diff options
Diffstat (limited to 'arch/arm/boot/dts/ste-hrefv60plus.dtsi')
| -rw-r--r-- | arch/arm/boot/dts/ste-hrefv60plus.dtsi | 251 |
1 files changed, 211 insertions, 40 deletions
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi index aed511b47a9e..3b6d1181939b 100644 --- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi +++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi @@ -16,55 +16,226 @@ model = "ST-Ericsson HREF (v60+) platform with Device Tree"; compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500"; - gpio_keys { - button@1 { - gpios = <&gpio5 25 0x4>; - }; - }; - soc { // External Micro SD slot sdi0_per1@80126000 { - arm,primecell-periphid = <0x10480180>; - max-frequency = <100000000>; - bus-width = <4>; - mmc-cap-sd-highspeed; - mmc-cap-mmc-highspeed; - vmmc-supply = <&ab8500_ldo_aux3_reg>; - cd-gpios = <&gpio2 31 0x4>; // 95 - - status = "okay"; }; - // WLAN SDIO channel - sdi1_per2@80118000 { - arm,primecell-periphid = <0x10480180>; - max-frequency = <100000000>; - bus-width = <4>; - - status = "okay"; - }; - - // PoP:ed eMMC - sdi2_per3@80005000 { - arm,primecell-periphid = <0x10480180>; - max-frequency = <100000000>; - bus-width = <8>; - mmc-cap-mmc-highspeed; - - status = "okay"; + vmmci: regulator-gpio { + gpios = <&gpio0 5 0x4>; + enable-gpio = <&gpio5 9 0x4>; }; - // On-board eMMC - sdi4_per2@80114000 { - arm,primecell-periphid = <0x10480180>; - max-frequency = <100000000>; - bus-width = <8>; - mmc-cap-mmc-highspeed; - vmmc-supply = <&ab8500_ldo_aux2_reg>; + pinctrl { + /* + * Set this up using hogs, as time goes by and as seems fit, these + * can be moved over to being controlled by respective device. + */ + pinctrl-names = "default"; + pinctrl-0 = <&ipgpio_hrefv60_mode>, + <&accel_hrefv60_mode>, + <&magneto_hrefv60_mode>, + <&etm_hrefv60_mode>, + <&nahj_hrefv60_mode>, + <&nfc_hrefv60_mode>, + <&force_hrefv60_mode>, + <&dipro_hrefv60_mode>, + <&vaudio_hf_hrefv60_mode>, + <&gbf_hrefv60_mode>, + <&hdtv_hrefv60_mode>, + <&touch_hrefv60_mode>; - status = "okay"; + sdi0 { + /* SD card detect GPIO pin, extend default state */ + sdi0_default_mode: sdi0_default { + default_hrefv60_cfg1 { + ste,pins = "GPIO95_E8"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + ipgpio { + /* + * XENON Flashgun on image processor GPIO (controlled from image + * processor firmware), mux in these image processor GPIO lines 0 + * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant + * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias + * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output. + */ + ipgpio_hrefv60_mode: ipgpio_hrefv60 { + hrefv60_mux { + ste,function = "ipgpio"; + ste,pins = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1"; + }; + hrefv60_cfg1 { + ste,pins = "GPIO6_AF6", "GPIO7_AG5"; + ste,config = <&in_pu>; + }; + hrefv60_cfg2 { + ste,pins = "GPIO21_AB3"; + ste,config = <&gpio_out_lo>; + }; + hrefv60_cfg3 { + ste,pins = "GPIO64_F3"; + ste,config = <&out_lo>; + }; + }; + }; + accelerometer { + accel_hrefv60_mode: accel_hrefv60 { + /* Accelerometer interrupt lines 1 & 2 */ + hrefv60_cfg1 { + ste,pins = "GPIO82_C1", "GPIO83_D3"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + magnetometer { + magneto_hrefv60_mode: magneto_hrefv60 { + /* Magnetometer uses GPIO 31 and 32, pull these up/down respectively */ + hrefv60_cfg1 { + ste,pins = "GPIO31_V3"; + ste,config = <&gpio_in_pu>; + }; + hrefv60_cfg2 { + ste,pins = "GPIO32_V2"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + etm { + /* + * Drive D19-D23 for the ETM PTM trace interface low, + * (presumably pins are unconnected therefore grounded here, + * the "other alt C1" setting enables these pins) + */ + etm_hrefv60_mode: etm_hrefv60 { + hrefv60_cfg1 { + ste,pins = + "GPIO70_G5", + "GPIO71_G4", + "GPIO72_H4", + "GPIO73_H3", + "GPIO74_J3"; + ste,config = <&gpio_out_lo>; + }; + }; + }; + nahj { + nahj_hrefv60_mode: nahj_hrefv60 { + /* NAHJ CTRL on GPIO76 to low, CTRL_INV on GPIO216 to high */ + hrefv60_cfg1 { + ste,pins = "GPIO76_J2"; + ste,config = <&gpio_out_lo>; + }; + hrefv60_cfg2 { + ste,pins = "GPIO216_AG12"; + ste,config = <&gpio_out_hi>; + }; + }; + }; + nfc { + nfc_hrefv60_mode: nfc_hrefv60 { + /* NFC ENA and RESET to low, pulldown IRQ line */ + hrefv60_cfg1 { + ste,pins = + "GPIO77_H1", /* NFC_ENA */ + "GPIO142_C11"; /* NFC_RESET */ + ste,config = <&gpio_out_lo>; + }; + hrefv60_cfg2 { + ste,pins = "GPIO144_B13"; /* NFC_IRQ */ + ste,config = <&gpio_in_pd>; + }; + }; + }; + force { + force_hrefv60_mode: force_hrefv60 { + hrefv60_cfg1 { + ste,pins = "GPIO91_B6"; /* FORCE_SENSING_INT */ + ste,config = <&gpio_in_pu>; + }; + hrefv60_cfg2 { + ste,pins = + "GPIO92_D6", /* FORCE_SENSING_RST */ + "GPIO97_D9"; /* FORCE_SENSING_WU */ + ste,config = <&gpio_out_lo>; + }; + }; + }; + dipro { + dipro_hrefv60_mode: dipro_hrefv60 { + hrefv60_cfg1 { + ste,pins = "GPIO139_C9"; /* DIPRO_INT */ + ste,config = <&gpio_in_pu>; + }; + }; + }; + vaudio_hf { + vaudio_hf_hrefv60_mode: vaudio_hf_hrefv60 { + /* Audio Amplifier HF enable GPIO */ + hrefv60_cfg1 { + ste,pins = "GPIO149_B14"; /* VAUDIO_HF_EN, enable MAX8968 */ + ste,config = <&gpio_out_hi>; + }; + }; + }; + gbf { + gbf_hrefv60_mode: gbf_hrefv60 { + /* + * GBF (GPS, Bluetooth, FM-radio) interface, + * pull low to reset state + */ + hrefv60_cfg1 { + ste,pins = "GPIO171_D23"; /* GBF_ENA_RESET */ + ste,config = <&gpio_out_lo>; + }; + }; + }; + hdtv { + hdtv_hrefv60_mode: hdtv_hrefv60 { + /* MSP : HDTV INTERFACE GPIO line */ + hrefv60_cfg1 { + ste,pins = "GPIO192_AJ27"; + ste,config = <&gpio_in_pd>; + }; + }; + }; + touch { + touch_hrefv60_mode: touch_hrefv60 { + /* + * Touch screen uses GPIO 143 for RST1, GPIO 146 for RST2 and + * GPIO 67 for interrupts. Pull-up the IRQ line and drive both + * reset signals low. + */ + hrefv60_cfg1 { + ste,pins = "GPIO143_D12", "GPIO146_D13"; + ste,config = <&gpio_out_lo>; + }; + hrefv60_cfg2 { + ste,pins = "GPIO67_G2"; + ste,config = <&gpio_in_pu>; + }; + }; + }; + mcde { + lcd_hrefv60_mode: lcd_hrefv60 { + /* + * Display Interface 1 uses GPIO 65 for RST (reset). + * Display Interface 2 uses GPIO 66 for RST (reset). + * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset) + */ + hrefv60_cfg1 { + ste,pins ="GPIO65_F1"; + ste,config = <&gpio_out_hi>; + }; + hrefv60_cfg2 { + ste,pins ="GPIO66_G3"; + ste,config = <&gpio_out_lo>; + }; + }; + }; }; }; }; |