Merge branch 'i2c/for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux

Pull i2c updates from Wolfram Sang:

 - the first series of making i2c_device_id optional instead of
   mandatory (in favor of alternatives like of_device_id).

   This involves adding a new probe callback (probe_new) which removes
   some peculiarities I2C had for a long time now. The new probe is
   matching the other subsystems now and the old one will be removed
   once all users are converted. It is expected to take a while but
   there is ongoing interest in that.

 - SMBus Host Notify introduced 4.9 got refactored. They are now using
   interrupts instead of the alert callback which solves multiple
   issues.

 - new drivers for iMX LowPower I2C, Mellanox CPLD and its I2C mux

 - significant refactoring for bcm2835 driver

 - the usual set of driver updates and improvements

* 'i2c/for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (46 commits)
  i2c: fsl-lpi2c: read lpi2c fifo size in probe()
  i2c: octeon: thunderx: Remove double-check after interrupt
  i2c: octeon: thunderx: TWSI software reset in recovery
  i2c: cadence: Allow Cadence I2C to be selected for Cadence Xtensa CPUs
  i2c: sh_mobile: Add per-Generation fallback bindings
  i2c: rcar: Add per-Generation fallback bindings
  i2c: imx-lpi2c: add low power i2c bus driver
  dt-bindings: i2c: imx-lpi2c: add devicetree bindings
  i2c: designware-pcidrv: Add 10bit address feature to medfield/merrifield
  i2c: pxa: Add support for the I2C units found in Armada 3700
  i2c: pxa: Add definition of fast and high speed modes via the regs layout
  dt-bindings: i2c: pxa: Update the documentation for the Armada 3700
  i2c: qup: support SMBus block read
  i2c: qup: add ACPI support
  i2c: designware: Consolidate default functionality bits
  i2c: i2c-mux-gpio: update mux with gpiod_set_array_value_cansleep
  i2c: mux: pca954x: Add ACPI support for pca954x
  i2c: use an IRQ to report Host Notify events, not alert
  i2c: i801: remove SMBNTFDDAT reads as they always seem to return 0
  i2c: i801: use the BIT() macro for FEATURES_* also
  ...

2 files changed, 55 insertions, 4 deletions

diff --git a/Documentation/i2c/busses/i2c-mlxcpld b/Documentation/i2c/busses/i2c-mlxcpld
new file mode 100644
index 000000000000..4e46c440b38d
--- /dev/null
+++ b/Documentation/i2c/busses/i2c-mlxcpld
@@ -0,0 +1,47 @@
+Driver i2c-mlxcpld
+
+Author: Michael Shych <michaelsh@mellanox.com>
+
+This is the Mellanox I2C controller logic, implemented in Lattice CPLD
+device.
+Device supports:
+ - Master mode.
+ - One physical bus.
+ - Polling mode.
+
+This controller is equipped within the next Mellanox systems:
+"msx6710", "msx6720", "msb7700", "msn2700", "msx1410", "msn2410", "msb7800",
+"msn2740", "msn2100".
+
+The next transaction types are supported:
+ - Receive Byte/Block.
+ - Send Byte/Block.
+ - Read Byte/Block.
+ - Write Byte/Block.
+
+Registers:
+CTRL		0x1 - control reg.
+			Resets all the registers.
+HALF_CYC	0x4 - cycle reg.
+			Configure the width of I2C SCL half clock cycle (in 4 LPC_CLK
+			units).
+I2C_HOLD	0x5 - hold reg.
+			OE (output enable) is delayed by value set to this register
+			(in LPC_CLK units)
+CMD			0x6 - command reg.
+			Bit 0, 0 = write, 1 = read.
+			Bits [7:1] - the 7bit Address of the I2C device.
+			It should be written last as it triggers an I2C transaction.
+NUM_DATA	0x7 - data size reg.
+			Number of data bytes to write in read transaction
+NUM_ADDR	0x8 - address reg.
+			Number of address bytes to write in read transaction.
+STATUS		0x9 - status reg.
+			Bit 0 - transaction is completed.
+			Bit 4 - ACK/NACK.
+DATAx		0xa - 0x54  - 68 bytes data buffer regs.
+			For write transaction address is specified in four first bytes
+			(DATA1 - DATA4), data starting from DATA4.
+			For read transactions address is sent in a separate transaction and
+			specified in the four first bytes (DATA0 - DATA3). Data is read
+			starting from DATA0.
diff --git a/Documentation/i2c/smbus-protocol b/Documentation/i2c/smbus-protocol
index 14d4ec1be245..092d474f5843 100644
--- a/Documentation/i2c/smbus-protocol
+++ b/Documentation/i2c/smbus-protocol
@@ -200,10 +200,14 @@ alerting device's address.
 [S] [HostAddr] [Wr] A [DevAddr] A [DataLow] A [DataHigh] A [P]
 
 This is implemented in the following way in the Linux kernel:
-* I2C bus drivers which support SMBus Host Notify should call
-  i2c_setup_smbus_host_notify() to setup SMBus Host Notify support.
-* I2C drivers for devices which can trigger SMBus Host Notify should implement
-  the optional alert() callback.
+* I2C bus drivers which support SMBus Host Notify should report
+  I2C_FUNC_SMBUS_HOST_NOTIFY.
+* I2C bus drivers trigger SMBus Host Notify by a call to
+  i2c_handle_smbus_host_notify().
+* I2C drivers for devices which can trigger SMBus Host Notify will have
+  client->irq assigned to a Host Notify IRQ if noone else specified an other.
+
+There is currently no way to retrieve the data parameter from the client.
 
 
 Packet Error Checking (PEC)