spi: tegra114: change format for `spi_set_cs_timing()` function

The initial version of `spi_set_cs_timing()` was implemented with
consideration only for clock-cycles as delay.

For cases like `CS setup` time, it's sometimes needed that micro-seconds
(or nano-seconds) are required, or sometimes even longer delays, for cases
where the device needs a little longer to start transferring that after CS
is asserted.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20190926105147.7839-15-alexandru.ardelean@analog.com
Signed-off-by: Mark Brown <broonie@kernel.org>

2 files changed, 30 insertions, 8 deletions

diff --git a/drivers/spi/spi-tegra114.c b/drivers/spi/spi-tegra114.c
index 8133dc49d34f..e6a450d9b4f0 100644
--- a/drivers/spi/spi-tegra114.c
+++ b/drivers/spi/spi-tegra114.c
@@ -723,15 +723,31 @@ static void tegra_spi_deinit_dma_param(struct tegra_spi_data *tspi,
 	dma_release_channel(dma_chan);
 }
 
-static void tegra_spi_set_hw_cs_timing(struct spi_device *spi, u8 setup_dly,
-				       u8 hold_dly, u8 inactive_dly)
+static int tegra_spi_set_hw_cs_timing(struct spi_device *spi,
+				      struct spi_delay *setup,
+				      struct spi_delay *hold,
+				      struct spi_delay *inactive)
 {
 	struct tegra_spi_data *tspi = spi_master_get_devdata(spi->master);
+	u8 setup_dly, hold_dly, inactive_dly;
 	u32 setup_hold;
 	u32 spi_cs_timing;
 	u32 inactive_cycles;
 	u8 cs_state;
 
+	if ((setup && setup->unit != SPI_DELAY_UNIT_SCK) ||
+	    (hold && hold->unit != SPI_DELAY_UNIT_SCK) ||
+	    (inactive && inactive->unit != SPI_DELAY_UNIT_SCK)) {
+		dev_err(&spi->dev,
+			"Invalid delay unit %d, should be SPI_DELAY_UNIT_SCK\n",
+			SPI_DELAY_UNIT_SCK);
+		return -EINVAL;
+	}
+
+	setup_dly = setup ? setup->value : 0;
+	hold_dly = hold ? hold->value : 0;
+	inactive_dly = inactive ? inactive->value : 0;
+
 	setup_dly = min_t(u8, setup_dly, MAX_SETUP_HOLD_CYCLES);
 	hold_dly = min_t(u8, hold_dly, MAX_SETUP_HOLD_CYCLES);
 	if (setup_dly && hold_dly) {
@@ -758,6 +774,8 @@ static void tegra_spi_set_hw_cs_timing(struct spi_device *spi, u8 setup_dly,
 		tspi->spi_cs_timing2 = spi_cs_timing;
 		tegra_spi_writel(tspi, spi_cs_timing, SPI_CS_TIMING2);
 	}
+
+	return 0;
 }
 
 static u32 tegra_spi_setup_transfer_one(struct spi_device *spi,
diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 2e448078a117..6beeb363515c 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -3269,15 +3269,19 @@ EXPORT_SYMBOL_GPL(spi_setup);
 /**
  * spi_set_cs_timing - configure CS setup, hold, and inactive delays
  * @spi: the device that requires specific CS timing configuration
- * @setup: CS setup time in terms of clock count
- * @hold: CS hold time in terms of clock count
- * @inactive_dly: CS inactive delay between transfers in terms of clock count
+ * @setup: CS setup time specified via @spi_delay
+ * @hold: CS hold time specified via @spi_delay
+ * @inactive: CS inactive delay between transfers specified via @spi_delay
+ *
+ * Return: zero on success, else a negative error code.
  */
-void spi_set_cs_timing(struct spi_device *spi, u8 setup, u8 hold,
-		       u8 inactive_dly)
+int spi_set_cs_timing(struct spi_device *spi, struct spi_delay *setup,
+		      struct spi_delay *hold, struct spi_delay *inactive)
 {
 	if (spi->controller->set_cs_timing)
-		spi->controller->set_cs_timing(spi, setup, hold, inactive_dly);
+		return spi->controller->set_cs_timing(spi, setup, hold,
+						      inactive);
+	return -ENOTSUPP;
 }
 EXPORT_SYMBOL_GPL(spi_set_cs_timing);