diff options
Diffstat (limited to 'Documentation/devicetree/bindings/watchdog')
4 files changed, 85 insertions, 5 deletions
diff --git a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt index fcdd48f7dcff..f90e294d7631 100644 --- a/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/atmel-wdt.txt @@ -9,11 +9,37 @@ Required properties: Optional properties: - timeout-sec: contains the watchdog timeout in seconds. +- interrupts : Should contain WDT interrupt. +- atmel,max-heartbeat-sec : Should contain the maximum heartbeat value in + seconds. This value should be less or equal to 16. It is used to + compute the WDV field. +- atmel,min-heartbeat-sec : Should contain the minimum heartbeat value in + seconds. This value must be smaller than the max-heartbeat-sec value. + It is used to compute the WDD field. +- atmel,watchdog-type : Should be "hardware" or "software". Hardware watchdog + use the at91 watchdog reset. Software watchdog use the watchdog + interrupt to trigger a software reset. +- atmel,reset-type : Should be "proc" or "all". + "all" : assert peripherals and processor reset signals + "proc" : assert the processor reset signal + This is valid only when using "hardware" watchdog. +- atmel,disable : Should be present if you want to disable the watchdog. +- atmel,idle-halt : Should be present if you want to stop the watchdog when + entering idle state. +- atmel,dbg-halt : Should be present if you want to stop the watchdog when + entering debug state. Example: - watchdog@fffffd40 { compatible = "atmel,at91sam9260-wdt"; reg = <0xfffffd40 0x10>; - timeout-sec = <10>; + interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>; + timeout-sec = <15>; + atmel,watchdog-type = "hardware"; + atmel,reset-type = "all"; + atmel,dbg-halt; + atmel,idle-halt; + atmel,max-heartbeat-sec = <16>; + atmel,min-heartbeat-sec = <0>; + status = "okay"; }; diff --git a/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt b/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt index 75558ccd9a05..e60b9a13bdcb 100644 --- a/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/davinci-wdt.txt @@ -1,12 +1,24 @@ -DaVinci Watchdog Timer (WDT) Controller +Texas Instruments DaVinci/Keystone Watchdog Timer (WDT) Controller Required properties: -- compatible : Should be "ti,davinci-wdt" +- compatible : Should be "ti,davinci-wdt", "ti,keystone-wdt" - reg : Should contain WDT registers location and length +Optional properties: +- timeout-sec : Contains the watchdog timeout in seconds +- clocks : the clock feeding the watchdog timer. + Needed if platform uses clocks. + See clock-bindings.txt + +Documentation: +Davinci DM646x - http://www.ti.com/lit/ug/spruer5b/spruer5b.pdf +Keystone - http://www.ti.com/lit/ug/sprugv5a/sprugv5a.pdf + Examples: wdt: wdt@2320000 { compatible = "ti,davinci-wdt"; reg = <0x02320000 0x80>; + timeout-sec = <30>; + clocks = <&clkwdtimer0>; }; diff --git a/Documentation/devicetree/bindings/watchdog/gpio-wdt.txt b/Documentation/devicetree/bindings/watchdog/gpio-wdt.txt new file mode 100644 index 000000000000..37afec194949 --- /dev/null +++ b/Documentation/devicetree/bindings/watchdog/gpio-wdt.txt @@ -0,0 +1,23 @@ +* GPIO-controlled Watchdog + +Required Properties: +- compatible: Should contain "linux,wdt-gpio". +- gpios: From common gpio binding; gpio connection to WDT reset pin. +- hw_algo: The algorithm used by the driver. Should be one of the + following values: + - toggle: Either a high-to-low or a low-to-high transition clears + the WDT counter. The watchdog timer is disabled when GPIO is + left floating or connected to a three-state buffer. + - level: Low or high level starts counting WDT timeout, + the opposite level disables the WDT. Active level is determined + by the GPIO flags. +- hw_margin_ms: Maximum time to reset watchdog circuit (milliseconds). + +Example: + watchdog: watchdog { + /* ADM706 */ + compatible = "linux,wdt-gpio"; + gpios = <&gpio3 9 GPIO_ACTIVE_LOW>; + hw_algo = "toggle"; + hw_margin_ms = <1600>; + }; diff --git a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt index 2aa486cc1ff6..cfff37511aac 100644 --- a/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt +++ b/Documentation/devicetree/bindings/watchdog/samsung-wdt.txt @@ -5,10 +5,29 @@ after a preset amount of time during which the WDT reset event has not occurred. Required properties: -- compatible : should be "samsung,s3c2410-wdt" +- compatible : should be one among the following + (a) "samsung,s3c2410-wdt" for Exynos4 and previous SoCs + (b) "samsung,exynos5250-wdt" for Exynos5250 + (c) "samsung,exynos5420-wdt" for Exynos5420 + - reg : base physical address of the controller and length of memory mapped region. - interrupts : interrupt number to the cpu. +- samsung,syscon-phandle : reference to syscon node (This property required only + in case of compatible being "samsung,exynos5250-wdt" or "samsung,exynos5420-wdt". + In case of Exynos5250 and 5420 this property points to syscon node holding the PMU + base address) Optional properties: - timeout-sec : contains the watchdog timeout in seconds. + +Example: + +watchdog@101D0000 { + compatible = "samsung,exynos5250-wdt"; + reg = <0x101D0000 0x100>; + interrupts = <0 42 0>; + clocks = <&clock 336>; + clock-names = "watchdog"; + samsung,syscon-phandle = <&pmu_syscon>; +}; |