1 files changed, 0 insertions, 343 deletions
diff --git a/arch/arm/mach-lh7a40x/ssp-cpld.c b/arch/arm/mach-lh7a40x/ssp-cpld.c
deleted file mode 100644
index 2901d49d1484..000000000000
--- a/arch/arm/mach-lh7a40x/ssp-cpld.c
+++ /dev/null
@@ -1,343 +0,0 @@
-/* arch/arm/mach-lh7a40x/ssp-cpld.c
- *
- *  Copyright (C) 2004,2005 Marc Singer
- *
- *  This program is free software; you can redistribute it and/or
- *  modify it under the terms of the GNU General Public License
- *  version 2 as published by the Free Software Foundation.
- *
- * SSP/SPI driver for the CardEngine CPLD.
- *
- */
-
-/* NOTES
-   -----
-
-   o *** This driver is cribbed from the 7952x implementation.
-	 Some comments may not apply.
-
-   o This driver contains sufficient logic to control either the
-     serial EEPROMs or the audio codec.  It is included in the kernel
-     to support the codec.  The EEPROMs are really the responsibility
-     of the boot loader and should probably be left alone.
-
-   o The code must be augmented to cope with multiple, simultaneous
-     clients.
-     o The audio codec writes to the codec chip whenever playback
-       starts.
-     o The touchscreen driver writes to the ads chip every time it
-       samples.
-     o The audio codec must write 16 bits, but the touch chip writes
-       are 8 bits long.
-     o We need to be able to keep these configurations separate while
-       simultaneously active.
-
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-//#include <linux/sched.h>
-#include <linux/errno.h>
-#include <linux/interrupt.h>
-//#include <linux/ioport.h>
-#include <linux/init.h>
-#include <linux/delay.h>
-#include <linux/spinlock.h>
-#include <linux/io.h>
-
-#include <asm/irq.h>
-#include <mach/hardware.h>
-
-#include <mach/ssp.h>
-
-//#define TALK
-
-#if defined (TALK)
-#define PRINTK(f...)		printk (f)
-#else
-#define PRINTK(f...)		do {} while (0)
-#endif
-
-#if defined (CONFIG_ARCH_LH7A400)
-# define CPLD_SPID		__REGP16(CPLD06_VIRT) /* SPI data */
-# define CPLD_SPIC		__REGP16(CPLD08_VIRT) /* SPI control */
-# define CPLD_SPIC_CS_CODEC	(1<<0)
-# define CPLD_SPIC_CS_TOUCH	(1<<1)
-# define CPLD_SPIC_WRITE	(0<<2)
-# define CPLD_SPIC_READ		(1<<2)
-# define CPLD_SPIC_DONE		(1<<3) /* r/o */
-# define CPLD_SPIC_LOAD		(1<<4)
-# define CPLD_SPIC_START	(1<<4)
-# define CPLD_SPIC_LOADED	(1<<5) /* r/o */
-#endif
-
-#define CPLD_SPI		__REGP16(CPLD0A_VIRT) /* SPI operation */
-#define CPLD_SPI_CS_EEPROM	(1<<3)
-#define CPLD_SPI_SCLK		(1<<2)
-#define CPLD_SPI_TX_SHIFT	(1)
-#define CPLD_SPI_TX		(1<<CPLD_SPI_TX_SHIFT)
-#define CPLD_SPI_RX_SHIFT	(0)
-#define CPLD_SPI_RX		(1<<CPLD_SPI_RX_SHIFT)
-
-/* *** FIXME: these timing values are substantially larger than the
-   *** chip requires. We may implement an nsleep () function. */
-#define T_SKH	1		/* Clock time high (us) */
-#define T_SKL	1		/* Clock time low (us) */
-#define T_CS	1		/* Minimum chip select low time (us)  */
-#define T_CSS	1		/* Minimum chip select setup time (us)  */
-#define T_DIS	1		/* Data setup time (us) */
-
-	 /* EEPROM SPI bits */
-#define P_START		(1<<9)
-#define P_WRITE		(1<<7)
-#define P_READ		(2<<7)
-#define P_ERASE		(3<<7)
-#define P_EWDS		(0<<7)
-#define P_WRAL		(0<<7)
-#define P_ERAL		(0<<7)
-#define P_EWEN		(0<<7)
-#define P_A_EWDS	(0<<5)
-#define P_A_WRAL	(1<<5)
-#define P_A_ERAL	(2<<5)
-#define P_A_EWEN	(3<<5)
-
-struct ssp_configuration {
-	int device;
-	int mode;
-	int speed;
-	int frame_size_write;
-	int frame_size_read;
-};
-
-static struct ssp_configuration ssp_configuration;
-static spinlock_t ssp_lock;
-
-static void enable_cs (void)
-{
-	switch (ssp_configuration.device) {
-	case DEVICE_EEPROM:
-		CPLD_SPI |= CPLD_SPI_CS_EEPROM;
-		break;
-	}
-	udelay (T_CSS);
-}
-
-static void disable_cs (void)
-{
-	switch (ssp_configuration.device) {
-	case DEVICE_EEPROM:
-		CPLD_SPI &= ~CPLD_SPI_CS_EEPROM;
-		break;
-	}
-	udelay (T_CS);
-}
-
-static void pulse_clock (void)
-{
-	CPLD_SPI |=  CPLD_SPI_SCLK;
-	udelay (T_SKH);
-	CPLD_SPI &= ~CPLD_SPI_SCLK;
-	udelay (T_SKL);
-}
-
-
-/* execute_spi_command
-
-   sends an spi command to a device.  It first sends cwrite bits from
-   v.  If cread is greater than zero it will read cread bits
-   (discarding the leading 0 bit) and return them.  If cread is less
-   than zero it will check for completetion status and return 0 on
-   success or -1 on timeout.  If cread is zero it does nothing other
-   than sending the command.
-
-   On the LPD7A400, we can only read or write multiples of 8 bits on
-   the codec and the touch screen device.  Here, we round up.
-
-*/
-
-static int execute_spi_command (int v, int cwrite, int cread)
-{
-	unsigned long l = 0;
-
-#if defined (CONFIG_MACH_LPD7A400)
-	/* The codec and touch devices cannot be bit-banged.  Instead,
-	 * the CPLD provides an eight-bit shift register and a crude
-	 * interface.  */
-	if (   ssp_configuration.device == DEVICE_CODEC
-	    || ssp_configuration.device == DEVICE_TOUCH) {
-		int select = 0;
-
-		PRINTK ("spi(%d %d.%d) 0x%04x",
-			ssp_configuration.device, cwrite, cread,
-			v);
-#if defined (TALK)
-		if (ssp_configuration.device == DEVICE_CODEC)
-			PRINTK (" 0x%03x -> %2d", v & 0x1ff, (v >> 9) & 0x7f);
-#endif
-		PRINTK ("\n");
-
-		if (ssp_configuration.device == DEVICE_CODEC)
-			select = CPLD_SPIC_CS_CODEC;
-		if (ssp_configuration.device == DEVICE_TOUCH)
-			select = CPLD_SPIC_CS_TOUCH;
-		if (cwrite) {
-			for (cwrite = (cwrite + 7)/8; cwrite-- > 0; ) {
-				CPLD_SPID = (v >> (8*cwrite)) & 0xff;
-				CPLD_SPIC = select | CPLD_SPIC_LOAD;
-				while (!(CPLD_SPIC & CPLD_SPIC_LOADED))
-					;
-				CPLD_SPIC = select;
-				while (!(CPLD_SPIC & CPLD_SPIC_DONE))
-					;
-			}
-			v = 0;
-		}
-		if (cread) {
-			mdelay (2);	/* *** FIXME: required by ads7843? */
-			v = 0;
-			for (cread = (cread + 7)/8; cread-- > 0;) {
-				CPLD_SPID = 0;
-				CPLD_SPIC = select | CPLD_SPIC_READ
-					| CPLD_SPIC_START;
-				while (!(CPLD_SPIC & CPLD_SPIC_LOADED))
-					;
-				CPLD_SPIC = select | CPLD_SPIC_READ;
-				while (!(CPLD_SPIC & CPLD_SPIC_DONE))
-					;
-				v = (v << 8) | CPLD_SPID;
-			}
-		}
-		return v;
-	}
-#endif
-
-	PRINTK ("spi(%d) 0x%04x -> 0x%x\r\n", ssp_configuration.device,
-		v & 0x1ff, (v >> 9) & 0x7f);
-
-	enable_cs ();
-
-	v <<= CPLD_SPI_TX_SHIFT; /* Correction for position of SPI_TX bit */
-	while (cwrite--) {
-		CPLD_SPI
-			= (CPLD_SPI & ~CPLD_SPI_TX)
-			| ((v >> cwrite) & CPLD_SPI_TX);
-		udelay (T_DIS);
-		pulse_clock ();
-	}
-
-	if (cread < 0) {
-		int delay = 10;
-		disable_cs ();
-		udelay (1);
-		enable_cs ();
-
-		l = -1;
-		do {
-			if (CPLD_SPI & CPLD_SPI_RX) {
-				l = 0;
-				break;
-			}
-		} while (udelay (1), --delay);
-	}
-	else
-	/* We pulse the clock before the data to skip the leading zero. */
-		while (cread-- > 0) {
-			pulse_clock ();
-			l = (l<<1)
-				| (((CPLD_SPI & CPLD_SPI_RX)
-				    >> CPLD_SPI_RX_SHIFT) & 0x1);
-		}
-
-	disable_cs ();
-	return l;
-}
-
-static int ssp_init (void)
-{
-	spin_lock_init (&ssp_lock);
-	memset (&ssp_configuration, 0, sizeof (ssp_configuration));
-	return 0;
-}
-
-
-/* ssp_chip_select
-
-   drops the chip select line for the CPLD shift-register controlled
-   devices.  It doesn't enable chip
-
-*/
-
-static void ssp_chip_select (int enable)
-{
-#if defined (CONFIG_MACH_LPD7A400)
-	int select;
-
-	if (ssp_configuration.device == DEVICE_CODEC)
-		select = CPLD_SPIC_CS_CODEC;
-	else if (ssp_configuration.device == DEVICE_TOUCH)
-		select = CPLD_SPIC_CS_TOUCH;
-	else
-		return;
-
-	if (enable)
-		CPLD_SPIC = select;
-	else
-		CPLD_SPIC = 0;
-#endif
-}
-
-static void ssp_acquire (void)
-{
-	spin_lock (&ssp_lock);
-}
-
-static void ssp_release (void)
-{
-	ssp_chip_select (0);	/* just in case */
-	spin_unlock (&ssp_lock);
-}
-
-static int ssp_configure (int device, int mode, int speed,
-			   int frame_size_write, int frame_size_read)
-{
-	ssp_configuration.device		= device;
-	ssp_configuration.mode			= mode;
-	ssp_configuration.speed			= speed;
-	ssp_configuration.frame_size_write	= frame_size_write;
-	ssp_configuration.frame_size_read	= frame_size_read;
-
-	return 0;
-}
-
-static int ssp_read (void)
-{
-	return execute_spi_command (0, 0, ssp_configuration.frame_size_read);
-}
-
-static int ssp_write (u16 data)
-{
-	execute_spi_command (data, ssp_configuration.frame_size_write, 0);
-	return 0;
-}
-
-static int ssp_write_read (u16 data)
-{
-	return execute_spi_command (data, ssp_configuration.frame_size_write,
-				    ssp_configuration.frame_size_read);
-}
-
-struct ssp_driver lh7a40x_cpld_ssp_driver = {
-	.init		= ssp_init,
-	.acquire	= ssp_acquire,
-	.release	= ssp_release,
-	.configure	= ssp_configure,
-	.chip_select	= ssp_chip_select,
-	.read		= ssp_read,
-	.write		= ssp_write,
-	.write_read	= ssp_write_read,
-};
-
-
-MODULE_AUTHOR("Marc Singer");
-MODULE_DESCRIPTION("LPD7A40X CPLD SPI driver");
-MODULE_LICENSE("GPL");