Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC device tree updates from Arnd Bergmann:
 "There are close to 800 indivudal changesets in this branch again,
  which feels like a lot. There are particularly many changes for the
  NVIDIA Tegra platform this time, in fact more than it has seen in the
  two years since the v4.9 merge window. Aside from this, it's been
  fairly normal, with lots of changes going into Renesas R-CAR, NXP
  i.MX, Allwinner Sunxi, Samsung Exynos, and TI OMAP.

  Most of the changes are for adding new features into existing boards,
  for brevity I'm only mentioning completely new machines and SoCs here.
  For the first time I think we have (slightly) more new 64-bit hardware
  than 32-bit:

  Two boards get added for TI OMAP: Moxa UC-2101 is an industrial
  computer, see https://www.moxa.com/product/UC-2100.htm; GTA04A5 is a
  minor variation of the motherboards of the GTA04 phone, see
  https://shop.goldelico.com/wiki.php?page=GTA04A5

  Clearfog is a nice little board for quad-core Marvell Armada 8040
  network processor, see
  https://www.solid-run.com/marvell-armada-family/clearfog-gt-8k/

  Two additional server boards come with the Aspeed baseboard management
  controllers: Stardragon4800 is an arm64 reference platform made by HXT
  (based on Qualcomm's server chips), and TiogaPass is an Open Compute
  mainboard with x86 CPUs. Both use the ARM11 based AST2500 chips in the
  BMC.

  NXP i.MX usually sees a lot of new boards each release. This time
  there we only add one minor variant: ConnectCore 6UL SBC Pro uses the
  same SoM design as the ConnectCore 6UL SBC Express added later.
  However, there is a new chip, the i.MX6ULZ, which is an even smaller
  variant of the i.MX6ULL, with features removed. There is also support
  for the reference board design, the i.MX6ULZ 14x14 EVK.

  A new Raspberry Pi variant gets added, this one is the CM3 compute
  module based on bcm2837, it was launched in early 2017 but only now
  added to the kernel, both as 32-bit and as 64-bit files, as we tend to
  do for Raspberry Pi.

  On the Allwinner side, everything is again about cheap development
  boards, usually of the "Fruit Pi" variety. The new ones this time are:
   - Orange Pi Zero Plus2: http://www.orangepi.org/OrangePiZeroPlus2/
   - Orange Pi One Plus: http://www.orangepi.org/OrangePiOneplus/
   - Pine64 LTS: https://www.pine64.org/?product=pine-a64-lts
   - Banana Pi M2+ H5: http://www.banana-pi.org/m2plus.html
  The last one of these is now a 64-bit version of the earlier Banana Pi
  M2+ H3, with the same board layout.

  Similarly, for Rockchips, get get another variant of the 32-bit Asus
  Tinker board, the model 'S' based on rk3288, and three now boards
  based on the popular RK3399 chip:
   - ROC-RK3399-PC: https://libre.computer/products/boards/roc-rk3399-pc/
   - Rock960: https://www.96boards.org/product/rock960/
   - RockPro64: https://www.pine64.org/?page_id=61454
  These are all quite powerful boards with lots of RAM and I/O, and the
  RK3399 is the same chip used in several Chromebooks. Finally, we get
  support for the PX30 (aka rk3326) chip, which is based on the low-end
  64-bit Cortex-A35 CPU core. So far, only the evaluation board is
  supported.

  One more Banana Pi is added with a Mediatek chip: Banana Pi R64 is
  based on the MT7622 WiFi router platform, and the first product I've
  seen with a 64-bit Mediatek chip in that market:
  http://www.banana-pi.org/r64.html

  For HiSilicon, we gain support for the Hi3670 SoC and HiKey 370
  development board, which are similar to the Hi3660 and Hikey 360
  respectively, but add support for an NPU.

  Amlogic gets initial support for the Meson-G12A chip (S905D2), another
  quad-core Cortex-A53 SoC, and its evaluation platform. On the 32-bit
  side, we gain support for an actual end-user product, the Endless
  Computers Endless Mini based on Meson8b (S805), see
  https://endlessos.com/computers/

  Qualcomm adds support for their MSM8998 SoC and evaluation platform.
  This chip is commonly known as the Snapdragon 835, and is used in
  high-end phones as well as low-end laptops.

  For Renesas, a very bare support for the r8a774a1 (RZ/G2M) is added,
  but no boards for this one. However, we do add boards for the
  previously added r8a77965 (R-Car M3-N): the M3NULCB Kingfisher and the
  M3NULCB Starter Kit Pro.

  While we have lots of DT changes for NVIDIA to update the existing
  files, the only board that gets added is the Toradex Colibri T20 on
  Colibri Evaluation Board for the old Tegra2.

  Synaptics add support for their AS370 SoC, which is part of the
  (formerly Marvell) Berlin line of set-top-box chips used e.g. in the
  various Google Chromecast. Only the .dtsi gets added at this point, no
  actual machines"

* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (721 commits)
  ARM: dts: socfgpa: remove ethernet aliases from dtsi
  arm64: dts: stratix10: add ethernet aliases
  dt-bindings: mediatek: Add bindig for MT7623 IOMMU and SMI
  dt-bindings: mediatek: Add JPEG Decoder binding for MT7623
  dt-bindings: iommu: mediatek: Add binding for MT7623
  dt-bindings: clock: mediatek: add support for MT7623
  ARM: dts: mvebu: armada-385-db-88f6820-amc: auto-detect nand ECC properites
  ARM: dts: da850-lego-ev3: slow down A/DC as much as possible
  ARM: dts: da850-evm: Enable tca6416 on baseboard
  arm64: dts: uniphier: Add USB2 PHY nodes
  arm64: dts: uniphier: Add USB3 controller nodes
  ARM: dts: uniphier: Add USB2 PHY nodes
  ARM: dts: uniphier: Add USB3 controller nodes
  arm64: dts: meson-axg: s400: disable emmc
  arm64: dts: meson-axg: s400: add missing emmc pwrseq
  arm64: dts: clearfog-gt-8k: add PCIe slot description
  ARM: dts: at91: sama5d4_xplained: even nand memory partitions
  ARM: dts: at91: sama5d3_xplained: even nand memory partitions
  ARM: dts: at91: at91sam9x5cm: even nand memory partitions
  ARM: dts: at91: sama5d2_ptc_ek: fix bootloader env offsets
  ...

35 files changed, 385 insertions, 11 deletions

diff --git a/Documentation/arm/Samsung/Bootloader-interface.txt b/Documentation/arm/Samsung/Bootloader-interface.txt
index ed494ac0beb2..d17ed518a7ea 100644
--- a/Documentation/arm/Samsung/Bootloader-interface.txt
+++ b/Documentation/arm/Samsung/Bootloader-interface.txt
@@ -26,6 +26,7 @@ Offset        Value                                        Purpose
 0x20          0xfcba0d10 (Magic cookie)                    AFTR
 0x24          exynos_cpu_resume_ns                         AFTR
 0x28 + 4*cpu  0x8 (Magic cookie, Exynos3250)               AFTR
+0x28          0x0 or last value during resume (Exynos542x) System suspend
 
 
 2. Secure mode
diff --git a/Documentation/devicetree/bindings/arm/amlogic.txt b/Documentation/devicetree/bindings/arm/amlogic.txt
index b5c2b5c35766..4498292b833d 100644
--- a/Documentation/devicetree/bindings/arm/amlogic.txt
+++ b/Documentation/devicetree/bindings/arm/amlogic.txt
@@ -57,12 +57,17 @@ Boards with the Amlogic Meson AXG A113D SoC shall have the following properties:
   Required root node property:
     compatible: "amlogic,a113d", "amlogic,meson-axg";
 
+Boards with the Amlogic Meson G12A S905D2 SoC shall have the following properties:
+  Required root node property:
+    compatible: "amlogic,g12a";
+
 Board compatible values (alphabetically, grouped by SoC):
 
   - "geniatech,atv1200" (Meson6)
 
   - "minix,neo-x8" (Meson8)
 
+  - "endless,ec100" (Meson8b)
   - "hardkernel,odroid-c1" (Meson8b)
   - "tronfy,mxq" (Meson8b)
 
@@ -101,6 +106,8 @@ Board compatible values (alphabetically, grouped by SoC):
 
   - "amlogic,s400" (Meson axg a113d)
 
+  - "amlogic,u200" (Meson g12a s905d2)
+
 Amlogic Meson Firmware registers Interface
 ------------------------------------------
 
diff --git a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
index 1e3e29a545e2..0dcc3ea5adff 100644
--- a/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
+++ b/Documentation/devicetree/bindings/arm/bcm/brcm,bcm2835.txt
@@ -42,6 +42,14 @@ Raspberry Pi Compute Module
 Required root node properties:
 compatible = "raspberrypi,compute-module", "brcm,bcm2835";
 
+Raspberry Pi Compute Module 3
+Required root node properties:
+compatible = "raspberrypi,3-compute-module", "brcm,bcm2837";
+
+Raspberry Pi Compute Module 3 Lite
+Required root node properties:
+compatible = "raspberrypi,3-compute-module-lite", "brcm,bcm2837";
+
 Raspberry Pi Zero
 Required root node properties:
 compatible = "raspberrypi,model-zero", "brcm,bcm2835";
diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
index 1e775aaa5c5b..5074aeecd327 100644
--- a/Documentation/devicetree/bindings/arm/fsl.txt
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -57,6 +57,50 @@ i.MX6SLL EVK board
 Required root node properties:
     - compatible = "fsl,imx6sll-evk", "fsl,imx6sll";
 
+i.MX6 Quad Plus SABRE Smart Device Board
+Required root node properties:
+    - compatible = "fsl,imx6qp-sabresd", "fsl,imx6qp";
+
+i.MX6 Quad Plus SABRE Automotive Board
+Required root node properties:
+    - compatible = "fsl,imx6qp-sabreauto", "fsl,imx6qp";
+
+i.MX6 DualLite SABRE Smart Device Board
+Required root node properties:
+    - compatible = "fsl,imx6dl-sabresd", "fsl,imx6dl";
+
+i.MX6 DualLite/Solo SABRE Automotive Board
+Required root node properties:
+    - compatible = "fsl,imx6dl-sabreauto", "fsl,imx6dl";
+
+i.MX6 SoloLite EVK Board
+Required root node properties:
+    - compatible = "fsl,imx6sl-evk", "fsl,imx6sl";
+
+i.MX6 UltraLite 14x14 EVK Board
+Required root node properties:
+    - compatible = "fsl,imx6ul-14x14-evk", "fsl,imx6ul";
+
+i.MX6 UltraLiteLite 14x14 EVK Board
+Required root node properties:
+    - compatible = "fsl,imx6ull-14x14-evk", "fsl,imx6ull";
+
+i.MX6 ULZ 14x14 EVK Board
+Required root node properties:
+    - compatible = "fsl,imx6ulz-14x14-evk", "fsl,imx6ull", "fsl,imx6ulz";
+
+i.MX6 SoloX SDB Board
+Required root node properties:
+    - compatible = "fsl,imx6sx-sdb", "fsl,imx6sx";
+
+i.MX6 SoloX Sabre Auto Board
+Required root node properties:
+    - compatible = "fsl,imx6sx-sabreauto", "fsl,imx6sx";
+
+i.MX7 SabreSD Board
+Required root node properties:
+    - compatible = "fsl,imx7d-sdb", "fsl,imx7d";
+
 Generic i.MX boards
 -------------------
 
diff --git a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
index 199cd36fe1ba..a97f643e7d1c 100644
--- a/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
+++ b/Documentation/devicetree/bindings/arm/hisilicon/hisilicon.txt
@@ -8,6 +8,14 @@ HiKey960 Board
 Required root node properties:
 	- compatible = "hisilicon,hi3660-hikey960", "hisilicon,hi3660";
 
+Hi3670 SoC
+Required root node properties:
+	- compatible = "hisilicon,hi3670";
+
+HiKey970 Board
+Required root node properties:
+	- compatible = "hisilicon,hi3670-hikey970", "hisilicon,hi3670";
+
 Hi3798cv200 SoC
 Required root node properties:
 	- compatible = "hisilicon,hi3798cv200";
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
index b404d592ce58..4e4a3c0ab9ab 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,apmixedsys.txt
@@ -10,6 +10,7 @@ Required Properties:
 	- "mediatek,mt2712-apmixedsys", "syscon"
 	- "mediatek,mt6797-apmixedsys"
 	- "mediatek,mt7622-apmixedsys"
+	- "mediatek,mt7623-apmixedsys", "mediatek,mt2701-apmixedsys"
 	- "mediatek,mt8135-apmixedsys"
 	- "mediatek,mt8173-apmixedsys"
 - #clock-cells: Must be 1
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt
index 34a69ba67f13..d1606b2c3e63 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,audsys.txt
@@ -8,6 +8,7 @@ Required Properties:
 - compatible: Should be one of:
 	- "mediatek,mt2701-audsys", "syscon"
 	- "mediatek,mt7622-audsys", "syscon"
+	- "mediatek,mt7623-audsys", "mediatek,mt2701-audsys", "syscon"
 - #clock-cells: Must be 1
 
 The AUDSYS controller uses the common clk binding from
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
index 4010e37c53a0..149567a38215 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,bdpsys.txt
@@ -8,6 +8,7 @@ Required Properties:
 - compatible: Should be:
 	- "mediatek,mt2701-bdpsys", "syscon"
 	- "mediatek,mt2712-bdpsys", "syscon"
+	- "mediatek,mt7623-bdpsys", "mediatek,mt2701-bdpsys", "syscon"
 - #clock-cells: Must be 1
 
 The bdpsys controller uses the common clk binding from
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt
index 8f5335b480ac..f17cfe64255d 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,ethsys.txt
@@ -8,6 +8,7 @@ Required Properties:
 - compatible: Should be:
 	- "mediatek,mt2701-ethsys", "syscon"
 	- "mediatek,mt7622-ethsys", "syscon"
+	- "mediatek,mt7623-ethsys", "mediatek,mt2701-ethsys", "syscon"
 - #clock-cells: Must be 1
 - #reset-cells: Must be 1
 
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt
index f5629d64cef2..323905af82c3 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,hifsys.txt
@@ -9,6 +9,7 @@ Required Properties:
 - compatible: Should be:
 	- "mediatek,mt2701-hifsys", "syscon"
 	- "mediatek,mt7622-hifsys", "syscon"
+	- "mediatek,mt7623-hifsys", "mediatek,mt2701-hifsys", "syscon"
 - #clock-cells: Must be 1
 
 The hifsys controller uses the common clk binding from
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt
index 868bd51a98be..3f99672163e3 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,imgsys.txt
@@ -9,6 +9,7 @@ Required Properties:
 	- "mediatek,mt2701-imgsys", "syscon"
 	- "mediatek,mt2712-imgsys", "syscon"
 	- "mediatek,mt6797-imgsys", "syscon"
+	- "mediatek,mt7623-imgsys", "mediatek,mt2701-imgsys", "syscon"
 	- "mediatek,mt8173-imgsys", "syscon"
 - #clock-cells: Must be 1
 
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt
index 566f153f9f83..89f4272a1441 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,infracfg.txt
@@ -11,6 +11,7 @@ Required Properties:
 	- "mediatek,mt2712-infracfg", "syscon"
 	- "mediatek,mt6797-infracfg", "syscon"
 	- "mediatek,mt7622-infracfg", "syscon"
+	- "mediatek,mt7623-infracfg", "mediatek,mt2701-infracfg", "syscon"
 	- "mediatek,mt8135-infracfg", "syscon"
 	- "mediatek,mt8173-infracfg", "syscon"
 - #clock-cells: Must be 1
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt
index 4eb8bbe15c01..15d977afad31 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt
@@ -9,6 +9,7 @@ Required Properties:
 	- "mediatek,mt2701-mmsys", "syscon"
 	- "mediatek,mt2712-mmsys", "syscon"
 	- "mediatek,mt6797-mmsys", "syscon"
+	- "mediatek,mt7623-mmsys", "mediatek,mt2701-mmsys", "syscon"
 	- "mediatek,mt8173-mmsys", "syscon"
 - #clock-cells: Must be 1
 
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt
index fb58ca8c2770..6755514deb80 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,pericfg.txt
@@ -10,6 +10,7 @@ Required Properties:
 	- "mediatek,mt2701-pericfg", "syscon"
 	- "mediatek,mt2712-pericfg", "syscon"
 	- "mediatek,mt7622-pericfg", "syscon"
+	- "mediatek,mt7623-pericfg", "mediatek,mt2701-pericfg", "syscon"
 	- "mediatek,mt8135-pericfg", "syscon"
 	- "mediatek,mt8173-pericfg", "syscon"
 - #clock-cells: Must be 1
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt
index 24014a7e2332..d849465b8c99 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,topckgen.txt
@@ -10,6 +10,7 @@ Required Properties:
 	- "mediatek,mt2712-topckgen", "syscon"
 	- "mediatek,mt6797-topckgen"
 	- "mediatek,mt7622-topckgen"
+	- "mediatek,mt7623-topckgen", "mediatek,mt2701-topckgen"
 	- "mediatek,mt8135-topckgen"
 	- "mediatek,mt8173-topckgen"
 - #clock-cells: Must be 1
diff --git a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt
index ea40d05089f8..3212afc753c8 100644
--- a/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt
+++ b/Documentation/devicetree/bindings/arm/mediatek/mediatek,vdecsys.txt
@@ -9,6 +9,7 @@ Required Properties:
 	- "mediatek,mt2701-vdecsys", "syscon"
 	- "mediatek,mt2712-vdecsys", "syscon"
 	- "mediatek,mt6797-vdecsys", "syscon"
+	- "mediatek,mt7623-vdecsys", "mediatek,mt2701-vdecsys", "syscon"
 	- "mediatek,mt8173-vdecsys", "syscon"
 - #clock-cells: Must be 1
 
diff --git a/Documentation/devicetree/bindings/arm/rockchip.txt b/Documentation/devicetree/bindings/arm/rockchip.txt
index acfd3c773dd0..0cc71236d639 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.txt
+++ b/Documentation/devicetree/bindings/arm/rockchip.txt
@@ -5,6 +5,10 @@ Rockchip platforms device tree bindings
     Required root node properties:
       - compatible = "vamrs,ficus", "rockchip,rk3399";
 
+- 96boards RK3399 Rock960 (ROCK960 Consumer Edition)
+    Required root node properties:
+      - compatible = "vamrs,rock960", "rockchip,rk3399";
+
 - Amarula Vyasa RK3288 board
     Required root node properties:
       - compatible = "amarula,vyasa-rk3288", "rockchip,rk3288";
@@ -13,6 +17,10 @@ Rockchip platforms device tree bindings
     Required root node properties:
       - compatible = "asus,rk3288-tinker", "rockchip,rk3288";
 
+- Asus Tinker board S
+    Required root node properties:
+      - compatible = "asus,rk3288-tinker-s", "rockchip,rk3288";
+
 - Kylin RK3036 board:
     Required root node properties:
       - compatible = "rockchip,kylin-rk3036", "rockchip,rk3036";
@@ -59,6 +67,10 @@ Rockchip platforms device tree bindings
     Required root node properties:
       - compatible = "firefly,roc-rk3328-cc", "rockchip,rk3328";
 
+- Firefly ROC-RK3399-PC board:
+    Required root node properties:
+      - compatible = "firefly,roc-rk3399-pc", "rockchip,rk3399";
+
 - ChipSPARK PopMetal-RK3288 board:
     Required root node properties:
       - compatible = "chipspark,popmetal-rk3288", "rockchip,rk3288";
@@ -160,6 +172,10 @@ Rockchip platforms device tree bindings
     Required root node properties:
     - compatible = "pine64,rock64", "rockchip,rk3328";
 
+- Pine64 RockPro64 board:
+    Required root node properties:
+    - compatible = "pine64,rockpro64", "rockchip,rk3399";
+
 - Rockchip PX3 Evaluation board:
     Required root node properties:
       - compatible = "rockchip,px3-evb", "rockchip,px3", "rockchip,rk3188";
@@ -168,6 +184,10 @@ Rockchip platforms device tree bindings
     Required root node properties:
       - compatible = "rockchip,px5-evb", "rockchip,px5", "rockchip,rk3368";
 
+- Rockchip PX30 Evaluation board:
+    Required root node properties:
+      - compatible = "rockchip,px30-evb", "rockchip,px30";
+
 - Rockchip RV1108 Evaluation board
     Required root node properties:
       - compatible = "rockchip,rv1108-evb", "rockchip,rv1108";
diff --git a/Documentation/devicetree/bindings/arm/scu.txt b/Documentation/devicetree/bindings/arm/scu.txt
index 08a587875996..74d0a780ce51 100644
--- a/Documentation/devicetree/bindings/arm/scu.txt
+++ b/Documentation/devicetree/bindings/arm/scu.txt
@@ -22,7 +22,7 @@ References:
 
 Example:
 
-scu@a04100000 {
+scu@a0410000 {
 	compatible = "arm,cortex-a9-scu";
 	reg = <0xa0410000 0x100>;
 };
diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt
index 89b4a389fbc7..f5e0f82fd503 100644
--- a/Documentation/devicetree/bindings/arm/shmobile.txt
+++ b/Documentation/devicetree/bindings/arm/shmobile.txt
@@ -7,6 +7,8 @@ SoCs:
     compatible = "renesas,emev2"
   - RZ/A1H (R7S72100)
     compatible = "renesas,r7s72100"
+  - RZ/A2 (R7S9210)
+    compatible = "renesas,r7s9210"
   - SH-Mobile AG5 (R8A73A00/SH73A0)
     compatible = "renesas,sh73a0"
   - R-Mobile APE6 (R8A73A40)
@@ -23,6 +25,10 @@ SoCs:
     compatible = "renesas,r8a7745"
   - RZ/G1C (R8A77470)
     compatible = "renesas,r8a77470"
+  - RZ/G2M (R8A774A1)
+    compatible = "renesas,r8a774a1"
+  - RZ/G2E (RA8774C0)
+    compatible = "renesas,r8a774c0"
   - R-Car M1A (R8A77781)
     compatible = "renesas,r8a7778"
   - R-Car H1 (R8A77790)
@@ -107,6 +113,8 @@ Boards:
     compatible = "renesas,lager", "renesas,r8a7790"
   - M3ULCB (R-Car Starter Kit Pro, RTP0RC7796SKBX0010SA09 (M3 ES1.0))
     compatible = "renesas,m3ulcb", "renesas,r8a7796"
+  - M3NULCB (R-Car Starter Kit Pro, RTP0RC77965SKBX010SA00 (M3-N ES1.1))
+    compatible = "renesas,m3nulcb", "renesas,r8a77965"
   - Marzen (R0P7779A00010S)
     compatible = "renesas,marzen", "renesas,r8a7779"
   - Porter (M2-LCDP)
@@ -143,12 +151,12 @@ Boards:
     compatible = "renesas,wheat", "renesas,r8a7792"
 
 
-Most Renesas ARM SoCs have a Product Register that allows to retrieve SoC
-product and revision information.  If present, a device node for this register
-should be added.
+Most Renesas ARM SoCs have a Product Register or Boundary Scan ID Register that
+allows to retrieve SoC product and revision information.  If present, a device
+node for this register should be added.
 
 Required properties:
-  - compatible: Must be "renesas,prr".
+  - compatible: Must be "renesas,prr" or "renesas,bsid"
   - reg: Base address and length of the register block.
 
 
diff --git a/Documentation/devicetree/bindings/arm/marvell/marvell,berlin.txt b/Documentation/devicetree/bindings/arm/syna.txt
index 3bab18409b7a..2face46a5f64 100644
--- a/Documentation/devicetree/bindings/arm/marvell/marvell,berlin.txt
+++ b/Documentation/devicetree/bindings/arm/syna.txt
@@ -1,4 +1,9 @@
-Marvell Berlin SoC Family Device Tree Bindings
+Synaptics SoC Device Tree Bindings
+
+According to https://www.synaptics.com/company/news/conexant-marvell
+Synaptics has acquired the Multimedia Solutions Business of Marvell, so
+berlin SoCs are now Synaptics' SoCs now.
+
 ---------------------------------------------------------------
 
 Work in progress statement:
@@ -13,6 +18,10 @@ stable binding/ABI.
 
 ---------------------------------------------------------------
 
+Boards with the Synaptics AS370 SoC shall have the following properties:
+  Required root node property:
+    compatible: "syna,as370"
+
 Boards with a SoC of the Marvell Berlin family, e.g. Armada 1500
 shall have the following properties:
 
diff --git a/Documentation/devicetree/bindings/arm/tegra.txt b/Documentation/devicetree/bindings/arm/tegra.txt
index 32f62bb7006d..c59b15f64346 100644
--- a/Documentation/devicetree/bindings/arm/tegra.txt
+++ b/Documentation/devicetree/bindings/arm/tegra.txt
@@ -47,12 +47,17 @@ board-specific compatible values:
   nvidia,ventana
   toradex,apalis_t30
   toradex,apalis_t30-eval
+  toradex,apalis_t30-v1.1
+  toradex,apalis_t30-v1.1-eval
   toradex,apalis-tk1
   toradex,apalis-tk1-eval
-  toradex,colibri_t20-512
+  toradex,apalis-tk1-v1.2
+  toradex,apalis-tk1-v1.2-eval
+  toradex,colibri_t20
+  toradex,colibri_t20-eval-v3
+  toradex,colibri_t20-iris
   toradex,colibri_t30
   toradex,colibri_t30-eval-v3
-  toradex,iris
 
 Trusted Foundations
 -------------------------------------------
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
index 5a3bf7c5a7a0..c9fd6d1de57e 100644
--- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
@@ -34,3 +34,96 @@ Board DTS:
 	pmc@c360000 {
 		nvidia,invert-interrupt;
 	};
+
+== Pad Control ==
+
+On Tegra SoCs a pad is a set of pins which are configured as a group.
+The pin grouping is a fixed attribute of the hardware. The PMC can be
+used to set pad power state and signaling voltage. A pad can be either
+in active or power down mode. The support for power state and signaling
+voltage configuration varies depending on the pad in question. 3.3 V and
+1.8 V signaling voltages are supported on pins where software
+controllable signaling voltage switching is available.
+
+Pad configurations are described with pin configuration nodes which
+are placed under the pmc node and they are referred to by the pinctrl
+client properties. For more information see
+Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
+
+The following pads are present on Tegra186:
+csia		csib		dsi		mipi-bias
+pex-clk-bias	pex-clk3	pex-clk2	pex-clk1
+usb0		usb1		usb2		usb-bias
+uart		audio		hsic		dbg
+hdmi-dp0	hdmi-dp1	pex-cntrl	sdmmc2-hv
+sdmmc4		cam		dsib		dsic
+dsid		csic		csid		csie
+dsif		spi		ufs		dmic-hv
+edp		sdmmc1-hv	sdmmc3-hv	conn
+audio-hv	ao-hv
+
+Required pin configuration properties:
+  - pins: A list of strings, each of which contains the name of a pad
+	  to be configured.
+
+Optional pin configuration properties:
+  - low-power-enable: Configure the pad into power down mode
+  - low-power-disable: Configure the pad into active mode
+  - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or
+    TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
+    The values are defined in
+    include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
+
+Note: The power state can be configured on all of the above pads except
+      for ao-hv. Following pads have software configurable signaling
+      voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv, audio-hv,
+      ao-hv.
+
+Pad configuration state example:
+	pmc: pmc@7000e400 {
+		compatible = "nvidia,tegra186-pmc";
+		reg = <0 0x0c360000 0 0x10000>,
+		      <0 0x0c370000 0 0x10000>,
+		      <0 0x0c380000 0 0x10000>,
+		      <0 0x0c390000 0 0x10000>;
+		reg-names = "pmc", "wake", "aotag", "scratch";
+
+		...
+
+		sdmmc1_3v3: sdmmc1-3v3 {
+			pins = "sdmmc1-hv";
+			power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
+		};
+
+		sdmmc1_1v8: sdmmc1-1v8 {
+			pins = "sdmmc1-hv";
+			power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
+		};
+
+		hdmi_off: hdmi-off {
+			pins = "hdmi";
+			low-power-enable;
+		}
+
+		hdmi_on: hdmi-on {
+			pins = "hdmi";
+			low-power-disable;
+		}
+	};
+
+Pinctrl client example:
+	sdmmc1: sdhci@3400000 {
+		...
+		pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+		pinctrl-0 = <&sdmmc1_3v3>;
+		pinctrl-1 = <&sdmmc1_1v8>;
+	};
+
+	...
+
+	sor0: sor@15540000 {
+		...
+		pinctrl-0 = <&hdmi_off>;
+		pinctrl-1 = <&hdmi_on>;
+		pinctrl-names = "hdmi-on", "hdmi-off";
+	};
diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
index a74b37b07e5c..cb12f33a247f 100644
--- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
+++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
@@ -195,3 +195,106 @@ Example:
 		power-domains = <&pd_audio>;
 		...
 	};
+
+== Pad Control ==
+
+On Tegra SoCs a pad is a set of pins which are configured as a group.
+The pin grouping is a fixed attribute of the hardware. The PMC can be
+used to set pad power state and signaling voltage. A pad can be either
+in active or power down mode. The support for power state and signaling
+voltage configuration varies depending on the pad in question. 3.3 V and
+1.8 V signaling voltages are supported on pins where software
+controllable signaling voltage switching is available.
+
+The pad configuration state nodes are placed under the pmc node and they
+are referred to by the pinctrl client properties. For more information
+see Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
+The pad name should be used as the value of the pins property in pin
+configuration nodes.
+
+The following pads are present on Tegra124 and Tegra132:
+audio		bb		cam		comp
+csia		csb		cse		dsi
+dsib		dsic		dsid		hdmi
+hsic		hv		lvds		mipi-bias
+nand		pex-bias	pex-clk1	pex-clk2
+pex-cntrl	sdmmc1		sdmmc3		sdmmc4
+sys_ddc		uart		usb0		usb1
+usb2		usb_bias
+
+The following pads are present on Tegra210:
+audio		audio-hv	cam		csia
+csib		csic		csid		csie
+csif		dbg		debug-nonao	dmic
+dp		dsi		dsib		dsic
+dsid		emmc		emmc2		gpio
+hdmi		hsic		lvds		mipi-bias
+pex-bias	pex-clk1	pex-clk2	pex-cntrl
+sdmmc1		sdmmc3		spi		spi-hv
+uart		usb0		usb1		usb2
+usb3		usb-bias
+
+Required pin configuration properties:
+  - pins: Must contain name of the pad(s) to be configured.
+
+Optional pin configuration properties:
+  - low-power-enable: Configure the pad into power down mode
+  - low-power-disable: Configure the pad into active mode
+  - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8
+    or TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
+    The values are defined in
+    include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
+
+Note: The power state can be configured on all of the Tegra124 and
+      Tegra132 pads. None of the Tegra124 or Tegra132 pads support
+      signaling voltage switching.
+
+Note: All of the listed Tegra210 pads except pex-cntrl support power
+      state configuration. Signaling voltage switching is supported on
+      following Tegra210 pads: audio, audio-hv, cam, dbg, dmic, gpio,
+      pex-cntrl, sdmmc1, sdmmc3, spi, spi-hv, and uart.
+
+Pad configuration state example:
+	pmc: pmc@7000e400 {
+		compatible = "nvidia,tegra210-pmc";
+		reg = <0x0 0x7000e400 0x0 0x400>;
+		clocks = <&tegra_car TEGRA210_CLK_PCLK>, <&clk32k_in>;
+		clock-names = "pclk", "clk32k_in";
+
+		...
+
+		sdmmc1_3v3: sdmmc1-3v3 {
+			pins = "sdmmc1";
+			power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
+		};
+
+		sdmmc1_1v8: sdmmc1-1v8 {
+			pins = "sdmmc1";
+			power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
+		};
+
+		hdmi_off: hdmi-off {
+			pins = "hdmi";
+			low-power-enable;
+		}
+
+		hdmi_on: hdmi-on {
+			pins = "hdmi";
+			low-power-disable;
+		}
+	};
+
+Pinctrl client example:
+	sdmmc1: sdhci@700b0000 {
+		...
+		pinctrl-names = "sdmmc-3v3", "sdmmc-1v8";
+		pinctrl-0 = <&sdmmc1_3v3>;
+		pinctrl-1 = <&sdmmc1_1v8>;
+	};
+	...
+	sor@54540000 {
+		...
+		pinctrl-0 = <&hdmi_off>;
+		pinctrl-1 = <&hdmi_on>;
+		pinctrl-names = "hdmi-on", "hdmi-off";
+	};
diff --git a/Documentation/devicetree/bindings/arm/ux500/boards.txt b/Documentation/devicetree/bindings/arm/ux500/boards.txt
index 0fa429534f49..89408de55bfd 100644
--- a/Documentation/devicetree/bindings/arm/ux500/boards.txt
+++ b/Documentation/devicetree/bindings/arm/ux500/boards.txt
@@ -60,7 +60,7 @@ Example:
 			      <0xa0410100 0x100>;
 		};
 
-		scu@a04100000 {
+		scu@a0410000 {
 			compatible = "arm,cortex-a9-scu";
 			reg = <0xa0410000 0x100>;
 		};
diff --git a/Documentation/devicetree/bindings/clock/imx6q-clock.txt b/Documentation/devicetree/bindings/clock/imx6q-clock.txt
index a45ca67a9d5f..e1308346e00d 100644
--- a/Documentation/devicetree/bindings/clock/imx6q-clock.txt
+++ b/Documentation/devicetree/bindings/clock/imx6q-clock.txt
@@ -6,6 +6,14 @@ Required properties:
 - interrupts: Should contain CCM interrupt
 - #clock-cells: Should be <1>
 
+Optional properties:
+- fsl,pmic-stby-poweroff: Configure CCM to assert PMIC_STBY_REQ signal
+  on power off.
+  Use this property if the SoC should be powered off by external power
+  management IC (PMIC) triggered via PMIC_STBY_REQ signal.
+  Boards that are designed to initiate poweroff on PMIC_ON_REQ signal should
+  be using "syscon-poweroff" driver instead.
+
 The clock consumer should specify the desired clock by having the clock
 ID in its "clocks" phandle cell.  See include/dt-bindings/clock/imx6qdl-clock.h
 for the full list of i.MX6 Quad and DualLite clock IDs.
diff --git a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt
index df5db732138d..6922db598def 100644
--- a/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt
+++ b/Documentation/devicetree/bindings/iommu/mediatek,iommu.txt
@@ -41,6 +41,8 @@ Required properties:
 - compatible : must be one of the following string:
 	"mediatek,mt2701-m4u" for mt2701 which uses generation one m4u HW.
 	"mediatek,mt2712-m4u" for mt2712 which uses generation two m4u HW.
+	"mediatek,mt7623-m4u", "mediatek,mt2701-m4u" for mt7623 which uses
+						     generation one m4u HW.
 	"mediatek,mt8173-m4u" for mt8173 which uses generation two m4u HW.
 - reg : m4u register base and size.
 - interrupts : the interrupt of m4u.
@@ -51,7 +53,7 @@ Required properties:
 	according to the local arbiter index, like larb0, larb1, larb2...
 - iommu-cells : must be 1. This is the mtk_m4u_id according to the HW.
 	Specifies the mtk_m4u_id as defined in
-	dt-binding/memory/mt2701-larb-port.h for mt2701,
+	dt-binding/memory/mt2701-larb-port.h for mt2701, mt7623
 	dt-binding/memory/mt2712-larb-port.h for mt2712, and
 	dt-binding/memory/mt8173-larb-port.h for mt8173.
 
diff --git a/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt b/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt
index 3813947b4d4f..044b11913c49 100644
--- a/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt
+++ b/Documentation/devicetree/bindings/media/mediatek-jpeg-decoder.txt
@@ -5,6 +5,7 @@ Mediatek JPEG Decoder is the JPEG decode hardware present in Mediatek SoCs
 Required properties:
 - compatible : must be one of the following string:
 	"mediatek,mt8173-jpgdec"
+	"mediatek,mt7623-jpgdec", "mediatek,mt2701-jpgdec"
 	"mediatek,mt2701-jpgdec"
 - reg : physical base address of the jpeg decoder registers and length of
   memory mapped region.
diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt
index 615abdd0eb0d..e937ddd871a6 100644
--- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt
+++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-common.txt
@@ -17,6 +17,7 @@ Required properties:
 - compatible : must be one of :
 	"mediatek,mt2701-smi-common"
 	"mediatek,mt2712-smi-common"
+	"mediatek,mt7623-smi-common", "mediatek,mt2701-smi-common"
 	"mediatek,mt8173-smi-common"
 - reg : the register and size of the SMI block.
 - power-domains : a phandle to the power domain of this local arbiter.
diff --git a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
index 083155cdc2a0..94eddcae77ab 100644
--- a/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
+++ b/Documentation/devicetree/bindings/memory-controllers/mediatek,smi-larb.txt
@@ -6,6 +6,7 @@ Required properties:
 - compatible : must be one of :
 		"mediatek,mt2701-smi-larb"
 		"mediatek,mt2712-smi-larb"
+		"mediatek,mt7623-smi-larb", "mediatek,mt2701-smi-larb"
 		"mediatek,mt8173-smi-larb"
 - reg : the register and size of this local arbiter.
 - mediatek,smi : a phandle to the smi_common node.
@@ -16,7 +17,7 @@ Required properties:
 	    the register.
   - "smi" : It's the clock for transfer data and command.
 
-Required property for mt2701 and mt2712:
+Required property for mt2701, mt2712 and mt7623:
 - mediatek,larb-id :the hardware id of this larb.
 
 Example:
diff --git a/Documentation/devicetree/bindings/net/dsa/b53.txt b/Documentation/devicetree/bindings/net/dsa/b53.txt
index 1811e1972a7a..5201bc15fdd6 100644
--- a/Documentation/devicetree/bindings/net/dsa/b53.txt
+++ b/Documentation/devicetree/bindings/net/dsa/b53.txt
@@ -46,6 +46,42 @@ Required properties:
       "brcm,bcm6328-switch"
       "brcm,bcm6368-switch" and the mandatory "brcm,bcm63xx-switch"
 
+Required properties for BCM585xx/586xx/88312 SoCs:
+
+ - reg: a total of 3 register base addresses, the first one must be the
+   Switch Register Access block base, the second is the port 5/4 mux
+   configuration register and the third one is the SGMII configuration
+   and status register base address.
+
+ - interrupts: a total of 13 interrupts must be specified, in the following
+   order: port 0-5, 7-8 link status change, then the integrated PHY interrupt,
+   then the timestamping interrupt and the sleep timer interrupts for ports
+   5,7,8.
+
+Optional properties for BCM585xx/586xx/88312 SoCs:
+
+  - reg-names: a total of 3 names matching the 3 base register address, must
+    be in the following order:
+	"srab"
+	"mux_config"
+	"sgmii_config"
+
+  - interrupt-names: a total of 13 names matching the 13 interrupts specified
+    must be in the following order:
+	"link_state_p0"
+	"link_state_p1"
+	"link_state_p2"
+	"link_state_p3"
+	"link_state_p4"
+	"link_state_p5"
+	"link_state_p7"
+	"link_state_p8"
+	"phy"
+	"ts"
+	"imp_sleep_timer_p5"
+	"imp_sleep_timer_p7"
+	"imp_sleep_timer_p8"
+
 See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional
 required and optional properties.
 
diff --git a/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt b/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt
index e319fe5e205a..99c4ba6a3f61 100644
--- a/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt
+++ b/Documentation/devicetree/bindings/nvmem/allwinner,sunxi-sid.txt
@@ -7,6 +7,7 @@ Required properties:
   "allwinner,sun8i-a83t-sid"
   "allwinner,sun8i-h3-sid"
   "allwinner,sun50i-a64-sid"
+  "allwinner,sun50i-h5-sid"
 
 - reg: Should contain registers location and length
 
diff --git a/Documentation/devicetree/bindings/power/actions,owl-sps.txt b/Documentation/devicetree/bindings/power/actions,owl-sps.txt
index 78edd63641e8..a3571937b019 100644
--- a/Documentation/devicetree/bindings/power/actions,owl-sps.txt
+++ b/Documentation/devicetree/bindings/power/actions,owl-sps.txt
@@ -3,11 +3,13 @@ Actions Semi Owl Smart Power System (SPS)
 Required properties:
 - compatible          :  "actions,s500-sps" for S500
                          "actions,s700-sps" for S700
+                         "actions,s900-sps" for S900
 - reg                 :  Offset and length of the register set for the device.
 - #power-domain-cells :  Must be 1.
                          See macros in:
                           include/dt-bindings/power/owl-s500-powergate.h for S500
                           include/dt-bindings/power/owl-s700-powergate.h for S700
+                          include/dt-bindings/power/owl-s900-powergate.h for S900
 
 
 Example:
diff --git a/Documentation/devicetree/bindings/soc/rockchip/grf.txt b/Documentation/devicetree/bindings/soc/rockchip/grf.txt
index 7dc5ce858a0e..46e27cd69f18 100644
--- a/Documentation/devicetree/bindings/soc/rockchip/grf.txt
+++ b/Documentation/devicetree/bindings/soc/rockchip/grf.txt
@@ -13,6 +13,7 @@ On RK3328 SoCs, the GRF adds a section for USB2PHYGRF,
 Required Properties:
 
 - compatible: GRF should be one of the following:
+   - "rockchip,px30-grf", "syscon": for px30
    - "rockchip,rk3036-grf", "syscon": for rk3036
    - "rockchip,rk3066-grf", "syscon": for rk3066
    - "rockchip,rk3188-grf", "syscon": for rk3188
@@ -23,6 +24,7 @@ Required Properties:
    - "rockchip,rk3399-grf", "syscon": for rk3399
    - "rockchip,rv1108-grf", "syscon": for rv1108
 - compatible: PMUGRF should be one of the following:
+   - "rockchip,px30-pmugrf", "syscon": for px30
    - "rockchip,rk3368-pmugrf", "syscon": for rk3368
    - "rockchip,rk3399-pmugrf", "syscon": for rk3399
 - compatible: SGRF should be one of the following
diff --git a/Documentation/devicetree/bindings/usb/dwc2.txt b/Documentation/devicetree/bindings/usb/dwc2.txt
index 46da5f184460..6dc3c4a34483 100644
--- a/Documentation/devicetree/bindings/usb/dwc2.txt
+++ b/Documentation/devicetree/bindings/usb/dwc2.txt
@@ -6,6 +6,7 @@ Required properties:
   - brcm,bcm2835-usb: The DWC2 USB controller instance in the BCM2835 SoC.
   - hisilicon,hi6220-usb: The DWC2 USB controller instance in the hi6220 SoC.
   - rockchip,rk3066-usb: The DWC2 USB controller instance in the rk3066 Soc;
+  - "rockchip,px30-usb", "rockchip,rk3066-usb", "snps,dwc2": for px30 Soc;
   - "rockchip,rk3188-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3188 Soc;
   - "rockchip,rk3288-usb", "rockchip,rk3066-usb", "snps,dwc2": for rk3288 Soc;
   - "lantiq,arx100-usb": The DWC2 USB controller instance in Lantiq ARX SoCs;
diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt
index 14818137a029..4b1a2a8fcc16 100644
--- a/Documentation/devicetree/bindings/vendor-prefixes.txt
+++ b/Documentation/devicetree/bindings/vendor-prefixes.txt
@@ -115,6 +115,7 @@ elan	Elan Microelectronic Corp.
 embest	Shenzhen Embest Technology Co., Ltd.
 emmicro	EM Microelectronic
 emtrion	emtrion GmbH
+endless	Endless Mobile, Inc.
 energymicro	Silicon Laboratories (formerly Energy Micro AS)
 engicam	Engicam S.r.l.
 epcos	EPCOS AG
@@ -301,6 +302,7 @@ pine64	Pine64
 pixcir  PIXCIR MICROELECTRONICS Co., Ltd
 plathome	Plat'Home Co., Ltd.
 plda	PLDA
+plx	Broadcom Corporation (formerly PLX Technology)
 portwell	Portwell Inc.
 poslab	Poslab Technology Co., Ltd.
 powervr	PowerVR (deprecated, use img)