Merge tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc

Pull char/misc updates from Greg KH:
 "Here is the big set of char/misc and other driver subsystem patches
  for 4.15-rc1.

  There are small changes all over here, hyperv driver updates, pcmcia
  driver updates, w1 driver updats, vme driver updates, nvmem driver
  updates, and lots of other little one-off driver updates as well. The
  shortlog has the full details.

  All of these have been in linux-next for quite a while with no
  reported issues"

* tag 'char-misc-4.15-rc1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (90 commits)
  VME: Return -EBUSY when DMA list in use
  w1: keep balance of mutex locks and refcnts
  MAINTAINERS: Update VME subsystem tree.
  nvmem: sunxi-sid: add support for A64/H5's SID controller
  nvmem: imx-ocotp: Update module description
  nvmem: imx-ocotp: Enable i.MX7D OTP write support
  nvmem: imx-ocotp: Add i.MX7D timing write clock setup support
  nvmem: imx-ocotp: Move i.MX6 write clock setup to dedicated function
  nvmem: imx-ocotp: Add support for banked OTP addressing
  nvmem: imx-ocotp: Pass parameters via a struct
  nvmem: imx-ocotp: Restrict OTP write to IMX6 processors
  nvmem: uniphier: add UniPhier eFuse driver
  dt-bindings: nvmem: add description for UniPhier eFuse
  nvmem: set nvmem->owner to nvmem->dev->driver->owner if unset
  nvmem: qfprom: fix different address space warnings of sparse
  nvmem: mtk-efuse: fix different address space warnings of sparse
  nvmem: mtk-efuse: use stack for nvmem_config instead of malloc'ing it
  nvmem: imx-iim: use stack for nvmem_config instead of malloc'ing it
  thunderbolt: tb: fix use after free in tb_activate_pcie_devices
  MAINTAINERS: Add git tree for Thunderbolt development
  ...

11 files changed, 272 insertions, 6 deletions

diff --git a/Documentation/ABI/stable/sysfs-bus-vmbus b/Documentation/ABI/stable/sysfs-bus-vmbus
index 5d0125f7bcaf..d4077cc60d55 100644
--- a/Documentation/ABI/stable/sysfs-bus-vmbus
+++ b/Documentation/ABI/stable/sysfs-bus-vmbus
@@ -41,3 +41,73 @@ KernelVersion:	4.5
 Contact:	K. Y. Srinivasan <kys@microsoft.com>
 Description:	The 16 bit vendor ID of the device
 Users:		tools/hv/lsvmbus and user level RDMA libraries
+
+What:		/sys/bus/vmbus/devices/vmbus_*/channels/relid/cpu
+Date:		September. 2017
+KernelVersion:	4.14
+Contact:	Stephen Hemminger <sthemmin@microsoft.com>
+Description:	VCPU (sub)channel is affinitized to
+Users:		tools/hv/lsvmbus and other debuggig tools
+
+What:		/sys/bus/vmbus/devices/vmbus_*/channels/relid/cpu
+Date:		September. 2017
+KernelVersion:	4.14
+Contact:	Stephen Hemminger <sthemmin@microsoft.com>
+Description:	VCPU (sub)channel is affinitized to
+Users:		tools/hv/lsvmbus and other debuggig tools
+
+What:		/sys/bus/vmbus/devices/vmbus_*/channels/relid/in_mask
+Date:		September. 2017
+KernelVersion:	4.14
+Contact:	Stephen Hemminger <sthemmin@microsoft.com>
+Description:	Inbound channel signaling state
+Users:		Debugging tools
+
+What:		/sys/bus/vmbus/devices/vmbus_*/channels/relid/latency
+Date:		September. 2017
+KernelVersion:	4.14
+Contact:	Stephen Hemminger <sthemmin@microsoft.com>
+Description:	Channel signaling latency
+Users:		Debugging tools
+
+What:		/sys/bus/vmbus/devices/vmbus_*/channels/relid/out_mask
+Date:		September. 2017
+KernelVersion:	4.14
+Contact:	Stephen Hemminger <sthemmin@microsoft.com>
+Description:	Outbound channel signaling state
+Users:		Debugging tools
+
+What:		/sys/bus/vmbus/devices/vmbus_*/channels/relid/pending
+Date:		September. 2017
+KernelVersion:	4.14
+Contact:	Stephen Hemminger <sthemmin@microsoft.com>
+Description:	Channel interrupt pending state
+Users:		Debugging tools
+
+What:		/sys/bus/vmbus/devices/vmbus_*/channels/relid/read_avail
+Date:		September. 2017
+KernelVersion:	4.14
+Contact:	Stephen Hemminger <sthemmin@microsoft.com>
+Description:	Bytes availabble to read
+Users:		Debugging tools
+
+What:		/sys/bus/vmbus/devices/vmbus_*/channels/relid/write_avail
+Date:		September. 2017
+KernelVersion:	4.14
+Contact:	Stephen Hemminger <sthemmin@microsoft.com>
+Description:	Bytes availabble to write
+Users:		Debugging tools
+
+What:		/sys/bus/vmbus/devices/vmbus_*/channels/relid/events
+Date:		September. 2017
+KernelVersion:	4.14
+Contact:	Stephen Hemminger <sthemmin@microsoft.com>
+Description:	Number of times we have signaled the host
+Users:		Debugging tools
+
+What:		/sys/bus/vmbus/devices/vmbus_*/channels/relid/interrupts
+Date:		September. 2017
+KernelVersion:	4.14
+Contact:	Stephen Hemminger <sthemmin@microsoft.com>
+Description:	Number of times we have taken an interrupt (incoming)
+Users:		Debugging tools
diff --git a/Documentation/ABI/testing/sysfs-driver-w1_ds28e17 b/Documentation/ABI/testing/sysfs-driver-w1_ds28e17
new file mode 100644
index 000000000000..d301e7017afe
--- /dev/null
+++ b/Documentation/ABI/testing/sysfs-driver-w1_ds28e17
@@ -0,0 +1,21 @@
+What:		/sys/bus/w1/devices/19-<id>/speed
+Date:		Sep 2017
+KernelVersion:	4.14
+Contact:	Jan Kandziora <jjj@gmx.de>
+Description:	When written, this file sets the I2C speed on the connected
+		DS28E17 chip. When read, it reads the current setting from
+		the DS28E17 chip.
+		Valid values: 100, 400, 900 [kBaud].
+		Default 100, can be set by w1_ds28e17.speed= module parameter.
+Users:		w1_ds28e17 driver
+
+What:		/sys/bus/w1/devices/19-<id>/stretch
+Date:		Sep 2017
+KernelVersion:	4.14
+Contact:	Jan Kandziora <jjj@gmx.de>
+Description:	When written, this file sets the multiplier used to calculate
+		the busy timeout for I2C operations on the connected DS28E17
+		chip. When read, returns the current setting.
+		Valid values: 1 to 9.
+		Default 1, can be set by w1_ds28e17.stretch= module parameter.
+Users:		w1_ds28e17 driver
diff --git a/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt b/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt
index 081c49c0dac0..d69543701d5d 100644
--- a/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt
+++ b/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt
@@ -5,6 +5,7 @@ Required properties:
   "allwinner,sun4i-a10-sid"
   "allwinner,sun7i-a20-sid"
   "allwinner,sun8i-h3-sid"
+  "allwinner,sun50i-a64-sid"
 
 - reg: Should contain registers location and length
 
diff --git a/Documentation/devicetree/bindings/nvmem/amlogic-efuse.txt b/Documentation/devicetree/bindings/nvmem/amlogic-efuse.txt
index fafd85bd67a6..e3298e18de26 100644
--- a/Documentation/devicetree/bindings/nvmem/amlogic-efuse.txt
+++ b/Documentation/devicetree/bindings/nvmem/amlogic-efuse.txt
@@ -1,4 +1,4 @@
-= Amlogic eFuse device tree bindings =
+= Amlogic Meson GX eFuse device tree bindings =
 
 Required properties:
 - compatible: should be "amlogic,meson-gxbb-efuse"
diff --git a/Documentation/devicetree/bindings/nvmem/amlogic-meson-mx-efuse.txt b/Documentation/devicetree/bindings/nvmem/amlogic-meson-mx-efuse.txt
new file mode 100644
index 000000000000..a3c63954a1a4
--- /dev/null
+++ b/Documentation/devicetree/bindings/nvmem/amlogic-meson-mx-efuse.txt
@@ -0,0 +1,22 @@
+Amlogic Meson6/Meson8/Meson8b efuse
+
+Required Properties:
+- compatible: depending on the SoC this should be one of:
+	- "amlogic,meson6-efuse"
+	- "amlogic,meson8-efuse"
+	- "amlogic,meson8b-efuse"
+- reg: base address and size of the efuse registers
+- clocks: a reference to the efuse core gate clock
+- clock-names: must be "core"
+
+All properties and sub-nodes as well as the consumer bindings
+defined in nvmem.txt in this directory are also supported.
+
+
+Example:
+	efuse: nvmem@0 {
+		compatible = "amlogic,meson8-efuse";
+		reg = <0x0 0x2000>;
+		clocks = <&clkc CLKID_EFUSE>;
+		clock-names = "core";
+	};
diff --git a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt
index 1ff02afdc55a..60bec4782806 100644
--- a/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt
+++ b/Documentation/devicetree/bindings/nvmem/rockchip-efuse.txt
@@ -6,6 +6,7 @@ Required properties:
   - "rockchip,rk3188-efuse" - for RK3188 SoCs.
   - "rockchip,rk3228-efuse" - for RK3228 SoCs.
   - "rockchip,rk3288-efuse" - for RK3288 SoCs.
+  - "rockchip,rk3368-efuse" - for RK3368 SoCs.
   - "rockchip,rk3399-efuse" - for RK3399 SoCs.
 - reg: Should contain the registers location and exact eFuse size
 - clocks: Should be the clock id of eFuse
diff --git a/Documentation/devicetree/bindings/nvmem/snvs-lpgpr.txt b/Documentation/devicetree/bindings/nvmem/snvs-lpgpr.txt
new file mode 100644
index 000000000000..20bc49b49799
--- /dev/null
+++ b/Documentation/devicetree/bindings/nvmem/snvs-lpgpr.txt
@@ -0,0 +1,20 @@
+Device tree bindings for Low Power General Purpose Register found in i.MX6Q/D
+Secure Non-Volatile Storage.
+
+This DT node should be represented as a sub-node of a "syscon",
+"simple-mfd" node.
+
+Required properties:
+- compatible: should be one of the fallowing variants:
+	"fsl,imx6q-snvs-lpgpr" for Freescale i.MX6Q/D/DL/S
+	"fsl,imx6ul-snvs-lpgpr" for Freescale i.MX6UL
+
+Example:
+snvs: snvs@020cc000 {
+	compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd";
+	reg = <0x020cc000 0x4000>;
+
+	snvs_lpgpr: snvs-lpgpr {
+		compatible = "fsl,imx6q-snvs-lpgpr";
+	};
+};
diff --git a/Documentation/devicetree/bindings/nvmem/uniphier-efuse.txt b/Documentation/devicetree/bindings/nvmem/uniphier-efuse.txt
new file mode 100644
index 000000000000..eccf490d5a6d
--- /dev/null
+++ b/Documentation/devicetree/bindings/nvmem/uniphier-efuse.txt
@@ -0,0 +1,49 @@
+= UniPhier eFuse device tree bindings =
+
+This UniPhier eFuse must be under soc-glue.
+
+Required properties:
+- compatible: should be "socionext,uniphier-efuse"
+- reg: should contain the register location and length
+
+= Data cells =
+Are child nodes of efuse, bindings of which as described in
+bindings/nvmem/nvmem.txt
+
+Example:
+
+	soc-glue@5f900000 {
+		compatible = "socionext,uniphier-ld20-soc-glue-debug",
+			     "simple-mfd";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x0 0x5f900000 0x2000>;
+
+		efuse@100 {
+			compatible = "socionext,uniphier-efuse";
+			reg = <0x100 0x28>;
+		};
+
+		efuse@200 {
+			compatible = "socionext,uniphier-efuse";
+			reg = <0x200 0x68>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+
+			/* Data cells */
+			usb_mon: usb-mon@54 {
+				reg = <0x54 0xc>;
+			};
+		};
+	};
+
+= Data consumers =
+Are device nodes which consume nvmem data cells.
+
+Example:
+
+	usb {
+		...
+		nvmem-cells = <&usb_mon>;
+		nvmem-cell-names = "usb_mon";
+	}
diff --git a/Documentation/trace/coresight-cpu-debug.txt b/Documentation/trace/coresight-cpu-debug.txt
index b3da1f90b861..2b9b51cd501e 100644
--- a/Documentation/trace/coresight-cpu-debug.txt
+++ b/Documentation/trace/coresight-cpu-debug.txt
@@ -149,11 +149,23 @@ If you want to limit idle states at boot time, you can use "nohlt" or
 
 At the runtime you can disable idle states with below methods:
 
-Set latency request to /dev/cpu_dma_latency to disable all CPUs specific idle
-states (if latency = 0uS then disable all idle states):
-# echo "what_ever_latency_you_need_in_uS" > /dev/cpu_dma_latency
-
-Disable specific CPU's specific idle state:
+It is possible to disable CPU idle states by way of the PM QoS
+subsystem, more specifically by using the "/dev/cpu_dma_latency"
+interface (see Documentation/power/pm_qos_interface.txt for more
+details).  As specified in the PM QoS documentation the requested
+parameter will stay in effect until the file descriptor is released.
+For example:
+
+# exec 3<> /dev/cpu_dma_latency; echo 0 >&3
+...
+Do some work...
+...
+# exec 3<>-
+
+The same can also be done from an application program.
+
+Disable specific CPU's specific idle state from cpuidle sysfs (see
+Documentation/cpuidle/sysfs.txt):
 # echo 1 > /sys/devices/system/cpu/cpu$cpu/cpuidle/state$state/disable
 
 
diff --git a/Documentation/w1/slaves/00-INDEX b/Documentation/w1/slaves/00-INDEX
index 8d76718e1ea2..68946f83e579 100644
--- a/Documentation/w1/slaves/00-INDEX
+++ b/Documentation/w1/slaves/00-INDEX
@@ -10,3 +10,5 @@ w1_ds2438
 	- The Maxim/Dallas Semiconductor ds2438 smart battery monitor.
 w1_ds28e04
 	- The Maxim/Dallas Semiconductor ds28e04 eeprom.
+w1_ds28e17
+	- The Maxim/Dallas Semiconductor ds28e17 1-Wire-to-I2C Master Bridge.
diff --git a/Documentation/w1/slaves/w1_ds28e17 b/Documentation/w1/slaves/w1_ds28e17
new file mode 100644
index 000000000000..7fcfad5b4a37
--- /dev/null
+++ b/Documentation/w1/slaves/w1_ds28e17
@@ -0,0 +1,68 @@
+Kernel driver w1_ds28e17
+========================
+
+Supported chips:
+  * Maxim DS28E17 1-Wire-to-I2C Master Bridge
+
+supported family codes:
+	W1_FAMILY_DS28E17  0x19
+
+Author: Jan Kandziora <jjj@gmx.de>
+
+
+Description
+-----------
+The DS28E17 is a Onewire slave device which acts as an I2C bus master.
+
+This driver creates a new I2C bus for any DS28E17 device detected. I2C buses
+come and go as the DS28E17 devices come and go. I2C slave devices connected to
+a DS28E17 can be accessed by the kernel or userspace tools as if they were
+connected to a "native" I2C bus master.
+
+
+An udev rule like the following
+-------------------------------------------------------------------------------
+SUBSYSTEM=="i2c-dev", KERNEL=="i2c-[0-9]*", ATTRS{name}=="w1-19-*", \
+        SYMLINK+="i2c-$attr{name}"
+-------------------------------------------------------------------------------
+may be used to create stable /dev/i2c- entries based on the unique id of the
+DS28E17 chip.
+
+
+Driver parameters are:
+
+speed:
+	This sets up the default I2C speed a DS28E17 get configured for as soon
+	it is connected. The power-on default	of the DS28E17 is 400kBaud, but
+	chips may come and go on the Onewire bus without being de-powered and
+	as soon the "w1_ds28e17" driver notices a freshly connected, or
+	reconnected DS28E17 device on the Onewire bus, it will re-apply this
+	setting.
+
+	Valid values are 100, 400, 900 [kBaud]. Any other value means to leave
+	alone the current DS28E17 setting on detect. The default value is 100.
+
+stretch:
+	This sets up the default stretch value used for freshly connected
+	DS28E17 devices. It is a multiplier used on the calculation of the busy
+	wait time for an I2C transfer. This is to account for I2C slave devices
+	which make heavy use of the I2C clock stretching feature and thus, the
+	needed timeout cannot be pre-calculated correctly. As the w1_ds28e17
+	driver checks the DS28E17's busy flag in a loop after the precalculated
+	wait time, it should be hardly needed to tweak this setting.
+
+	Leave it at 1 unless you get ETIMEDOUT errors and a "w1_slave_driver
+	19-00000002dbd8: busy timeout" in the kernel log.
+
+	Valid values are 1 to 9. The default is 1.
+
+
+The driver creates sysfs files /sys/bus/w1/devices/19-<id>/speed and
+/sys/bus/w1/devices/19-<id>/stretch for each device, preloaded with the default
+settings from the driver parameters. They may be changed anytime. In addition a
+directory /sys/bus/w1/devices/19-<id>/i2c-<nnn> for the I2C bus master sysfs
+structure is created.
+
+
+See https://github.com/ianka/w1_ds28e17 for even more information.
+