3 files changed, 57 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-74x164.txt b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt
new file mode 100644
index 000000000000..cc2608021f26
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-74x164.txt
@@ -0,0 +1,22 @@
+* Generic 8-bits shift register GPIO driver
+
+Required properties:
+- compatible : Should be "fairchild,74hc595"
+- reg : chip select number
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify the gpio polarity:
+      0 = active high
+      1 = active low
+- registers-number: Number of daisy-chained shift registers
+
+Example:
+
+gpio5: gpio5@0 {
+	compatible = "fairchild,74hc595";
+	reg = <0>;
+	gpio-controller;
+	#gpio-cells = <2>;
+	registers-number = <4>;
+	spi-max-frequency = <100000>;
+};
diff --git a/Documentation/devicetree/bindings/gpio/gpio-adnp.txt b/Documentation/devicetree/bindings/gpio/gpio-adnp.txt
new file mode 100644
index 000000000000..af66b2724837
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/gpio-adnp.txt
@@ -0,0 +1,34 @@
+Avionic Design N-bit GPIO expander bindings
+
+Required properties:
+- compatible: should be "ad,gpio-adnp"
+- reg: The I2C slave address for this device.
+- interrupt-parent: phandle of the parent interrupt controller.
+- interrupts: Interrupt specifier for the controllers interrupt.
+- #gpio-cells: Should be 2. The first cell is the GPIO number and the
+  second cell is used to specify optional parameters:
+  - bit 0: polarity (0: normal, 1: inverted)
+- gpio-controller: Marks the device as a GPIO controller
+- nr-gpios: The number of pins supported by the controller.
+
+The GPIO expander can optionally be used as an interrupt controller, in
+which case it uses the default two cell specifier as described in
+Documentation/devicetree/bindings/interrupt-controller/interrupts.txt.
+
+Example:
+
+	gpioext: gpio-controller@41 {
+		compatible = "ad,gpio-adnp";
+		reg = <0x41>;
+
+		interrupt-parent = <&gpio>;
+		interrupts = <160 1>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		nr-gpios = <64>;
+	};
diff --git a/Documentation/devicetree/bindings/gpio/led.txt b/Documentation/devicetree/bindings/gpio/led.txt
index 9bb308abd221..edc83c1c0d54 100644
--- a/Documentation/devicetree/bindings/gpio/led.txt
+++ b/Documentation/devicetree/bindings/gpio/led.txt
@@ -8,7 +8,7 @@ node's name represents the name of the corresponding LED.
 
 LED sub-node properties:
 - gpios :  Should specify the LED's GPIO, see "gpios property" in
-  Documentation/devicetree/gpio.txt.  Active low LEDs should be
+  Documentation/devicetree/bindings/gpio/gpio.txt.  Active low LEDs should be
   indicated using flags in the GPIO specifier.
 - label :  (optional) The label for this LED.  If omitted, the label is
   taken from the node name (excluding the unit address).