkml.kernel.org/r/alpine.LRH.2.11.1507260929000.30065@math.ut.ee
Reported-by: Meelis Roos <mroos@linux.ee>
Reported-by: Helge Deller <deller@gmx.de>
Tested-by: Helge Deller <deller@gmx.de>
Based-on-idea-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Yinghai Lu <yinghai@kernel.org>
CC: stable@vger.kernel.org # v3.19+
|
|
Pull networking fixes from David Miller:
1) Out of bounds array access in 802.11 minstrel code, from Adrien
Schildknecht.
2) Don't use skb_get() in IGMP/MLD code paths, as this makes
pskb_may_pull() BUG. From Linus Luessing.
3) Fix off by one in ipv4 route dumping code, from Andy Whitcroft.
4) Fix deadlock in reqsk_queue_unlink(), from Eric Dumazet.
5) Fix ppp device deregistration wrt. netns deletion, from Guillaume
Nault.
6) Fix deadlock when creating per-cpu ipv6 routes, from Martin KaFai
Lau.
7) Fix memory leak in batman-adv code, from Sven Eckelmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
batman-adv: Fix memory leak on tt add with invalid vlan
net: phy: fix semicolon.cocci warnings
net: qmi_wwan: add HP lt4111 LTE/EV-DO/HSPA+ Gobi 4G Module
be2net: avoid vxlan offloading on multichannel configs
ipv6: Fix a potential deadlock when creating pcpu rt
ipv6: Add rt6_make_pcpu_route()
ipv6: Remove un-used argument from ip6_dst_alloc()
net: phy: workaround for buggy cable detection by LAN8700 after cable plugging
net: ethernet: micrel: fix an error code
ppp: fix device unregistration upon netns deletion
net: phy: fix PHY_RUNNING in phy_state_machine
Revert "net: limit tcp/udp rmem/wmem to SOCK_{RCV,SND}BUF_MIN"
inet: fix potential deadlock in reqsk_queue_unlink()
gianfar: Restore link state settings after MAC reset
ipv4: off-by-one in continuation handling in /proc/net/route
net: fix wrong skb_get() usage / crash in IGMP/MLD parsing code
mac80211: fix invalid read in minstrel_sort_best_tp_rates()
|
|
GPIOF_IN flag was lost in:
Commit 633a21d80b4a("input: gpio_keys_polled: Add support for GPIO
descriptors").
Without this flag, legacy code path (for non-descriptor GPIO declarations)
would configure GPIO as output (0 meaning GPIOF_DIR_OUT | GPIOF_INIT_LOW).
Cc: stable@vger.kernel.org
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"This contains a v4.2-rc specific RCU module unload regression bug-fix,
a long-standing iscsi-target bug-fix for duplicate target_xfer_tags
during NOP processing from Alexei, and two more small REPORT_LUNs
emulation related patches to make Solaris FC host LUN scanning happy
from Roland.
There is also one patch not included that allows target-core to limit
the number of fabric driver SGLs per I/O request using residuals, that
is currently required as a work-around for FC hosts which don't honor
EVPD block-limits settings. At this point, it will most likely become
for-next material"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix handling of small allocation lengths in REPORT LUNS
target: REPORT LUNS should return LUN 0 even for dynamic ACLs
target/iscsi: Fix double free of a TUR followed by a solicited NOPOUT
target: Perform RCU callback barrier before backend/fabric unload
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal fixes from Eduardo Valentin:
"Last minute fixes on the thermal-soc tree. There is a fix of a long
lasting bug in cpu cooling device, thanks for RMK for being pushing
this"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal/cpu_cooling: update policy limits if clipped_freq < policy->max
thermal/cpu_cooling: rename max_freq as clipped_freq in notifier
thermal/cpu_cooling: rename cpufreq_val as clipped_freq
thermal/cpu_cooling: convert 'switch' block to 'if' block in notifier
thermal/cpu_cooling: quit early after updating policy
thermal/cpu_cooling: No need to initialize max_freq to 0
thermal: cpu_cooling: fix lockdep problems in cpu_cooling
thermal: power_allocator: do not use devm* interfaces
|
|
Commit 6dd747825b20 ("ARM: imx: move timer resources into a structure")
moved initialization parameters into a data structure, but neglected to set
the irq field in that data structure for non-DT boots. This causes the system
to hang if a non-DT boot is attempted.
Fixes: 6dd747825b20 ("ARM: imx: move timer resources into a structure")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/1440066441-13930-1-git-send-email-linux@roeck-us.net
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
https://github.com/bbrezillon/linux-at91 into drm-fixes
single atmel hlcdc fix.
* 'drm-atmel-hlcdc-fixes' of https://github.com/bbrezillon/linux-at91:
drm/atmel-hlcdc: Compile suspend/resume for PM_SLEEP only
|
|
The TI crossbar irqchip doesn't provides any facility to configure the
wakeup sources, but the conversion to hierarchical irqdomains set the
irq_set_wake callback to irq_chip_set_wake_parent. The parent chip
(OMAP wakeupgen) has no irq_set_wake function either so the call will
fail with -ENOSYS. As a result the irq_set_wake() call in the resume
path will trigger an 'Unbalanced wake disable' warning.
Before the conversion the GIC irqchip was the top level irqchip and
correctly flagged with IRQCHIP_SKIP_SET_WAKE.
Restore the correct behaviour by removing the irq_set_type callback
from the crossbar irqchip and set the IRQCHIP_SKIP_SET_WAKE flag which
lets the irq_set_irq_wake() call from the driver succeed.
[ tglx: Massaged changelog ]
Fixes: 783d31863fb8 ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-7-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The ARM GIC requires that all interrupts which are not used as a
wakeup source have to be masked during suspend.
The conversion of the crossbar irqchip to hierarchical irq domains
failed to mark the crossbar irqchip with the IRQCHIP_MASK_ON_SUSPEND
flag and therefor broke the suspend requirement of the GIC.
Before the conversion the flags were visible because the GIC was the
top level irqchip. After the conversion the crossbar irqchip is the
top level irq chip whose flags are evaluated in suspend_device_irq().
As the flag is not set the masking of the non-wakeup irqs is not
invoked which breaks suspend.
Add the IRQCHIP_MASK_ON_SUSPEND flag to the crossbar irqchip, so the
GIC interrupts get masked properly.
[ tglx: Massaged changelog ]
Fixes: 783d31863fb8 ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-6-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The conversion of the crossbar irqchip to hierarchical irq domains
failed to provide a mechanism to properly set the trigger type of an
interrupt.
The crossbar irq chip itself has no mechanism and therefor no
irq_set_type() callback. The code before the conversion relayed the
trigger configuration directly to the underlying GIC.
Restore the correct behaviour by setting the crossbar irq_set_type
callback to irq_chip_set_type_parent(). This propagates the
set_trigger() call to the underlying GIC irqchip.
[ tglx: Massaged changelog ]
Fixes: 783d31863fb8 ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-4-git-send-email-grygorii.strashko@ti.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
We should not assume any particular hardware topology. Commit d0751b98dfa3
("PCI: Add dev->has_secondary_link to track downstream PCIe links") relied
on the assumption that every PCIe hierarchy is rooted at a Root Port. But
we can't rely on any assumption about what hardware we will find; we just
have to deal with the world as it is.
On some platforms, PCIe devices (endpoints, switch upstream ports, etc.)
appear directly on the root bus, and there is no Root Port in the PCI bus
hierarchy. For example, Meelis observed these top-level devices on a
Sparc V245:
0000:02:00.0 PCI bridge to [bus 03-0d] Switch Upstream Port
0001:02:00.0 PCI bridge to [bus 03] PCIe to PCI/PCI-X Bridge
These devices *look* like they have links going upstream, but there really
are no upstream devices.
In set_pcie_port_type(), we used the parent device to figure out which side
of a switch port has a link, so if the parent device did not exist, we
dereferenced a NULL parent pointer.
Check whether the parent device exists before dereferencing it.
Meelis observed this oops on Sparc V245 and T2000. Ben Herrenschmidt says
this is also possible on IBM PowerVM guests on PowerPC.
[bhelgaas: changelog, comment]
Link: http://lkml.kernel.org/r/alpine.LRH.2.20.1508122118210.18637@math.ut.ee
Reported-by: Meelis Roos <mroos@linux.ee>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/11020/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Current code assigns 0 to variable 'err', which makes mantis_dma_init()
to return success even if mantis_alloc_buffers() fails.
Fix it by checking the return value from mantis_alloc_buffers() and
propagating it in the case of error.
Reported-by: RUC_Soft_Sec <zy900702@163.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This reverts commit 9869da5bacc5c9b865a183bd36c04be76cdd325d.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This reverts commit 1d971d927efa2e10194c96ed0475b6d6054342d8.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This reverts commit a0466f15b4654cf1ac9e387d7c1a401eff494b4f.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This reverts commit cf257e288ad3a134d4bb809c542a3ae6c87ddfa3.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This reverts commit 0d830b2d1295fee82546d57185da5a6604f11ae2.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This reverts commit 2e4ebde269236da2a41183522127715b6d9d80ce.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
sysfs filter callback"
This reverts commit da7ee60b03bd66bb10974d7444aa444de6391312.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch removes TP3 support on CHV since there is no support
for HBR2 on this platform.
v2: rename the function to indicate it checks source rates (Jani)
v3: update comment to indicate TP3 dependency on HBR2 supported
hardware (Jani)
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
[Jani: fixed a couple of checkpatch warnings.]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
This patch removes 5.4Gbps from supported link rate for CHV since
it is not supported in it.
v2: change the ordering for better readability (Ville)
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
This reverts
commit fe51bfb95c996733150c44d21e1c9f4b6322a326.
Author: Ville Syrjälä <ville.syrjala@linux.intel.com>
Date: Thu Mar 12 17:10:38 2015 +0200
CHV does not support intermediate frequencies so reverting the
patch that added it in the first place
Cc: stable@vger.kernel.org # v4.1+
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|