Merge branch 'e1000-7.0.38-k4' of git://lost.foo-projects.org/~ahkok/git/netdev-2.6 into upstream

5 files changed, 104 insertions, 135 deletions

diff --git a/drivers/net/e1000/Makefile b/drivers/net/e1000/Makefile
index 92823ac89d42..5dea2b7dea4d 100644
--- a/drivers/net/e1000/Makefile
+++ b/drivers/net/e1000/Makefile
@@ -1,7 +1,7 @@
 ################################################################################
 #
 # 
-# Copyright(c) 1999 - 2003 Intel Corporation. All rights reserved.
+# Copyright(c) 1999 - 2006 Intel Corporation. All rights reserved.
 # 
 # This program is free software; you can redistribute it and/or modify it 
 # under the terms of the GNU General Public License as published by the Free 
diff --git a/drivers/net/e1000/e1000_ethtool.c b/drivers/net/e1000/e1000_ethtool.c
index e48dc578fde2..cfdf0b24ffc1 100644
--- a/drivers/net/e1000/e1000_ethtool.c
+++ b/drivers/net/e1000/e1000_ethtool.c
@@ -865,15 +865,15 @@ static int
 e1000_intr_test(struct e1000_adapter *adapter, uint64_t *data)
 {
 	struct net_device *netdev = adapter->netdev;
- 	uint32_t mask, i=0, shared_int = TRUE;
- 	uint32_t irq = adapter->pdev->irq;
+	uint32_t mask, i=0, shared_int = TRUE;
+	uint32_t irq = adapter->pdev->irq;
 
 	*data = 0;
 
 	/* Hook up test interrupt handler just for this test */
- 	if (!request_irq(irq, &e1000_test_intr, 0, netdev->name, netdev)) {
- 		shared_int = FALSE;
- 	} else if (request_irq(irq, &e1000_test_intr, SA_SHIRQ,
+	if (!request_irq(irq, &e1000_test_intr, 0, netdev->name, netdev)) {
+		shared_int = FALSE;
+	} else if (request_irq(irq, &e1000_test_intr, SA_SHIRQ,
 			      netdev->name, netdev)){
 		*data = 1;
 		return -1;
@@ -889,22 +889,22 @@ e1000_intr_test(struct e1000_adapter *adapter, uint64_t *data)
 		/* Interrupt to test */
 		mask = 1 << i;
 
- 		if (!shared_int) {
- 			/* Disable the interrupt to be reported in
- 			 * the cause register and then force the same
- 			 * interrupt and see if one gets posted.  If
- 			 * an interrupt was posted to the bus, the
- 			 * test failed.
- 			 */
- 			adapter->test_icr = 0;
- 			E1000_WRITE_REG(&adapter->hw, IMC, mask);
- 			E1000_WRITE_REG(&adapter->hw, ICS, mask);
- 			msec_delay(10);
-
- 			if (adapter->test_icr & mask) {
- 				*data = 3;
- 				break;
- 			}
+		if (!shared_int) {
+			/* Disable the interrupt to be reported in
+			 * the cause register and then force the same
+			 * interrupt and see if one gets posted.  If
+			 * an interrupt was posted to the bus, the
+			 * test failed.
+			 */
+			adapter->test_icr = 0;
+			E1000_WRITE_REG(&adapter->hw, IMC, mask);
+			E1000_WRITE_REG(&adapter->hw, ICS, mask);
+			msec_delay(10);
+
+			if (adapter->test_icr & mask) {
+				*data = 3;
+				break;
+			}
 		}
 
 		/* Enable the interrupt to be reported in
@@ -923,7 +923,7 @@ e1000_intr_test(struct e1000_adapter *adapter, uint64_t *data)
 			break;
 		}
 
- 		if (!shared_int) {
+		if (!shared_int) {
 			/* Disable the other interrupts to be reported in
 			 * the cause register and then force the other
 			 * interrupts and see if any get posted.  If
diff --git a/drivers/net/e1000/e1000_hw.c b/drivers/net/e1000/e1000_hw.c
index 4c796e54b840..3959039b16ec 100644
--- a/drivers/net/e1000/e1000_hw.c
+++ b/drivers/net/e1000/e1000_hw.c
@@ -765,7 +765,7 @@ e1000_init_hw(struct e1000_hw *hw)
     }
 
     if (hw->mac_type == e1000_82573) {
-        e1000_enable_tx_pkt_filtering(hw); 
+        e1000_enable_tx_pkt_filtering(hw);
     }
 
     switch (hw->mac_type) {
@@ -861,7 +861,7 @@ e1000_adjust_serdes_amplitude(struct e1000_hw *hw)
 
     if(eeprom_data != EEPROM_RESERVED_WORD) {
         /* Adjust SERDES output amplitude only. */
-        eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK; 
+        eeprom_data &= EEPROM_SERDES_AMPLITUDE_MASK;
         ret_val = e1000_write_phy_reg(hw, M88E1000_PHY_EXT_CTRL, eeprom_data);
         if(ret_val)
             return ret_val;
@@ -1228,7 +1228,7 @@ e1000_copper_link_igp_setup(struct e1000_hw *hw)
 
     if (hw->phy_reset_disable)
         return E1000_SUCCESS;
-    
+
     ret_val = e1000_phy_reset(hw);
     if (ret_val) {
         DEBUGOUT("Error Resetting the PHY\n");
@@ -1370,7 +1370,7 @@ e1000_copper_link_ggp_setup(struct e1000_hw *hw)
     DEBUGFUNC("e1000_copper_link_ggp_setup");
 
     if(!hw->phy_reset_disable) {
-        
+
         /* Enable CRS on TX for half-duplex operation. */
         ret_val = e1000_read_phy_reg(hw, GG82563_PHY_MAC_SPEC_CTRL,
                                      &phy_data);
@@ -1519,7 +1519,7 @@ e1000_copper_link_mgp_setup(struct e1000_hw *hw)
 
     if(hw->phy_reset_disable)
         return E1000_SUCCESS;
-    
+
     /* Enable CRS on TX. This must be set for half-duplex operation. */
     ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_CTRL, &phy_data);
     if(ret_val)
@@ -1665,7 +1665,7 @@ e1000_copper_link_autoneg(struct e1000_hw *hw)
 *      collision distance in the Transmit Control Register.
 *   2) Set up flow control on the MAC to that established with
 *      the link partner.
-*   3) Config DSP to improve Gigabit link quality for some PHY revisions.    
+*   3) Config DSP to improve Gigabit link quality for some PHY revisions.
 *
 * hw - Struct containing variables accessed by shared code
 ******************************************************************************/
@@ -1674,7 +1674,7 @@ e1000_copper_link_postconfig(struct e1000_hw *hw)
 {
     int32_t ret_val;
     DEBUGFUNC("e1000_copper_link_postconfig");
-    
+
     if(hw->mac_type >= e1000_82544) {
         e1000_config_collision_dist(hw);
     } else {
@@ -1698,7 +1698,7 @@ e1000_copper_link_postconfig(struct e1000_hw *hw)
             return ret_val;
         }
     }
-                
+
     return E1000_SUCCESS;
 }
 
@@ -1754,11 +1754,11 @@ e1000_setup_copper_link(struct e1000_hw *hw)
     }
 
     if(hw->autoneg) {
-        /* Setup autoneg and flow control advertisement 
-          * and perform autonegotiation */   
+        /* Setup autoneg and flow control advertisement
+          * and perform autonegotiation */
         ret_val = e1000_copper_link_autoneg(hw);
         if(ret_val)
-            return ret_val;           
+            return ret_val;
     } else {
         /* PHY will be set to 10H, 10F, 100H,or 100F
           * depending on value from forced_speed_duplex. */
@@ -1786,7 +1786,7 @@ e1000_setup_copper_link(struct e1000_hw *hw)
             ret_val = e1000_copper_link_postconfig(hw);
             if(ret_val)
                 return ret_val;
-            
+
             DEBUGOUT("Valid link established!!!\n");
             return E1000_SUCCESS;
         }
@@ -1984,7 +1984,7 @@ e1000_phy_setup_autoneg(struct e1000_hw *hw)
 
     DEBUGOUT1("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
 
-    ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);    
+    ret_val = e1000_write_phy_reg(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
     if(ret_val)
         return ret_val;
 
@@ -2273,7 +2273,7 @@ e1000_config_mac_to_phy(struct e1000_hw *hw)
 
     DEBUGFUNC("e1000_config_mac_to_phy");
 
-    /* 82544 or newer MAC, Auto Speed Detection takes care of 
+    /* 82544 or newer MAC, Auto Speed Detection takes care of
     * MAC speed/duplex configuration.*/
     if (hw->mac_type >= e1000_82544)
         return E1000_SUCCESS;
@@ -2292,9 +2292,9 @@ e1000_config_mac_to_phy(struct e1000_hw *hw)
     if(ret_val)
         return ret_val;
 
-    if(phy_data & M88E1000_PSSR_DPLX) 
+    if(phy_data & M88E1000_PSSR_DPLX)
         ctrl |= E1000_CTRL_FD;
-    else 
+    else
         ctrl &= ~E1000_CTRL_FD;
 
     e1000_config_collision_dist(hw);
@@ -2493,10 +2493,10 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw)
                  */
                 if(hw->original_fc == e1000_fc_full) {
                     hw->fc = e1000_fc_full;
-                    DEBUGOUT("Flow Control = FULL.\r\n");
+                    DEBUGOUT("Flow Control = FULL.\n");
                 } else {
                     hw->fc = e1000_fc_rx_pause;
-                    DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
+                    DEBUGOUT("Flow Control = RX PAUSE frames only.\n");
                 }
             }
             /* For receiving PAUSE frames ONLY.
@@ -2512,7 +2512,7 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw)
                     (mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
                     (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
                 hw->fc = e1000_fc_tx_pause;
-                DEBUGOUT("Flow Control = TX PAUSE frames only.\r\n");
+                DEBUGOUT("Flow Control = TX PAUSE frames only.\n");
             }
             /* For transmitting PAUSE frames ONLY.
              *
@@ -2527,7 +2527,7 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw)
                     !(mii_nway_lp_ability_reg & NWAY_LPAR_PAUSE) &&
                     (mii_nway_lp_ability_reg & NWAY_LPAR_ASM_DIR)) {
                 hw->fc = e1000_fc_rx_pause;
-                DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
+                DEBUGOUT("Flow Control = RX PAUSE frames only.\n");
             }
             /* Per the IEEE spec, at this point flow control should be
              * disabled.  However, we want to consider that we could
@@ -2553,10 +2553,10 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw)
                      hw->original_fc == e1000_fc_tx_pause) ||
                     hw->fc_strict_ieee) {
                 hw->fc = e1000_fc_none;
-                DEBUGOUT("Flow Control = NONE.\r\n");
+                DEBUGOUT("Flow Control = NONE.\n");
             } else {
                 hw->fc = e1000_fc_rx_pause;
-                DEBUGOUT("Flow Control = RX PAUSE frames only.\r\n");
+                DEBUGOUT("Flow Control = RX PAUSE frames only.\n");
             }
 
             /* Now we need to do one last check...  If we auto-
@@ -2581,7 +2581,7 @@ e1000_config_fc_after_link_up(struct e1000_hw *hw)
                 return ret_val;
             }
         } else {
-            DEBUGOUT("Copper PHY and Auto Neg has not completed.\r\n");
+            DEBUGOUT("Copper PHY and Auto Neg has not completed.\n");
         }
     }
     return E1000_SUCCESS;
@@ -2764,7 +2764,7 @@ e1000_check_for_link(struct e1000_hw *hw)
             hw->autoneg_failed = 1;
             return 0;
         }
-        DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\r\n");
+        DEBUGOUT("NOT RXing /C/, disable AutoNeg and force link.\n");
 
         /* Disable auto-negotiation in the TXCW register */
         E1000_WRITE_REG(hw, TXCW, (hw->txcw & ~E1000_TXCW_ANE));
@@ -2789,7 +2789,7 @@ e1000_check_for_link(struct e1000_hw *hw)
     else if(((hw->media_type == e1000_media_type_fiber) ||
              (hw->media_type == e1000_media_type_internal_serdes)) &&
             (ctrl & E1000_CTRL_SLU) && (rxcw & E1000_RXCW_C)) {
-        DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\r\n");
+        DEBUGOUT("RXing /C/, enable AutoNeg and stop forcing link.\n");
         E1000_WRITE_REG(hw, TXCW, hw->txcw);
         E1000_WRITE_REG(hw, CTRL, (ctrl & ~E1000_CTRL_SLU));
 
@@ -2852,13 +2852,13 @@ e1000_get_speed_and_duplex(struct e1000_hw *hw,
 
         if(status & E1000_STATUS_FD) {
             *duplex = FULL_DUPLEX;
-            DEBUGOUT("Full Duplex\r\n");
+            DEBUGOUT("Full Duplex\n");
         } else {
             *duplex = HALF_DUPLEX;
-            DEBUGOUT(" Half Duplex\r\n");
+            DEBUGOUT(" Half Duplex\n");
         }
     } else {
-        DEBUGOUT("1000 Mbs, Full Duplex\r\n");
+        DEBUGOUT("1000 Mbs, Full Duplex\n");
         *speed = SPEED_1000;
         *duplex = FULL_DUPLEX;
     }
@@ -2884,7 +2884,7 @@ e1000_get_speed_and_duplex(struct e1000_hw *hw,
         }
     }
 
-    if ((hw->mac_type == e1000_80003es2lan) && 
+    if ((hw->mac_type == e1000_80003es2lan) &&
         (hw->media_type == e1000_media_type_copper)) {
         if (*speed == SPEED_1000)
             ret_val = e1000_configure_kmrn_for_1000(hw);
@@ -3160,7 +3160,7 @@ e1000_read_phy_reg(struct e1000_hw *hw,
     if (e1000_swfw_sync_acquire(hw, swfw))
         return -E1000_ERR_SWFW_SYNC;
 
-    if((hw->phy_type == e1000_phy_igp || 
+    if((hw->phy_type == e1000_phy_igp ||
         hw->phy_type == e1000_phy_igp_2) &&
        (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
         ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
@@ -3299,7 +3299,7 @@ e1000_write_phy_reg(struct e1000_hw *hw,
     if (e1000_swfw_sync_acquire(hw, swfw))
         return -E1000_ERR_SWFW_SYNC;
 
-    if((hw->phy_type == e1000_phy_igp || 
+    if((hw->phy_type == e1000_phy_igp ||
         hw->phy_type == e1000_phy_igp_2) &&
        (reg_addr > MAX_PHY_MULTI_PAGE_REG)) {
         ret_val = e1000_write_phy_reg_ex(hw, IGP01E1000_PHY_PAGE_SELECT,
@@ -3497,22 +3497,22 @@ e1000_phy_hw_reset(struct e1000_hw *hw)
         }
         /* Read the device control register and assert the E1000_CTRL_PHY_RST
          * bit. Then, take it out of reset.
-         * For pre-e1000_82571 hardware, we delay for 10ms between the assert 
+         * For pre-e1000_82571 hardware, we delay for 10ms between the assert
          * and deassert.  For e1000_82571 hardware and later, we instead delay
          * for 50us between and 10ms after the deassertion.
          */
         ctrl = E1000_READ_REG(hw, CTRL);
         E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PHY_RST);
         E1000_WRITE_FLUSH(hw);
-        
-        if (hw->mac_type < e1000_82571) 
+
+        if (hw->mac_type < e1000_82571)
             msec_delay(10);
         else
             udelay(100);
-        
+
         E1000_WRITE_REG(hw, CTRL, ctrl);
         E1000_WRITE_FLUSH(hw);
-        
+
         if (hw->mac_type >= e1000_82571)
             msec_delay(10);
         e1000_swfw_sync_release(hw, swfw);
@@ -3816,7 +3816,7 @@ e1000_phy_m88_get_info(struct e1000_hw *hw,
     /* Check polarity status */
     ret_val = e1000_check_polarity(hw, &polarity);
     if(ret_val)
-        return ret_val; 
+        return ret_val;
     phy_info->cable_polarity = polarity;
 
     ret_val = e1000_read_phy_reg(hw, M88E1000_PHY_SPEC_STATUS, &phy_data);
@@ -4541,14 +4541,14 @@ e1000_read_eeprom_eerd(struct e1000_hw *hw,
 
         E1000_WRITE_REG(hw, EERD, eerd);
         error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_READ);
-        
+
         if(error) {
             break;
         }
         data[i] = (E1000_READ_REG(hw, EERD) >> E1000_EEPROM_RW_REG_DATA);
-      
+
     }
-    
+
     return error;
 }
 
@@ -4574,24 +4574,24 @@ e1000_write_eeprom_eewr(struct e1000_hw *hw,
         return -E1000_ERR_SWFW_SYNC;
 
     for (i = 0; i < words; i++) {
-        register_value = (data[i] << E1000_EEPROM_RW_REG_DATA) | 
-                         ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) | 
+        register_value = (data[i] << E1000_EEPROM_RW_REG_DATA) |
+                         ((offset+i) << E1000_EEPROM_RW_ADDR_SHIFT) |
                          E1000_EEPROM_RW_REG_START;
 
         error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE);
         if(error) {
             break;
-        }       
+        }
 
         E1000_WRITE_REG(hw, EEWR, register_value);
-        
+
         error = e1000_poll_eerd_eewr_done(hw, E1000_EEPROM_POLL_WRITE);
-        
+
         if(error) {
             break;
-        }       
+        }
     }
-    
+
     e1000_swfw_sync_release(hw, E1000_SWFW_EEP_SM);
     return error;
 }
@@ -4611,7 +4611,7 @@ e1000_poll_eerd_eewr_done(struct e1000_hw *hw, int eerd)
     for(i = 0; i < attempts; i++) {
         if(eerd == E1000_EEPROM_POLL_READ)
             reg = E1000_READ_REG(hw, EERD);
-        else 
+        else
             reg = E1000_READ_REG(hw, EEWR);
 
         if(reg & E1000_EEPROM_RW_REG_DONE) {
@@ -5136,7 +5136,7 @@ e1000_mc_addr_list_update(struct e1000_hw *hw,
     uint32_t i;
     uint32_t num_rar_entry;
     uint32_t num_mta_entry;
-    
+
     DEBUGFUNC("e1000_mc_addr_list_update");
 
     /* Set the new number of MC addresses that we are being requested to use. */
@@ -6241,7 +6241,7 @@ e1000_check_polarity(struct e1000_hw *hw,
  *                                1 - Downshift ocured.
  *
  * returns: - E1000_ERR_XXX
- *            E1000_SUCCESS 
+ *            E1000_SUCCESS
  *
  * For phy's older then IGP, this function reads the Downshift bit in the Phy
  * Specific Status register.  For IGP phy's, it reads the Downgrade bit in the
@@ -6256,7 +6256,7 @@ e1000_check_downshift(struct e1000_hw *hw)
 
     DEBUGFUNC("e1000_check_downshift");
 
-    if(hw->phy_type == e1000_phy_igp || 
+    if(hw->phy_type == e1000_phy_igp ||
         hw->phy_type == e1000_phy_igp_2) {
         ret_val = e1000_read_phy_reg(hw, IGP01E1000_PHY_LINK_HEALTH,
                                      &phy_data);
@@ -6685,8 +6685,8 @@ e1000_set_d0_lplu_state(struct e1000_hw *hw,
 
 
     } else {
- 
-            phy_data |= IGP02E1000_PM_D0_LPLU;   
+
+            phy_data |= IGP02E1000_PM_D0_LPLU;
             ret_val = e1000_write_phy_reg(hw, IGP02E1000_PHY_POWER_MGMT, phy_data);
             if (ret_val)
                 return ret_val;
@@ -6778,7 +6778,7 @@ int32_t
 e1000_host_if_read_cookie(struct e1000_hw * hw, uint8_t *buffer)
 {
     uint8_t i;
-    uint32_t offset = E1000_MNG_DHCP_COOKIE_OFFSET; 
+    uint32_t offset = E1000_MNG_DHCP_COOKIE_OFFSET;
     uint8_t length = E1000_MNG_DHCP_COOKIE_LENGTH;
 
     length = (length >> 2);
@@ -6797,7 +6797,7 @@ e1000_host_if_read_cookie(struct e1000_hw * hw, uint8_t *buffer)
  * and also checks whether the previous command is completed.
  * It busy waits in case of previous command is not completed.
  *
- * returns: - E1000_ERR_HOST_INTERFACE_COMMAND in case if is not ready or 
+ * returns: - E1000_ERR_HOST_INTERFACE_COMMAND in case if is not ready or
  *            timeout
  *          - E1000_SUCCESS for success.
  ****************************************************************************/
@@ -6821,7 +6821,7 @@ e1000_mng_enable_host_if(struct e1000_hw * hw)
         msec_delay_irq(1);
     }
 
-    if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) { 
+    if (i == E1000_MNG_DHCP_COMMAND_TIMEOUT) {
         DEBUGOUT("Previous command timeout failed .\n");
         return -E1000_ERR_HOST_INTERFACE_COMMAND;
     }
diff --git a/drivers/net/e1000/e1000_hw.h b/drivers/net/e1000/e1000_hw.h
index 03d07ebde4f7..467c9ed944f8 100644
--- a/drivers/net/e1000/e1000_hw.h
+++ b/drivers/net/e1000/e1000_hw.h
@@ -375,7 +375,7 @@ struct e1000_host_mng_dhcp_cookie{
 };
 #endif
 
-int32_t e1000_mng_write_dhcp_info(struct e1000_hw *hw, uint8_t *buffer, 
+int32_t e1000_mng_write_dhcp_info(struct e1000_hw *hw, uint8_t *buffer,
 							uint16_t length);
 boolean_t e1000_check_mng_mode(struct e1000_hw *hw);
 boolean_t e1000_enable_tx_pkt_filtering(struct e1000_hw *hw);
@@ -1802,7 +1802,7 @@ struct e1000_hw {
  *       value2 = [0..64512],    default=4096
  *       value3 = [0..64512],    default=0
  */
-    
+
 #define E1000_PSRCTL_BSIZE0_MASK   0x0000007F
 #define E1000_PSRCTL_BSIZE1_MASK   0x00003F00
 #define E1000_PSRCTL_BSIZE2_MASK   0x003F0000
diff --git a/drivers/net/e1000/e1000_main.c b/drivers/net/e1000/e1000_main.c
index fb8cef619142..258c7d53930e 100644
--- a/drivers/net/e1000/e1000_main.c
+++ b/drivers/net/e1000/e1000_main.c
@@ -29,45 +29,6 @@
 
 #include "e1000.h"
 
-/* Change Log
- * 7.0.33      3-Feb-2006
- *   o Added another fix for the pass false carrier bit
- * 7.0.32      24-Jan-2006
- *   o Need to rebuild with noew version number for the pass false carrier 
- *     fix in e1000_hw.c
- * 7.0.30      18-Jan-2006
- *   o fixup for tso workaround to disable it for pci-x
- *   o fix mem leak on 82542
- *   o fixes for 10 Mb/s connections and incorrect stats
- * 7.0.28      01/06/2006
- *   o hardware workaround to only set "speed mode" bit for 1G link.
- * 7.0.26      12/23/2005
- *   o wake on lan support modified for device ID 10B5
- *   o fix dhcp + vlan issue not making it to the iAMT firmware
- * 7.0.24      12/9/2005
- *   o New hardware support for the Gigabit NIC embedded in the south bridge
- *   o Fixes to the recycling logic (skb->tail) from IBM LTC
- * 6.3.9	12/16/2005
- *   o incorporate fix for recycled skbs from IBM LTC
- * 6.3.7	11/18/2005
- *   o Honor eeprom setting for enabling/disabling Wake On Lan
- * 6.3.5 	11/17/2005
- *   o Fix memory leak in rx ring handling for PCI Express adapters
- * 6.3.4	11/8/05
- *   o Patch from Jesper Juhl to remove redundant NULL checks for kfree
- * 6.3.2	9/20/05
- *   o Render logic that sets/resets DRV_LOAD as inline functions to 
- *     avoid code replication. If f/w is AMT then set DRV_LOAD only when
- *     network interface is open.
- *   o Handle DRV_LOAD set/reset in cases where AMT uses VLANs.
- *   o Adjust PBA partioning for Jumbo frames using MTU size and not
- *     rx_buffer_len
- * 6.3.1	9/19/05
- *   o Use adapter->tx_timeout_factor in Tx Hung Detect logic 
- *      (e1000_clean_tx_irq)
- *   o Support for 8086:10B5 device (Quad Port)
- */
-
 char e1000_driver_name[] = "e1000";
 static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver";
 #ifndef CONFIG_E1000_NAPI
@@ -75,7 +36,7 @@ static char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver";
 #else
 #define DRIVERNAPI "-NAPI"
 #endif
-#define DRV_VERSION "7.0.38-k2"DRIVERNAPI
+#define DRV_VERSION "7.0.38-k4"DRIVERNAPI
 char e1000_driver_version[] = DRV_VERSION;
 static char e1000_copyright[] = "Copyright (c) 1999-2006 Intel Corporation.";
 
@@ -221,6 +182,7 @@ static void e1000_restore_vlan(struct e1000_adapter *adapter);
 static int e1000_suspend(struct pci_dev *pdev, pm_message_t state);
 static int e1000_resume(struct pci_dev *pdev);
 #endif
+static void e1000_shutdown(struct pci_dev *pdev);
 
 #ifdef CONFIG_NET_POLL_CONTROLLER
 /* for netdump / net console */
@@ -236,8 +198,9 @@ static struct pci_driver e1000_driver = {
 	/* Power Managment Hooks */
 #ifdef CONFIG_PM
 	.suspend  = e1000_suspend,
-	.resume   = e1000_resume
+	.resume   = e1000_resume,
 #endif
+	.shutdown = e1000_shutdown
 };
 
 MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
@@ -347,7 +310,7 @@ e1000_update_mng_vlan(struct e1000_adapter *adapter)
  * For ASF and Pass Through versions of f/w this means that the
  * driver is no longer loaded. For AMT version (only with 82573) i
  * of the f/w this means that the netowrk i/f is closed.
- * 
+ *
  **/
 
 static void
@@ -379,10 +342,10 @@ e1000_release_hw_control(struct e1000_adapter *adapter)
  * @adapter: address of board private structure
  *
  * e1000_get_hw_control sets {CTRL_EXT|FWSM}:DRV_LOAD bit.
- * For ASF and Pass Through versions of f/w this means that 
- * the driver is loaded. For AMT version (only with 82573) 
+ * For ASF and Pass Through versions of f/w this means that
+ * the driver is loaded. For AMT version (only with 82573)
  * of the f/w this means that the netowrk i/f is open.
- * 
+ *
  **/
 
 static void
@@ -712,8 +675,8 @@ e1000_probe(struct pci_dev *pdev,
 		DPRINTK(PROBE, INFO, "PHY reset is blocked due to SOL/IDER session.\n");
 
 	/* if ksp3, indicate if it's port a being setup */
-	if (pdev->device == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 && 
-			e1000_ksp3_port_a == 0) 
+	if (pdev->device == E1000_DEV_ID_82546GB_QUAD_COPPER_KSP3 &&
+			e1000_ksp3_port_a == 0)
 		adapter->ksp3_port_a = 1;
 	e1000_ksp3_port_a++;
 	/* Reset for multiple KP3 adapters */
@@ -741,9 +704,9 @@ e1000_probe(struct pci_dev *pdev,
 	if (pci_using_dac)
 		netdev->features |= NETIF_F_HIGHDMA;
 
- 	/* hard_start_xmit is safe against parallel locking */
- 	netdev->features |= NETIF_F_LLTX; 
- 
+	/* hard_start_xmit is safe against parallel locking */
+	netdev->features |= NETIF_F_LLTX;
+
 	adapter->en_mng_pt = e1000_enable_mng_pass_thru(&adapter->hw);
 
 	/* before reading the EEPROM, reset the controller to
@@ -2771,7 +2734,7 @@ e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
 	unsigned int nr_frags = 0;
 	unsigned int mss = 0;
 	int count = 0;
- 	int tso;
+	int tso;
 	unsigned int f;
 	len -= skb->data_len;
 
@@ -2784,7 +2747,7 @@ e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
 
 #ifdef NETIF_F_TSO
 	mss = skb_shinfo(skb)->tso_size;
-	/* The controller does a simple calculation to 
+	/* The controller does a simple calculation to
 	 * make sure there is enough room in the FIFO before
 	 * initiating the DMA for each buffer.  The calc is:
 	 * 4 = ceil(buffer len/mss).  To make sure we don't
@@ -2807,7 +2770,7 @@ e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
 			case e1000_82573:
 				pull_size = min((unsigned int)4, skb->data_len);
 				if (!__pskb_pull_tail(skb, pull_size)) {
-					printk(KERN_ERR 
+					printk(KERN_ERR
 						"__pskb_pull_tail failed.\n");
 					dev_kfree_skb_any(skb);
 					return NETDEV_TX_OK;
@@ -3753,7 +3716,7 @@ e1000_clean_rx_irq_ps(struct e1000_adapter *adapter,
 		 * throughput, so unsplit small packets and save the alloc/put*/
 		if (l1 && ((length + l1) <= adapter->rx_ps_bsize0)) {
 			u8 *vaddr;
-			/* there is no documentation about how to call 
+			/* there is no documentation about how to call
 			 * kmap_atomic, so we can't hold the mapping
 			 * very long */
 			pci_dma_sync_single_for_cpu(pdev,
@@ -4605,6 +4568,12 @@ e1000_resume(struct pci_dev *pdev)
 	return 0;
 }
 #endif
+
+static void e1000_shutdown(struct pci_dev *pdev)
+{
+	e1000_suspend(pdev, PMSG_SUSPEND);
+}
+
 #ifdef CONFIG_NET_POLL_CONTROLLER
 /*
  * Polling 'interrupt' - used by things like netconsole to send skbs