| Age | Commit message (Collapse) | Author |
|---|
|
Add a dependency on CONFIG_MMU to ofdrm. The driver uses GEM SHMEM
helpers, which require MMU support. A reported error message [1] is
shown below.
arm-linux-gnueabi-ld: drivers/gpu/drm/drm_gem_shmem_helper.o: in function `drm_gem_shmem_fault':
>> drivers/gpu/drm/drm_gem_shmem_helper.c:562: undefined reference to `vmf_insert_pfn'
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Fixes: c8a17756c425 ("drm/ofdrm: Add ofdrm for Open Firmware framebuffers")
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: Danilo Krummrich <dakr@redhat.com>
Cc: Michal Suchanek <msuchanek@suse.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://lore.kernel.org/dri-devel/202210192029.ZFeJvqjv-lkp@intel.com/ # [1]
Link: https://patchwork.freedesktop.org/patch/msgid/20221101104049.15601-1-tzimmermann@suse.de
|
|
Open Firmware provides basic display output via the 'display' node.
DT platform code already provides a device that represents the node's
framebuffer. Add a DRM driver for the device. The display mode and
color format is pre-initialized by the system's firmware. Runtime
modesetting via DRM is not possible. The display is useful during
early boot stages or as error fallback.
Similar functionality is already provided by fbdev's offb driver,
which is insufficient for modern userspace. The old driver includes
support for BootX device tree, which can be found on old 32-bit
PowerPC Macintosh systems. If these are still in use, the
functionality can be added to ofdrm or implemented in a new
driver. As with simpledrm, the fbdev driver cannot be selected if
ofdrm is already enabled.
Two notable points about the driver:
* Reading the framebuffer aperture from the device tree is not
reliable on all systems. Ofdrm takes the heuristics and a comment
from offb to pick the correct range.
* No resource management may be tied to the underlying PCI device.
Otherwise the handover to the native driver will fail with a resource
conflict. PCI management is therefore done as part of the platform
device's cleanup.
The driver has been tested on qemu's ppc64le emulation. The device
hand-over has been tested with bochs.
v5:
* use drm_atomic_helper_check_crtc_primary_plane()
v4:
* set preferred depth to the correct value
* set bpp value for console emulation
* output scanout-buffer parameters with drm_dbg()
v3:
* reintegrate FWFB helpers into ofdrm
* use damage iterator
* sync GEM BOs with drm_gem_fb_{begin,end}_cpu_access()
* fix various atomic_check helpers
* remove CRTC atomic_{enable,disable} (Javier)
* compute stride with drm_format_info_min_pitch() (Daniel)
v2:
* removed simple-pipe helpers
* built driver on top of FWFB helpers
* merged all init code into single function
* make PCI support optional (Michal)
* support COMPILE_TEST (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
convert
Link: https://patchwork.freedesktop.org/patch/msgid/20221011150712.3928-2-tzimmermann@suse.de
|
|
Rename "GEM CMA" helpers to "GEM DMA" helpers - considering the
hierarchy of APIs (mm/cma -> dma -> gem dma) calling them "GEM
DMA" seems to be more applicable.
Besides that, commit e57924d4ae80 ("drm/doc: Task to rename CMA helpers")
requests to rename the CMA helpers and implies that people seem to be
confused about the naming.
In order to do this renaming the following script was used:
```
#!/bin/bash
DIRS="drivers/gpu include/drm Documentation/gpu"
REGEX_SYM_UPPER="[0-9A-Z_\-]"
REGEX_SYM_LOWER="[0-9a-z_\-]"
REGEX_GREP_UPPER="(${REGEX_SYM_UPPER}*)(GEM)_CMA_(${REGEX_SYM_UPPER}*)"
REGEX_GREP_LOWER="(${REGEX_SYM_LOWER}*)(gem)_cma_(${REGEX_SYM_LOWER}*)"
REGEX_SED_UPPER="s/${REGEX_GREP_UPPER}/\1\2_DMA_\3/g"
REGEX_SED_LOWER="s/${REGEX_GREP_LOWER}/\1\2_dma_\3/g"
# Find all upper case 'CMA' symbols and replace them with 'DMA'.
for ff in $(grep -REHl "${REGEX_GREP_UPPER}" $DIRS)
do
sed -i -E "$REGEX_SED_UPPER" $ff
done
# Find all lower case 'cma' symbols and replace them with 'dma'.
for ff in $(grep -REHl "${REGEX_GREP_LOWER}" $DIRS)
do
sed -i -E "$REGEX_SED_LOWER" $ff
done
# Replace all occurrences of 'CMA' / 'cma' in comments and
# documentation files with 'DMA' / 'dma'.
for ff in $(grep -RiHl " cma " $DIRS)
do
sed -i -E "s/ cma / dma /g" $ff
sed -i -E "s/ CMA / DMA /g" $ff
done
# Rename all 'cma_obj's to 'dma_obj'.
for ff in $(grep -RiHl "cma_obj" $DIRS)
do
sed -i -E "s/cma_obj/dma_obj/g" $ff
done
```
Only a few more manual modifications were needed, e.g. reverting the
following modifications in some DRM Kconfig files
- select CMA if HAVE_DMA_CONTIGUOUS
+ select DMA if HAVE_DMA_CONTIGUOUS
as well as manually picking the occurrences of 'CMA'/'cma' in comments and
documentation which relate to "GEM CMA", but not "FB CMA".
Also drivers/gpu/drm/Makefile was fixed up manually after renaming
drm_gem_cma_helper.c to drm_gem_dma_helper.c.
This patch is compile-time tested building a x86_64 kernel with
`make allyesconfig && make drivers/gpu/drm`.
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Danilo Krummrich <dakr@redhat.com>
Reviewed-by: Liviu Dudau <liviu.dudau@arm.com> #drivers/gpu/drm/arm
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220802000405.949236-4-dakr@redhat.com
|
|
Implement DRM's aperture helpers under video/ for sharing with other
sub-systems. Remove DRM-isms from the interface. The helpers track
the ownership of framebuffer apertures and provide hand-over from
firmware, such as EFI and VESA, to native graphics drivers.
Other subsystems, such as fbdev and vfio, also have to maintain ownership
of framebuffer apertures. Moving DRM's aperture helpers to a more public
location allows all subsystems to interact with each other and share a
common implementation.
The aperture helpers are selected by the various firmware drivers within
DRM and fbdev, and the VGA text-console driver.
The original DRM interface is kept in place for use by DRM drivers.
v3:
* prefix all interfaces with aperture_ (Javier)
* rework and simplify documentation (Javier)
* rename struct dev_aperture to struct aperture_range
* rebase onto latest DRM
* update MAINTAINERS entry
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Laszlo Ersek <lersek@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220622140134.12763-3-tzimmermann@suse.de
|
|
Add a driver that will work with most MIPI DBI compatible SPI panels.
This avoids adding a driver for every new MIPI DBI compatible controller
that is to be used by Linux. The 'compatible' Device Tree property with
a '.bin' suffix will be used to load a firmware file that contains the
controller configuration.
Example (driver will load sainsmart18.bin):
display@0 {
compatible = "sainsmart18", "panel-mipi-dbi-spi";
...
};
v5:
- kconfig: s/DRM_KMS_CMA_HELPER/DRM_GEM_CMA_HELPER/ (Sam)
- kconfig: Add select VIDEOMODE_HELPERS (Sam)
- kconfig: Add wiki url in the description (Sam)
- Split out and use of_get_drm_panel_display_mode()(Sam)
- Only use the first compatible to look for a firmware file since the
binding mandates 2 compatibles.
- Make having a firmware file mandatory so we can print an error
message if it's missing to improve the user experience. It's very
unlikely that a controller doesn't need to be initialized and if
it doesn't, it's possible to have a firmware file containing only
a DCS NOP.
v4:
- Move driver to drm/tiny where the other drivers of its kind are located.
The driver module will not be shared with a future DPI driver after all.
v3:
- Move properties to DT (Maxime)
- The MIPI DPI spec has optional support for DPI where the controller is
configured over DBI. Rework the command functions so they can be moved
to drm_mipi_dbi and shared with a future panel-mipi-dpi-spi driver
v2:
- Drop model property and use compatible instead (Rob)
- Add wiki entry in MAINTAINERS
Acked-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220227124713.39766-6-noralf@tronnes.org
|
|
Link drm_fb_cma_helper.o into drm_cma_helper.ko if CONFIG_DRM_KMS_HELPER
has been set. Remove CONFIG_DRM_KMS_CMA_HELPER config option. Selecting
KMS helpers and CMA will now automatically enable CMA KMS helpers.
Some drivers' Kconfig files did not correctly select KMS or CMA helpers.
Fix this as part of the change.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20211106193509.17472-3-tzimmermann@suse.de
|
|
This patch adds support for Newhaven's NHD-1.8-128160EF display, featuring
an Ilitek ILI9163 controller.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015150131.1020878-3-daniel@zonque.org
|
|
We want to stop gup, which isn't the case if we use vmf_insert_page
and VM_MIXEDMAP, because that does not set pte_special.
The motivation here is to stop get_user_pages from working on buffer
object mmaps in general. Quoting some discussion with Thomas:
On Thu, Jul 22, 2021 at 08:22:43PM +0200, Thomas Zimmermann wrote:
> Am 13.07.21 um 22:51 schrieb Daniel Vetter:
> > We want to stop gup, which isn't the case if we use vmf_insert_page
>
> What is gup?
get_user_pages. It pins memory wherever it is, which badly wreaks at least
ttm and could also cause trouble with cma allocations. In both cases
becaue we can't move/reuse these pages anymore.
Now get_user_pages fails when the memory isn't considered "normal", like
with VM_PFNMAP and using vm_insert_pfn. For consistency across all dma-buf
I'm trying (together with Christian König) to roll this out everywhere,
for fewer surprises.
E.g. for 5.14 iirc we merged a patch to do the same for ttm, where it
closes an actual bug (ttm gets really badly confused when there's suddenly
pinned pages where it thought it can move them).
cma allcoations already use VM_PFNMAP (because that's what dma_mmap is
using underneath), as is anything that's using remap_pfn_range. Worst case
we have to revert this patch for shmem helpers if it breaks something, but
I hope that's not the case. On the ttm side we've also had some fallout
that we needed to paper over with clever tricks.
v2: With this shmem gem helpers now definitely need CONFIG_MMU (0day)
v3: add more depends on MMU. For usb drivers this is a bit awkward,
but really it's correct: To be able to provide a contig mapping of
buffers to userspace on !MMU platforms we'd need to use the cma
helpers for these drivers on those platforms. As-is this wont work.
Also not exactly sure why vm_insert_page doesn't go boom, because that
definitely wont fly in practice since the pages are non-contig to
begin with.
v4: Explain the entire motivation a lot more (Thomas)
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210812131412.2487363-2-daniel.vetter@ffwll.ch
|
|
The register_gop_device() function registers an "efi-framebuffer" platform
device to match against the efifb driver, to have an early framebuffer for
EFI platforms.
But there is already support to do exactly the same by the Generic System
Framebuffers (sysfb) driver. This used to be only for X86 but it has been
moved to drivers/firmware and could be reused by other architectures.
Also, besides supporting registering an "efi-framebuffer", this driver can
register a "simple-framebuffer" allowing to use the siple{fb,drm} drivers
on non-X86 EFI platforms. For example, on aarch64 these drivers can only
be used with DT and doesn't have code to register a "simple-frambuffer"
platform device when booting with EFI.
For these reasons, let's remove the register_gop_device() duplicated code
and instead move the platform specific logic that's there to sysfb driver.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Borislav Petkov <bp@suse.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20210625131359.1804394-1-javierm@redhat.com
|
|
The bochs driver is only ~600 lines of code. Putting it into tiny/
cleans up the DRM directory slightly. Some style problems were fixed
and unneeded include statements were removed. No functional changes.
v2:
* make bochs_mode_funcs static (Daniel, kernel test robot)
* rebase onto aperture API changes
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210702075434.27677-2-tzimmermann@suse.de
|
|
The simpledrm driver is a DRM driver for simple-framebuffer framebuffers
as provided by the kernel's boot code. This driver enables basic
graphical output on many different graphics devices that are provided
by the platform (e.g., EFI, VESA, embedded framebuffers).
With the kernel's simple-framebuffer infrastructure, the kernel receives
a pre-configured framebuffer from the system (i.e., firmware, boot
loader). It creates a platform device to which simpledrm attaches.
The system's framebuffer consists of a memory range, size and format.
Based on these values, simpledrm creates a DRM devices. No actual
modesetting is possible.
A firmware framebuffer might also be specified via device-tree files. If
no device platform data is given, try the DT device node.
Make sure required hardware clocks and regulators are enabled while the
firmware framebuffer is in use. The basic code has been taken from the
simplefb driver and adapted to DRM. Clocks are released automatically
via devres helpers.
The drivers displays a console on simpledrm's framebuffer. The default
framebuffer format is being used.
v4:
* disable simplefb if simpledrm has been selected (Maxime)
v3:
* add disable function that clears screen to black (Daniel)
* set shadow buffering only for fbdev emulation
* set platform-driver data during device creation
v2:
* rename driver to simpledrm
* add dri-devel to MAINTAINERS entry
* put native format first in primary-plane format list (Daniel)
* inline simplekms_device_cleanup() (Daniel)
* use helpers for shadow-buffered planes
* fix whitespace errors
* add Device Tree match table
* clean-up parser wrappers
* use strscpy()
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> # fbdev support
Acked-by: Maxime Ripard <maxime@cerno.tech>
Tested-by: nerdopolis <bluescreen_avenger@verizon.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20210430105840.30515-5-tzimmermann@suse.de
Link: https://patchwork.freedesktop.org/patch/msgid/20210430105840.30515-6-tzimmermann@suse.de
Link: https://patchwork.freedesktop.org/patch/msgid/20210430105840.30515-7-tzimmermann@suse.de
Link: https://patchwork.freedesktop.org/patch/msgid/20210430105840.30515-8-tzimmermann@suse.de
Link: https://patchwork.freedesktop.org/patch/msgid/20210430105840.30515-9-tzimmermann@suse.de
|
|
Because it is.
v2: Delete now unused crtc funcs (0day)
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210112084358.2771527-15-daniel.vetter@ffwll.ch
|
|
Because it is. Huge congrats to everyone who made this kind of
refactoring happen!
Acked-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Link: https://patchwork.freedesktop.org/patch/msgid/20200415074034.175360-38-daniel.vetter@ffwll.ch
|
|
This adds support fot ilitek,ili9486 based displays with shift register
in front of controller.
Ozzmaker,Piscreen and Waveshare,rpi-lcd-35 are such displays.
Acked-by: Sam Ravnborg <sam@ravnborg.org> (v4)
Reviewed-by: Noralf Tronnes <noralf@tronnes.org> (v4)
Signed-off-by: Kamlesh Gurudasani <kamlesh.gurudasani@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
[fixed checkpatch warnings]
Link: https://patchwork.freedesktop.org/patch/msgid/a9c8065c3ef7707650630b3b21a0c01d725fc5a0.1581270802.git.kamlesh.gurudasani@gmail.com
|
|
Add support for the Okaya RH128128T display to the st7735r driver on
DT-enabled systems.
The RH128128T is a 128x128 1.44" TFT display driven by a Sitronix
ST7715R TFT Controller/Driver. The latter is very similar to the
ST7735R, and can be handled by the existing st7735r driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20200115124548.3951-6-geert+renesas@glider.be
|
|
Commit 554b3529fe01 ("thermal/drivers/core: Remove the module Kconfig's
option") changed the type of THERMAL from tristate to bool, so
THERMAL || !THERMAL is now always y. Remove the redundant dependency.
Discovered through Kconfiglib detecting a dependency loop. The C tools
simplify the expression to y before running dependency loop detection,
and so don't see it. Changing the type of THERMAL back to tristate makes
the C tools detect the same loop.
Not sure if running dep. loop detection after simplification can be
called a bug. Fixing this nit unbreaks Kconfiglib on the kernel at
least.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20190927174218.GA32085@huvuddator
|
|
Move the driver to the new haven for tiny DRM drivers.
Cc: Hans de Goede <hdegoede@redhat.com>
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190725105132.22545-4-noralf@tronnes.org
|
|
The drm in tinydrm is superfluous so rename to tiny.
Suggested-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190725105132.22545-3-noralf@tronnes.org
|