diff options
Diffstat (limited to 'Documentation/kernel-parameters.txt')
| -rw-r--r-- | Documentation/kernel-parameters.txt | 58 |
1 files changed, 55 insertions, 3 deletions
diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt index 5ba4d9dff113..e4cbca58536c 100644 --- a/Documentation/kernel-parameters.txt +++ b/Documentation/kernel-parameters.txt @@ -54,6 +54,7 @@ parameter is applicable: IMA Integrity measurement architecture is enabled. IOSCHED More than one I/O scheduler is enabled. IP_PNP IP DHCP, BOOTP, or RARP is enabled. + IPV6 IPv6 support is enabled. ISAPNP ISA PnP code is enabled. ISDN Appropriate ISDN support is enabled. JOY Appropriate joystick support is enabled. @@ -240,7 +241,7 @@ and is between 256 and 4096 characters. It is defined in the file acpi_sleep= [HW,ACPI] Sleep options Format: { s3_bios, s3_mode, s3_beep, s4_nohwsig, - old_ordering, s4_nonvs } + old_ordering, s4_nonvs, sci_force_enable } See Documentation/power/video.txt for information on s3_bios and s3_mode. s3_beep is for debugging; it makes the PC's speaker beep @@ -253,6 +254,9 @@ and is between 256 and 4096 characters. It is defined in the file of _PTS is used by default). s4_nonvs prevents the kernel from saving/restoring the ACPI NVS memory during hibernation. + sci_force_enable causes the kernel to set SCI_EN directly + on resume from S1/S3 (which is against the ACPI spec, + but some broken systems don't work without it). acpi_use_timer_override [HW,ACPI] Use timer override. For some broken Nvidia NF5 boards @@ -308,6 +312,11 @@ and is between 256 and 4096 characters. It is defined in the file aic79xx= [HW,SCSI] See Documentation/scsi/aic79xx.txt. + alignment= [KNL,ARM] + Allow the default userspace alignment fault handler + behaviour to be specified. Bit 0 enables warnings, + bit 1 enables fixups, and bit 2 sends a segfault. + amd_iommu= [HW,X86-84] Pass parameters to the AMD IOMMU driver in the system. Possible values are: @@ -344,6 +353,9 @@ and is between 256 and 4096 characters. It is defined in the file Change the amount of debugging information output when initialising the APIC and IO-APIC components. + autoconf= [IPV6] + See Documentation/networking/ipv6.txt. + show_lapic= [APIC,X86] Advanced Programmable Interrupt Controller Limit apic dumping. The parameter defines the maximal number of local apics being dumped. Also it is possible @@ -626,6 +638,12 @@ and is between 256 and 4096 characters. It is defined in the file See drivers/char/README.epca and Documentation/serial/digiepca.txt. + disable= [IPV6] + See Documentation/networking/ipv6.txt. + + disable_ipv6= [IPV6] + See Documentation/networking/ipv6.txt. + disable_mtrr_cleanup [X86] The kernel tries to adjust MTRR layout from continuous to discrete, to make X server driver able to add WB @@ -1726,6 +1744,9 @@ and is between 256 and 4096 characters. It is defined in the file nomfgpt [X86-32] Disable Multi-Function General Purpose Timer usage (for AMD Geode machines). + nopat [X86] Disable PAT (page attribute table extension of + pagetables) support. + norandmaps Don't use address space randomization. Equivalent to echo 0 > /proc/sys/kernel/randomize_va_space @@ -1769,6 +1790,12 @@ and is between 256 and 4096 characters. It is defined in the file purges which is reported from either PAL_VM_SUMMARY or SAL PALO. + nr_cpus= [SMP] Maximum number of processors that an SMP kernel + could support. nr_cpus=n : n >= 1 limits the kernel to + supporting 'n' processors. Later in runtime you can not + use hotplug cpu feature to put more cpu back to online. + just like you compile the kernel NR_CPUS=n + nr_uarts= [SERIAL] maximum number of UARTs to be registered. numa_zonelist_order= [KNL, BOOT] Select zonelist order for NUMA. @@ -1936,8 +1963,12 @@ and is between 256 and 4096 characters. It is defined in the file IRQ routing is enabled. noacpi [X86] Do not use ACPI for IRQ routing or for PCI scanning. - use_crs [X86] Use _CRS for PCI resource - allocation. + use_crs [X86] Use PCI host bridge window information + from ACPI. On BIOSes from 2008 or later, this + is enabled by default. If you need to use this, + please report a bug. + nocrs [X86] Ignore PCI host bridge windows from ACPI. + If you need to use this, please report a bug. routeirq Do IRQ routing for all PCI devices. This is normally done in pci_enable_device(), so this option is a temporary workaround @@ -1986,6 +2017,14 @@ and is between 256 and 4096 characters. It is defined in the file force Enable ASPM even on devices that claim not to support it. WARNING: Forcing ASPM on may cause system lockups. + pcie_pme= [PCIE,PM] Native PCIe PME signaling options: + off Do not use native PCIe PME signaling. + force Use native PCIe PME signaling even if the BIOS refuses + to allow the kernel to control the relevant PCIe config + registers. + nomsi Do not use MSI for native PCIe PME signaling (this makes + all PCIe root ports use INTx for everything). + pcmv= [HW,PCMCIA] BadgePAD 4 pd. [PARIDE] @@ -2691,6 +2730,13 @@ and is between 256 and 4096 characters. It is defined in the file medium is write-protected). Example: quirks=0419:aaf5:rl,0421:0433:rc + userpte= + [X86] Flags controlling user PTE allocations. + + nohigh = do not allocate PTE pages in + HIGHMEM regardless of setting + of CONFIG_HIGHPTE. + vdso= [X86,SH] vdso=2: enable compat VDSO (default with COMPAT_VDSO) vdso=1: enable VDSO (default) @@ -2784,6 +2830,12 @@ and is between 256 and 4096 characters. It is defined in the file default x2apic cluster mode on platforms supporting x2apic. + x86_mrst_timer= [X86-32,APBT] + Choose timer option for x86 Moorestown MID platform. + Two valid options are apbt timer only and lapic timer + plus one apbt timer for broadcast timer. + x86_mrst_timer=apbt_only | lapic_and_apbt + xd= [HW,XT] Original XT pre-IDE (RLL encoded) disks. xd_geo= See header of drivers/block/xd.c. |