diff options
Diffstat (limited to 'Documentation')
7 files changed, 163 insertions, 7 deletions
diff --git a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt index 623fedf12180..715047444391 100644 --- a/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt +++ b/Documentation/devicetree/bindings/arm/freescale/fsl,scu.txt @@ -108,7 +108,8 @@ This binding uses the i.MX common pinctrl binding[3]. Required properties: - compatible: Should be one of: "fsl,imx8qm-iomuxc", - "fsl,imx8qxp-iomuxc". + "fsl,imx8qxp-iomuxc", + "fsl,imx8dxl-iomuxc". Required properties for Pinctrl sub nodes: - fsl,pins: Each entry consists of 3 integers which represents @@ -116,7 +117,8 @@ Required properties for Pinctrl sub nodes: integers <pin_id mux_mode> are specified using a PIN_FUNC_ID macro, which can be found in <dt-bindings/pinctrl/pads-imx8qm.h>, - <dt-bindings/pinctrl/pads-imx8qxp.h>. + <dt-bindings/pinctrl/pads-imx8qxp.h>, + <dt-bindings/pinctrl/pads-imx8dxl.h>. The last integer CONFIG is the pad setting value like pull-up on this pin. diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt index 3cab7336a326..5682b2010e50 100644 --- a/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt +++ b/Documentation/devicetree/bindings/pinctrl/brcm,bcm2835-gpio.txt @@ -9,13 +9,16 @@ Required properties: "brcm,bcm2835-gpio" - BCM2835 compatible pinctrl "brcm,bcm7211-gpio" - BCM7211 compatible pinctrl "brcm,bcm2711-gpio" - BCM2711 compatible pinctrl + "brcm,bcm7211-gpio" - BCM7211 compatible pinctrl - reg: Should contain the physical address of the GPIO module's registers. - gpio-controller: Marks the device node as a GPIO controller. - #gpio-cells : Should be two. The first cell is the pin number and the second cell is used to specify optional parameters: - bit 0 specifies polarity (0 for normal, 1 for inverted) - interrupts : The interrupt outputs from the controller. One interrupt per - individual bank followed by the "all banks" interrupt. + individual bank followed by the "all banks" interrupt. For BCM7211, an + additional set of per-bank interrupt line and an "all banks" wake-up + interrupt may be specified. - interrupt-controller: Marks the device node as an interrupt controller. - #interrupt-cells : Should be 2. The first cell is the GPIO number. diff --git a/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt index 32a8a8fa7805..00912449237b 100644 --- a/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/mscc,ocelot-pinctrl.txt @@ -2,8 +2,8 @@ Microsemi Ocelot pin controller Device Tree Bindings ---------------------------------------------------- Required properties: - - compatible : Should be "mscc,ocelot-pinctrl" or - "mscc,jaguar2-pinctrl" + - compatible : Should be "mscc,ocelot-pinctrl", + "mscc,jaguar2-pinctrl" or "microchip,sparx5-pinctrl" - reg : Address and length of the register set for the device - gpio-controller : Indicates this device is a GPIO controller - #gpio-cells : Must be 2. diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml new file mode 100644 index 000000000000..6dc3b52f47cd --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/qcom,sm8250-pinctrl.yaml @@ -0,0 +1,147 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/qcom,sm8250-pinctrl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Technologies, Inc. SM8250 TLMM block + +maintainers: + - Bjorn Andersson <bjorn.andersson@linaro.org> + +description: | + This binding describes the Top Level Mode Multiplexer block found in the + SM8250 platform. + +properties: + compatible: + const: qcom,sm8250-pinctrl + + reg: + minItems: 3 + maxItems: 3 + + reg-names: + items: + - const: "west" + - const: "south" + - const: "north" + + interrupts: + description: Specifies the TLMM summary IRQ + maxItems: 1 + + interrupt-controller: true + + '#interrupt-cells': + description: + Specifies the PIN numbers and Flags, as defined in defined in + include/dt-bindings/interrupt-controller/irq.h + const: 2 + + gpio-controller: true + + '#gpio-cells': + description: Specifying the pin number and flags, as defined in + include/dt-bindings/gpio/gpio.h + const: 2 + + gpio-ranges: + maxItems: 1 + + wakeup-parent: + maxItems: 1 + +#PIN CONFIGURATION NODES +patternProperties: + '^.*$': + if: + type: object + then: + properties: + pins: + description: + List of gpio pins affected by the properties specified in this + subnode. + items: + oneOf: + - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9])$" + - enum: [ sdc2_clk, sdc2_cmd, sdc2_data, ufs_reset ] + minItems: 1 + maxItems: 36 + + function: + description: + Specify the alternative function to be configured for the specified + pins. + + enum: [ aoss_cti, atest, audio_ref, cam_mclk, cci_async, cci_i2c, + cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4, cri_trng, + cri_trng0, cri_trng1, dbg_out, ddr_bist, ddr_pxi0, ddr_pxi1, + ddr_pxi2, ddr_pxi3, dp_hot, dp_lcd, gcc_gp1, gcc_gp2, gcc_gp3, gpio, + ibi_i3c, jitter_bist, lpass_slimbus, mdp_vsync, mdp_vsync0, + mdp_vsync1, mdp_vsync2, mdp_vsync3, mi2s0_data0, mi2s0_data1, + mi2s0_sck, mi2s0_ws, mi2s1_data0, mi2s1_data1, mi2s1_sck, mi2s1_ws, + mi2s2_data0, mi2s2_data1, mi2s2_sck, mi2s2_ws, pci_e0, pci_e1, + pci_e2, phase_flag, pll_bist, pll_bypassnl, pll_clk, pll_reset, + pri_mi2s, prng_rosc, qdss_cti, qdss_gpio, qspi0, qspi1, qspi2, qspi3, + qspi_clk, qspi_cs, qup0, qup1, qup10, qup11, qup12, qup13, qup14, + qup15, qup16, qup17, qup18, qup19, qup2, qup3, qup4, qup5, qup6, + qup7, qup8, qup9, qup_l4, qup_l5, qup_l6, sd_write, sdc40, sdc41, + sdc42, sdc43, sdc4_clk, sdc4_cmd, sec_mi2s, sp_cmu, tgu_ch0, tgu_ch1, + tgu_ch2, tgu_ch3, tsense_pwm1, tsense_pwm2, tsif0_clk, tsif0_data, + tsif0_en, tsif0_error, tsif0_sync, tsif1_clk, tsif1_data, tsif1_en, + tsif1_error, tsif1_sync, usb2phy_ac, usb_phy, vsense_trigger ] + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + default: 2 + description: + Selects the drive strength for the specified pins, in mA. + + bias-pull-down: true + + bias-pull-up: true + + bias-disable: true + + output-high: true + + output-low: true + + required: + - pins + - function + + additionalProperties: false + +required: + - compatible + - reg + - reg-names + - interrupts + - interrupt-controller + - '#interrupt-cells' + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + pinctrl@1f00000 { + compatible = "qcom,sm8250-pinctrl"; + reg = <0x0f100000 0x300000>, + <0x0f500000 0x300000>, + <0x0f900000 0x300000>; + reg-names = "west", "south", "north"; + interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + gpio-ranges = <&tlmm 0 0 180>; + wakeup-parent = <&pdc>; + }; diff --git a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt index 6eada23eaa31..b68613188c19 100644 --- a/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt @@ -13,6 +13,7 @@ Required Properties: - "renesas,pfc-emev2": for EMEV2 (EMMA Mobile EV2) compatible pin-controller. - "renesas,pfc-r8a73a4": for R8A73A4 (R-Mobile APE6) compatible pin-controller. - "renesas,pfc-r8a7740": for R8A7740 (R-Mobile A1) compatible pin-controller. + - "renesas,pfc-r8a7742": for R8A7742 (RZ/G1H) compatible pin-controller. - "renesas,pfc-r8a7743": for R8A7743 (RZ/G1M) compatible pin-controller. - "renesas,pfc-r8a7744": for R8A7744 (RZ/G1N) compatible pin-controller. - "renesas,pfc-r8a7745": for R8A7745 (RZ/G1E) compatible pin-controller. diff --git a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt index 2113cfaa26e6..d3eae61a340d 100644 --- a/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt +++ b/Documentation/devicetree/bindings/pinctrl/rockchip,pinctrl.txt @@ -110,8 +110,8 @@ pinctrl@20008000 { uart2 { uart2_xfer: uart2-xfer { - rockchip,pins = <RK_GPIO1 8 1 &pcfg_pull_default>, - <RK_GPIO1 9 1 &pcfg_pull_default>; + rockchip,pins = <1 RK_PB0 1 &pcfg_pull_default>, + <1 RK_PB1 1 &pcfg_pull_default>; }; }; }; diff --git a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml index 1f6e51891ddc..0857cbeeb43c 100644 --- a/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml +++ b/Documentation/devicetree/bindings/pinctrl/st,stm32-pinctrl.yaml @@ -36,6 +36,9 @@ properties: pins-are-numbered: true hwlocks: true + interrupts: + maxItems: 1 + st,syscfg: description: Should be phandle/offset/mask - Phandle to the syscon node which includes IRQ mux selection. |