Merge branch 'next' into for-linus

Prepare first round of input updates for 4.3 merge window.

16 files changed, 288 insertions, 54 deletions

diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig
index d4f0a817e858..dade381c7da8 100644
--- a/drivers/input/misc/Kconfig
+++ b/drivers/input/misc/Kconfig
@@ -259,7 +259,7 @@ config INPUT_APANEL
 config INPUT_GP2A
 	tristate "Sharp GP2AP002A00F I2C Proximity/Opto sensor driver"
 	depends on I2C
-	depends on GPIOLIB
+	depends on GPIOLIB || COMPILE_TEST
 	help
 	  Say Y here if you have a Sharp GP2AP002A00F proximity/als combo-chip
 	  hooked to an I2C bus.
@@ -269,7 +269,7 @@ config INPUT_GP2A
 
 config INPUT_GPIO_BEEPER
 	tristate "Generic GPIO Beeper support"
-	depends on GPIOLIB
+	depends on GPIOLIB || COMPILE_TEST
 	help
 	  Say Y here if you have a beeper connected to a GPIO pin.
 
@@ -278,7 +278,7 @@ config INPUT_GPIO_BEEPER
 
 config INPUT_GPIO_TILT_POLLED
 	tristate "Polled GPIO tilt switch"
-	depends on GPIOLIB
+	depends on GPIOLIB || COMPILE_TEST
 	select INPUT_POLLDEV
 	help
 	  This driver implements support for tilt switches connected
@@ -569,7 +569,7 @@ config INPUT_PWM_BEEPER
 
 config INPUT_GPIO_ROTARY_ENCODER
 	tristate "Rotary encoders connected to GPIO pins"
-	depends on GPIOLIB
+	depends on GPIOLIB || COMPILE_TEST
 	help
 	  Say Y here to add support for rotary encoders connected to GPIO lines.
 	  Check file:Documentation/input/rotary-encoder.txt for more
@@ -776,7 +776,8 @@ config INPUT_SOC_BUTTON_ARRAY
 
 config INPUT_DRV260X_HAPTICS
 	tristate "TI DRV260X haptics support"
-	depends on INPUT && I2C && GPIOLIB
+	depends on INPUT && I2C
+	depends on GPIOLIB || COMPILE_TEST
 	select INPUT_FF_MEMLESS
 	select REGMAP_I2C
 	help
diff --git a/drivers/input/misc/adxl34x-i2c.c b/drivers/input/misc/adxl34x-i2c.c
index bdb5d03b296e..a8b0a2eec344 100644
--- a/drivers/input/misc/adxl34x-i2c.c
+++ b/drivers/input/misc/adxl34x-i2c.c
@@ -158,7 +158,6 @@ MODULE_DEVICE_TABLE(of, adxl34x_of_id);
 static struct i2c_driver adxl34x_driver = {
 	.driver = {
 		.name = "adxl34x",
-		.owner = THIS_MODULE,
 		.pm = &adxl34x_i2c_pm,
 		.of_match_table = of_match_ptr(adxl34x_of_id),
 	},
diff --git a/drivers/input/misc/arizona-haptics.c b/drivers/input/misc/arizona-haptics.c
index 4dbbed74c9e4..4bf678541496 100644
--- a/drivers/input/misc/arizona-haptics.c
+++ b/drivers/input/misc/arizona-haptics.c
@@ -170,8 +170,8 @@ static int arizona_haptics_probe(struct platform_device *pdev)
 
 	INIT_WORK(&haptics->work, arizona_haptics_work);
 
-	haptics->input_dev = input_allocate_device();
-	if (haptics->input_dev == NULL) {
+	haptics->input_dev = devm_input_allocate_device(&pdev->dev);
+	if (!haptics->input_dev) {
 		dev_err(arizona->dev, "Failed to allocate input device\n");
 		return -ENOMEM;
 	}
@@ -188,41 +188,23 @@ static int arizona_haptics_probe(struct platform_device *pdev)
 	if (ret < 0) {
 		dev_err(arizona->dev, "input_ff_create_memless() failed: %d\n",
 			ret);
-		goto err_ialloc;
+		return ret;
 	}
 
 	ret = input_register_device(haptics->input_dev);
 	if (ret < 0) {
 		dev_err(arizona->dev, "couldn't register input device: %d\n",
 			ret);
-		goto err_iff;
+		return ret;
 	}
 
 	platform_set_drvdata(pdev, haptics);
 
 	return 0;
-
-err_iff:
-	if (haptics->input_dev)
-		input_ff_destroy(haptics->input_dev);
-err_ialloc:
-	input_free_device(haptics->input_dev);
-
-	return ret;
-}
-
-static int arizona_haptics_remove(struct platform_device *pdev)
-{
-	struct arizona_haptics *haptics = platform_get_drvdata(pdev);
-
-	input_unregister_device(haptics->input_dev);
-
-	return 0;
 }
 
 static struct platform_driver arizona_haptics_driver = {
 	.probe		= arizona_haptics_probe,
-	.remove		= arizona_haptics_remove,
 	.driver		= {
 		.name	= "arizona-haptics",
 	},
diff --git a/drivers/input/misc/ati_remote2.c b/drivers/input/misc/ati_remote2.c
index f63341f20b91..cfd58e87da26 100644
--- a/drivers/input/misc/ati_remote2.c
+++ b/drivers/input/misc/ati_remote2.c
@@ -94,7 +94,7 @@ static int ati_remote2_get_mode_mask(char *buffer,
 
 static unsigned int channel_mask = ATI_REMOTE2_MAX_CHANNEL_MASK;
 #define param_check_channel_mask(name, p) __param_check(name, p, unsigned int)
-static struct kernel_param_ops param_ops_channel_mask = {
+static const struct kernel_param_ops param_ops_channel_mask = {
 	.set = ati_remote2_set_channel_mask,
 	.get = ati_remote2_get_channel_mask,
 };
@@ -103,7 +103,7 @@ MODULE_PARM_DESC(channel_mask, "Bitmask of channels to accept <15:Channel16>...<
 
 static unsigned int mode_mask = ATI_REMOTE2_MAX_MODE_MASK;
 #define param_check_mode_mask(name, p) __param_check(name, p, unsigned int)
-static struct kernel_param_ops param_ops_mode_mask = {
+static const struct kernel_param_ops param_ops_mode_mask = {
 	.set = ati_remote2_set_mode_mask,
 	.get = ati_remote2_get_mode_mask,
 };
diff --git a/drivers/input/misc/bma150.c b/drivers/input/misc/bma150.c
index b36831c828d3..1d0e61d7c131 100644
--- a/drivers/input/misc/bma150.c
+++ b/drivers/input/misc/bma150.c
@@ -333,10 +333,9 @@ static void bma150_report_xyz(struct bma150_data *bma150)
 	y = ((0xc0 & data[2]) >> 6) | (data[3] << 2);
 	z = ((0xc0 & data[4]) >> 6) | (data[5] << 2);
 
-	/* sign extension */
-	x = (s16) (x << 6) >> 6;
-	y = (s16) (y << 6) >> 6;
-	z = (s16) (z << 6) >> 6;
+	x = sign_extend32(x, 9);
+	y = sign_extend32(y, 9);
+	z = sign_extend32(z, 9);
 
 	input_report_abs(bma150->input, ABS_X, x);
 	input_report_abs(bma150->input, ABS_Y, y);
@@ -654,7 +653,6 @@ MODULE_DEVICE_TABLE(i2c, bma150_id);
 
 static struct i2c_driver bma150_driver = {
 	.driver = {
-		.owner	= THIS_MODULE,
 		.name	= BMA150_DRIVER,
 		.pm	= &bma150_pm,
 	},
diff --git a/drivers/input/misc/cma3000_d0x_i2c.c b/drivers/input/misc/cma3000_d0x_i2c.c
index 4fdef98ceb56..c7021916b64b 100644
--- a/drivers/input/misc/cma3000_d0x_i2c.c
+++ b/drivers/input/misc/cma3000_d0x_i2c.c
@@ -118,7 +118,6 @@ static struct i2c_driver cma3000_i2c_driver = {
 	.id_table	= cma3000_i2c_id,
 	.driver = {
 		.name	= "cma3000_i2c_accl",
-		.owner	= THIS_MODULE,
 #ifdef CONFIG_PM
 		.pm	= &cma3000_i2c_pm_ops,
 #endif
diff --git a/drivers/input/misc/drv260x.c b/drivers/input/misc/drv260x.c
index e5d60ecd29a4..e65496e6463d 100644
--- a/drivers/input/misc/drv260x.c
+++ b/drivers/input/misc/drv260x.c
@@ -204,7 +204,7 @@ struct drv260x_data {
 	int overdrive_voltage;
 };
 
-static struct reg_default drv260x_reg_defs[] = {
+static const struct reg_default drv260x_reg_defs[] = {
 	{ DRV260X_STATUS, 0xe0 },
 	{ DRV260X_MODE, 0x40 },
 	{ DRV260X_RT_PB_IN, 0x00 },
@@ -720,7 +720,6 @@ static struct i2c_driver drv260x_driver = {
 	.probe		= drv260x_probe,
 	.driver		= {
 		.name	= "drv260x-haptics",
-		.owner	= THIS_MODULE,
 		.of_match_table = of_match_ptr(drv260x_of_match),
 		.pm	= &drv260x_pm_ops,
 	},
diff --git a/drivers/input/misc/drv2665.c b/drivers/input/misc/drv2665.c
index 0afaa33de07d..327a63c2f07d 100644
--- a/drivers/input/misc/drv2665.c
+++ b/drivers/input/misc/drv2665.c
@@ -74,7 +74,7 @@ static const u8 drv2665_sine_wave_form[] = {
 	0x9b, 0x9f, 0xa5, 0xad, 0xb8, 0xc4, 0xd2, 0xe0, 0xf0, 0x00,
 };
 
-static struct reg_default drv2665_reg_defs[] = {
+static const struct reg_default drv2665_reg_defs[] = {
 	{ DRV2665_STATUS, 0x02 },
 	{ DRV2665_CTRL_1, 0x28 },
 	{ DRV2665_CTRL_2, 0x40 },
@@ -309,7 +309,6 @@ static struct i2c_driver drv2665_driver = {
 	.probe		= drv2665_probe,
 	.driver		= {
 		.name	= "drv2665-haptics",
-		.owner	= THIS_MODULE,
 		.of_match_table = of_match_ptr(drv2665_of_match),
 		.pm	= &drv2665_pm_ops,
 	},
diff --git a/drivers/input/misc/drv2667.c b/drivers/input/misc/drv2667.c
index fc0fddf0896a..46a4be4e9dc3 100644
--- a/drivers/input/misc/drv2667.c
+++ b/drivers/input/misc/drv2667.c
@@ -116,7 +116,7 @@ struct drv2667_data {
 	u32 frequency;
 };
 
-static struct reg_default drv2667_reg_defs[] = {
+static const struct reg_default drv2667_reg_defs[] = {
 	{ DRV2667_STATUS, 0x02 },
 	{ DRV2667_CTRL_1, 0x28 },
 	{ DRV2667_CTRL_2, 0x40 },
@@ -484,7 +484,6 @@ static struct i2c_driver drv2667_driver = {
 	.probe		= drv2667_probe,
 	.driver		= {
 		.name	= "drv2667-haptics",
-		.owner	= THIS_MODULE,
 		.of_match_table = of_match_ptr(drv2667_of_match),
 		.pm	= &drv2667_pm_ops,
 	},
diff --git a/drivers/input/misc/gp2ap002a00f.c b/drivers/input/misc/gp2ap002a00f.c
index 0ac176d66a6f..3bfdfcc20485 100644
--- a/drivers/input/misc/gp2ap002a00f.c
+++ b/drivers/input/misc/gp2ap002a00f.c
@@ -267,11 +267,11 @@ static const struct i2c_device_id gp2a_i2c_id[] = {
 	{ GP2A_I2C_NAME, 0 },
 	{ }
 };
+MODULE_DEVICE_TABLE(i2c, gp2a_i2c_id);
 
 static struct i2c_driver gp2a_i2c_driver = {
 	.driver = {
 		.name	= GP2A_I2C_NAME,
-		.owner	= THIS_MODULE,
 		.pm	= &gp2a_pm,
 	},
 	.probe		= gp2a_probe,
diff --git a/drivers/input/misc/kxtj9.c b/drivers/input/misc/kxtj9.c
index 6e29349da537..e058d711256a 100644
--- a/drivers/input/misc/kxtj9.c
+++ b/drivers/input/misc/kxtj9.c
@@ -658,7 +658,6 @@ MODULE_DEVICE_TABLE(i2c, kxtj9_id);
 static struct i2c_driver kxtj9_driver = {
 	.driver = {
 		.name	= NAME,
-		.owner	= THIS_MODULE,
 		.pm	= &kxtj9_pm_ops,
 	},
 	.probe		= kxtj9_probe,
diff --git a/drivers/input/misc/max8997_haptic.c b/drivers/input/misc/max8997_haptic.c
index d0f687281339..a806ba3818f7 100644
--- a/drivers/input/misc/max8997_haptic.c
+++ b/drivers/input/misc/max8997_haptic.c
@@ -394,7 +394,7 @@ static const struct platform_device_id max8997_haptic_id[] = {
 	{ "max8997-haptic", 0 },
 	{ },
 };
-MODULE_DEVICE_TABLE(i2c, max8997_haptic_id);
+MODULE_DEVICE_TABLE(platform, max8997_haptic_id);
 
 static struct platform_driver max8997_haptic_driver = {
 	.driver	= {
@@ -407,7 +407,6 @@ static struct platform_driver max8997_haptic_driver = {
 };
 module_platform_driver(max8997_haptic_driver);
 
-MODULE_ALIAS("platform:max8997-haptic");
 MODULE_AUTHOR("Donggeun Kim <dg77.kim@samsung.com>");
 MODULE_DESCRIPTION("max8997_haptic driver");
 MODULE_LICENSE("GPL");
diff --git a/drivers/input/misc/mpu3050.c b/drivers/input/misc/mpu3050.c
index 5e5051351c3a..f088db31cfc7 100644
--- a/drivers/input/misc/mpu3050.c
+++ b/drivers/input/misc/mpu3050.c
@@ -466,7 +466,6 @@ MODULE_DEVICE_TABLE(of, mpu3050_of_match);
 static struct i2c_driver mpu3050_i2c_driver = {
 	.driver	= {
 		.name	= "mpu3050",
-		.owner	= THIS_MODULE,
 		.pm	= &mpu3050_pm,
 		.of_match_table = mpu3050_of_match,
 	},
diff --git a/drivers/input/misc/pcf8574_keypad.c b/drivers/input/misc/pcf8574_keypad.c
index 97f711a7bd20..4abdf1efb3e0 100644
--- a/drivers/input/misc/pcf8574_keypad.c
+++ b/drivers/input/misc/pcf8574_keypad.c
@@ -208,7 +208,6 @@ MODULE_DEVICE_TABLE(i2c, pcf8574_kp_id);
 static struct i2c_driver pcf8574_kp_driver = {
 	.driver = {
 		.name  = DRV_NAME,
-		.owner = THIS_MODULE,
 #ifdef CONFIG_PM
 		.pm = &pcf8574_kp_pm_ops,
 #endif
diff --git a/drivers/input/misc/pmic8xxx-pwrkey.c b/drivers/input/misc/pmic8xxx-pwrkey.c
index c4ca20e63221..3f02e0e03d12 100644
--- a/drivers/input/misc/pmic8xxx-pwrkey.c
+++ b/drivers/input/misc/pmic8xxx-pwrkey.c
@@ -20,17 +20,72 @@
 #include <linux/regmap.h>
 #include <linux/log2.h>
 #include <linux/of.h>
+#include <linux/of_device.h>
 
 #define PON_CNTL_1 0x1C
 #define PON_CNTL_PULL_UP BIT(7)
 #define PON_CNTL_TRIG_DELAY_MASK (0x7)
+#define PON_CNTL_1_PULL_UP_EN			0xe0
+#define PON_CNTL_1_USB_PWR_EN			0x10
+#define PON_CNTL_1_WD_EN_RESET			0x08
+
+#define PM8058_SLEEP_CTRL			0x02b
+#define PM8921_SLEEP_CTRL			0x10a
+
+#define SLEEP_CTRL_SMPL_EN_RESET		0x04
+
+/* Regulator master enable addresses */
+#define REG_PM8058_VREG_EN_MSM			0x018
+#define REG_PM8058_VREG_EN_GRP_5_4		0x1c8
+
+/* Regulator control registers for shutdown/reset */
+#define PM8058_S0_CTRL				0x004
+#define PM8058_S1_CTRL				0x005
+#define PM8058_S3_CTRL				0x111
+#define PM8058_L21_CTRL				0x120
+#define PM8058_L22_CTRL				0x121
+
+#define PM8058_REGULATOR_ENABLE_MASK		0x80
+#define PM8058_REGULATOR_ENABLE			0x80
+#define PM8058_REGULATOR_DISABLE		0x00
+#define PM8058_REGULATOR_PULL_DOWN_MASK		0x40
+#define PM8058_REGULATOR_PULL_DOWN_EN		0x40
+
+/* Buck CTRL register */
+#define PM8058_SMPS_LEGACY_VREF_SEL		0x20
+#define PM8058_SMPS_LEGACY_VPROG_MASK		0x1f
+#define PM8058_SMPS_ADVANCED_BAND_MASK		0xC0
+#define PM8058_SMPS_ADVANCED_BAND_SHIFT		6
+#define PM8058_SMPS_ADVANCED_VPROG_MASK		0x3f
+
+/* Buck TEST2 registers for shutdown/reset */
+#define PM8058_S0_TEST2				0x084
+#define PM8058_S1_TEST2				0x085
+#define PM8058_S3_TEST2				0x11a
+
+#define PM8058_REGULATOR_BANK_WRITE		0x80
+#define PM8058_REGULATOR_BANK_MASK		0x70
+#define PM8058_REGULATOR_BANK_SHIFT		4
+#define PM8058_REGULATOR_BANK_SEL(n)	((n) << PM8058_REGULATOR_BANK_SHIFT)
+
+/* Buck TEST2 register bank 1 */
+#define PM8058_SMPS_LEGACY_VLOW_SEL		0x01
+
+/* Buck TEST2 register bank 7 */
+#define PM8058_SMPS_ADVANCED_MODE_MASK		0x02
+#define PM8058_SMPS_ADVANCED_MODE		0x02
+#define PM8058_SMPS_LEGACY_MODE			0x00
 
 /**
  * struct pmic8xxx_pwrkey - pmic8xxx pwrkey information
  * @key_press_irq: key press irq number
+ * @regmap: device regmap
+ * @shutdown_fn: shutdown configuration function
  */
 struct pmic8xxx_pwrkey {
 	int key_press_irq;
+	struct regmap *regmap;
+	int (*shutdown_fn)(struct pmic8xxx_pwrkey *, bool);
 };
 
 static irqreturn_t pwrkey_press_irq(int irq, void *_pwr)
@@ -76,6 +131,212 @@ static int __maybe_unused pmic8xxx_pwrkey_resume(struct device *dev)
 static SIMPLE_DEV_PM_OPS(pm8xxx_pwr_key_pm_ops,
 		pmic8xxx_pwrkey_suspend, pmic8xxx_pwrkey_resume);
 
+static void pmic8xxx_pwrkey_shutdown(struct platform_device *pdev)
+{
+	struct pmic8xxx_pwrkey *pwrkey = platform_get_drvdata(pdev);
+	int error;
+	u8 mask, val;
+	bool reset = system_state == SYSTEM_RESTART;
+
+	if (pwrkey->shutdown_fn) {
+		error = pwrkey->shutdown_fn(pwrkey, reset);
+		if (error)
+			return;
+	}
+
+	/*
+	 * Select action to perform (reset or shutdown) when PS_HOLD goes low.
+	 * Also ensure that KPD, CBL0, and CBL1 pull ups are enabled and that
+	 * USB charging is enabled.
+	 */
+	mask = PON_CNTL_1_PULL_UP_EN | PON_CNTL_1_USB_PWR_EN;
+	mask |= PON_CNTL_1_WD_EN_RESET;
+	val = mask;
+	if (!reset)
+		val &= ~PON_CNTL_1_WD_EN_RESET;
+
+	regmap_update_bits(pwrkey->regmap, PON_CNTL_1, mask, val);
+}
+
+/*
+ * Set an SMPS regulator to be disabled in its CTRL register, but enabled
+ * in the master enable register.  Also set it's pull down enable bit.
+ * Take care to make sure that the output voltage doesn't change if switching
+ * from advanced mode to legacy mode.
+ */
+static int pm8058_disable_smps_locally_set_pull_down(struct regmap *regmap,
+	u16 ctrl_addr, u16 test2_addr, u16 master_enable_addr,
+	u8 master_enable_bit)
+{
+	int error;
+	u8 vref_sel, vlow_sel, band, vprog, bank;
+	unsigned int reg;
+
+	bank = PM8058_REGULATOR_BANK_SEL(7);
+	error = regmap_write(regmap, test2_addr, bank);
+	if (error)
+		return error;
+
+	error = regmap_read(regmap, test2_addr, &reg);
+	if (error)
+		return error;
+
+	reg &= PM8058_SMPS_ADVANCED_MODE_MASK;
+	/* Check if in advanced mode. */
+	if (reg == PM8058_SMPS_ADVANCED_MODE) {
+		/* Determine current output voltage. */
+		error = regmap_read(regmap, ctrl_addr, &reg);
+		if (error)
+			return error;
+
+		band = reg & PM8058_SMPS_ADVANCED_BAND_MASK;
+		band >>= PM8058_SMPS_ADVANCED_BAND_SHIFT;
+		switch (band) {
+		case 3:
+			vref_sel = 0;
+			vlow_sel = 0;
+			break;
+		case 2:
+			vref_sel = PM8058_SMPS_LEGACY_VREF_SEL;
+			vlow_sel = 0;
+			break;
+		case 1:
+			vref_sel = PM8058_SMPS_LEGACY_VREF_SEL;
+			vlow_sel = PM8058_SMPS_LEGACY_VLOW_SEL;
+			break;
+		default:
+			pr_err("%s: regulator already disabled\n", __func__);
+			return -EPERM;
+		}
+		vprog = reg & PM8058_SMPS_ADVANCED_VPROG_MASK;
+		/* Round up if fine step is in use. */
+		vprog = (vprog + 1) >> 1;
+		if (vprog > PM8058_SMPS_LEGACY_VPROG_MASK)
+			vprog = PM8058_SMPS_LEGACY_VPROG_MASK;
+
+		/* Set VLOW_SEL bit. */
+		bank = PM8058_REGULATOR_BANK_SEL(1);
+		error = regmap_write(regmap, test2_addr, bank);
+		if (error)
+			return error;
+
+		error = regmap_update_bits(regmap, test2_addr,
+			PM8058_REGULATOR_BANK_WRITE | PM8058_REGULATOR_BANK_MASK
+				| PM8058_SMPS_LEGACY_VLOW_SEL,
+			PM8058_REGULATOR_BANK_WRITE |
+			PM8058_REGULATOR_BANK_SEL(1) | vlow_sel);
+		if (error)
+			return error;
+
+		/* Switch to legacy mode */
+		bank = PM8058_REGULATOR_BANK_SEL(7);
+		error = regmap_write(regmap, test2_addr, bank);
+		if (error)
+			return error;
+
+		error = regmap_update_bits(regmap, test2_addr,
+				PM8058_REGULATOR_BANK_WRITE |
+				PM8058_REGULATOR_BANK_MASK |
+				PM8058_SMPS_ADVANCED_MODE_MASK,
+				PM8058_REGULATOR_BANK_WRITE |
+				PM8058_REGULATOR_BANK_SEL(7) |
+				PM8058_SMPS_LEGACY_MODE);
+		if (error)
+			return error;
+
+		/* Enable locally, enable pull down, keep voltage the same. */
+		error = regmap_update_bits(regmap, ctrl_addr,
+			PM8058_REGULATOR_ENABLE_MASK |
+			PM8058_REGULATOR_PULL_DOWN_MASK |
+			PM8058_SMPS_LEGACY_VREF_SEL |
+			PM8058_SMPS_LEGACY_VPROG_MASK,
+			PM8058_REGULATOR_ENABLE | PM8058_REGULATOR_PULL_DOWN_EN
+				| vref_sel | vprog);
+		if (error)
+			return error;
+	}
+
+	/* Enable in master control register. */
+	error = regmap_update_bits(regmap, master_enable_addr,
+			master_enable_bit, master_enable_bit);
+	if (error)
+		return error;
+
+	/* Disable locally and enable pull down. */
+	return regmap_update_bits(regmap, ctrl_addr,
+		PM8058_REGULATOR_ENABLE_MASK | PM8058_REGULATOR_PULL_DOWN_MASK,
+		PM8058_REGULATOR_DISABLE | PM8058_REGULATOR_PULL_DOWN_EN);
+}
+
+static int pm8058_disable_ldo_locally_set_pull_down(struct regmap *regmap,
+		u16 ctrl_addr, u16 master_enable_addr, u8 master_enable_bit)
+{
+	int error;
+
+	/* Enable LDO in master control register. */
+	error = regmap_update_bits(regmap, master_enable_addr,
+			master_enable_bit, master_enable_bit);
+	if (error)
+		return error;
+
+	/* Disable LDO in CTRL register and set pull down */
+	return regmap_update_bits(regmap, ctrl_addr,
+		PM8058_REGULATOR_ENABLE_MASK | PM8058_REGULATOR_PULL_DOWN_MASK,
+		PM8058_REGULATOR_DISABLE | PM8058_REGULATOR_PULL_DOWN_EN);
+}
+
+static int pm8058_pwrkey_shutdown(struct pmic8xxx_pwrkey *pwrkey, bool reset)
+{
+	int error;
+	struct regmap *regmap = pwrkey->regmap;
+	u8 mask, val;
+
+	/* When shutting down, enable active pulldowns on important rails. */
+	if (!reset) {
+		/* Disable SMPS's 0,1,3 locally and set pulldown enable bits. */
+		pm8058_disable_smps_locally_set_pull_down(regmap,
+			PM8058_S0_CTRL, PM8058_S0_TEST2,
+			REG_PM8058_VREG_EN_MSM, BIT(7));
+		pm8058_disable_smps_locally_set_pull_down(regmap,
+			PM8058_S1_CTRL, PM8058_S1_TEST2,
+			REG_PM8058_VREG_EN_MSM, BIT(6));
+		pm8058_disable_smps_locally_set_pull_down(regmap,
+			PM8058_S3_CTRL, PM8058_S3_TEST2,
+			REG_PM8058_VREG_EN_GRP_5_4, BIT(7) | BIT(4));
+		/* Disable LDO 21 locally and set pulldown enable bit. */
+		pm8058_disable_ldo_locally_set_pull_down(regmap,
+			PM8058_L21_CTRL, REG_PM8058_VREG_EN_GRP_5_4,
+			BIT(1));
+	}
+
+	/*
+	 * Fix-up: Set regulator LDO22 to 1.225 V in high power mode. Leave its
+	 * pull-down state intact. This ensures a safe shutdown.
+	 */
+	error = regmap_update_bits(regmap, PM8058_L22_CTRL, 0xbf, 0x93);
+	if (error)
+		return error;
+
+	/* Enable SMPL if resetting is desired */
+	mask = SLEEP_CTRL_SMPL_EN_RESET;
+	val = 0;
+	if (reset)
+		val = mask;
+	return regmap_update_bits(regmap, PM8058_SLEEP_CTRL, mask, val);
+}
+
+static int pm8921_pwrkey_shutdown(struct pmic8xxx_pwrkey *pwrkey, bool reset)
+{
+	struct regmap *regmap = pwrkey->regmap;
+	u8 mask = SLEEP_CTRL_SMPL_EN_RESET;
+	u8 val = 0;
+
+	/* Enable SMPL if resetting is desired */
+	if (reset)
+		val = mask;
+	return regmap_update_bits(regmap, PM8921_SLEEP_CTRL, mask, val);
+}
+
 static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
 {
 	struct input_dev *pwr;
@@ -109,6 +370,8 @@ static int pmic8xxx_pwrkey_probe(struct platform_device *pdev)
 	if (!pwrkey)
 		return -ENOMEM;
 
+	pwrkey->shutdown_fn = of_device_get_match_data(&pdev->dev);
+	pwrkey->regmap = regmap;
 	pwrkey->key_press_irq = key_press_irq;
 
 	pwr = devm_input_allocate_device(&pdev->dev);
@@ -182,8 +445,8 @@ static int pmic8xxx_pwrkey_remove(struct platform_device *pdev)
 }
 
 static const struct of_device_id pm8xxx_pwr_key_id_table[] = {
-	{ .compatible = "qcom,pm8058-pwrkey" },
-	{ .compatible = "qcom,pm8921-pwrkey" },
+	{ .compatible = "qcom,pm8058-pwrkey", .data = &pm8058_pwrkey_shutdown },
+	{ .compatible = "qcom,pm8921-pwrkey", .data = &pm8921_pwrkey_shutdown },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, pm8xxx_pwr_key_id_table);
@@ -191,6 +454,7 @@ MODULE_DEVICE_TABLE(of, pm8xxx_pwr_key_id_table);
 static struct platform_driver pmic8xxx_pwrkey_driver = {
 	.probe		= pmic8xxx_pwrkey_probe,
 	.remove		= pmic8xxx_pwrkey_remove,
+	.shutdown	= pmic8xxx_pwrkey_shutdown,
 	.driver		= {
 		.name	= "pm8xxx-pwrkey",
 		.pm	= &pm8xxx_pwr_key_pm_ops,
diff --git a/drivers/input/misc/uinput.c b/drivers/input/misc/uinput.c
index 421e29e4cd81..345df9b03aed 100644
--- a/drivers/input/misc/uinput.c
+++ b/drivers/input/misc/uinput.c
@@ -320,10 +320,8 @@ static int uinput_validate_absbits(struct input_dev *dev)
 	 * Check if absmin/absmax/absfuzz/absflat are sane.
 	 */
 
-	for (cnt = 0; cnt < ABS_CNT; cnt++) {
+	for_each_set_bit(cnt, dev->absbit, ABS_CNT) {
 		int min, max;
-		if (!test_bit(cnt, dev->absbit))
-			continue;
 
 		min = input_abs_get_min(dev, cnt);
 		max = input_abs_get_max(dev, cnt);
@@ -416,7 +414,7 @@ static int uinput_setup_device(struct uinput_device *udev,
 	dev->id.product	= user_dev->id.product;
 	dev->id.version	= user_dev->id.version;
 
-	for (i = 0; i < ABS_CNT; i++) {
+	for_each_set_bit(i, dev->absbit, ABS_CNT) {
 		input_abs_set_max(dev, i, user_dev->absmax[i]);
 		input_abs_set_min(dev, i, user_dev->absmin[i]);
 		input_abs_set_fuzz(dev, i, user_dev->absfuzz[i]);