Merge tag 'phy-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-next

Kishon writes:

phy: for 5.1

  *) Add a new driver to support Armada 3700 COMPHY IP (supports SATA, USB3,
     PCIe)
  *) Add a new driver to support Armada UTMI PHY
  *) Add a new driver to support Cadence D-PHY
  *) Extend omap-usb2 PHY driver to be used for AM654 USB2 PHY
  *) Extend qcom-qmp PHY driver to be used for UFS PHY and USB3 PHY in Qualcomm
     MSM8998
  *) Extend qcom-qusb2 PHY driver to support QUSB2 PHY in Qualcomm MSM8998
  *) Remove module specific code that is present for drivers that can be only
     built-in
  *) Allow Freescale IMX8MQ USB to be used for multiple SoCs and not just
     i.MX8MQ
  *) Cleanups such as switch to SPDX identifier, use readl_poll_timeout macro,
     remove unused headers etc.,

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>

* tag 'phy-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy: (32 commits)
  phy: qcom-qmp: Add QMP UFS PHY support for msm8998
  dt-bindings: phy-qcom-qmp: Add qcom,msm8998-qmp-ufs-phy
  phy: bcm-sr-pcie: Change operation when PIPEMUX=1
  phy: Add Cadence D-PHY support
  dt-bindings: phy: Move the Cadence D-PHY bindings
  phy: dphy: Clarify lanes parameter documentation
  phy: dphy: Change units of wakeup and init parameters
  phy: dphy: Remove unused header
  MAINTAINERS: phy: fill Armada 3700 PHY drivers entry
  dt-bindings: phy: mvebu-utmi: add UTMI PHY bindings
  phy: add A3700 UTMI PHY driver
  MAINTAINERS: phy: add entry for Armada 3700 COMPHY driver
  dt-bindings: phy: mvebu-comphy: extend the file to describe a3700 bindings
  phy: add A3700 COMPHY support
  phy: mvebu-cp110-comphy: fix port check in ->xlate()
  phy: armada375-usb2: switch to SPDX license identifier
  phy: make phy-armada375-usb2 explicitly non-modular
  phy: make phy-mvebu-sata explicitly non-modular
  phy: make phy-core explicitly non-modular
  phy: qcom-qusb2: Add QUSB2 PHY support for msm8998
  ...

21 files changed, 1309 insertions, 130 deletions

diff --git a/drivers/phy/broadcom/phy-bcm-sr-pcie.c b/drivers/phy/broadcom/phy-bcm-sr-pcie.c
index c10e95f86de5..96a3af126a78 100644
--- a/drivers/phy/broadcom/phy-bcm-sr-pcie.c
+++ b/drivers/phy/broadcom/phy-bcm-sr-pcie.c
@@ -78,8 +78,8 @@ struct sr_pcie_phy_core {
 static const u8 pipemux_table[] = {
 	/* PIPEMUX = 0, EP 1x16 */
 	0x00,
-	/* PIPEMUX = 1, EP 2x8 */
-	0x00,
+	/* PIPEMUX = 1, EP 1x8 + RC 1x8, core 7 */
+	0x80,
 	/* PIPEMUX = 2, EP 4x4 */
 	0x00,
 	/* PIPEMUX = 3, RC 2x8, cores 0, 7 */
diff --git a/drivers/phy/cadence/Kconfig b/drivers/phy/cadence/Kconfig
index 2b8c0851ff33..31f18b67dd7c 100644
--- a/drivers/phy/cadence/Kconfig
+++ b/drivers/phy/cadence/Kconfig
@@ -1,6 +1,7 @@
 #
 # Phy drivers for Cadence PHYs
 #
+
 config PHY_CADENCE_DP
 	tristate "Cadence MHDP DisplayPort PHY driver"
 	depends on OF
@@ -9,9 +10,19 @@ config PHY_CADENCE_DP
 	help
 	  Support for Cadence MHDP DisplayPort PHY.
 
+config PHY_CADENCE_DPHY
+	tristate "Cadence D-PHY Support"
+	depends on HAS_IOMEM && OF
+	select GENERIC_PHY
+	select GENERIC_PHY_MIPI_DPHY
+	help
+	  Choose this option if you have a Cadence D-PHY in your
+	  system. If M is selected, the module will be called
+	  cdns-dphy.
+
 config PHY_CADENCE_SIERRA
 	tristate "Cadence Sierra PHY Driver"
 	depends on OF && HAS_IOMEM && RESET_CONTROLLER
 	select GENERIC_PHY
 	help
-	  Enable this to support the Cadence Sierra PHY driver
\ No newline at end of file
+	  Enable this to support the Cadence Sierra PHY driver
diff --git a/drivers/phy/cadence/Makefile b/drivers/phy/cadence/Makefile
index 412349af0492..2f9e3457b954 100644
--- a/drivers/phy/cadence/Makefile
+++ b/drivers/phy/cadence/Makefile
@@ -1,2 +1,3 @@
 obj-$(CONFIG_PHY_CADENCE_DP)	+= phy-cadence-dp.o
+obj-$(CONFIG_PHY_CADENCE_DPHY)	+= cdns-dphy.o
 obj-$(CONFIG_PHY_CADENCE_SIERRA)	+= phy-cadence-sierra.o
diff --git a/drivers/phy/cadence/cdns-dphy.c b/drivers/phy/cadence/cdns-dphy.c
new file mode 100644
index 000000000000..90c4e9b5aac8
--- /dev/null
+++ b/drivers/phy/cadence/cdns-dphy.c
@@ -0,0 +1,391 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright: 2017-2018 Cadence Design Systems, Inc.
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/reset.h>
+
+#include <linux/phy/phy.h>
+#include <linux/phy/phy-mipi-dphy.h>
+
+#define REG_WAKEUP_TIME_NS		800
+#define DPHY_PLL_RATE_HZ		108000000
+
+/* DPHY registers */
+#define DPHY_PMA_CMN(reg)		(reg)
+#define DPHY_PMA_LCLK(reg)		(0x100 + (reg))
+#define DPHY_PMA_LDATA(lane, reg)	(0x200 + ((lane) * 0x100) + (reg))
+#define DPHY_PMA_RCLK(reg)		(0x600 + (reg))
+#define DPHY_PMA_RDATA(lane, reg)	(0x700 + ((lane) * 0x100) + (reg))
+#define DPHY_PCS(reg)			(0xb00 + (reg))
+
+#define DPHY_CMN_SSM			DPHY_PMA_CMN(0x20)
+#define DPHY_CMN_SSM_EN			BIT(0)
+#define DPHY_CMN_TX_MODE_EN		BIT(9)
+
+#define DPHY_CMN_PWM			DPHY_PMA_CMN(0x40)
+#define DPHY_CMN_PWM_DIV(x)		((x) << 20)
+#define DPHY_CMN_PWM_LOW(x)		((x) << 10)
+#define DPHY_CMN_PWM_HIGH(x)		(x)
+
+#define DPHY_CMN_FBDIV			DPHY_PMA_CMN(0x4c)
+#define DPHY_CMN_FBDIV_VAL(low, high)	(((high) << 11) | ((low) << 22))
+#define DPHY_CMN_FBDIV_FROM_REG		(BIT(10) | BIT(21))
+
+#define DPHY_CMN_OPIPDIV		DPHY_PMA_CMN(0x50)
+#define DPHY_CMN_IPDIV_FROM_REG		BIT(0)
+#define DPHY_CMN_IPDIV(x)		((x) << 1)
+#define DPHY_CMN_OPDIV_FROM_REG		BIT(6)
+#define DPHY_CMN_OPDIV(x)		((x) << 7)
+
+#define DPHY_PSM_CFG			DPHY_PCS(0x4)
+#define DPHY_PSM_CFG_FROM_REG		BIT(0)
+#define DPHY_PSM_CLK_DIV(x)		((x) << 1)
+
+#define DSI_HBP_FRAME_OVERHEAD		12
+#define DSI_HSA_FRAME_OVERHEAD		14
+#define DSI_HFP_FRAME_OVERHEAD		6
+#define DSI_HSS_VSS_VSE_FRAME_OVERHEAD	4
+#define DSI_BLANKING_FRAME_OVERHEAD	6
+#define DSI_NULL_FRAME_OVERHEAD		6
+#define DSI_EOT_PKT_SIZE		4
+
+struct cdns_dphy_cfg {
+	u8 pll_ipdiv;
+	u8 pll_opdiv;
+	u16 pll_fbdiv;
+	unsigned int nlanes;
+};
+
+enum cdns_dphy_clk_lane_cfg {
+	DPHY_CLK_CFG_LEFT_DRIVES_ALL = 0,
+	DPHY_CLK_CFG_LEFT_DRIVES_RIGHT = 1,
+	DPHY_CLK_CFG_LEFT_DRIVES_LEFT = 2,
+	DPHY_CLK_CFG_RIGHT_DRIVES_ALL = 3,
+};
+
+struct cdns_dphy;
+struct cdns_dphy_ops {
+	int (*probe)(struct cdns_dphy *dphy);
+	void (*remove)(struct cdns_dphy *dphy);
+	void (*set_psm_div)(struct cdns_dphy *dphy, u8 div);
+	void (*set_clk_lane_cfg)(struct cdns_dphy *dphy,
+				 enum cdns_dphy_clk_lane_cfg cfg);
+	void (*set_pll_cfg)(struct cdns_dphy *dphy,
+			    const struct cdns_dphy_cfg *cfg);
+	unsigned long (*get_wakeup_time_ns)(struct cdns_dphy *dphy);
+};
+
+struct cdns_dphy {
+	struct cdns_dphy_cfg cfg;
+	void __iomem *regs;
+	struct clk *psm_clk;
+	struct clk *pll_ref_clk;
+	const struct cdns_dphy_ops *ops;
+	struct phy *phy;
+};
+
+static int cdns_dsi_get_dphy_pll_cfg(struct cdns_dphy *dphy,
+				     struct cdns_dphy_cfg *cfg,
+				     struct phy_configure_opts_mipi_dphy *opts,
+				     unsigned int *dsi_hfp_ext)
+{
+	unsigned long pll_ref_hz = clk_get_rate(dphy->pll_ref_clk);
+	u64 dlane_bps;
+
+	memset(cfg, 0, sizeof(*cfg));
+
+	if (pll_ref_hz < 9600000 || pll_ref_hz >= 150000000)
+		return -EINVAL;
+	else if (pll_ref_hz < 19200000)
+		cfg->pll_ipdiv = 1;
+	else if (pll_ref_hz < 38400000)
+		cfg->pll_ipdiv = 2;
+	else if (pll_ref_hz < 76800000)
+		cfg->pll_ipdiv = 4;
+	else
+		cfg->pll_ipdiv = 8;
+
+	dlane_bps = opts->hs_clk_rate;
+
+	if (dlane_bps > 2500000000UL || dlane_bps < 160000000UL)
+		return -EINVAL;
+	else if (dlane_bps >= 1250000000)
+		cfg->pll_opdiv = 1;
+	else if (dlane_bps >= 630000000)
+		cfg->pll_opdiv = 2;
+	else if (dlane_bps >= 320000000)
+		cfg->pll_opdiv = 4;
+	else if (dlane_bps >= 160000000)
+		cfg->pll_opdiv = 8;
+
+	cfg->pll_fbdiv = DIV_ROUND_UP_ULL(dlane_bps * 2 * cfg->pll_opdiv *
+					  cfg->pll_ipdiv,
+					  pll_ref_hz);
+
+	return 0;
+}
+
+static int cdns_dphy_setup_psm(struct cdns_dphy *dphy)
+{
+	unsigned long psm_clk_hz = clk_get_rate(dphy->psm_clk);
+	unsigned long psm_div;
+
+	if (!psm_clk_hz || psm_clk_hz > 100000000)
+		return -EINVAL;
+
+	psm_div = DIV_ROUND_CLOSEST(psm_clk_hz, 1000000);
+	if (dphy->ops->set_psm_div)
+		dphy->ops->set_psm_div(dphy, psm_div);
+
+	return 0;
+}
+
+static void cdns_dphy_set_clk_lane_cfg(struct cdns_dphy *dphy,
+				       enum cdns_dphy_clk_lane_cfg cfg)
+{
+	if (dphy->ops->set_clk_lane_cfg)
+		dphy->ops->set_clk_lane_cfg(dphy, cfg);
+}
+
+static void cdns_dphy_set_pll_cfg(struct cdns_dphy *dphy,
+				  const struct cdns_dphy_cfg *cfg)
+{
+	if (dphy->ops->set_pll_cfg)
+		dphy->ops->set_pll_cfg(dphy, cfg);
+}
+
+static unsigned long cdns_dphy_get_wakeup_time_ns(struct cdns_dphy *dphy)
+{
+	return dphy->ops->get_wakeup_time_ns(dphy);
+}
+
+static unsigned long cdns_dphy_ref_get_wakeup_time_ns(struct cdns_dphy *dphy)
+{
+	/* Default wakeup time is 800 ns (in a simulated environment). */
+	return 800;
+}
+
+static void cdns_dphy_ref_set_pll_cfg(struct cdns_dphy *dphy,
+				      const struct cdns_dphy_cfg *cfg)
+{
+	u32 fbdiv_low, fbdiv_high;
+
+	fbdiv_low = (cfg->pll_fbdiv / 4) - 2;
+	fbdiv_high = cfg->pll_fbdiv - fbdiv_low - 2;
+
+	writel(DPHY_CMN_IPDIV_FROM_REG | DPHY_CMN_OPDIV_FROM_REG |
+	       DPHY_CMN_IPDIV(cfg->pll_ipdiv) |
+	       DPHY_CMN_OPDIV(cfg->pll_opdiv),
+	       dphy->regs + DPHY_CMN_OPIPDIV);
+	writel(DPHY_CMN_FBDIV_FROM_REG |
+	       DPHY_CMN_FBDIV_VAL(fbdiv_low, fbdiv_high),
+	       dphy->regs + DPHY_CMN_FBDIV);
+	writel(DPHY_CMN_PWM_HIGH(6) | DPHY_CMN_PWM_LOW(0x101) |
+	       DPHY_CMN_PWM_DIV(0x8),
+	       dphy->regs + DPHY_CMN_PWM);
+}
+
+static void cdns_dphy_ref_set_psm_div(struct cdns_dphy *dphy, u8 div)
+{
+	writel(DPHY_PSM_CFG_FROM_REG | DPHY_PSM_CLK_DIV(div),
+	       dphy->regs + DPHY_PSM_CFG);
+}
+
+/*
+ * This is the reference implementation of DPHY hooks. Specific integration of
+ * this IP may have to re-implement some of them depending on how they decided
+ * to wire things in the SoC.
+ */
+static const struct cdns_dphy_ops ref_dphy_ops = {
+	.get_wakeup_time_ns = cdns_dphy_ref_get_wakeup_time_ns,
+	.set_pll_cfg = cdns_dphy_ref_set_pll_cfg,
+	.set_psm_div = cdns_dphy_ref_set_psm_div,
+};
+
+static int cdns_dphy_config_from_opts(struct phy *phy,
+				      struct phy_configure_opts_mipi_dphy *opts,
+				      struct cdns_dphy_cfg *cfg)
+{
+	struct cdns_dphy *dphy = phy_get_drvdata(phy);
+	unsigned int dsi_hfp_ext = 0;
+	int ret;
+
+	ret = phy_mipi_dphy_config_validate(opts);
+	if (ret)
+		return ret;
+
+	ret = cdns_dsi_get_dphy_pll_cfg(dphy, cfg,
+					opts, &dsi_hfp_ext);
+	if (ret)
+		return ret;
+
+	opts->wakeup = cdns_dphy_get_wakeup_time_ns(dphy) / 1000;
+
+	return 0;
+}
+
+static int cdns_dphy_validate(struct phy *phy, enum phy_mode mode, int submode,
+			      union phy_configure_opts *opts)
+{
+	struct cdns_dphy_cfg cfg = { 0 };
+
+	if (mode != PHY_MODE_MIPI_DPHY)
+		return -EINVAL;
+
+	return cdns_dphy_config_from_opts(phy, &opts->mipi_dphy, &cfg);
+}
+
+static int cdns_dphy_configure(struct phy *phy, union phy_configure_opts *opts)
+{
+	struct cdns_dphy *dphy = phy_get_drvdata(phy);
+	struct cdns_dphy_cfg cfg = { 0 };
+	int ret;
+
+	ret = cdns_dphy_config_from_opts(phy, &opts->mipi_dphy, &cfg);
+	if (ret)
+		return ret;
+
+	/*
+	 * Configure the internal PSM clk divider so that the DPHY has a
+	 * 1MHz clk (or something close).
+	 */
+	ret = cdns_dphy_setup_psm(dphy);
+	if (ret)
+		return ret;
+
+	/*
+	 * Configure attach clk lanes to data lanes: the DPHY has 2 clk lanes
+	 * and 8 data lanes, each clk lane can be attache different set of
+	 * data lanes. The 2 groups are named 'left' and 'right', so here we
+	 * just say that we want the 'left' clk lane to drive the 'left' data
+	 * lanes.
+	 */
+	cdns_dphy_set_clk_lane_cfg(dphy, DPHY_CLK_CFG_LEFT_DRIVES_LEFT);
+
+	/*
+	 * Configure the DPHY PLL that will be used to generate the TX byte
+	 * clk.
+	 */
+	cdns_dphy_set_pll_cfg(dphy, &cfg);
+
+	return 0;
+}
+
+static int cdns_dphy_power_on(struct phy *phy)
+{
+	struct cdns_dphy *dphy = phy_get_drvdata(phy);
+
+	clk_prepare_enable(dphy->psm_clk);
+	clk_prepare_enable(dphy->pll_ref_clk);
+
+	/* Start TX state machine. */
+	writel(DPHY_CMN_SSM_EN | DPHY_CMN_TX_MODE_EN,
+	       dphy->regs + DPHY_CMN_SSM);
+
+	return 0;
+}
+
+static int cdns_dphy_power_off(struct phy *phy)
+{
+	struct cdns_dphy *dphy = phy_get_drvdata(phy);
+
+	clk_disable_unprepare(dphy->pll_ref_clk);
+	clk_disable_unprepare(dphy->psm_clk);
+
+	return 0;
+}
+
+static const struct phy_ops cdns_dphy_ops = {
+	.configure	= cdns_dphy_configure,
+	.validate	= cdns_dphy_validate,
+	.power_on	= cdns_dphy_power_on,
+	.power_off	= cdns_dphy_power_off,
+};
+
+static int cdns_dphy_probe(struct platform_device *pdev)
+{
+	struct phy_provider *phy_provider;
+	struct cdns_dphy *dphy;
+	struct resource *res;
+	int ret;
+
+	dphy = devm_kzalloc(&pdev->dev, sizeof(*dphy), GFP_KERNEL);
+	if (!dphy)
+		return -ENOMEM;
+	dev_set_drvdata(&pdev->dev, dphy);
+
+	dphy->ops = of_device_get_match_data(&pdev->dev);
+	if (!dphy->ops)
+		return -EINVAL;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	dphy->regs = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(dphy->regs))
+		return PTR_ERR(dphy->regs);
+
+	dphy->psm_clk = devm_clk_get(&pdev->dev, "psm");
+	if (IS_ERR(dphy->psm_clk))
+		return PTR_ERR(dphy->psm_clk);
+
+	dphy->pll_ref_clk = devm_clk_get(&pdev->dev, "pll_ref");
+	if (IS_ERR(dphy->pll_ref_clk))
+		return PTR_ERR(dphy->pll_ref_clk);
+
+	if (dphy->ops->probe) {
+		ret = dphy->ops->probe(dphy);
+		if (ret)
+			return ret;
+	}
+
+	dphy->phy = devm_phy_create(&pdev->dev, NULL, &cdns_dphy_ops);
+	if (IS_ERR(dphy->phy)) {
+		dev_err(&pdev->dev, "failed to create PHY\n");
+		if (dphy->ops->remove)
+			dphy->ops->remove(dphy);
+		return PTR_ERR(dphy->phy);
+	}
+
+	phy_set_drvdata(dphy->phy, dphy);
+	phy_provider = devm_of_phy_provider_register(&pdev->dev,
+						     of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(phy_provider);
+}
+
+static int cdns_dphy_remove(struct platform_device *pdev)
+{
+	struct cdns_dphy *dphy = dev_get_drvdata(&pdev->dev);
+
+	if (dphy->ops->remove)
+		dphy->ops->remove(dphy);
+
+	return 0;
+}
+
+static const struct of_device_id cdns_dphy_of_match[] = {
+	{ .compatible = "cdns,dphy", .data = &ref_dphy_ops },
+	{ /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, cdns_dphy_of_match);
+
+static struct platform_driver cdns_dphy_platform_driver = {
+	.probe		= cdns_dphy_probe,
+	.remove		= cdns_dphy_remove,
+	.driver		= {
+		.name		= "cdns-mipi-dphy",
+		.of_match_table	= cdns_dphy_of_match,
+	},
+};
+module_platform_driver(cdns_dphy_platform_driver);
+
+MODULE_AUTHOR("Maxime Ripard <maxime.ripard@bootlin.com>");
+MODULE_DESCRIPTION("Cadence MIPI D-PHY Driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/phy/freescale/Kconfig b/drivers/phy/freescale/Kconfig
index f050bd4e97e0..832670b4952b 100644
--- a/drivers/phy/freescale/Kconfig
+++ b/drivers/phy/freescale/Kconfig
@@ -2,4 +2,4 @@ config PHY_FSL_IMX8MQ_USB
 	tristate "Freescale i.MX8M USB3 PHY"
 	depends on OF && HAS_IOMEM
 	select GENERIC_PHY
-	default SOC_IMX8MQ
+	default ARCH_MXC && ARM64
diff --git a/drivers/phy/marvell/Kconfig b/drivers/phy/marvell/Kconfig
index 6fb4b56e4c14..b8e9dd38ad0d 100644
--- a/drivers/phy/marvell/Kconfig
+++ b/drivers/phy/marvell/Kconfig
@@ -21,6 +21,27 @@ config PHY_BERLIN_USB
 	help
 	  Enable this to support the USB PHY on Marvell Berlin SoCs.
 
+config PHY_MVEBU_A3700_COMPHY
+	tristate "Marvell A3700 comphy driver"
+	depends on ARCH_MVEBU || COMPILE_TEST
+	depends on OF
+	depends on HAVE_ARM_SMCCC
+	default y
+	select GENERIC_PHY
+	help
+	  This driver allows to control the comphy, a hardware block providing
+	  shared serdes PHYs on Marvell Armada 3700. Its serdes lanes can be
+	  used by various controllers: Ethernet, SATA, USB3, PCIe.
+
+config PHY_MVEBU_A3700_UTMI
+	tristate "Marvell A3700 UTMI driver"
+	depends on ARCH_MVEBU || COMPILE_TEST
+	depends on OF
+	default y
+	select GENERIC_PHY
+	help
+	  Enable this to support Marvell A3700 UTMI PHY driver.
+
 config PHY_MVEBU_CP110_COMPHY
 	tristate "Marvell CP110 comphy driver"
 	depends on ARCH_MVEBU || COMPILE_TEST
diff --git a/drivers/phy/marvell/Makefile b/drivers/phy/marvell/Makefile
index 3975b144f8ec..82f291cf59ee 100644
--- a/drivers/phy/marvell/Makefile
+++ b/drivers/phy/marvell/Makefile
@@ -2,6 +2,8 @@
 obj-$(CONFIG_ARMADA375_USBCLUSTER_PHY)	+= phy-armada375-usb2.o
 obj-$(CONFIG_PHY_BERLIN_SATA)		+= phy-berlin-sata.o
 obj-$(CONFIG_PHY_BERLIN_USB)		+= phy-berlin-usb.o
+obj-$(CONFIG_PHY_MVEBU_A3700_COMPHY)	+= phy-mvebu-a3700-comphy.o
+obj-$(CONFIG_PHY_MVEBU_A3700_UTMI)	+= phy-mvebu-a3700-utmi.o
 obj-$(CONFIG_PHY_MVEBU_CP110_COMPHY)	+= phy-mvebu-cp110-comphy.o
 obj-$(CONFIG_PHY_MVEBU_SATA)		+= phy-mvebu-sata.o
 obj-$(CONFIG_PHY_PXA_28NM_HSIC)		+= phy-pxa-28nm-hsic.o
diff --git a/drivers/phy/marvell/phy-armada375-usb2.c b/drivers/phy/marvell/phy-armada375-usb2.c
index 1a3db288c0a9..fa5dc9462d09 100644
--- a/drivers/phy/marvell/phy-armada375-usb2.c
+++ b/drivers/phy/marvell/phy-armada375-usb2.c
@@ -1,3 +1,4 @@
+// SPDX-License-Identifier: GPL-2.0+
 /*
  * USB cluster support for Armada 375 platform.
  *
@@ -5,10 +6,6 @@
  *
  * Gregory CLEMENT <gregory.clement@free-electrons.com>
  *
- * This file is licensed under the terms of the GNU General Public
- * License version 2 or later. This program is licensed "as is"
- * without any warranty of any kind, whether express or implied.
- *
  * Armada 375 comes with an USB2 host and device controller and an
  * USB3 controller. The USB cluster control register allows to manage
  * common features of both USB controllers.
@@ -18,7 +15,6 @@
 #include <linux/init.h>
 #include <linux/io.h>
 #include <linux/kernel.h>
-#include <linux/module.h>
 #include <linux/of_address.h>
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
@@ -142,7 +138,6 @@ static const struct of_device_id of_usb_cluster_table[] = {
 	{ .compatible = "marvell,armada-375-usb-cluster", },
 	{ /* end of list */ },
 };
-MODULE_DEVICE_TABLE(of, of_usb_cluster_table);
 
 static struct platform_driver armada375_usb_phy_driver = {
 	.probe	= armada375_usb_phy_probe,
@@ -151,8 +146,4 @@ static struct platform_driver armada375_usb_phy_driver = {
 		.name  = "armada-375-usb-cluster",
 	}
 };
-module_platform_driver(armada375_usb_phy_driver);
-
-MODULE_DESCRIPTION("Armada 375 USB cluster driver");
-MODULE_AUTHOR("Gregory CLEMENT <gregory.clement@free-electrons.com>");
-MODULE_LICENSE("GPL");
+builtin_platform_driver(armada375_usb_phy_driver);
diff --git a/drivers/phy/marvell/phy-mvebu-a3700-comphy.c b/drivers/phy/marvell/phy-mvebu-a3700-comphy.c
new file mode 100644
index 000000000000..8812a104c233
--- /dev/null
+++ b/drivers/phy/marvell/phy-mvebu-a3700-comphy.c
@@ -0,0 +1,318 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Marvell
+ *
+ * Authors:
+ *   Evan Wang <xswang@marvell.com>
+ *   Miquèl Raynal <miquel.raynal@bootlin.com>
+ *
+ * Structure inspired from phy-mvebu-cp110-comphy.c written by Antoine Tenart.
+ * SMC call initial support done by Grzegorz Jaszczyk.
+ */
+
+#include <linux/arm-smccc.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/phy.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+
+#define MVEBU_A3700_COMPHY_LANES		3
+#define MVEBU_A3700_COMPHY_PORTS		2
+
+/* COMPHY Fast SMC function identifiers */
+#define COMPHY_SIP_POWER_ON			0x82000001
+#define COMPHY_SIP_POWER_OFF			0x82000002
+#define COMPHY_SIP_PLL_LOCK			0x82000003
+
+#define COMPHY_FW_MODE_SATA			0x1
+#define COMPHY_FW_MODE_SGMII			0x2
+#define COMPHY_FW_MODE_HS_SGMII			0x3
+#define COMPHY_FW_MODE_USB3H			0x4
+#define COMPHY_FW_MODE_USB3D			0x5
+#define COMPHY_FW_MODE_PCIE			0x6
+#define COMPHY_FW_MODE_RXAUI			0x7
+#define COMPHY_FW_MODE_XFI			0x8
+#define COMPHY_FW_MODE_SFI			0x9
+#define COMPHY_FW_MODE_USB3			0xa
+
+#define COMPHY_FW_SPEED_1_25G			0 /* SGMII 1G */
+#define COMPHY_FW_SPEED_2_5G			1
+#define COMPHY_FW_SPEED_3_125G			2 /* SGMII 2.5G */
+#define COMPHY_FW_SPEED_5G			3
+#define COMPHY_FW_SPEED_5_15625G		4 /* XFI 5G */
+#define COMPHY_FW_SPEED_6G			5
+#define COMPHY_FW_SPEED_10_3125G		6 /* XFI 10G */
+#define COMPHY_FW_SPEED_MAX			0x3F
+
+#define COMPHY_FW_MODE(mode)			((mode) << 12)
+#define COMPHY_FW_NET(mode, idx, speed)		(COMPHY_FW_MODE(mode) | \
+						 ((idx) << 8) |	\
+						 ((speed) << 2))
+#define COMPHY_FW_PCIE(mode, idx, speed, width)	(COMPHY_FW_NET(mode, idx, speed) | \
+						 ((width) << 18))
+
+struct mvebu_a3700_comphy_conf {
+	unsigned int lane;
+	enum phy_mode mode;
+	int submode;
+	unsigned int port;
+	u32 fw_mode;
+};
+
+#define MVEBU_A3700_COMPHY_CONF(_lane, _mode, _smode, _port, _fw)	\
+	{								\
+		.lane = _lane,						\
+		.mode = _mode,						\
+		.submode = _smode,					\
+		.port = _port,						\
+		.fw_mode = _fw,						\
+	}
+
+#define MVEBU_A3700_COMPHY_CONF_GEN(_lane, _mode, _port, _fw) \
+	MVEBU_A3700_COMPHY_CONF(_lane, _mode, PHY_INTERFACE_MODE_NA, _port, _fw)
+
+#define MVEBU_A3700_COMPHY_CONF_ETH(_lane, _smode, _port, _fw) \
+	MVEBU_A3700_COMPHY_CONF(_lane, PHY_MODE_ETHERNET, _smode, _port, _fw)
+
+static const struct mvebu_a3700_comphy_conf mvebu_a3700_comphy_modes[] = {
+	/* lane 0 */
+	MVEBU_A3700_COMPHY_CONF_GEN(0, PHY_MODE_USB_HOST_SS, 0,
+				    COMPHY_FW_MODE_USB3H),
+	MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_SGMII, 1,
+				    COMPHY_FW_MODE_SGMII),
+	MVEBU_A3700_COMPHY_CONF_ETH(0, PHY_INTERFACE_MODE_2500BASEX, 1,
+				    COMPHY_FW_MODE_HS_SGMII),
+	/* lane 1 */
+	MVEBU_A3700_COMPHY_CONF_GEN(1, PHY_MODE_PCIE, 0,
+				    COMPHY_FW_MODE_PCIE),
+	MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_SGMII, 0,
+				    COMPHY_FW_MODE_SGMII),
+	MVEBU_A3700_COMPHY_CONF_ETH(1, PHY_INTERFACE_MODE_2500BASEX, 0,
+				    COMPHY_FW_MODE_HS_SGMII),
+	/* lane 2 */
+	MVEBU_A3700_COMPHY_CONF_GEN(2, PHY_MODE_SATA, 0,
+				    COMPHY_FW_MODE_SATA),
+	MVEBU_A3700_COMPHY_CONF_GEN(2, PHY_MODE_USB_HOST_SS, 0,
+				    COMPHY_FW_MODE_USB3H),
+};
+
+struct mvebu_a3700_comphy_lane {
+	struct device *dev;
+	unsigned int id;
+	enum phy_mode mode;
+	int submode;
+	int port;
+};
+
+static int mvebu_a3700_comphy_smc(unsigned long function, unsigned long lane,
+				  unsigned long mode)
+{
+	struct arm_smccc_res res;
+
+	arm_smccc_smc(function, lane, mode, 0, 0, 0, 0, 0, &res);
+
+	return res.a0;
+}
+
+static int mvebu_a3700_comphy_get_fw_mode(int lane, int port,
+					  enum phy_mode mode,
+					  int submode)
+{
+	int i, n = ARRAY_SIZE(mvebu_a3700_comphy_modes);
+
+	/* Unused PHY mux value is 0x0 */
+	if (mode == PHY_MODE_INVALID)
+		return -EINVAL;
+
+	for (i = 0; i < n; i++) {
+		if (mvebu_a3700_comphy_modes[i].lane == lane &&
+		    mvebu_a3700_comphy_modes[i].port == port &&
+		    mvebu_a3700_comphy_modes[i].mode == mode &&
+		    mvebu_a3700_comphy_modes[i].submode == submode)
+			break;
+	}
+
+	if (i == n)
+		return -EINVAL;
+
+	return mvebu_a3700_comphy_modes[i].fw_mode;
+}
+
+static int mvebu_a3700_comphy_set_mode(struct phy *phy, enum phy_mode mode,
+				       int submode)
+{
+	struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
+	int fw_mode;
+
+	if (submode == PHY_INTERFACE_MODE_1000BASEX)
+		submode = PHY_INTERFACE_MODE_SGMII;
+
+	fw_mode = mvebu_a3700_comphy_get_fw_mode(lane->id, lane->port, mode,
+						 submode);
+	if (fw_mode < 0) {
+		dev_err(lane->dev, "invalid COMPHY mode\n");
+		return fw_mode;
+	}
+
+	/* Just remember the mode, ->power_on() will do the real setup */
+	lane->mode = mode;
+	lane->submode = submode;
+
+	return 0;
+}
+
+static int mvebu_a3700_comphy_power_on(struct phy *phy)
+{
+	struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
+	u32 fw_param;
+	int fw_mode;
+
+	fw_mode = mvebu_a3700_comphy_get_fw_mode(lane->id, lane->port,
+						 lane->mode, lane->submode);
+	if (fw_mode < 0) {
+		dev_err(lane->dev, "invalid COMPHY mode\n");
+		return fw_mode;
+	}
+
+	switch (lane->mode) {
+	case PHY_MODE_USB_HOST_SS:
+		dev_dbg(lane->dev, "set lane %d to USB3 host mode\n", lane->id);
+		fw_param = COMPHY_FW_MODE(fw_mode);
+		break;
+	case PHY_MODE_SATA:
+		dev_dbg(lane->dev, "set lane %d to SATA mode\n", lane->id);
+		fw_param = COMPHY_FW_MODE(fw_mode);
+		break;
+	case PHY_MODE_ETHERNET:
+		switch (lane->submode) {
+		case PHY_INTERFACE_MODE_SGMII:
+			dev_dbg(lane->dev, "set lane %d to SGMII mode\n",
+				lane->id);
+			fw_param = COMPHY_FW_NET(fw_mode, lane->port,
+						 COMPHY_FW_SPEED_1_25G);
+			break;
+		case PHY_INTERFACE_MODE_2500BASEX:
+			dev_dbg(lane->dev, "set lane %d to HS SGMII mode\n",
+				lane->id);
+			fw_param = COMPHY_FW_NET(fw_mode, lane->port,
+						 COMPHY_FW_SPEED_3_125G);
+			break;
+		default:
+			dev_err(lane->dev, "unsupported PHY submode (%d)\n",
+				lane->submode);
+			return -ENOTSUPP;
+		}
+		break;
+	case PHY_MODE_PCIE:
+		dev_dbg(lane->dev, "set lane %d to PCIe mode\n", lane->id);
+		fw_param = COMPHY_FW_PCIE(fw_mode, lane->port,
+					  COMPHY_FW_SPEED_5G,
+					  phy->attrs.bus_width);
+		break;
+	default:
+		dev_err(lane->dev, "unsupported PHY mode (%d)\n", lane->mode);
+		return -ENOTSUPP;
+	}
+
+	return mvebu_a3700_comphy_smc(COMPHY_SIP_POWER_ON, lane->id, fw_param);
+}
+
+static int mvebu_a3700_comphy_power_off(struct phy *phy)
+{
+	struct mvebu_a3700_comphy_lane *lane = phy_get_drvdata(phy);
+
+	return mvebu_a3700_comphy_smc(COMPHY_SIP_POWER_OFF, lane->id, 0);
+}
+
+static const struct phy_ops mvebu_a3700_comphy_ops = {
+	.power_on	= mvebu_a3700_comphy_power_on,
+	.power_off	= mvebu_a3700_comphy_power_off,
+	.set_mode	= mvebu_a3700_comphy_set_mode,
+	.owner		= THIS_MODULE,
+};
+
+static struct phy *mvebu_a3700_comphy_xlate(struct device *dev,
+					    struct of_phandle_args *args)
+{
+	struct mvebu_a3700_comphy_lane *lane;
+	struct phy *phy;
+
+	if (WARN_ON(args->args[0] >= MVEBU_A3700_COMPHY_PORTS))
+		return ERR_PTR(-EINVAL);
+
+	phy = of_phy_simple_xlate(dev, args);
+	if (IS_ERR(phy))
+		return phy;
+
+	lane = phy_get_drvdata(phy);
+	lane->port = args->args[0];
+
+	return phy;
+}
+
+static int mvebu_a3700_comphy_probe(struct platform_device *pdev)
+{
+	struct phy_provider *provider;
+	struct device_node *child;
+
+	for_each_available_child_of_node(pdev->dev.of_node, child) {
+		struct mvebu_a3700_comphy_lane *lane;
+		struct phy *phy;
+		int ret;
+		u32 lane_id;
+
+		ret = of_property_read_u32(child, "reg", &lane_id);
+		if (ret < 0) {
+			dev_err(&pdev->dev, "missing 'reg' property (%d)\n",
+				ret);
+			continue;
+		}
+
+		if (lane_id >= MVEBU_A3700_COMPHY_LANES) {
+			dev_err(&pdev->dev, "invalid 'reg' property\n");
+			continue;
+		}
+
+		lane = devm_kzalloc(&pdev->dev, sizeof(*lane), GFP_KERNEL);
+		if (!lane)
+			return -ENOMEM;
+
+		phy = devm_phy_create(&pdev->dev, child,
+				      &mvebu_a3700_comphy_ops);
+		if (IS_ERR(phy))
+			return PTR_ERR(phy);
+
+		lane->dev = &pdev->dev;
+		lane->mode = PHY_MODE_INVALID;
+		lane->submode = PHY_INTERFACE_MODE_NA;
+		lane->id = lane_id;
+		lane->port = -1;
+		phy_set_drvdata(phy, lane);
+	}
+
+	provider = devm_of_phy_provider_register(&pdev->dev,
+						 mvebu_a3700_comphy_xlate);
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static const struct of_device_id mvebu_a3700_comphy_of_match_table[] = {
+	{ .compatible = "marvell,comphy-a3700" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mvebu_a3700_comphy_of_match_table);
+
+static struct platform_driver mvebu_a3700_comphy_driver = {
+	.probe	= mvebu_a3700_comphy_probe,
+	.driver	= {
+		.name = "mvebu-a3700-comphy",
+		.of_match_table = mvebu_a3700_comphy_of_match_table,
+	},
+};
+module_platform_driver(mvebu_a3700_comphy_driver);
+
+MODULE_AUTHOR("Miquèl Raynal <miquel.raynal@bootlin.com>");
+MODULE_DESCRIPTION("Common PHY driver for A3700");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/marvell/phy-mvebu-a3700-utmi.c b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
new file mode 100644
index 000000000000..94a29dea57af
--- /dev/null
+++ b/drivers/phy/marvell/phy-mvebu-a3700-utmi.c
@@ -0,0 +1,278 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) 2018 Marvell
+ *
+ * Authors:
+ *   Igal Liberman <igall@marvell.com>
+ *   Miquèl Raynal <miquel.raynal@bootlin.com>
+ *
+ * Marvell A3700 UTMI PHY driver
+ */
+
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/phy/phy.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* Armada 3700 UTMI PHY registers */
+#define USB2_PHY_PLL_CTRL_REG0			0x0
+#define   PLL_REF_DIV_OFF			0
+#define   PLL_REF_DIV_MASK			GENMASK(6, 0)
+#define   PLL_REF_DIV_5				5
+#define   PLL_FB_DIV_OFF			16
+#define   PLL_FB_DIV_MASK			GENMASK(24, 16)
+#define   PLL_FB_DIV_96				96
+#define   PLL_SEL_LPFR_OFF			28
+#define   PLL_SEL_LPFR_MASK			GENMASK(29, 28)
+#define   PLL_READY				BIT(31)
+#define USB2_PHY_CAL_CTRL			0x8
+#define   PHY_PLLCAL_DONE			BIT(31)
+#define   PHY_IMPCAL_DONE			BIT(23)
+#define USB2_RX_CHAN_CTRL1			0x18
+#define   USB2PHY_SQCAL_DONE			BIT(31)
+#define USB2_PHY_OTG_CTRL			0x34
+#define   PHY_PU_OTG				BIT(4)
+#define USB2_PHY_CHRGR_DETECT			0x38
+#define   PHY_CDP_EN				BIT(2)
+#define   PHY_DCP_EN				BIT(3)
+#define   PHY_PD_EN				BIT(4)
+#define   PHY_PU_CHRG_DTC			BIT(5)
+#define   PHY_CDP_DM_AUTO			BIT(7)
+#define   PHY_ENSWITCH_DP			BIT(12)
+#define   PHY_ENSWITCH_DM			BIT(13)
+
+/* Armada 3700 USB miscellaneous registers */
+#define USB2_PHY_CTRL(usb32)			(usb32 ? 0x20 : 0x4)
+#define   RB_USB2PHY_PU				BIT(0)
+#define   USB2_DP_PULLDN_DEV_MODE		BIT(5)
+#define   USB2_DM_PULLDN_DEV_MODE		BIT(6)
+#define   RB_USB2PHY_SUSPM(usb32)		(usb32 ? BIT(14) : BIT(7))
+
+#define PLL_LOCK_DELAY_US			10000
+#define PLL_LOCK_TIMEOUT_US			1000000
+
+/**
+ * struct mvebu_a3700_utmi_caps - PHY capabilities
+ *
+ * @usb32: Flag indicating which PHY is in use (impacts the register map):
+ *           - The UTMI PHY wired to the USB3/USB2 controller (otg)
+ *           - The UTMI PHY wired to the USB2 controller (host only)
+ * @ops: PHY operations
+ */
+struct mvebu_a3700_utmi_caps {
+	int usb32;
+	const struct phy_ops *ops;
+};
+
+/**
+ * struct mvebu_a3700_utmi - PHY driver data
+ *
+ * @regs: PHY registers
+ * @usb_mis: Regmap with USB miscellaneous registers including PHY ones
+ * @caps: PHY capabilities
+ * @phy: PHY handle
+ */
+struct mvebu_a3700_utmi {
+	void __iomem *regs;
+	struct regmap *usb_misc;
+	const struct mvebu_a3700_utmi_caps *caps;
+	struct phy *phy;
+};
+
+static int mvebu_a3700_utmi_phy_power_on(struct phy *phy)
+{
+	struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
+	struct device *dev = &phy->dev;
+	int usb32 = utmi->caps->usb32;
+	int ret = 0;
+	u32 reg;
+
+	/*
+	 * Setup PLL. 40MHz clock used to be the default, being 25MHz now.
+	 * See "PLL Settings for Typical REFCLK" table.
+	 */
+	reg = readl(utmi->regs + USB2_PHY_PLL_CTRL_REG0);
+	reg &= ~(PLL_REF_DIV_MASK | PLL_FB_DIV_MASK | PLL_SEL_LPFR_MASK);
+	reg |= (PLL_REF_DIV_5 << PLL_REF_DIV_OFF) |
+	       (PLL_FB_DIV_96 << PLL_FB_DIV_OFF);
+	writel(reg, utmi->regs + USB2_PHY_PLL_CTRL_REG0);
+
+	/* Enable PHY pull up and disable USB2 suspend */
+	regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
+			   RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU,
+			   RB_USB2PHY_SUSPM(usb32) | RB_USB2PHY_PU);
+
+	if (usb32) {
+		/* Power up OTG module */
+		reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
+		reg |= PHY_PU_OTG;
+		writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
+
+		/* Disable PHY charger detection */
+		reg = readl(utmi->regs + USB2_PHY_CHRGR_DETECT);
+		reg &= ~(PHY_CDP_EN | PHY_DCP_EN | PHY_PD_EN | PHY_PU_CHRG_DTC |
+			 PHY_CDP_DM_AUTO | PHY_ENSWITCH_DP | PHY_ENSWITCH_DM);
+		writel(reg, utmi->regs + USB2_PHY_CHRGR_DETECT);
+
+		/* Disable PHY DP/DM pull-down (used for device mode) */
+		regmap_update_bits(utmi->usb_misc, USB2_PHY_CTRL(usb32),
+				   USB2_DP_PULLDN_DEV_MODE |
+				   USB2_DM_PULLDN_DEV_MODE, 0);
+	}
+
+	/* Wait for PLL calibration */
+	ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
+				 reg & PHY_PLLCAL_DONE,
+				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+	if (ret) {
+		dev_err(dev, "Failed to end USB2 PLL calibration\n");
+		return ret;
+	}
+
+	/* Wait for impedance calibration */
+	ret = readl_poll_timeout(utmi->regs + USB2_PHY_CAL_CTRL, reg,
+				 reg & PHY_IMPCAL_DONE,
+				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+	if (ret) {
+		dev_err(dev, "Failed to end USB2 impedance calibration\n");
+		return ret;
+	}
+
+	/* Wait for squelch calibration */
+	ret = readl_poll_timeout(utmi->regs + USB2_RX_CHAN_CTRL1, reg,
+				 reg & USB2PHY_SQCAL_DONE,
+				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+	if (ret) {
+		dev_err(dev, "Failed to end USB2 unknown calibration\n");
+		return ret;
+	}
+
+	/* Wait for PLL to be locked */
+	ret = readl_poll_timeout(utmi->regs + USB2_PHY_PLL_CTRL_REG0, reg,
+				 reg & PLL_READY,
+				 PLL_LOCK_DELAY_US, PLL_LOCK_TIMEOUT_US);
+	if (ret)
+		dev_err(dev, "Failed to lock USB2 PLL\n");
+
+	return ret;
+}
+
+static int mvebu_a3700_utmi_phy_power_off(struct phy *phy)
+{
+	struct mvebu_a3700_utmi *utmi = phy_get_drvdata(phy);
+	int usb32 = utmi->caps->usb32;
+	u32 reg;
+
+	/* Disable PHY pull-up and enable USB2 suspend */
+	reg = readl(utmi->regs + USB2_PHY_CTRL(usb32));
+	reg &= ~(RB_USB2PHY_PU | RB_USB2PHY_SUSPM(usb32));
+	writel(reg, utmi->regs + USB2_PHY_CTRL(usb32));
+
+	/* Power down OTG module */
+	if (usb32) {
+		reg = readl(utmi->regs + USB2_PHY_OTG_CTRL);
+		reg &= ~PHY_PU_OTG;
+		writel(reg, utmi->regs + USB2_PHY_OTG_CTRL);
+	}
+
+	return 0;
+}
+
+static const struct phy_ops mvebu_a3700_utmi_phy_ops = {
+	.power_on = mvebu_a3700_utmi_phy_power_on,
+	.power_off = mvebu_a3700_utmi_phy_power_off,
+	.owner = THIS_MODULE,
+};
+
+static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_otg_phy_caps = {
+	.usb32 = true,
+	.ops = &mvebu_a3700_utmi_phy_ops,
+};
+
+static const struct mvebu_a3700_utmi_caps mvebu_a3700_utmi_host_phy_caps = {
+	.usb32 = false,
+	.ops = &mvebu_a3700_utmi_phy_ops,
+};
+
+static const struct of_device_id mvebu_a3700_utmi_of_match[] = {
+	{
+		.compatible = "marvell,a3700-utmi-otg-phy",
+		.data = &mvebu_a3700_utmi_otg_phy_caps,
+	},
+	{
+		.compatible = "marvell,a3700-utmi-host-phy",
+		.data = &mvebu_a3700_utmi_host_phy_caps,
+	},
+	{},
+};
+MODULE_DEVICE_TABLE(of, mvebu_a3700_utmi_of_match);
+
+static int mvebu_a3700_utmi_phy_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct mvebu_a3700_utmi *utmi;
+	struct phy_provider *provider;
+	struct resource *res;
+
+	utmi = devm_kzalloc(dev, sizeof(*utmi), GFP_KERNEL);
+	if (!utmi)
+		return -ENOMEM;
+
+	/* Get UTMI memory region */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(dev, "Missing UTMI PHY memory resource\n");
+		return -ENODEV;
+	}
+
+	utmi->regs = devm_ioremap_resource(dev, res);
+	if (IS_ERR(utmi->regs))
+		return PTR_ERR(utmi->regs);
+
+	/* Get miscellaneous Host/PHY region */
+	utmi->usb_misc = syscon_regmap_lookup_by_phandle(dev->of_node,
+							 "marvell,usb-misc-reg");
+	if (IS_ERR(utmi->usb_misc)) {
+		dev_err(dev,
+			"Missing USB misc purpose system controller\n");
+		return PTR_ERR(utmi->usb_misc);
+	}
+
+	/* Retrieve PHY capabilities */
+	utmi->caps = of_device_get_match_data(dev);
+
+	/* Instantiate the PHY */
+	utmi->phy = devm_phy_create(dev, NULL, utmi->caps->ops);
+	if (IS_ERR(utmi->phy)) {
+		dev_err(dev, "Failed to create the UTMI PHY\n");
+		return PTR_ERR(utmi->phy);
+	}
+
+	phy_set_drvdata(utmi->phy, utmi);
+
+	/* Ensure the PHY is powered off */
+	utmi->caps->ops->power_off(utmi->phy);
+
+	provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
+
+	return PTR_ERR_OR_ZERO(provider);
+}
+
+static struct platform_driver mvebu_a3700_utmi_driver = {
+	.probe	= mvebu_a3700_utmi_phy_probe,
+	.driver	= {
+		.name		= "mvebu-a3700-utmi-phy",
+		.owner		= THIS_MODULE,
+		.of_match_table	= mvebu_a3700_utmi_of_match,
+	 },
+};
+module_platform_driver(mvebu_a3700_utmi_driver);
+
+MODULE_AUTHOR("Igal Liberman <igall@marvell.com>");
+MODULE_AUTHOR("Miquel Raynal <miquel.raynal@bootlin.com>");
+MODULE_DESCRIPTION("Marvell EBU A3700 UTMI PHY driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/phy/marvell/phy-mvebu-cp110-comphy.c b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
index 187cccde53b5..d98e0451f6a1 100644
--- a/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
+++ b/drivers/phy/marvell/phy-mvebu-cp110-comphy.c
@@ -580,8 +580,6 @@ static struct phy *mvebu_comphy_xlate(struct device *dev,
 		return phy;
 
 	lane = phy_get_drvdata(phy);
-	if (lane->port >= 0)
-		return ERR_PTR(-EBUSY);
 	lane->port = args->args[0];
 
 	return phy;
diff --git a/drivers/phy/marvell/phy-mvebu-sata.c b/drivers/phy/marvell/phy-mvebu-sata.c
index 768ce92e81ce..369fece2be7a 100644
--- a/drivers/phy/marvell/phy-mvebu-sata.c
+++ b/drivers/phy/marvell/phy-mvebu-sata.c
@@ -10,7 +10,7 @@
  */
 
 #include <linux/kernel.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/clk.h>
 #include <linux/phy/phy.h>
 #include <linux/io.h>
@@ -122,7 +122,6 @@ static const struct of_device_id phy_mvebu_sata_of_match[] = {
 	{ .compatible = "marvell,mvebu-sata-phy" },
 	{ },
 };
-MODULE_DEVICE_TABLE(of, phy_mvebu_sata_of_match);
 
 static struct platform_driver phy_mvebu_sata_driver = {
 	.probe	= phy_mvebu_sata_probe,
@@ -131,8 +130,4 @@ static struct platform_driver phy_mvebu_sata_driver = {
 		.of_match_table	= phy_mvebu_sata_of_match,
 	}
 };
-module_platform_driver(phy_mvebu_sata_driver);
-
-MODULE_AUTHOR("Andrew Lunn <andrew@lunn.ch>");
-MODULE_DESCRIPTION("Marvell MVEBU SATA PHY driver");
-MODULE_LICENSE("GPL v2");
+builtin_platform_driver(phy_mvebu_sata_driver);
diff --git a/drivers/phy/phy-core-mipi-dphy.c b/drivers/phy/phy-core-mipi-dphy.c
index 465fa1b91a5f..14e0551cd319 100644
--- a/drivers/phy/phy-core-mipi-dphy.c
+++ b/drivers/phy/phy-core-mipi-dphy.c
@@ -65,12 +65,12 @@ int phy_mipi_dphy_get_default_config(unsigned long pixel_clock,
 	 */
 	cfg->hs_trail = max(4 * 8 * ui, 60000 + 4 * 4 * ui);
 
-	cfg->init = 100000000;
+	cfg->init = 100;
 	cfg->lpx = 60000;
 	cfg->ta_get = 5 * cfg->lpx;
 	cfg->ta_go = 4 * cfg->lpx;
 	cfg->ta_sure = 2 * cfg->lpx;
-	cfg->wakeup = 1000000000;
+	cfg->wakeup = 1000;
 
 	cfg->hs_clk_rate = hs_clk_rate;
 	cfg->lanes = lanes;
@@ -143,7 +143,7 @@ int phy_mipi_dphy_config_validate(struct phy_configure_opts_mipi_dphy *cfg)
 	if (cfg->hs_trail < max(8 * ui, 60000 + 4 * ui))
 		return -EINVAL;
 
-	if (cfg->init < 100000000)
+	if (cfg->init < 100)
 		return -EINVAL;
 
 	if (cfg->lpx < 50000)
@@ -158,7 +158,7 @@ int phy_mipi_dphy_config_validate(struct phy_configure_opts_mipi_dphy *cfg)
 	if (cfg->ta_sure < cfg->lpx || cfg->ta_sure > (2 * cfg->lpx))
 		return -EINVAL;
 
-	if (cfg->wakeup < 1000000000)
+	if (cfg->wakeup < 1000)
 		return -EINVAL;
 
 	return 0;
diff --git a/drivers/phy/phy-core.c b/drivers/phy/phy-core.c
index 19b05e824ee4..cb38f6e8614c 100644
--- a/drivers/phy/phy-core.c
+++ b/drivers/phy/phy-core.c
@@ -1112,14 +1112,4 @@ static int __init phy_core_init(void)
 
 	return 0;
 }
-module_init(phy_core_init);
-
-static void __exit phy_core_exit(void)
-{
-	class_destroy(phy_class);
-}
-module_exit(phy_core_exit);
-
-MODULE_DESCRIPTION("Generic PHY Framework");
-MODULE_AUTHOR("Kishon Vijay Abraham I <kishon@ti.com>");
-MODULE_LICENSE("GPL v2");
+device_initcall(phy_core_init);
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index b4006818e1b6..08d6f6f7f039 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -687,6 +687,116 @@ static const struct qmp_phy_init_tbl sdm845_ufsphy_pcs_tbl[] = {
 	QMP_PHY_INIT_CFG(QPHY_V3_PCS_MULTI_LANE_CTRL1, 0x02),
 };
 
+static const struct qmp_phy_init_tbl msm8998_usb3_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CLK_SELECT, 0x30),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BIAS_EN_CLKBUFLR_EN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYSCLK_EN_SEL, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SYS_CLK_CTRL, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_RESETSM_CNTRL2, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_CONFIG, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SVS_MODE_CLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_HSCLK_SEL, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DEC_START_MODE0, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START1_MODE0, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START2_MODE0, 0xea),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_DIV_FRAC_START3_MODE0, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CP_CTRL_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE2_MODE0, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE1_MODE0, 0xc9),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORECLK_DIV_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP3_MODE0, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP2_MODE0, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP1_MODE0, 0x15),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_EN, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CORE_CLK_EN, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_LOCK_CMP_CFG, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_VCO_TUNE_MAP, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_BG_TIMER, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_PLL_IVCO, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_INTEGLOOP_INITVAL, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_CMN_MODE, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER1, 0x31),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_PER2, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_ADJ_PER2, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE1, 0x85),
+	QMP_PHY_INIT_CFG(QSERDES_V3_COM_SSC_STEP_SIZE2, 0x07),
+};
+
+static const struct qmp_phy_init_tbl msm8998_usb3_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_HIGHZ_DRVR_EN, 0x10),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_RCV_DETECT_LVL_2, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_LANE_MODE_1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX, 0x00),
+};
+
+static const struct qmp_phy_init_tbl msm8998_usb3_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN, 0x0b),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4e),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQU_ADAPTOR_CNTRL4, 0x18),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_CNTRL, 0x43),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_DEGLITCH_CNTRL, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x75),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_COUNT_LOW, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FASTLOCK_COUNT_HIGH, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_PI_CONTROLS, 0x80),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_FO_GAIN, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_UCDR_SO_GAIN, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_SIGDET_ENABLES, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_VGA_CAL_CNTRL2, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V3_RX_RX_MODE_00, 0x05),
+};
+
+static const struct qmp_phy_init_tbl msm8998_usb3_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL2, 0x83),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_L, 0x09),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNT_VAL_H_TOL, 0xa2),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_MAN_CODE, 0x40),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_FLL_CNTRL1, 0x02),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG1, 0xd1),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG2, 0x1f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LOCK_DETECT_CONFIG3, 0x47),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_POWER_STATE_CONFIG2, 0x1b),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V0, 0x9f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V1, 0x9f),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V2, 0xb7),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V3, 0x4e),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_V4, 0x65),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXMGN_LS, 0x6b),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V0, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V0, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TX_LARGE_AMP_DRV_LVL, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V1, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V2, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V2, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V3, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V3, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_V4, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_V4, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M6DB_LS, 0x15),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TXDEEMPH_M3P5DB_LS, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RATE_SLEW_CNTRL, 0x02),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_PWRUP_RESET_DLY_TIME_AUXCLK, 0x04),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_TSYNC_RSYNC_TIME, 0x44),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_L, 0xe7),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_P1U2_H, 0x03),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_L, 0x40),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RCVR_DTCT_DLY_U3_H, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RX_SIGDET_LVL, 0x8a),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_WAIT_TIME, 0x75),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_LFPS_TX_ECSTART_EQTLOCK, 0x86),
+	QMP_PHY_INIT_CFG(QPHY_V3_PCS_RXEQTRAINING_RUN_TIME, 0x13),
+};
+
+
 /* struct qmp_phy_cfg - per-PHY initialization config */
 struct qmp_phy_cfg {
 	/* phy-type - PCIE/UFS/USB */
@@ -1036,6 +1146,33 @@ static const struct qmp_phy_cfg sdm845_ufsphy_cfg = {
 	.no_pcs_sw_reset	= true,
 };
 
+static const struct qmp_phy_cfg msm8998_usb3phy_cfg = {
+	.type                   = PHY_TYPE_USB3,
+	.nlanes                 = 1,
+
+	.serdes_tbl             = msm8998_usb3_serdes_tbl,
+	.serdes_tbl_num         = ARRAY_SIZE(msm8998_usb3_serdes_tbl),
+	.tx_tbl                 = msm8998_usb3_tx_tbl,
+	.tx_tbl_num             = ARRAY_SIZE(msm8998_usb3_tx_tbl),
+	.rx_tbl                 = msm8998_usb3_rx_tbl,
+	.rx_tbl_num             = ARRAY_SIZE(msm8998_usb3_rx_tbl),
+	.pcs_tbl                = msm8998_usb3_pcs_tbl,
+	.pcs_tbl_num            = ARRAY_SIZE(msm8998_usb3_pcs_tbl),
+	.clk_list               = msm8996_phy_clk_l,
+	.num_clks               = ARRAY_SIZE(msm8996_phy_clk_l),
+	.reset_list             = msm8996_usb3phy_reset_l,
+	.num_resets             = ARRAY_SIZE(msm8996_usb3phy_reset_l),
+	.vreg_list              = qmp_phy_vreg_l,
+	.num_vregs              = ARRAY_SIZE(qmp_phy_vreg_l),
+	.regs                   = qmp_v3_usb3phy_regs_layout,
+
+	.start_ctrl             = SERDES_START | PCS_START,
+	.pwrdn_ctrl             = SW_PWRDN,
+	.mask_pcs_ready         = PHYSTATUS,
+
+	.is_dual_lane_phy       = true,
+};
+
 static void qcom_qmp_phy_configure(void __iomem *base,
 				   const unsigned int *regs,
 				   const struct qmp_phy_init_tbl tbl[],
@@ -1736,6 +1873,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
 		.compatible = "qcom,msm8996-qmp-usb3-phy",
 		.data = &msm8996_usb3phy_cfg,
 	}, {
+		.compatible = "qcom,msm8998-qmp-ufs-phy",
+		.data = &sdm845_ufsphy_cfg,
+	}, {
 		.compatible = "qcom,ipq8074-qmp-pcie-phy",
 		.data = &ipq8074_pciephy_cfg,
 	}, {
@@ -1747,6 +1887,9 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
 	}, {
 		.compatible = "qcom,sdm845-qmp-ufs-phy",
 		.data = &sdm845_ufsphy_cfg,
+	}, {
+		.compatible = "qcom,msm8998-qmp-usb3-phy",
+		.data = &msm8998_usb3phy_cfg,
 	},
 	{ },
 };
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index d201cc307151..a1b6cdee9a08 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -174,6 +174,7 @@
 #define QSERDES_V3_COM_DIV_FRAC_START1_MODE1		0x0c4
 #define QSERDES_V3_COM_DIV_FRAC_START2_MODE1		0x0c8
 #define QSERDES_V3_COM_DIV_FRAC_START3_MODE1		0x0cc
+#define QSERDES_V3_COM_INTEGLOOP_INITVAL		0x0d0
 #define QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE0		0x0d8
 #define QSERDES_V3_COM_INTEGLOOP_GAIN1_MODE0		0x0dc
 #define QSERDES_V3_COM_INTEGLOOP_GAIN0_MODE1		0x0e0
@@ -201,6 +202,7 @@
 #define QSERDES_V3_COM_DEBUG_BUS2			0x170
 #define QSERDES_V3_COM_DEBUG_BUS3			0x174
 #define QSERDES_V3_COM_DEBUG_BUS_SEL			0x178
+#define QSERDES_V3_COM_CMN_MODE				0x184
 
 /* Only for QMP V3 PHY - TX registers */
 #define QSERDES_V3_TX_RES_CODE_LANE_OFFSET_TX		0x044
@@ -211,6 +213,7 @@
 #define QSERDES_V3_TX_RCV_DETECT_LVL_2			0x0a4
 
 /* Only for QMP V3 PHY - RX registers */
+#define QSERDES_V3_RX_UCDR_FO_GAIN			0x008
 #define QSERDES_V3_RX_UCDR_SO_GAIN_HALF			0x00c
 #define QSERDES_V3_RX_UCDR_SO_GAIN			0x014
 #define QSERDES_V3_RX_UCDR_SVS_SO_GAIN_HALF		0x024
@@ -219,6 +222,7 @@
 #define QSERDES_V3_RX_UCDR_FASTLOCK_FO_GAIN		0x030
 #define QSERDES_V3_RX_UCDR_SO_SATURATION_AND_ENABLE	0x034
 #define QSERDES_V3_RX_UCDR_FASTLOCK_COUNT_LOW		0x03c
+#define QSERDES_V3_RX_UCDR_FASTLOCK_COUNT_HIGH		0x040
 #define QSERDES_V3_RX_UCDR_PI_CONTROLS			0x044
 #define QSERDES_V3_RX_RX_TERM_BW			0x07c
 #define QSERDES_V3_RX_VGA_CAL_CNTRL1			0x0bc
diff --git a/drivers/phy/qualcomm/phy-qcom-qusb2.c b/drivers/phy/qualcomm/phy-qcom-qusb2.c
index 9177989f22d1..8fd7ce139772 100644
--- a/drivers/phy/qualcomm/phy-qcom-qusb2.c
+++ b/drivers/phy/qualcomm/phy-qcom-qusb2.c
@@ -152,6 +152,31 @@ static const struct qusb2_phy_init_tbl msm8996_init_tbl[] = {
 	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_PWR_CTRL, 0x00),
 };
 
+static const unsigned int msm8998_regs_layout[] = {
+	[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE] = 0xa8,
+	[QUSB2PHY_PLL_STATUS]              = 0x1a0,
+	[QUSB2PHY_PORT_TUNE1]              = 0x23c,
+	[QUSB2PHY_PORT_TUNE2]              = 0x240,
+	[QUSB2PHY_PORT_TUNE3]              = 0x244,
+	[QUSB2PHY_PORT_TUNE4]              = 0x248,
+	[QUSB2PHY_PORT_TEST1]              = 0x24c,
+	[QUSB2PHY_PORT_TEST2]              = 0x250,
+	[QUSB2PHY_PORT_POWERDOWN]          = 0x210,
+	[QUSB2PHY_INTR_CTRL]               = 0x22c,
+};
+
+static const struct qusb2_phy_init_tbl msm8998_init_tbl[] = {
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_ANALOG_CONTROLS_TWO, 0x13),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CLOCK_INVERTERS, 0x7c),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_CMODE, 0x80),
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_LOCK_DELAY, 0x0a),
+
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE1, 0xa5),
+	QUSB2_PHY_INIT_CFG_L(QUSB2PHY_PORT_TUNE2, 0x09),
+
+	QUSB2_PHY_INIT_CFG(QUSB2PHY_PLL_DIGITAL_TIMERS_TWO, 0x19),
+};
+
 static const unsigned int sdm845_regs_layout[] = {
 	[QUSB2PHY_PLL_CORE_INPUT_OVERRIDE] = 0xa8,
 	[QUSB2PHY_PLL_STATUS]		= 0x1a0,
@@ -221,6 +246,18 @@ static const struct qusb2_phy_cfg msm8996_phy_cfg = {
 	.autoresume_en	 = BIT(3),
 };
 
+static const struct qusb2_phy_cfg msm8998_phy_cfg = {
+	.tbl            = msm8998_init_tbl,
+	.tbl_num        = ARRAY_SIZE(msm8998_init_tbl),
+	.regs           = msm8998_regs_layout,
+
+	.disable_ctrl   = POWER_DOWN,
+	.mask_core_ready = CORE_READY_STATUS,
+	.has_pll_override = true,
+	.autoresume_en   = BIT(0),
+	.update_tune1_with_efuse = true,
+};
+
 static const struct qusb2_phy_cfg sdm845_phy_cfg = {
 	.tbl		= sdm845_init_tbl,
 	.tbl_num	= ARRAY_SIZE(sdm845_init_tbl),
@@ -734,6 +771,9 @@ static const struct of_device_id qusb2_phy_of_match_table[] = {
 		.compatible	= "qcom,msm8996-qusb2-phy",
 		.data		= &msm8996_phy_cfg,
 	}, {
+		.compatible	= "qcom,msm8998-qusb2-phy",
+		.data		= &msm8998_phy_cfg,
+	}, {
 		.compatible	= "qcom,sdm845-qusb2-phy",
 		.data		= &sdm845_phy_cfg,
 	},
diff --git a/drivers/phy/qualcomm/phy-qcom-ufs-i.h b/drivers/phy/qualcomm/phy-qcom-ufs-i.h
index 681644e43248..f798fb64de94 100644
--- a/drivers/phy/qualcomm/phy-qcom-ufs-i.h
+++ b/drivers/phy/qualcomm/phy-qcom-ufs-i.h
@@ -23,24 +23,7 @@
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/delay.h>
-
-#define readl_poll_timeout(addr, val, cond, sleep_us, timeout_us) \
-({ \
-	ktime_t timeout = ktime_add_us(ktime_get(), timeout_us); \
-	might_sleep_if(timeout_us); \
-	for (;;) { \
-		(val) = readl(addr); \
-		if (cond) \
-			break; \
-		if (timeout_us && ktime_compare(ktime_get(), timeout) > 0) { \
-			(val) = readl(addr); \
-			break; \
-		} \
-		if (sleep_us) \
-			usleep_range(DIV_ROUND_UP(sleep_us, 4), sleep_us); \
-	} \
-	(cond) ? 0 : -ETIMEDOUT; \
-})
+#include <linux/iopoll.h>
 
 #define UFS_QCOM_PHY_CAL_ENTRY(reg, val)	\
 	{				\
diff --git a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
index 91fba60267a0..ba07121c3eff 100644
--- a/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
+++ b/drivers/phy/rockchip/phy-rockchip-inno-usb2.c
@@ -55,16 +55,16 @@ enum rockchip_usb2phy_host_state {
 };
 
 /**
- * Different states involved in USB charger detection.
- * USB_CHG_STATE_UNDEFINED	USB charger is not connected or detection
+ * enum usb_chg_state - Different states involved in USB charger detection.
+ * @USB_CHG_STATE_UNDEFINED:	USB charger is not connected or detection
  *				process is not yet started.
- * USB_CHG_STATE_WAIT_FOR_DCD	Waiting for Data pins contact.
- * USB_CHG_STATE_DCD_DONE	Data pin contact is detected.
- * USB_CHG_STATE_PRIMARY_DONE	Primary detection is completed (Detects
+ * @USB_CHG_STATE_WAIT_FOR_DCD:	Waiting for Data pins contact.
+ * @USB_CHG_STATE_DCD_DONE:	Data pin contact is detected.
+ * @USB_CHG_STATE_PRIMARY_DONE:	Primary detection is completed (Detects
  *				between SDP and DCP/CDP).
- * USB_CHG_STATE_SECONDARY_DONE	Secondary detection is completed (Detects
- *				between DCP and CDP).
- * USB_CHG_STATE_DETECTED	USB charger type is determined.
+ * @USB_CHG_STATE_SECONDARY_DONE: Secondary detection is completed (Detects
+ *				  between DCP and CDP).
+ * @USB_CHG_STATE_DETECTED:	USB charger type is determined.
  */
 enum usb_chg_state {
 	USB_CHG_STATE_UNDEFINED = 0,
@@ -94,7 +94,7 @@ struct usb2phy_reg {
 };
 
 /**
- * struct rockchip_chg_det_reg: usb charger detect registers
+ * struct rockchip_chg_det_reg - usb charger detect registers
  * @cp_det: charging port detected successfully.
  * @dcp_det: dedicated charging port detected successfully.
  * @dp_det: assert data pin connect successfully.
@@ -120,7 +120,7 @@ struct rockchip_chg_det_reg {
 };
 
 /**
- * struct rockchip_usb2phy_port_cfg: usb-phy port configuration.
+ * struct rockchip_usb2phy_port_cfg - usb-phy port configuration.
  * @phy_sus: phy suspend register.
  * @bvalid_det_en: vbus valid rise detection enable register.
  * @bvalid_det_st: vbus valid rise detection status register.
@@ -148,10 +148,11 @@ struct rockchip_usb2phy_port_cfg {
 };
 
 /**
- * struct rockchip_usb2phy_cfg: usb-phy configuration.
+ * struct rockchip_usb2phy_cfg - usb-phy configuration.
  * @reg: the address offset of grf for usb-phy config.
  * @num_ports: specify how many ports that the phy has.
  * @clkout_ctl: keep on/turn off output clk of phy.
+ * @port_cfgs: usb-phy port configurations.
  * @chg_det: charger detection registers.
  */
 struct rockchip_usb2phy_cfg {
@@ -163,12 +164,10 @@ struct rockchip_usb2phy_cfg {
 };
 
 /**
- * struct rockchip_usb2phy_port: usb-phy port data.
+ * struct rockchip_usb2phy_port - usb-phy port data.
+ * @phy: generic phy.
  * @port_id: flag for otg port or host port.
  * @suspended: phy suspended flag.
- * @utmi_avalid: utmi avalid status usage flag.
- *	true	- use avalid to get vbus status
- *	flase	- use bvalid to get vbus status
  * @vbus_attached: otg device vbus status.
  * @bvalid_irq: IRQ number assigned for vbus valid rise detection.
  * @ls_irq: IRQ number assigned for linestate detection.
@@ -178,7 +177,7 @@ struct rockchip_usb2phy_cfg {
  * @chg_work: charge detect work.
  * @otg_sm_work: OTG state machine work.
  * @sm_work: HOST state machine work.
- * @phy_cfg: port register configuration, assigned by driver data.
+ * @port_cfg: port register configuration, assigned by driver data.
  * @event_nb: hold event notification callback.
  * @state: define OTG enumeration states before device reset.
  * @mode: the dr_mode of the controller.
@@ -187,7 +186,6 @@ struct rockchip_usb2phy_port {
 	struct phy	*phy;
 	unsigned int	port_id;
 	bool		suspended;
-	bool		utmi_avalid;
 	bool		vbus_attached;
 	int		bvalid_irq;
 	int		ls_irq;
@@ -203,12 +201,13 @@ struct rockchip_usb2phy_port {
 };
 
 /**
- * struct rockchip_usb2phy: usb2.0 phy driver data.
+ * struct rockchip_usb2phy - usb2.0 phy driver data.
+ * @dev: pointer to device.
  * @grf: General Register Files regmap.
  * @usbgrf: USB General Register Files regmap.
  * @clk: clock struct of phy input clk.
  * @clk480m: clock struct of phy output clk.
- * @clk_hw: clock struct of phy output clk management.
+ * @clk480m_hw: clock struct of phy output clk management.
  * @chg_state: states involved in USB charger detection.
  * @chg_type: USB charger types.
  * @dcd_retries: The retry count used to track Data contact
@@ -542,12 +541,8 @@ static void rockchip_usb2phy_otg_sm_work(struct work_struct *work)
 	unsigned long delay;
 	bool vbus_attach, sch_work, notify_charger;
 
-	if (rport->utmi_avalid)
-		vbus_attach = property_enabled(rphy->grf,
-					       &rport->port_cfg->utmi_avalid);
-	else
-		vbus_attach = property_enabled(rphy->grf,
-					       &rport->port_cfg->utmi_bvalid);
+	vbus_attach = property_enabled(rphy->grf,
+				       &rport->port_cfg->utmi_bvalid);
 
 	sch_work = false;
 	notify_charger = false;
@@ -1021,9 +1016,6 @@ static int rockchip_usb2phy_otg_port_init(struct rockchip_usb2phy *rphy,
 	INIT_DELAYED_WORK(&rport->chg_work, rockchip_chg_detect_work);
 	INIT_DELAYED_WORK(&rport->otg_sm_work, rockchip_usb2phy_otg_sm_work);
 
-	rport->utmi_avalid =
-		of_property_read_bool(child_np, "rockchip,utmi-avalid");
-
 	/*
 	 * Some SoCs use one interrupt with otg-id/otg-bvalid/linestate
 	 * interrupts muxed together, so probe the otg-mux interrupt first,
diff --git a/drivers/phy/ti/Kconfig b/drivers/phy/ti/Kconfig
index c4709ed7fb0e..103efc456a12 100644
--- a/drivers/phy/ti/Kconfig
+++ b/drivers/phy/ti/Kconfig
@@ -33,12 +33,11 @@ config OMAP_CONTROL_PHY
 
 config OMAP_USB2
 	tristate "OMAP USB2 PHY Driver"
-	depends on ARCH_OMAP2PLUS
+	depends on ARCH_OMAP2PLUS || ARCH_K3
 	depends on USB_SUPPORT
 	select GENERIC_PHY
 	select USB_PHY
-	select OMAP_CONTROL_PHY
-	depends on OMAP_OCP2SCP
+	select OMAP_CONTROL_PHY if ARCH_OMAP2PLUS
 	help
 	  Enable this to support the transceiver that is part of SOC. This
 	  driver takes care of all the PHY functionality apart from comparator.
@@ -50,7 +49,6 @@ config TI_PIPE3
 	depends on ARCH_OMAP2PLUS || COMPILE_TEST
 	select GENERIC_PHY
 	select OMAP_CONTROL_PHY
-	depends on OMAP_OCP2SCP
 	help
 	  Enable this to support the PIPE3 PHY that is part of TI SOCs. This
 	  driver takes care of all the PHY functionality apart from comparator.
diff --git a/drivers/phy/ti/phy-omap-usb2.c b/drivers/phy/ti/phy-omap-usb2.c
index fe909fd8144f..e871f2983a0e 100644
--- a/drivers/phy/ti/phy-omap-usb2.c
+++ b/drivers/phy/ti/phy-omap-usb2.c
@@ -36,6 +36,10 @@
 #define USB2PHY_DISCON_BYP_LATCH (1 << 31)
 #define USB2PHY_ANA_CONFIG1 0x4c
 
+#define AM654_USB2_OTG_PD		BIT(8)
+#define AM654_USB2_VBUS_DET_EN		BIT(5)
+#define AM654_USB2_VBUSVALID_DET_EN	BIT(4)
+
 /**
  * omap_usb2_set_comparator - links the comparator present in the sytem with
  *	this phy
@@ -135,9 +139,9 @@ static int omap_usb_power_on(struct phy *x)
 
 static int omap_usb2_disable_clocks(struct omap_usb *phy)
 {
-	clk_disable(phy->wkupclk);
+	clk_disable_unprepare(phy->wkupclk);
 	if (!IS_ERR(phy->optclk))
-		clk_disable(phy->optclk);
+		clk_disable_unprepare(phy->optclk);
 
 	return 0;
 }
@@ -146,14 +150,14 @@ static int omap_usb2_enable_clocks(struct omap_usb *phy)
 {
 	int ret;
 
-	ret = clk_enable(phy->wkupclk);
+	ret = clk_prepare_enable(phy->wkupclk);
 	if (ret < 0) {
 		dev_err(phy->dev, "Failed to enable wkupclk %d\n", ret);
 		goto err0;
 	}
 
 	if (!IS_ERR(phy->optclk)) {
-		ret = clk_enable(phy->optclk);
+		ret = clk_prepare_enable(phy->optclk);
 		if (ret < 0) {
 			dev_err(phy->dev, "Failed to enable optclk %d\n", ret);
 			goto err1;
@@ -245,6 +249,15 @@ static const struct usb_phy_data am437x_usb2_data = {
 	.power_off = AM437X_USB2_PHY_PD | AM437X_USB2_OTG_PD,
 };
 
+static const struct usb_phy_data am654_usb2_data = {
+	.label = "am654_usb2",
+	.flags = OMAP_USB2_CALIBRATE_FALSE_DISCONNECT,
+	.mask = AM654_USB2_OTG_PD | AM654_USB2_VBUS_DET_EN |
+		AM654_USB2_VBUSVALID_DET_EN,
+	.power_on = AM654_USB2_VBUS_DET_EN | AM654_USB2_VBUSVALID_DET_EN,
+	.power_off = AM654_USB2_OTG_PD,
+};
+
 static const struct of_device_id omap_usb2_id_table[] = {
 	{
 		.compatible = "ti,omap-usb2",
@@ -266,6 +279,10 @@ static const struct of_device_id omap_usb2_id_table[] = {
 		.compatible = "ti,am437x-usb2",
 		.data = &am437x_usb2_data,
 	},
+	{
+		.compatible = "ti,am654-usb2",
+		.data = &am654_usb2_data,
+	},
 	{},
 };
 MODULE_DEVICE_TABLE(of, omap_usb2_id_table);
@@ -346,63 +363,72 @@ static int omap_usb2_probe(struct platform_device *pdev)
 		}
 	}
 
-	otg->set_host		= omap_usb_set_host;
-	otg->set_peripheral	= omap_usb_set_peripheral;
-	if (phy_data->flags & OMAP_USB2_HAS_SET_VBUS)
-		otg->set_vbus		= omap_usb_set_vbus;
-	if (phy_data->flags & OMAP_USB2_HAS_START_SRP)
-		otg->start_srp		= omap_usb_start_srp;
-	otg->usb_phy		= &phy->phy;
-
-	platform_set_drvdata(pdev, phy);
-	pm_runtime_enable(phy->dev);
-
-	generic_phy = devm_phy_create(phy->dev, NULL, &ops);
-	if (IS_ERR(generic_phy)) {
-		pm_runtime_disable(phy->dev);
-		return PTR_ERR(generic_phy);
-	}
-
-	phy_set_drvdata(generic_phy, phy);
-	omap_usb_power_off(generic_phy);
-
-	phy_provider = devm_of_phy_provider_register(phy->dev,
-			of_phy_simple_xlate);
-	if (IS_ERR(phy_provider)) {
-		pm_runtime_disable(phy->dev);
-		return PTR_ERR(phy_provider);
-	}
 
 	phy->wkupclk = devm_clk_get(phy->dev, "wkupclk");
 	if (IS_ERR(phy->wkupclk)) {
-		dev_warn(&pdev->dev, "unable to get wkupclk, trying old name\n");
+		if (PTR_ERR(phy->wkupclk) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+
+		dev_warn(&pdev->dev, "unable to get wkupclk %ld, trying old name\n",
+			 PTR_ERR(phy->wkupclk));
 		phy->wkupclk = devm_clk_get(phy->dev, "usb_phy_cm_clk32k");
+
 		if (IS_ERR(phy->wkupclk)) {
-			dev_err(&pdev->dev, "unable to get usb_phy_cm_clk32k\n");
-			pm_runtime_disable(phy->dev);
+			if (PTR_ERR(phy->wkupclk) != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "unable to get usb_phy_cm_clk32k\n");
 			return PTR_ERR(phy->wkupclk);
 		} else {
 			dev_warn(&pdev->dev,
 				 "found usb_phy_cm_clk32k, please fix DTS\n");
 		}
 	}
-	clk_prepare(phy->wkupclk);
 
 	phy->optclk = devm_clk_get(phy->dev, "refclk");
 	if (IS_ERR(phy->optclk)) {
+		if (PTR_ERR(phy->optclk) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+
 		dev_dbg(&pdev->dev, "unable to get refclk, trying old name\n");
 		phy->optclk = devm_clk_get(phy->dev, "usb_otg_ss_refclk960m");
+
 		if (IS_ERR(phy->optclk)) {
-			dev_dbg(&pdev->dev,
-				"unable to get usb_otg_ss_refclk960m\n");
+			if (PTR_ERR(phy->optclk) != -EPROBE_DEFER) {
+				dev_dbg(&pdev->dev,
+					"unable to get usb_otg_ss_refclk960m\n");
+			}
 		} else {
 			dev_warn(&pdev->dev,
 				 "found usb_otg_ss_refclk960m, please fix DTS\n");
 		}
 	}
 
-	if (!IS_ERR(phy->optclk))
-		clk_prepare(phy->optclk);
+	otg->set_host = omap_usb_set_host;
+	otg->set_peripheral = omap_usb_set_peripheral;
+	if (phy_data->flags & OMAP_USB2_HAS_SET_VBUS)
+		otg->set_vbus = omap_usb_set_vbus;
+	if (phy_data->flags & OMAP_USB2_HAS_START_SRP)
+		otg->start_srp = omap_usb_start_srp;
+	otg->usb_phy = &phy->phy;
+
+	platform_set_drvdata(pdev, phy);
+	pm_runtime_enable(phy->dev);
+
+	generic_phy = devm_phy_create(phy->dev, NULL, &ops);
+	if (IS_ERR(generic_phy)) {
+		pm_runtime_disable(phy->dev);
+		return PTR_ERR(generic_phy);
+	}
+
+	phy_set_drvdata(generic_phy, phy);
+	omap_usb_power_off(generic_phy);
+
+	phy_provider = devm_of_phy_provider_register(phy->dev,
+						     of_phy_simple_xlate);
+	if (IS_ERR(phy_provider)) {
+		pm_runtime_disable(phy->dev);
+		return PTR_ERR(phy_provider);
+	}
+
 
 	usb_add_phy_dev(&phy->phy);
 
@@ -413,9 +439,6 @@ static int omap_usb2_remove(struct platform_device *pdev)
 {
 	struct omap_usb	*phy = platform_get_drvdata(pdev);
 
-	clk_unprepare(phy->wkupclk);
-	if (!IS_ERR(phy->optclk))
-		clk_unprepare(phy->optclk);
 	usb_remove_phy(&phy->phy);
 	pm_runtime_disable(phy->dev);