diff options
Diffstat (limited to 'arch/cris')
| -rw-r--r-- | arch/cris/Kconfig | 4 | ||||
| -rw-r--r-- | arch/cris/arch-v10/Kconfig | 12 | ||||
| -rw-r--r-- | arch/cris/arch-v32/lib/nand_init.S | 178 |
3 files changed, 8 insertions, 186 deletions
diff --git a/arch/cris/Kconfig b/arch/cris/Kconfig index 17addacb169e..408b055c585f 100644 --- a/arch/cris/Kconfig +++ b/arch/cris/Kconfig @@ -282,8 +282,8 @@ config ETRAX_RTC Enables drivers for the Real-Time Clock battery-backed chips on some products. The kernel reads the time when booting, and the date can be set using ioctl(fd, RTC_SET_TIME, &rt) with rt a - rtc_time struct (see <file:include/asm-cris/rtc.h>) on the /dev/rtc - device. You can check the time with cat /proc/rtc, but + rtc_time struct (see <file:arch/cris/include/asm/rtc.h>) on the + /dev/rtc device. You can check the time with cat /proc/rtc, but normal time reading should be done using libc function time and friends. diff --git a/arch/cris/arch-v10/Kconfig b/arch/cris/arch-v10/Kconfig index adc164e99339..df9a38b4f18f 100644 --- a/arch/cris/arch-v10/Kconfig +++ b/arch/cris/arch-v10/Kconfig @@ -24,8 +24,8 @@ config ETRAX_PA_LEDS help The ETRAX network driver is responsible for flashing LED's when packets arrive and are sent. It uses macros defined in - <file:include/asm-cris/io.h>, and those macros are defined after what - YOU choose in this option. The actual bits used are configured + <file:arch/cris/include/asm/io.h>, and those macros are defined after + what YOU choose in this option. The actual bits used are configured separately. Select this if the LEDs are on port PA. Some products put the leds on PB or a memory-mapped latch (CSP0) instead. @@ -34,8 +34,8 @@ config ETRAX_PB_LEDS help The ETRAX network driver is responsible for flashing LED's when packets arrive and are sent. It uses macros defined in - <file:include/asm-cris/io.h>, and those macros are defined after what - YOU choose in this option. The actual bits used are configured + <file:arch/cris/include/asm/io.h>, and those macros are defined after + what YOU choose in this option. The actual bits used are configured separately. Select this if the LEDs are on port PB. Some products put the leds on PA or a memory-mapped latch (CSP0) instead. @@ -44,8 +44,8 @@ config ETRAX_CSP0_LEDS help The ETRAX network driver is responsible for flashing LED's when packets arrive and are sent. It uses macros defined in - <file:include/asm-cris/io.h>, and those macros are defined after what - YOU choose in this option. The actual bits used are configured + <file:arch/cris/include/asm/io.h>, and those macros are defined after + what YOU choose in this option. The actual bits used are configured separately. Select this if the LEDs are on a memory-mapped latch using chip select CSP0, this is mapped at 0x90000000. Some products put the leds on PA or PB instead. diff --git a/arch/cris/arch-v32/lib/nand_init.S b/arch/cris/arch-v32/lib/nand_init.S deleted file mode 100644 index d671fed451c9..000000000000 --- a/arch/cris/arch-v32/lib/nand_init.S +++ /dev/null @@ -1,178 +0,0 @@ -##============================================================================= -## -## nand_init.S -## -## The bootrom copies data from the NAND flash to the internal RAM but -## due to a bug/feature we can only trust the 256 first bytes. So this -## code copies more data from NAND flash to internal RAM. Obvioulsy this -## code must fit in the first 256 bytes so alter with care. -## -## Some notes about the bug/feature for future reference: -## The bootrom copies the first 127 KB from NAND flash to internal -## memory. The problem is that it does a bytewise copy. NAND flashes -## does autoincrement on the address so for a 16-bite device each -## read/write increases the address by two. So the copy loop in the -## bootrom will discard every second byte. This is solved by inserting -## zeroes in every second byte in the first erase block. -## -## The bootrom also incorrectly assumes that it can read the flash -## linear with only one read command but the flash will actually -## switch between normal area and spare area if you do that so we -## can't trust more than the first 256 bytes. -## -##============================================================================= - -#include <arch/hwregs/asm/reg_map_asm.h> -#include <arch/hwregs/asm/gio_defs_asm.h> -#include <arch/hwregs/asm/pinmux_defs_asm.h> -#include <arch/hwregs/asm/bif_core_defs_asm.h> -#include <arch/hwregs/asm/config_defs_asm.h> - -;; There are 8-bit NAND flashes and 16-bit NAND flashes. -;; We need to treat them slightly different. -#if CONFIG_ETRAX_FLASH_BUSWIDTH==2 -#define PAGE_SIZE 256 -#else -#error 2 -#define PAGE_SIZE 512 -#endif -#define ERASE_BLOCK 16384 - -;; GPIO pins connected to NAND flash -#define CE 4 -#define CLE 5 -#define ALE 6 -#define BY 7 - -;; Address space for NAND flash -#define NAND_RD_ADDR 0x90000000 -#define NAND_WR_ADDR 0x94000000 - -#define READ_CMD 0x00 - -;; Readability macros -#define CSP_MASK \ - REG_MASK(bif_core, rw_grp3_cfg, gated_csp0) | \ - REG_MASK(bif_core, rw_grp3_cfg, gated_csp1) -#define CSP_VAL \ - REG_STATE(bif_core, rw_grp3_cfg, gated_csp0, rd) | \ - REG_STATE(bif_core, rw_grp3_cfg, gated_csp1, wr) - -;;---------------------------------------------------------------------------- -;; Macros to set/clear GPIO bits - -.macro SET x - or.b (1<<\x),$r9 - move.d $r9, [$r2] -.endm - -.macro CLR x - and.b ~(1<<\x),$r9 - move.d $r9, [$r2] -.endm - -;;---------------------------------------------------------------------------- - -nand_boot: - ;; Check if nand boot was selected - move.d REG_ADDR(config, regi_config, r_bootsel), $r0 - move.d [$r0], $r0 - and.d REG_MASK(config, r_bootsel, boot_mode), $r0 - cmp.d REG_STATE(config, r_bootsel, boot_mode, nand), $r0 - bne normal_boot ; No NAND boot - nop - -copy_nand_to_ram: - ;; copy_nand_to_ram - ;; Arguments - ;; r10 - destination - ;; r11 - source offset - ;; r12 - size - ;; r13 - Address to jump to after completion - ;; Note : r10-r12 are clobbered on return - ;; Registers used: - ;; r0 - NAND_RD_ADDR - ;; r1 - NAND_WR_ADDR - ;; r2 - reg_gio_rw_pa_dout - ;; r3 - reg_gio_r_pa_din - ;; r4 - tmp - ;; r5 - byte counter within a page - ;; r6 - reg_pinmux_rw_pa - ;; r7 - reg_gio_rw_pa_oe - ;; r8 - reg_bif_core_rw_grp3_cfg - ;; r9 - reg_gio_rw_pa_dout shadow - move.d 0x90000000, $r0 - move.d 0x94000000, $r1 - move.d REG_ADDR(gio, regi_gio, rw_pa_dout), $r2 - move.d REG_ADDR(gio, regi_gio, r_pa_din), $r3 - move.d REG_ADDR(pinmux, regi_pinmux, rw_pa), $r6 - move.d REG_ADDR(gio, regi_gio, rw_pa_oe), $r7 - move.d REG_ADDR(bif_core, regi_bif_core, rw_grp3_cfg), $r8 - -#if CONFIG_ETRAX_FLASH_BUSWIDTH==2 - lsrq 1, $r11 -#endif - ;; Set up GPIO - move.d [$r2], $r9 - move.d [$r7], $r4 - or.b (1<<ALE) | (1 << CLE) | (1<<CE), $r4 - move.d $r4, [$r7] - - ;; Set up bif - move.d [$r8], $r4 - and.d CSP_MASK, $r4 - or.d CSP_VAL, $r4 - move.d $r4, [$r8] - -1: ;; Copy one page - CLR CE - SET CLE - moveq READ_CMD, $r4 - move.b $r4, [$r1] - moveq 20, $r4 -2: bne 2b - subq 1, $r4 - CLR CLE - SET ALE - clear.w [$r1] ; Column address = 0 - move.d $r11, $r4 - lsrq 8, $r4 - move.b $r4, [$r1] ; Row address - lsrq 8, $r4 - move.b $r4, [$r1] ; Row address - moveq 20, $r4 -2: bne 2b - subq 1, $r4 - CLR ALE -2: move.d [$r3], $r4 - and.d 1 << BY, $r4 - beq 2b - movu.w PAGE_SIZE, $r5 -2: ; Copy one byte/word -#if CONFIG_ETRAX_FLASH_BUSWIDTH==2 - move.w [$r0], $r4 -#else - move.b [$r0], $r4 -#endif - subq 1, $r5 - bne 2b -#if CONFIG_ETRAX_FLASH_BUSWIDTH==2 - move.w $r4, [$r10+] - subu.w PAGE_SIZE*2, $r12 -#else - move.b $r4, [$r10+] - subu.w PAGE_SIZE, $r12 -#endif - bpl 1b - addu.w PAGE_SIZE, $r11 - - ;; End of copy - jump $r13 - nop - - ;; This will warn if the code above is too large. If you consider - ;; to remove this you don't understand the bug/feature. - .org 256 - .org ERASE_BLOCK - -normal_boot: |