Merge tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc

Pull more ARM multiplatform updates from Arnd Bergmann:
 "The second part of the multiplatform changes now converts the
  Intel/Marvell PXA platform along with the rest. The patches went
  through several rebases before the merge window as bugs were found, so
  they remained separate.

  This has to touch a lot of drivers, in particular the touchscreen,
  pcmcia, sound and clk bits, to detach the driver files from the
  platform and board specific header files"

* tag 'arm-multiplatform-5.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (48 commits)
  ARM: pxa/mmp: remove traces of plat-pxa
  ARM: pxa: convert to multiplatform
  ARM: pxa/sa1100: move I/O space to PCI_IOBASE
  ARM: pxa: remove support for MTD_XIP
  ARM: pxa: move mach/*.h to mach-pxa/
  ARM: PXA: fix multi-cpu build of xsc3
  ARM: pxa: move plat-pxa to drivers/soc/
  ARM: mmp: rename pxa_register_device
  ARM: mmp: remove tavorevb board support
  ARM: pxa: remove unused mach/bitfield.h
  ARM: pxa: move clk register definitions to driver
  ARM: pxa: move smemc register access from clk to platform
  cpufreq: pxa3: move clk register access to clk driver
  ARM: pxa: remove get_clk_frequency_khz()
  ARM: pxa: pcmcia: move smemc configuration back to arch
  ASoC: pxa: i2s: use normal MMIO accessors
  ASoC: pxa: ac97: use normal MMIO accessors
  ASoC: pxa: use pdev resource for FIFO regs
  Input: wm97xx - get rid of irq_enable method in wm97xx_mach_ops
  Input: wm97xx - switch to using threaded IRQ
  ...

6 files changed, 529 insertions, 0 deletions

diff --git a/drivers/soc/Kconfig b/drivers/soc/Kconfig
index c5aae42673d3..86ccf5970bc1 100644
--- a/drivers/soc/Kconfig
+++ b/drivers/soc/Kconfig
@@ -14,6 +14,7 @@ source "drivers/soc/ixp4xx/Kconfig"
 source "drivers/soc/litex/Kconfig"
 source "drivers/soc/mediatek/Kconfig"
 source "drivers/soc/microchip/Kconfig"
+source "drivers/soc/pxa/Kconfig"
 source "drivers/soc/qcom/Kconfig"
 source "drivers/soc/renesas/Kconfig"
 source "drivers/soc/rockchip/Kconfig"
diff --git a/drivers/soc/Makefile b/drivers/soc/Makefile
index e8228c4e5d18..919716e0e700 100644
--- a/drivers/soc/Makefile
+++ b/drivers/soc/Makefile
@@ -19,6 +19,7 @@ obj-$(CONFIG_SOC_XWAY)		+= lantiq/
 obj-$(CONFIG_LITEX_SOC_CONTROLLER) += litex/
 obj-y				+= mediatek/
 obj-y				+= microchip/
+obj-y				+= pxa/
 obj-y				+= amlogic/
 obj-y				+= qcom/
 obj-y				+= renesas/
diff --git a/drivers/soc/pxa/Kconfig b/drivers/soc/pxa/Kconfig
new file mode 100644
index 000000000000..c5c265aa4f07
--- /dev/null
+++ b/drivers/soc/pxa/Kconfig
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0-only
+config PLAT_PXA
+	bool
+
+config PXA_SSP
+	tristate
+	help
+	  Enable support for PXA2xx SSP ports
diff --git a/drivers/soc/pxa/Makefile b/drivers/soc/pxa/Makefile
new file mode 100644
index 000000000000..413deceddbdd
--- /dev/null
+++ b/drivers/soc/pxa/Makefile
@@ -0,0 +1,6 @@
+# SPDX-License-Identifier: GPL-2.0-only
+
+obj-$(CONFIG_PXA3xx)		+= mfp.o
+obj-$(CONFIG_ARCH_MMP)		+= mfp.o
+
+obj-$(CONFIG_PXA_SSP)		+= ssp.o
diff --git a/drivers/soc/pxa/mfp.c b/drivers/soc/pxa/mfp.c
new file mode 100644
index 000000000000..6220ba321cfc
--- /dev/null
+++ b/drivers/soc/pxa/mfp.c
@@ -0,0 +1,282 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * linux/arch/arm/plat-pxa/mfp.c
+ *
+ *   Multi-Function Pin Support
+ *
+ * Copyright (C) 2007 Marvell Internation Ltd.
+ *
+ * 2007-08-21: eric miao <eric.miao@marvell.com>
+ *             initial version
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/io.h>
+
+#include <linux/soc/pxa/mfp.h>
+
+#define MFPR_SIZE	(PAGE_SIZE)
+
+/* MFPR register bit definitions */
+#define MFPR_PULL_SEL		(0x1 << 15)
+#define MFPR_PULLUP_EN		(0x1 << 14)
+#define MFPR_PULLDOWN_EN	(0x1 << 13)
+#define MFPR_SLEEP_SEL		(0x1 << 9)
+#define MFPR_SLEEP_OE_N		(0x1 << 7)
+#define MFPR_EDGE_CLEAR		(0x1 << 6)
+#define MFPR_EDGE_FALL_EN	(0x1 << 5)
+#define MFPR_EDGE_RISE_EN	(0x1 << 4)
+
+#define MFPR_SLEEP_DATA(x)	((x) << 8)
+#define MFPR_DRIVE(x)		(((x) & 0x7) << 10)
+#define MFPR_AF_SEL(x)		(((x) & 0x7) << 0)
+
+#define MFPR_EDGE_NONE		(0)
+#define MFPR_EDGE_RISE		(MFPR_EDGE_RISE_EN)
+#define MFPR_EDGE_FALL		(MFPR_EDGE_FALL_EN)
+#define MFPR_EDGE_BOTH		(MFPR_EDGE_RISE | MFPR_EDGE_FALL)
+
+/*
+ * Table that determines the low power modes outputs, with actual settings
+ * used in parentheses for don't-care values. Except for the float output,
+ * the configured driven and pulled levels match, so if there is a need for
+ * non-LPM pulled output, the same configuration could probably be used.
+ *
+ * Output value  sleep_oe_n  sleep_data  pullup_en  pulldown_en  pull_sel
+ *                 (bit 7)    (bit 8)    (bit 14)     (bit 13)   (bit 15)
+ *
+ * Input            0          X(0)        X(0)        X(0)       0
+ * Drive 0          0          0           0           X(1)       0
+ * Drive 1          0          1           X(1)        0	  0
+ * Pull hi (1)      1          X(1)        1           0	  0
+ * Pull lo (0)      1          X(0)        0           1	  0
+ * Z (float)        1          X(0)        0           0	  0
+ */
+#define MFPR_LPM_INPUT		(0)
+#define MFPR_LPM_DRIVE_LOW	(MFPR_SLEEP_DATA(0) | MFPR_PULLDOWN_EN)
+#define MFPR_LPM_DRIVE_HIGH    	(MFPR_SLEEP_DATA(1) | MFPR_PULLUP_EN)
+#define MFPR_LPM_PULL_LOW      	(MFPR_LPM_DRIVE_LOW  | MFPR_SLEEP_OE_N)
+#define MFPR_LPM_PULL_HIGH     	(MFPR_LPM_DRIVE_HIGH | MFPR_SLEEP_OE_N)
+#define MFPR_LPM_FLOAT         	(MFPR_SLEEP_OE_N)
+#define MFPR_LPM_MASK		(0xe080)
+
+/*
+ * The pullup and pulldown state of the MFP pin at run mode is by default
+ * determined by the selected alternate function. In case that some buggy
+ * devices need to override this default behavior,  the definitions below
+ * indicates the setting of corresponding MFPR bits
+ *
+ * Definition       pull_sel  pullup_en  pulldown_en
+ * MFPR_PULL_NONE       0         0        0
+ * MFPR_PULL_LOW        1         0        1
+ * MFPR_PULL_HIGH       1         1        0
+ * MFPR_PULL_BOTH       1         1        1
+ * MFPR_PULL_FLOAT	1         0        0
+ */
+#define MFPR_PULL_NONE		(0)
+#define MFPR_PULL_LOW		(MFPR_PULL_SEL | MFPR_PULLDOWN_EN)
+#define MFPR_PULL_BOTH		(MFPR_PULL_LOW | MFPR_PULLUP_EN)
+#define MFPR_PULL_HIGH		(MFPR_PULL_SEL | MFPR_PULLUP_EN)
+#define MFPR_PULL_FLOAT		(MFPR_PULL_SEL)
+
+/* mfp_spin_lock is used to ensure that MFP register configuration
+ * (most likely a read-modify-write operation) is atomic, and that
+ * mfp_table[] is consistent
+ */
+static DEFINE_SPINLOCK(mfp_spin_lock);
+
+static void __iomem *mfpr_mmio_base;
+
+struct mfp_pin {
+	unsigned long	config;		/* -1 for not configured */
+	unsigned long	mfpr_off;	/* MFPRxx Register offset */
+	unsigned long	mfpr_run;	/* Run-Mode Register Value */
+	unsigned long	mfpr_lpm;	/* Low Power Mode Register Value */
+};
+
+static struct mfp_pin mfp_table[MFP_PIN_MAX];
+
+/* mapping of MFP_LPM_* definitions to MFPR_LPM_* register bits */
+static const unsigned long mfpr_lpm[] = {
+	MFPR_LPM_INPUT,
+	MFPR_LPM_DRIVE_LOW,
+	MFPR_LPM_DRIVE_HIGH,
+	MFPR_LPM_PULL_LOW,
+	MFPR_LPM_PULL_HIGH,
+	MFPR_LPM_FLOAT,
+	MFPR_LPM_INPUT,
+};
+
+/* mapping of MFP_PULL_* definitions to MFPR_PULL_* register bits */
+static const unsigned long mfpr_pull[] = {
+	MFPR_PULL_NONE,
+	MFPR_PULL_LOW,
+	MFPR_PULL_HIGH,
+	MFPR_PULL_BOTH,
+	MFPR_PULL_FLOAT,
+};
+
+/* mapping of MFP_LPM_EDGE_* definitions to MFPR_EDGE_* register bits */
+static const unsigned long mfpr_edge[] = {
+	MFPR_EDGE_NONE,
+	MFPR_EDGE_RISE,
+	MFPR_EDGE_FALL,
+	MFPR_EDGE_BOTH,
+};
+
+#define mfpr_readl(off)			\
+	__raw_readl(mfpr_mmio_base + (off))
+
+#define mfpr_writel(off, val)		\
+	__raw_writel(val, mfpr_mmio_base + (off))
+
+#define mfp_configured(p)	((p)->config != -1)
+
+/*
+ * perform a read-back of any valid MFPR register to make sure the
+ * previous writings are finished
+ */
+static unsigned long mfpr_off_readback;
+#define mfpr_sync()	(void)__raw_readl(mfpr_mmio_base + mfpr_off_readback)
+
+static inline void __mfp_config_run(struct mfp_pin *p)
+{
+	if (mfp_configured(p))
+		mfpr_writel(p->mfpr_off, p->mfpr_run);
+}
+
+static inline void __mfp_config_lpm(struct mfp_pin *p)
+{
+	if (mfp_configured(p)) {
+		unsigned long mfpr_clr = (p->mfpr_run & ~MFPR_EDGE_BOTH) | MFPR_EDGE_CLEAR;
+		if (mfpr_clr != p->mfpr_run)
+			mfpr_writel(p->mfpr_off, mfpr_clr);
+		if (p->mfpr_lpm != mfpr_clr)
+			mfpr_writel(p->mfpr_off, p->mfpr_lpm);
+	}
+}
+
+void mfp_config(unsigned long *mfp_cfgs, int num)
+{
+	unsigned long flags;
+	int i;
+
+	spin_lock_irqsave(&mfp_spin_lock, flags);
+
+	for (i = 0; i < num; i++, mfp_cfgs++) {
+		unsigned long tmp, c = *mfp_cfgs;
+		struct mfp_pin *p;
+		int pin, af, drv, lpm, edge, pull;
+
+		pin = MFP_PIN(c);
+		BUG_ON(pin >= MFP_PIN_MAX);
+		p = &mfp_table[pin];
+
+		af  = MFP_AF(c);
+		drv = MFP_DS(c);
+		lpm = MFP_LPM_STATE(c);
+		edge = MFP_LPM_EDGE(c);
+		pull = MFP_PULL(c);
+
+		/* run-mode pull settings will conflict with MFPR bits of
+		 * low power mode state,  calculate mfpr_run and mfpr_lpm
+		 * individually if pull != MFP_PULL_NONE
+		 */
+		tmp = MFPR_AF_SEL(af) | MFPR_DRIVE(drv);
+
+		if (likely(pull == MFP_PULL_NONE)) {
+			p->mfpr_run = tmp | mfpr_lpm[lpm] | mfpr_edge[edge];
+			p->mfpr_lpm = p->mfpr_run;
+		} else {
+			p->mfpr_lpm = tmp | mfpr_lpm[lpm] | mfpr_edge[edge];
+			p->mfpr_run = tmp | mfpr_pull[pull];
+		}
+
+		p->config = c; __mfp_config_run(p);
+	}
+
+	mfpr_sync();
+	spin_unlock_irqrestore(&mfp_spin_lock, flags);
+}
+
+unsigned long mfp_read(int mfp)
+{
+	unsigned long val, flags;
+
+	BUG_ON(mfp < 0 || mfp >= MFP_PIN_MAX);
+
+	spin_lock_irqsave(&mfp_spin_lock, flags);
+	val = mfpr_readl(mfp_table[mfp].mfpr_off);
+	spin_unlock_irqrestore(&mfp_spin_lock, flags);
+
+	return val;
+}
+
+void mfp_write(int mfp, unsigned long val)
+{
+	unsigned long flags;
+
+	BUG_ON(mfp < 0 || mfp >= MFP_PIN_MAX);
+
+	spin_lock_irqsave(&mfp_spin_lock, flags);
+	mfpr_writel(mfp_table[mfp].mfpr_off, val);
+	mfpr_sync();
+	spin_unlock_irqrestore(&mfp_spin_lock, flags);
+}
+
+void __init mfp_init_base(void __iomem *mfpr_base)
+{
+	int i;
+
+	/* initialize the table with default - unconfigured */
+	for (i = 0; i < ARRAY_SIZE(mfp_table); i++)
+		mfp_table[i].config = -1;
+
+	mfpr_mmio_base = mfpr_base;
+}
+
+void __init mfp_init_addr(struct mfp_addr_map *map)
+{
+	struct mfp_addr_map *p;
+	unsigned long offset, flags;
+	int i;
+
+	spin_lock_irqsave(&mfp_spin_lock, flags);
+
+	/* mfp offset for readback */
+	mfpr_off_readback = map[0].offset;
+
+	for (p = map; p->start != MFP_PIN_INVALID; p++) {
+		offset = p->offset;
+		i = p->start;
+
+		do {
+			mfp_table[i].mfpr_off = offset;
+			mfp_table[i].mfpr_run = 0;
+			mfp_table[i].mfpr_lpm = 0;
+			offset += 4; i++;
+		} while ((i <= p->end) && (p->end != -1));
+	}
+
+	spin_unlock_irqrestore(&mfp_spin_lock, flags);
+}
+
+void mfp_config_lpm(void)
+{
+	struct mfp_pin *p = &mfp_table[0];
+	int pin;
+
+	for (pin = 0; pin < ARRAY_SIZE(mfp_table); pin++, p++)
+		__mfp_config_lpm(p);
+}
+
+void mfp_config_run(void)
+{
+	struct mfp_pin *p = &mfp_table[0];
+	int pin;
+
+	for (pin = 0; pin < ARRAY_SIZE(mfp_table); pin++, p++)
+		__mfp_config_run(p);
+}
diff --git a/drivers/soc/pxa/ssp.c b/drivers/soc/pxa/ssp.c
new file mode 100644
index 000000000000..563440315acd
--- /dev/null
+++ b/drivers/soc/pxa/ssp.c
@@ -0,0 +1,231 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ *  linux/arch/arm/mach-pxa/ssp.c
+ *
+ *  based on linux/arch/arm/mach-sa1100/ssp.c by Russell King
+ *
+ *  Copyright (C) 2003 Russell King.
+ *  Copyright (C) 2003 Wolfson Microelectronics PLC
+ *
+ *  PXA2xx SSP driver.  This provides the generic core for simple
+ *  IO-based SSP applications and allows easy port setup for DMA access.
+ *
+ *  Author: Liam Girdwood <liam.girdwood@wolfsonmicro.com>
+ */
+
+#include <linux/module.h>
+#include <linux/kernel.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/mutex.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/platform_device.h>
+#include <linux/spi/pxa2xx_spi.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+
+#include <asm/irq.h>
+
+static DEFINE_MUTEX(ssp_lock);
+static LIST_HEAD(ssp_list);
+
+struct ssp_device *pxa_ssp_request(int port, const char *label)
+{
+	struct ssp_device *ssp = NULL;
+
+	mutex_lock(&ssp_lock);
+
+	list_for_each_entry(ssp, &ssp_list, node) {
+		if (ssp->port_id == port && ssp->use_count == 0) {
+			ssp->use_count++;
+			ssp->label = label;
+			break;
+		}
+	}
+
+	mutex_unlock(&ssp_lock);
+
+	if (&ssp->node == &ssp_list)
+		return NULL;
+
+	return ssp;
+}
+EXPORT_SYMBOL(pxa_ssp_request);
+
+struct ssp_device *pxa_ssp_request_of(const struct device_node *of_node,
+				      const char *label)
+{
+	struct ssp_device *ssp = NULL;
+
+	mutex_lock(&ssp_lock);
+
+	list_for_each_entry(ssp, &ssp_list, node) {
+		if (ssp->of_node == of_node && ssp->use_count == 0) {
+			ssp->use_count++;
+			ssp->label = label;
+			break;
+		}
+	}
+
+	mutex_unlock(&ssp_lock);
+
+	if (&ssp->node == &ssp_list)
+		return NULL;
+
+	return ssp;
+}
+EXPORT_SYMBOL(pxa_ssp_request_of);
+
+void pxa_ssp_free(struct ssp_device *ssp)
+{
+	mutex_lock(&ssp_lock);
+	if (ssp->use_count) {
+		ssp->use_count--;
+		ssp->label = NULL;
+	} else
+		dev_err(ssp->dev, "device already free\n");
+	mutex_unlock(&ssp_lock);
+}
+EXPORT_SYMBOL(pxa_ssp_free);
+
+#ifdef CONFIG_OF
+static const struct of_device_id pxa_ssp_of_ids[] = {
+	{ .compatible = "mrvl,pxa25x-ssp",	.data = (void *) PXA25x_SSP },
+	{ .compatible = "mvrl,pxa25x-nssp",	.data = (void *) PXA25x_NSSP },
+	{ .compatible = "mrvl,pxa27x-ssp",	.data = (void *) PXA27x_SSP },
+	{ .compatible = "mrvl,pxa3xx-ssp",	.data = (void *) PXA3xx_SSP },
+	{ .compatible = "mvrl,pxa168-ssp",	.data = (void *) PXA168_SSP },
+	{ .compatible = "mrvl,pxa910-ssp",	.data = (void *) PXA910_SSP },
+	{ .compatible = "mrvl,ce4100-ssp",	.data = (void *) CE4100_SSP },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, pxa_ssp_of_ids);
+#endif
+
+static int pxa_ssp_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct ssp_device *ssp;
+	struct device *dev = &pdev->dev;
+
+	ssp = devm_kzalloc(dev, sizeof(struct ssp_device), GFP_KERNEL);
+	if (ssp == NULL)
+		return -ENOMEM;
+
+	ssp->dev = dev;
+
+	ssp->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(ssp->clk))
+		return PTR_ERR(ssp->clk);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (res == NULL) {
+		dev_err(dev, "no memory resource defined\n");
+		return -ENODEV;
+	}
+
+	res = devm_request_mem_region(dev, res->start, resource_size(res),
+				      pdev->name);
+	if (res == NULL) {
+		dev_err(dev, "failed to request memory resource\n");
+		return -EBUSY;
+	}
+
+	ssp->phys_base = res->start;
+
+	ssp->mmio_base = devm_ioremap(dev, res->start, resource_size(res));
+	if (ssp->mmio_base == NULL) {
+		dev_err(dev, "failed to ioremap() registers\n");
+		return -ENODEV;
+	}
+
+	ssp->irq = platform_get_irq(pdev, 0);
+	if (ssp->irq < 0) {
+		dev_err(dev, "no IRQ resource defined\n");
+		return -ENODEV;
+	}
+
+	if (dev->of_node) {
+		const struct of_device_id *id =
+			of_match_device(of_match_ptr(pxa_ssp_of_ids), dev);
+		ssp->type = (int) id->data;
+	} else {
+		const struct platform_device_id *id =
+			platform_get_device_id(pdev);
+		ssp->type = (int) id->driver_data;
+
+		/* PXA2xx/3xx SSP ports starts from 1 and the internal pdev->id
+		 * starts from 0, do a translation here
+		 */
+		ssp->port_id = pdev->id + 1;
+	}
+
+	ssp->use_count = 0;
+	ssp->of_node = dev->of_node;
+
+	mutex_lock(&ssp_lock);
+	list_add(&ssp->node, &ssp_list);
+	mutex_unlock(&ssp_lock);
+
+	platform_set_drvdata(pdev, ssp);
+
+	return 0;
+}
+
+static int pxa_ssp_remove(struct platform_device *pdev)
+{
+	struct ssp_device *ssp;
+
+	ssp = platform_get_drvdata(pdev);
+	if (ssp == NULL)
+		return -ENODEV;
+
+	mutex_lock(&ssp_lock);
+	list_del(&ssp->node);
+	mutex_unlock(&ssp_lock);
+
+	return 0;
+}
+
+static const struct platform_device_id ssp_id_table[] = {
+	{ "pxa25x-ssp",		PXA25x_SSP },
+	{ "pxa25x-nssp",	PXA25x_NSSP },
+	{ "pxa27x-ssp",		PXA27x_SSP },
+	{ "pxa3xx-ssp",		PXA3xx_SSP },
+	{ "pxa168-ssp",		PXA168_SSP },
+	{ "pxa910-ssp",		PXA910_SSP },
+	{ },
+};
+
+static struct platform_driver pxa_ssp_driver = {
+	.probe		= pxa_ssp_probe,
+	.remove		= pxa_ssp_remove,
+	.driver		= {
+		.name		= "pxa2xx-ssp",
+		.of_match_table	= of_match_ptr(pxa_ssp_of_ids),
+	},
+	.id_table	= ssp_id_table,
+};
+
+static int __init pxa_ssp_init(void)
+{
+	return platform_driver_register(&pxa_ssp_driver);
+}
+
+static void __exit pxa_ssp_exit(void)
+{
+	platform_driver_unregister(&pxa_ssp_driver);
+}
+
+arch_initcall(pxa_ssp_init);
+module_exit(pxa_ssp_exit);
+
+MODULE_DESCRIPTION("PXA SSP driver");
+MODULE_AUTHOR("Liam Girdwood");
+MODULE_LICENSE("GPL");