Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:

 - update the ili210x touchscreen driver, refreshing the code and adding
   support for ILI251X line

 - add support for st1633 to the st1232 touchscreen driver

 - add support for sx8650 to the the sx8654 touchscreen driver

 - add support for Evervision FT5726 to the edt-ft5x06 touchscreen
   driver

 - add support for gt5688 to the Goodix touchscreen driver

 - new vibrator driver for MSM SOCs

 - miscellaneous fixes for the rest of input drivers

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (53 commits)
  Input: wacom_serial4 - add support for Wacom ArtPad II tablet
  Input: elan_i2c - add id for touchpad found in Lenovo s21e-20
  Input: raspberrypi-ts - select CONFIG_INPUT_POLLDEV
  Input: msm-vibrator - use correct gpio header
  Input: ti_am335x_tsc - remove set but not used variable 'tscadc_dev'
  Input: i8042 - rework DT node name comparisons
  Input: goodix - print values in case of inconsistencies
  Input: goodix - refer to touchscreen.txt in device tree bindings
  Input: goodix - support Goodix gt5688
  Input: synaptics_i2c - remove redundant spinlock
  Input: db9 - mark expected switch fall-through
  Input: qt2160 - remove redundant spinlock
  Input: st1232 - handle common DT bindings
  Input: ims-pcu - switch to using brightness_set_blocking()
  Input: st1232 - switch to gpiod API
  Input: ili210x - fetch touchscreen geometry from DT
  Input: msm-vibrator - tweak an error message
  Input: tm2-touchkey - acknowledge that setting brightness is a blocking call
  Input: stmfts - acknowledge that setting brightness is a blocking call
  Input: ili210x - switch to using devm_device_add_group()
  ...

7 files changed, 105 insertions, 10 deletions

diff --git a/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt b/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt
index 0c252d9306da..ef2ae729718f 100644
--- a/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt
+++ b/Documentation/devicetree/bindings/input/cypress,tm2-touchkey.txt
@@ -1,13 +1,19 @@
 Samsung tm2-touchkey
 
 Required properties:
-- compatible: must be "cypress,tm2-touchkey"
+- compatible:
+    * "cypress,tm2-touchkey" - for the touchkey found on the tm2 board
+    * "cypress,midas-touchkey" - for the touchkey found on midas boards
+    * "cypress,aries-touchkey" - for the touchkey found on aries boards
 - reg: I2C address of the chip.
 - interrupts: interrupt to which the chip is connected (see interrupt
 	binding[0]).
 - vcc-supply : internal regulator output. 1.8V
 - vdd-supply : power supply for IC 3.3V
 
+Optional properties:
+- linux,keycodes: array of keycodes (max 4), default KEY_PHONE and KEY_BACK
+
 [0]: Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
 
 Example:
@@ -21,5 +27,6 @@ Example:
 			interrupts = <2 IRQ_TYPE_EDGE_FALLING>;
 			vcc-supply=<&ldo32_reg>;
 			vdd-supply=<&ldo33_reg>;
+			linux,keycodes = <KEY_PHONE KEY_BACK>;
 		};
 	};
diff --git a/Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt b/Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt
new file mode 100644
index 000000000000..b2a76301e632
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/ilitek,ili2xxx.txt
@@ -0,0 +1,25 @@
+Ilitek ILI210x/ILI251x touchscreen controller
+
+Required properties:
+- compatible:
+    ilitek,ili210x for ILI210x
+    ilitek,ili251x for ILI251x
+
+- reg: The I2C address of the device
+
+- interrupts: The sink for the touchscreen's IRQ output
+    See ../interrupt-controller/interrupts.txt
+
+Optional properties for main touchpad device:
+
+- reset-gpios: GPIO specifier for the touchscreen's reset pin (active low)
+
+Example:
+
+	touchscreen@41 {
+		compatible = "ilitek,ili251x";
+		reg = <0x41>;
+		interrupt-parent = <&gpio4>;
+		interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio5 21 GPIO_ACTIVE_LOW>;
+	};
diff --git a/Documentation/devicetree/bindings/input/msm-vibrator.txt b/Documentation/devicetree/bindings/input/msm-vibrator.txt
new file mode 100644
index 000000000000..8dcf014ef2e5
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/msm-vibrator.txt
@@ -0,0 +1,36 @@
+* Device tree bindings for the Qualcomm MSM vibrator
+
+Required properties:
+
+  - compatible: Should be one of
+		"qcom,msm8226-vibrator"
+		"qcom,msm8974-vibrator"
+  - reg: the base address and length of the IO memory for the registers.
+  - pinctrl-names: set to default.
+  - pinctrl-0: phandles pointing to pin configuration nodes. See
+               Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+  - clock-names: set to pwm
+  - clocks: phandle of the clock. See
+            Documentation/devicetree/bindings/clock/clock-bindings.txt
+  - enable-gpios: GPIO that enables the vibrator.
+
+Optional properties:
+
+  - vcc-supply: phandle to the regulator that provides power to the sensor.
+
+Example from a LG Nexus 5 (hammerhead) phone:
+
+vibrator@fd8c3450 {
+	reg = <0xfd8c3450 0x400>;
+	compatible = "qcom,msm8974-vibrator";
+
+	vcc-supply = <&pm8941_l19>;
+
+	clocks = <&mmcc CAMSS_GP1_CLK>;
+	clock-names = "pwm";
+
+	enable-gpios = <&msmgpio 60 GPIO_ACTIVE_HIGH>;
+
+	pinctrl-names = "default";
+	pinctrl-0 = <&vibrator_pin>;
+};
diff --git a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
index da2dc5d6c98b..870b8c5cce9b 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/edt-ft5x06.txt
@@ -1,11 +1,12 @@
 FocalTech EDT-FT5x06 Polytouch driver
 =====================================
 
-There are 3 variants of the chip for various touch panel sizes
+There are 5 variants of the chip for various touch panel sizes
 FT5206GE1  2.8" .. 3.8"
 FT5306DE4  4.3" .. 7"
 FT5406EE8  7"   .. 8.9"
 FT5506EEG  7"   .. 8.9"
+FT5726NEI  5.7” .. 11.6"
 
 The software interface is identical for all those chips, so that
 currently there is no need for the driver to distinguish between the
@@ -19,6 +20,7 @@ Required properties:
            or:  "edt,edt-ft5306"
            or:  "edt,edt-ft5406"
            or:  "edt,edt-ft5506"
+           or:  "evervision,ev-ft5726"
            or:  "focaltech,ft6236"
 
  - reg:         I2C slave address of the chip (0x38)
@@ -42,6 +44,15 @@ Optional properties:
 
  - offset:      allows setting the edge compensation in the range from
                 0 to 31.
+
+ - offset-x:    Same as offset, but applies only to the horizontal position.
+                Range from 0 to 80, only supported by evervision,ev-ft5726
+                devices.
+
+ - offset-y:    Same as offset, but applies only to the vertical position.
+                Range from 0 to 80, only supported by evervision,ev-ft5726
+                devices.
+
  - touchscreen-size-x	   : See touchscreen.txt
  - touchscreen-size-y	   : See touchscreen.txt
  - touchscreen-fuzz-x      : See touchscreen.txt
diff --git a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
index f7e95c52f3c7..8cf0b4d38a7e 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt
@@ -3,6 +3,7 @@ Device tree bindings for Goodix GT9xx series touchscreen controller
 Required properties:
 
  - compatible		: Should be "goodix,gt1151"
+				 or "goodix,gt5688"
 				 or "goodix,gt911"
 				 or "goodix,gt9110"
 				 or "goodix,gt912"
@@ -18,11 +19,14 @@ Optional properties:
  - irq-gpios		: GPIO pin used for IRQ. The driver uses the
 			  interrupt gpio pin as output to reset the device.
  - reset-gpios		: GPIO pin used for reset
-
- - touchscreen-inverted-x  : X axis is inverted (boolean)
- - touchscreen-inverted-y  : Y axis is inverted (boolean)
- - touchscreen-swapped-x-y : X and Y axis are swapped (boolean)
-                             (swapping is done after inverting the axis)
+ - touchscreen-inverted-x
+ - touchscreen-inverted-y
+ - touchscreen-size-x
+ - touchscreen-size-y
+ - touchscreen-swapped-x-y
+
+The touchscreen-* properties are documented in touchscreen.txt in this
+directory.
 
 Example:
 
diff --git a/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt
index 64ad48b824a2..019373253b28 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/sitronix-st1232.txt
@@ -1,13 +1,17 @@
-* Sitronix st1232 touchscreen controller
+* Sitronix st1232 or st1633 touchscreen controller
 
 Required properties:
-- compatible: must be "sitronix,st1232"
+- compatible: must contain one of
+  * "sitronix,st1232"
+  * "sitronix,st1633"
 - reg: I2C address of the chip
 - interrupts: interrupt to which the chip is connected
 
 Optional properties:
 - gpios: a phandle to the reset GPIO
 
+For additional optional properties see: touchscreen.txt
+
 Example:
 
 	i2c@00000000 {
diff --git a/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt
index 4886c4aa2906..0ebe6dd043c7 100644
--- a/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt
+++ b/Documentation/devicetree/bindings/input/touchscreen/sx8654.txt
@@ -1,10 +1,17 @@
 * Semtech SX8654 I2C Touchscreen Controller
 
 Required properties:
-- compatible: must be "semtech,sx8654"
+- compatible: must be one of the following, depending on the model:
+	"semtech,sx8650"
+	"semtech,sx8654"
+	"semtech,sx8655"
+	"semtech,sx8656"
 - reg: i2c slave address
 - interrupts: touch controller interrupt
 
+Optional properties:
+ - reset-gpios: GPIO specification for the NRST input
+
 Example:
 
 	sx8654@48 {
@@ -12,4 +19,5 @@ Example:
 		reg = <0x48>;
 		interrupt-parent = <&gpio6>;
 		interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio4 2 GPIO_ACTIVE_LOW>;
 	};