Merge tag 'iio-for-4.7b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-testing

Jonathan writes:

2nd set of new device support, features and cleanup for IIO in the 4.7 cycle.

Bit of a bumper set for new drivers but plenty of other stuff here as well!

New device support
* ad5592R ADC/DAC
  - new driver supporting ad5592r and ad5593r combined ADC/DAC and gpio chips.
* Aosong am2315 relative humidity
  - new driver with triggered buffer support in follow up patch.
* bmi160 imu
  - new driver
* bmp280
  - bmp180 support - note there is support in the misc/bmp085 driver. Intent
    is to remove that driver long term.
* invensense mpu6050
  - cleanup leading to explicit support of mpu9150 with a good few cleanups
    along the way.
* Hope RF hp03 pressure and temperature sensor.
  - new driver
* maxim DS1803 potentiometer
  - new driver
* maxim max44000 light and proximity sensor
  - new driver built in a series of steps to support pretty much everything.
* ROHM BH1780 light sensor
  - new driver. There is an existing driver in misc that this is pretty much
    intended to replace.  The discussion on whether to support the non standard
    interface of that driver is some way is continuing.
* st-gyro
  - lsm9ds0-gyro.  The accel/magn side of this will take a while longer as
    extensions to the st library are needed for cases where two types of sensor
    share a single i2c address.
* ti-adc081c
  - support the adc101c and adc121c
* Vishay VEML6070 UV sensor
  - new driver.

New features
* core
  - devm_ APIs for channel_get and channel_get_all.  The first user of these
    is the generic ADC based thermal driver.  As it is going through the
    thermal tree these will be picked up as a patch to that next cycle as that
    is how the author preferred to do it.
  - mounting matrix support.  This new core support allows devices to provide
    to userspace (typically from the device tree) allowing compensation for how
    the sensor is mounted on the device.  First examples are on UAVs but it
    has a more mundane use on typical phone where the chip may be on the front
    or the back of the circuit board and soldered at any angle. Includes
    support for this ABI in ak8975 (which has an older interface, now
    deprecated) and mpu6050.
* tools
  - add a -a option to enable all available channels in generic_buffer sample.
    Makes it somewhat easier to use.
* adis library and drivers
  - support manual self test flag clearing.  This has technically been broken
    for a very long time - result is an offset on readings as the applied field
    is on all the time.
* ak8975
  - triggered buffer support
* bmc150
  - spi support (including splitting the driver into core and i2c parts)
* bmp280
  - oversampling support.
* dht11
  - improved logging - useful to debug timing issues on this quirky device.
* st-sensors
  - read each channel invidivually as not all support the optimization of
  reading in bulk.  This is technically a fix, but will need to be backported
  if desired.
  - support open drain and shared interrupts.
* ti-adc081c
  - triggered buffer support.

Cleanups
* inkern
  - white space fix.
* ad7606
  - use the iio_device_claim_direct_mode call rather than open coding equiv.
* ad799x
  - white space fix.
* ad9523
  - unsigned -> unsigned int
* apds9660
  - brace location tidying up.
  - silence an uninitialized variable warning.
* ak8975
  - else and brace on same line fix.
* at91_adc
  - white space fixes.
* bmc150
  - use regmap stored copy of the device pointer rather than having an
    additional copy.
* bmg160
  - use regmap stored copy of the device pointer rather than having an
    additional copy.
* hid-sensors
  - white space fixes.
* mcp3422
  - white space fix.
* mma7455
  - use regmap to retrieve the device struct rather than carrying another copy
    in the private data.
* ms_sensors
  - white space fix.
* mxs-lradc
  - move current bindings out of staging - some will be shortly deprecated but
    the reality is that we have device trees out there using them so they will
    need to be supported for some time.  They accidentally got left behind
    when the driver graduated from staging.
  - white space cleanup.
  - set INPUT_PROP_DIRECT.
  - move ts config into a better function.
  - move the STMP reset out of the ADC init.
* vf610_adc
  - case label indenting fix.

14 files changed, 890 insertions, 21 deletions

diff --git a/drivers/iio/imu/Kconfig b/drivers/iio/imu/Kconfig
index 5e610f7de5aa..1f1ad41ef881 100644
--- a/drivers/iio/imu/Kconfig
+++ b/drivers/iio/imu/Kconfig
@@ -25,6 +25,8 @@ config ADIS16480
 	  Say yes here to build support for Analog Devices ADIS16375, ADIS16480,
 	  ADIS16485, ADIS16488 inertial sensors.
 
+source "drivers/iio/imu/bmi160/Kconfig"
+
 config KMX61
 	tristate "Kionix KMX61 6-axis accelerometer and magnetometer"
 	depends on I2C
diff --git a/drivers/iio/imu/Makefile b/drivers/iio/imu/Makefile
index e1e6e3d70e26..c71bcd30dc38 100644
--- a/drivers/iio/imu/Makefile
+++ b/drivers/iio/imu/Makefile
@@ -13,6 +13,7 @@ adis_lib-$(CONFIG_IIO_ADIS_LIB_BUFFER) += adis_trigger.o
 adis_lib-$(CONFIG_IIO_ADIS_LIB_BUFFER) += adis_buffer.o
 obj-$(CONFIG_IIO_ADIS_LIB) += adis_lib.o
 
+obj-y += bmi160/
 obj-y += inv_mpu6050/
 
 obj-$(CONFIG_KMX61) += kmx61.o
diff --git a/drivers/iio/imu/adis.c b/drivers/iio/imu/adis.c
index 911255d41c1a..ad6f91d06185 100644
--- a/drivers/iio/imu/adis.c
+++ b/drivers/iio/imu/adis.c
@@ -324,7 +324,12 @@ static int adis_self_test(struct adis *adis)
 
 	msleep(adis->data->startup_delay);
 
-	return adis_check_status(adis);
+	ret = adis_check_status(adis);
+
+	if (adis->data->self_test_no_autoclear)
+		adis_write_reg_16(adis, adis->data->msc_ctrl_reg, 0x00);
+
+	return ret;
 }
 
 /**
diff --git a/drivers/iio/imu/bmi160/Kconfig b/drivers/iio/imu/bmi160/Kconfig
new file mode 100644
index 000000000000..005c17ccc2b0
--- /dev/null
+++ b/drivers/iio/imu/bmi160/Kconfig
@@ -0,0 +1,32 @@
+#
+# BMI160 IMU driver
+#
+
+config BMI160
+	tristate
+	select IIO_BUFFER
+	select IIO_TRIGGERED_BUFFER
+
+config BMI160_I2C
+	tristate "Bosch BMI160 I2C driver"
+	depends on I2C
+	select BMI160
+	select REGMAP_I2C
+	help
+	  If you say yes here you get support for BMI160 IMU on I2C with
+	  accelerometer, gyroscope and external BMG160 magnetometer.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called bmi160_i2c.
+
+config BMI160_SPI
+	tristate "Bosch BMI160 SPI driver"
+	depends on SPI
+	select BMI160
+	select REGMAP_SPI
+	help
+	  If you say yes here you get support for BMI160 IMU on SPI with
+	  accelerometer, gyroscope and external BMG160 magnetometer.
+
+	  This driver can also be built as a module. If so, the module will be
+	  called bmi160_spi.
diff --git a/drivers/iio/imu/bmi160/Makefile b/drivers/iio/imu/bmi160/Makefile
new file mode 100644
index 000000000000..10365e493ae2
--- /dev/null
+++ b/drivers/iio/imu/bmi160/Makefile
@@ -0,0 +1,6 @@
+#
+# Makefile for Bosch BMI160 IMU
+#
+obj-$(CONFIG_BMI160) += bmi160_core.o
+obj-$(CONFIG_BMI160_I2C) += bmi160_i2c.o
+obj-$(CONFIG_BMI160_SPI) += bmi160_spi.o
diff --git a/drivers/iio/imu/bmi160/bmi160.h b/drivers/iio/imu/bmi160/bmi160.h
new file mode 100644
index 000000000000..d2ae6ed70271
--- /dev/null
+++ b/drivers/iio/imu/bmi160/bmi160.h
@@ -0,0 +1,10 @@
+#ifndef BMI160_H_
+#define BMI160_H_
+
+extern const struct regmap_config bmi160_regmap_config;
+
+int bmi160_core_probe(struct device *dev, struct regmap *regmap,
+		      const char *name, bool use_spi);
+void bmi160_core_remove(struct device *dev);
+
+#endif  /* BMI160_H_ */
diff --git a/drivers/iio/imu/bmi160/bmi160_core.c b/drivers/iio/imu/bmi160/bmi160_core.c
new file mode 100644
index 000000000000..0bf92b06d7d8
--- /dev/null
+++ b/drivers/iio/imu/bmi160/bmi160_core.c
@@ -0,0 +1,596 @@
+/*
+ * BMI160 - Bosch IMU (accel, gyro plus external magnetometer)
+ *
+ * Copyright (c) 2016, Intel Corporation.
+ *
+ * This file is subject to the terms and conditions of version 2 of
+ * the GNU General Public License.  See the file COPYING in the main
+ * directory of this archive for more details.
+ *
+ * IIO core driver for BMI160, with support for I2C/SPI busses
+ *
+ * TODO: magnetometer, interrupts, hardware FIFO
+ */
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/acpi.h>
+#include <linux/delay.h>
+
+#include <linux/iio/iio.h>
+#include <linux/iio/triggered_buffer.h>
+#include <linux/iio/trigger_consumer.h>
+#include <linux/iio/buffer.h>
+
+#include "bmi160.h"
+
+#define BMI160_REG_CHIP_ID	0x00
+#define BMI160_CHIP_ID_VAL	0xD1
+
+#define BMI160_REG_PMU_STATUS	0x03
+
+/* X axis data low byte address, the rest can be obtained using axis offset */
+#define BMI160_REG_DATA_MAGN_XOUT_L	0x04
+#define BMI160_REG_DATA_GYRO_XOUT_L	0x0C
+#define BMI160_REG_DATA_ACCEL_XOUT_L	0x12
+
+#define BMI160_REG_ACCEL_CONFIG		0x40
+#define BMI160_ACCEL_CONFIG_ODR_MASK	GENMASK(3, 0)
+#define BMI160_ACCEL_CONFIG_BWP_MASK	GENMASK(6, 4)
+
+#define BMI160_REG_ACCEL_RANGE		0x41
+#define BMI160_ACCEL_RANGE_2G		0x03
+#define BMI160_ACCEL_RANGE_4G		0x05
+#define BMI160_ACCEL_RANGE_8G		0x08
+#define BMI160_ACCEL_RANGE_16G		0x0C
+
+#define BMI160_REG_GYRO_CONFIG		0x42
+#define BMI160_GYRO_CONFIG_ODR_MASK	GENMASK(3, 0)
+#define BMI160_GYRO_CONFIG_BWP_MASK	GENMASK(5, 4)
+
+#define BMI160_REG_GYRO_RANGE		0x43
+#define BMI160_GYRO_RANGE_2000DPS	0x00
+#define BMI160_GYRO_RANGE_1000DPS	0x01
+#define BMI160_GYRO_RANGE_500DPS	0x02
+#define BMI160_GYRO_RANGE_250DPS	0x03
+#define BMI160_GYRO_RANGE_125DPS	0x04
+
+#define BMI160_REG_CMD			0x7E
+#define BMI160_CMD_ACCEL_PM_SUSPEND	0x10
+#define BMI160_CMD_ACCEL_PM_NORMAL	0x11
+#define BMI160_CMD_ACCEL_PM_LOW_POWER	0x12
+#define BMI160_CMD_GYRO_PM_SUSPEND	0x14
+#define BMI160_CMD_GYRO_PM_NORMAL	0x15
+#define BMI160_CMD_GYRO_PM_FAST_STARTUP	0x17
+#define BMI160_CMD_SOFTRESET		0xB6
+
+#define BMI160_REG_DUMMY		0x7F
+
+#define BMI160_ACCEL_PMU_MIN_USLEEP	3200
+#define BMI160_ACCEL_PMU_MAX_USLEEP	3800
+#define BMI160_GYRO_PMU_MIN_USLEEP	55000
+#define BMI160_GYRO_PMU_MAX_USLEEP	80000
+#define BMI160_SOFTRESET_USLEEP		1000
+
+#define BMI160_CHANNEL(_type, _axis, _index) {			\
+	.type = _type,						\
+	.modified = 1,						\
+	.channel2 = IIO_MOD_##_axis,				\
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
+	.info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE) |  \
+		BIT(IIO_CHAN_INFO_SAMP_FREQ),			\
+	.scan_index = _index,					\
+	.scan_type = {						\
+		.sign = 's',					\
+		.realbits = 16,					\
+		.storagebits = 16,				\
+		.endianness = IIO_LE,				\
+	},							\
+}
+
+/* scan indexes follow DATA register order */
+enum bmi160_scan_axis {
+	BMI160_SCAN_EXT_MAGN_X = 0,
+	BMI160_SCAN_EXT_MAGN_Y,
+	BMI160_SCAN_EXT_MAGN_Z,
+	BMI160_SCAN_RHALL,
+	BMI160_SCAN_GYRO_X,
+	BMI160_SCAN_GYRO_Y,
+	BMI160_SCAN_GYRO_Z,
+	BMI160_SCAN_ACCEL_X,
+	BMI160_SCAN_ACCEL_Y,
+	BMI160_SCAN_ACCEL_Z,
+	BMI160_SCAN_TIMESTAMP,
+};
+
+enum bmi160_sensor_type {
+	BMI160_ACCEL	= 0,
+	BMI160_GYRO,
+	BMI160_EXT_MAGN,
+	BMI160_NUM_SENSORS /* must be last */
+};
+
+struct bmi160_data {
+	struct regmap *regmap;
+};
+
+const struct regmap_config bmi160_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+};
+EXPORT_SYMBOL(bmi160_regmap_config);
+
+struct bmi160_regs {
+	u8 data; /* LSB byte register for X-axis */
+	u8 config;
+	u8 config_odr_mask;
+	u8 config_bwp_mask;
+	u8 range;
+	u8 pmu_cmd_normal;
+	u8 pmu_cmd_suspend;
+};
+
+static struct bmi160_regs bmi160_regs[] = {
+	[BMI160_ACCEL] = {
+		.data	= BMI160_REG_DATA_ACCEL_XOUT_L,
+		.config	= BMI160_REG_ACCEL_CONFIG,
+		.config_odr_mask = BMI160_ACCEL_CONFIG_ODR_MASK,
+		.config_bwp_mask = BMI160_ACCEL_CONFIG_BWP_MASK,
+		.range	= BMI160_REG_ACCEL_RANGE,
+		.pmu_cmd_normal = BMI160_CMD_ACCEL_PM_NORMAL,
+		.pmu_cmd_suspend = BMI160_CMD_ACCEL_PM_SUSPEND,
+	},
+	[BMI160_GYRO] = {
+		.data	= BMI160_REG_DATA_GYRO_XOUT_L,
+		.config	= BMI160_REG_GYRO_CONFIG,
+		.config_odr_mask = BMI160_GYRO_CONFIG_ODR_MASK,
+		.config_bwp_mask = BMI160_GYRO_CONFIG_BWP_MASK,
+		.range	= BMI160_REG_GYRO_RANGE,
+		.pmu_cmd_normal = BMI160_CMD_GYRO_PM_NORMAL,
+		.pmu_cmd_suspend = BMI160_CMD_GYRO_PM_SUSPEND,
+	},
+};
+
+struct bmi160_pmu_time {
+	unsigned long min;
+	unsigned long max;
+};
+
+static struct bmi160_pmu_time bmi160_pmu_time[] = {
+	[BMI160_ACCEL] = {
+		.min = BMI160_ACCEL_PMU_MIN_USLEEP,
+		.max = BMI160_ACCEL_PMU_MAX_USLEEP
+	},
+	[BMI160_GYRO] = {
+		.min = BMI160_GYRO_PMU_MIN_USLEEP,
+		.max = BMI160_GYRO_PMU_MIN_USLEEP,
+	},
+};
+
+struct bmi160_scale {
+	u8 bits;
+	int uscale;
+};
+
+struct bmi160_odr {
+	u8 bits;
+	int odr;
+	int uodr;
+};
+
+static const struct bmi160_scale bmi160_accel_scale[] = {
+	{ BMI160_ACCEL_RANGE_2G, 598},
+	{ BMI160_ACCEL_RANGE_4G, 1197},
+	{ BMI160_ACCEL_RANGE_8G, 2394},
+	{ BMI160_ACCEL_RANGE_16G, 4788},
+};
+
+static const struct bmi160_scale bmi160_gyro_scale[] = {
+	{ BMI160_GYRO_RANGE_2000DPS, 1065},
+	{ BMI160_GYRO_RANGE_1000DPS, 532},
+	{ BMI160_GYRO_RANGE_500DPS, 266},
+	{ BMI160_GYRO_RANGE_250DPS, 133},
+	{ BMI160_GYRO_RANGE_125DPS, 66},
+};
+
+struct bmi160_scale_item {
+	const struct bmi160_scale *tbl;
+	int num;
+};
+
+static const struct  bmi160_scale_item bmi160_scale_table[] = {
+	[BMI160_ACCEL] = {
+		.tbl	= bmi160_accel_scale,
+		.num	= ARRAY_SIZE(bmi160_accel_scale),
+	},
+	[BMI160_GYRO] = {
+		.tbl	= bmi160_gyro_scale,
+		.num	= ARRAY_SIZE(bmi160_gyro_scale),
+	},
+};
+
+static const struct bmi160_odr bmi160_accel_odr[] = {
+	{0x01, 0, 78125},
+	{0x02, 1, 5625},
+	{0x03, 3, 125},
+	{0x04, 6, 25},
+	{0x05, 12, 5},
+	{0x06, 25, 0},
+	{0x07, 50, 0},
+	{0x08, 100, 0},
+	{0x09, 200, 0},
+	{0x0A, 400, 0},
+	{0x0B, 800, 0},
+	{0x0C, 1600, 0},
+};
+
+static const struct bmi160_odr bmi160_gyro_odr[] = {
+	{0x06, 25, 0},
+	{0x07, 50, 0},
+	{0x08, 100, 0},
+	{0x09, 200, 0},
+	{0x0A, 400, 0},
+	{0x0B, 8000, 0},
+	{0x0C, 1600, 0},
+	{0x0D, 3200, 0},
+};
+
+struct bmi160_odr_item {
+	const struct bmi160_odr *tbl;
+	int num;
+};
+
+static const struct  bmi160_odr_item bmi160_odr_table[] = {
+	[BMI160_ACCEL] = {
+		.tbl	= bmi160_accel_odr,
+		.num	= ARRAY_SIZE(bmi160_accel_odr),
+	},
+	[BMI160_GYRO] = {
+		.tbl	= bmi160_gyro_odr,
+		.num	= ARRAY_SIZE(bmi160_gyro_odr),
+	},
+};
+
+static const struct iio_chan_spec bmi160_channels[] = {
+	BMI160_CHANNEL(IIO_ACCEL, X, BMI160_SCAN_ACCEL_X),
+	BMI160_CHANNEL(IIO_ACCEL, Y, BMI160_SCAN_ACCEL_Y),
+	BMI160_CHANNEL(IIO_ACCEL, Z, BMI160_SCAN_ACCEL_Z),
+	BMI160_CHANNEL(IIO_ANGL_VEL, X, BMI160_SCAN_GYRO_X),
+	BMI160_CHANNEL(IIO_ANGL_VEL, Y, BMI160_SCAN_GYRO_Y),
+	BMI160_CHANNEL(IIO_ANGL_VEL, Z, BMI160_SCAN_GYRO_Z),
+	IIO_CHAN_SOFT_TIMESTAMP(BMI160_SCAN_TIMESTAMP),
+};
+
+static enum bmi160_sensor_type bmi160_to_sensor(enum iio_chan_type iio_type)
+{
+	switch (iio_type) {
+	case IIO_ACCEL:
+		return BMI160_ACCEL;
+	case IIO_ANGL_VEL:
+		return BMI160_GYRO;
+	default:
+		return -EINVAL;
+	}
+}
+
+static
+int bmi160_set_mode(struct bmi160_data *data, enum bmi160_sensor_type t,
+		    bool mode)
+{
+	int ret;
+	u8 cmd;
+
+	if (mode)
+		cmd = bmi160_regs[t].pmu_cmd_normal;
+	else
+		cmd = bmi160_regs[t].pmu_cmd_suspend;
+
+	ret = regmap_write(data->regmap, BMI160_REG_CMD, cmd);
+	if (ret < 0)
+		return ret;
+
+	usleep_range(bmi160_pmu_time[t].min, bmi160_pmu_time[t].max);
+
+	return 0;
+}
+
+static
+int bmi160_set_scale(struct bmi160_data *data, enum bmi160_sensor_type t,
+		     int uscale)
+{
+	int i;
+
+	for (i = 0; i < bmi160_scale_table[t].num; i++)
+		if (bmi160_scale_table[t].tbl[i].uscale == uscale)
+			break;
+
+	if (i == bmi160_scale_table[t].num)
+		return -EINVAL;
+
+	return regmap_write(data->regmap, bmi160_regs[t].range,
+			    bmi160_scale_table[t].tbl[i].bits);
+}
+
+static
+int bmi160_get_scale(struct bmi160_data *data, enum bmi160_sensor_type t,
+		     int *uscale)
+{
+	int i, ret, val;
+
+	ret = regmap_read(data->regmap, bmi160_regs[t].range, &val);
+	if (ret < 0)
+		return ret;
+
+	for (i = 0; i < bmi160_scale_table[t].num; i++)
+		if (bmi160_scale_table[t].tbl[i].bits == val) {
+			*uscale = bmi160_scale_table[t].tbl[i].uscale;
+			return 0;
+		}
+
+	return -EINVAL;
+}
+
+static int bmi160_get_data(struct bmi160_data *data, int chan_type,
+			   int axis, int *val)
+{
+	u8 reg;
+	int ret;
+	__le16 sample;
+	enum bmi160_sensor_type t = bmi160_to_sensor(chan_type);
+
+	reg = bmi160_regs[t].data + (axis - IIO_MOD_X) * sizeof(__le16);
+
+	ret = regmap_bulk_read(data->regmap, reg, &sample, sizeof(__le16));
+	if (ret < 0)
+		return ret;
+
+	*val = sign_extend32(le16_to_cpu(sample), 15);
+
+	return 0;
+}
+
+static
+int bmi160_set_odr(struct bmi160_data *data, enum bmi160_sensor_type t,
+		   int odr, int uodr)
+{
+	int i;
+
+	for (i = 0; i < bmi160_odr_table[t].num; i++)
+		if (bmi160_odr_table[t].tbl[i].odr == odr &&
+		    bmi160_odr_table[t].tbl[i].uodr == uodr)
+			break;
+
+	if (i >= bmi160_odr_table[t].num)
+		return -EINVAL;
+
+	return regmap_update_bits(data->regmap,
+				  bmi160_regs[t].config,
+				  bmi160_odr_table[t].tbl[i].bits,
+				  bmi160_regs[t].config_odr_mask);
+}
+
+static int bmi160_get_odr(struct bmi160_data *data, enum bmi160_sensor_type t,
+			  int *odr, int *uodr)
+{
+	int i, val, ret;
+
+	ret = regmap_read(data->regmap, bmi160_regs[t].config, &val);
+	if (ret < 0)
+		return ret;
+
+	val &= bmi160_regs[t].config_odr_mask;
+
+	for (i = 0; i < bmi160_odr_table[t].num; i++)
+		if (val == bmi160_odr_table[t].tbl[i].bits)
+			break;
+
+	if (i >= bmi160_odr_table[t].num)
+		return -EINVAL;
+
+	*odr = bmi160_odr_table[t].tbl[i].odr;
+	*uodr = bmi160_odr_table[t].tbl[i].uodr;
+
+	return 0;
+}
+
+static irqreturn_t bmi160_trigger_handler(int irq, void *p)
+{
+	struct iio_poll_func *pf = p;
+	struct iio_dev *indio_dev = pf->indio_dev;
+	struct bmi160_data *data = iio_priv(indio_dev);
+	s16 buf[16]; /* 3 sens x 3 axis x s16 + 3 x s16 pad + 4 x s16 tstamp */
+	int i, ret, j = 0, base = BMI160_REG_DATA_MAGN_XOUT_L;
+	__le16 sample;
+
+	for_each_set_bit(i, indio_dev->active_scan_mask,
+			 indio_dev->masklength) {
+		ret = regmap_bulk_read(data->regmap, base + i * sizeof(__le16),
+				       &sample, sizeof(__le16));
+		if (ret < 0)
+			goto done;
+		buf[j++] = sample;
+	}
+
+	iio_push_to_buffers_with_timestamp(indio_dev, buf, iio_get_time_ns());
+done:
+	iio_trigger_notify_done(indio_dev->trig);
+	return IRQ_HANDLED;
+}
+
+static int bmi160_read_raw(struct iio_dev *indio_dev,
+			   struct iio_chan_spec const *chan,
+			   int *val, int *val2, long mask)
+{
+	int ret;
+	struct bmi160_data *data = iio_priv(indio_dev);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		ret = bmi160_get_data(data, chan->type, chan->channel2, val);
+		if (ret < 0)
+			return ret;
+		return IIO_VAL_INT;
+	case IIO_CHAN_INFO_SCALE:
+		*val = 0;
+		ret = bmi160_get_scale(data,
+				       bmi160_to_sensor(chan->type), val2);
+		return ret < 0 ? ret : IIO_VAL_INT_PLUS_MICRO;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		ret = bmi160_get_odr(data, bmi160_to_sensor(chan->type),
+				     val, val2);
+		return ret < 0 ? ret : IIO_VAL_INT_PLUS_MICRO;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int bmi160_write_raw(struct iio_dev *indio_dev,
+			    struct iio_chan_spec const *chan,
+			    int val, int val2, long mask)
+{
+	struct bmi160_data *data = iio_priv(indio_dev);
+
+	switch (mask) {
+	case IIO_CHAN_INFO_SCALE:
+		return bmi160_set_scale(data,
+					bmi160_to_sensor(chan->type), val2);
+		break;
+	case IIO_CHAN_INFO_SAMP_FREQ:
+		return bmi160_set_odr(data, bmi160_to_sensor(chan->type),
+				      val, val2);
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static const struct iio_info bmi160_info = {
+	.driver_module = THIS_MODULE,
+	.read_raw = bmi160_read_raw,
+	.write_raw = bmi160_write_raw,
+};
+
+static const char *bmi160_match_acpi_device(struct device *dev)
+{
+	const struct acpi_device_id *id;
+
+	id = acpi_match_device(dev->driver->acpi_match_table, dev);
+	if (!id)
+		return NULL;
+
+	return dev_name(dev);
+}
+
+static int bmi160_chip_init(struct bmi160_data *data, bool use_spi)
+{
+	int ret;
+	unsigned int val;
+	struct device *dev = regmap_get_device(data->regmap);
+
+	ret = regmap_write(data->regmap, BMI160_REG_CMD, BMI160_CMD_SOFTRESET);
+	if (ret < 0)
+		return ret;
+
+	usleep_range(BMI160_SOFTRESET_USLEEP, BMI160_SOFTRESET_USLEEP + 1);
+
+	/*
+	 * CS rising edge is needed before starting SPI, so do a dummy read
+	 * See Section 3.2.1, page 86 of the datasheet
+	 */
+	if (use_spi) {
+		ret = regmap_read(data->regmap, BMI160_REG_DUMMY, &val);
+		if (ret < 0)
+			return ret;
+	}
+
+	ret = regmap_read(data->regmap, BMI160_REG_CHIP_ID, &val);
+	if (ret < 0) {
+		dev_err(dev, "Error reading chip id\n");
+		return ret;
+	}
+	if (val != BMI160_CHIP_ID_VAL) {
+		dev_err(dev, "Wrong chip id, got %x expected %x\n",
+			val, BMI160_CHIP_ID_VAL);
+		return -ENODEV;
+	}
+
+	ret = bmi160_set_mode(data, BMI160_ACCEL, true);
+	if (ret < 0)
+		return ret;
+
+	ret = bmi160_set_mode(data, BMI160_GYRO, true);
+	if (ret < 0)
+		return ret;
+
+	return 0;
+}
+
+static void bmi160_chip_uninit(struct bmi160_data *data)
+{
+	bmi160_set_mode(data, BMI160_GYRO, false);
+	bmi160_set_mode(data, BMI160_ACCEL, false);
+}
+
+int bmi160_core_probe(struct device *dev, struct regmap *regmap,
+		      const char *name, bool use_spi)
+{
+	struct iio_dev *indio_dev;
+	struct bmi160_data *data;
+	int ret;
+
+	indio_dev = devm_iio_device_alloc(dev, sizeof(*data));
+	if (!indio_dev)
+		return -ENOMEM;
+
+	data = iio_priv(indio_dev);
+	dev_set_drvdata(dev, indio_dev);
+	data->regmap = regmap;
+
+	ret = bmi160_chip_init(data, use_spi);
+	if (ret < 0)
+		return ret;
+
+	if (!name && ACPI_HANDLE(dev))
+		name = bmi160_match_acpi_device(dev);
+
+	indio_dev->dev.parent = dev;
+	indio_dev->channels = bmi160_channels;
+	indio_dev->num_channels = ARRAY_SIZE(bmi160_channels);
+	indio_dev->name = name;
+	indio_dev->modes = INDIO_DIRECT_MODE;
+	indio_dev->info = &bmi160_info;
+
+	ret = iio_triggered_buffer_setup(indio_dev, NULL,
+					 bmi160_trigger_handler, NULL);
+	if (ret < 0)
+		goto uninit;
+
+	ret = iio_device_register(indio_dev);
+	if (ret < 0)
+		goto buffer_cleanup;
+
+	return 0;
+buffer_cleanup:
+	iio_triggered_buffer_cleanup(indio_dev);
+uninit:
+	bmi160_chip_uninit(data);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(bmi160_core_probe);
+
+void bmi160_core_remove(struct device *dev)
+{
+	struct iio_dev *indio_dev = dev_get_drvdata(dev);
+	struct bmi160_data *data = iio_priv(indio_dev);
+
+	iio_device_unregister(indio_dev);
+	iio_triggered_buffer_cleanup(indio_dev);
+	bmi160_chip_uninit(data);
+}
+EXPORT_SYMBOL_GPL(bmi160_core_remove);
+
+MODULE_AUTHOR("Daniel Baluta <daniel.baluta@intel.com");
+MODULE_DESCRIPTION("Bosch BMI160 driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/imu/bmi160/bmi160_i2c.c b/drivers/iio/imu/bmi160/bmi160_i2c.c
new file mode 100644
index 000000000000..07a179d8fb48
--- /dev/null
+++ b/drivers/iio/imu/bmi160/bmi160_i2c.c
@@ -0,0 +1,72 @@
+/*
+ * BMI160 - Bosch IMU, I2C bits
+ *
+ * Copyright (c) 2016, Intel Corporation.
+ *
+ * This file is subject to the terms and conditions of version 2 of
+ * the GNU General Public License.  See the file COPYING in the main
+ * directory of this archive for more details.
+ *
+ * 7-bit I2C slave address is:
+ *      - 0x68 if SDO is pulled to GND
+ *      - 0x69 if SDO is pulled to VDDIO
+ */
+#include <linux/module.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/acpi.h>
+
+#include "bmi160.h"
+
+static int bmi160_i2c_probe(struct i2c_client *client,
+			    const struct i2c_device_id *id)
+{
+	struct regmap *regmap;
+	const char *name = NULL;
+
+	regmap = devm_regmap_init_i2c(client, &bmi160_regmap_config);
+	if (IS_ERR(regmap)) {
+		dev_err(&client->dev, "Failed to register i2c regmap %d\n",
+			(int)PTR_ERR(regmap));
+		return PTR_ERR(regmap);
+	}
+
+	if (id)
+		name = id->name;
+
+	return bmi160_core_probe(&client->dev, regmap, name, false);
+}
+
+static int bmi160_i2c_remove(struct i2c_client *client)
+{
+	bmi160_core_remove(&client->dev);
+
+	return 0;
+}
+
+static const struct i2c_device_id bmi160_i2c_id[] = {
+	{"bmi160", 0},
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, bmi160_i2c_id);
+
+static const struct acpi_device_id bmi160_acpi_match[] = {
+	{"BMI0160", 0},
+	{ },
+};
+MODULE_DEVICE_TABLE(acpi, bmi160_acpi_match);
+
+static struct i2c_driver bmi160_i2c_driver = {
+	.driver = {
+		.name			= "bmi160_i2c",
+		.acpi_match_table	= ACPI_PTR(bmi160_acpi_match),
+	},
+	.probe		= bmi160_i2c_probe,
+	.remove		= bmi160_i2c_remove,
+	.id_table	= bmi160_i2c_id,
+};
+module_i2c_driver(bmi160_i2c_driver);
+
+MODULE_AUTHOR("Daniel Baluta <daniel.baluta@intel.com>");
+MODULE_DESCRIPTION("BMI160 I2C driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/imu/bmi160/bmi160_spi.c b/drivers/iio/imu/bmi160/bmi160_spi.c
new file mode 100644
index 000000000000..1ec8b12bd984
--- /dev/null
+++ b/drivers/iio/imu/bmi160/bmi160_spi.c
@@ -0,0 +1,63 @@
+/*
+ * BMI160 - Bosch IMU, SPI bits
+ *
+ * Copyright (c) 2016, Intel Corporation.
+ *
+ * This file is subject to the terms and conditions of version 2 of
+ * the GNU General Public License.  See the file COPYING in the main
+ * directory of this archive for more details.
+ */
+#include <linux/module.h>
+#include <linux/spi/spi.h>
+#include <linux/regmap.h>
+#include <linux/acpi.h>
+
+#include "bmi160.h"
+
+static int bmi160_spi_probe(struct spi_device *spi)
+{
+	struct regmap *regmap;
+	const struct spi_device_id *id = spi_get_device_id(spi);
+
+	regmap = devm_regmap_init_spi(spi, &bmi160_regmap_config);
+	if (IS_ERR(regmap)) {
+		dev_err(&spi->dev, "Failed to register spi regmap %d\n",
+			(int)PTR_ERR(regmap));
+		return PTR_ERR(regmap);
+	}
+	return bmi160_core_probe(&spi->dev, regmap, id->name, true);
+}
+
+static int bmi160_spi_remove(struct spi_device *spi)
+{
+	bmi160_core_remove(&spi->dev);
+
+	return 0;
+}
+
+static const struct spi_device_id bmi160_spi_id[] = {
+	{"bmi160", 0},
+	{}
+};
+MODULE_DEVICE_TABLE(spi, bmi160_spi_id);
+
+static const struct acpi_device_id bmi160_acpi_match[] = {
+	{"BMI0160", 0},
+	{ },
+};
+MODULE_DEVICE_TABLE(acpi, bmi160_acpi_match);
+
+static struct spi_driver bmi160_spi_driver = {
+	.probe		= bmi160_spi_probe,
+	.remove		= bmi160_spi_remove,
+	.id_table	= bmi160_spi_id,
+	.driver = {
+		.acpi_match_table = ACPI_PTR(bmi160_acpi_match),
+		.name	= "bmi160_spi",
+	},
+};
+module_spi_driver(bmi160_spi_driver);
+
+MODULE_AUTHOR("Daniel Baluta <daniel.baluta@intel.com");
+MODULE_DESCRIPTION("Bosch BMI160 SPI driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/iio/imu/inv_mpu6050/Kconfig b/drivers/iio/imu/inv_mpu6050/Kconfig
index 847455a2d6bb..f756feecfa4c 100644
--- a/drivers/iio/imu/inv_mpu6050/Kconfig
+++ b/drivers/iio/imu/inv_mpu6050/Kconfig
@@ -13,10 +13,8 @@ config INV_MPU6050_I2C
 	select INV_MPU6050_IIO
 	select REGMAP_I2C
 	help
-	  This driver supports the Invensense MPU6050 devices.
-	  This driver can also support MPU6500 in MPU6050 compatibility mode
-	  and also in MPU6500 mode with some limitations.
-	  It is a gyroscope/accelerometer combo device.
+	  This driver supports the Invensense MPU6050/6500/9150 motion tracking
+	  devices over I2C.
 	  This driver can be built as a module. The module will be called
 	  inv-mpu6050-i2c.
 
@@ -26,7 +24,7 @@ config INV_MPU6050_SPI
 	select INV_MPU6050_IIO
 	select REGMAP_SPI
 	help
-	  This driver supports the Invensense MPU6050 devices.
-	  It is a gyroscope/accelerometer combo device.
+	  This driver supports the Invensense MPU6000/6500/9150 motion tracking
+	  devices over SPI.
 	  This driver can be built as a module. The module will be called
 	  inv-mpu6050-spi.
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
index d192953e9a38..b269b375ca34 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_core.c
@@ -88,16 +88,29 @@ static const struct inv_mpu6050_chip_config chip_config_6050 = {
 	.accl_fs = INV_MPU6050_FS_02G,
 };
 
+/* Indexed by enum inv_devices */
 static const struct inv_mpu6050_hw hw_info[] = {
 	{
-		.num_reg = 117,
+		.whoami = INV_MPU6050_WHOAMI_VALUE,
+		.name = "MPU6050",
+		.reg = &reg_set_6050,
+		.config = &chip_config_6050,
+	},
+	{
+		.whoami = INV_MPU6500_WHOAMI_VALUE,
 		.name = "MPU6500",
 		.reg = &reg_set_6500,
 		.config = &chip_config_6050,
 	},
 	{
-		.num_reg = 117,
-		.name = "MPU6050",
+		.whoami = INV_MPU6000_WHOAMI_VALUE,
+		.name = "MPU6000",
+		.reg = &reg_set_6050,
+		.config = &chip_config_6050,
+	},
+	{
+		.whoami = INV_MPU9150_WHOAMI_VALUE,
+		.name = "MPU9150",
 		.reg = &reg_set_6050,
 		.config = &chip_config_6050,
 	},
@@ -600,6 +613,10 @@ inv_fifo_rate_show(struct device *dev, struct device_attribute *attr,
 /**
  * inv_attr_show() - calling this function will show current
  *                    parameters.
+ *
+ * Deprecated in favor of IIO mounting matrix API.
+ *
+ * See inv_get_mount_matrix()
  */
 static ssize_t inv_attr_show(struct device *dev, struct device_attribute *attr,
 			     char *buf)
@@ -644,6 +661,18 @@ static int inv_mpu6050_validate_trigger(struct iio_dev *indio_dev,
 	return 0;
 }
 
+static const struct iio_mount_matrix *
+inv_get_mount_matrix(const struct iio_dev *indio_dev,
+		     const struct iio_chan_spec *chan)
+{
+	return &((struct inv_mpu6050_state *)iio_priv(indio_dev))->orientation;
+}
+
+static const struct iio_chan_spec_ext_info inv_ext_info[] = {
+	IIO_MOUNT_MATRIX(IIO_SHARED_BY_TYPE, inv_get_mount_matrix),
+	{ },
+};
+
 #define INV_MPU6050_CHAN(_type, _channel2, _index)                    \
 	{                                                             \
 		.type = _type,                                        \
@@ -660,6 +689,7 @@ static int inv_mpu6050_validate_trigger(struct iio_dev *indio_dev,
 				.shift = 0,                           \
 				.endianness = IIO_BE,                 \
 			     },                                       \
+		.ext_info = inv_ext_info,                             \
 	}
 
 static const struct iio_chan_spec inv_mpu_channels[] = {
@@ -692,14 +722,16 @@ static IIO_CONST_ATTR(in_accel_scale_available,
 					  "0.000598 0.001196 0.002392 0.004785");
 static IIO_DEV_ATTR_SAMP_FREQ(S_IRUGO | S_IWUSR, inv_fifo_rate_show,
 	inv_mpu6050_fifo_rate_store);
+
+/* Deprecated: kept for userspace backward compatibility. */
 static IIO_DEVICE_ATTR(in_gyro_matrix, S_IRUGO, inv_attr_show, NULL,
 	ATTR_GYRO_MATRIX);
 static IIO_DEVICE_ATTR(in_accel_matrix, S_IRUGO, inv_attr_show, NULL,
 	ATTR_ACCL_MATRIX);
 
 static struct attribute *inv_attributes[] = {
-	&iio_dev_attr_in_gyro_matrix.dev_attr.attr,
-	&iio_dev_attr_in_accel_matrix.dev_attr.attr,
+	&iio_dev_attr_in_gyro_matrix.dev_attr.attr,  /* deprecated */
+	&iio_dev_attr_in_accel_matrix.dev_attr.attr, /* deprecated */
 	&iio_dev_attr_sampling_frequency.dev_attr.attr,
 	&iio_const_attr_sampling_frequency_available.dev_attr.attr,
 	&iio_const_attr_in_accel_scale_available.dev_attr.attr,
@@ -726,6 +758,7 @@ static const struct iio_info mpu_info = {
 static int inv_check_and_setup_chip(struct inv_mpu6050_state *st)
 {
 	int result;
+	unsigned int regval;
 
 	st->hw  = &hw_info[st->chip_type];
 	st->reg = hw_info[st->chip_type].reg;
@@ -736,6 +769,17 @@ static int inv_check_and_setup_chip(struct inv_mpu6050_state *st)
 	if (result)
 		return result;
 	msleep(INV_MPU6050_POWER_UP_TIME);
+
+	/* check chip self-identification */
+	result = regmap_read(st->map, INV_MPU6050_REG_WHOAMI, &regval);
+	if (result)
+		return result;
+	if (regval != st->hw->whoami) {
+		dev_warn(regmap_get_device(st->map),
+				"whoami mismatch got %#02x expected %#02hhx for %s\n",
+				regval, st->hw->whoami, st->hw->name);
+	}
+
 	/*
 	 * toggle power state. After reset, the sleep bit could be on
 	 * or off depending on the OTP settings. Toggling power would
@@ -774,14 +818,31 @@ int inv_mpu_core_probe(struct regmap *regmap, int irq, const char *name,
 	if (!indio_dev)
 		return -ENOMEM;
 
+	BUILD_BUG_ON(ARRAY_SIZE(hw_info) != INV_NUM_PARTS);
+	if (chip_type < 0 || chip_type >= INV_NUM_PARTS) {
+		dev_err(dev, "Bad invensense chip_type=%d name=%s\n",
+				chip_type, name);
+		return -ENODEV;
+	}
 	st = iio_priv(indio_dev);
 	st->chip_type = chip_type;
 	st->powerup_count = 0;
 	st->irq = irq;
 	st->map = regmap;
+
 	pdata = dev_get_platdata(dev);
-	if (pdata)
+	if (!pdata) {
+		result = of_iio_read_mount_matrix(dev, "mount-matrix",
+						  &st->orientation);
+		if (result) {
+			dev_err(dev, "Failed to retrieve mounting matrix %d\n",
+				result);
+			return result;
+		}
+	} else {
 		st->plat_data = *pdata;
+	}
+
 	/* power is turned on inside check chip type*/
 	result = inv_check_and_setup_chip(st);
 	if (result)
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c
index 5ee4e0dc093e..1a424a6561de 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_i2c.c
@@ -202,13 +202,14 @@ static int inv_mpu_remove(struct i2c_client *client)
 static const struct i2c_device_id inv_mpu_id[] = {
 	{"mpu6050", INV_MPU6050},
 	{"mpu6500", INV_MPU6500},
+	{"mpu9150", INV_MPU9150},
 	{}
 };
 
 MODULE_DEVICE_TABLE(i2c, inv_mpu_id);
 
 static const struct acpi_device_id inv_acpi_match[] = {
-	{"INVN6500", 0},
+	{"INVN6500", INV_MPU6500},
 	{ },
 };
 
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
index e302a49703bf..47ca25b94a73 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_iio.h
@@ -68,6 +68,7 @@ enum inv_devices {
 	INV_MPU6050,
 	INV_MPU6500,
 	INV_MPU6000,
+	INV_MPU9150,
 	INV_NUM_PARTS
 };
 
@@ -93,13 +94,13 @@ struct inv_mpu6050_chip_config {
 
 /**
  *  struct inv_mpu6050_hw - Other important hardware information.
- *  @num_reg:	Number of registers on device.
+ *  @whoami:	Self identification byte from WHO_AM_I register
  *  @name:      name of the chip.
  *  @reg:   register map of the chip.
  *  @config:    configuration of the chip.
  */
 struct inv_mpu6050_hw {
-	u8 num_reg;
+	u8 whoami;
 	u8 *name;
 	const struct inv_mpu6050_reg_map *reg;
 	const struct inv_mpu6050_chip_config *config;
@@ -114,7 +115,8 @@ struct inv_mpu6050_hw {
  *  @hw:		Other hardware-specific information.
  *  @chip_type:		chip type.
  *  @time_stamp_lock:	spin lock to time stamp.
- *  @plat_data:		platform data.
+ *  @plat_data:		platform data (deprecated in favor of @orientation).
+ *  @orientation:	sensor chip orientation relative to main hardware.
  *  @timestamps:        kfifo queue to store time stamp.
  *  @map		regmap pointer.
  *  @irq		interrupt number.
@@ -131,6 +133,7 @@ struct inv_mpu6050_state {
 	struct i2c_client *mux_client;
 	unsigned int powerup_count;
 	struct inv_mpu6050_platform_data plat_data;
+	struct iio_mount_matrix orientation;
 	DECLARE_KFIFO(timestamps, long long, TIMESTAMP_FIFO_SIZE);
 	struct regmap *map;
 	int irq;
@@ -215,6 +218,13 @@ struct inv_mpu6050_state {
 #define INV_MPU6050_MIN_FIFO_RATE            4
 #define INV_MPU6050_ONE_K_HZ                 1000
 
+#define INV_MPU6050_REG_WHOAMI			117
+
+#define INV_MPU6000_WHOAMI_VALUE		0x68
+#define INV_MPU6050_WHOAMI_VALUE		0x68
+#define INV_MPU6500_WHOAMI_VALUE		0x70
+#define INV_MPU9150_WHOAMI_VALUE		0x68
+
 /* scan element definition */
 enum inv_mpu6050_scan {
 	INV_MPU6050_SCAN_ACCL_X,
diff --git a/drivers/iio/imu/inv_mpu6050/inv_mpu_spi.c b/drivers/iio/imu/inv_mpu6050/inv_mpu_spi.c
index 7bcb8d839f05..190a4a51c830 100644
--- a/drivers/iio/imu/inv_mpu6050/inv_mpu_spi.c
+++ b/drivers/iio/imu/inv_mpu6050/inv_mpu_spi.c
@@ -44,9 +44,19 @@ static int inv_mpu_i2c_disable(struct iio_dev *indio_dev)
 static int inv_mpu_probe(struct spi_device *spi)
 {
 	struct regmap *regmap;
-	const struct spi_device_id *id = spi_get_device_id(spi);
-	const char *name = id ? id->name : NULL;
-	const int chip_type = id ? id->driver_data : 0;
+	const struct spi_device_id *spi_id;
+	const struct acpi_device_id *acpi_id;
+	const char *name = NULL;
+	enum inv_devices chip_type;
+
+	if ((spi_id = spi_get_device_id(spi))) {
+		chip_type = (enum inv_devices)spi_id->driver_data;
+		name = spi_id->name;
+	} else if ((acpi_id = acpi_match_device(spi->dev.driver->acpi_match_table, &spi->dev))) {
+		chip_type = (enum inv_devices)acpi_id->driver_data;
+	} else {
+		return -ENODEV;
+	}
 
 	regmap = devm_regmap_init_spi(spi, &inv_mpu_regmap_config);
 	if (IS_ERR(regmap)) {
@@ -70,13 +80,15 @@ static int inv_mpu_remove(struct spi_device *spi)
  */
 static const struct spi_device_id inv_mpu_id[] = {
 	{"mpu6000", INV_MPU6000},
+	{"mpu6500", INV_MPU6500},
+	{"mpu9150", INV_MPU9150},
 	{}
 };
 
 MODULE_DEVICE_TABLE(spi, inv_mpu_id);
 
 static const struct acpi_device_id inv_acpi_match[] = {
-	{"INVN6000", 0},
+	{"INVN6000", INV_MPU6000},
 	{ },
 };
 MODULE_DEVICE_TABLE(acpi, inv_acpi_match);