diff options
Diffstat (limited to 'Documentation/devicetree')
9 files changed, 263 insertions, 1 deletions
diff --git a/Documentation/devicetree/bindings/sound/cs4349.txt b/Documentation/devicetree/bindings/sound/cs4349.txt new file mode 100644 index 000000000000..54c117b59dba --- /dev/null +++ b/Documentation/devicetree/bindings/sound/cs4349.txt @@ -0,0 +1,19 @@ +CS4349 audio CODEC + +Required properties: + + - compatible : "cirrus,cs4349" + + - reg : the I2C address of the device for I2C + +Optional properties: + + - reset-gpios : a GPIO spec for the reset pin. + +Example: + +codec: cs4349@48 { + compatible = "cirrus,cs4349"; + reg = <0x48>; + reset-gpios = <&gpio 54 0>; +}; diff --git a/Documentation/devicetree/bindings/sound/ics43432.txt b/Documentation/devicetree/bindings/sound/ics43432.txt new file mode 100644 index 000000000000..b02e3a6c0fef --- /dev/null +++ b/Documentation/devicetree/bindings/sound/ics43432.txt @@ -0,0 +1,17 @@ +Invensense ICS-43432 MEMS microphone with I2S output. + +There are no software configuration options for this device, indeed, the only +host connection is the I2S interface. Apart from requirements on clock +frequency (460 kHz to 3.379 MHz according to the data sheet) there must be +64 clock cycles in each stereo output frame; 24 of the 32 available bits +contain audio data. A hardware pin determines if the device outputs data +on the left or right channel of the I2S frame. + +Required properties: + - compatible : Must be "invensense,ics43432" + +Example: + + ics43432: ics43432 { + compatible = "invensense,ics43432"; + }; diff --git a/Documentation/devicetree/bindings/sound/max98357a.txt b/Documentation/devicetree/bindings/sound/max98357a.txt index a7a149a236e5..28645a2ff885 100644 --- a/Documentation/devicetree/bindings/sound/max98357a.txt +++ b/Documentation/devicetree/bindings/sound/max98357a.txt @@ -4,7 +4,11 @@ This node models the Maxim MAX98357A DAC. Required properties: - compatible : "maxim,max98357a" -- sdmode-gpios : GPIO specifier for the GPIO -> DAC SDMODE pin + +Optional properties: +- sdmode-gpios : GPIO specifier for the chip's SD_MODE pin. + If this option is not specified then driver does not manage + the pin state (e.g. chip is always on). Example: diff --git a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt index b6b3a786855f..1173395b5e5c 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsnd.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsnd.txt @@ -18,6 +18,12 @@ Required properties: - rcar_sound,src : Should contain SRC feature. The number of SRC subnode should be same as HW. see below for detail. +- rcar_sound,ctu : Should contain CTU feature. + The number of CTU subnode should be same as HW. + see below for detail. +- rcar_sound,mix : Should contain MIX feature. + The number of MIX subnode should be same as HW. + see below for detail. - rcar_sound,dvc : Should contain DVC feature. The number of DVC subnode should be same as HW. see below for detail. @@ -90,6 +96,22 @@ rcar_sound: sound@ec500000 { }; }; + rcar_sound,mix { + mix0: mix@0 { }; + mix1: mix@1 { }; + }; + + rcar_sound,ctu { + ctu00: ctu@0 { }; + ctu01: ctu@1 { }; + ctu02: ctu@2 { }; + ctu03: ctu@3 { }; + ctu10: ctu@4 { }; + ctu11: ctu@5 { }; + ctu12: ctu@6 { }; + ctu13: ctu@7 { }; + }; + rcar_sound,src { src0: src@0 { interrupts = <0 352 IRQ_TYPE_LEVEL_HIGH>; diff --git a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt index c64155027288..962748a8d919 100644 --- a/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt +++ b/Documentation/devicetree/bindings/sound/renesas,rsrc-card.txt @@ -6,6 +6,7 @@ Required properties: - compatible : "renesas,rsrc-card,<board>" Examples with soctypes are: + - "renesas,rsrc-card" - "renesas,rsrc-card,lager" - "renesas,rsrc-card,koelsch" Optional properties: @@ -29,6 +30,12 @@ Optional subnode properties: - frame-inversion : bool property. Add this if the dai-link uses frame clock inversion. - convert-rate : platform specified sampling rate convert +- audio-prefix : see audio-routing +- audio-routing : A list of the connections between audio components. + Each entry is a pair of strings, the first being the connection's sink, + the second being the connection's source. Valid names for sources. + use audio-prefix if some components is using same sink/sources naming. + it can be used if compatible was "renesas,rsrc-card"; Required CPU/CODEC subnodes properties: diff --git a/Documentation/devicetree/bindings/sound/rockchip-max98090.txt b/Documentation/devicetree/bindings/sound/rockchip-max98090.txt new file mode 100644 index 000000000000..a805aa99ad75 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rockchip-max98090.txt @@ -0,0 +1,19 @@ +ROCKCHIP with MAX98090 CODEC + +Required properties: +- compatible: "rockchip,rockchip-audio-max98090" +- rockchip,model: The user-visible name of this sound complex +- rockchip,i2s-controller: The phandle of the Rockchip I2S controller that's + connected to the CODEC +- rockchip,audio-codec: The phandle of the MAX98090 audio codec +- rockchip,headset-codec: The phandle of Ext chip for jack detection + +Example: + +sound { + compatible = "rockchip,rockchip-audio-max98090"; + rockchip,model = "ROCKCHIP-I2S"; + rockchip,i2s-controller = <&i2s>; + rockchip,audio-codec = <&max98090>; + rockchip,headset-codec = <&headsetcodec>; +}; diff --git a/Documentation/devicetree/bindings/sound/rockchip-rt5645.txt b/Documentation/devicetree/bindings/sound/rockchip-rt5645.txt new file mode 100644 index 000000000000..411a62b3ff41 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/rockchip-rt5645.txt @@ -0,0 +1,17 @@ +ROCKCHIP with RT5645/RT5650 CODECS + +Required properties: +- compatible: "rockchip,rockchip-audio-rt5645" +- rockchip,model: The user-visible name of this sound complex +- rockchip,i2s-controller: The phandle of the Rockchip I2S controller that's + connected to the CODEC +- rockchip,audio-codec: The phandle of the RT5645/RT5650 audio codec + +Example: + +sound { + compatible = "rockchip,rockchip-audio-rt5645"; + rockchip,model = "ROCKCHIP-I2S"; + rockchip,i2s-controller = <&i2s>; + rockchip,audio-codec = <&rt5645>; +}; diff --git a/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt new file mode 100644 index 000000000000..028fa1c82f50 --- /dev/null +++ b/Documentation/devicetree/bindings/sound/st,sti-asoc-card.txt @@ -0,0 +1,155 @@ +STMicroelectronics sti ASoC cards + +The sti ASoC Sound Card can be used, for all sti SoCs using internal sti-sas +codec or external codecs. + +sti sound drivers allows to expose sti SoC audio interface through the +generic ASoC simple card. For details about sound card declaration please refer to +Documentation/devicetree/bindings/sound/simple-card.txt. + +1) sti-uniperiph-dai: audio dai device. +--------------------------------------- + +Required properties: + - compatible: "st,sti-uni-player" or "st,sti-uni-reader" + + - st,syscfg: phandle to boot-device system configuration registers + + - clock-names: name of the clocks listed in clocks property in the same order + + - reg: CPU DAI IP Base address and size entries, listed in same + order than the CPU_DAI properties. + + - reg-names: names of the mapped memory regions listed in regs property in + the same order. + + - interrupts: CPU_DAI interrupt line, listed in the same order than the + CPU_DAI properties. + + - dma: CPU_DAI DMA controller phandle and DMA request line, listed in the same + order than the CPU_DAI properties. + + - dma-names: identifier string for each DMA request line in the dmas property. + "tx" for "st,sti-uni-player" compatibility + "rx" for "st,sti-uni-reader" compatibility + + - version: IP version integrated in SOC. + + - dai-name: DAI name that describes the IP. + +Required properties ("st,sti-uni-player" compatibility only): + - clocks: CPU_DAI IP clock source, listed in the same order than the + CPU_DAI properties. + + - uniperiph-id: internal SOC IP instance ID. + + - IP mode: IP working mode depending on associated codec. + "HDMI" connected to HDMI codec IP and IEC HDMI formats. + "SPDIF"connected to SPDIF codec and support SPDIF formats. + "PCM" PCM standard mode for I2S or TDM bus. + +Optional properties: + - pinctrl-0: defined for CPU_DAI@1 and CPU_DAI@4 to describe I2S PIOs for + external codecs connection. + + - pinctrl-names: should contain only one value - "default". + +Example: + + sti_uni_player2: sti-uni-player@2 { + compatible = "st,sti-uni-player"; + status = "okay"; + #sound-dai-cells = <0>; + st,syscfg = <&syscfg_core>; + clocks = <&clk_s_d0_flexgen CLK_PCM_2>; + reg = <0x8D82000 0x158>; + interrupts = <GIC_SPI 86 IRQ_TYPE_NONE>; + dmas = <&fdma0 4 0 1>; + dai-name = "Uni Player #1 (DAC)"; + dma-names = "tx"; + uniperiph-id = <2>; + version = <5>; + mode = "PCM"; + }; + + sti_uni_player3: sti-uni-player@3 { + compatible = "st,sti-uni-player"; + status = "okay"; + #sound-dai-cells = <0>; + st,syscfg = <&syscfg_core>; + clocks = <&clk_s_d0_flexgen CLK_SPDIFF>; + reg = <0x8D85000 0x158>; + interrupts = <GIC_SPI 89 IRQ_TYPE_NONE>; + dmas = <&fdma0 7 0 1>; + dma-names = "tx"; + dai-name = "Uni Player #1 (PIO)"; + uniperiph-id = <3>; + version = <5>; + mode = "SPDIF"; + }; + + sti_uni_reader1: sti-uni-reader@1 { + compatible = "st,sti-uni-reader"; + status = "disabled"; + #sound-dai-cells = <0>; + st,syscfg = <&syscfg_core>; + reg = <0x8D84000 0x158>; + interrupts = <GIC_SPI 88 IRQ_TYPE_NONE>; + dmas = <&fdma0 6 0 1>; + dma-names = "rx"; + dai-name = "Uni Reader #1 (HDMI RX)"; + version = <3>; + }; + +2) sti-sas-codec: internal audio codec IPs driver +------------------------------------------------- + +Required properties: + - compatible: "st,sti<chip>-sas-codec" . + Should be chip "st,stih416-sas-codec" or "st,stih407-sas-codec" + + - st,syscfg: phandle to boot-device system configuration registers. + + - pinctrl-0: SPDIF PIO description. + + - pinctrl-names: should contain only one value - "default". + +Example: + sti_sas_codec: sti-sas-codec { + compatible = "st,stih407-sas-codec"; + #sound-dai-cells = <1>; + st,reg_audio = <&syscfg_core>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spdif_out >; + }; + +Example of audio card declaration: + sound { + compatible = "simple-audio-card"; + simple-audio-card,name = "sti audio card"; + status = "okay"; + + simple-audio-card,dai-link@0 { + /* DAC */ + format = "i2s"; + dai-tdm-slot-width = <32>; + cpu { + sound-dai = <&sti_uni_player2>; + }; + + codec { + sound-dai = <&sti_sasg_codec 1>; + }; + }; + simple-audio-card,dai-link@1 { + /* SPDIF */ + format = "left_j"; + cpu { + sound-dai = <&sti_uni_player3>; + }; + + codec { + sound-dai = <&sti_sasg_codec 0>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 80a72099ed76..2a85b156f997 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -111,6 +111,7 @@ ingenic Ingenic Semiconductor innolux Innolux Corporation intel Intel Corporation intercontrol Inter Control Group +invensense InvenSense Inc. isee ISEE 2007 S.L. isil Intersil jedec JEDEC Solid State Technology Association @@ -155,6 +156,7 @@ nvidia NVIDIA nxp NXP Semiconductors onnn ON Semiconductor Corp. opencores OpenCores.org +option Option NV ortustech Ortus Technology Co., Ltd. ovti OmniVision Technologies panasonic Panasonic Corporation |