| Age | Commit message (Collapse) | Author |
|---|
|
The mainline vf610_adc driver never used this property.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The micro-SD card doesn't feature a write-protect pin. Set the
corresponding property in the devicetree to handle this behavior
correctly and suppress driver warnings.
Signed-off-by: Yunus Bas <y.bas@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PHYTEC PEB-AV-02 adapter adds the capability to connect a parallel
LCD display to the phyBOARD-Segin full featured, either with capacitive
or resistive touch.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The touchscreen subnode name needs to be stmpe_touchscreen as mentioned
in the dt-bindings.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The conversion of the spi-imx driver to use GPIO descriptors
in commit 8cdcd8aeee28 ("spi: imx/fsl-lpspi: Convert to GPIO descriptors")
helped to detect the following SPI chipselect polarity mismatch on an
imx6q-sabresd:
[ 4.854337] m25p80@0 enforce active low on chipselect handle
Prior to the above commit, the chipselect polarity passed via cs-gpios
property was ignored and considered active-low.
The reason for such mismatch is clearly explained in the comments inside
drivers/gpio/gpiolib-of.c:
* SPI children have active low chip selects
* by default. This can be specified negatively
* by just omitting "spi-cs-high" in the
* device node, or actively by tagging on
* GPIO_ACTIVE_LOW as flag in the device
* tree. If the line is simultaneously
* tagged as active low in the device tree
* and has the "spi-cs-high" set, we get a
* conflict and the "spi-cs-high" flag will
* take precedence.
To properly represent the SPI chipselect polarity, change it to active-low
when the "spi-cs-high" property is absent.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The ECSPI interface is available on the expansion connector of every
PHYTEC phyBOARD-Segin. Move its definition to the board include file
for better reuse.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
To disable Ethernet interfaces in case they are not populated
make the FEC and Ethernet PHY status configurable in the dts files.
Also change the Ethernet PHYs labels to make them correspond to
the MDIO address.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Reduce the drive strength for the MDC, MDIO and TX pins of FEC1 and FEC2
on the phyBOARD-Segin to improve signal quality and EMC. Also disable
internal pull-ups on the MDC and MDIO pins.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Use the same name scheme for the phyBOARD-Segin and the phyCORE-i.MX
6UL as is used for the PHYTEC phyBOARD-Mira and phyCORE-i.MX 6.
This is only a cosmetic change and there is no functional change
intended.
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|