Merge tag 'pinctrl-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl

Pull pincontrol updates from Linus Walleij:
 "This is the bulk of pin control changes for the v4.1 development
  cycle.  Nothing really exciting this time: we basically added a few
  new drivers and subdrivers and stabilized them in linux-next.  Some
  cleanups too.  With sunrisepoint Intel has a real fine fully featured
  pin control driver for contemporary hardware, and the AMD driver is
  also for large deployments.  Most of the others are ARM devices.

  New drivers:
    - Intel Sunrisepoint
    - AMD KERNCZ GPIO
    - Broadcom Cygnus IOMUX

  New subdrivers:
    - Marvell MVEBU Armada 39x SoCs
    - Samsung Exynos 5433
    - nVidia Tegra 210
    - Mediatek MT8135
    - Mediatek MT8173
    - AMLogic Meson8b
    - Qualcomm PM8916

  On top of this cleanups and development history for the above drivers
  as issues were fixed after merging"

* tag 'pinctrl-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (71 commits)
  pinctrl: sirf: move sgpio lock into state container
  pinctrl: Add support for PM8916 GPIO's and MPP's
  pinctrl: bcm2835: Fix support for threaded level triggered IRQs
  sh-pfc: r8a7790: add EtherAVB pin groups
  pinctrl: Document "function" + "pins" pinmux binding
  pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support
  pinctrl: fsl: imx: Check for 0 config register
  pinctrl: Add support for Meson8b
  documentation: Extend pinctrl docs for Meson8b
  pinctrl: Cleanup Meson8 driver
  Fix inconsistent spinlock of AMD GPIO driver which can be recognized by static analysis tool smatch. Declare constant Variables with Sparse's suggestion.
  pinctrl: at91: convert __raw to endian agnostic IO
  pinctrl: constify of_device_id array
  pinctrl: pinconf-generic: add dt node names to error messages
  pinctrl: pinconf-generic: scan also referenced phandle node
  pinctrl: mvebu: add suspend/resume support to Armada XP pinctrl driver
  pinctrl: st: Display pin's function when printing pinctrl debug information
  pinctrl: st: Show correct pin direction also in GPIO mode
  pinctrl: st: Supply a GPIO get_direction() call-back
  pinctrl: st: Move st_get_pio_control() further up the source file
  ...

9 files changed, 652 insertions, 12 deletions

diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt
new file mode 100644
index 000000000000..6540ca56be5e
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-gpio.txt
@@ -0,0 +1,98 @@
+Broadcom Cygnus GPIO/PINCONF Controller
+
+Required properties:
+
+- compatible:
+    Must be "brcm,cygnus-ccm-gpio", "brcm,cygnus-asiu-gpio", or
+    "brcm,cygnus-crmu-gpio"
+
+- reg:
+    Define the base and range of the I/O address space that contains the Cygnus
+GPIO/PINCONF controller registers
+
+- #gpio-cells:
+    Must be two. The first cell is the GPIO pin number (within the
+controller's pin space) and the second cell is used for the following:
+    bit[0]: polarity (0 for active high and 1 for active low)
+
+- gpio-controller:
+    Specifies that the node is a GPIO controller
+
+Optional properties:
+
+- interrupts:
+    Interrupt ID
+
+- interrupt-controller:
+    Specifies that the node is an interrupt controller
+
+- pinmux:
+    Specifies the phandle to the IOMUX device, where pins can be individually
+muxed to GPIO
+
+Supported generic PINCONF properties in child nodes:
+
+- pins:
+    The list of pins (within the controller's own pin space) that properties
+in the node apply to. Pin names are "gpio-<pin>"
+
+- bias-disable:
+    Disable pin bias
+
+- bias-pull-up:
+    Enable internal pull up resistor
+
+- bias-pull-down:
+    Enable internal pull down resistor
+
+- drive-strength:
+    Valid drive strength values include 2, 4, 6, 8, 10, 12, 14, 16 (mA)
+
+Example:
+	gpio_ccm: gpio@1800a000 {
+		compatible = "brcm,cygnus-ccm-gpio";
+		reg = <0x1800a000 0x50>,
+		      <0x0301d164 0x20>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+
+		touch_pins: touch_pins {
+			pwr: pwr {
+				pins = "gpio-0";
+				drive-strength = <16>;
+			};
+
+			event: event {
+				pins = "gpio-1";
+				bias-pull-up;
+			};
+		};
+	};
+
+	gpio_asiu: gpio@180a5000 {
+		compatible = "brcm,cygnus-asiu-gpio";
+		reg = <0x180a5000 0x668>;
+		#gpio-cells = <2>;
+		gpio-controller;
+		interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+	};
+
+	/*
+	 * Touchscreen that uses the CCM GPIO 0 and 1
+	 */
+	tsc {
+		...
+		...
+		gpio-pwr = <&gpio_ccm 0 0>;
+		gpio-event = <&gpio_ccm 1 0>;
+	};
+
+	/* Bluetooth that uses the ASIU GPIO 5, with polarity inverted */
+	bluetooth {
+		...
+		...
+		bcm,rfkill-bank-sel = <&gpio_asiu 5 1>
+	}
diff --git a/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-pinmux.txt
new file mode 100644
index 000000000000..3600d5c6c4d7
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/brcm,cygnus-pinmux.txt
@@ -0,0 +1,132 @@
+Broadcom Cygnus IOMUX Controller
+
+The Cygnus IOMUX controller supports group based mux configuration. In
+addition, certain pins can be muxed to GPIO function individually.
+
+Required properties:
+
+- compatible:
+    Must be "brcm,cygnus-pinmux"
+
+- reg:
+    Define the base and range of the I/O address space that contains the Cygnus
+IOMUX registers
+
+Properties in subnodes:
+
+- function:
+    The mux function to select
+
+- groups:
+    The list of groups to select with a given function
+
+For more details, refer to
+Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+
+For example:
+
+	pinmux: pinmux@0x0301d0c8 {
+		compatible = "brcm,cygnus-pinmux";
+		reg = <0x0301d0c8 0x1b0>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&i2s0_default>;
+
+		i2s0_default: i2s0_default {
+			mux {
+				function = "i2s0";
+				groups = "i2s0_0_grp", "i2s0_1_grp";
+			};
+		};
+	};
+
+List of supported functions and groups in Cygnus:
+
+"i2s0": "i2s0_0_grp", "i2s0_1_grp"
+
+"i2s1": "i2s1_0_grp", "i2s1_1_grp"
+
+"i2s2": "i2s2_0_grp", "i2s2_1_grp", "i2s2_2_grp", "i2s2_3_grp", "i2s2_4_grp"
+
+"spdif": "spdif_grp"
+
+"pwm0": "pwm0_grp"
+
+"pwm1": "pwm1_grp"
+
+"pwm2": "pwm2_grp"
+
+"pwm3": "pwm3_grp"
+
+"pwm4": "pwm4_grp"
+
+"pwm5": "pwm5_grp"
+
+"key": "key0_grp", "key1_grp", "key2_grp", "key3_grp", "key4_grp", "key5_grp",
+"key6_grp", "key7_grp", "key8_grp", "key9_grp", "key10_grp", "key11_grp",
+"key12_grp", "key13_grp", "key14_grp", "key15_grp"
+
+"audio_dte": "audio_dte0_grp", "audio_dte1_grp", "audio_dte2_grp", "audio_dte3_grp"
+
+"smart_card0": "smart_card0_grp", "smart_card0_fcb_grp"
+
+"smart_card1": "smart_card1_grp", "smart_card1_fcb_grp"
+
+"spi0": "spi0_grp"
+
+"spi1": "spi1_grp"
+
+"spi2": "spi2_grp"
+
+"spi3": "spi3_grp"
+
+"spi4": "spi4_0_grp", "spi4_1_grp"
+
+"spi5": "spi5_grp"
+
+"sw_led0": "sw_led0_0_grp", "sw_led0_1_grp"
+
+"sw_led1": "sw_led1_grp"
+
+"sw_led2": "sw_led2_0_grp", "sw_led2_1_grp"
+
+"d1w": "d1w_grp"
+
+"lcd": "lcd_grp"
+
+"sram": "sram_0_grp", "sram_1_grp"
+
+"uart0": "uart0_grp"
+
+"uart1": "uart1_grp", "uart1_dte_grp"
+
+"uart2": "uart2_grp"
+
+"uart3": "uart3_grp"
+
+"uart4": "uart4_grp"
+
+"qspi": "qspi_0_grp", "qspi_1_grp"
+
+"nand": "nand_grp"
+
+"sdio0": "sdio0_grp", "sdio0_cd_grp", "sdio0_mmc_grp"
+
+"sdio1": "sdio1_data_0_grp", "sdio1_data_1_grp", "sdio1_cd_grp",
+"sdio1_led_grp", "sdio1_mmc_grp"
+
+"can0": "can0_grp"
+
+"can1": "can1_grp"
+
+"cam": "cam_led_grp", "cam_0_grp", "cam_1_grp"
+
+"bsc1": "bsc1_grp"
+
+"pcie_clkreq": "pcie_clkreq_grp"
+
+"usb0_oc": "usb0_oc_grp"
+
+"usb1_oc": "usb1_oc_grp"
+
+"usb2_oc": "usb2_oc_grp"
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
new file mode 100644
index 000000000000..5b1a9dc004f4
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-39x-pinctrl.txt
@@ -0,0 +1,78 @@
+* Marvell Armada 39x SoC pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage.
+
+Required properties:
+- compatible: "marvell,88f6920-pinctrl", "marvell,88f6928-pinctrl"
+  depending on the specific variant of the SoC being used.
+- reg: register specifier of MPP registers
+
+Available mpp pins/groups and functions:
+Note: brackets (x) are not part of the mpp name for marvell,function and given
+only for more detailed description in this document.
+
+name    pins    functions
+================================================================================
+mpp0	0	gpio, ua0(rxd)
+mpp1	1	gpio, ua0(txd)
+mpp2	2	gpio, i2c0(sck)
+mpp3	3	gpio, i2c0(sda)
+mpp4	4	gpio, ua1(txd), ua0(rts), smi(mdc)
+mpp5	5	gpio, ua1(rxd), ua0(cts), smi(mdio)
+mpp6	6	gpio, dev(cs3), xsmi(mdio)
+mpp7	7	gpio, dev(ad9), xsmi(mdc)
+mpp8	8	gpio, dev(ad10), ptp(trig)
+mpp9	9	gpio, dev(ad11), ptp(clk)
+mpp10	10	gpio, dev(ad12), ptp(event)
+mpp11	11	gpio, dev(ad13), led(clk)
+mpp12	12	gpio, pcie0(rstout), dev(ad14), led(stb)
+mpp13	13	gpio, dev(ad15), led(data)
+mpp14	14	gpio, m(vtt), dev(wen1), ua1(txd)
+mpp15	15	gpio, pcie0(rstout), spi0(mosi), i2c1(sck)
+mpp16	16	gpio, m(decc), spi0(miso), i2c1(sda)
+mpp17	17	gpio, ua1(rxd), spi0(sck), smi(mdio)
+mpp18	18	gpio, ua1(txd), spi0(cs0), i2c2(sck)
+mpp19	19	gpio, sata1(present) [1], ua0(cts), ua1(rxd), i2c2(sda)
+mpp20	20	gpio, sata0(present) [1], ua0(rts), ua1(txd), smi(mdc)
+mpp21	21	gpio, spi0(cs1), sata0(present) [1], sd(cmd), dev(bootcs), ge(rxd0)
+mpp22	22	gpio, spi0(mosi), dev(ad0)
+mpp23	23	gpio, spi0(sck), dev(ad2)
+mpp24	24	gpio, spi0(miso), ua0(cts), ua1(rxd), sd(d4), dev(readyn)
+mpp25	25	gpio, spi0(cs0), ua0(rts), ua1(txd), sd(d5), dev(cs0)
+mpp26	26	gpio, spi0(cs2), i2c1(sck), sd(d6), dev(cs1)
+mpp27	27	gpio, spi0(cs3), i2c1(sda), sd(d7), dev(cs2), ge(txclkout)
+mpp28	28	gpio, sd(clk), dev(ad5), ge(txd0)
+mpp29	29	gpio, dev(ale0), ge(txd1)
+mpp30	30	gpio, dev(oen), ge(txd2)
+mpp31	31	gpio, dev(ale1), ge(txd3)
+mpp32	32	gpio, dev(wen0), ge(txctl)
+mpp33	33	gpio, m(decc), dev(ad3)
+mpp34	34	gpio, dev(ad1)
+mpp35	35	gpio, ref(clk), dev(a1)
+mpp36	36	gpio, dev(a0)
+mpp37	37	gpio, sd(d3), dev(ad8), ge(rxclk)
+mpp38	38	gpio, ref(clk), sd(d0), dev(ad4), ge(rxd1)
+mpp39	39	gpio, i2c1(sck), ua0(cts), sd(d1), dev(a2), ge(rxd2)
+mpp40	40	gpio, i2c1(sda), ua0(rts), sd(d2), dev(ad6), ge(rxd3)
+mpp41	41	gpio, ua1(rxd), ua0(cts), spi1(cs3), dev(burstn), nd(rbn0), ge(rxctl)
+mpp42	42	gpio, ua1(txd), ua0(rts), dev(ad7)
+mpp43	43	gpio, pcie0(clkreq), m(vtt), m(decc), spi1(cs2), dev(clkout), nd(rbn1)
+mpp44	44	gpio, sata0(present) [1], sata1(present) [1], led(clk)
+mpp45	45	gpio, ref(clk), pcie0(rstout), ua1(rxd)
+mpp46	46	gpio, ref(clk), pcie0(rstout), ua1(txd), led(stb)
+mpp47	47	gpio, sata0(present) [1], sata1(present) [1], led(data)
+mpp48	48	gpio, sata0(present) [1], m(vtt), tdm(pclk) [1], audio(mclk) [1], sd(d4), pcie0(clkreq), ua1(txd)
+mpp49	49	gpio, tdm(fsync) [1], audio(lrclk) [1], sd(d5), ua2(rxd)
+mpp50	50	gpio, pcie0(rstout), tdm(drx) [1], audio(extclk) [1], sd(cmd), ua2(rxd)
+mpp51	51	gpio, tdm(dtx) [1], audio(sdo) [1], m(decc), ua2(txd)
+mpp52	52	gpio, pcie0(rstout), tdm(intn) [1], audio(sdi) [1], sd(d6), i2c3(sck)
+mpp53	53	gpio, sata1(present) [1], sata0(present) [1], tdm(rstn) [1], audio(bclk) [1], sd(d7), i2c3(sda)
+mpp54	54	gpio, sata0(present) [1], sata1(present) [1], pcie0(rstout), sd(d3), ua3(txd)
+mpp55	55	gpio, ua1(cts), spi1(cs1), sd(d0), ua1(rxd), ua3(rxd)
+mpp56	56	gpio, ua1(rts), m(decc), spi1(mosi), ua1(txd)
+mpp57	57	gpio, spi1(sck), sd(clk), ua1(txd)
+mpp58	58	gpio, i2c1(sck), pcie2(clkreq), spi1(miso), sd(d1), ua1(rxd)
+mpp59	59	gpio, pcie0(rstout), i2c1(sda), spi1(cs0), sd(d2)
+
+[1]: only available on 88F6928
diff --git a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
index 17e7240c6998..3f6a524cc5ff 100644
--- a/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/meson,pinctrl.txt
@@ -1,7 +1,7 @@
 == Amlogic Meson pinmux controller ==
 
 Required properties for the root node:
- - compatible: "amlogic,meson8-pinctrl"
+ - compatible: "amlogic,meson8-pinctrl" or "amlogic,meson8b-pinctrl"
  - reg: address and size of registers controlling irq functionality
 
 === GPIO sub-nodes ===
diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt
new file mode 100644
index 000000000000..a62d82d5fbe9
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt
@@ -0,0 +1,166 @@
+NVIDIA Tegra210 pinmux controller
+
+Required properties:
+- compatible: "nvidia,tegra210-pinmux"
+- reg: Should contain a list of base address and size pairs for:
+  - first entry: The APB_MISC_GP_*_PADCTRL registers (pad control)
+  - second entry: The PINMUX_AUX_* registers (pinmux)
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices, including the meaning of the
+phrase "pin configuration node".
+
+Tegra's pin configuration nodes act as a container for an arbitrary number of
+subnodes. Each of these subnodes represents some desired configuration for a
+pin, a group, or a list of pins or groups. This configuration can include the
+mux function to select on those pin(s)/group(s), and various pin configuration
+parameters, such as pull-up, tristate, drive strength, etc.
+
+The name of each subnode is not important; all subnodes should be enumerated
+and processed purely based on their content.
+
+Each subnode only affects those parameters that are explicitly listed. In
+other words, a subnode that lists a mux function but no pin configuration
+parameters implies no information about any pin configuration parameters.
+Similarly, a pin subnode that describes a pullup parameter implies no
+information about e.g. the mux function or tristate parameter. For this
+reason, even seemingly boolean values are actually tristates in this binding:
+unspecified, off, or on. Unspecified is represented as an absent property,
+and off/on are represented as integer values 0 and 1.
+
+See the TRM to determine which properties and values apply to each pin/group.
+Macro values for property values are defined in
+include/dt-binding/pinctrl/pinctrl-tegra.h.
+
+Required subnode-properties:
+- nvidia,pins : An array of strings. Each string contains the name of a pin or
+    group. Valid values for these names are listed below.
+
+Optional subnode-properties:
+- nvidia,function: A string containing the name of the function to mux to the
+    pin or group.
+- nvidia,pull: Integer, representing the pull-down/up to apply to the pin.
+    0: none, 1: down, 2: up.
+- nvidia,tristate: Integer.
+    0: drive, 1: tristate.
+- nvidia,enable-input: Integer. Enable the pin's input path.
+    enable :TEGRA_PIN_ENABLE0 and
+    disable or output only: TEGRA_PIN_DISABLE.
+- nvidia,open-drain: Integer.
+    enable: TEGRA_PIN_ENABLE.
+    disable: TEGRA_PIN_DISABLE.
+- nvidia,lock: Integer. Lock the pin configuration against further changes
+    until reset.
+    enable: TEGRA_PIN_ENABLE.
+    disable: TEGRA_PIN_DISABLE.
+- nvidia,io-hv: Integer. Select high-voltage receivers.
+    normal: TEGRA_PIN_DISABLE
+    high: TEGRA_PIN_ENABLE
+- nvidia,high-speed-mode: Integer. Enable high speed mode the pins.
+    normal: TEGRA_PIN_DISABLE
+    high: TEGRA_PIN_ENABLE
+- nvidia,schmitt: Integer. Enables Schmitt Trigger on the input.
+    normal: TEGRA_PIN_DISABLE
+    high: TEGRA_PIN_ENABLE
+- nvidia,drive-type: Integer. Valid range 0...3.
+- nvidia,pull-down-strength: Integer. Controls drive strength. 0 is weakest.
+    The range of valid values depends on the pingroup. See "CAL_DRVDN" in the
+    Tegra TRM.
+- nvidia,pull-up-strength: Integer. Controls drive strength. 0 is weakest.
+    The range of valid values depends on the pingroup. See "CAL_DRVUP" in the
+    Tegra TRM.
+- nvidia,slew-rate-rising: Integer. Controls rising signal slew rate. 0 is
+    fastest. The range of valid values depends on the pingroup. See
+    "DRVDN_SLWR" in the Tegra TRM.
+- nvidia,slew-rate-falling: Integer. Controls falling signal slew rate. 0 is
+    fastest. The range of valid values depends on the pingroup. See
+    "DRVUP_SLWF" in the Tegra TRM.
+
+Valid values for pin and group names (nvidia,pin) are:
+
+  Mux groups:
+
+    These correspond to Tegra PINMUX_AUX_* (pinmux) registers. Any property
+    that exists in those registers may be set for the following pin names.
+
+    In Tegra210, many pins also have a dedicated APB_MISC_GP_*_PADCTRL
+    register. Where that is true, and property that exists in that register
+    may also be set on the following pin names.
+
+    als_prox_int_px3, ap_ready_pv5, ap_wake_bt_ph3, ap_wake_nfc_ph7,
+    aud_mclk_pbb0, batt_bcl, bt_rst_ph4, bt_wake_ap_ph5, button_home_py1,
+    button_power_on_px5, button_slide_sw_py0, button_vol_down_px7,
+    button_vol_up_px6, cam1_mclk_ps0, cam1_pwdn_ps7, cam1_strobe_pt1,
+    cam2_mclk_ps1, cam2_pwdn_pt0, cam_af_en_ps5, cam_flash_en_ps6,
+    cam_i2c_scl_ps2, cam_i2c_sda_ps3, cam_rst_ps4cam_rst_ps4, clk_32k_in,
+    clk_32k_out_py5, clk_req, core_pwr_req, cpu_pwr_req, dap1_din_pb1,
+    dap1_dout_pb2, dap1_fs_pb0, dap1_sclk_pb3, dap2_din_paa2, dap2_dout_paa3,
+    dap2_fs_paa0, dap2_sclk_paa1, dap4_din_pj5, dap4_dout_pj6, dap4_fs_pj4,
+    dap4_sclk_pj7, dmic1_clk_pe0, dmic1_dat_pe1, dmic2_clk_pe2, dmic2_dat_pe3,
+    dmic3_clk_pe4, dmic3_dat_pe5, dp_hpd0_pcc6, dvfs_clk_pbb2, dvfs_pwm_pbb1,
+    gen1_i2c_scl_pj1, gen1_i2c_sda_pj0, gen2_i2c_scl_pj2, gen2_i2c_sda_pj3,
+    gen3_i2c_scl_pf0, gen3_i2c_sda_pf1, gpio_x1_aud_pbb3, gpio_x3_aud_pbb4,
+    gps_en_pi2, gps_rst_pi3, hdmi_cec_pcc0, hdmi_int_dp_hpd_pcc1, jtag_rtck,
+    lcd_bl_en_pv1, lcd_bl_pwm_pv0, lcd_gpio1_pv3, lcd_gpio2_pv4, lcd_rst_pv2,
+    lcd_te_py2, modem_wake_ap_px0, motion_int_px2, nfc_en_pi0, nfc_int_pi1,
+    pa6, pcc7, pe6, pe7, pex_l0_clkreq_n_pa1, pex_l0_rst_n_pa0,
+    pex_l1_clkreq_n_pa4, pex_l1_rst_n_pa3, pex_wake_n_pa2, ph6, pk0, pk1, pk2,
+    pk3, pk4, pk5, pk6, pk7, pl0, pl1, pwr_i2c_scl_py3, pwr_i2c_sda_py4,
+    pwr_int_n, pz0, pz1, pz2, pz3, pz4, pz5, qspi_cs_n_pee1, qspi_io0_pee2,
+    qspi_io1_pee3, qspi_io2_pee4, qspi_io3_pee5, qspi_sck_pee0,
+    sata_led_active_pa5, sdmmc1_clk_pm0, sdmmc1_cmd_pm1, sdmmc1_dat0_pm5,
+    sdmmc1_dat1_pm4, sdmmc1_dat2_pm3, sdmmc1_dat3_pm2, sdmmc3_clk_pp0,
+    sdmmc3_cmd_pp1, sdmmc3_dat0_pp5, sdmmc3_dat1_pp4, sdmmc3_dat2_pp3,
+    sdmmc3_dat3_pp2, shutdown, spdif_in_pcc3, spdif_out_pcc2, spi1_cs0_pc3,
+    spi1_cs1_pc4, spi1_miso_pc1, spi1_mosi_pc0, spi1_sck_pc2, spi2_cs0_pb7,
+    spi2_cs1_pdd0, spi2_miso_pb5, spi2_mosi_pb4, spi2_sck_pb6, spi4_cs0_pc6,
+    spi4_miso_pd0, spi4_mosi_pc7, spi4_sck_pc5, temp_alert_px4, touch_clk_pv7,
+    touch_int_px1, touch_rst_pv6, uart1_cts_pu3, uart1_rts_pu2, uart1_rx_pu1,
+    uart1_tx_pu0, uart2_cts_pg3, uart2_rts_pg2, uart2_rx_pg1, uart2_tx_pg0,
+    uart3_cts_pd4, uart3_rts_pd3, uart3_rx_pd2, uart3_tx_pd1, uart4_cts_pi7,
+    uart4_rts_pi6, uart4_rx_pi5, uart4_tx_pi4, usb_vbus_en0_pcc4,
+    usb_vbus_en1_pcc5, wifi_en_ph0, wifi_rst_ph1, wifi_wake_ap_ph2
+
+  Drive groups:
+
+    These correspond to the Tegra APB_MISC_GP_*_PADCTRL (pad control)
+    registers. Note that where one of these registers controls a single pin
+    for which a PINMUX_AUX_* exists, see the list above for the pin name to
+    use when configuring the pinmux.
+
+    pa6, pcc7, pe6, pe7, ph6, pk0, pk1, pk2, pk3, pk4, pk5, pk6, pk7, pl0, pl1,
+    pz0, pz1, pz2, pz3, pz4, pz5, sdmmc1, sdmmc2, sdmmc3, sdmmc4
+
+Valid values for nvidia,functions are:
+
+    aud, bcl, blink, ccla, cec, cldvfs, clk, core, cpu, displaya, displayb,
+    dmic1, dmic2, dmic3, dp, dtv, extperiph3, i2c1, i2c2, i2c3, i2cpmu, i2cvi,
+    i2s1, i2s2, i2s3, i2s4a, i2s4b, i2s5a, i2s5b, iqc0, iqc1, jtag, pe, pe0,
+    pe1, pmi, pwm0, pwm1, pwm2, pwm3, qspi, rsvd0, rsvd1, rsvd2, rsvd3, sata,
+    sdmmc1, sdmmc3, shutdown, soc, sor0, sor1, spdif, spi1, spi2, spi3, spi4,
+    sys, touch, uart, uarta, uartb, uartc, uartd, usb, vgp1, vgp2, vgp3, vgp4,
+    vgp5, vgp6, vimclk, vimclk2
+
+Example:
+
+	pinmux: pinmux@70000800 {
+		compatible = "nvidia,tegra210-pinmux";
+		reg = <0x0 0x700008d4 0x0 0x2a8>, /* Pad control registers */
+		      <0x0 0x70003000 0x0 0x1000>; /* Mux registers */
+
+		pinctrl-names = "boot";
+		pinctrl-0 = <&state_boot>;
+
+		state_boot: pinmux {
+			gen1_i2c_scl_pj1 {
+				nvidia,pins = "gen1_i2c_scl_pj1",
+				nvidia,function = "i2c1";
+				nvidia,pull = <TEGRA_PIN_PULL_NONE>;
+				nvidia,tristate = <TEGRA_PIN_DISABLE>;
+				nvidia,enable-input = <TEGRA_PIN_ENABLE>;
+				nvidia,open-drain = <TEGRA_PIN_ENABLE>;
+				nvidia,io-hv = <TEGRA_PIN_ENABLE>;
+			};
+		};
+	};
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
index 47d84b6ee91b..b73c96d24f59 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt
@@ -38,7 +38,7 @@ property exists to define the pin configuration. Each state may also be
 assigned a name. When names are used, another property exists to map from
 those names to the integer IDs.
 
-Each client device's own binding determines the set of states the must be
+Each client device's own binding determines the set of states that must be
 defined in its device tree node, and whether to define the set of state
 IDs that must be provided, or whether to define the set of state names that
 must be provided.
@@ -133,16 +133,27 @@ pin multiplexing nodes:
 
 function		- the mux function to select
 groups			- the list of groups to select with this function
+			  (either this or "pins" must be specified)
+pins			- the list of pins to select with this function (either
+			  this or "groups" must be specified)
 
 Example:
 
 state_0_node_a {
-	function = "uart0";
-	groups = "u0rxtx", "u0rtscts";
+	uart0 {
+		function = "uart0";
+		groups = "u0rxtx", "u0rtscts";
+	};
 };
 state_1_node_a {
-	function = "spi0";
-	groups = "spi0pins";
+	spi0 {
+		function = "spi0";
+		groups = "spi0pins";
+	};
+};
+state_2_node_a {
+	function = "i2c0";
+	pins = "mfio29", "mfio30";
 };
 
 == Generic pin configuration node content ==
@@ -188,16 +199,22 @@ slew-rate		- set the slew rate
 For example:
 
 state_0_node_a {
-	pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
-	bias-pull-up;
+	cts_rxd {
+		pins = "GPIO0_AJ5", "GPIO2_AH4"; /* CTS+RXD */
+		bias-pull-up;
+	};
 };
 state_1_node_a {
-	pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */
-	output-high;
+	rts_txd {
+		pins = "GPIO1_AJ3", "GPIO3_AH3"; /* RTS+TXD */
+		output-high;
+	};
 };
 state_2_node_a {
-	group = "foo-group";
-	bias-pull-up;
+	foo {
+		group = "foo-group";
+		bias-pull-up;
+	};
 };
 
 Some of the generic properties take arguments. For those that do, the
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt
new file mode 100644
index 000000000000..5868a0f7255d
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt65xx.txt
@@ -0,0 +1,145 @@
+* Mediatek MT65XX Pin Controller
+
+The Mediatek's Pin controller is used to control SoC pins.
+
+Required properties:
+- compatible: value should be either of the following.
+    (a) "mediatek,mt8135-pinctrl", compatible with mt8135 pinctrl.
+- mediatek,pctl-regmap: Should be a phandle of the syscfg node.
+- pins-are-numbered: Specify the subnodes are using numbered pinmux to
+  specify pins.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells: number of cells in GPIO specifier. Since the generic GPIO
+  binding is used, the amount of cells must be specified as 2. See the below
+  mentioned gpio binding representation for description of particular cells.
+
+	Eg: <&pio 6 0>
+	<[phandle of the gpio controller node]
+	[line number within the gpio controller]
+	[flags]>
+
+	Values for gpio specifier:
+	- Line number: is a value between 0 to 202.
+	- Flags:  bit field of flags, as defined in <dt-bindings/gpio/gpio.h>.
+            Only the following flags are supported:
+            0 - GPIO_ACTIVE_HIGH
+            1 - GPIO_ACTIVE_LOW
+- reg: physicall address base for EINT registers
+- interrupt-controller: Marks the device node as an interrupt controller
+- #interrupt-cells: Should be two.
+- interrupts : The interrupt outputs from the controller.
+
+Please refer to pinctrl-bindings.txt in this directory for details of the
+common pinctrl bindings used by client devices.
+
+Subnode format
+A pinctrl node should contain at least one subnodes representing the
+pinctrl groups available on the machine. Each subnode will list the
+pins it needs, and how they should be configured, with regard to muxer
+configuration, pullups, drive strength, input enable/disable and input schmitt.
+
+    node {
+	pinmux = <PIN_NUMBER_PINMUX>;
+	GENERIC_PINCONFIG;
+    };
+
+Required properties:
+- pinmux: integer array, represents gpio pin number and mux setting.
+    Supported pin number and mux varies for different SoCs, and are defined
+    as macros in boot/dts/<soc>-pinfunc.h directly.
+
+Optional properties:
+- GENERIC_PINCONFIG: is the generic pinconfig options to use, bias-disable,
+    bias-pull-down, bias-pull-up, input-enable, input-disable, output-low, output-high,
+    input-schmitt-enable, input-schmitt-disable and drive-strength are valid.
+
+    Some special pins have extra pull up strength, there are R0 and R1 pull-up
+    resistors available, but for user, it's only need to set R1R0 as 00, 01, 10 or 11.
+    So when config bias-pull-up, it support arguments for those special pins.
+    Some macros have been defined for this usage, such as MTK_PUPD_SET_R1R0_00.
+    See dt-bindings/pinctrl/mt65xx.h.
+
+    When config drive-strength, it can support some arguments, such as
+    MTK_DRIVE_4mA, MTK_DRIVE_6mA, etc. See dt-bindings/pinctrl/mt65xx.h.
+
+Examples:
+
+#include "mt8135-pinfunc.h"
+
+...
+{
+	syscfg_pctl_a: syscfg_pctl_a@10005000 {
+		compatible = "mediatek,mt8135-pctl-a-syscfg", "syscon";
+		reg = <0 0x10005000 0 0x1000>;
+	};
+
+	syscfg_pctl_b: syscfg_pctl_b@1020C020 {
+		compatible = "mediatek,mt8135-pctl-b-syscfg", "syscon";
+		reg = <0 0x1020C020 0 0x1000>;
+	};
+
+	pinctrl@01c20800 {
+		compatible = "mediatek,mt8135-pinctrl";
+		reg = <0 0x1000B000 0 0x1000>;
+		mediatek,pctl-regmap = <&syscfg_pctl_a &syscfg_pctl_b>;
+		pins-are-numbered;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>,
+				<GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>;
+
+		i2c0_pins_a: i2c0@0 {
+			pins1 {
+				pinmux = <MT8135_PIN_100_SDA0__FUNC_SDA0>,
+					 <MT8135_PIN_101_SCL0__FUNC_SCL0>;
+				bias-disable;
+			};
+		};
+
+		i2c1_pins_a: i2c1@0 {
+			pins {
+				pinmux = <MT8135_PIN_195_SDA1__FUNC_SDA1>,
+					 <MT8135_PIN_196_SCL1__FUNC_SCL1>;
+				bias-pull-up = <55>;
+			};
+		};
+
+		i2c2_pins_a: i2c2@0 {
+			pins1 {
+				pinmux = <MT8135_PIN_193_SDA2__FUNC_SDA2>;
+				bias-pull-down;
+			};
+
+			pins2 {
+				pinmux = <MT8135_PIN_49_WATCHDOG__FUNC_GPIO49>;
+				bias-pull-up;
+			};
+		};
+
+		i2c3_pins_a: i2c3@0 {
+			pins1 {
+				pinmux = <MT8135_PIN_40_DAC_CLK__FUNC_GPIO40>,
+					 <MT8135_PIN_41_DAC_WS__FUNC_GPIO41>;
+				bias-pull-up = <55>;
+			};
+
+			pins2 {
+				pinmux = <MT8135_PIN_35_SCL3__FUNC_SCL3>,
+					 <MT8135_PIN_36_SDA3__FUNC_SDA3>;
+				output-low;
+				bias-pull-up = <55>;
+			};
+
+			pins3 {
+				pinmux = <MT8135_PIN_57_JTCK__FUNC_GPIO57>,
+					 <MT8135_PIN_60_JTDI__FUNC_JTDI>;
+				drive-strength = <32>;
+			};
+		};
+
+		...
+	}
+};
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
index 7ed08048516a..1ae63c0acd40 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
@@ -10,6 +10,7 @@ PMIC's from Qualcomm.
 		    "qcom,pm8018-gpio"
 		    "qcom,pm8038-gpio"
 		    "qcom,pm8058-gpio"
+		    "qcom,pm8916-gpio"
 		    "qcom,pm8917-gpio"
 		    "qcom,pm8921-gpio"
 		    "qcom,pm8941-gpio"
@@ -74,6 +75,7 @@ to specify in a pin configuration subnode:
 		    gpio1-gpio6 for pm8018
 		    gpio1-gpio12 for pm8038
 		    gpio1-gpio40 for pm8058
+		    gpio1-gpio4 for pm8916
 		    gpio1-gpio38 for pm8917
 		    gpio1-gpio44 for pm8921
 		    gpio1-gpio36 for pm8941
diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
index 854774b194ed..ed19991aad35 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-mpp.txt
@@ -8,6 +8,7 @@ of PMIC's from Qualcomm.
 	Value type: <string>
 	Definition: Should contain one of:
 		    "qcom,pm8841-mpp",
+		    "qcom,pm8916-mpp",
 		    "qcom,pm8941-mpp",
 		    "qcom,pma8084-mpp",
 
@@ -67,6 +68,7 @@ to specify in a pin configuration subnode:
 	Definition: List of MPP pins affected by the properties specified in
 		    this subnode.  Valid pins are:
 		    mpp1-mpp4 for pm8841
+		    mpp1-mpp4 for pm8916
 		    mpp1-mpp8 for pm8941
 		    mpp1-mpp4 for pma8084