diff options
Diffstat (limited to 'drivers/usb/gadget/udc/mv_udc.h')
| -rw-r--r-- | drivers/usb/gadget/udc/mv_udc.h | 313 |
1 files changed, 313 insertions, 0 deletions
diff --git a/drivers/usb/gadget/udc/mv_udc.h b/drivers/usb/gadget/udc/mv_udc.h new file mode 100644 index 000000000000..be77f207dbaf --- /dev/null +++ b/drivers/usb/gadget/udc/mv_udc.h @@ -0,0 +1,313 @@ +/* + * Copyright (C) 2011 Marvell International Ltd. All rights reserved. + * + * This program is free software; you can redistribute it and/or modify it + * under the terms of the GNU General Public License as published by the + * Free Software Foundation; either version 2 of the License, or (at your + * option) any later version. + */ + +#ifndef __MV_UDC_H +#define __MV_UDC_H + +#define VUSBHS_MAX_PORTS 8 + +#define DQH_ALIGNMENT 2048 +#define DTD_ALIGNMENT 64 +#define DMA_BOUNDARY 4096 + +#define EP_DIR_IN 1 +#define EP_DIR_OUT 0 + +#define DMA_ADDR_INVALID (~(dma_addr_t)0) + +#define EP0_MAX_PKT_SIZE 64 +/* ep0 transfer state */ +#define WAIT_FOR_SETUP 0 +#define DATA_STATE_XMIT 1 +#define DATA_STATE_NEED_ZLP 2 +#define WAIT_FOR_OUT_STATUS 3 +#define DATA_STATE_RECV 4 + +#define CAPLENGTH_MASK (0xff) +#define DCCPARAMS_DEN_MASK (0x1f) + +#define HCSPARAMS_PPC (0x10) + +/* Frame Index Register Bit Masks */ +#define USB_FRINDEX_MASKS 0x3fff + +/* Command Register Bit Masks */ +#define USBCMD_RUN_STOP (0x00000001) +#define USBCMD_CTRL_RESET (0x00000002) +#define USBCMD_SETUP_TRIPWIRE_SET (0x00002000) +#define USBCMD_SETUP_TRIPWIRE_CLEAR (~USBCMD_SETUP_TRIPWIRE_SET) + +#define USBCMD_ATDTW_TRIPWIRE_SET (0x00004000) +#define USBCMD_ATDTW_TRIPWIRE_CLEAR (~USBCMD_ATDTW_TRIPWIRE_SET) + +/* bit 15,3,2 are for frame list size */ +#define USBCMD_FRAME_SIZE_1024 (0x00000000) /* 000 */ +#define USBCMD_FRAME_SIZE_512 (0x00000004) /* 001 */ +#define USBCMD_FRAME_SIZE_256 (0x00000008) /* 010 */ +#define USBCMD_FRAME_SIZE_128 (0x0000000C) /* 011 */ +#define USBCMD_FRAME_SIZE_64 (0x00008000) /* 100 */ +#define USBCMD_FRAME_SIZE_32 (0x00008004) /* 101 */ +#define USBCMD_FRAME_SIZE_16 (0x00008008) /* 110 */ +#define USBCMD_FRAME_SIZE_8 (0x0000800C) /* 111 */ + +#define EPCTRL_TX_ALL_MASK (0xFFFF0000) +#define EPCTRL_RX_ALL_MASK (0x0000FFFF) + +#define EPCTRL_TX_DATA_TOGGLE_RST (0x00400000) +#define EPCTRL_TX_EP_STALL (0x00010000) +#define EPCTRL_RX_EP_STALL (0x00000001) +#define EPCTRL_RX_DATA_TOGGLE_RST (0x00000040) +#define EPCTRL_RX_ENABLE (0x00000080) +#define EPCTRL_TX_ENABLE (0x00800000) +#define EPCTRL_CONTROL (0x00000000) +#define EPCTRL_ISOCHRONOUS (0x00040000) +#define EPCTRL_BULK (0x00080000) +#define EPCTRL_INT (0x000C0000) +#define EPCTRL_TX_TYPE (0x000C0000) +#define EPCTRL_RX_TYPE (0x0000000C) +#define EPCTRL_DATA_TOGGLE_INHIBIT (0x00000020) +#define EPCTRL_TX_EP_TYPE_SHIFT (18) +#define EPCTRL_RX_EP_TYPE_SHIFT (2) + +#define EPCOMPLETE_MAX_ENDPOINTS (16) + +/* endpoint list address bit masks */ +#define USB_EP_LIST_ADDRESS_MASK 0xfffff800 + +#define PORTSCX_W1C_BITS 0x2a +#define PORTSCX_PORT_RESET 0x00000100 +#define PORTSCX_PORT_POWER 0x00001000 +#define PORTSCX_FORCE_FULL_SPEED_CONNECT 0x01000000 +#define PORTSCX_PAR_XCVR_SELECT 0xC0000000 +#define PORTSCX_PORT_FORCE_RESUME 0x00000040 +#define PORTSCX_PORT_SUSPEND 0x00000080 +#define PORTSCX_PORT_SPEED_FULL 0x00000000 +#define PORTSCX_PORT_SPEED_LOW 0x04000000 +#define PORTSCX_PORT_SPEED_HIGH 0x08000000 +#define PORTSCX_PORT_SPEED_MASK 0x0C000000 + +/* USB MODE Register Bit Masks */ +#define USBMODE_CTRL_MODE_IDLE 0x00000000 +#define USBMODE_CTRL_MODE_DEVICE 0x00000002 +#define USBMODE_CTRL_MODE_HOST 0x00000003 +#define USBMODE_CTRL_MODE_RSV 0x00000001 +#define USBMODE_SETUP_LOCK_OFF 0x00000008 +#define USBMODE_STREAM_DISABLE 0x00000010 + +/* USB STS Register Bit Masks */ +#define USBSTS_INT 0x00000001 +#define USBSTS_ERR 0x00000002 +#define USBSTS_PORT_CHANGE 0x00000004 +#define USBSTS_FRM_LST_ROLL 0x00000008 +#define USBSTS_SYS_ERR 0x00000010 +#define USBSTS_IAA 0x00000020 +#define USBSTS_RESET 0x00000040 +#define USBSTS_SOF 0x00000080 +#define USBSTS_SUSPEND 0x00000100 +#define USBSTS_HC_HALTED 0x00001000 +#define USBSTS_RCL 0x00002000 +#define USBSTS_PERIODIC_SCHEDULE 0x00004000 +#define USBSTS_ASYNC_SCHEDULE 0x00008000 + + +/* Interrupt Enable Register Bit Masks */ +#define USBINTR_INT_EN (0x00000001) +#define USBINTR_ERR_INT_EN (0x00000002) +#define USBINTR_PORT_CHANGE_DETECT_EN (0x00000004) + +#define USBINTR_ASYNC_ADV_AAE (0x00000020) +#define USBINTR_ASYNC_ADV_AAE_ENABLE (0x00000020) +#define USBINTR_ASYNC_ADV_AAE_DISABLE (0xFFFFFFDF) + +#define USBINTR_RESET_EN (0x00000040) +#define USBINTR_SOF_UFRAME_EN (0x00000080) +#define USBINTR_DEVICE_SUSPEND (0x00000100) + +#define USB_DEVICE_ADDRESS_MASK (0xfe000000) +#define USB_DEVICE_ADDRESS_BIT_SHIFT (25) + +struct mv_cap_regs { + u32 caplength_hciversion; + u32 hcsparams; /* HC structural parameters */ + u32 hccparams; /* HC Capability Parameters*/ + u32 reserved[5]; + u32 dciversion; /* DC version number and reserved 16 bits */ + u32 dccparams; /* DC Capability Parameters */ +}; + +struct mv_op_regs { + u32 usbcmd; /* Command register */ + u32 usbsts; /* Status register */ + u32 usbintr; /* Interrupt enable */ + u32 frindex; /* Frame index */ + u32 reserved1[1]; + u32 deviceaddr; /* Device Address */ + u32 eplistaddr; /* Endpoint List Address */ + u32 ttctrl; /* HOST TT status and control */ + u32 burstsize; /* Programmable Burst Size */ + u32 txfilltuning; /* Host Transmit Pre-Buffer Packet Tuning */ + u32 reserved[4]; + u32 epnak; /* Endpoint NAK */ + u32 epnaken; /* Endpoint NAK Enable */ + u32 configflag; /* Configured Flag register */ + u32 portsc[VUSBHS_MAX_PORTS]; /* Port Status/Control x, x = 1..8 */ + u32 otgsc; + u32 usbmode; /* USB Host/Device mode */ + u32 epsetupstat; /* Endpoint Setup Status */ + u32 epprime; /* Endpoint Initialize */ + u32 epflush; /* Endpoint De-initialize */ + u32 epstatus; /* Endpoint Status */ + u32 epcomplete; /* Endpoint Interrupt On Complete */ + u32 epctrlx[16]; /* Endpoint Control, where x = 0.. 15 */ + u32 mcr; /* Mux Control */ + u32 isr; /* Interrupt Status */ + u32 ier; /* Interrupt Enable */ +}; + +struct mv_udc { + struct usb_gadget gadget; + struct usb_gadget_driver *driver; + spinlock_t lock; + struct completion *done; + struct platform_device *dev; + int irq; + + struct mv_cap_regs __iomem *cap_regs; + struct mv_op_regs __iomem *op_regs; + void __iomem *phy_regs; + unsigned int max_eps; + struct mv_dqh *ep_dqh; + size_t ep_dqh_size; + dma_addr_t ep_dqh_dma; + + struct dma_pool *dtd_pool; + struct mv_ep *eps; + + struct mv_dtd *dtd_head; + struct mv_dtd *dtd_tail; + unsigned int dtd_entries; + + struct mv_req *status_req; + struct usb_ctrlrequest local_setup_buff; + + unsigned int resume_state; /* USB state to resume */ + unsigned int usb_state; /* USB current state */ + unsigned int ep0_state; /* Endpoint zero state */ + unsigned int ep0_dir; + + unsigned int dev_addr; + unsigned int test_mode; + + int errors; + unsigned softconnect:1, + vbus_active:1, + remote_wakeup:1, + softconnected:1, + force_fs:1, + clock_gating:1, + active:1, + stopped:1; /* stop bit is setted */ + + struct work_struct vbus_work; + struct workqueue_struct *qwork; + + struct usb_phy *transceiver; + + struct mv_usb_platform_data *pdata; + + /* some SOC has mutiple clock sources for USB*/ + struct clk *clk; +}; + +/* endpoint data structure */ +struct mv_ep { + struct usb_ep ep; + struct mv_udc *udc; + struct list_head queue; + struct mv_dqh *dqh; + u32 direction; + char name[14]; + unsigned stopped:1, + wedge:1, + ep_type:2, + ep_num:8; +}; + +/* request data structure */ +struct mv_req { + struct usb_request req; + struct mv_dtd *dtd, *head, *tail; + struct mv_ep *ep; + struct list_head queue; + unsigned int test_mode; + unsigned dtd_count; + unsigned mapped:1; +}; + +#define EP_QUEUE_HEAD_MULT_POS 30 +#define EP_QUEUE_HEAD_ZLT_SEL 0x20000000 +#define EP_QUEUE_HEAD_MAX_PKT_LEN_POS 16 +#define EP_QUEUE_HEAD_MAX_PKT_LEN(ep_info) (((ep_info)>>16)&0x07ff) +#define EP_QUEUE_HEAD_IOS 0x00008000 +#define EP_QUEUE_HEAD_NEXT_TERMINATE 0x00000001 +#define EP_QUEUE_HEAD_IOC 0x00008000 +#define EP_QUEUE_HEAD_MULTO 0x00000C00 +#define EP_QUEUE_HEAD_STATUS_HALT 0x00000040 +#define EP_QUEUE_HEAD_STATUS_ACTIVE 0x00000080 +#define EP_QUEUE_CURRENT_OFFSET_MASK 0x00000FFF +#define EP_QUEUE_HEAD_NEXT_POINTER_MASK 0xFFFFFFE0 +#define EP_QUEUE_FRINDEX_MASK 0x000007FF +#define EP_MAX_LENGTH_TRANSFER 0x4000 + +struct mv_dqh { + /* Bits 16..26 Bit 15 is Interrupt On Setup */ + u32 max_packet_length; + u32 curr_dtd_ptr; /* Current dTD Pointer */ + u32 next_dtd_ptr; /* Next dTD Pointer */ + /* Total bytes (16..30), IOC (15), INT (8), STS (0-7) */ + u32 size_ioc_int_sts; + u32 buff_ptr0; /* Buffer pointer Page 0 (12-31) */ + u32 buff_ptr1; /* Buffer pointer Page 1 (12-31) */ + u32 buff_ptr2; /* Buffer pointer Page 2 (12-31) */ + u32 buff_ptr3; /* Buffer pointer Page 3 (12-31) */ + u32 buff_ptr4; /* Buffer pointer Page 4 (12-31) */ + u32 reserved1; + /* 8 bytes of setup data that follows the Setup PID */ + u8 setup_buffer[8]; + u32 reserved2[4]; +}; + + +#define DTD_NEXT_TERMINATE (0x00000001) +#define DTD_IOC (0x00008000) +#define DTD_STATUS_ACTIVE (0x00000080) +#define DTD_STATUS_HALTED (0x00000040) +#define DTD_STATUS_DATA_BUFF_ERR (0x00000020) +#define DTD_STATUS_TRANSACTION_ERR (0x00000008) +#define DTD_RESERVED_FIELDS (0x00007F00) +#define DTD_ERROR_MASK (0x68) +#define DTD_ADDR_MASK (0xFFFFFFE0) +#define DTD_PACKET_SIZE 0x7FFF0000 +#define DTD_LENGTH_BIT_POS (16) + +struct mv_dtd { + u32 dtd_next; + u32 size_ioc_sts; + u32 buff_ptr0; /* Buffer pointer Page 0 */ + u32 buff_ptr1; /* Buffer pointer Page 1 */ + u32 buff_ptr2; /* Buffer pointer Page 2 */ + u32 buff_ptr3; /* Buffer pointer Page 3 */ + u32 buff_ptr4; /* Buffer pointer Page 4 */ + u32 scratch_ptr; + /* 32 bytes */ + dma_addr_t td_dma; /* dma address for this td */ + struct mv_dtd *next_dtd_virt; +}; + +#endif |