diff options
Diffstat (limited to 'drivers/tty/serial')
| -rw-r--r-- | drivers/tty/serial/8250/8250_core.c | 11 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_dw.c | 47 | ||||
| -rw-r--r-- | drivers/tty/serial/8250/8250_pci.c | 20 | ||||
| -rw-r--r-- | drivers/tty/serial/atmel_serial.c | 49 | ||||
| -rw-r--r-- | drivers/tty/serial/of_serial.c | 4 | ||||
| -rw-r--r-- | drivers/tty/serial/sprd_serial.c | 4 |
6 files changed, 98 insertions, 37 deletions
diff --git a/drivers/tty/serial/8250/8250_core.c b/drivers/tty/serial/8250/8250_core.c index e3b9570a1eff..deae122c9c4b 100644 --- a/drivers/tty/serial/8250/8250_core.c +++ b/drivers/tty/serial/8250/8250_core.c @@ -2138,8 +2138,8 @@ int serial8250_do_startup(struct uart_port *port) /* * Clear the interrupt registers. */ - if (serial_port_in(port, UART_LSR) & UART_LSR_DR) - serial_port_in(port, UART_RX); + serial_port_in(port, UART_LSR); + serial_port_in(port, UART_RX); serial_port_in(port, UART_IIR); serial_port_in(port, UART_MSR); @@ -2300,8 +2300,8 @@ dont_test_tx_en: * saved flags to avoid getting false values from polling * routines or the previous session. */ - if (serial_port_in(port, UART_LSR) & UART_LSR_DR) - serial_port_in(port, UART_RX); + serial_port_in(port, UART_LSR); + serial_port_in(port, UART_RX); serial_port_in(port, UART_IIR); serial_port_in(port, UART_MSR); up->lsr_saved_flags = 0; @@ -2394,8 +2394,7 @@ void serial8250_do_shutdown(struct uart_port *port) * Read data port to reset things, and then unlink from * the IRQ chain. */ - if (serial_port_in(port, UART_LSR) & UART_LSR_DR) - serial_port_in(port, UART_RX); + serial_port_in(port, UART_RX); serial8250_rpm_put(up); del_timer_sync(&up->timer); diff --git a/drivers/tty/serial/8250/8250_dw.c b/drivers/tty/serial/8250/8250_dw.c index e60116235836..6ae5b8560e4d 100644 --- a/drivers/tty/serial/8250/8250_dw.c +++ b/drivers/tty/serial/8250/8250_dw.c @@ -59,6 +59,8 @@ struct dw8250_data { u8 usr_reg; int last_mcr; int line; + int msr_mask_on; + int msr_mask_off; struct clk *clk; struct clk *pclk; struct reset_control *rst; @@ -81,6 +83,12 @@ static inline int dw8250_modify_msr(struct uart_port *p, int offset, int value) value &= ~UART_MSR_DCTS; } + /* Override any modem control signals if needed */ + if (offset == UART_MSR) { + value |= d->msr_mask_on; + value &= ~d->msr_mask_off; + } + return value; } @@ -111,7 +119,10 @@ static void dw8250_serial_out(struct uart_port *p, int offset, int value) dw8250_force_idle(p); writeb(value, p->membase + (UART_LCR << p->regshift)); } - dev_err(p->dev, "Couldn't set LCR to %d\n", value); + /* + * FIXME: this deadlocks if port->lock is already held + * dev_err(p->dev, "Couldn't set LCR to %d\n", value); + */ } } @@ -155,7 +166,10 @@ static void dw8250_serial_outq(struct uart_port *p, int offset, int value) __raw_writeq(value & 0xff, p->membase + (UART_LCR << p->regshift)); } - dev_err(p->dev, "Couldn't set LCR to %d\n", value); + /* + * FIXME: this deadlocks if port->lock is already held + * dev_err(p->dev, "Couldn't set LCR to %d\n", value); + */ } } #endif /* CONFIG_64BIT */ @@ -179,7 +193,10 @@ static void dw8250_serial_out32(struct uart_port *p, int offset, int value) dw8250_force_idle(p); writel(value, p->membase + (UART_LCR << p->regshift)); } - dev_err(p->dev, "Couldn't set LCR to %d\n", value); + /* + * FIXME: this deadlocks if port->lock is already held + * dev_err(p->dev, "Couldn't set LCR to %d\n", value); + */ } } @@ -334,6 +351,30 @@ static int dw8250_probe_of(struct uart_port *p, if (id >= 0) p->line = id; + if (of_property_read_bool(np, "dcd-override")) { + /* Always report DCD as active */ + data->msr_mask_on |= UART_MSR_DCD; + data->msr_mask_off |= UART_MSR_DDCD; + } + + if (of_property_read_bool(np, "dsr-override")) { + /* Always report DSR as active */ + data->msr_mask_on |= UART_MSR_DSR; + data->msr_mask_off |= UART_MSR_DDSR; + } + + if (of_property_read_bool(np, "cts-override")) { + /* Always report DSR as active */ + data->msr_mask_on |= UART_MSR_DSR; + data->msr_mask_off |= UART_MSR_DDSR; + } + + if (of_property_read_bool(np, "ri-override")) { + /* Always report Ring indicator as inactive */ + data->msr_mask_off |= UART_MSR_RI; + data->msr_mask_off |= UART_MSR_TERI; + } + /* clock got configured through clk api, all done */ if (p->uartclk) return 0; diff --git a/drivers/tty/serial/8250/8250_pci.c b/drivers/tty/serial/8250/8250_pci.c index daf2c82984e9..892eb32cdef4 100644 --- a/drivers/tty/serial/8250/8250_pci.c +++ b/drivers/tty/serial/8250/8250_pci.c @@ -69,7 +69,7 @@ static void moan_device(const char *str, struct pci_dev *dev) "Please send the output of lspci -vv, this\n" "message (0x%04x,0x%04x,0x%04x,0x%04x), the\n" "manufacturer and name of serial board or\n" - "modem board to rmk+serial@arm.linux.org.uk.\n", + "modem board to <linux-serial@vger.kernel.org>.\n", pci_name(dev), str, dev->vendor, dev->device, dev->subsystem_vendor, dev->subsystem_device); } @@ -1989,13 +1989,6 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { }, { .vendor = PCI_VENDOR_ID_INTEL, - .device = PCI_DEVICE_ID_INTEL_QRK_UART, - .subvendor = PCI_ANY_ID, - .subdevice = PCI_ANY_ID, - .setup = pci_default_setup, - }, - { - .vendor = PCI_VENDOR_ID_INTEL, .device = PCI_DEVICE_ID_INTEL_BSW_UART1, .subvendor = PCI_ANY_ID, .subdevice = PCI_ANY_ID, @@ -2201,13 +2194,6 @@ static struct pci_serial_quirk pci_serial_quirks[] __refdata = { */ { .vendor = PCI_VENDOR_ID_PLX, - .device = PCI_DEVICE_ID_PLX_9030, - .subvendor = PCI_SUBVENDOR_ID_PERLE, - .subdevice = PCI_ANY_ID, - .setup = pci_default_setup, - }, - { - .vendor = PCI_VENDOR_ID_PLX, .device = PCI_DEVICE_ID_PLX_9050, .subvendor = PCI_SUBVENDOR_ID_EXSYS, .subdevice = PCI_SUBDEVICE_ID_EXSYS_4055, @@ -5415,10 +5401,6 @@ static struct pci_device_id serial_pci_tbl[] = { PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_b0_bt_2_115200 }, - { PCI_VENDOR_ID_WCH, PCI_DEVICE_ID_WCH_CH352_2S, - PCI_ANY_ID, PCI_ANY_ID, - 0, 0, pbn_b0_bt_2_115200 }, - { PCIE_VENDOR_ID_WCH, PCIE_DEVICE_ID_WCH_CH384_4S, PCI_ANY_ID, PCI_ANY_ID, 0, 0, pbn_wch384_4 }, diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c index 846552bff67d..4e959c43f680 100644 --- a/drivers/tty/serial/atmel_serial.c +++ b/drivers/tty/serial/atmel_serial.c @@ -47,6 +47,7 @@ #include <linux/gpio/consumer.h> #include <linux/err.h> #include <linux/irq.h> +#include <linux/suspend.h> #include <asm/io.h> #include <asm/ioctls.h> @@ -173,6 +174,12 @@ struct atmel_uart_port { bool ms_irq_enabled; bool is_usart; /* usart or uart */ struct timer_list uart_timer; /* uart timer */ + + bool suspended; + unsigned int pending; + unsigned int pending_status; + spinlock_t lock_suspended; + int (*prepare_rx)(struct uart_port *port); int (*prepare_tx)(struct uart_port *port); void (*schedule_rx)(struct uart_port *port); @@ -1179,12 +1186,15 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id) { struct uart_port *port = dev_id; struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); - unsigned int status, pending, pass_counter = 0; + unsigned int status, pending, mask, pass_counter = 0; bool gpio_handled = false; + spin_lock(&atmel_port->lock_suspended); + do { status = atmel_get_lines_status(port); - pending = status & UART_GET_IMR(port); + mask = UART_GET_IMR(port); + pending = status & mask; if (!gpio_handled) { /* * Dealing with GPIO interrupt @@ -1206,11 +1216,21 @@ static irqreturn_t atmel_interrupt(int irq, void *dev_id) if (!pending) break; + if (atmel_port->suspended) { + atmel_port->pending |= pending; + atmel_port->pending_status = status; + UART_PUT_IDR(port, mask); + pm_system_wakeup(); + break; + } + atmel_handle_receive(port, pending); atmel_handle_status(port, pending, status); atmel_handle_transmit(port, pending); } while (pass_counter++ < ATMEL_ISR_PASS_LIMIT); + spin_unlock(&atmel_port->lock_suspended); + return pass_counter ? IRQ_HANDLED : IRQ_NONE; } @@ -1742,7 +1762,8 @@ static int atmel_startup(struct uart_port *port) /* * Allocate the IRQ */ - retval = request_irq(port->irq, atmel_interrupt, IRQF_SHARED, + retval = request_irq(port->irq, atmel_interrupt, + IRQF_SHARED | IRQF_COND_SUSPEND, tty ? tty->name : "atmel_serial", port); if (retval) { dev_err(port->dev, "atmel_startup - Can't get irq\n"); @@ -2513,8 +2534,14 @@ static int atmel_serial_suspend(struct platform_device *pdev, /* we can not wake up if we're running on slow clock */ atmel_port->may_wakeup = device_may_wakeup(&pdev->dev); - if (atmel_serial_clk_will_stop()) + if (atmel_serial_clk_will_stop()) { + unsigned long flags; + + spin_lock_irqsave(&atmel_port->lock_suspended, flags); + atmel_port->suspended = true; + spin_unlock_irqrestore(&atmel_port->lock_suspended, flags); device_set_wakeup_enable(&pdev->dev, 0); + } uart_suspend_port(&atmel_uart, port); @@ -2525,6 +2552,18 @@ static int atmel_serial_resume(struct platform_device *pdev) { struct uart_port *port = platform_get_drvdata(pdev); struct atmel_uart_port *atmel_port = to_atmel_uart_port(port); + unsigned long flags; + + spin_lock_irqsave(&atmel_port->lock_suspended, flags); + if (atmel_port->pending) { + atmel_handle_receive(port, atmel_port->pending); + atmel_handle_status(port, atmel_port->pending, + atmel_port->pending_status); + atmel_handle_transmit(port, atmel_port->pending); + atmel_port->pending = 0; + } + atmel_port->suspended = false; + spin_unlock_irqrestore(&atmel_port->lock_suspended, flags); uart_resume_port(&atmel_uart, port); device_set_wakeup_enable(&pdev->dev, atmel_port->may_wakeup); @@ -2593,6 +2632,8 @@ static int atmel_serial_probe(struct platform_device *pdev) port->backup_imr = 0; port->uart.line = ret; + spin_lock_init(&port->lock_suspended); + ret = atmel_init_gpios(port, &pdev->dev); if (ret < 0) dev_err(&pdev->dev, "%s", diff --git a/drivers/tty/serial/of_serial.c b/drivers/tty/serial/of_serial.c index 7ff61e24a195..33fb94f78967 100644 --- a/drivers/tty/serial/of_serial.c +++ b/drivers/tty/serial/of_serial.c @@ -133,10 +133,6 @@ static int of_platform_serial_setup(struct platform_device *ofdev, if (of_find_property(np, "no-loopback-test", NULL)) port->flags |= UPF_SKIP_TEST; - ret = of_alias_get_id(np, "serial"); - if (ret >= 0) - port->line = ret; - port->dev = &ofdev->dev; switch (type) { diff --git a/drivers/tty/serial/sprd_serial.c b/drivers/tty/serial/sprd_serial.c index 594b63331ef4..bca975f5093b 100644 --- a/drivers/tty/serial/sprd_serial.c +++ b/drivers/tty/serial/sprd_serial.c @@ -293,8 +293,10 @@ static irqreturn_t sprd_handle_irq(int irq, void *dev_id) ims = serial_in(port, SPRD_IMSR); - if (!ims) + if (!ims) { + spin_unlock(&port->lock); return IRQ_NONE; + } serial_out(port, SPRD_ICLR, ~0); |