Merge tag 'hwmon-for-linus-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon updates from Guenter Roeck:
 "Explicit support for ina231 added to ina2xx driver.

  Minor improvements, cleanup and fixes in various drivers"

* tag 'hwmon-for-linus-v3.20' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (tmp102) add hibernation callbacks
  hwmon: (ads2828) Only keep data in device data structure if needed
  hwmon: (ads2828) Convert to use regmap
  hwmon: (jc42) Allow negative hysteresis temperatures
  hwmon: (adc128d818) Do proper sign extension
  hwmon: (ad7314) Do proper sign extension
  hwmon: (abx500) Fix format string warnings
  hwmon: (jc42) Fix integer overflow when writing hysteresis value
  hwmon: (jc42) Fix integer overflow
  hwmon: (jc42) Use sign_extend32 for sign extension
  hwmon: (ina2xx) Add ina231 compatible string
  hwmon: (ina2xx) use DIV_ROUND_CLOSEST() to avoid rounding errors
  hwmon: (ina2xx) remove an unnecessary dev_get_drvdata() result check
  hwmon: (ina2xx) implement update_interval attribute for ina226
  hwmon: (ina2xx) make shunt resistance configurable at run-time
  hwmon: (ina2xx) don't accept shunt values greater than the calibration factor
  hwmon: (ina2xx) remove a stray new line
  hwmon: (ina2xx) reinitialize the chip in case it's been reset
  hwmon: (nct7802) Constify struct regmap_config

1 files changed, 19 insertions, 4 deletions

diff --git a/Documentation/hwmon/ina2xx b/Documentation/hwmon/ina2xx
index 4223c2d3b508..cfd31d94c872 100644
--- a/Documentation/hwmon/ina2xx
+++ b/Documentation/hwmon/ina2xx
@@ -26,6 +26,12 @@ Supported chips:
     Datasheet: Publicly available at the Texas Instruments website
                http://www.ti.com/
 
+  * Texas Instruments INA231
+    Prefix: 'ina231'
+    Addresses: I2C 0x40 - 0x4f
+    Datasheet: Publicly available at the Texas Instruments website
+               http://www.ti.com/
+
 Author: Lothar Felten <l-felten@ti.com>
 
 Description
@@ -41,9 +47,18 @@ interface. The INA220 monitors both shunt drop and supply voltage.
 The INA226 is a current shunt and power monitor with an I2C interface.
 The INA226 monitors both a shunt voltage drop and bus supply voltage.
 
-The INA230 is a high or low side current shunt and power monitor with an I2C
-interface. The INA230 monitors both a shunt voltage drop and bus supply voltage.
+INA230 and INA231 are high or low side current shunt and power monitors
+with an I2C interface. The chips monitor both a shunt voltage drop and
+bus supply voltage.
 
-The shunt value in micro-ohms can be set via platform data or device tree.
-Please refer to the Documentation/devicetree/bindings/i2c/ina2xx.txt for bindings
+The shunt value in micro-ohms can be set via platform data or device tree at
+compile-time or via the shunt_resistor attribute in sysfs at run-time. Please
+refer to the Documentation/devicetree/bindings/i2c/ina2xx.txt for bindings
 if the device tree is used.
+
+Additionally ina226 supports update_interval attribute as described in
+Documentation/hwmon/sysfs-interface. Internally the interval is the sum of
+bus and shunt voltage conversion times multiplied by the averaging rate. We
+don't touch the conversion times and only modify the number of averages. The
+lower limit of the update_interval is 2 ms, the upper limit is 2253 ms.
+The actual programmed interval may vary from the desired value.