Merge branch 'for-linus2' of git://git.profusion.mobi/users/lucas/linux-2.6

* 'for-linus2' of git://git.profusion.mobi/users/lucas/linux-2.6:
  Fix common misspellings

10 files changed, 12 insertions, 12 deletions

diff --git a/drivers/hwmon/abituguru.c b/drivers/hwmon/abituguru.c
index 0e05aa179eaa..e7d4c4687f02 100644
--- a/drivers/hwmon/abituguru.c
+++ b/drivers/hwmon/abituguru.c
@@ -1422,7 +1422,7 @@ static int __init abituguru_detect(void)
 	   at DATA and 0xAC, when this driver has already been loaded once
 	   DATA will hold 0x08. For most uGuru's CMD will hold 0xAC in either
 	   scenario but some will hold 0x00.
-	   Some uGuru's initally hold 0x09 at DATA and will only hold 0x08
+	   Some uGuru's initially hold 0x09 at DATA and will only hold 0x08
 	   after reading CMD first, so CMD must be read first! */
 	u8 cmd_val = inb_p(ABIT_UGURU_BASE + ABIT_UGURU_CMD);
 	u8 data_val = inb_p(ABIT_UGURU_BASE + ABIT_UGURU_DATA);
diff --git a/drivers/hwmon/abituguru3.c b/drivers/hwmon/abituguru3.c
index 034cebfcd273..e89d572e3320 100644
--- a/drivers/hwmon/abituguru3.c
+++ b/drivers/hwmon/abituguru3.c
@@ -151,7 +151,7 @@ struct abituguru3_data {
 	/* Pointer to the sensors info for the detected motherboard */
 	const struct abituguru3_sensor_info *sensors;
 
-	/* The abituguru3 supports upto 48 sensors, and thus has registers
+	/* The abituguru3 supports up to 48 sensors, and thus has registers
 	   sets for 48 sensors, for convienence reasons / simplicity of the
 	   code we always read and store all registers for all 48 sensors */
 
diff --git a/drivers/hwmon/adm1026.c b/drivers/hwmon/adm1026.c
index be0fdd58aa29..0531867484f4 100644
--- a/drivers/hwmon/adm1026.c
+++ b/drivers/hwmon/adm1026.c
@@ -175,7 +175,7 @@ static u16 ADM1026_REG_TEMP_OFFSET[] = { 0x1e, 0x6e, 0x6f };
  * these macros are called: arguments may be evaluated more than once.
  */
 
-/* IN are scaled acording to built-in resistors.  These are the
+/* IN are scaled according to built-in resistors.  These are the
  *   voltages corresponding to 3/4 of full scale (192 or 0xc0)
  *   NOTE: The -12V input needs an additional factor to account
  *      for the Vref pullup resistor.
diff --git a/drivers/hwmon/lm85.c b/drivers/hwmon/lm85.c
index cf47e6e476ed..250d099ca398 100644
--- a/drivers/hwmon/lm85.c
+++ b/drivers/hwmon/lm85.c
@@ -130,7 +130,7 @@ enum chips {
    these macros are called: arguments may be evaluated more than once.
  */
 
-/* IN are scaled acording to built-in resistors */
+/* IN are scaled according to built-in resistors */
 static const int lm85_scaling[] = {  /* .001 Volts */
 	2500, 2250, 3300, 5000, 12000,
 	3300, 1500, 1800 /*EMC6D100*/
diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c
index 812781c655a7..c43b4e9f96a9 100644
--- a/drivers/hwmon/lm90.c
+++ b/drivers/hwmon/lm90.c
@@ -356,7 +356,7 @@ static int lm90_read16(struct i2c_client *client, u8 regh, u8 regl, u16 *value)
 	/*
 	 * There is a trick here. We have to read two registers to have the
 	 * sensor temperature, but we have to beware a conversion could occur
-	 * inbetween the readings. The datasheet says we should either use
+	 * between the readings. The datasheet says we should either use
 	 * the one-shot conversion register, which we don't want to do
 	 * (disables hardware monitoring) or monitor the busy bit, which is
 	 * impossible (we can't read the values and monitor that bit at the
diff --git a/drivers/hwmon/sht15.c b/drivers/hwmon/sht15.c
index 1a9c32d6893a..f4e617adb220 100644
--- a/drivers/hwmon/sht15.c
+++ b/drivers/hwmon/sht15.c
@@ -52,7 +52,7 @@
 #define SHT15_TSU		150	/* data setup time */
 
 /**
- * struct sht15_temppair - elements of voltage dependant temp calc
+ * struct sht15_temppair - elements of voltage dependent temp calc
  * @vdd:	supply voltage in microvolts
  * @d1:		see data sheet
  */
@@ -251,7 +251,7 @@ static inline int sht15_update_single_val(struct sht15_data *data,
 	enable_irq(gpio_to_irq(data->pdata->gpio_data));
 	if (gpio_get_value(data->pdata->gpio_data) == 0) {
 		disable_irq_nosync(gpio_to_irq(data->pdata->gpio_data));
-		/* Only relevant if the interrupt hasn't occured. */
+		/* Only relevant if the interrupt hasn't occurred. */
 		if (!atomic_read(&data->interrupt_handled))
 			schedule_work(&data->read_work);
 	}
@@ -452,7 +452,7 @@ static void sht15_bh_read_data(struct work_struct *work_s)
 		*/
 		atomic_set(&data->interrupt_handled, 0);
 		enable_irq(gpio_to_irq(data->pdata->gpio_data));
-		/* If still not occured or another handler has been scheduled */
+		/* If still not occurred or another handler has been scheduled */
 		if (gpio_get_value(data->pdata->gpio_data)
 		    || atomic_read(&data->interrupt_handled))
 			return;
diff --git a/drivers/hwmon/tmp102.c b/drivers/hwmon/tmp102.c
index 93187c3cb5e7..5bd194968801 100644
--- a/drivers/hwmon/tmp102.c
+++ b/drivers/hwmon/tmp102.c
@@ -166,7 +166,7 @@ static int __devinit tmp102_probe(struct i2c_client *client,
 
 	if (!i2c_check_functionality(client->adapter,
 				     I2C_FUNC_SMBUS_WORD_DATA)) {
-		dev_err(&client->dev, "adapter doesnt support SMBus word "
+		dev_err(&client->dev, "adapter doesn't support SMBus word "
 			"transactions\n");
 		return -ENODEV;
 	}
diff --git a/drivers/hwmon/w83791d.c b/drivers/hwmon/w83791d.c
index 400a88bde278..17cf1ab95521 100644
--- a/drivers/hwmon/w83791d.c
+++ b/drivers/hwmon/w83791d.c
@@ -556,7 +556,7 @@ static ssize_t show_fan_div(struct device *dev, struct device_attribute *attr,
 
 /* Note: we save and restore the fan minimum here, because its value is
    determined in part by the fan divisor.  This follows the principle of
-   least suprise; the user doesn't expect the fan minimum to change just
+   least surprise; the user doesn't expect the fan minimum to change just
    because the divisor changed. */
 static ssize_t store_fan_div(struct device *dev, struct device_attribute *attr,
 				const char *buf, size_t count)
diff --git a/drivers/hwmon/w83792d.c b/drivers/hwmon/w83792d.c
index 63841f8cec07..f3e7130c4cda 100644
--- a/drivers/hwmon/w83792d.c
+++ b/drivers/hwmon/w83792d.c
@@ -244,7 +244,7 @@ FAN_TO_REG(long rpm, int div)
 #define TEMP1_TO_REG(val)	(SENSORS_LIMIT(((val) < 0 ? (val)+0x100*1000 \
 					: (val)) / 1000, 0, 0xff))
 #define TEMP1_FROM_REG(val)	(((val) & 0x80 ? (val)-0x100 : (val)) * 1000)
-/* for temp2 and temp3, because they need addtional resolution */
+/* for temp2 and temp3, because they need additional resolution */
 #define TEMP_ADD_FROM_REG(val1, val2) \
 	((((val1) & 0x80 ? (val1)-0x100 \
 		: (val1)) * 1000) + ((val2 & 0x80) ? 500 : 0))
diff --git a/drivers/hwmon/w83793.c b/drivers/hwmon/w83793.c
index e3bdedfb5347..854f9117f1aa 100644
--- a/drivers/hwmon/w83793.c
+++ b/drivers/hwmon/w83793.c
@@ -1921,7 +1921,7 @@ static void w83793_update_nonvolatile(struct device *dev)
 	struct w83793_data *data = i2c_get_clientdata(client);
 	int i, j;
 	/*
-	   They are somewhat "stable" registers, and to update them everytime
+	   They are somewhat "stable" registers, and to update them every time
 	   takes so much time, it's just not worthy. Update them in a long
 	   interval to avoid exception.
 	 */