Merge tag 'imx-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/fixes

i.MX fixes for 5.5:
 - Add missing jedec,spi-nor compatible for imx6ul-14x14-evk board,
   so that SPI NOR device can be probed.
 - Fix power button of E60K02 board by removing LDORTC2 regulator.
 - A couple of fixes on serial number support of i.MX6ULL/ULZ SoCs to
   remove the boot regression caused by 8267ff89b713 ("ARM: imx: Add
   serial number support for i.MX6/7 SoCs").
 - A couple of fixes on LS1028A SoC TMU regarding to calibration data
   and reboot register configuration.
 - Fix a regression seen on imx6ul-evk board by marking always-on for
   the regulator that is shared by many peripherals.
 - Explicitly restore CONFIG_DEBUG_FS in imx_v6_v7_defconfig.

* tag 'imx-fixes-5.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
  ARM: imx: Fix boot crash if ocotp is not found
  ARM: imx_v6_v7_defconfig: Explicitly restore CONFIG_DEBUG_FS
  ARM: dts: imx6ul-evk: Fix peripheral regulator
  arm64: dts: ls1028a: fix reboot node
  arm64: dts: ls1028a: fix typo in TMU calibration data
  ARM: imx: Correct ocotp id for serial number support of i.MX6ULL/ULZ SoCs
  ARM: dts: e60k02: fix power button
  ARM: dts: imx6ul: imx6ul-14x14-evk.dtsi: Fix SPI NOR probing

Link: https://lore.kernel.org/r/20191212122427.GK15858@dragon
Signed-off-by: Olof Johansson <olof@lixom.net>

4 files changed, 27 insertions, 15 deletions

diff --git a/arch/arm/boot/dts/e60k02.dtsi b/arch/arm/boot/dts/e60k02.dtsi
index 6472b056a001..5a2c5320437d 100644
--- a/arch/arm/boot/dts/e60k02.dtsi
+++ b/arch/arm/boot/dts/e60k02.dtsi
@@ -265,11 +265,6 @@
 				regulator-name = "LDORTC1";
 				regulator-boot-on;
 			};
-
-			ldortc2_reg: LDORTC2 {
-				regulator-name = "LDORTC2";
-				regulator-boot-on;
-			};
 		};
 	};
 };
diff --git a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
index 1506eb12b21e..212144511b66 100644
--- a/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
+++ b/arch/arm/boot/dts/imx6ul-14x14-evk.dtsi
@@ -30,14 +30,26 @@
 		enable-active-high;
 	};
 
-	reg_sensors: regulator-sensors {
+	reg_peri_3v3: regulator-peri-3v3 {
 		compatible = "regulator-fixed";
 		pinctrl-names = "default";
-		pinctrl-0 = <&pinctrl_sensors_reg>;
-		regulator-name = "sensors-supply";
+		pinctrl-0 = <&pinctrl_peri_3v3>;
+		regulator-name = "VPERI_3V3";
 		regulator-min-microvolt = <3300000>;
 		regulator-max-microvolt = <3300000>;
 		gpio = <&gpio5 2 GPIO_ACTIVE_LOW>;
+		/*
+		 * If you want to want to make this dynamic please
+		 * check schematics and test all affected peripherals:
+		 *
+		 * - sensors
+		 * - ethernet phy
+		 * - can
+		 * - bluetooth
+		 * - wm8960 audio codec
+		 * - ov5640 camera
+		 */
+		regulator-always-on;
 	};
 
 	reg_can_3v3: regulator-can-3v3 {
@@ -140,6 +152,7 @@
 	pinctrl-0 = <&pinctrl_enet1>;
 	phy-mode = "rmii";
 	phy-handle = <&ethphy0>;
+	phy-supply = <&reg_peri_3v3>;
 	status = "okay";
 };
 
@@ -148,6 +161,7 @@
 	pinctrl-0 = <&pinctrl_enet2>;
 	phy-mode = "rmii";
 	phy-handle = <&ethphy1>;
+	phy-supply = <&reg_peri_3v3>;
 	status = "okay";
 
 	mdio {
@@ -193,8 +207,8 @@
 	magnetometer@e {
 		compatible = "fsl,mag3110";
 		reg = <0x0e>;
-		vdd-supply = <&reg_sensors>;
-		vddio-supply = <&reg_sensors>;
+		vdd-supply = <&reg_peri_3v3>;
+		vddio-supply = <&reg_peri_3v3>;
 	};
 };
 
@@ -227,7 +241,7 @@
 	flash0: n25q256a@0 {
 		#address-cells = <1>;
 		#size-cells = <1>;
-		compatible = "micron,n25q256a";
+		compatible = "micron,n25q256a", "jedec,spi-nor";
 		spi-max-frequency = <29000000>;
 		spi-rx-bus-width = <4>;
 		spi-tx-bus-width = <4>;
@@ -462,7 +476,7 @@
 		>;
 	};
 
-	pinctrl_sensors_reg: sensorsreggrp {
+	pinctrl_peri_3v3: peri3v3grp {
 		fsl,pins = <
 			MX6UL_PAD_SNVS_TAMPER2__GPIO5_IO02	0x1b0b0
 		>;
diff --git a/arch/arm/configs/imx_v6_v7_defconfig b/arch/arm/configs/imx_v6_v7_defconfig
index 26d6dee67aa6..3608e55eaecd 100644
--- a/arch/arm/configs/imx_v6_v7_defconfig
+++ b/arch/arm/configs/imx_v6_v7_defconfig
@@ -462,6 +462,7 @@ CONFIG_FONT_8x8=y
 CONFIG_FONT_8x16=y
 CONFIG_PRINTK_TIME=y
 CONFIG_MAGIC_SYSRQ=y
+CONFIG_DEBUG_FS=y
 # CONFIG_SCHED_DEBUG is not set
 CONFIG_PROVE_LOCKING=y
 # CONFIG_DEBUG_BUGVERBOSE is not set
diff --git a/arch/arm/mach-imx/cpu.c b/arch/arm/mach-imx/cpu.c
index d8118031c51f..871f98342d50 100644
--- a/arch/arm/mach-imx/cpu.c
+++ b/arch/arm/mach-imx/cpu.c
@@ -84,7 +84,7 @@ struct device * __init imx_soc_device_init(void)
 	const char *ocotp_compat = NULL;
 	struct soc_device *soc_dev;
 	struct device_node *root;
-	struct regmap *ocotp;
+	struct regmap *ocotp = NULL;
 	const char *soc_id;
 	u64 soc_uid = 0;
 	u32 val;
@@ -148,11 +148,11 @@ struct device * __init imx_soc_device_init(void)
 		soc_id = "i.MX6UL";
 		break;
 	case MXC_CPU_IMX6ULL:
-		ocotp_compat = "fsl,imx6ul-ocotp";
+		ocotp_compat = "fsl,imx6ull-ocotp";
 		soc_id = "i.MX6ULL";
 		break;
 	case MXC_CPU_IMX6ULZ:
-		ocotp_compat = "fsl,imx6ul-ocotp";
+		ocotp_compat = "fsl,imx6ull-ocotp";
 		soc_id = "i.MX6ULZ";
 		break;
 	case MXC_CPU_IMX6SLL:
@@ -175,7 +175,9 @@ struct device * __init imx_soc_device_init(void)
 		ocotp = syscon_regmap_lookup_by_compatible(ocotp_compat);
 		if (IS_ERR(ocotp))
 			pr_err("%s: failed to find %s regmap!\n", __func__, ocotp_compat);
+	}
 
+	if (!IS_ERR_OR_NULL(ocotp)) {
 		regmap_read(ocotp, OCOTP_UID_H, &val);
 		soc_uid = val;
 		regmap_read(ocotp, OCOTP_UID_L, &val);