diff options
Diffstat (limited to 'arch/cris/arch-v10/boot/rescue/kimagerescue.S')
| -rw-r--r-- | arch/cris/arch-v10/boot/rescue/kimagerescue.S | 58 |
1 files changed, 29 insertions, 29 deletions
diff --git a/arch/cris/arch-v10/boot/rescue/kimagerescue.S b/arch/cris/arch-v10/boot/rescue/kimagerescue.S index cbccd6316d39..55eeff8bb08e 100644 --- a/arch/cris/arch-v10/boot/rescue/kimagerescue.S +++ b/arch/cris/arch-v10/boot/rescue/kimagerescue.S @@ -1,5 +1,4 @@ -/* $Id: kimagerescue.S,v 1.1 2001/12/17 13:59:27 bjornw Exp $ - * +/* * Rescue code to be prepended on a kimage and copied to the * rescue serial port. * This is called from the rescue code, it will copy received data to @@ -7,13 +6,13 @@ */ #define ASSEMBLER_MACROS_ONLY -#include <asm/sv_addr_ag.h> +#include <asm/arch/sv_addr_ag.h> #define CODE_START 0x40004000 #define CODE_LENGTH 784 #define TIMEOUT_VALUE 1000 - - + + #ifdef CONFIG_ETRAX_RESCUE_SER0 #define SERXOFF R_SERIAL0_XOFF #define SERBAUD R_SERIAL0_BAUD @@ -34,7 +33,7 @@ #define SERRECC R_SERIAL2_REC_CTRL #define SERRDAT R_SERIAL2_REC_DATA #define SERSTAT R_SERIAL2_STATUS -#endif +#endif #ifdef CONFIG_ETRAX_RESCUE_SER3 #define SERXOFF R_SERIAL3_XOFF #define SERBAUD R_SERIAL3_BAUD @@ -48,54 +47,55 @@ ;; 0x80000000 if loaded in flash (as it should be) ;; since etrax actually starts at address 2 when booting from flash, we ;; put a nop (2 bytes) here first so we dont accidentally skip the di - - nop + + nop di -#ifndef CONFIG_SVINTO_SIM +#ifndef CONFIG_SVINTO_SIM ;; setup port PA and PB default initial directions and data ;; (so we can flash LEDs, and so that DTR and others are set) - + move.b CONFIG_ETRAX_DEF_R_PORT_PA_DIR, $r0 move.b $r0, [R_PORT_PA_DIR] move.b CONFIG_ETRAX_DEF_R_PORT_PA_DATA, $r0 move.b $r0, [R_PORT_PA_DATA] - + move.b CONFIG_ETRAX_DEF_R_PORT_PB_DIR, $r0 move.b $r0, [R_PORT_PB_DIR] move.b CONFIG_ETRAX_DEF_R_PORT_PB_DATA, $r0 move.b $r0, [R_PORT_PB_DATA] - + ;; We need to setup the bus registers before we start using the DRAM #include "../../lib/dram_init.S" - + #endif ;; Setup the stack to a suitably high address. ;; We assume 8 MB is the minimum DRAM in an eLinux ;; product and put the sp at the top for now. move.d 0x40800000, $sp - + ;; setup the serial port at 115200 baud - + moveq 0, $r0 - move.d $r0, [SERXOFF] + move.d $r0, [SERXOFF] move.b 0x99, $r0 - move.b $r0, [SERBAUD] ; 115.2kbaud for both transmit and receive + move.b $r0, [SERBAUD] ; 115.2kbaud for both transmit + ; and receive move.b 0x40, $r0 ; rec enable - move.b $r0, [SERRECC] + move.b $r0, [SERRECC] - moveq 0, $r1 ; "timer" to clock out a LED red flash - move.d CODE_START, $r3 ; destination counter + moveq 0, $r1 ; "timer" to clock out a LED red flash + move.d CODE_START, $r3 ; destination counter move.d CODE_LENGTH, $r4 ; length move.d TIMEOUT_VALUE, $r5 ; "timeout" until jump wait_ser: addq 1, $r1 - subq 1, $r5 ; decrease timeout - beq jump_start ; timed out + subq 1, $r5 ; decrease timeout + beq jump_start ; timed out nop #ifndef CONFIG_ETRAX_NO_LEDS #ifdef CONFIG_ETRAX_PA_LEDS @@ -111,21 +111,21 @@ wait_ser: or.d $r0, $r2 ; set bit ba 2f nop -1: not $r0 ; clear bit +1: not $r0 ; clear bit and.d $r0, $r2 -2: +2: #ifdef CONFIG_ETRAX_PA_LEDS move.b $r2, [R_PORT_PA_DATA] -#endif +#endif #ifdef CONFIG_ETRAX_PB_LEDS move.b $r2, [R_PORT_PB_DATA] #endif #endif - + ;; check if we got something on the serial port - + move.b [SERSTAT], $r0 - btstq 0, $r0 ; data_avail + btstq 0, $r0 ; data_avail bpl wait_ser nop @@ -134,7 +134,7 @@ wait_ser: move.b [SERRDAT], $r0 move.b $r0, [$r3+] move.d TIMEOUT_VALUE, $r5 ; reset "timeout" - subq 1, $r4 ; decrease length + subq 1, $r4 ; decrease length bne wait_ser nop jump_start: |