Merge tag 'dwc3-for-v3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next

usb: dwc3: patches for v3.5 merge window

This pull request contains one workaround for a Silicon
Issue found on all RTL releases prior to 2.20a, which
would cause a metastability state on Run/Stop bit.

We also have some patches implementing a few extra Standard
requests introduced by USB3 spec (Set SEL and Set Isoch Delay),
as well as one patch, which has been pending for a long time,
implementing LPM support.

Last, but not least, we are splitting the host address space
out of the dwc3 core driver otherwise xHCI won't be able to
request_mem_region() its own address space. This patch is
only needed because we are (as we should) re-using the xHCI
driver, which is a completely separate module.

Together with these three big changes, come a few extra preparatory
patches which most move code around, define macros and so on, as
well as a fix for Isochronous transfers which hasn't been triggered
before.

[ resolved conflicts and build error in drivers/usb/dwc3/gadget.c - gregkh]

8 files changed, 323 insertions, 84 deletions

diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c
index 99b58d84553a..1040bdb8dc88 100644
--- a/drivers/usb/dwc3/core.c
+++ b/drivers/usb/dwc3/core.c
@@ -410,7 +410,6 @@ static int __devinit dwc3_probe(struct platform_device *pdev)
 	struct device		*dev = &pdev->dev;
 
 	int			ret = -ENOMEM;
-	int			irq;
 
 	void __iomem		*regs;
 	void			*mem;
@@ -425,15 +424,28 @@ static int __devinit dwc3_probe(struct platform_device *pdev)
 	dwc = PTR_ALIGN(mem, DWC3_ALIGN_MASK + 1);
 	dwc->mem = mem;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
 	if (!res) {
-		dev_err(dev, "missing resource\n");
+		dev_err(dev, "missing IRQ\n");
 		return -ENODEV;
 	}
+	dwc->xhci_resources[1] = *res;
 
-	dwc->res = res;
-
-	res = devm_request_mem_region(dev, res->start, resource_size(res),
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "missing memory resource\n");
+		return -ENODEV;
+	}
+	dwc->xhci_resources[0] = *res;
+	dwc->xhci_resources[0].end = dwc->xhci_resources[0].start +
+					DWC3_XHCI_REGS_END;
+
+	 /*
+	  * Request memory region but exclude xHCI regs,
+	  * since it will be requested by the xhci-plat driver.
+	  */
+	res = devm_request_mem_region(dev, res->start + DWC3_GLOBALS_REGS_START,
+			resource_size(res) - DWC3_GLOBALS_REGS_START,
 			dev_name(dev));
 	if (!res) {
 		dev_err(dev, "can't request mem region\n");
@@ -446,19 +458,12 @@ static int __devinit dwc3_probe(struct platform_device *pdev)
 		return -ENOMEM;
 	}
 
-	irq = platform_get_irq(pdev, 0);
-	if (irq < 0) {
-		dev_err(dev, "missing IRQ\n");
-		return -ENODEV;
-	}
-
 	spin_lock_init(&dwc->lock);
 	platform_set_drvdata(pdev, dwc);
 
 	dwc->regs	= regs;
 	dwc->regs_size	= resource_size(res);
 	dwc->dev	= dev;
-	dwc->irq	= irq;
 
 	if (!strncmp("super", maximum_speed, 5))
 		dwc->maximum_speed = DWC3_DCFG_SUPERSPEED;
diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index 9c5c73aae4f4..f69c877add09 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -51,7 +51,9 @@
 #include <linux/usb/gadget.h>
 
 /* Global constants */
+#define DWC3_EP0_BOUNCE_SIZE	512
 #define DWC3_ENDPOINTS_NUM	32
+#define DWC3_XHCI_RESOURCES_NUM	2
 
 #define DWC3_EVENT_BUFFERS_SIZE	PAGE_SIZE
 #define DWC3_EVENT_TYPE_MASK	0xfe
@@ -75,6 +77,16 @@
 #define DWC3_GSNPSID_MASK	0xffff0000
 #define DWC3_GSNPSREV_MASK	0xffff
 
+/* DWC3 registers memory space boundries */
+#define DWC3_XHCI_REGS_START		0x0
+#define DWC3_XHCI_REGS_END		0x7fff
+#define DWC3_GLOBALS_REGS_START		0xc100
+#define DWC3_GLOBALS_REGS_END		0xc6ff
+#define DWC3_DEVICE_REGS_START		0xc700
+#define DWC3_DEVICE_REGS_END		0xcbff
+#define DWC3_OTG_REGS_START		0xcc00
+#define DWC3_OTG_REGS_END		0xccff
+
 /* Global Registers */
 #define DWC3_GSBUSCFG0		0xc100
 #define DWC3_GSBUSCFG1		0xc104
@@ -183,6 +195,7 @@
 #define DWC3_GHWPARAMS1_EN_PWROPT_CLK	1
 
 /* Device Configuration Register */
+#define DWC3_DCFG_LPM_CAP	(1 << 22)
 #define DWC3_DCFG_DEVADDR(addr)	((addr) << 3)
 #define DWC3_DCFG_DEVADDR_MASK	DWC3_DCFG_DEVADDR(0x7f)
 
@@ -272,12 +285,14 @@
 #define DWC3_DGCMD_SET_ENDPOINT_NRDY	0x0c
 #define DWC3_DGCMD_RUN_SOC_BUS_LOOPBACK	0x10
 
+#define DWC3_DGCMD_STATUS(n)		(((n) >> 15) & 1)
+#define DWC3_DGCMD_CMDACT		(1 << 10)
+
 /* Device Endpoint Command Register */
 #define DWC3_DEPCMD_PARAM_SHIFT		16
 #define DWC3_DEPCMD_PARAM(x)		((x) << DWC3_DEPCMD_PARAM_SHIFT)
 #define DWC3_DEPCMD_GET_RSC_IDX(x)     (((x) >> DWC3_DEPCMD_PARAM_SHIFT) & 0x7f)
-#define DWC3_DEPCMD_STATUS_MASK		(0x0f << 12)
-#define DWC3_DEPCMD_STATUS(x)		(((x) & DWC3_DEPCMD_STATUS_MASK) >> 12)
+#define DWC3_DEPCMD_STATUS(x)		(((x) >> 15) & 1)
 #define DWC3_DEPCMD_HIPRI_FORCERM	(1 << 11)
 #define DWC3_DEPCMD_CMDACT		(1 << 10)
 #define DWC3_DEPCMD_CMDIOC		(1 << 8)
@@ -560,6 +575,11 @@ struct dwc3_request {
  * @setup_packet_pending: true when there's a Setup Packet in FIFO. Workaround
  * @needs_fifo_resize: not all users might want fifo resizing, flag it
  * @resize_fifos: tells us it's ok to reconfigure our TxFIFO sizes.
+ * @isoch_delay: wValue from Set Isochronous Delay request;
+ * @u2sel: parameter from Set SEL request.
+ * @u2pel: parameter from Set SEL request.
+ * @u1sel: parameter from Set SEL request.
+ * @u1pel: parameter from Set SEL request.
  * @ep0_next_event: hold the next expected event
  * @ep0state: state of endpoint zero
  * @link_state: link state
@@ -582,7 +602,7 @@ struct dwc3 {
 	struct device		*dev;
 
 	struct platform_device	*xhci;
-	struct resource		*res;
+	struct resource		xhci_resources[DWC3_XHCI_RESOURCES_NUM];
 
 	struct dwc3_event_buffer **ev_buffs;
 	struct dwc3_ep		*eps[DWC3_ENDPOINTS_NUM];
@@ -593,8 +613,6 @@ struct dwc3 {
 	void __iomem		*regs;
 	size_t			regs_size;
 
-	int			irq;
-
 	u32			num_event_buffers;
 	u32			u1u2;
 	u32			maximum_speed;
@@ -608,6 +626,10 @@ struct dwc3 {
 #define DWC3_REVISION_185A	0x5533185a
 #define DWC3_REVISION_188A	0x5533188a
 #define DWC3_REVISION_190A	0x5533190a
+#define DWC3_REVISION_200A	0x5533200a
+#define DWC3_REVISION_202A	0x5533202a
+#define DWC3_REVISION_210A	0x5533210a
+#define DWC3_REVISION_220A	0x5533220a
 
 	unsigned		is_selfpowered:1;
 	unsigned		three_stage_setup:1;
@@ -624,7 +646,14 @@ struct dwc3 {
 	enum dwc3_link_state	link_state;
 	enum dwc3_device_state	dev_state;
 
+	u16			isoch_delay;
+	u16			u2sel;
+	u16			u2pel;
+	u8			u1sel;
+	u8			u1pel;
+
 	u8			speed;
+
 	void			*mem;
 
 	struct dwc3_hwparams	hwparams;
diff --git a/drivers/usb/dwc3/dwc3-omap.c b/drivers/usb/dwc3/dwc3-omap.c
index d7d9c0ec9515..479dc047da3a 100644
--- a/drivers/usb/dwc3/dwc3-omap.c
+++ b/drivers/usb/dwc3/dwc3-omap.c
@@ -49,7 +49,6 @@
 #include <linux/of.h>
 
 #include "core.h"
-#include "io.h"
 
 /*
  * All these registers belong to OMAP's Wrapper around the
@@ -143,6 +142,17 @@ struct dwc3_omap {
 	u32			dma_status:1;
 };
 
+static inline u32 dwc3_omap_readl(void __iomem *base, u32 offset)
+{
+	return readl(base + offset);
+}
+
+static inline void dwc3_omap_writel(void __iomem *base, u32 offset, u32 value)
+{
+	writel(value, base + offset);
+}
+
+
 static irqreturn_t dwc3_omap_interrupt(int irq, void *_omap)
 {
 	struct dwc3_omap	*omap = _omap;
@@ -150,7 +160,7 @@ static irqreturn_t dwc3_omap_interrupt(int irq, void *_omap)
 
 	spin_lock(&omap->lock);
 
-	reg = dwc3_readl(omap->base, USBOTGSS_IRQSTATUS_1);
+	reg = dwc3_omap_readl(omap->base, USBOTGSS_IRQSTATUS_1);
 
 	if (reg & USBOTGSS_IRQ1_DMADISABLECLR) {
 		dev_dbg(omap->dev, "DMA Disable was Cleared\n");
@@ -184,10 +194,10 @@ static irqreturn_t dwc3_omap_interrupt(int irq, void *_omap)
 	if (reg & USBOTGSS_IRQ1_IDPULLUP_FALL)
 		dev_dbg(omap->dev, "IDPULLUP Fall\n");
 
-	dwc3_writel(omap->base, USBOTGSS_IRQSTATUS_1, reg);
+	dwc3_omap_writel(omap->base, USBOTGSS_IRQSTATUS_1, reg);
 
-	reg = dwc3_readl(omap->base, USBOTGSS_IRQSTATUS_0);
-	dwc3_writel(omap->base, USBOTGSS_IRQSTATUS_0, reg);
+	reg = dwc3_omap_readl(omap->base, USBOTGSS_IRQSTATUS_0);
+	dwc3_omap_writel(omap->base, USBOTGSS_IRQSTATUS_0, reg);
 
 	spin_unlock(&omap->lock);
 
@@ -270,7 +280,7 @@ static int __devinit dwc3_omap_probe(struct platform_device *pdev)
 	omap->base	= base;
 	omap->dwc3	= dwc3;
 
-	reg = dwc3_readl(omap->base, USBOTGSS_UTMI_OTG_STATUS);
+	reg = dwc3_omap_readl(omap->base, USBOTGSS_UTMI_OTG_STATUS);
 
 	utmi_mode = of_get_property(node, "utmi-mode", &size);
 	if (utmi_mode && size == sizeof(*utmi_mode)) {
@@ -293,10 +303,10 @@ static int __devinit dwc3_omap_probe(struct platform_device *pdev)
 		}
 	}
 
-	dwc3_writel(omap->base, USBOTGSS_UTMI_OTG_STATUS, reg);
+	dwc3_omap_writel(omap->base, USBOTGSS_UTMI_OTG_STATUS, reg);
 
 	/* check the DMA Status */
-	reg = dwc3_readl(omap->base, USBOTGSS_SYSCONFIG);
+	reg = dwc3_omap_readl(omap->base, USBOTGSS_SYSCONFIG);
 	omap->dma_status = !!(reg & USBOTGSS_SYSCONFIG_DMADISABLE);
 
 	/* Set No-Idle and No-Standby */
@@ -306,7 +316,7 @@ static int __devinit dwc3_omap_probe(struct platform_device *pdev)
 	reg |= (USBOTGSS_SYSCONFIG_STANDBYMODE(USBOTGSS_STANDBYMODE_NO_STANDBY)
 		| USBOTGSS_SYSCONFIG_IDLEMODE(USBOTGSS_IDLEMODE_NO_IDLE));
 
-	dwc3_writel(omap->base, USBOTGSS_SYSCONFIG, reg);
+	dwc3_omap_writel(omap->base, USBOTGSS_SYSCONFIG, reg);
 
 	ret = devm_request_irq(dev, omap->irq, dwc3_omap_interrupt, 0,
 			"dwc3-omap", omap);
@@ -318,7 +328,7 @@ static int __devinit dwc3_omap_probe(struct platform_device *pdev)
 
 	/* enable all IRQs */
 	reg = USBOTGSS_IRQO_COREIRQ_ST;
-	dwc3_writel(omap->base, USBOTGSS_IRQENABLE_SET_0, reg);
+	dwc3_omap_writel(omap->base, USBOTGSS_IRQENABLE_SET_0, reg);
 
 	reg = (USBOTGSS_IRQ1_OEVT |
 			USBOTGSS_IRQ1_DRVVBUS_RISE |
@@ -330,7 +340,7 @@ static int __devinit dwc3_omap_probe(struct platform_device *pdev)
 			USBOTGSS_IRQ1_DISCHRGVBUS_FALL |
 			USBOTGSS_IRQ1_IDPULLUP_FALL);
 
-	dwc3_writel(omap->base, USBOTGSS_IRQENABLE_SET_1, reg);
+	dwc3_omap_writel(omap->base, USBOTGSS_IRQENABLE_SET_1, reg);
 
 	ret = platform_device_add_resources(dwc3, pdev->resource,
 			pdev->num_resources);
diff --git a/drivers/usb/dwc3/ep0.c b/drivers/usb/dwc3/ep0.c
index 3453ca1f7479..9e8a3dce69fd 100644
--- a/drivers/usb/dwc3/ep0.c
+++ b/drivers/usb/dwc3/ep0.c
@@ -261,6 +261,7 @@ static int dwc3_ep0_handle_status(struct dwc3 *dwc,
 {
 	struct dwc3_ep		*dep;
 	u32			recip;
+	u32			reg;
 	u16			usb_status = 0;
 	__le16			*response_pkt;
 
@@ -268,10 +269,18 @@ static int dwc3_ep0_handle_status(struct dwc3 *dwc,
 	switch (recip) {
 	case USB_RECIP_DEVICE:
 		/*
-		 * We are self-powered. U1/U2/LTM will be set later
-		 * once we handle this states. RemoteWakeup is 0 on SS
+		 * LTM will be set once we know how to set this in HW.
 		 */
 		usb_status |= dwc->is_selfpowered << USB_DEVICE_SELF_POWERED;
+
+		if (dwc->speed == DWC3_DSTS_SUPERSPEED) {
+			reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+			if (reg & DWC3_DCTL_INITU1ENA)
+				usb_status |= 1 << USB_DEV_STAT_U1_ENABLED;
+			if (reg & DWC3_DCTL_INITU2ENA)
+				usb_status |= 1 << USB_DEV_STAT_U2_ENABLED;
+		}
+
 		break;
 
 	case USB_RECIP_INTERFACE:
@@ -312,6 +321,7 @@ static int dwc3_ep0_handle_feature(struct dwc3 *dwc,
 	u32			recip;
 	u32			wValue;
 	u32			wIndex;
+	u32			reg;
 	int			ret;
 
 	wValue = le16_to_cpu(ctrl->wValue);
@@ -320,29 +330,43 @@ static int dwc3_ep0_handle_feature(struct dwc3 *dwc,
 	switch (recip) {
 	case USB_RECIP_DEVICE:
 
+		switch (wValue) {
+		case USB_DEVICE_REMOTE_WAKEUP:
+			break;
 		/*
 		 * 9.4.1 says only only for SS, in AddressState only for
 		 * default control pipe
 		 */
-		switch (wValue) {
 		case USB_DEVICE_U1_ENABLE:
-		case USB_DEVICE_U2_ENABLE:
-		case USB_DEVICE_LTM_ENABLE:
 			if (dwc->dev_state != DWC3_CONFIGURED_STATE)
 				return -EINVAL;
 			if (dwc->speed != DWC3_DSTS_SUPERSPEED)
 				return -EINVAL;
-		}
 
-		/* XXX add U[12] & LTM */
-		switch (wValue) {
-		case USB_DEVICE_REMOTE_WAKEUP:
-			break;
-		case USB_DEVICE_U1_ENABLE:
+			reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+			if (set)
+				reg |= DWC3_DCTL_INITU1ENA;
+			else
+				reg &= ~DWC3_DCTL_INITU1ENA;
+			dwc3_writel(dwc->regs, DWC3_DCTL, reg);
 			break;
+
 		case USB_DEVICE_U2_ENABLE:
+			if (dwc->dev_state != DWC3_CONFIGURED_STATE)
+				return -EINVAL;
+			if (dwc->speed != DWC3_DSTS_SUPERSPEED)
+				return -EINVAL;
+
+			reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+			if (set)
+				reg |= DWC3_DCTL_INITU2ENA;
+			else
+				reg &= ~DWC3_DCTL_INITU2ENA;
+			dwc3_writel(dwc->regs, DWC3_DCTL, reg);
 			break;
+
 		case USB_DEVICE_LTM_ENABLE:
+			return -EINVAL;
 			break;
 
 		case USB_DEVICE_TEST_MODE:
@@ -469,6 +493,107 @@ static int dwc3_ep0_set_config(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)
 	return ret;
 }
 
+static void dwc3_ep0_set_sel_cmpl(struct usb_ep *ep, struct usb_request *req)
+{
+	struct dwc3_ep	*dep = to_dwc3_ep(ep);
+	struct dwc3	*dwc = dep->dwc;
+
+	u32		param = 0;
+	u32		reg;
+
+	struct timing {
+		u8	u1sel;
+		u8	u1pel;
+		u16	u2sel;
+		u16	u2pel;
+	} __packed timing;
+
+	int		ret;
+
+	memcpy(&timing, req->buf, sizeof(timing));
+
+	dwc->u1sel = timing.u1sel;
+	dwc->u1pel = timing.u1pel;
+	dwc->u2sel = timing.u2sel;
+	dwc->u2pel = timing.u2pel;
+
+	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+	if (reg & DWC3_DCTL_INITU2ENA)
+		param = dwc->u2pel;
+	if (reg & DWC3_DCTL_INITU1ENA)
+		param = dwc->u1pel;
+
+	/*
+	 * According to Synopsys Databook, if parameter is
+	 * greater than 125, a value of zero should be
+	 * programmed in the register.
+	 */
+	if (param > 125)
+		param = 0;
+
+	/* now that we have the time, issue DGCMD Set Sel */
+	ret = dwc3_send_gadget_generic_command(dwc,
+			DWC3_DGCMD_SET_PERIODIC_PAR, param);
+	WARN_ON(ret < 0);
+}
+
+static int dwc3_ep0_set_sel(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)
+{
+	struct dwc3_ep	*dep;
+	u16		wLength;
+	u16		wValue;
+
+	if (dwc->dev_state == DWC3_DEFAULT_STATE)
+		return -EINVAL;
+
+	wValue = le16_to_cpu(ctrl->wValue);
+	wLength = le16_to_cpu(ctrl->wLength);
+
+	if (wLength != 6) {
+		dev_err(dwc->dev, "Set SEL should be 6 bytes, got %d\n",
+				wLength);
+		return -EINVAL;
+	}
+
+	/*
+	 * To handle Set SEL we need to receive 6 bytes from Host. So let's
+	 * queue a usb_request for 6 bytes.
+	 *
+	 * Remember, though, this controller can't handle non-wMaxPacketSize
+	 * aligned transfers on the OUT direction, so we queue a request for
+	 * wMaxPacketSize instead.
+	 */
+	dep = dwc->eps[0];
+	dwc->ep0_usb_req.dep = dep;
+	dwc->ep0_usb_req.request.length = dep->endpoint.maxpacket;
+	dwc->ep0_usb_req.request.buf = dwc->setup_buf;
+	dwc->ep0_usb_req.request.complete = dwc3_ep0_set_sel_cmpl;
+
+	return __dwc3_gadget_ep0_queue(dep, &dwc->ep0_usb_req);
+}
+
+static int dwc3_ep0_set_isoch_delay(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)
+{
+	u16		wLength;
+	u16		wValue;
+	u16		wIndex;
+
+	wValue = le16_to_cpu(ctrl->wValue);
+	wLength = le16_to_cpu(ctrl->wLength);
+	wIndex = le16_to_cpu(ctrl->wIndex);
+
+	if (wIndex || wLength)
+		return -EINVAL;
+
+	/*
+	 * REVISIT It's unclear from Databook what to do with this
+	 * value. For now, just cache it.
+	 */
+	dwc->isoch_delay = wValue;
+
+	return 0;
+}
+
 static int dwc3_ep0_std_request(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)
 {
 	int ret;
@@ -494,6 +619,14 @@ static int dwc3_ep0_std_request(struct dwc3 *dwc, struct usb_ctrlrequest *ctrl)
 		dev_vdbg(dwc->dev, "USB_REQ_SET_CONFIGURATION\n");
 		ret = dwc3_ep0_set_config(dwc, ctrl);
 		break;
+	case USB_REQ_SET_SEL:
+		dev_vdbg(dwc->dev, "USB_REQ_SET_SEL\n");
+		ret = dwc3_ep0_set_sel(dwc, ctrl);
+		break;
+	case USB_REQ_SET_ISOCH_DELAY:
+		dev_vdbg(dwc->dev, "USB_REQ_SET_ISOCH_DELAY\n");
+		ret = dwc3_ep0_set_isoch_delay(dwc, ctrl);
+		break;
 	default:
 		dev_vdbg(dwc->dev, "Forwarding to gadget driver\n");
 		ret = dwc3_ep0_delegate_req(dwc, ctrl);
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 561625a1284d..3df1a1973b05 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -276,6 +276,33 @@ static const char *dwc3_gadget_ep_cmd_string(u8 cmd)
 	}
 }
 
+int dwc3_send_gadget_generic_command(struct dwc3 *dwc, int cmd, u32 param)
+{
+	u32		timeout = 500;
+	u32		reg;
+
+	dwc3_writel(dwc->regs, DWC3_DGCMDPAR, param);
+	dwc3_writel(dwc->regs, DWC3_DGCMD, cmd | DWC3_DGCMD_CMDACT);
+
+	do {
+		reg = dwc3_readl(dwc->regs, DWC3_DGCMD);
+		if (!(reg & DWC3_DGCMD_CMDACT)) {
+			dev_vdbg(dwc->dev, "Command Complete --> %d\n",
+					DWC3_DGCMD_STATUS(reg));
+			return 0;
+		}
+
+		/*
+		 * We can't sleep here, because it's also called from
+		 * interrupt context.
+		 */
+		timeout--;
+		if (!timeout)
+			return -ETIMEDOUT;
+		udelay(1);
+	} while (1);
+}
+
 int dwc3_send_gadget_ep_cmd(struct dwc3 *dwc, unsigned ep,
 		unsigned cmd, struct dwc3_gadget_ep_cmd_params *params)
 {
@@ -929,10 +956,12 @@ static int __dwc3_gadget_kick_transfer(struct dwc3_ep *dep, u16 cmd_param,
 	}
 
 	dep->flags |= DWC3_EP_BUSY;
-	dep->res_trans_idx = dwc3_gadget_ep_get_transfer_index(dwc,
-			dep->number);
 
-	WARN_ON_ONCE(!dep->res_trans_idx);
+	if (start_new) {
+		dep->res_trans_idx = dwc3_gadget_ep_get_transfer_index(dwc,
+				dep->number);
+		WARN_ON_ONCE(!dep->res_trans_idx);
+	}
 
 	return 0;
 }
@@ -966,28 +995,37 @@ static int __dwc3_gadget_ep_queue(struct dwc3_ep *dep, struct dwc3_request *req)
 
 	list_add_tail(&req->list, &dep->request_list);
 
+	if (usb_endpoint_xfer_isoc(dep->endpoint.desc) && (dep->flags & DWC3_EP_BUSY))
+		dep->flags |= DWC3_EP_PENDING_REQUEST;
+
 	/*
-	 * There is one special case: XferNotReady with
-	 * empty list of requests. We need to kick the
-	 * transfer here in that situation, otherwise
-	 * we will be NAKing forever.
+	 * There are two special cases:
+	 *
+	 * 1. XferNotReady with empty list of requests. We need to kick the
+	 *    transfer here in that situation, otherwise we will be NAKing
+	 *    forever. If we get XferNotReady before gadget driver has a
+	 *    chance to queue a request, we will ACK the IRQ but won't be
+	 *    able to receive the data until the next request is queued.
+	 *    The following code is handling exactly that.
 	 *
-	 * If we get XferNotReady before gadget driver
-	 * has a chance to queue a request, we will ACK
-	 * the IRQ but won't be able to receive the data
-	 * until the next request is queued. The following
-	 * code is handling exactly that.
+	 * 2. XferInProgress on Isoc EP with an active transfer. We need to
+	 *    kick the transfer here after queuing a request, otherwise the
+	 *    core may not see the modified TRB(s).
 	 */
 	if (dep->flags & DWC3_EP_PENDING_REQUEST) {
-		int ret;
-		int start_trans;
+		int	ret;
+		int	start_trans = 1;
+		u8	trans_idx = dep->res_trans_idx;
 
-		start_trans = 1;
 		if (usb_endpoint_xfer_isoc(dep->endpoint.desc) &&
-				(dep->flags & DWC3_EP_BUSY))
+				(dep->flags & DWC3_EP_BUSY)) {
 			start_trans = 0;
+			WARN_ON_ONCE(!trans_idx);
+		} else {
+			trans_idx = 0;
+		}
 
-		ret = __dwc3_gadget_kick_transfer(dep, 0, start_trans);
+		ret = __dwc3_gadget_kick_transfer(dep, trans_idx, start_trans);
 		if (ret && ret != -EBUSY) {
 			struct dwc3	*dwc = dep->dwc;
 
@@ -1355,7 +1393,24 @@ static int dwc3_gadget_start(struct usb_gadget *g,
 
 	reg = dwc3_readl(dwc->regs, DWC3_DCFG);
 	reg &= ~(DWC3_DCFG_SPEED_MASK);
-	reg |= dwc->maximum_speed;
+
+	/**
+	 * WORKAROUND: DWC3 revision < 2.20a have an issue
+	 * which would cause metastability state on Run/Stop
+	 * bit if we try to force the IP to USB2-only mode.
+	 *
+	 * Because of that, we cannot configure the IP to any
+	 * speed other than the SuperSpeed
+	 *
+	 * Refers to:
+	 *
+	 * STAR#9000525659: Clock Domain Crossing on DCTL in
+	 * USB 2.0 Mode
+	 */
+	if (dwc->revision < DWC3_REVISION_220A)
+		reg |= DWC3_DCFG_SUPERSPEED;
+	else
+		reg |= dwc->maximum_speed;
 	dwc3_writel(dwc->regs, DWC3_DCFG, reg);
 
 	dwc->start_config_issued = false;
@@ -1915,6 +1970,7 @@ static void dwc3_gadget_reset_interrupt(struct dwc3 *dwc)
 
 	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
 	reg &= ~DWC3_DCTL_TSTCTRL_MASK;
+	reg &= ~(DWC3_DCTL_INITU1ENA | DWC3_DCTL_INITU2ENA);
 	dwc3_writel(dwc->regs, DWC3_DCTL, reg);
 	dwc->test_mode = false;
 
@@ -2262,8 +2318,7 @@ int __devinit dwc3_gadget_init(struct dwc3 *dwc)
 		goto err1;
 	}
 
-	dwc->setup_buf = kzalloc(sizeof(*dwc->setup_buf) * 2,
-			GFP_KERNEL);
+	dwc->setup_buf = kzalloc(DWC3_EP0_BOUNCE_SIZE, GFP_KERNEL);
 	if (!dwc->setup_buf) {
 		dev_err(dwc->dev, "failed to allocate setup buffer\n");
 		ret = -ENOMEM;
@@ -2271,7 +2326,8 @@ int __devinit dwc3_gadget_init(struct dwc3 *dwc)
 	}
 
 	dwc->ep0_bounce = dma_alloc_coherent(dwc->dev,
-			512, &dwc->ep0_bounce_addr, GFP_KERNEL);
+			DWC3_EP0_BOUNCE_SIZE, &dwc->ep0_bounce_addr,
+			GFP_KERNEL);
 	if (!dwc->ep0_bounce) {
 		dev_err(dwc->dev, "failed to allocate ep0 bounce buffer\n");
 		ret = -ENOMEM;
@@ -2312,6 +2368,14 @@ int __devinit dwc3_gadget_init(struct dwc3 *dwc)
 		goto err5;
 	}
 
+	reg = dwc3_readl(dwc->regs, DWC3_DCFG);
+	reg |= DWC3_DCFG_LPM_CAP;
+	dwc3_writel(dwc->regs, DWC3_DCFG, reg);
+
+	reg = dwc3_readl(dwc->regs, DWC3_DCTL);
+	reg |= DWC3_DCTL_ACCEPTU1ENA | DWC3_DCTL_ACCEPTU2ENA;
+	dwc3_writel(dwc->regs, DWC3_DCTL, reg);
+
 	/* Enable all but Start and End of Frame IRQs */
 	reg = (DWC3_DEVTEN_VNDRDEVTSTRCVEDEN |
 			DWC3_DEVTEN_EVNTOVERFLOWEN |
@@ -2350,8 +2414,8 @@ err5:
 	dwc3_gadget_free_endpoints(dwc);
 
 err4:
-	dma_free_coherent(dwc->dev, 512, dwc->ep0_bounce,
-			dwc->ep0_bounce_addr);
+	dma_free_coherent(dwc->dev, DWC3_EP0_BOUNCE_SIZE,
+			dwc->ep0_bounce, dwc->ep0_bounce_addr);
 
 err3:
 	kfree(dwc->setup_buf);
@@ -2380,8 +2444,8 @@ void dwc3_gadget_exit(struct dwc3 *dwc)
 
 	dwc3_gadget_free_endpoints(dwc);
 
-	dma_free_coherent(dwc->dev, 512, dwc->ep0_bounce,
-			dwc->ep0_bounce_addr);
+	dma_free_coherent(dwc->dev, DWC3_EP0_BOUNCE_SIZE,
+			dwc->ep0_bounce, dwc->ep0_bounce_addr);
 
 	kfree(dwc->setup_buf);
 
diff --git a/drivers/usb/dwc3/gadget.h b/drivers/usb/dwc3/gadget.h
index a8600084348c..95ef6a2f7764 100644
--- a/drivers/usb/dwc3/gadget.h
+++ b/drivers/usb/dwc3/gadget.h
@@ -111,6 +111,7 @@ int dwc3_gadget_ep0_queue(struct usb_ep *ep, struct usb_request *request,
 int __dwc3_gadget_ep_set_halt(struct dwc3_ep *dep, int value);
 int dwc3_send_gadget_ep_cmd(struct dwc3 *dwc, unsigned ep,
 		unsigned cmd, struct dwc3_gadget_ep_cmd_params *params);
+int dwc3_send_gadget_generic_command(struct dwc3 *dwc, int cmd, u32 param);
 
 /**
  * dwc3_gadget_ep_get_transfer_index - Gets transfer index from HW
diff --git a/drivers/usb/dwc3/host.c b/drivers/usb/dwc3/host.c
index b108d18fd40d..56a62342884d 100644
--- a/drivers/usb/dwc3/host.c
+++ b/drivers/usb/dwc3/host.c
@@ -39,15 +39,6 @@
 
 #include "core.h"
 
-static struct resource generic_resources[] = {
-	{
-		.flags = IORESOURCE_IRQ,
-	},
-	{
-		.flags = IORESOURCE_MEM,
-	},
-};
-
 int dwc3_host_init(struct dwc3 *dwc)
 {
 	struct platform_device	*xhci;
@@ -68,14 +59,8 @@ int dwc3_host_init(struct dwc3 *dwc)
 
 	dwc->xhci = xhci;
 
-	/* setup resources */
-	generic_resources[0].start = dwc->irq;
-
-	generic_resources[1].start = dwc->res->start;
-	generic_resources[1].end = dwc->res->start + 0x7fff;
-
-	ret = platform_device_add_resources(xhci, generic_resources,
-			ARRAY_SIZE(generic_resources));
+	ret = platform_device_add_resources(xhci, dwc->xhci_resources,
+						DWC3_XHCI_RESOURCES_NUM);
 	if (ret) {
 		dev_err(dwc->dev, "couldn't add resources to xHCI device\n");
 		goto err1;
diff --git a/drivers/usb/dwc3/io.h b/drivers/usb/dwc3/io.h
index 071d561f3e68..a50f76b9d19b 100644
--- a/drivers/usb/dwc3/io.h
+++ b/drivers/usb/dwc3/io.h
@@ -41,14 +41,26 @@
 
 #include <linux/io.h>
 
+#include "core.h"
+
 static inline u32 dwc3_readl(void __iomem *base, u32 offset)
 {
-	return readl(base + offset);
+	/*
+	 * We requested the mem region starting from the Globals address
+	 * space, see dwc3_probe in core.c.
+	 * However, the offsets are given starting from xHCI address space.
+	 */
+	return readl(base + (offset - DWC3_GLOBALS_REGS_START));
 }
 
 static inline void dwc3_writel(void __iomem *base, u32 offset, u32 value)
 {
-	writel(value, base + offset);
+	/*
+	 * We requested the mem region starting from the Globals address
+	 * space, see dwc3_probe in core.c.
+	 * However, the offsets are given starting from xHCI address space.
+	 */
+	writel(value, base + (offset - DWC3_GLOBALS_REGS_START));
 }
 
 #endif /* __DRIVERS_USB_DWC3_IO_H */