[ARM] pxa: add support for L2 outer cache on XScale3 (attempt 2)

(20072fd0c93349e19527dd2fa9588b4335960e62 lost most of its changes
somehow, came from a mbox archive applied with git-am.  No idea
what happened.  This puts back the missing bits.  --rmk)

The initial patch from Lothar, and Lennert make it into a cleaner
one, modified and tested on PXA320 by Eric Miao.

This patch moves the L2 cache operations out of proc-xsc3.S into
dedicated outer cache support code.

CACHE_XSC3L2 can be deselected so no L2 cache specific code will be
linked in, and that L2 enable bit will not be set, this applies to
the following cases:

    a. _only_ PXA300/PXA310 support included and no L2 cache wanted
    b. PXA320 support included, but want L2 be disabled

So the enabling of L2 depends on two things:

    - CACHE_XSC3L2 is selected
    - and L2 cache is present

Where the latter is only a safeguard (previous testing shows it works
OK even when this bit is turned on).

IXP series of processors with XScale3 cannot disable L2 cache for the
moment since they depend on the L2 cache for its coherent memory, so
IXP may always select CACHE_XSC3L2.

Other L2 relevant bits are always turned on (i.e. the original code
enclosed by #if L2_CACHE_ENABLED .. #endif), as they showed no side
effects. Specifically, these bits are:

   - OC bits in TTBASE register (table walk outer cache attributes)
   - LLR Outer Cache Attributes (OC) in Auxiliary Control Register

Signed-off-by: Lothar WaÃ<9f>mann <LW@KARO-electronics.de>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>

1 files changed, 0 insertions, 22 deletions

diff --git a/arch/arm/mm/proc-xsc3.S b/arch/arm/mm/proc-xsc3.S
index 3533741a76f6..6ff53c24510f 100644
--- a/arch/arm/mm/proc-xsc3.S
+++ b/arch/arm/mm/proc-xsc3.S
@@ -52,11 +52,6 @@
 #define CACHESIZE	32768
 
 /*
- * Run with L2 enabled.
- */
-#define L2_CACHE_ENABLE	1
-
-/*
  * This macro is used to wait for a CP15 write and is needed when we
  * have to ensure that the last operation to the coprocessor was
  * completed before continuing with operation.
@@ -265,12 +260,9 @@ ENTRY(xsc3_dma_inv_range)
 	tst	r0, #CACHELINESIZE - 1
 	bic	r0, r0, #CACHELINESIZE - 1
 	mcrne	p15, 0, r0, c7, c10, 1		@ clean L1 D line
-	mcrne	p15, 1, r0, c7, c11, 1		@ clean L2 line
 	tst	r1, #CACHELINESIZE - 1
 	mcrne	p15, 0, r1, c7, c10, 1		@ clean L1 D line
-	mcrne	p15, 1, r1, c7, c11, 1		@ clean L2 line
 1:	mcr	p15, 0, r0, c7, c6, 1		@ invalidate L1 D line
-	mcr	p15, 1, r0, c7, c7, 1		@ invalidate L2 line
 	add	r0, r0, #CACHELINESIZE
 	cmp	r0, r1
 	blo	1b
@@ -288,7 +280,6 @@ ENTRY(xsc3_dma_inv_range)
 ENTRY(xsc3_dma_clean_range)
 	bic	r0, r0, #CACHELINESIZE - 1
 1:	mcr	p15, 0, r0, c7, c10, 1		@ clean L1 D line
-	mcr	p15, 1, r0, c7, c11, 1		@ clean L2 line
 	add	r0, r0, #CACHELINESIZE
 	cmp	r0, r1
 	blo	1b
@@ -306,8 +297,6 @@ ENTRY(xsc3_dma_clean_range)
 ENTRY(xsc3_dma_flush_range)
 	bic	r0, r0, #CACHELINESIZE - 1
 1:	mcr	p15, 0, r0, c7, c14, 1		@ clean/invalidate L1 D line
-	mcr	p15, 1, r0, c7, c11, 1		@ clean L2 line
-	mcr	p15, 1, r0, c7, c7, 1		@ invalidate L2 line
 	add	r0, r0, #CACHELINESIZE
 	cmp	r0, r1
 	blo	1b
@@ -347,9 +336,7 @@ ENTRY(cpu_xsc3_switch_mm)
 	mcr	p15, 0, ip, c7, c5, 0		@ invalidate L1 I cache and BTB
 	mcr	p15, 0, ip, c7, c10, 4		@ data write barrier
 	mcr	p15, 0, ip, c7, c5, 4		@ prefetch flush
-#ifdef L2_CACHE_ENABLE
 	orr	r0, r0, #0x18			@ cache the page table in L2
-#endif
 	mcr	p15, 0, r0, c2, c0, 0		@ load page table pointer
 	mcr	p15, 0, ip, c8, c7, 0		@ invalidate I and D TLBs
 	cpwait_ret lr, ip
@@ -378,12 +365,10 @@ ENTRY(cpu_xsc3_set_pte_ext)
 	orreq	r2, r2, #PTE_EXT_AP_UNO_SRW	@ yes -> user n/a, system r/w
 						@ combined with user -> user r/w
 
-#if L2_CACHE_ENABLE
 	@ If it's cacheable, it needs to be in L2 also.
 	eor	ip, r1, #L_PTE_CACHEABLE
 	tst	ip, #L_PTE_CACHEABLE
 	orreq	r2, r2, #PTE_EXT_TEX(0x5)
-#endif
 
 	tst	r3, #L_PTE_PRESENT | L_PTE_YOUNG	@ present and young?
 	movne	r2, #0				@ no -> fault
@@ -408,9 +393,7 @@ __xsc3_setup:
 	mcr	p15, 0, ip, c7, c10, 4		@ data write barrier
 	mcr	p15, 0, ip, c7, c5, 4		@ prefetch flush
 	mcr	p15, 0, ip, c8, c7, 0		@ invalidate I and D TLBs
-#if L2_CACHE_ENABLE
 	orr	r4, r4, #0x18			@ cache the page table in L2
-#endif
 	mcr	p15, 0, r4, c2, c0, 0		@ load page table pointer
 
 	mov	r0, #0				@ don't allow CP access
@@ -418,9 +401,7 @@ __xsc3_setup:
 
 	mrc	p15, 0, r0, c1, c0, 1		@ get auxiliary control reg
 	and	r0, r0, #2			@ preserve bit P bit setting
-#if L2_CACHE_ENABLE
 	orr	r0, r0, #(1 << 10)		@ enable L2 for LLR cache
-#endif
 	mcr	p15, 0, r0, c1, c0, 1		@ set auxiliary control reg
 
 	adr	r5, xsc3_crval
@@ -429,9 +410,6 @@ __xsc3_setup:
 	bic	r0, r0, r5			@ ..V. ..R. .... ..A.
 	orr	r0, r0, r6			@ ..VI Z..S .... .C.M (mmu)
 						@ ...I Z..S .... .... (uc)
-#if L2_CACHE_ENABLE
-	orr 	r0, r0, #0x04000000		@ L2 enable
-#endif
 	mov	pc, lr
 
 	.size	__xsc3_setup, . - __xsc3_setup