diff options
Diffstat (limited to 'Documentation')
6 files changed, 78 insertions, 18 deletions
diff --git a/Documentation/devicetree/bindings/thermal/qcom-spmi-temp-alarm.txt b/Documentation/devicetree/bindings/thermal/qcom-spmi-temp-alarm.txt index 290ec06fa33a..0273a92a2a84 100644 --- a/Documentation/devicetree/bindings/thermal/qcom-spmi-temp-alarm.txt +++ b/Documentation/devicetree/bindings/thermal/qcom-spmi-temp-alarm.txt @@ -6,8 +6,7 @@ interrupt signal and status register to identify high PMIC die temperature. Required properties: - compatible: Should contain "qcom,spmi-temp-alarm". -- reg: Specifies the SPMI address and length of the controller's - registers. +- reg: Specifies the SPMI address. - interrupts: PMIC temperature alarm interrupt. - #thermal-sensor-cells: Should be 0. See thermal.txt for a description. @@ -20,7 +19,7 @@ Example: pm8941_temp: thermal-alarm@2400 { compatible = "qcom,spmi-temp-alarm"; - reg = <0x2400 0x100>; + reg = <0x2400>; interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>; #thermal-sensor-cells = <0>; @@ -36,19 +35,14 @@ Example: thermal-sensors = <&pm8941_temp>; trips { - passive { - temperature = <1050000>; + stage1 { + temperature = <105000>; hysteresis = <2000>; type = "passive"; }; - alert { + stage2 { temperature = <125000>; hysteresis = <2000>; - type = "hot"; - }; - crit { - temperature = <145000>; - hysteresis = <2000>; type = "critical"; }; }; diff --git a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt index 20ca4ef9d776..04cbb90a5d3e 100644 --- a/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/qoriq-thermal.txt @@ -1,9 +1,9 @@ * Thermal Monitoring Unit (TMU) on Freescale QorIQ SoCs Required properties: -- compatible : Must include "fsl,qoriq-tmu". The version of the device is - determined by the TMU IP Block Revision Register (IPBRR0) at - offset 0x0BF8. +- compatible : Must include "fsl,qoriq-tmu" or "fsl,imx8mq-tmu". The + version of the device is determined by the TMU IP Block Revision + Register (IPBRR0) at offset 0x0BF8. Table of correspondences between IPBRR0 values and example chips: Value Device ---------- ----- diff --git a/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt index cfa154bb0fa7..ad9a435afef4 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-gen3-thermal.txt @@ -7,9 +7,11 @@ inside the LSI. Required properties: - compatible : "renesas,<soctype>-thermal", Examples with soctypes are: + - "renesas,r8a774a1-thermal" (RZ/G2M) - "renesas,r8a7795-thermal" (R-Car H3) - "renesas,r8a7796-thermal" (R-Car M3-W) - "renesas,r8a77965-thermal" (R-Car M3-N) + - "renesas,r8a77980-thermal" (R-Car V3H) - reg : Address ranges of the thermal registers. Each sensor needs one address range. Sorting must be done in increasing order according to datasheet, i.e. @@ -19,7 +21,8 @@ Required properties: Optional properties: -- interrupts : interrupts routed to the TSC (3 for H3, M3-W and M3-N) +- interrupts : interrupts routed to the TSC (3 for H3, M3-W, M3-N, + and V3H) - power-domain : Must contain a reference to the power domain. This property is mandatory if the thermal sensor instance is part of a controllable power domain. diff --git a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt index 67c563f1b4c4..73e1613d2cb0 100644 --- a/Documentation/devicetree/bindings/thermal/rcar-thermal.txt +++ b/Documentation/devicetree/bindings/thermal/rcar-thermal.txt @@ -4,15 +4,17 @@ Required properties: - compatible : "renesas,thermal-<soctype>", "renesas,rcar-gen2-thermal" (with thermal-zone) or "renesas,rcar-thermal" (without thermal-zone) as - fallback except R-Car D3. + fallback except R-Car V3M/D3. Examples with soctypes are: - "renesas,thermal-r8a73a4" (R-Mobile APE6) - "renesas,thermal-r8a7743" (RZ/G1M) + - "renesas,thermal-r8a7744" (RZ/G1N) - "renesas,thermal-r8a7779" (R-Car H1) - "renesas,thermal-r8a7790" (R-Car H2) - "renesas,thermal-r8a7791" (R-Car M2-W) - "renesas,thermal-r8a7792" (R-Car V2H) - "renesas,thermal-r8a7793" (R-Car M2-N) + - "renesas,thermal-r8a77970" (R-Car V3M) - "renesas,thermal-r8a77995" (R-Car D3) - reg : Address range of the thermal registers. The 1st reg will be recognized as common register @@ -21,7 +23,7 @@ Required properties: Option properties: - interrupts : If present should contain 3 interrupts for - R-Car D3 or 1 interrupt otherwise. + R-Car V3M/D3 or 1 interrupt otherwise. Example (non interrupt support): diff --git a/Documentation/devicetree/bindings/thermal/stm32-thermal.txt b/Documentation/devicetree/bindings/thermal/stm32-thermal.txt new file mode 100644 index 000000000000..8c0d5a4d8031 --- /dev/null +++ b/Documentation/devicetree/bindings/thermal/stm32-thermal.txt @@ -0,0 +1,61 @@ +Binding for Thermal Sensor for STMicroelectronics STM32 series of SoCs. + +On STM32 SoCs, the Digital Temperature Sensor (DTS) is in charge of managing an +analog block which delivers a frequency depending on the internal SoC's +temperature. By using a reference frequency, DTS is able to provide a sample +number which can be translated into a temperature by the user. + +DTS provides interrupt notification mechanism by threshold. This mechanism +offers two temperature trip points: passive and critical. The first is intended +for passive cooling notification while the second is used for over-temperature +reset. + +Required parameters: +------------------- + +compatible: Should be "st,stm32-thermal" +reg: This should be the physical base address and length of the + sensor's registers. +clocks: Phandle of the clock used by the thermal sensor. + See: Documentation/devicetree/bindings/clock/clock-bindings.txt +clock-names: Should be "pclk" for register access clock and reference clock. + See: Documentation/devicetree/bindings/resource-names.txt +#thermal-sensor-cells: Should be 0. See ./thermal.txt for a description. +interrupts: Standard way to define interrupt number. + +Example: + + thermal-zones { + cpu_thermal: cpu-thermal { + polling-delay-passive = <0>; + polling-delay = <0>; + + thermal-sensors = <&thermal>; + + trips { + cpu_alert1: cpu-alert1 { + temperature = <85000>; + hysteresis = <0>; + type = "passive"; + }; + + cpu-crit: cpu-crit { + temperature = <120000>; + hysteresis = <0>; + type = "critical"; + }; + }; + + cooling-maps { + }; + }; + }; + + thermal: thermal@50028000 { + compatible = "st,stm32-thermal"; + reg = <0x50028000 0x100>; + clocks = <&rcc TMPSENS>; + clock-names = "pclk"; + #thermal-sensor-cells = <0>; + interrupts = <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/thermal/thermal.txt b/Documentation/devicetree/bindings/thermal/thermal.txt index eb7ee91556a5..ca14ba959e0d 100644 --- a/Documentation/devicetree/bindings/thermal/thermal.txt +++ b/Documentation/devicetree/bindings/thermal/thermal.txt @@ -152,7 +152,7 @@ Optional property: Elem size: one cell the sensors listed in the thermal-sensors property. Elem type: signed Coefficients defaults to 1, in case this property is not specified. A simple linear polynomial is used: - Z = c0 * x0 + c1 + x1 + ... + c(n-1) * x(n-1) + cn. + Z = c0 * x0 + c1 * x1 + ... + c(n-1) * x(n-1) + cn. The coefficients are ordered and they match with sensors by means of sensor ID. Additional coefficients are |