Merge tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Device tree related changes for omaps.

Note that this branch is based on omap-cleanup-sparseirq-for-v3.7
to avoid merge conflicts with the sparseirq changes for gpio-twl4030
driver.

* tag 'omap-devel-dt-merged-for-v3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  arm/dts: Mux uart pins for omap4-sdp
  ARM: OMAP2+: select PINCTRL in Kconfig
  arm/dts: Add pinctrl driver entries for omap2/3/4
  arm/dts: Add omap36xx.dtsi file and rename omap3-beagle to omap3-beagle-xm
  ARM: dts: omap3-overo: Add support for the blue LED
  Documentation: dt: Update the OMAP documentation with Overo/Toby
  ARM: dts: OMAP3: Add support for Gumstix Overo with Tobi expansion board
  ARM: dts: OMAP4: Add reg and interrupts for every nodes
  ARM: dts: AM33XX: Specify reg and interrupt property for all nodes
  ARM: dts: AM33XX: Convert all hex numbers to lower-case
  ARM: dts: omap3-beagle: Enable audio support
  ARM: dts: omap5: Add McPDM and DMIC section to the dtsi file
  ARM: dts: omap5: Add McBSP entries
  ARM: dts: omap4: Add reg-names for McPDM and DMIC
  ARM: dts: omap4: Add McBSP entries
  ARM: dts: omap3: Add McBSP entries
  ARM: dts: omap2420-h4: Include omap2420.dtsi file instead the common omap2
  ARM: dts: omap2: Add McBSP entries for OMAP2420 and OMAP2430 SoC
  ARM: dts: omap3-beagle: Add heartbeat and mmc LEDs support
  ARM: dts: omap3: Add gpio-twl4030 properties for BeagleBoard and omap3-EVM
  ...

8 files changed, 235 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index ccdd0e53451f..d0051a750587 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -36,6 +36,9 @@ Boards:
 - OMAP3 BeagleBoard : Low cost community board
   compatible = "ti,omap3-beagle", "ti,omap3"
 
+- OMAP3 Tobi with Overo : Commercial expansion board with daughter board
+  compatible = "ti,omap3-tobi", "ti,omap3-overo", "ti,omap3"
+
 - OMAP4 SDP : Software Developement Board
   compatible = "ti,omap4-sdp", "ti,omap4430"
 
diff --git a/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt
index 16695d9cf1e8..66788fda1db3 100644
--- a/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt
+++ b/Documentation/devicetree/bindings/gpio/gpio-twl4030.txt
@@ -11,6 +11,11 @@ Required properties:
 - interrupt-controller: Mark the device node as an interrupt controller
   The first cell is the GPIO number.
   The second cell is not used.
+- ti,use-leds : Enables LEDA and LEDB outputs if set
+- ti,debounce : if n-th bit is set, debounces GPIO-n
+- ti,mmc-cd : if n-th bit is set, GPIO-n controls VMMC(n+1)
+- ti,pullups : if n-th bit is set, set a pullup on GPIO-n
+- ti,pulldowns : if n-th bit is set, set a pulldown on GPIO-n
 
 Example:
 
@@ -20,4 +25,5 @@ twl_gpio: gpio {
     gpio-controller;
     #interrupt-cells = <2>;
     interrupt-controller;
+    ti,use-leds;
 };
diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
index 1a85f986961b..2f5322b119eb 100644
--- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt
+++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt
@@ -56,3 +56,4 @@ stm,m41t00		Serial Access TIMEKEEPER
 stm,m41t62		Serial real-time clock (RTC) with alarm
 stm,m41t80		M41T80 - SERIAL ACCESS RTC WITH ALARMS
 ti,tsc2003		I2C Touch-Screen Controller
+ti,tmp102		Low Power Digital Temperature Sensor with SMBUS/Two Wire Serial Interface
diff --git a/Documentation/devicetree/bindings/lpddr2/lpddr2-timings.txt b/Documentation/devicetree/bindings/lpddr2/lpddr2-timings.txt
new file mode 100644
index 000000000000..9ceb19e0c7fd
--- /dev/null
+++ b/Documentation/devicetree/bindings/lpddr2/lpddr2-timings.txt
@@ -0,0 +1,52 @@
+* AC timing parameters of LPDDR2(JESD209-2) memories for a given speed-bin
+
+Required properties:
+- compatible : Should be "jedec,lpddr2-timings"
+- min-freq : minimum DDR clock frequency for the speed-bin. Type is <u32>
+- max-freq : maximum DDR clock frequency for the speed-bin. Type is <u32>
+
+Optional properties:
+
+The following properties represent AC timing parameters from the memory
+data-sheet of the device for a given speed-bin. All these properties are
+of type <u32> and the default unit is ps (pico seconds). Parameters with
+a different unit have a suffix indicating the unit such as 'tRAS-max-ns'
+- tRCD
+- tWR
+- tRAS-min
+- tRRD
+- tWTR
+- tXP
+- tRTP
+- tDQSCK-max
+- tFAW
+- tZQCS
+- tZQinit
+- tRPab
+- tZQCL
+- tCKESR
+- tRAS-max-ns
+- tDQSCK-max-derated
+
+Example:
+
+timings_elpida_ECB240ABACN_400mhz: lpddr2-timings@0 {
+	compatible	= "jedec,lpddr2-timings";
+	min-freq	= <10000000>;
+	max-freq	= <400000000>;
+	tRPab		= <21000>;
+	tRCD		= <18000>;
+	tWR		= <15000>;
+	tRAS-min	= <42000>;
+	tRRD		= <10000>;
+	tWTR		= <7500>;
+	tXP		= <7500>;
+	tRTP		= <7500>;
+	tCKESR		= <15000>;
+	tDQSCK-max	= <5500>;
+	tFAW		= <50000>;
+	tZQCS		= <90000>;
+	tZQCL		= <360000>;
+	tZQinit		= <1000000>;
+	tRAS-max-ns	= <70000>;
+};
diff --git a/Documentation/devicetree/bindings/lpddr2/lpddr2.txt b/Documentation/devicetree/bindings/lpddr2/lpddr2.txt
new file mode 100644
index 000000000000..58354a075e13
--- /dev/null
+++ b/Documentation/devicetree/bindings/lpddr2/lpddr2.txt
@@ -0,0 +1,102 @@
+* LPDDR2 SDRAM memories compliant to JEDEC JESD209-2
+
+Required properties:
+- compatible : Should be one of - "jedec,lpddr2-nvm", "jedec,lpddr2-s2",
+  "jedec,lpddr2-s4"
+
+  "ti,jedec-lpddr2-s2" should be listed if the memory part is LPDDR2-S2 type
+
+  "ti,jedec-lpddr2-s4" should be listed if the memory part is LPDDR2-S4 type
+
+  "ti,jedec-lpddr2-nvm" should be listed if the memory part is LPDDR2-NVM type
+
+- density  : <u32> representing density in Mb (Mega bits)
+
+- io-width : <u32> representing bus width. Possible values are 8, 16, and 32
+
+Optional properties:
+
+The following optional properties represent the minimum value of some AC
+timing parameters of the DDR device in terms of number of clock cycles.
+These values shall be obtained from the device data-sheet.
+- tRRD-min-tck
+- tWTR-min-tck
+- tXP-min-tck
+- tRTP-min-tck
+- tCKE-min-tck
+- tRPab-min-tck
+- tRCD-min-tck
+- tWR-min-tck
+- tRASmin-min-tck
+- tCKESR-min-tck
+- tFAW-min-tck
+
+Child nodes:
+- The lpddr2 node may have one or more child nodes of type "lpddr2-timings".
+  "lpddr2-timings" provides AC timing parameters of the device for
+  a given speed-bin. The user may provide the timings for as many
+  speed-bins as is required. Please see Documentation/devicetree/
+  bindings/lpddr2/lpddr2-timings.txt for more information on "lpddr2-timings"
+
+Example:
+
+elpida_ECB240ABACN : lpddr2 {
+	compatible	= "Elpida,ECB240ABACN","jedec,lpddr2-s4";
+	density		= <2048>;
+	io-width	= <32>;
+
+	tRPab-min-tck	= <3>;
+	tRCD-min-tck	= <3>;
+	tWR-min-tck	= <3>;
+	tRASmin-min-tck	= <3>;
+	tRRD-min-tck	= <2>;
+	tWTR-min-tck	= <2>;
+	tXP-min-tck	= <2>;
+	tRTP-min-tck	= <2>;
+	tCKE-min-tck	= <3>;
+	tCKESR-min-tck	= <3>;
+	tFAW-min-tck	= <8>;
+
+	timings_elpida_ECB240ABACN_400mhz: lpddr2-timings@0 {
+		compatible	= "jedec,lpddr2-timings";
+		min-freq	= <10000000>;
+		max-freq	= <400000000>;
+		tRPab		= <21000>;
+		tRCD		= <18000>;
+		tWR		= <15000>;
+		tRAS-min	= <42000>;
+		tRRD		= <10000>;
+		tWTR		= <7500>;
+		tXP		= <7500>;
+		tRTP		= <7500>;
+		tCKESR		= <15000>;
+		tDQSCK-max	= <5500>;
+		tFAW		= <50000>;
+		tZQCS		= <90000>;
+		tZQCL		= <360000>;
+		tZQinit		= <1000000>;
+		tRAS-max-ns	= <70000>;
+	};
+
+	timings_elpida_ECB240ABACN_200mhz: lpddr2-timings@1 {
+		compatible	= "jedec,lpddr2-timings";
+		min-freq	= <10000000>;
+		max-freq	= <200000000>;
+		tRPab		= <21000>;
+		tRCD		= <18000>;
+		tWR		= <15000>;
+		tRAS-min	= <42000>;
+		tRRD		= <10000>;
+		tWTR		= <10000>;
+		tXP		= <7500>;
+		tRTP		= <7500>;
+		tCKESR		= <15000>;
+		tDQSCK-max	= <5500>;
+		tFAW		= <50000>;
+		tZQCS		= <90000>;
+		tZQCL		= <360000>;
+		tZQinit		= <1000000>;
+		tRAS-max-ns	= <70000>;
+	};
+
+}
diff --git a/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt
new file mode 100644
index 000000000000..938f8e1ba205
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/ti/emif.txt
@@ -0,0 +1,55 @@
+* EMIF family of TI SDRAM controllers
+
+EMIF - External Memory Interface - is an SDRAM controller used in
+TI SoCs. EMIF supports, based on the IP revision, one or more of
+DDR2/DDR3/LPDDR2 protocols. This binding describes a given instance
+of the EMIF IP and memory parts attached to it.
+
+Required properties:
+- compatible	: Should be of the form "ti,emif-<ip-rev>" where <ip-rev>
+  is the IP revision of the specific EMIF instance.
+
+- phy-type	: <u32> indicating the DDR phy type. Following are the
+  allowed values
+  <1>	: Attila PHY
+  <2>	: Intelli PHY
+
+- device-handle	: phandle to a "lpddr2" node representing the memory part
+
+- ti,hwmods	: For TI hwmods processing and omap device creation
+  the value shall be "emif<n>" where <n> is the number of the EMIF
+  instance with base 1.
+
+Optional properties:
+- cs1-used		: Have this property if CS1 of this EMIF
+  instance has a memory part attached to it. If there is a memory
+  part attached to CS1, it should be the same type as the one on CS0,
+  so there is no need to give the details of this memory part.
+
+- cal-resistor-per-cs	: Have this property if the board has one
+  calibration resistor per chip-select.
+
+- hw-caps-read-idle-ctrl: Have this property if the controller
+  supports read idle window programming
+
+- hw-caps-dll-calib-ctrl: Have this property if the controller
+  supports dll calibration control
+
+- hw-caps-ll-interface	: Have this property if the controller
+  has a low latency interface and corresponding interrupt events
+
+- hw-caps-temp-alert	: Have this property if the controller
+  has capability for generating SDRAM temperature alerts
+
+Example:
+
+emif1: emif@0x4c000000 {
+	compatible	= "ti,emif-4d";
+	ti,hwmods	= "emif2";
+	phy-type	= <1>;
+	device-handle	= <&elpida_ECB240ABACN>;
+	cs1-used;
+	hw-caps-read-idle-ctrl;
+	hw-caps-ll-interface;
+	hw-caps-temp-alert;
+};
diff --git a/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt b/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt
new file mode 100644
index 000000000000..0d439dfc1aa5
--- /dev/null
+++ b/Documentation/devicetree/bindings/tty/serial/nxp-lpc32xx-hsuart.txt
@@ -0,0 +1,14 @@
+* NXP LPC32xx SoC High Speed UART
+
+Required properties:
+- compatible: Should be "nxp,lpc3220-hsuart"
+- reg: Should contain registers location and length
+- interrupts: Should contain interrupt
+
+Example:
+
+	uart1: serial@40014000 {
+		compatible = "nxp,lpc3220-hsuart";
+		reg = <0x40014000 0x1000>;
+		interrupts = <26 0>;
+	};
diff --git a/Documentation/devicetree/bindings/tty/serial/of-serial.txt b/Documentation/devicetree/bindings/tty/serial/of-serial.txt
index 0847fdeee11a..ba385f2e0ddc 100644
--- a/Documentation/devicetree/bindings/tty/serial/of-serial.txt
+++ b/Documentation/devicetree/bindings/tty/serial/of-serial.txt
@@ -25,6 +25,8 @@ Optional properties:
   accesses to the UART (e.g. TI davinci).
 - used-by-rtas : set to indicate that the port is in use by the OpenFirmware
   RTAS and should not be registered.
+- no-loopback-test: set to indicate that the port does not implements loopback
+  test mode
 
 Example: