Age | Commit message (Collapse) | Author |
|
[ Upstream commit 7f5ebf5dae42e710162f1c481ebcf28ab7b741c7 ]
RAVB doesn't need mdiobus suspend/resume, that's why it sets
'mac_managed_pm'. However, setting it needs to be moved from init to
probe, so mdiobus PM functions will really never be called (e.g. when
the interface is not up yet during suspend/resume).
Fixes: 4924c0cdce75 ("net: ravb: Fix PHY state warning splat during system resume")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit f3c07758c9007a6bfff5290d9e19d3c41930c897 ]
Since this driver enables the interrupt by RIC2_QFE1, this driver
should clear the interrupt flag if it happens. Otherwise, the interrupt
causes to hang the system.
Note that this also fix a minor coding style (a comment indentation)
around the fixed code.
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
[ Upstream commit c2b6cdee1d13ffbb24baca3c9b8a572d6b541e4e ]
After system entered Suspend to RAM, registers setting of this
hardware is reset because the SoC will be turned off. On R-Car Gen3
(info->ccc_gac), ravb_ptp_init() is called in ravb_probe() only. So,
after system resumed, it lacks of the initial settings for ptp. So,
add ravb_ptp_{init,stop}() into ravb_{resume,suspend}().
Fixes: f5d7837f96e5 ("ravb: ptp: Add CONFIG mode support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
commit c72a7e42592b2e18d862cf120876070947000d7a upstream.
This patch fixes the error "ravb 11c20000.ethernet eth0: failed to switch
device to config mode" during unbind.
We are doing register access after pm_runtime_put_sync().
We usually do cleanup in reverse order of init. Currently in
remove(), the "pm_runtime_put_sync" is not in reverse order.
Probe
reset_control_deassert(rstc);
pm_runtime_enable(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
remove
pm_runtime_put_sync(&pdev->dev);
unregister_netdev(ndev);
..
ravb_mdio_release(priv);
pm_runtime_disable(&pdev->dev);
Consider the call to unregister_netdev()
unregister_netdev->unregister_netdevice_queue->rollback_registered_many
that calls the below functions which access the registers after
pm_runtime_put_sync()
1) ravb_get_stats
2) ravb_close
Fixes: c156633f1353 ("Renesas Ethernet AVB driver proper")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20221214105118.2495313-1-biju.das.jz@bp.renesas.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The skb is delivered to napi_gro_receive() which may free it, after calling this,
dereferencing skb may trigger use-after-free.
Fixes: 1c59eb678cbd ("ravb: Fillup ravb_rx_gbeth() stub")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20221203092941.10880-1-yuehaibing@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
After system resumed on some environment board, the promiscuous mode
is disabled because the SoC turned off. So, call ravb_set_rx_mode() in
the ravb_resume() to fix the issue.
Reported-by: Tho Vu <tho.vu.wh@renesas.com>
Fixes: 0184165b2f42 ("ravb: add sleep PM suspend/resume support")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20221128065604.1864391-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We tell driver developers to always pass NAPI_POLL_WEIGHT
as the weight to netif_napi_add(). This may be confusing
to newcomers, drop the weight argument, those who really
need to tweak the weight can use netif_napi_add_weight().
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN
Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
drivers/net/ethernet/freescale/fec.h
7b15515fc1ca ("Revert "fec: Restart PPS after link state change"")
40c79ce13b03 ("net: fec: add stop mode support for imx8 platform")
https://lore.kernel.org/all/20220921105337.62b41047@canb.auug.org.au/
drivers/pinctrl/pinctrl-ocelot.c
c297561bc98a ("pinctrl: ocelot: Fix interrupt controller")
181f604b33cd ("pinctrl: ocelot: add ability to be used in a non-mmio configuration")
https://lore.kernel.org/all/20220921110032.7cd28114@canb.auug.org.au/
tools/testing/selftests/drivers/net/bonding/Makefile
bbb774d921e2 ("net: Add tests for bonding and team address list management")
152e8ec77640 ("selftests/bonding: add a test for bonding lladdr target")
https://lore.kernel.org/all/20220921110437.5b7dbd82@canb.auug.org.au/
drivers/net/can/usb/gs_usb.c
5440428b3da6 ("can: gs_usb: gs_can_open(): fix race dev->can.state condition")
45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support")
https://lore.kernel.org/all/84f45a7d-92b6-4dc5-d7a1-072152fab6ff@tessares.net/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since commit 744d23c71af39c7d ("net: phy: Warn about incorrect
mdio_bus_phy_resume() state"), a warning splat is printed during system
resume with Wake-on-LAN disabled:
WARNING: CPU: 0 PID: 1197 at drivers/net/phy/phy_device.c:323 mdio_bus_phy_resume+0xbc/0xc8
As the Renesas Ethernet AVB driver already calls phy_{stop,start}() in
its suspend/resume callbacks, it is sufficient to just mark the MAC
responsible for managing the power state of the PHY.
Fixes: fba863b816049b03 ("net: phy: make PHY PM ops a no-op if MAC driver manages PHY PM")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/8ec796f47620980fdd0403e21bd8b7200b4fa1d4.1663598796.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
EMAC IP found on RZ/G2L Gb ethernet supports MII interface.
This patch adds support for selecting MII interface mode.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/20220914192604.265859-1-biju.das.jz@bp.renesas.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for the Renesas Ethernet AVB (EtherAVB-IF) blocks on R-Car
Gen4 SoCs (e.g. R-Car V4H) by matching on a family-specific compatible
value.
These are treated the same as EtherAVB on R-Car Gen3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/2ee968890feba777e627d781128b074b2c43cddb.1662718171.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
RZ/V2M Ethernet is very similar to R-Car Gen3 Ethernet-AVB, though
some small parts are the same as R-Car Gen2.
Other differences to R-Car Gen3 and Gen2 are:
* It has separate data (DI), error (Line 1) and management (Line 2) irqs
rather than one irq for all three.
* Instead of using the High-speed peripheral bus clock for gPTP, it has a
separate gPTP reference clock.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RZ/V2M has a separate gPTP reference clock that is used when the
AVB-DMAC Mode Register (CCC) gPTP Clock Select (CSEL) bits are
set to "01: High-speed peripheral bus clock".
Therefore, add a feature that allows this clock to be used for
gPTP.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
R-Car has a combined interrupt line, ch22 = Line0_DiA | Line1_A | Line2_A.
RZ/V2M has separate interrupt lines for each of these, so add a feature
that allows the driver to get these interrupts and call the common handler.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when the HW has a single interrupt, the driver uses the
GIC, TIC, RIC0 registers to enable and disable interrupts.
When the HW has multiple interrupts, it uses the GIE, GID, TIE, TID,
RIE0, RID0 registers.
However, other devices, e.g. RZ/V2M, have multiple irqs and only have
the GIC, TIC, RIC0 registers.
Therefore, split this into a separate feature.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'max_rx_len' can be up to GBETH_RX_BUFF_MAX (i.e. 8192) (see
'gbeth_hw_info').
The default value of 'num_rx_ring' can be BE_RX_RING_SIZE (i.e. 1024).
So this loop can allocate 8 Mo of memory.
Previous memory allocations in this function already use GFP_KERNEL, so
use __netdev_alloc_skb() and an explicit GFP_KERNEL instead of a
implicit GFP_ATOMIC.
This gives more opportunities of successful allocation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ravb_close() always returns 0, hence the check in ravb_wol_restore() is
pointless (however, we cannot change the prototype of ravb_close() as it
implements the driver's ndo_stop() method).
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After following the call tree of phy_set_max_speed(), it became clear
that this function never returns anything but 0, so we can change its
result type to *void* and drop the result checks from the three drivers
that actually bothered to do it...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 94dd016ae538 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
do_div() does a 64-by-32 division. Here the divisor is an
unsigned long which on some platforms is 64 bit wide. So use
div64_ul instead of do_div to avoid a possible truncation.
Eliminate the following coccicheck warning:
./drivers/net/ethernet/renesas/ravb_main.c:2492:1-7: WARNING:
do_div() does a 64-by-32 division, please consider using div64_ul
instead.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Link: https://lore.kernel.org/r/1637228883-100100-1-git-send-email-yang.lee@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Break the address up into an array on the stack, then call
eth_hw_addr_set().
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the typo AVB->DMAC in comment, as the code following the comment
is for DMAC on Gigabit Ethernet IP.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch enables Receive/Transmit port of TOE and removes
the setting of promiscuous bit from EMAC configuration mode register.
This patch also update EMAC configuration mode comment from
"PAUSE prohibition" to "EMAC Mode: PAUSE prohibition; Duplex; TX;
RX; CRC Pass Through".
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rename the feature bit "nc_queue" with "nc_queues" as AVB DMAC has
RX and TX NC queues.
There is no functional change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Optimize CXR31 register initialization on ravb_emac_init_gbeth
function.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rename the variable "tsrq" with "tccr_mask" as we are passing
TCCR mask to the ravb_wait() function.
There is no functional change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for retrieving stats information for GbEthernet.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
RZ/G2L E-MAC supports carrier counters.
Add a carrier_counter hw feature bit to struct ravb_hw_info
to add this feature only for RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fillup ravb_rx_gbeth() function to support RZ/G2L.
This patch also renames ravb_rcar_rx to ravb_rx_rcar to be
consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fillup ravb_rx_ring_format_gbeth() function to support RZ/G2L.
This patch also renames ravb_rx_ring_format to ravb_rx_ring_format_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fillup ravb_rx_ring_free_gbeth() function to support RZ/G2L.
This patch also renames ravb_rx_ring_free to ravb_rx_ring_free_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fillup ravb_alloc_rx_desc_gbeth() function to support RZ/G2L.
This patch also renames ravb_alloc_rx_desc to ravb_alloc_rx_desc_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
R-Car AVB-DMAC has maximum 2K size on RX buffer, whereas on RZ/G2L
it is 8K. We need to allow for changing the MTU within the limit
of the maximum size of a descriptor.
Add a rx_max_buf_size variable to struct ravb_hw_info to handle
this difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use ALIGN macro for calculating the value for max_rx_len.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use the new of_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- of_get_mac_address(np, dev->dev_addr)
+ of_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize GbEthernet E-MAC found on RZ/G2L SoC.
This patch also renames ravb_set_rate to ravb_set_rate_rcar and
ravb_rcar_emac_init to ravb_emac_init_rcar to be consistent with
the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RZ/G2L supports half duplex mode.
Add a half_duplex hw feature bit to struct ravb_hw_info for
supporting half duplex mode for RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
E-MAC on R-Car supports magic packet detection, whereas RZ/G2L
does not support this feature. Add magic_pkt to struct ravb_hw_info
and enable this feature only for R-Car.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
R-Car AVB-DMAC has 4 Transmit start request queues, whereas
RZ/G2L has only 1 Transmit start request queue.
Add a tsrq variable to struct ravb_hw_info to handle this
difference.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
R-Car supports gPTP feature whereas RZ/G2L does not support it.
This patch excludes gtp feature support for RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize GbEthernet DMAC found on RZ/G2L SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RZ/G2L SoC has Gigabit Ethernet IP consisting of Ethernet controller
(E-MAC), Internal TCP/IP Offload Engine (TOE) and Dedicated Direct
memory access controller (DMAC).
This patch adds compatible string for RZ/G2L and fills up the
ravb_hw_info struct. Function stubs are added which will be used by
gbeth_hw_info and will be filled incrementally.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
R-Car supports network control queue whereas RZ/G2L does not support
it. Add nc_queue to struct ravb_hw_info, so that NC queue is handled
only by R-Car.
This patch also renames ravb_rcar_dmac_init to ravb_dmac_init_rcar
to be consistent with the naming convention used in sh_eth driver.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the variable "no_ptp_cfg_active" with "gptp" and
"ptp_cfg_active" with "ccc_gac" to match the HW features.
There is no functional change.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename "ravb_set_features_rx_csum" function to "ravb_set_features_rcar" and
replace the function pointer "set_rx_csum_feature" with "set_feature".
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reset support is present on R-Car. Let's support it, if it is
available.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The E-MAC IP on the R-Car AVB module has different initialization
parameters for RX frame size, duplex settings, different offset
for transfer speed setting and has magic packet detection support
compared to E-MAC on RZ/G2L Gigabit Ethernet module. Factorise
the ravb_emac_init function to support the later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DMAC IP on the R-Car AVB module has different initialization
parameters for RCR, TGC, TCCR, RIC0, RIC2, and TIC compared to
DMAC IP on the RZ/G2L Gigabit Ethernet module. Factorise the
ravb_dmac_init function to support the later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RZ/G2L supports HW checksum on RX and TX whereas R-Car supports on RX.
Factorise ravb_set_features to support this feature.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|