diff options
| author | Linus Torvalds <torvalds@linux-foundation.org> | 2014-04-05 15:29:04 -0700 |
|---|---|---|
| committer | Linus Torvalds <torvalds@linux-foundation.org> | 2014-04-05 15:29:04 -0700 |
| commit | f83ccb93585d1f472c30fa2bbb8b56c23dbdb506 (patch) | |
| tree | 6548d92ff3f362f590bc96129df3e5cb5170ac02 | |
| parent | 930b440cd8256f3861bdb0a59d26efaadac7941a (diff) | |
| parent | 50b4af414d414af9e4df6f64e613bb0ffe581055 (diff) | |
| download | linux-f83ccb93585d1f472c30fa2bbb8b56c23dbdb506.tar.gz | |
Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann: "A large part of the arm-soc patches are nowadays DT changes, adding support for new SoCs, boards and devices without changing kernel source. The plan is still to move the devicetree files out of the kernel tree and reduce the amount of churn going on here, but we keep finding reasons to delay doing that. Changes are really all over the place, with little sticking out particularly. We have contributions from a total of 116 people in this branch. Unfortunately, the size of this branch also causes a significant number of conflicts at the moment, typically when subsystem maintainers merge patches that change the driver at the same time as the dts files. In most cases this could be avoided because the dts changes are supposed to be compatible in both ways, and we are asking everyone to send ARM dts changes through our tree only" * tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits) dts: stmmac: Document the clocks property in the stmmac base document dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac. ARM: STi: stih41x: Add support for the FSM Serial Flash Controller ARM: STi: stih416: Add support for the FSM Serial Flash Controller ARM: tegra: fix Dalmore pinctrl configuration ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND ARM: dts: Build all keystone dt blobs ARM: dts: keystone: Fix control register range for clktsip ARM: dts: keystone: Fix domain register range for clkfftc1 ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap ARM: dts: bcm21664: Add device tree files. ARM: DT: bcm21664: Device tree bindings ARM: efm32: properly namespace i2c location property ARM: efm32: fix unit address part in USART2 device nodes' names ARM: mvebu: Enable NAND controller in Armada 385-DB ARM: mvebu: Add support for NAND controller in Armada 38x SoC ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs ...
372 files changed, 31308 insertions, 6243 deletions
diff --git a/Documentation/devicetree/bindings/arm/bcm/bcm21664.txt b/Documentation/devicetree/bindings/arm/bcm/bcm21664.txt new file mode 100644 index 000000000000..e0774255e1a6 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/bcm21664.txt @@ -0,0 +1,15 @@ +Broadcom BCM21664 device tree bindings +-------------------------------------- + +This document describes the device tree bindings for boards with the BCM21664 +SoC. + +Required root node property: + - compatible: brcm,bcm21664 + +Example: + / { + model = "BCM21664 SoC"; + compatible = "brcm,bcm21664"; + [...] + } diff --git a/Documentation/devicetree/bindings/arm/bcm/kona-resetmgr.txt b/Documentation/devicetree/bindings/arm/bcm/kona-resetmgr.txt new file mode 100644 index 000000000000..93f31ca1ef4b --- /dev/null +++ b/Documentation/devicetree/bindings/arm/bcm/kona-resetmgr.txt @@ -0,0 +1,14 @@ +Broadcom Kona Family Reset Manager +---------------------------------- + +The reset manager is used on the Broadcom BCM21664 SoC. + +Required properties: + - compatible: brcm,bcm21664-resetmgr + - reg: memory address & range + +Example: + brcm,resetmgr@35001f00 { + compatible = "brcm,bcm21664-resetmgr"; + reg = <0x35001f00 0x24>; + }; diff --git a/Documentation/devicetree/bindings/arm/keystone/keystone.txt b/Documentation/devicetree/bindings/arm/keystone/keystone.txt index 63c0e6ae5cf7..59d7a46f85eb 100644 --- a/Documentation/devicetree/bindings/arm/keystone/keystone.txt +++ b/Documentation/devicetree/bindings/arm/keystone/keystone.txt @@ -8,3 +8,13 @@ Required properties: - compatible: All TI specific devices present in Keystone SOC should be in the form "ti,keystone-*". Generic devices like gic, arch_timers, ns16550 type UART should use the specified compatible for those devices. + +Boards: +- Keystone 2 Hawking/Kepler EVM + compatible = "ti,k2hk-evm","ti,keystone" + +- Keystone 2 Lamarr EVM + compatible = "ti,k2l-evm","ti,keystone" + +- Keystone 2 Edison EVM + compatible = "ti,k2e-evm","ti,keystone" diff --git a/Documentation/devicetree/bindings/arm/omap/dmm.txt b/Documentation/devicetree/bindings/arm/omap/dmm.txt new file mode 100644 index 000000000000..8bd6d0a238a8 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/omap/dmm.txt @@ -0,0 +1,22 @@ +OMAP Dynamic Memory Manager (DMM) bindings + +The dynamic memory manager (DMM) is a module located immediately in front of the +SDRAM controllers (called EMIFs on OMAP). DMM manages various aspects of memory +accesses such as priority generation amongst initiators, configuration of SDRAM +interleaving, optimizing transfer of 2D block objects, and provide MMU-like page +translation for initiators which need contiguous dma bus addresses. + +Required properties: +- compatible: Should contain "ti,omap4-dmm" for OMAP4 family + Should contain "ti,omap5-dmm" for OMAP5 and DRA7x family +- reg: Contains DMM register address range (base address and length) +- interrupts: Should contain an interrupt-specifier for DMM_IRQ. +- ti,hwmods: Name of the hwmod associated to DMM, which is typically "dmm" + +Example: + +dmm@4e000000 { + compatible = "ti,omap4-dmm"; + reg = <0x4e000000 0x800>; + ti,hwmods = "dmm"; +}; diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt index af9b4a0d902b..36ede19a1630 100644 --- a/Documentation/devicetree/bindings/arm/omap/omap.txt +++ b/Documentation/devicetree/bindings/arm/omap/omap.txt @@ -99,6 +99,9 @@ Boards: - OMAP4 PandaBoard : Low cost community board compatible = "ti,omap4-panda", "ti,omap4430" +- OMAP4 DuoVero with Parlor : Commercial expansion board with daughter board + compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4"; + - OMAP3 EVM : Software Development Board for OMAP35x, AM/DM37x compatible = "ti,omap3-evm", "ti,omap3" @@ -114,5 +117,8 @@ Boards: - AM43x EPOS EVM compatible = "ti,am43x-epos-evm", "ti,am4372", "ti,am43" +- AM437x GP EVM + compatible = "ti,am437x-gp-evm", "ti,am4372", "ti,am43" + - DRA7 EVM: Software Developement Board for DRA7XX compatible = "ti,dra7-evm", "ti,dra7" diff --git a/Documentation/devicetree/bindings/arm/samsung/pmu.txt b/Documentation/devicetree/bindings/arm/samsung/pmu.txt new file mode 100644 index 000000000000..f1f155255f28 --- /dev/null +++ b/Documentation/devicetree/bindings/arm/samsung/pmu.txt @@ -0,0 +1,15 @@ +SAMSUNG Exynos SoC series PMU Registers + +Properties: + - compatible : should contain two values. First value must be one from following list: + - "samsung,exynos5250-pmu" - for Exynos5250 SoC, + - "samsung,exynos5420-pmu" - for Exynos5420 SoC. + second value must be always "syscon". + + - reg : offset and length of the register set. + +Example : +pmu_system_controller: system-controller@10040000 { + compatible = "samsung,exynos5250-pmu", "syscon"; + reg = <0x10040000 0x5000>; +}; diff --git a/Documentation/devicetree/bindings/clock/exynos4-clock.txt b/Documentation/devicetree/bindings/clock/exynos4-clock.txt index a2ac2d9ac71a..f5a5b19ed3b2 100644 --- a/Documentation/devicetree/bindings/clock/exynos4-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos4-clock.txt @@ -15,259 +15,12 @@ Required Properties: - #clock-cells: should be 1. -The following is the list of clocks generated by the controller. Each clock is -assigned an identifier and client nodes use this identifier to specify the -clock which they consume. Some of the clocks are available only on a particular -Exynos4 SoC and this is specified where applicable. - - - [Core Clocks] - - Clock ID SoC (if specific) - ----------------------------------------------- - - xxti 1 - xusbxti 2 - fin_pll 3 - fout_apll 4 - fout_mpll 5 - fout_epll 6 - fout_vpll 7 - sclk_apll 8 - sclk_mpll 9 - sclk_epll 10 - sclk_vpll 11 - arm_clk 12 - aclk200 13 - aclk100 14 - aclk160 15 - aclk133 16 - mout_mpll_user_t 17 Exynos4x12 - mout_mpll_user_c 18 Exynos4x12 - mout_core 19 - mout_apll 20 - - - [Clock Gate for Special Clocks] - - Clock ID SoC (if specific) - ----------------------------------------------- - - sclk_fimc0 128 - sclk_fimc1 129 - sclk_fimc2 130 - sclk_fimc3 131 - sclk_cam0 132 - sclk_cam1 133 - sclk_csis0 134 - sclk_csis1 135 - sclk_hdmi 136 - sclk_mixer 137 - sclk_dac 138 - sclk_pixel 139 - sclk_fimd0 140 - sclk_mdnie0 141 Exynos4412 - sclk_mdnie_pwm0 12 142 Exynos4412 - sclk_mipi0 143 - sclk_audio0 144 - sclk_mmc0 145 - sclk_mmc1 146 - sclk_mmc2 147 - sclk_mmc3 148 - sclk_mmc4 149 - sclk_sata 150 Exynos4210 - sclk_uart0 151 - sclk_uart1 152 - sclk_uart2 153 - sclk_uart3 154 - sclk_uart4 155 - sclk_audio1 156 - sclk_audio2 157 - sclk_spdif 158 - sclk_spi0 159 - sclk_spi1 160 - sclk_spi2 161 - sclk_slimbus 162 - sclk_fimd1 163 Exynos4210 - sclk_mipi1 164 Exynos4210 - sclk_pcm1 165 - sclk_pcm2 166 - sclk_i2s1 167 - sclk_i2s2 168 - sclk_mipihsi 169 Exynos4412 - sclk_mfc 170 - sclk_pcm0 171 - sclk_g3d 172 - sclk_pwm_isp 173 Exynos4x12 - sclk_spi0_isp 174 Exynos4x12 - sclk_spi1_isp 175 Exynos4x12 - sclk_uart_isp 176 Exynos4x12 - sclk_fimg2d 177 - - [Peripheral Clock Gates] - - Clock ID SoC (if specific) - ----------------------------------------------- - - fimc0 256 - fimc1 257 - fimc2 258 - fimc3 259 - csis0 260 - csis1 261 - jpeg 262 - smmu_fimc0 263 - smmu_fimc1 264 - smmu_fimc2 265 - smmu_fimc3 266 - smmu_jpeg 267 - vp 268 - mixer 269 - tvenc 270 Exynos4210 - hdmi 271 - smmu_tv 272 - mfc 273 - smmu_mfcl 274 - smmu_mfcr 275 - g3d 276 - g2d 277 - rotator 278 Exynos4210 - mdma 279 Exynos4210 - smmu_g2d 280 Exynos4210 - smmu_rotator 281 Exynos4210 - smmu_mdma 282 Exynos4210 - fimd0 283 - mie0 284 - mdnie0 285 Exynos4412 - dsim0 286 - smmu_fimd0 287 - fimd1 288 Exynos4210 - mie1 289 Exynos4210 - dsim1 290 Exynos4210 - smmu_fimd1 291 Exynos4210 - pdma0 292 - pdma1 293 - pcie_phy 294 - sata_phy 295 Exynos4210 - tsi 296 - sdmmc0 297 - sdmmc1 298 - sdmmc2 299 - sdmmc3 300 - sdmmc4 301 - sata 302 Exynos4210 - sromc 303 - usb_host 304 - usb_device 305 - pcie 306 - onenand 307 - nfcon 308 - smmu_pcie 309 - gps 310 - smmu_gps 311 - uart0 312 - uart1 313 - uart2 314 - uart3 315 - uart4 316 - i2c0 317 - i2c1 318 - i2c2 319 - i2c3 320 - i2c4 321 - i2c5 322 - i2c6 323 - i2c7 324 - i2c_hdmi 325 - tsadc 326 - spi0 327 - spi1 328 - spi2 329 - i2s1 330 - i2s2 331 - pcm0 332 - i2s0 333 - pcm1 334 - pcm2 335 - pwm 336 - slimbus 337 - spdif 338 - ac97 339 - modemif 340 - chipid 341 - sysreg 342 - hdmi_cec 343 - mct 344 - wdt 345 - rtc 346 - keyif 347 - audss 348 - mipi_hsi 349 Exynos4210 - mdma2 350 Exynos4210 - pixelasyncm0 351 - pixelasyncm1 352 - fimc_lite0 353 Exynos4x12 - fimc_lite1 354 Exynos4x12 - ppmuispx 355 Exynos4x12 - ppmuispmx 356 Exynos4x12 - fimc_isp 357 Exynos4x12 - fimc_drc 358 Exynos4x12 - fimc_fd 359 Exynos4x12 - mcuisp 360 Exynos4x12 - gicisp 361 Exynos4x12 - smmu_isp 362 Exynos4x12 - smmu_drc 363 Exynos4x12 - smmu_fd 364 Exynos4x12 - smmu_lite0 365 Exynos4x12 - smmu_lite1 366 Exynos4x12 - mcuctl_isp 367 Exynos4x12 - mpwm_isp 368 Exynos4x12 - i2c0_isp 369 Exynos4x12 - i2c1_isp 370 Exynos4x12 - mtcadc_isp 371 Exynos4x12 - pwm_isp 372 Exynos4x12 - wdt_isp 373 Exynos4x12 - uart_isp 374 Exynos4x12 - asyncaxim 375 Exynos4x12 - smmu_ispcx 376 Exynos4x12 - spi0_isp 377 Exynos4x12 - spi1_isp 378 Exynos4x12 - pwm_isp_sclk 379 Exynos4x12 - spi0_isp_sclk 380 Exynos4x12 - spi1_isp_sclk 381 Exynos4x12 - uart_isp_sclk 382 Exynos4x12 - tmu_apbif 383 - - [Mux Clocks] - - Clock ID SoC (if specific) - ----------------------------------------------- - - mout_fimc0 384 - mout_fimc1 385 - mout_fimc2 386 - mout_fimc3 387 - mout_cam0 388 - mout_cam1 389 - mout_csis0 390 - mout_csis1 391 - mout_g3d0 392 - mout_g3d1 393 - mout_g3d 394 - aclk400_mcuisp 395 Exynos4x12 - - [Div Clocks] - - Clock ID SoC (if specific) - ----------------------------------------------- - - div_isp0 450 Exynos4x12 - div_isp1 451 Exynos4x12 - div_mcuisp0 452 Exynos4x12 - div_mcuisp1 453 Exynos4x12 - div_aclk200 454 Exynos4x12 - div_aclk400_mcuisp 455 Exynos4x12 +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos4.h header and can be used in device +tree sources. Example 1: An example of a clock controller node is listed below. @@ -285,6 +38,6 @@ Example 2: UART controller node that consumes the clock generated by the clock compatible = "samsung,exynos4210-uart"; reg = <0x13820000 0x100>; interrupts = <0 54 0>; - clocks = <&clock 314>, <&clock 153>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; }; diff --git a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt index 72ce617dea82..536eacd1063f 100644 --- a/Documentation/devicetree/bindings/clock/exynos5250-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5250-clock.txt @@ -13,163 +13,12 @@ Required Properties: - #clock-cells: should be 1. -The following is the list of clocks generated by the controller. Each clock is -assigned an identifier and client nodes use this identifier to specify the -clock which they consume. - - - [Core Clocks] - - Clock ID - ---------------------------- - - fin_pll 1 - - [Clock Gate for Special Clocks] - - Clock ID - ---------------------------- - - sclk_cam_bayer 128 - sclk_cam0 129 - sclk_cam1 130 - sclk_gscl_wa 131 - sclk_gscl_wb 132 - sclk_fimd1 133 - sclk_mipi1 134 - sclk_dp 135 - sclk_hdmi 136 - sclk_pixel 137 - sclk_audio0 138 - sclk_mmc0 139 - sclk_mmc1 140 - sclk_mmc2 141 - sclk_mmc3 142 - sclk_sata 143 - sclk_usb3 144 - sclk_jpeg 145 - sclk_uart0 146 - sclk_uart1 147 - sclk_uart2 148 - sclk_uart3 149 - sclk_pwm 150 - sclk_audio1 151 - sclk_audio2 152 - sclk_spdif 153 - sclk_spi0 154 - sclk_spi1 155 - sclk_spi2 156 - div_i2s1 157 - div_i2s2 158 - sclk_hdmiphy 159 - div_pcm0 160 - - - [Peripheral Clock Gates] - - Clock ID - ---------------------------- - - gscl0 256 - gscl1 257 - gscl2 258 - gscl3 259 - gscl_wa 260 - gscl_wb 261 - smmu_gscl0 262 - smmu_gscl1 263 - smmu_gscl2 264 - smmu_gscl3 265 - mfc 266 - smmu_mfcl 267 - smmu_mfcr 268 - rotator 269 - jpeg 270 - mdma1 271 - smmu_rotator 272 - smmu_jpeg 273 - smmu_mdma1 274 - pdma0 275 - pdma1 276 - sata 277 - usbotg 278 - mipi_hsi 279 - sdmmc0 280 - sdmmc1 281 - sdmmc2 282 - sdmmc3 283 - sromc 284 - usb2 285 - usb3 286 - sata_phyctrl 287 - sata_phyi2c 288 - uart0 289 - uart1 290 - uart2 291 - uart3 292 - uart4 293 - i2c0 294 - i2c1 295 - i2c2 296 - i2c3 297 - i2c4 298 - i2c5 299 - i2c6 300 - i2c7 301 - i2c_hdmi 302 - adc 303 - spi0 304 - spi1 305 - spi2 306 - i2s1 307 - i2s2 308 - pcm1 309 - pcm2 310 - pwm 311 - spdif 312 - ac97 313 - hsi2c0 314 - hsi2c1 315 - hs12c2 316 - hs12c3 317 - chipid 318 - sysreg 319 - pmu 320 - cmu_top 321 - cmu_core 322 - cmu_mem 323 - tzpc0 324 - tzpc1 325 - tzpc2 326 - tzpc3 327 - tzpc4 328 - tzpc5 329 - tzpc6 330 - tzpc7 331 - tzpc8 332 - tzpc9 333 - hdmi_cec 334 - mct 335 - wdt 336 - rtc 337 - tmu 338 - fimd1 339 - mie1 340 - dsim0 341 - dp 342 - mixer 343 - hdmi 344 - g2d 345 - mdma0 346 - smmu_mdma0 347 - - - [Clock Muxes] - - Clock ID - ---------------------------- - mout_hdmi 1024 +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5250.h header and can be used in device +tree sources. Example 1: An example of a clock controller node is listed below. @@ -187,6 +36,6 @@ Example 2: UART controller node that consumes the clock generated by the clock compatible = "samsung,exynos4210-uart"; reg = <0x13820000 0x100>; interrupts = <0 54 0>; - clocks = <&clock 314>, <&clock 153>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; }; diff --git a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt index 458f34789e5d..ca88c97a8562 100644 --- a/Documentation/devicetree/bindings/clock/exynos5420-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5420-clock.txt @@ -13,184 +13,12 @@ Required Properties: - #clock-cells: should be 1. -The following is the list of clocks generated by the controller. Each clock is -assigned an identifier and client nodes use this identifier to specify the -clock which they consume. +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. - - [Core Clocks] - - Clock ID - ---------------------------- - - fin_pll 1 - - [Clock Gate for Special Clocks] - - Clock ID - ---------------------------- - sclk_uart0 128 - sclk_uart1 129 - sclk_uart2 130 - sclk_uart3 131 - sclk_mmc0 132 - sclk_mmc1 133 - sclk_mmc2 134 - sclk_spi0 135 - sclk_spi1 136 - sclk_spi2 137 - sclk_i2s1 138 - sclk_i2s2 139 - sclk_pcm1 140 - sclk_pcm2 141 - sclk_spdif 142 - sclk_hdmi 143 - sclk_pixel 144 - sclk_dp1 145 - sclk_mipi1 146 - sclk_fimd1 147 - sclk_maudio0 148 - sclk_maupcm0 149 - sclk_usbd300 150 - sclk_usbd301 151 - sclk_usbphy300 152 - sclk_usbphy301 153 - sclk_unipro 154 - sclk_pwm 155 - sclk_gscl_wa 156 - sclk_gscl_wb 157 - sclk_hdmiphy 158 - - [Peripheral Clock Gates] - - Clock ID - ---------------------------- - - aclk66_peric 256 - uart0 257 - uart1 258 - uart2 259 - uart3 260 - i2c0 261 - i2c1 262 - i2c2 263 - i2c3 264 - i2c4 265 - i2c5 266 - i2c6 267 - i2c7 268 - i2c_hdmi 269 - tsadc 270 - spi0 271 - spi1 272 - spi2 273 - keyif 274 - i2s1 275 - i2s2 276 - pcm1 277 - pcm2 278 - pwm 279 - spdif 280 - i2c8 281 - i2c9 282 - i2c10 283 - aclk66_psgen 300 - chipid 301 - sysreg 302 - tzpc0 303 - tzpc1 304 - tzpc2 305 - tzpc3 306 - tzpc4 307 - tzpc5 308 - tzpc6 309 - tzpc7 310 - tzpc8 311 - tzpc9 312 - hdmi_cec 313 - seckey 314 - mct 315 - wdt 316 - rtc 317 - tmu 318 - tmu_gpu 319 - pclk66_gpio 330 - aclk200_fsys2 350 - mmc0 351 - mmc1 352 - mmc2 353 - sromc 354 - ufs 355 - aclk200_fsys 360 - tsi 361 - pdma0 362 - pdma1 363 - rtic 364 - usbh20 365 - usbd300 366 - usbd301 377 - aclk400_mscl 380 - mscl0 381 - mscl1 382 - mscl2 383 - smmu_mscl0 384 - smmu_mscl1 385 - smmu_mscl2 386 - aclk333 400 - mfc 401 - smmu_mfcl 402 - smmu_mfcr 403 - aclk200_disp1 410 - dsim1 411 - dp1 412 - hdmi 413 - aclk300_disp1 420 - fimd1 421 - smmu_fimd1 422 - aclk166 430 - mixer 431 - aclk266 440 - rotator 441 - mdma1 442 - smmu_rotator 443 - smmu_mdma1 444 - aclk300_jpeg 450 - jpeg 451 - jpeg2 452 - smmu_jpeg 453 - aclk300_gscl 460 - smmu_gscl0 461 - smmu_gscl1 462 - gscl_wa 463 - gscl_wb 464 - gscl0 465 - gscl1 466 - clk_3aa 467 - aclk266_g2d 470 - sss 471 - slim_sss 472 - mdma0 473 - aclk333_g2d 480 - g2d 481 - aclk333_432_gscl 490 - smmu_3aa 491 - smmu_fimcl0 492 - smmu_fimcl1 493 - smmu_fimcl3 494 - fimc_lite3 495 - aclk_g3d 500 - g3d 501 - smmu_mixer 502 - - Mux ID - ---------------------------- - - mout_hdmi 640 - - Divider ID - ---------------------------- - - dout_pixel 768 +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5420.h header and can be used in device +tree sources. Example 1: An example of a clock controller node is listed below. @@ -208,6 +36,6 @@ Example 2: UART controller node that consumes the clock generated by the clock compatible = "samsung,exynos4210-uart"; reg = <0x13820000 0x100>; interrupts = <0 54 0>; - clocks = <&clock 259>, <&clock 130>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; }; diff --git a/Documentation/devicetree/bindings/clock/exynos5440-clock.txt b/Documentation/devicetree/bindings/clock/exynos5440-clock.txt index 9955dc9c7d96..5f7005f73058 100644 --- a/Documentation/devicetree/bindings/clock/exynos5440-clock.txt +++ b/Documentation/devicetree/bindings/clock/exynos5440-clock.txt @@ -12,45 +12,12 @@ Required Properties: - #clock-cells: should be 1. -The following is the list of clocks generated by the controller. Each clock is -assigned an identifier and client nodes use this identifier to specify the -clock which they consume. - - - [Core Clocks] - - Clock ID - ---------------------------- - - xtal 1 - arm_clk 2 - - [Peripheral Clock Gates] - - Clock ID - ---------------------------- - - spi_baud 16 - pb0_250 17 - pr0_250 18 - pr1_250 19 - b_250 20 - b_125 21 - b_200 22 - sata 23 - usb 24 - gmac0 25 - cs250 26 - pb0_250_o 27 - pr0_250_o 28 - pr1_250_o 29 - b_250_o 30 - b_125_o 31 - b_200_o 32 - sata_o 33 - usb_o 34 - gmac0_o 35 - cs250_o 36 +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. + +All available clocks are defined as preprocessor macros in +dt-bindings/clock/exynos5440.h header and can be used in device +tree sources. Example: An example of a clock controller node is listed below. diff --git a/Documentation/devicetree/bindings/i2c/trivial-devices.txt b/Documentation/devicetree/bindings/i2c/trivial-devices.txt index f47e56bcf78d..71724d026ffa 100644 --- a/Documentation/devicetree/bindings/i2c/trivial-devices.txt +++ b/Documentation/devicetree/bindings/i2c/trivial-devices.txt @@ -59,6 +59,7 @@ plx,pex8648 48-Lane, 12-Port PCI Express Gen 2 (5.0 GT/s) Switch ramtron,24c64 i2c serial eeprom (24cxx) ricoh,rs5c372a I2C bus SERIAL INTERFACE REAL-TIME CLOCK IC samsung,24ad0xd1 S524AD0XF1 (128K/256K-bit Serial EEPROM for Low Power) +sii,s35390a 2-wire CMOS real-time clock st-micro,24c256 i2c serial eeprom (24cxx) stm,m41t00 Serial Access TIMEKEEPER stm,m41t62 Serial real-time clock (RTC) with alarm diff --git a/Documentation/devicetree/bindings/arm/atmel-adc.txt b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt index 9a1175b46f49..0f813dec5e08 100644 --- a/Documentation/devicetree/bindings/arm/atmel-adc.txt +++ b/Documentation/devicetree/bindings/iio/adc/at91_adc.txt @@ -8,32 +8,32 @@ Required properties: - clock-names: tuple listing input clock names. Required elements: "adc_clk", "adc_op_clk". - clocks: phandles to input clocks. - - atmel,adc-channels-used: Bitmask of the channels muxed and enable for this + - atmel,adc-channels-used: Bitmask of the channels muxed and enabled for this device - atmel,adc-startup-time: Startup Time of the ADC in microseconds as defined in the datasheet - atmel,adc-vref: Reference voltage in millivolts for the conversions - - atmel,adc-res: List of resolution in bits supported by the ADC. List size + - atmel,adc-res: List of resolutions in bits supported by the ADC. List size must be two at least. - atmel,adc-res-names: Contains one identifier string for each resolution in atmel,adc-res property. "lowres" and "highres" identifiers are required. Optional properties: - - atmel,adc-use-external: Boolean to enable of external triggers + - atmel,adc-use-external-triggers: Boolean to enable the external triggers - atmel,adc-use-res: String corresponding to an identifier from atmel,adc-res-names property. If not specified, the highest resolution will be used. - atmel,adc-sleep-mode: Boolean to enable sleep mode when no conversion - atmel,adc-sample-hold-time: Sample and Hold Time in microseconds - - atmel,adc-ts-wires: Number of touch screen wires. Should be 4 or 5. If this - value is set, then adc driver will enable touch screen + - atmel,adc-ts-wires: Number of touchscreen wires. Should be 4 or 5. If this + value is set, then the adc driver will enable touchscreen support. - NOTE: when adc touch screen enabled, the adc hardware trigger will be - disabled. Since touch screen will occupied the trigger register. + NOTE: when adc touchscreen is enabled, the adc hardware trigger will be + disabled. Since touchscreen will occupy the trigger register. - atmel,adc-ts-pressure-threshold: a pressure threshold for touchscreen. It - make touch detect more precision. - + makes touch detection more precise. + Optional trigger Nodes: - Required properties: * trigger-name: Name of the trigger exposed to the user @@ -44,42 +44,43 @@ Optional trigger Nodes: Examples: adc0: adc@fffb0000 { + #address-cells = <1>; + #size-cells = <0>; compatible = "atmel,at91sam9260-adc"; reg = <0xfffb0000 0x100>; - interrupts = <20 4>; + interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; clocks = <&adc_clk>, <&adc_op_clk>; clock-names = "adc_clk", "adc_op_clk"; - atmel,adc-channel-base = <0x30>; atmel,adc-channels-used = <0xff>; - atmel,adc-drdy-mask = <0x10000>; - atmel,adc-num-channels = <8>; atmel,adc-startup-time = <40>; - atmel,adc-status-register = <0x1c>; - atmel,adc-trigger-register = <0x08>; - atmel,adc-use-external; + atmel,adc-use-external-triggers; atmel,adc-vref = <3300>; atmel,adc-res = <8 10>; atmel,adc-res-names = "lowres", "highres"; atmel,adc-use-res = "lowres"; trigger@0 { + reg = <0>; trigger-name = "external-rising"; trigger-value = <0x1>; trigger-external; }; trigger@1 { + reg = <1>; trigger-name = "external-falling"; trigger-value = <0x2>; trigger-external; }; trigger@2 { + reg = <2>; trigger-name = "external-any"; trigger-value = <0x3>; trigger-external; }; trigger@3 { + reg = <3>; trigger-name = "continuous"; trigger-value = <0x6>; }; diff --git a/Documentation/devicetree/bindings/net/socfpga-dwmac.txt b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt new file mode 100644 index 000000000000..636f0ac4e223 --- /dev/null +++ b/Documentation/devicetree/bindings/net/socfpga-dwmac.txt @@ -0,0 +1,27 @@ +Altera SOCFPGA SoC DWMAC controller + +This is a variant of the dwmac/stmmac driver an inherits all descriptions +present in Documentation/devicetree/bindings/net/stmmac.txt. + +The device node has additional properties: + +Required properties: + - compatible : Should contain "altr,socfpga-stmmac" along with + "snps,dwmac" and any applicable more detailed + designware version numbers documented in stmmac.txt + - altr,sysmgr-syscon : Should be the phandle to the system manager node that + encompasses the glue register, the register offset, and the register shift. + +Example: + +gmac0: ethernet@ff700000 { + compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; + altr,sysmgr-syscon = <&sysmgr 0x60 0>; + status = "disabled"; + reg = <0xff700000 0x2000>; + interrupts = <0 115 4>; + interrupt-names = "macirq"; + mac-address = [00 00 00 00 00 00];/* Filled in by U-Boot */ + clocks = <&emac_0_clk>; + clocks-names = "stmmaceth"; +}; diff --git a/Documentation/devicetree/bindings/net/stmmac.txt b/Documentation/devicetree/bindings/net/stmmac.txt index 5748351fb9df..80c1fb8bfbb8 100644 --- a/Documentation/devicetree/bindings/net/stmmac.txt +++ b/Documentation/devicetree/bindings/net/stmmac.txt @@ -31,6 +31,10 @@ Optional properties: - reset-names: Should contain the reset signal name "stmmaceth", if a reset phandle is given - max-frame-size: See ethernet.txt file in the same directory +- clocks: If present, the first clock should be the GMAC main clock, + further clocks may be specified in derived bindings. +- clocks-names: One name for each entry in the clocks property, the + first one should be "stmmaceth". Examples: @@ -43,4 +47,6 @@ Examples: mac-address = [000000000000]; /* Filled in by U-Boot */ max-frame-size = <3800>; phy-mode = "gmii"; + clocks = <&clock>; + clock-names = "stmmaceth">; }; diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt index 24cee06915c9..c300391e8d3e 100644 --- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -42,6 +42,10 @@ Required properties: - 0xc2000000: prefetchable memory region Please refer to the standard PCI bus binding document for a more detailed explanation. +- #interrupt-cells: Size representation for interrupts (must be 1) +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties + Please refer to the standard PCI bus binding document for a more detailed + explanation. - clocks: Must contain an entry for each entry in clock-names. See ../clocks/clock-bindings.txt for details. - clock-names: Must include the following entries: @@ -86,6 +90,10 @@ SoC DTSI: 0 99 0x04>; /* MSI interrupt */ interrupt-names = "intr", "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + bus-range = <0x00 0xff>; #address-cells = <3>; #size-cells = <2>; diff --git a/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt new file mode 100644 index 000000000000..5ab26b7e9d35 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/st,sti-powerdown.txt @@ -0,0 +1,47 @@ +STMicroelectronics STi family Sysconfig Peripheral Powerdown Reset Controller +============================================================================= + +This binding describes a reset controller device that is used to enable and +disable on-chip peripheral controllers such as USB and SATA, using +"powerdown" control bits found in the STi family SoC system configuration +registers. These have been grouped together into a single reset controller +device for convenience. + +The actual action taken when powerdown is asserted is hardware dependent. +However, when asserted it may not be possible to access the hardware's +registers and after an assert/deassert sequence the hardware's previous state +may no longer be valid. + +Please refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "st,<chip>-powerdown" + ex: "st,stih415-powerdown", "st,stih416-powerdown" +- #reset-cells: 1, see below + +example: + + powerdown: powerdown-controller { + #reset-cells = <1>; + compatible = "st,stih415-powerdown"; + }; + + +Specifying powerdown control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the powerdown device node and an +index specifying which channel to use, as described in reset.txt + +example: + + usb1: usb@fe200000 { + resets = <&powerdown STIH41X_USB1_POWERDOWN>; + }; + +Macro definitions for the supported reset channels can be found in: + +include/dt-bindings/reset-controller/stih415-resets.h +include/dt-bindings/reset-controller/stih416-resets.h diff --git a/Documentation/devicetree/bindings/reset/st,sti-softreset.txt b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt new file mode 100644 index 000000000000..a8d3d3c25ca2 --- /dev/null +++ b/Documentation/devicetree/bindings/reset/st,sti-softreset.txt @@ -0,0 +1,46 @@ +STMicroelectronics STi family Sysconfig Peripheral SoftReset Controller +============================================================================= + +This binding describes a reset controller device that is used to enable and +disable on-chip peripheral controllers such as USB and SATA, using +"softreset" control bits found in the STi family SoC system configuration +registers. + +The actual action taken when softreset is asserted is hardware dependent. +However, when asserted it may not be possible to access the hardware's +registers and after an assert/deassert sequence the hardware's previous state +may no longer be valid. + +Please refer to reset.txt in this directory for common reset +controller binding usage. + +Required properties: +- compatible: Should be "st,<chip>-softreset" example: + "st,stih415-softreset" or "st,stih416-softreset"; +- #reset-cells: 1, see below + +example: + + softreset: softreset-controller { + #reset-cells = <1>; + compatible = "st,stih415-softreset"; + }; + + +Specifying softreset control of devices +======================================= + +Device nodes should specify the reset channel required in their "resets" +property, containing a phandle to the softreset device node and an +index specifying which channel to use, as described in reset.txt + +example: + + ethernet0{ + resets = <&softreset STIH415_ETH0_SOFTRESET>; + }; + +Macro definitions for the supported reset channels can be found in: + +include/dt-bindings/reset-controller/stih415-resets.h +include/dt-bindings/reset-controller/stih416-resets.h diff --git a/Documentation/devicetree/bindings/usb/atmel-usb.txt b/Documentation/devicetree/bindings/usb/atmel-usb.txt index 55f51af08bc7..bc2222ca3f2a 100644 --- a/Documentation/devicetree/bindings/usb/atmel-usb.txt +++ b/Documentation/devicetree/bindings/usb/atmel-usb.txt @@ -57,8 +57,8 @@ Required properties: - ep childnode: To specify the number of endpoints and their properties. Optional properties: - - atmel,vbus-gpio: If present, specifies a gpio that needs to be - activated for the bus to be powered. + - atmel,vbus-gpio: If present, specifies a gpio that allows to detect whether + vbus is present (USB is connected). Required child node properties: - name: Name of the endpoint. diff --git a/Documentation/devicetree/bindings/usb/ehci-omap.txt b/Documentation/devicetree/bindings/usb/ehci-omap.txt index 485a9a1efa7a..3dc231c832b0 100644 --- a/Documentation/devicetree/bindings/usb/ehci-omap.txt +++ b/Documentation/devicetree/bindings/usb/ehci-omap.txt @@ -21,7 +21,7 @@ Documentation/devicetree/bindings/mfd/omap-usb-host.txt Example for OMAP4: usbhsehci: ehci@4a064c00 { - compatible = "ti,ehci-omap", "usb-ehci"; + compatible = "ti,ehci-omap"; reg = <0x4a064c00 0x400>; interrupts = <0 77 0x4>; }; diff --git a/Documentation/devicetree/bindings/usb/ohci-omap3.txt b/Documentation/devicetree/bindings/usb/ohci-omap3.txt index 14ab42812a8e..ce8c47cff6d0 100644 --- a/Documentation/devicetree/bindings/usb/ohci-omap3.txt +++ b/Documentation/devicetree/bindings/usb/ohci-omap3.txt @@ -9,7 +9,7 @@ Required properties: Example for OMAP4: usbhsohci: ohci@4a064800 { - compatible = "ti,ohci-omap3", "usb-ohci"; + compatible = "ti,ohci-omap3"; reg = <0x4a064800 0x400>; interrupts = <0 76 0x4>; }; diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 95465d57eb31..0f01c9bf19c8 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -35,11 +35,13 @@ dallas Maxim Integrated Products (formerly Dallas Semiconductor) davicom DAVICOM Semiconductor, Inc. dlink D-Link Systems, Inc. denx Denx Software Engineering +dmo Data Modul AG edt Emerging Display Technologies emmicro EM Microelectronic epfl Ecole Polytechnique Fédérale de Lausanne epson Seiko Epson Corp. est ESTeem Wireless Modems +eukrea Eukréa Electromatique fsl Freescale Semiconductor GEFanuc GE Fanuc Intelligent Platforms Embedded Systems, Inc. gef GE Fanuc Intelligent Platforms Embedded Systems, Inc. @@ -83,10 +85,12 @@ picochip Picochip Ltd powervr PowerVR (deprecated, use img) qca Qualcomm Atheros, Inc. qcom Qualcomm Technologies, Inc +qnap QNAP Systems, Inc. ralink Mediatek/Ralink Technology Corp. ramtron Ramtron International realtek Realtek Semiconductor Corp. renesas Renesas Electronics Corporation +ricoh Ricoh Co. Ltd. rockchip Fuzhou Rockchip Electronics Co., Ltd samsung Samsung Semiconductor sbs Smart Battery System @@ -94,6 +98,7 @@ schindler Schindler sil Silicon Image silabs Silicon Laboratories simtek +sii Seiko Instruments, Inc. sirf SiRF Technology, Inc. smsc Standard Microsystems Corporation snps Synopsys, Inc. @@ -101,12 +106,14 @@ spansion Spansion Inc. st STMicroelectronics ste ST-Ericsson stericsson ST-Ericsson +synology Synology, Inc. ti Texas Instruments tlm Trusted Logic Mobility toshiba Toshiba Corporation toumaz Toumaz v3 V3 Semiconductor via VIA Technologies, Inc. +voipac Voipac Technologies s.r.o. winbond Winbond Electronics corp. wlf Wolfson Microelectronics wm Wondermedia Technologies, Inc. diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 112813a80b71..35c146f31e46 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -51,19 +51,15 @@ dtb-$(CONFIG_ARCH_AT91) += sama5d36ek.dtb dtb-$(CONFIG_ARCH_ATLAS6) += atlas6-evb.dtb dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb -dtb-$(CONFIG_ARCH_BCM_MOBILE) += bcm11351-brt.dtb \ - bcm28155-ap.dtb +dtb-$(CONFIG_ARCH_BCM_MOBILE) += bcm28155-ap.dtb \ + bcm21664-garnet.dtb dtb-$(CONFIG_ARCH_BCM2835) += bcm2835-rpi-b.dtb +dtb-$(CONFIG_ARCH_BCM_5301X) += bcm4708-netgear-r6250.dtb dtb-$(CONFIG_ARCH_BERLIN) += \ berlin2-sony-nsz-gs7.dtb \ berlin2cd-google-chromecast.dtb dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \ da850-evm.dtb -dtb-$(CONFIG_MACH_DOVE) += dove-cm-a510.dtb \ - dove-cubox.dtb \ - dove-d2plug.dtb \ - dove-d3plug.dtb \ - dove-dove-db.dtb dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \ exynos4210-smdkv310.dtb \ @@ -86,7 +82,11 @@ dtb-$(CONFIG_ARCH_HIGHBANK) += highbank.dtb \ ecx-2000.dtb dtb-$(CONFIG_ARCH_INTEGRATOR) += integratorap.dtb \ integratorcp.dtb +dtb-$(CONFIG_ARCH_KEYSTONE) += k2hk-evm.dtb \ + k2l-evm.dtb \ + k2e-evm.dtb kirkwood := \ + kirkwood-b3.dtb \ kirkwood-cloudbox.dtb \ kirkwood-db-88f6281.dtb \ kirkwood-db-88f6282.dtb \ @@ -94,6 +94,18 @@ kirkwood := \ kirkwood-dns325.dtb \ kirkwood-dockstar.dtb \ kirkwood-dreamplug.dtb \ + kirkwood-ds109.dtb \ + kirkwood-ds110jv10.dtb \ + kirkwood-ds111.dtb \ + kirkwood-ds209.dtb \ + kirkwood-ds210.dtb \ + kirkwood-ds212.dtb \ + kirkwood-ds212j.dtb \ + kirkwood-ds409.dtb \ + kirkwood-ds409slim.dtb \ + kirkwood-ds411.dtb \ + kirkwood-ds411j.dtb \ + kirkwood-ds411slim.dtb \ kirkwood-goflexnet.dtb \ kirkwood-guruplug-server-plus.dtb \ kirkwood-ib62x0.dtb \ @@ -116,54 +128,74 @@ kirkwood := \ kirkwood-nsa310a.dtb \ kirkwood-openblocks_a6.dtb \ kirkwood-openblocks_a7.dtb \ + kirkwood-rd88f6192.dtb \ + kirkwood-rd88f6281-a0.dtb \ + kirkwood-rd88f6281-a1.dtb \ + kirkwood-rs212.dtb \ + kirkwood-rs409.dtb \ + kirkwood-rs411.dtb \ kirkwood-sheevaplug.dtb \ kirkwood-sheevaplug-esata.dtb \ + kirkwood-t5325.dtb \ kirkwood-topkick.dtb \ kirkwood-ts219-6281.dtb \ - kirkwood-ts219-6282.dtb + kirkwood-ts219-6282.dtb \ + kirkwood-ts419-6281.dtb \ + kirkwood-ts419-6282.dtb dtb-$(CONFIG_ARCH_KIRKWOOD) += $(kirkwood) dtb-$(CONFIG_MACH_KIRKWOOD) += $(kirkwood) dtb-$(CONFIG_ARCH_LPC32XX) += ea3250.dtb phy3250.dtb dtb-$(CONFIG_ARCH_MARCO) += marco-evb.dtb dtb-$(CONFIG_ARCH_MOXART) += moxart-uc7112lx.dtb -dtb-$(CONFIG_ARCH_MVEBU) += armada-370-db.dtb \ - armada-370-mirabox.dtb \ - armada-370-netgear-rn102.dtb \ - armada-370-netgear-rn104.dtb \ - armada-370-rd.dtb \ - armada-xp-axpwifiap.dtb \ - armada-xp-db.dtb \ - armada-xp-gp.dtb \ - armada-xp-netgear-rn2120.dtb \ - armada-xp-matrix.dtb \ - armada-xp-openblocks-ax3-4.dtb dtb-$(CONFIG_ARCH_MXC) += \ + imx25-eukrea-mbimxsd25-baseboard.dtb \ imx25-karo-tx25.dtb \ imx25-pdk.dtb \ imx27-apf27.dtb \ imx27-apf27dev.dtb \ imx27-pdk.dtb \ - imx27-phytec-phycore-som.dtb \ imx27-phytec-phycore-rdk.dtb \ - imx27-phytec-phycard-s-som.dtb \ imx27-phytec-phycard-s-rdk.dtb \ imx31-bug.dtb \ + imx35-eukrea-mbimxsd35-baseboard.dtb \ + imx50-evk.dtb \ imx51-apf51.dtb \ imx51-apf51dev.dtb \ imx51-babbage.dtb \ + imx51-eukrea-mbimxsd51-baseboard.dtb \ imx53-ard.dtb \ - imx53-evk.dtb \ imx53-m53evk.dtb \ imx53-mba53.dtb \ imx53-qsb.dtb \ + imx53-qsrb.dtb \ imx53-smd.dtb \ + imx53-tx53-x03x.dtb \ + imx53-tx53-x13x.dtb \ + imx53-voipac-bsb.dtb \ imx6dl-cubox-i.dtb \ + imx6dl-dfi-fs700-m60.dtb \ + imx6dl-gw51xx.dtb \ + imx6dl-gw52xx.dtb \ + imx6dl-gw53xx.dtb \ + imx6dl-gw54xx.dtb \ imx6dl-hummingboard.dtb \ + imx6dl-nitrogen6x.dtb \ imx6dl-sabreauto.dtb \ + imx6dl-sabrelite.dtb \ imx6dl-sabresd.dtb \ imx6dl-wandboard.dtb \ imx6q-arm2.dtb \ + imx6q-cm-fx6.dtb \ imx6q-cubox-i.dtb \ + imx6q-dfi-fs700-m60.dtb \ + imx6q-dmo-edmqmx6.dtb \ + imx6q-gk802.dtb \ + imx6q-gw51xx.dtb \ + imx6q-gw52xx.dtb \ + imx6q-gw53xx.dtb \ + imx6q-gw5400-a.dtb \ + imx6q-gw54xx.dtb \ + imx6q-nitrogen6x.dtb \ imx6q-phytec-pbab01.dtb \ imx6q-sabreauto.dtb \ imx6q-sabrelite.dtb \ @@ -187,6 +219,9 @@ dtb-$(CONFIG_ARCH_MXS) += imx23-evk.dtb \ imx28-cfa10056.dtb \ imx28-cfa10057.dtb \ imx28-cfa10058.dtb \ + imx28-duckbill.dtb \ + imx28-eukrea-mbmx283lc.dtb \ + imx28-eukrea-mbmx287lc.dtb \ imx28-evk.dtb \ imx28-m28cu3.dtb \ imx28-m28evk.dtb \ @@ -203,6 +238,10 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ omap2420-n810-wimax.dtb \ omap3430-sdp.dtb \ omap3-beagle.dtb \ + omap3-cm-t3517.dtb \ + omap3-sbc-t3517.dtb \ + omap3-cm-t3530.dtb \ + omap3-sbc-t3530.dtb \ omap3-cm-t3730.dtb \ omap3-sbc-t3730.dtb \ omap3-devkit8000.dtb \ @@ -213,12 +252,24 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ omap3-n900.dtb \ omap3-n9.dtb \ omap3-n950.dtb \ + omap3-overo-alto35.dtb \ + omap3-overo-storm-alto35.dtb \ + omap3-overo-chestnut43.dtb \ + omap3-overo-storm-chestnut43.dtb \ + omap3-overo-gallop43.dtb \ + omap3-overo-storm-gallop43.dtb \ + omap3-overo-palo43.dtb \ + omap3-overo-storm-palo43.dtb \ + omap3-overo-summit.dtb \ + omap3-overo-storm-summit.dtb \ omap3-overo-tobi.dtb \ omap3-overo-storm-tobi.dtb \ omap3-gta04.dtb \ omap3-igep0020.dtb \ omap3-igep0030.dtb \ + omap3-lilly-dbb056.dtb \ omap3-zoom3.dtb \ + omap4-duovero-parlor.dtb \ omap4-panda.dtb \ omap4-panda-a4.dtb \ omap4-panda-es.dtb \ @@ -232,9 +283,11 @@ dtb-$(CONFIG_ARCH_OMAP2PLUS) += omap2420-h4.dtb \ am335x-boneblack.dtb \ am335x-nano.dtb \ am335x-base0033.dtb \ + am3517-craneboard.dtb \ am3517-evm.dtb \ am3517_mt_ventoux.dtb \ am43x-epos-evm.dtb \ + am437x-gp-evm.dtb \ dra7-evm.dtb dtb-$(CONFIG_ARCH_ORION5X) += orion5x-lacie-ethernet-disk-mini-v2.dtb dtb-$(CONFIG_ARCH_PRIMA2) += prima2-evb.dtb @@ -291,6 +344,9 @@ dtb-$(CONFIG_ARCH_SUNXI) += \ sun4i-a10-cubieboard.dtb \ sun4i-a10-mini-xplus.dtb \ sun4i-a10-hackberry.dtb \ + sun4i-a10-inet97fv2.dtb \ + sun4i-a10-olinuxino-lime.dtb \ + sun4i-a10-pcduino.dtb \ sun5i-a10s-olinuxino-micro.dtb \ sun5i-a13-olinuxino.dtb \ sun5i-a13-olinuxino-micro.dtb \ @@ -329,6 +385,29 @@ dtb-$(CONFIG_ARCH_VT8500) += vt8500-bv07.dtb \ dtb-$(CONFIG_ARCH_ZYNQ) += zynq-zc702.dtb \ zynq-zc706.dtb \ zynq-zed.dtb +dtb-$(CONFIG_MACH_ARMADA_370) += \ + armada-370-db.dtb \ + armada-370-mirabox.dtb \ + armada-370-netgear-rn102.dtb \ + armada-370-netgear-rn104.dtb \ + armada-370-rd.dtb +dtb-$(CONFIG_MACH_ARMADA_375) += \ + armada-375-db.dtb +dtb-$(CONFIG_MACH_ARMADA_38X) += \ + armada-385-db.dtb \ + armada-385-rd.dtb +dtb-$(CONFIG_MACH_ARMADA_XP) += \ + armada-xp-axpwifiap.dtb \ + armada-xp-db.dtb \ + armada-xp-gp.dtb \ + armada-xp-netgear-rn2120.dtb \ + armada-xp-matrix.dtb \ + armada-xp-openblocks-ax3-4.dtb +dtb-$(CONFIG_MACH_DOVE) += dove-cm-a510.dtb \ + dove-cubox.dtb \ + dove-d2plug.dtb \ + dove-d3plug.dtb \ + dove-dove-db.dtb targets += dtbs dtbs_install targets += $(dtb-y) diff --git a/arch/arm/boot/dts/am335x-evm.dts b/arch/arm/boot/dts/am335x-evm.dts index 7e6c64ed966d..28ae040e7c3d 100644 --- a/arch/arm/boot/dts/am335x-evm.dts +++ b/arch/arm/boot/dts/am335x-evm.dts @@ -260,6 +260,12 @@ >; }; + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + >; + }; + lcd_pins_s0: lcd_pins_s0 { pinctrl-single,pins = < 0x20 0x01 /* gpmc_ad8.lcd_data16, OUTPUT | MODE1 */ @@ -434,9 +440,9 @@ ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ nand@0,0 { reg = <0 0 0>; /* CS0, offset 0 */ - nand-bus-width = <8>; ti,nand-ecc-opt = "bch8"; - gpmc,device-nand = "true"; + ti,elm-id = <&elm>; + nand-bus-width = <8>; gpmc,device-width = <1>; gpmc,sync-clk-ps = <0>; gpmc,cs-on-ns = <0>; @@ -460,50 +466,51 @@ gpmc,wait-monitoring-ns = <0>; gpmc,wr-access-ns = <40>; gpmc,wr-data-mux-bus-ns = <0>; - + /* MTD partition table */ + /* All SPL-* partitions are sized to minimal length + * which can be independently programmable. For + * NAND flash this is equal to size of erase-block */ #address-cells = <1>; #size-cells = <1>; - elm_id = <&elm>; - - /* MTD partition table */ partition@0 { - label = "SPL1"; + label = "NAND.SPL"; reg = <0x00000000 0x000020000>; }; - partition@1 { - label = "SPL2"; + label = "NAND.SPL.backup1"; reg = <0x00020000 0x00020000>; }; - partition@2 { - label = "SPL3"; + label = "NAND.SPL.backup2"; reg = <0x00040000 0x00020000>; }; - partition@3 { - label = "SPL4"; + label = "NAND.SPL.backup3"; reg = <0x00060000 0x00020000>; }; - partition@4 { - label = "U-boot"; - reg = <0x00080000 0x001e0000>; + label = "NAND.u-boot-spl"; + reg = <0x00080000 0x00040000>; }; - partition@5 { - label = "environment"; - reg = <0x00260000 0x00020000>; + label = "NAND.u-boot"; + reg = <0x000C0000 0x00100000>; }; - partition@6 { - label = "Kernel"; - reg = <0x00280000 0x00500000>; + label = "NAND.u-boot-env"; + reg = <0x001C0000 0x00020000>; }; - partition@7 { - label = "File-System"; - reg = <0x00780000 0x0F880000>; + label = "NAND.u-boot-env.backup1"; + reg = <0x001E0000 0x00020000>; + }; + partition@8 { + label = "NAND.kernel"; + reg = <0x00200000 0x00800000>; + }; + partition@9 { + label = "NAND.file-system"; + reg = <0x00A00000 0x0F600000>; }; }; }; @@ -643,6 +650,9 @@ status = "okay"; vmmc-supply = <&vmmc_reg>; bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; }; &sham { diff --git a/arch/arm/boot/dts/am335x-evmsk.dts b/arch/arm/boot/dts/am335x-evmsk.dts index 486880b74831..ec08f6f677c3 100644 --- a/arch/arm/boot/dts/am335x-evmsk.dts +++ b/arch/arm/boot/dts/am335x-evmsk.dts @@ -45,6 +45,18 @@ regulator-boot-on; }; + wl12xx_vmmc: fixedregulator@2 { + pinctrl-names = "default"; + pinctrl-0 = <&wl12xx_gpio>; + compatible = "regulator-fixed"; + regulator-name = "vwl1271"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio1 29 0>; + startup-delay-us = <70000>; + enable-active-high; + }; + leds { pinctrl-names = "default"; pinctrl-0 = <&user_leds_s0>; @@ -270,6 +282,24 @@ 0x144 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* rmii1_ref_clk.mcasp1_axr3 */ >; }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + 0x74 (PIN_INPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpio0_31 */ + 0x80 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn1.mmc1_clk */ + 0x84 (PIN_INPUT_PULLUP | MUX_MODE2) /* gpmc_csn2.mmc1_cmd */ + 0x00 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad0.mmc1_dat0 */ + 0x04 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad1.mmc1_dat1 */ + 0x08 (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad2.mmc1_dat2 */ + 0x0c (PIN_INPUT_PULLUP | MUX_MODE1) /* gpmc_ad3.mmc1_dat3 */ + >; + }; + + wl12xx_gpio: pinmux_wl12xx_gpio { + pinctrl-single,pins = < + 0x7c (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_csn0.gpio1_29 */ + >; + }; }; &uart0 { @@ -342,9 +372,22 @@ status = "okay"; }; + usb-phy@47401b00 { + status = "okay"; + }; + usb@47401000 { status = "okay"; }; + + usb@47401800 { + status = "okay"; + dr_mode = "host"; + }; + + dma-controller@07402000 { + status = "okay"; + }; }; &epwmss2 { @@ -440,6 +483,7 @@ pinctrl-names = "default", "sleep"; pinctrl-0 = <&cpsw_default>; pinctrl-1 = <&cpsw_sleep>; + dual_emac = <1>; }; &davinci_mdio { @@ -451,11 +495,13 @@ &cpsw_emac0 { phy_id = <&davinci_mdio>, <0>; phy-mode = "rgmii-txid"; + dual_emac_res_vlan = <1>; }; &cpsw_emac1 { phy_id = <&davinci_mdio>, <1>; phy-mode = "rgmii-txid"; + dual_emac_res_vlan = <2>; }; &mmc1 { @@ -479,6 +525,16 @@ ti,no-reset-on-init; }; +&mmc2 { + status = "okay"; + vmmc-supply = <&wl12xx_vmmc>; + ti,non-removable; + bus-width = <4>; + cap-power-off-card; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; +}; + &mcasp1 { pinctrl-names = "default"; pinctrl-0 = <&mcasp1_pins>; diff --git a/arch/arm/boot/dts/am33xx.dtsi b/arch/arm/boot/dts/am33xx.dtsi index 79087ccf64bc..9770e35f2536 100644 --- a/arch/arm/boot/dts/am33xx.dtsi +++ b/arch/arm/boot/dts/am33xx.dtsi @@ -58,6 +58,10 @@ 275000 1125000 >; voltage-tolerance = <2>; /* 2 percentage */ + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + clock-latency = <300000>; /* From omap-cpufreq driver */ }; }; @@ -318,6 +322,7 @@ compatible = "ti,omap4-hwspinlock"; reg = <0x480ca000 0x1000>; ti,hwmods = "spinlock"; + #hwlock-cells = <1>; }; wdt2: wdt@44e35000 { @@ -399,7 +404,7 @@ ti,timer-pwm; }; - rtc@44e3e000 { + rtc: rtc@44e3e000 { compatible = "ti,da830-rtc"; reg = <0x44e3e000 0x1000>; interrupts = <75 @@ -582,6 +587,8 @@ compatible = "ti,am33xx-ecap"; #pwm-cells = <3>; reg = <0x48300100 0x80>; + interrupts = <31>; + interrupt-names = "ecap0"; ti,hwmods = "ecap0"; status = "disabled"; }; @@ -610,6 +617,8 @@ compatible = "ti,am33xx-ecap"; #pwm-cells = <3>; reg = <0x48302100 0x80>; + interrupts = <47>; + interrupt-names = "ecap1"; ti,hwmods = "ecap1"; status = "disabled"; }; @@ -638,6 +647,8 @@ compatible = "ti,am33xx-ecap"; #pwm-cells = <3>; reg = <0x48304100 0x80>; + interrupts = <61>; + interrupt-names = "ecap2"; ti,hwmods = "ecap2"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/am3517-craneboard.dts b/arch/arm/boot/dts/am3517-craneboard.dts new file mode 100644 index 000000000000..2d40b3f241cd --- /dev/null +++ b/arch/arm/boot/dts/am3517-craneboard.dts @@ -0,0 +1,174 @@ +/* + * See craneboard.org for more details + * + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "am3517.dtsi" + +/ { + model = "TI AM3517 CraneBoard (TMDSEVM3517)"; + compatible = "ti,am3517-craneboard", "ti,am3517", "ti,omap3"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + vbat: fixedregulator@0 { + compatible = "regulator-fixed"; + regulator-name = "vbat"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-boot-on; + }; +}; + +&davinci_emac { + status = "okay"; +}; + +&davinci_mdio { + status = "okay"; +}; + +&i2c1 { + clock-frequency = <2600000>; + + tps: tps@2d { + reg = <0x2d>; + }; +}; + +&i2c2 { + clock-frequency = <400000>; + /* goes to expansion connector */ + status = "disabled"; +}; + +&i2c3 { + clock-frequency = <400000>; + /* goes to expansion connector */ + status = "disabled"; +}; + +&mmc1 { + vmmc-supply = <&vdd2_reg>; + bus-width = <8>; +}; + +&mmc2 { + /* goes to expansion connector */ + status = "disabled"; +}; + +&mmc3 { + /* goes to expansion connector */ + status = "disabled"; +}; + +#include "tps65910.dtsi" + +&omap3_pmx_core { + tps_pins: pinmux_tps_pins { + pinctrl-single,pins = < + 0x1b0 (PIN_INPUT_PULLUP | MUX_MODE0) /* sys_nirq.sys_nirq */ + >; + }; +}; + +&tps { + pinctrl-names = "default"; + pinctrl-0 = <&tps_pins>; + + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + ti,en-ck32k-xtal; + + vcc1-supply = <&vbat>; + vcc2-supply = <&vbat>; + vcc3-supply = <&vbat>; + vcc4-supply = <&vbat>; + vcc5-supply = <&vbat>; + vcc6-supply = <&vbat>; + vcc7-supply = <&vbat>; + vccio-supply = <&vbat>; + + regulators { + vrtc_reg: regulator@0 { + regulator-always-on; + }; + + vio_reg: regulator@1 { + regulator-always-on; + }; + + /* + * Unused: + * VDIG1=2.7V,300mA max + * VDIG2=1.8V,300mA max + */ + + vpll_reg: regulator@7 { + /* VDDS_DPLL_1V8 */ + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vaux1_reg: regulator@9 { + /* VDDS_SRAM_1V8 */ + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vaux2_reg: regulator@10 { + /* VDDA1P8V_USBPHY */ + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + /* VAUX33 unused */ + + vdac_reg: regulator@8 { + /* VDDA_DAC_1V8 */ + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + vmmc_reg: regulator@12 { + /* VDDA3P3V_USBPHY */ + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vdd1_reg: regulator@2 { + /* VDD_CORE */ + regulator-name = "vdd_core"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-boot-on; + regulator-always-on; + }; + + vdd2_reg: regulator@3 { + /* VDDSHV_3V3 */ + regulator-name = "vdd_shv"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + /* VDD3 unused */ + }; +}; diff --git a/arch/arm/boot/dts/am4372.dtsi b/arch/arm/boot/dts/am4372.dtsi index c6bd4d986c29..36d523a26831 100644 --- a/arch/arm/boot/dts/am4372.dtsi +++ b/arch/arm/boot/dts/am4372.dtsi @@ -8,6 +8,7 @@ * kind, whether express or implied. */ +#include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include "skeleton.dtsi" @@ -33,6 +34,11 @@ compatible = "arm,cortex-a9"; device_type = "cpu"; reg = <0>; + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ }; }; @@ -351,6 +357,13 @@ status = "disabled"; }; + hwspinlock: spinlock@480ca000 { + compatible = "ti,omap4-hwspinlock"; + reg = <0x480ca000 0x1000>; + ti,hwmods = "spinlock"; + #hwlock-cells = <1>; + }; + i2c0: i2c@44e0b000 { compatible = "ti,am4372-i2c","ti,omap4-i2c"; reg = <0x44e0b000 0x1000>; @@ -521,6 +534,7 @@ ecap0: ecap@48300100 { compatible = "ti,am4372-ecap","ti,am33xx-ecap"; + #pwm-cells = <3>; reg = <0x48300100 0x80>; ti,hwmods = "ecap0"; status = "disabled"; @@ -528,6 +542,7 @@ ehrpwm0: ehrpwm@48300200 { compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + #pwm-cells = <3>; reg = <0x48300200 0x80>; ti,hwmods = "ehrpwm0"; status = "disabled"; @@ -545,6 +560,7 @@ ecap1: ecap@48302100 { compatible = "ti,am4372-ecap","ti,am33xx-ecap"; + #pwm-cells = <3>; reg = <0x48302100 0x80>; ti,hwmods = "ecap1"; status = "disabled"; @@ -552,6 +568,7 @@ ehrpwm1: ehrpwm@48302200 { compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + #pwm-cells = <3>; reg = <0x48302200 0x80>; ti,hwmods = "ehrpwm1"; status = "disabled"; @@ -569,6 +586,7 @@ ecap2: ecap@48304100 { compatible = "ti,am4372-ecap","ti,am33xx-ecap"; + #pwm-cells = <3>; reg = <0x48304100 0x80>; ti,hwmods = "ecap2"; status = "disabled"; @@ -576,6 +594,7 @@ ehrpwm2: ehrpwm@48304200 { compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + #pwm-cells = <3>; reg = <0x48304200 0x80>; ti,hwmods = "ehrpwm2"; status = "disabled"; @@ -593,6 +612,7 @@ ehrpwm3: ehrpwm@48306200 { compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + #pwm-cells = <3>; reg = <0x48306200 0x80>; ti,hwmods = "ehrpwm3"; status = "disabled"; @@ -610,6 +630,7 @@ ehrpwm4: ehrpwm@48308200 { compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + #pwm-cells = <3>; reg = <0x48308200 0x80>; ti,hwmods = "ehrpwm4"; status = "disabled"; @@ -627,6 +648,7 @@ ehrpwm5: ehrpwm@4830a200 { compatible = "ti,am4372-ehrpwm","ti,am33xx-ehrpwm"; + #pwm-cells = <3>; reg = <0x4830a200 0x80>; ti,hwmods = "ehrpwm5"; status = "disabled"; @@ -689,6 +711,30 @@ <&edma 11>; dma-names = "tx", "rx"; }; + + elm: elm@48080000 { + compatible = "ti,am3352-elm"; + reg = <0x48080000 0x2000>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "elm"; + clocks = <&l4ls_gclk>; + clock-names = "fck"; + status = "disabled"; + }; + + gpmc: gpmc@50000000 { + compatible = "ti,am3352-gpmc"; + ti,hwmods = "gpmc"; + clocks = <&l3s_gclk>; + clock-names = "fck"; + reg = <0x50000000 0x2000>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + gpmc,num-cs = <7>; + gpmc,num-waitpins = <2>; + #address-cells = <2>; + #size-cells = <1>; + status = "disabled"; + }; }; }; diff --git a/arch/arm/boot/dts/am437x-gp-evm.dts b/arch/arm/boot/dts/am437x-gp-evm.dts new file mode 100644 index 000000000000..df8798e8bd25 --- /dev/null +++ b/arch/arm/boot/dts/am437x-gp-evm.dts @@ -0,0 +1,127 @@ +/* + * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/ + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* AM437x GP EVM */ + +/dts-v1/; + +#include "am4372.dtsi" +#include <dt-bindings/pinctrl/am43xx.h> +#include <dt-bindings/pwm/pwm.h> +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "TI AM437x GP EVM"; + compatible = "ti,am437x-gp-evm","ti,am4372","ti,am43"; + + vmmcsd_fixed: fixedregulator-sd { + compatible = "regulator-fixed"; + regulator-name = "vmmcsd_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <0 51 53 56 62 75 101 152 255>; + default-brightness-level = <8>; + }; + + matrix_keypad: matrix_keypad@0 { + compatible = "gpio-matrix-keypad"; + debounce-delay-ms = <5>; + col-scan-delay-us = <2>; + + row-gpios = <&gpio3 21 GPIO_ACTIVE_HIGH /* Bank3, pin21 */ + &gpio4 3 GPIO_ACTIVE_HIGH /* Bank4, pin3 */ + &gpio4 2 GPIO_ACTIVE_HIGH>; /* Bank4, pin2 */ + + col-gpios = <&gpio3 19 GPIO_ACTIVE_HIGH /* Bank3, pin19 */ + &gpio3 20 GPIO_ACTIVE_HIGH>; /* Bank3, pin20 */ + + linux,keymap = <0x00000201 /* P1 */ + 0x00010202 /* P2 */ + 0x01000067 /* UP */ + 0x0101006a /* RIGHT */ + 0x02000069 /* LEFT */ + 0x0201006c>; /* DOWN */ + }; +}; + +&am43xx_pinmux { + i2c0_pins: i2c0_pins { + pinctrl-single,pins = < + 0x188 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_sda.i2c0_sda */ + 0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ + >; + }; + + i2c1_pins: i2c1_pins { + pinctrl-single,pins = < + 0x15c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2) /* spi0_cs0.i2c1_scl */ + 0x158 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE2) /* spi0_d1.i2c1_sda */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + >; + }; + + ecap0_pins: backlight_pins { + pinctrl-single,pins = < + 0x164 MUX_MODE0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ + >; + }; +}; + +&i2c0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins>; +}; + +&i2c1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; +}; + +&epwmss0 { + status = "okay"; +}; + +&ecap0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&ecap0_pins>; +}; + +&gpio0 { + status = "okay"; +}; + +&gpio3 { + status = "okay"; +}; + +&gpio4 { + status = "okay"; +}; + +&mmc1 { + status = "okay"; + vmmc-supply = <&vmmcsd_fixed>; + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; +}; diff --git a/arch/arm/boot/dts/am43x-epos-evm.dts b/arch/arm/boot/dts/am43x-epos-evm.dts index fbf9c4c7a94f..167dbc8494de 100644 --- a/arch/arm/boot/dts/am43x-epos-evm.dts +++ b/arch/arm/boot/dts/am43x-epos-evm.dts @@ -13,6 +13,7 @@ #include "am4372.dtsi" #include <dt-bindings/pinctrl/am43xx.h> #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pwm/pwm.h> / { model = "TI AM43x EPOS EVM"; @@ -79,6 +80,64 @@ 0x18c (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE0) /* i2c0_scl.i2c0_scl */ >; }; + + nand_flash_x8: nand_flash_x8 { + pinctrl-single,pins = < + 0x40 (PIN_OUTPUT_PULLDOWN | MUX_MODE7) /* gpmc_a0.SELQSPIorNAND/GPIO */ + 0x0 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad0.gpmc_ad0 */ + 0x4 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad1.gpmc_ad1 */ + 0x8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad2.gpmc_ad2 */ + 0xc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad3.gpmc_ad3 */ + 0x10 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad4.gpmc_ad4 */ + 0x14 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad5.gpmc_ad5 */ + 0x18 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad6.gpmc_ad6 */ + 0x1c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* gpmc_ad7.gpmc_ad7 */ + 0x70 (PIN_INPUT_PULLUP | MUX_MODE0) /* gpmc_wait0.gpmc_wait0 */ + 0x74 (PIN_OUTPUT_PULLUP | MUX_MODE7) /* gpmc_wpn.gpmc_wpn */ + 0x7c (PIN_OUTPUT | MUX_MODE0) /* gpmc_csn0.gpmc_csn0 */ + 0x90 (PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale.gpmc_advn_ale */ + 0x94 (PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren.gpmc_oen_ren */ + 0x98 (PIN_OUTPUT | MUX_MODE0) /* gpmc_wen.gpmc_wen */ + 0x9c (PIN_OUTPUT | MUX_MODE0) /* gpmc_be0n_cle.gpmc_be0n_cle */ + >; + }; + + ecap0_pins: backlight_pins { + pinctrl-single,pins = < + 0x164 MUX_MODE0 /* eCAP0_in_PWM0_out.eCAP0_in_PWM0_out MODE0 */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + 0x1c0 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8) /* i2c2_sda.i2c2_sda */ + 0x1c4 (PIN_INPUT_PULLUP | SLEWCTRL_FAST | MUX_MODE8) /* i2c2_scl.i2c2_scl */ + >; + }; + + spi0_pins: pinmux_spi0_pins { + pinctrl-single,pins = < + 0x150 (PIN_INPUT | MUX_MODE0) /* spi0_clk.spi0_clk */ + 0x154 (PIN_OUTPUT | MUX_MODE0) /* spi0_d0.spi0_d0 */ + 0x158 (PIN_INPUT | MUX_MODE0) /* spi0_d1.spi0_d1 */ + 0x15c (PIN_OUTPUT | MUX_MODE0) /* spi0_cs0.spi0_cs0 */ + >; + }; + + spi1_pins: pinmux_spi1_pins { + pinctrl-single,pins = < + 0x190 (PIN_INPUT | MUX_MODE3) /* mcasp0_aclkx.spi1_clk */ + 0x194 (PIN_OUTPUT | MUX_MODE3) /* mcasp0_fsx.spi1_d0 */ + 0x198 (PIN_INPUT | MUX_MODE3) /* mcasp0_axr0.spi1_d1 */ + 0x19c (PIN_OUTPUT | MUX_MODE3) /* mcasp0_ahclkr.spi1_cs0 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0x160 (PIN_INPUT | MUX_MODE7) /* spi0_cs1.gpio0_6 */ + >; + }; }; matrix_keypad: matrix_keypad@0 { @@ -113,12 +172,22 @@ 0x0203006c /* DOWN */ 0x03030069>; /* LEFT */ }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&ecap0 0 50000 PWM_POLARITY_INVERTED>; + brightness-levels = <0 51 53 56 62 75 101 152 255>; + default-brightness-level = <8>; + }; }; &mmc1 { status = "okay"; vmmc-supply = <&vmmcsd_fixed>; bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + cd-gpios = <&gpio0 6 GPIO_ACTIVE_HIGH>; }; &mac { @@ -169,6 +238,12 @@ }; }; +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + status = "okay"; +}; + &gpio0 { status = "okay"; }; @@ -184,3 +259,111 @@ &gpio3 { status = "okay"; }; + +&elm { + status = "okay"; +}; + +&gpmc { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&nand_flash_x8>; + ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */ + nand@0,0 { + reg = <0 0 0>; /* CS0, offset 0 */ + ti,nand-ecc-opt = "bch8"; + ti,elm-id = <&elm>; + nand-bus-width = <8>; + gpmc,device-width = <1>; + gpmc,sync-clk-ps = <0>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <40>; /* tCEA + tCHZ + 1 */ + gpmc,cs-wr-off-ns = <40>; + gpmc,adv-on-ns = <0>; /* cs-on-ns */ + gpmc,adv-rd-off-ns = <25>; /* min( tALH + tALS + 1) */ + gpmc,adv-wr-off-ns = <25>; /* min( tALH + tALS + 1) */ + gpmc,we-on-ns = <0>; /* cs-on-ns */ + gpmc,we-off-ns = <20>; /* we-on-time + tWP + 2 */ + gpmc,oe-on-ns = <3>; /* cs-on-ns + tRR + 2 */ + gpmc,oe-off-ns = <30>; /* oe-on-ns + tRP + 2 */ + gpmc,access-ns = <30>; /* tCEA + 4*/ + gpmc,rd-cycle-ns = <40>; + gpmc,wr-cycle-ns = <40>; + gpmc,wait-on-read = "true"; + gpmc,wait-on-write = "true"; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,clk-activation-ns = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,wr-access-ns = <40>; + gpmc,wr-data-mux-bus-ns = <0>; + /* MTD partition table */ + /* All SPL-* partitions are sized to minimal length + * which can be independently programmable. For + * NAND flash this is equal to size of erase-block */ + #address-cells = <1>; + #size-cells = <1>; + partition@0 { + label = "NAND.SPL"; + reg = <0x00000000 0x00040000>; + }; + partition@1 { + label = "NAND.SPL.backup1"; + reg = <0x00040000 0x00040000>; + }; + partition@2 { + label = "NAND.SPL.backup2"; + reg = <0x00080000 0x00040000>; + }; + partition@3 { + label = "NAND.SPL.backup3"; + reg = <0x000C0000 0x00040000>; + }; + partition@4 { + label = "NAND.u-boot-spl-os"; + reg = <0x00100000 0x00080000>; + }; + partition@5 { + label = "NAND.u-boot"; + reg = <0x00180000 0x00100000>; + }; + partition@6 { + label = "NAND.u-boot-env"; + reg = <0x00280000 0x00040000>; + }; + partition@7 { + label = "NAND.u-boot-env.backup1"; + reg = <0x002C0000 0x00040000>; + }; + partition@8 { + label = "NAND.kernel"; + reg = <0x00300000 0x00700000>; + }; + partition@9 { + label = "NAND.file-system"; + reg = <0x00800000 0x1F600000>; + }; + }; +}; + +&epwmss0 { + status = "okay"; +}; + +&ecap0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&ecap0_pins>; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi0_pins>; + status = "okay"; +}; + +&spi1 { + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/armada-370-db.dts b/arch/arm/boot/dts/armada-370-db.dts index 08a56bcfc724..82f238a9063f 100644 --- a/arch/arm/boot/dts/armada-370-db.dts +++ b/arch/arm/boot/dts/armada-370-db.dts @@ -64,6 +64,22 @@ phy-mode = "rgmii-id"; }; + i2c@11000 { + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + status = "okay"; + audio_codec: audio-codec@4a { + compatible = "cirrus,cs42l51"; + reg = <0x4a>; + }; + }; + + audio-controller@30000 { + pinctrl-0 = <&i2s_pins2>; + pinctrl-names = "default"; + status = "okay"; + }; + mvsdio@d4000 { pinctrl-0 = <&sdio_pins1>; pinctrl-names = "default"; @@ -80,6 +96,30 @@ broken-cd; }; + pinctrl { + /* + * These pins might be muxed as I2S by + * the bootloader, but it conflicts + * with the real I2S pins that are + * muxed using i2s_pins. We must mux + * those pins to a function other than + * I2S. + */ + pinctrl-0 = <&hog_pins1 &hog_pins2>; + pinctrl-names = "default"; + + hog_pins1: hog-pins1 { + marvell,pins = "mpp6", "mpp8", "mpp10", + "mpp12", "mpp13"; + marvell,function = "gpio"; + }; + + hog_pins2: hog-pins2 { + marvell,pins = "mpp5", "mpp7", "mpp9"; + marvell,function = "gpo"; + }; + }; + usb@50000 { status = "okay"; }; @@ -112,10 +152,26 @@ /* Port 0, Lane 0 */ status = "okay"; }; + pcie@2,0 { /* Port 1, Lane 0 */ status = "okay"; }; }; }; + + sound { + compatible = "marvell,a370db-audio"; + marvell,audio-controller = <&audio_controller>; + marvell,audio-codec = <&audio_codec &spdif_out &spdif_in>; + status = "okay"; + }; + + spdif_out: spdif-out { + compatible = "linux,spdif-dit"; + }; + + spdif_in: spdif-in { + compatible = "linux,spdif-dir"; + }; }; diff --git a/arch/arm/boot/dts/armada-370-mirabox.dts b/arch/arm/boot/dts/armada-370-mirabox.dts index 944e8785b308..2354fe023ee0 100644 --- a/arch/arm/boot/dts/armada-370-mirabox.dts +++ b/arch/arm/boot/dts/armada-370-mirabox.dts @@ -9,6 +9,7 @@ */ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> #include "armada-370.dtsi" / { @@ -73,19 +74,19 @@ green_pwr_led { label = "mirabox:green:pwr"; - gpios = <&gpio1 31 1>; + gpios = <&gpio1 31 GPIO_ACTIVE_LOW>; default-state = "keep"; }; blue_stat_led { label = "mirabox:blue:stat"; - gpios = <&gpio2 0 1>; + gpios = <&gpio2 0 GPIO_ACTIVE_LOW>; default-state = "off"; }; green_stat_led { label = "mirabox:green:stat"; - gpios = <&gpio2 1 1>; + gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; default-state = "off"; }; }; diff --git a/arch/arm/boot/dts/armada-370-rd.dts b/arch/arm/boot/dts/armada-370-rd.dts index abbb807459d2..3e2c857d6000 100644 --- a/arch/arm/boot/dts/armada-370-rd.dts +++ b/arch/arm/boot/dts/armada-370-rd.dts @@ -12,6 +12,8 @@ */ /dts-v1/; +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> #include "armada-370.dtsi" / { @@ -100,8 +102,8 @@ #size-cells = <0>; button@1 { label = "Software Button"; - linux,code = <116>; - gpios = <&gpio0 6 1>; + linux,code = <KEY_POWER>; + gpios = <&gpio0 6 GPIO_ACTIVE_LOW>; }; }; diff --git a/arch/arm/boot/dts/armada-370-xp.dtsi b/arch/arm/boot/dts/armada-370-xp.dtsi index 74b5964430ac..bbb40f62037d 100644 --- a/arch/arm/boot/dts/armada-370-xp.dtsi +++ b/arch/arm/boot/dts/armada-370-xp.dtsi @@ -44,8 +44,8 @@ #size-cells = <1>; controller = <&mbusc>; interrupt-parent = <&mpic>; - pcie-mem-aperture = <0xe0000000 0x8000000>; - pcie-io-aperture = <0xe8000000 0x100000>; + pcie-mem-aperture = <0xf8000000 0x7e00000>; + pcie-io-aperture = <0xffe00000 0x100000>; devbus-bootcs { compatible = "marvell,mvebu-devbus"; @@ -199,6 +199,10 @@ interrupts = <37>, <38>, <39>, <40>, <5>, <6>; }; + watchdog@20300 { + reg = <0x20300 0x34>, <0x20704 0x4>; + }; + usb@50000 { compatible = "marvell,orion-ehci"; reg = <0x50000 0x500>; diff --git a/arch/arm/boot/dts/armada-370.dtsi b/arch/arm/boot/dts/armada-370.dtsi index 0d8530c98cf5..af1f11e9e5a0 100644 --- a/arch/arm/boot/dts/armada-370.dtsi +++ b/arch/arm/boot/dts/armada-370.dtsi @@ -132,6 +132,25 @@ "mpp51", "mpp52", "mpp53"; marvell,function = "sd0"; }; + + i2c0_pins: i2c0-pins { + marvell,pins = "mpp2", "mpp3"; + marvell,function = "i2c0"; + }; + + i2s_pins1: i2s-pins1 { + marvell,pins = "mpp5", "mpp6", "mpp7", + "mpp8", "mpp9", "mpp10", + "mpp12", "mpp13"; + marvell,function = "audio"; + }; + + i2s_pins2: i2s-pins2 { + marvell,pins = "mpp49", "mpp47", "mpp50", + "mpp59", "mpp57", "mpp61", + "mpp62", "mpp60", "mpp58"; + marvell,function = "audio"; + }; }; gpio0: gpio@18100 { @@ -196,6 +215,20 @@ clocks = <&coreclk 2>; }; + watchdog@20300 { + compatible = "marvell,armada-370-wdt"; + clocks = <&coreclk 2>; + }; + + audio_controller: audio-controller@30000 { + compatible = "marvell,armada370-audio"; + reg = <0x30000 0x4000>; + interrupts = <93>; + clocks = <&gateclk 0>; + clock-names = "internal"; + status = "disabled"; + }; + usb@50000 { clocks = <&coreclk 0>; }; diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts new file mode 100644 index 000000000000..9378d3136b41 --- /dev/null +++ b/arch/arm/boot/dts/armada-375-db.dts @@ -0,0 +1,130 @@ +/* + * Device Tree file for Marvell Armada 375 evaluation board + * (DB-88F6720) + * + * Copyright (C) 2014 Marvell + * + * Gregory CLEMENT <gregory.clement@free-electrons.com> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include "armada-375.dtsi" + +/ { + model = "Marvell Armada 375 Development Board"; + compatible = "marvell,a375-db", "marvell,armada375"; + + chosen { + bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x40000000>; /* 1 GB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; + + internal-regs { + spi@10600 { + pinctrl-0 = <&spi0_pins>; + pinctrl-names = "default"; + /* + * SPI conflicts with NAND, so we disable it + * here, and select NAND as the enabled device + * by default. + */ + status = "disabled"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "n25q128a13"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <108000000>; + }; + }; + + i2c@11000 { + status = "okay"; + clock-frequency = <100000>; + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + }; + + i2c@11100 { + status = "okay"; + clock-frequency = <100000>; + pinctrl-0 = <&i2c1_pins>; + pinctrl-names = "default"; + }; + + serial@12000 { + clock-frequency = <200000000>; + status = "okay"; + }; + + pinctrl { + sdio_st_pins: sdio-st-pins { + marvell,pins = "mpp44", "mpp45"; + marvell,function = "gpio"; + }; + }; + + nand: nand@d0000 { + pinctrl-0 = <&nand_pins>; + pinctrl-names = "default"; + status = "okay"; + num-cs = <1>; + marvell,nand-keep-config; + marvell,nand-enable-arbiter; + nand-on-flash-bbt; + + partition@0 { + label = "U-Boot"; + reg = <0 0x800000>; + }; + partition@800000 { + label = "Linux"; + reg = <0x800000 0x800000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; + }; + + mvsdio@d4000 { + pinctrl-0 = <&sdio_pins &sdio_st_pins>; + pinctrl-names = "default"; + status = "okay"; + cd-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>; + wp-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + }; + + pcie-controller { + status = "okay"; + /* + * The two PCIe units are accessible through + * standard PCIe slots on the board. + */ + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + pcie@2,0 { + /* Port 1, Lane 0 */ + status = "okay"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-375.dtsi b/arch/arm/boot/dts/armada-375.dtsi new file mode 100644 index 000000000000..3877693fb2d8 --- /dev/null +++ b/arch/arm/boot/dts/armada-375.dtsi @@ -0,0 +1,464 @@ +/* + * Device Tree Include file for Marvell Armada 375 family SoC + * + * Copyright (C) 2014 Marvell + * + * Gregory CLEMENT <gregory.clement@free-electrons.com> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include "skeleton.dtsi" +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/interrupt-controller/irq.h> + +#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) + +/ { + model = "Marvell Armada 375 family SoC"; + compatible = "marvell,armada375"; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + gpio2 = &gpio2; + }; + + clocks { + /* 2 GHz fixed main PLL */ + mainpll: mainpll { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <2000000000>; + }; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <0>; + }; + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <1>; + }; + }; + + soc { + compatible = "marvell,armada375-mbus", "marvell,armada370-mbus", "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + controller = <&mbusc>; + interrupt-parent = <&gic>; + pcie-mem-aperture = <0xe0000000 0x8000000>; + pcie-io-aperture = <0xe8000000 0x100000>; + + bootrom { + compatible = "marvell,bootrom"; + reg = <MBUS_ID(0x01, 0x1d) 0 0x100000>; + }; + + devbus-bootcs { + compatible = "marvell,mvebu-devbus"; + reg = <MBUS_ID(0xf0, 0x01) 0x10400 0x8>; + ranges = <0 MBUS_ID(0x01, 0x2f) 0 0xffffffff>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + devbus-cs0 { + compatible = "marvell,mvebu-devbus"; + reg = <MBUS_ID(0xf0, 0x01) 0x10408 0x8>; + ranges = <0 MBUS_ID(0x01, 0x3e) 0 0xffffffff>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + devbus-cs1 { + compatible = "marvell,mvebu-devbus"; + reg = <MBUS_ID(0xf0, 0x01) 0x10410 0x8>; + ranges = <0 MBUS_ID(0x01, 0x3d) 0 0xffffffff>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + devbus-cs2 { + compatible = "marvell,mvebu-devbus"; + reg = <MBUS_ID(0xf0, 0x01) 0x10418 0x8>; + ranges = <0 MBUS_ID(0x01, 0x3b) 0 0xffffffff>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + devbus-cs3 { + compatible = "marvell,mvebu-devbus"; + reg = <MBUS_ID(0xf0, 0x01) 0x10420 0x8>; + ranges = <0 MBUS_ID(0x01, 0x37) 0 0xffffffff>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + internal-regs { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>; + + L2: cache-controller@8000 { + compatible = "arm,pl310-cache"; + reg = <0x8000 0x1000>; + cache-unified; + cache-level = <2>; + }; + + timer@c600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0xc600 0x20>; + interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>; + clocks = <&coreclk 2>; + }; + + gic: interrupt-controller@d000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #size-cells = <0>; + interrupt-controller; + reg = <0xd000 0x1000>, + <0xc100 0x100>; + }; + + spi0: spi@10600 { + compatible = "marvell,orion-spi"; + reg = <0x10600 0x50>; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + spi1: spi@10680 { + compatible = "marvell,orion-spi"; + reg = <0x10680 0x50>; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <1>; + interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c0: i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c1: i2c@11100 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11100 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + serial@12000 { + compatible = "snps,dw-apb-uart"; + reg = <0x12000 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + status = "disabled"; + }; + + serial@12100 { + compatible = "snps,dw-apb-uart"; + reg = <0x12100 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + status = "disabled"; + }; + + pinctrl { + compatible = "marvell,mv88f6720-pinctrl"; + reg = <0x18000 0x24>; + + i2c0_pins: i2c0-pins { + marvell,pins = "mpp14", "mpp15"; + marvell,function = "i2c0"; + }; + + i2c1_pins: i2c1-pins { + marvell,pins = "mpp61", "mpp62"; + marvell,function = "i2c1"; + }; + + nand_pins: nand-pins { + marvell,pins = "mpp0", "mpp1", "mpp2", + "mpp3", "mpp4", "mpp5", + "mpp6", "mpp7", "mpp8", + "mpp9", "mpp10", "mpp11", + "mpp12", "mpp13"; + marvell,function = "nand"; + }; + + sdio_pins: sdio-pins { + marvell,pins = "mpp24", "mpp25", "mpp26", + "mpp27", "mpp28", "mpp29"; + marvell,function = "sd"; + }; + + spi0_pins: spi0-pins { + marvell,pins = "mpp0", "mpp1", "mpp4", + "mpp5", "mpp8", "mpp9"; + marvell,function = "spi0"; + }; + }; + + gpio0: gpio@18100 { + compatible = "marvell,orion-gpio"; + reg = <0x18100 0x40>; + ngpios = <32>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpio1: gpio@18140 { + compatible = "marvell,orion-gpio"; + reg = <0x18140 0x40>; + ngpios = <32>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpio2: gpio@18180 { + compatible = "marvell,orion-gpio"; + reg = <0x18180 0x40>; + ngpios = <3>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; + }; + + system-controller@18200 { + compatible = "marvell,armada-375-system-controller"; + reg = <0x18200 0x100>; + }; + + gateclk: clock-gating-control@18220 { + compatible = "marvell,armada-375-gating-clock"; + reg = <0x18220 0x4>; + clocks = <&coreclk 0>; + #clock-cells = <1>; + }; + + mbusc: mbus-controller@20000 { + compatible = "marvell,mbus-controller"; + reg = <0x20000 0x100>, <0x20180 0x20>; + }; + + mpic: interrupt-controller@20000 { + compatible = "marvell,mpic"; + reg = <0x20a00 0x2d0>, <0x21070 0x58>; + #interrupt-cells = <1>; + #size-cells = <1>; + interrupt-controller; + msi-controller; + interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer@20300 { + compatible = "marvell,armada-375-timer", "marvell,armada-370-timer"; + reg = <0x20300 0x30>, <0x21040 0x30>; + interrupts-extended = <&gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, + <&mpic 5>, + <&mpic 6>; + clocks = <&coreclk 0>; + }; + + xor@60800 { + compatible = "marvell,orion-xor"; + reg = <0x60800 0x100 + 0x60A00 0x100>; + clocks = <&gateclk 22>; + status = "okay"; + + xor00 { + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + dmacap,memcpy; + dmacap,xor; + }; + xor01 { + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; + dmacap,memcpy; + dmacap,xor; + dmacap,memset; + }; + }; + + xor@60900 { + compatible = "marvell,orion-xor"; + reg = <0x60900 0x100 + 0x60b00 0x100>; + clocks = <&gateclk 23>; + status = "okay"; + + xor10 { + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + dmacap,memcpy; + dmacap,xor; + }; + xor11 { + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; + dmacap,memcpy; + dmacap,xor; + dmacap,memset; + }; + }; + + sata@a0000 { + compatible = "marvell,orion-sata"; + reg = <0xa0000 0x5000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gateclk 14>, <&gateclk 20>; + clock-names = "0", "1"; + status = "disabled"; + }; + + nand@d0000 { + compatible = "marvell,armada370-nand"; + reg = <0xd0000 0x54>; + #address-cells = <1>; + #size-cells = <1>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gateclk 11>; + status = "disabled"; + }; + + mvsdio@d4000 { + compatible = "marvell,orion-sdio"; + reg = <0xd4000 0x200>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&gateclk 17>; + bus-width = <4>; + cap-sdio-irq; + cap-sd-highspeed; + cap-mmc-highspeed; + status = "disabled"; + }; + + coreclk: mvebu-sar@e8204 { + compatible = "marvell,armada-375-core-clock"; + reg = <0xe8204 0x04>; + #clock-cells = <1>; + }; + + coredivclk: corediv-clock@e8250 { + compatible = "marvell,armada-375-corediv-clock"; + reg = <0xe8250 0xc>; + #clock-cells = <1>; + clocks = <&mainpll>; + clock-output-names = "nand"; + }; + }; + + pcie-controller { + compatible = "marvell,armada-370-pcie"; + status = "disabled"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + msi-parent = <&mpic>; + bus-range = <0x00 0xff>; + + ranges = + <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 + 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 + 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0 MEM */ + 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0 IO */ + 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 1 MEM */ + 0x81000000 0x2 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 1 IO */>; + + pcie@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 + 0x81000000 0 0 0x81000000 0x1 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 5>; + status = "disabled"; + }; + + pcie@2,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x44000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 + 0x81000000 0 0 0x81000000 0x2 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <1>; + clocks = <&gateclk 6>; + status = "disabled"; + }; + + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-380.dtsi b/arch/arm/boot/dts/armada-380.dtsi new file mode 100644 index 000000000000..068031f0f263 --- /dev/null +++ b/arch/arm/boot/dts/armada-380.dtsi @@ -0,0 +1,117 @@ +/* + * Device Tree Include file for Marvell Armada 380 SoC. + * + * Copyright (C) 2014 Marvell + * + * Lior Amsalem <alior@marvell.com> + * Gregory CLEMENT <gregory.clement@free-electrons.com> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include "armada-38x.dtsi" + +/ { + model = "Marvell Armada 380 family SoC"; + compatible = "marvell,armada380", "marvell,armada38x"; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <0>; + }; + }; + + soc { + internal-regs { + pinctrl { + compatible = "marvell,mv88f6810-pinctrl"; + reg = <0x18000 0x20>; + }; + }; + + pcie-controller { + compatible = "marvell,armada-370-pcie"; + status = "disabled"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + msi-parent = <&mpic>; + bus-range = <0x00 0xff>; + + ranges = + <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 + 0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 + 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 + 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 + 0x82000000 0x1 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */ + 0x81000000 0x1 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO */ + 0x82000000 0x2 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */ + 0x81000000 0x2 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO */ + 0x82000000 0x3 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */ + 0x81000000 0x3 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO */>; + + /* x1 port */ + pcie@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x80000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 + 0x81000000 0 0 0x81000000 0x1 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 8>; + status = "disabled"; + }; + + /* x1 port */ + pcie@2,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 + 0x81000000 0 0 0x81000000 0x2 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 5>; + status = "disabled"; + }; + + /* x1 port */ + pcie@3,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x44000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0 + 0x81000000 0 0 0x81000000 0x3 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <2>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 6>; + status = "disabled"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-385-db.dts b/arch/arm/boot/dts/armada-385-db.dts new file mode 100644 index 000000000000..6828d77696a6 --- /dev/null +++ b/arch/arm/boot/dts/armada-385-db.dts @@ -0,0 +1,122 @@ +/* + * Device Tree file for Marvell Armada 385 evaluation board + * (DB-88F6820) + * + * Copyright (C) 2014 Marvell + * + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; +#include "armada-385.dtsi" + +/ { + model = "Marvell Armada 385 Development Board"; + compatible = "marvell,a385-db", "marvell,armada385", "marvell,armada38x"; + + chosen { + bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; /* 256 MB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; + + internal-regs { + spi@10600 { + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "w25q32"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <108000000>; + }; + }; + + i2c@11000 { + status = "okay"; + clock-frequency = <100000>; + }; + + i2c@11100 { + status = "okay"; + clock-frequency = <100000>; + }; + + serial@12000 { + clock-frequency = <200000000>; + status = "okay"; + }; + + ethernet@30000 { + status = "okay"; + phy = <&phy1>; + phy-mode = "rgmii-id"; + }; + + ethernet@70000 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; + + mdio { + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + + flash@d0000 { + status = "okay"; + num-cs = <1>; + marvell,nand-keep-config; + marvell,nand-enable-arbiter; + nand-on-flash-bbt; + + partition@0 { + label = "U-Boot"; + reg = <0 0x800000>; + }; + partition@800000 { + label = "Linux"; + reg = <0x800000 0x800000>; + }; + partition@1000000 { + label = "Filesystem"; + reg = <0x1000000 0x3f000000>; + }; + }; + }; + + pcie-controller { + status = "okay"; + /* + * The two PCIe units are accessible through + * standard PCIe slots on the board. + */ + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + pcie@2,0 { + /* Port 1, Lane 0 */ + status = "okay"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-385-rd.dts b/arch/arm/boot/dts/armada-385-rd.dts new file mode 100644 index 000000000000..45250c88814b --- /dev/null +++ b/arch/arm/boot/dts/armada-385-rd.dts @@ -0,0 +1,94 @@ +/* + * Device Tree file for Marvell Armada 385 Reference Design board + * (RD-88F6820-AP) + * + * Copyright (C) 2014 Marvell + * + * Gregory CLEMENT <gregory.clement@free-electrons.com> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; +#include "armada-385.dtsi" + +/ { + model = "Marvell Armada 385 Reference Design"; + compatible = "marvell,a385-rd", "marvell,armada385", "marvell,armada38x"; + + chosen { + bootargs = "console=ttyS0,115200 earlyprintk"; + }; + + memory { + device_type = "memory"; + reg = <0x00000000 0x10000000>; /* 256 MB */ + }; + + soc { + ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000 + MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000>; + + internal-regs { + spi@10600 { + status = "okay"; + + spi-flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p128"; + reg = <0>; /* Chip select 0 */ + spi-max-frequency = <108000000>; + }; + }; + + i2c@11000 { + status = "okay"; + clock-frequency = <100000>; + }; + + serial@12000 { + clock-frequency = <200000000>; + status = "okay"; + }; + + ethernet@30000 { + status = "okay"; + phy = <&phy0>; + phy-mode = "rgmii-id"; + }; + + ethernet@70000 { + status = "okay"; + phy = <&phy1>; + phy-mode = "rgmii-id"; + }; + + + mdio { + phy0: ethernet-phy@0 { + reg = <0>; + }; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + }; + + pcie-controller { + status = "okay"; + /* + * One PCIe units is accessible through + * standard PCIe slot on the board. + */ + pcie@1,0 { + /* Port 0, Lane 0 */ + status = "okay"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-385.dtsi b/arch/arm/boot/dts/armada-385.dtsi new file mode 100644 index 000000000000..e2919f02e1d4 --- /dev/null +++ b/arch/arm/boot/dts/armada-385.dtsi @@ -0,0 +1,149 @@ +/* + * Device Tree Include file for Marvell Armada 385 SoC. + * + * Copyright (C) 2014 Marvell + * + * Lior Amsalem <alior@marvell.com> + * Gregory CLEMENT <gregory.clement@free-electrons.com> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include "armada-38x.dtsi" + +/ { + model = "Marvell Armada 385 family SoC"; + compatible = "marvell,armada385", "marvell,armada38x"; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <0>; + }; + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + reg = <1>; + }; + }; + + soc { + internal-regs { + pinctrl { + compatible = "marvell,mv88f6820-pinctrl"; + reg = <0x18000 0x20>; + }; + }; + + pcie-controller { + compatible = "marvell,armada-370-pcie"; + status = "disabled"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + msi-parent = <&mpic>; + bus-range = <0x00 0xff>; + + ranges = + <0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 + 0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 + 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 + 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 + 0x82000000 0x1 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 0 MEM */ + 0x81000000 0x1 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 0 IO */ + 0x82000000 0x2 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 1 MEM */ + 0x81000000 0x2 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 1 IO */ + 0x82000000 0x3 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 2 MEM */ + 0x81000000 0x3 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 2 IO */ + 0x82000000 0x4 0 MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 3 MEM */ + 0x81000000 0x4 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 3 IO */>; + + /* + * This port can be either x4 or x1. When + * configured in x4 by the bootloader, then + * pcie@4,0 is not available. + */ + pcie@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x80000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 + 0x81000000 0 0 0x81000000 0x1 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 8>; + status = "disabled"; + }; + + /* x1 port */ + pcie@2,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 + 0x81000000 0 0 0x81000000 0x2 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 5>; + status = "disabled"; + }; + + /* x1 port */ + pcie@3,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x44000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0 + 0x81000000 0 0 0x81000000 0x3 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <2>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 6>; + status = "disabled"; + }; + + /* + * x1 port only available when pcie@1,0 is + * configured as a x1 port + */ + pcie@4,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x48000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0 + 0x81000000 0 0 0x81000000 0x4 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; + marvell,pcie-port = <3>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 7>; + status = "disabled"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi new file mode 100644 index 000000000000..a064f59da02d --- /dev/null +++ b/arch/arm/boot/dts/armada-38x.dtsi @@ -0,0 +1,376 @@ +/* + * Device Tree Include file for Marvell Armada 38x family of SoCs. + * + * Copyright (C) 2014 Marvell + * + * Lior Amsalem <alior@marvell.com> + * Gregory CLEMENT <gregory.clement@free-electrons.com> + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +#include "skeleton.dtsi" +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/interrupt-controller/irq.h> + +#define MBUS_ID(target,attributes) (((target) << 24) | ((attributes) << 16)) + +/ { + model = "Marvell Armada 38x family SoC"; + compatible = "marvell,armada38x"; + + aliases { + gpio0 = &gpio0; + gpio1 = &gpio1; + eth0 = ð0; + eth1 = ð1; + eth2 = ð2; + }; + + soc { + compatible = "marvell,armada380-mbus", "marvell,armada370-mbus", + "simple-bus"; + #address-cells = <2>; + #size-cells = <1>; + controller = <&mbusc>; + interrupt-parent = <&gic>; + pcie-mem-aperture = <0xe0000000 0x8000000>; + pcie-io-aperture = <0xe8000000 0x100000>; + + bootrom { + compatible = "marvell,bootrom"; + reg = <MBUS_ID(0x01, 0x1d) 0 0x200000>; + }; + + devbus-bootcs { + compatible = "marvell,mvebu-devbus"; + reg = <MBUS_ID(0xf0, 0x01) 0x10400 0x8>; + ranges = <0 MBUS_ID(0x01, 0x2f) 0 0xffffffff>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + devbus-cs0 { + compatible = "marvell,mvebu-devbus"; + reg = <MBUS_ID(0xf0, 0x01) 0x10408 0x8>; + ranges = <0 MBUS_ID(0x01, 0x3e) 0 0xffffffff>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + devbus-cs1 { + compatible = "marvell,mvebu-devbus"; + reg = <MBUS_ID(0xf0, 0x01) 0x10410 0x8>; + ranges = <0 MBUS_ID(0x01, 0x3d) 0 0xffffffff>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + devbus-cs2 { + compatible = "marvell,mvebu-devbus"; + reg = <MBUS_ID(0xf0, 0x01) 0x10418 0x8>; + ranges = <0 MBUS_ID(0x01, 0x3b) 0 0xffffffff>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + devbus-cs3 { + compatible = "marvell,mvebu-devbus"; + reg = <MBUS_ID(0xf0, 0x01) 0x10420 0x8>; + ranges = <0 MBUS_ID(0x01, 0x37) 0 0xffffffff>; + #address-cells = <1>; + #size-cells = <1>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + internal-regs { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 MBUS_ID(0xf0, 0x01) 0 0x100000>; + + L2: cache-controller@8000 { + compatible = "arm,pl310-cache"; + reg = <0x8000 0x1000>; + cache-unified; + cache-level = <2>; + }; + + timer@c600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0xc600 0x20>; + interrupts = <GIC_PPI 13 (IRQ_TYPE_EDGE_RISING | GIC_CPU_MASK_SIMPLE(2))>; + clocks = <&coreclk 2>; + }; + + gic: interrupt-controller@d000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #size-cells = <0>; + interrupt-controller; + reg = <0xd000 0x1000>, + <0xc100 0x100>; + }; + + spi0: spi@10600 { + compatible = "marvell,orion-spi"; + reg = <0x10600 0x50>; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <0>; + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + spi1: spi@10680 { + compatible = "marvell,orion-spi"; + reg = <0x10680 0x50>; + #address-cells = <1>; + #size-cells = <0>; + cell-index = <1>; + interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c0: i2c@11000 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11000 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + i2c1: i2c@11100 { + compatible = "marvell,mv64xxx-i2c"; + reg = <0x11100 0x20>; + #address-cells = <1>; + #size-cells = <0>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + timeout-ms = <1000>; + clocks = <&coreclk 0>; + status = "disabled"; + }; + + serial@12000 { + compatible = "snps,dw-apb-uart"; + reg = <0x12000 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + status = "disabled"; + }; + + serial@12100 { + compatible = "snps,dw-apb-uart"; + reg = <0x12100 0x100>; + reg-shift = <2>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; + reg-io-width = <1>; + status = "disabled"; + }; + + pinctrl { + compatible = "marvell,mv88f6820-pinctrl"; + reg = <0x18000 0x20>; + }; + + gpio0: gpio@18100 { + compatible = "marvell,orion-gpio"; + reg = <0x18100 0x40>; + ngpios = <32>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; + }; + + gpio1: gpio@18140 { + compatible = "marvell,orion-gpio"; + reg = <0x18140 0x40>; + ngpios = <28>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + interrupts = <GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; + }; + + system-controller@18200 { + compatible = "marvell,armada-380-system-controller", + "marvell,armada-370-xp-system-controller"; + reg = <0x18200 0x100>; + }; + + gateclk: clock-gating-control@18220 { + compatible = "marvell,armada-380-gating-clock"; + reg = <0x18220 0x4>; + clocks = <&coreclk 0>; + #clock-cells = <1>; + }; + + coreclk: mvebu-sar@18600 { + compatible = "marvell,armada-380-core-clock"; + reg = <0x18600 0x04>; + #clock-cells = <1>; + }; + + mbusc: mbus-controller@20000 { + compatible = "marvell,mbus-controller"; + reg = <0x20000 0x100>, <0x20180 0x20>; + }; + + mpic: interrupt-controller@20000 { + compatible = "marvell,mpic"; + reg = <0x20a00 0x2d0>, <0x21070 0x58>; + #interrupt-cells = <1>; + #size-cells = <1>; + interrupt-controller; + msi-controller; + interrupts = <GIC_PPI 15 IRQ_TYPE_LEVEL_HIGH>; + }; + + timer@20300 { + compatible = "marvell,armada-380-timer", + "marvell,armada-xp-timer"; + reg = <0x20300 0x30>, <0x21040 0x30>; + interrupts-extended = <&gic GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, + <&gic GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, + <&mpic 5>, + <&mpic 6>; + clocks = <&coreclk 2>, <&refclk>; + clock-names = "nbclk", "fixed"; + }; + + eth1: ethernet@30000 { + compatible = "marvell,armada-370-neta"; + reg = <0x30000 0x4000>; + interrupts-extended = <&mpic 10>; + clocks = <&gateclk 3>; + status = "disabled"; + }; + + eth2: ethernet@34000 { + compatible = "marvell,armada-370-neta"; + reg = <0x34000 0x4000>; + interrupts-extended = <&mpic 12>; + clocks = <&gateclk 2>; + status = "disabled"; + }; + + xor@60800 { + compatible = "marvell,orion-xor"; + reg = <0x60800 0x100 + 0x60a00 0x100>; + clocks = <&gateclk 22>; + status = "okay"; + + xor00 { + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + dmacap,memcpy; + dmacap,xor; + }; + xor01 { + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; + dmacap,memcpy; + dmacap,xor; + dmacap,memset; + }; + }; + + xor@60900 { + compatible = "marvell,orion-xor"; + reg = <0x60900 0x100 + 0x60b00 0x100>; + clocks = <&gateclk 28>; + status = "okay"; + + xor10 { + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + dmacap,memcpy; + dmacap,xor; + }; + xor11 { + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; + dmacap,memcpy; + dmacap,xor; + dmacap,memset; + }; + }; + + eth0: ethernet@70000 { + compatible = "marvell,armada-370-neta"; + reg = <0x70000 0x4000>; + interrupts-extended = <&mpic 8>; + clocks = <&gateclk 4>; + status = "disabled"; + }; + + mdio { + #address-cells = <1>; + #size-cells = <0>; + compatible = "marvell,orion-mdio"; + reg = <0x72004 0x4>; + }; + + coredivclk: clock@e4250 { + compatible = "marvell,armada-380-corediv-clock"; + reg = <0xe4250 0xc>; + #clock-cells = <1>; + clocks = <&mainpll>; + clock-output-names = "nand"; + }; + + flash@d0000 { + compatible = "marvell,armada370-nand"; + reg = <0xd0000 0x54>; + #address-cells = <1>; + #size-cells = <1>; + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&coredivclk 0>; + status = "disabled"; + }; + }; + }; + + clocks { + /* 2 GHz fixed main PLL */ + mainpll: mainpll { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <2000000000>; + }; + + /* 25 MHz reference crystal */ + refclk: oscillator { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <25000000>; + }; + }; +}; diff --git a/arch/arm/boot/dts/armada-xp-axpwifiap.dts b/arch/arm/boot/dts/armada-xp-axpwifiap.dts index c5fe57269f5a..d83d7d69ac01 100644 --- a/arch/arm/boot/dts/armada-xp-axpwifiap.dts +++ b/arch/arm/boot/dts/armada-xp-axpwifiap.dts @@ -16,6 +16,8 @@ */ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> #include "armada-xp-mv78230.dtsi" / { @@ -157,8 +159,8 @@ button@1 { label = "Factory Reset Button"; - linux,code = <141>; /* KEY_SETUP */ - gpios = <&gpio1 1 1>; + linux,code = <KEY_SETUP>; + gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; }; }; }; diff --git a/arch/arm/boot/dts/armada-xp-db.dts b/arch/arm/boot/dts/armada-xp-db.dts index bcf6d79a57ec..448373c4b0e5 100644 --- a/arch/arm/boot/dts/armada-xp-db.dts +++ b/arch/arm/boot/dts/armada-xp-db.dts @@ -2,7 +2,7 @@ * Device Tree file for Marvell Armada XP evaluation board * (DB-78460-BP) * - * Copyright (C) 2012 Marvell + * Copyright (C) 2012-2014 Marvell * * Lior Amsalem <alior@marvell.com> * Gregory CLEMENT <gregory.clement@free-electrons.com> @@ -11,6 +11,15 @@ * This file is licensed under the terms of the GNU General Public * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. + * + * Note: this Device Tree assumes that the bootloader has remapped the + * internal registers to 0xf1000000 (instead of the default + * 0xd0000000). The 0xf1000000 is the default used by the recent, + * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier + * boards were delivered with an older version of the bootloader that + * left internal registers mapped at 0xd0000000. If you are in this + * situation, you should either update your bootloader (preferred + * solution) or the below Device Tree should be adjusted. */ /dts-v1/; @@ -30,7 +39,7 @@ }; soc { - ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000 + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>; diff --git a/arch/arm/boot/dts/armada-xp-gp.dts b/arch/arm/boot/dts/armada-xp-gp.dts index 274e2ad5f51c..61bda687f782 100644 --- a/arch/arm/boot/dts/armada-xp-gp.dts +++ b/arch/arm/boot/dts/armada-xp-gp.dts @@ -2,7 +2,7 @@ * Device Tree file for Marvell Armada XP development board * (DB-MV784MP-GP) * - * Copyright (C) 2013 Marvell + * Copyright (C) 2013-2014 Marvell * * Lior Amsalem <alior@marvell.com> * Gregory CLEMENT <gregory.clement@free-electrons.com> @@ -11,6 +11,15 @@ * This file is licensed under the terms of the GNU General Public * License version 2. This program is licensed "as is" without any * warranty of any kind, whether express or implied. + * + * Note: this Device Tree assumes that the bootloader has remapped the + * internal registers to 0xf1000000 (instead of the default + * 0xd0000000). The 0xf1000000 is the default used by the recent, + * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier + * boards were delivered with an older version of the bootloader that + * left internal registers mapped at 0xd0000000. If you are in this + * situation, you should either update your bootloader (preferred + * solution) or the below Device Tree should be adjusted. */ /dts-v1/; @@ -30,16 +39,17 @@ * 8 GB of plug-in RAM modules by default.The amount * of memory available can be changed by the * bootloader according the size of the module - * actually plugged. Only 7GB are usable because - * addresses from 0xC0000000 to 0xffffffff are used by - * the internal registers of the SoC. + * actually plugged. However, memory between + * 0xF0000000 to 0xFFFFFFFF cannot be used, as it is + * the address range used for I/O (internal registers, + * MBus windows). */ - reg = <0x00000000 0x00000000 0x00000000 0xC0000000>, + reg = <0x00000000 0x00000000 0x00000000 0xf0000000>, <0x00000001 0x00000000 0x00000001 0x00000000>; }; soc { - ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000 + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000 MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000 MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000>; diff --git a/arch/arm/boot/dts/armada-xp-matrix.dts b/arch/arm/boot/dts/armada-xp-matrix.dts index e47c49ecd55c..c2242745b9b8 100644 --- a/arch/arm/boot/dts/armada-xp-matrix.dts +++ b/arch/arm/boot/dts/armada-xp-matrix.dts @@ -23,7 +23,12 @@ memory { device_type = "memory"; - reg = <0 0x00000000 0 0x80000000>; /* 2 GB */ + /* + * This board has 4 GB of RAM, but the last 256 MB of + * RAM are not usable due to the overlap with the MBus + * Window address range + */ + reg = <0 0x00000000 0 0xf0000000>; }; soc { diff --git a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts index 99bcf76e6953..985948ce67b3 100644 --- a/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts +++ b/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts @@ -11,6 +11,8 @@ */ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> #include "armada-xp-mv78260.dtsi" / { @@ -90,19 +92,19 @@ red_led { label = "red_led"; - gpios = <&gpio1 17 1>; + gpios = <&gpio1 17 GPIO_ACTIVE_LOW>; default-state = "off"; }; yellow_led { label = "yellow_led"; - gpios = <&gpio1 19 1>; + gpios = <&gpio1 19 GPIO_ACTIVE_LOW>; default-state = "off"; }; green_led { label = "green_led"; - gpios = <&gpio1 21 1>; + gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; default-state = "keep"; }; }; @@ -114,8 +116,8 @@ button@1 { label = "Init Button"; - linux,code = <116>; - gpios = <&gpio1 28 0>; + linux,code = <KEY_POWER>; + gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; }; }; diff --git a/arch/arm/boot/dts/armada-xp.dtsi b/arch/arm/boot/dts/armada-xp.dtsi index b8b84a22f0f3..abb9f9dcc525 100644 --- a/arch/arm/boot/dts/armada-xp.dtsi +++ b/arch/arm/boot/dts/armada-xp.dtsi @@ -111,6 +111,12 @@ clock-names = "nbclk", "fixed"; }; + watchdog@20300 { + compatible = "marvell,armada-xp-wdt"; + clocks = <&coreclk 2>, <&refclk>; + clock-names = "nbclk", "fixed"; + }; + armada-370-xp-pmsu@22000 { compatible = "marvell,armada-370-xp-pmsu"; reg = <0x22100 0x400>, <0x20800 0x20>; diff --git a/arch/arm/boot/dts/at91-ariag25.dts b/arch/arm/boot/dts/at91-ariag25.dts index cce45f5177f9..55ab6180e350 100644 --- a/arch/arm/boot/dts/at91-ariag25.dts +++ b/arch/arm/boot/dts/at91-ariag25.dts @@ -129,7 +129,6 @@ adc0: adc@f804c000 { status = "okay"; atmel,adc-channels-used = <0xf>; - atmel,adc-num-channels = <4>; }; dbgu: serial@fffff200 { diff --git a/arch/arm/boot/dts/at91-cosino.dtsi b/arch/arm/boot/dts/at91-cosino.dtsi index 2093c4d7cd6a..df4b78695695 100644 --- a/arch/arm/boot/dts/at91-cosino.dtsi +++ b/arch/arm/boot/dts/at91-cosino.dtsi @@ -64,7 +64,6 @@ }; adc0: adc@f804c000 { - atmel,adc-clock-rate = <1000000>; atmel,adc-ts-wires = <4>; atmel,adc-ts-pressure-threshold = <10000>; status = "okay"; diff --git a/arch/arm/boot/dts/at91-cosino_mega2560.dts b/arch/arm/boot/dts/at91-cosino_mega2560.dts index f9415dd11f17..a542d5837a17 100644 --- a/arch/arm/boot/dts/at91-cosino_mega2560.dts +++ b/arch/arm/boot/dts/at91-cosino_mega2560.dts @@ -27,7 +27,6 @@ }; adc0: adc@f804c000 { - atmel,adc-clock-rate = <1000000>; atmel,adc-ts-wires = <4>; atmel,adc-ts-pressure-threshold = <10000>; status = "okay"; diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi index 997901f7ed73..366fc2cbcd64 100644 --- a/arch/arm/boot/dts/at91sam9260.dtsi +++ b/arch/arm/boot/dts/at91sam9260.dtsi @@ -608,37 +608,38 @@ }; adc0: adc@fffe0000 { + #address-cells = <1>; + #size-cells = <0>; compatible = "atmel,at91sam9260-adc"; reg = <0xfffe0000 0x100>; interrupts = <5 IRQ_TYPE_LEVEL_HIGH 0>; atmel,adc-use-external-triggers; atmel,adc-channels-used = <0xf>; atmel,adc-vref = <3300>; - atmel,adc-num-channels = <4>; atmel,adc-startup-time = <15>; - atmel,adc-channel-base = <0x30>; - atmel,adc-drdy-mask = <0x10000>; - atmel,adc-status-register = <0x1c>; - atmel,adc-trigger-register = <0x04>; atmel,adc-res = <8 10>; atmel,adc-res-names = "lowres", "highres"; atmel,adc-use-res = "highres"; trigger@0 { + reg = <0>; trigger-name = "timer-counter-0"; trigger-value = <0x1>; }; trigger@1 { + reg = <1>; trigger-name = "timer-counter-1"; trigger-value = <0x3>; }; trigger@2 { + reg = <2>; trigger-name = "timer-counter-2"; trigger-value = <0x5>; }; trigger@3 { + reg = <3>; trigger-name = "external"; trigger-value = <0x13>; trigger-external; diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi index cbcc058b26b4..9cdaecff13b3 100644 --- a/arch/arm/boot/dts/at91sam9g45.dtsi +++ b/arch/arm/boot/dts/at91sam9g45.dtsi @@ -632,40 +632,41 @@ }; adc0: adc@fffb0000 { + #address-cells = <1>; + #size-cells = <0>; compatible = "atmel,at91sam9260-adc"; reg = <0xfffb0000 0x100>; interrupts = <20 IRQ_TYPE_LEVEL_HIGH 0>; atmel,adc-use-external-triggers; atmel,adc-channels-used = <0xff>; atmel,adc-vref = <3300>; - atmel,adc-num-channels = <8>; atmel,adc-startup-time = <40>; - atmel,adc-channel-base = <0x30>; - atmel,adc-drdy-mask = <0x10000>; - atmel,adc-status-register = <0x1c>; - atmel,adc-trigger-register = <0x08>; atmel,adc-res = <8 10>; atmel,adc-res-names = "lowres", "highres"; atmel,adc-use-res = "highres"; trigger@0 { + reg = <0>; trigger-name = "external-rising"; trigger-value = <0x1>; trigger-external; }; trigger@1 { + reg = <1>; trigger-name = "external-falling"; trigger-value = <0x2>; trigger-external; }; trigger@2 { + reg = <2>; trigger-name = "external-any"; trigger-value = <0x3>; trigger-external; }; trigger@3 { + reg = <3>; trigger-name = "continuous"; trigger-value = <0x6>; }; @@ -817,6 +818,7 @@ >; atmel,nand-addr-offset = <21>; atmel,nand-cmd-offset = <22>; + atmel,nand-has-dma; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; gpios = <&pioC 8 GPIO_ACTIVE_HIGH diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi index 394e6ce2afb7..9f04808fc697 100644 --- a/arch/arm/boot/dts/at91sam9n12.dtsi +++ b/arch/arm/boot/dts/at91sam9n12.dtsi @@ -570,6 +570,7 @@ atmel,pmecc-lookup-table-offset = <0x0 0x8000>; atmel,nand-addr-offset = <21>; atmel,nand-cmd-offset = <22>; + atmel,nand-has-dma; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; gpios = <&pioD 5 GPIO_ACTIVE_HIGH diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index 174219de92fa..fc13c9240da8 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -621,41 +621,42 @@ }; adc0: adc@f804c000 { + #address-cells = <1>; + #size-cells = <0>; compatible = "atmel,at91sam9260-adc"; reg = <0xf804c000 0x100>; interrupts = <19 IRQ_TYPE_LEVEL_HIGH 0>; - atmel,adc-use-external; + atmel,adc-use-external-triggers; atmel,adc-channels-used = <0xffff>; atmel,adc-vref = <3300>; - atmel,adc-num-channels = <12>; atmel,adc-startup-time = <40>; - atmel,adc-channel-base = <0x50>; - atmel,adc-drdy-mask = <0x1000000>; - atmel,adc-status-register = <0x30>; - atmel,adc-trigger-register = <0xc0>; atmel,adc-res = <8 10>; atmel,adc-res-names = "lowres", "highres"; atmel,adc-use-res = "highres"; trigger@0 { + reg = <0>; trigger-name = "external-rising"; trigger-value = <0x1>; trigger-external; }; trigger@1 { + reg = <1>; trigger-name = "external-falling"; trigger-value = <0x2>; trigger-external; }; trigger@2 { + reg = <2>; trigger-name = "external-any"; trigger-value = <0x3>; trigger-external; }; trigger@3 { + reg = <3>; trigger-name = "continuous"; trigger-value = <0x6>; }; @@ -790,6 +791,7 @@ atmel,pmecc-lookup-table-offset = <0x0 0x8000>; atmel,nand-addr-offset = <21>; atmel,nand-cmd-offset = <22>; + atmel,nand-has-dma; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand>; gpios = <&pioD 5 GPIO_ACTIVE_HIGH diff --git a/arch/arm/boot/dts/bcm11351.dtsi b/arch/arm/boot/dts/bcm11351.dtsi index 792fde1b7f75..64d069bcc409 100644 --- a/arch/arm/boot/dts/bcm11351.dtsi +++ b/arch/arm/boot/dts/bcm11351.dtsi @@ -14,6 +14,8 @@ #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/interrupt-controller/irq.h> +#include "dt-bindings/clock/bcm281xx.h" + #include "skeleton.dtsi" / { @@ -43,7 +45,7 @@ compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart"; status = "disabled"; reg = <0x3e000000 0x1000>; - clocks = <&uartb_clk>; + clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB>; interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; @@ -53,7 +55,7 @@ compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart"; status = "disabled"; reg = <0x3e001000 0x1000>; - clocks = <&uartb2_clk>; + clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB2>; interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; @@ -63,7 +65,7 @@ compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart"; status = "disabled"; reg = <0x3e002000 0x1000>; - clocks = <&uartb3_clk>; + clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB3>; interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; @@ -73,7 +75,7 @@ compatible = "brcm,bcm11351-dw-apb-uart", "snps,dw-apb-uart"; status = "disabled"; reg = <0x3e003000 0x1000>; - clocks = <&uartb4_clk>; + clocks = <&slave_ccu BCM281XX_SLAVE_CCU_UARTB4>; interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; @@ -95,7 +97,7 @@ compatible = "brcm,kona-timer"; reg = <0x35006000 0x1000>; interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&hub_timer_clk>; + clocks = <&aon_ccu BCM281XX_AON_CCU_HUB_TIMER>; }; gpio: gpio@35003000 { @@ -118,7 +120,7 @@ compatible = "brcm,kona-sdhci"; reg = <0x3f180000 0x10000>; interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&sdio1_clk>; + clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO1>; status = "disabled"; }; @@ -126,7 +128,7 @@ compatible = "brcm,kona-sdhci"; reg = <0x3f190000 0x10000>; interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&sdio2_clk>; + clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO2>; status = "disabled"; }; @@ -134,7 +136,7 @@ compatible = "brcm,kona-sdhci"; reg = <0x3f1a0000 0x10000>; interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&sdio3_clk>; + clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO3>; status = "disabled"; }; @@ -142,7 +144,7 @@ compatible = "brcm,kona-sdhci"; reg = <0x3f1b0000 0x10000>; interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&sdio4_clk>; + clocks = <&master_ccu BCM281XX_MASTER_CCU_SDIO4>; status = "disabled"; }; @@ -157,7 +159,7 @@ interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; - clocks = <&bsc1_clk>; + clocks = <&slave_ccu BCM281XX_SLAVE_CCU_BSC1>; status = "disabled"; }; @@ -167,7 +169,7 @@ interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; - clocks = <&bsc2_clk>; + clocks = <&slave_ccu BCM281XX_SLAVE_CCU_BSC2>; status = "disabled"; }; @@ -177,7 +179,7 @@ interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; - clocks = <&bsc3_clk>; + clocks = <&slave_ccu BCM281XX_SLAVE_CCU_BSC3>; status = "disabled"; }; @@ -187,105 +189,191 @@ interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; - clocks = <&pmu_bsc_clk>; + clocks = <&aon_ccu BCM281XX_AON_CCU_PMU_BSC>; status = "disabled"; }; clocks { - bsc1_clk: bsc1 { - compatible = "fixed-clock"; - clock-frequency = <13000000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + root_ccu: root_ccu { + compatible = "brcm,bcm11351-root-ccu"; + reg = <0x35001000 0x0f00>; + #clock-cells = <1>; + clock-output-names = "frac_1m"; + }; + + hub_ccu: hub_ccu { + compatible = "brcm,bcm11351-hub-ccu"; + reg = <0x34000000 0x0f00>; + #clock-cells = <1>; + clock-output-names = "tmon_1m"; + }; + + aon_ccu: aon_ccu { + compatible = "brcm,bcm11351-aon-ccu"; + reg = <0x35002000 0x0f00>; + #clock-cells = <1>; + clock-output-names = "hub_timer", + "pmu_bsc", + "pmu_bsc_var"; + }; + + master_ccu: master_ccu { + compatible = "brcm,bcm11351-master-ccu"; + reg = <0x3f001000 0x0f00>; + #clock-cells = <1>; + clock-output-names = "sdio1", + "sdio2", + "sdio3", + "sdio4", + "usb_ic", + "hsic2_48m", + "hsic2_12m"; + }; + + slave_ccu: slave_ccu { + compatible = "brcm,bcm11351-slave-ccu"; + reg = <0x3e011000 0x0f00>; + #clock-cells = <1>; + clock-output-names = "uartb", + "uartb2", + "uartb3", + "uartb4", + "ssp0", + "ssp2", + "bsc1", + "bsc2", + "bsc3", + "pwm"; + }; + + ref_1m_clk: ref_1m { #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <1000000>; }; - bsc2_clk: bsc2 { + ref_32k_clk: ref_32k { + #clock-cells = <0>; compatible = "fixed-clock"; - clock-frequency = <13000000>; + clock-frequency = <32768>; + }; + + bbl_32k_clk: bbl_32k { #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <32768>; }; - bsc3_clk: bsc3 { + ref_13m_clk: ref_13m { + #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <13000000>; - #clock-cells = <0>; }; - pmu_bsc_clk: pmu_bsc { + var_13m_clk: var_13m { + #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <13000000>; - #clock-cells = <0>; }; - hub_timer_clk: hub_timer { - compatible = "fixed-clock"; - clock-frequency = <32768>; + dft_19_5m_clk: dft_19_5m { #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <19500000>; }; - pwm_clk: pwm { + ref_crystal_clk: ref_crystal { + #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <26000000>; - #clock-cells = <0>; }; - sdio1_clk: sdio1 { - compatible = "fixed-clock"; - clock-frequency = <48000000>; + ref_cx40_clk: ref_cx40 { #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <40000000>; }; - sdio2_clk: sdio2 { - compatible = "fixed-clock"; - clock-frequency = <48000000>; + ref_52m_clk: ref_52m { #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <52000000>; }; - sdio3_clk: sdio3 { - compatible = "fixed-clock"; - clock-frequency = <48000000>; + var_52m_clk: var_52m { #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <52000000>; }; - sdio4_clk: sdio4 { + usb_otg_ahb_clk: usb_otg_ahb { compatible = "fixed-clock"; - clock-frequency = <48000000>; + clock-frequency = <52000000>; #clock-cells = <0>; }; - tmon_1m_clk: tmon_1m { - compatible = "fixed-clock"; - clock-frequency = <1000000>; + ref_96m_clk: ref_96m { #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <96000000>; }; - uartb_clk: uartb { - compatible = "fixed-clock"; - clock-frequency = <13000000>; + var_96m_clk: var_96m { #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <96000000>; }; - uartb2_clk: uartb2 { + ref_104m_clk: ref_104m { + #clock-cells = <0>; compatible = "fixed-clock"; - clock-frequency = <13000000>; + clock-frequency = <104000000>; + }; + + var_104m_clk: var_104m { #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <104000000>; }; - uartb3_clk: uartb3 { + ref_156m_clk: ref_156m { + #clock-cells = <0>; compatible = "fixed-clock"; - clock-frequency = <13000000>; + clock-frequency = <156000000>; + }; + + var_156m_clk: var_156m { #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <156000000>; }; - uartb4_clk: uartb4 { + ref_208m_clk: ref_208m { + #clock-cells = <0>; compatible = "fixed-clock"; - clock-frequency = <13000000>; + clock-frequency = <208000000>; + }; + + var_208m_clk: var_208m { #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <208000000>; }; - usb_otg_ahb_clk: usb_otg_ahb { + ref_312m_clk: ref_312m { + #clock-cells = <0>; compatible = "fixed-clock"; - clock-frequency = <52000000>; + clock-frequency = <312000000>; + }; + + var_312m_clk: var_312m { #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <312000000>; }; }; diff --git a/arch/arm/boot/dts/bcm11351-brt.dts b/arch/arm/boot/dts/bcm21664-garnet.dts index 396b70459cdc..e87cb26ddf84 100644 --- a/arch/arm/boot/dts/bcm11351-brt.dts +++ b/arch/arm/boot/dts/bcm21664-garnet.dts @@ -1,5 +1,5 @@ /* - * Copyright (C) 2012 Broadcom Corporation + * Copyright (C) 2014 Broadcom Corporation * * This program is free software; you can redistribute it and/or * modify it under the terms of the GNU General Public License as @@ -13,11 +13,13 @@ /dts-v1/; -#include "bcm11351.dtsi" +#include <dt-bindings/gpio/gpio.h> + +#include "bcm21664.dtsi" / { - model = "BCM11351 BRT board"; - compatible = "brcm,bcm11351-brt", "brcm,bcm11351"; + model = "BCM21664 Garnet board"; + compatible = "brcm,bcm21664-garnet", "brcm,bcm21664"; memory { reg = <0x80000000 0x40000000>; /* 1 GB */ @@ -40,7 +42,7 @@ sdio4: sdio@3f1b0000 { max-frequency = <48000000>; - cd-gpios = <&gpio 14 0>; + cd-gpios = <&gpio 91 GPIO_ACTIVE_LOW>; status = "okay"; }; diff --git a/arch/arm/boot/dts/bcm21664.dtsi b/arch/arm/boot/dts/bcm21664.dtsi new file mode 100644 index 000000000000..08a44d41b672 --- /dev/null +++ b/arch/arm/boot/dts/bcm21664.dtsi @@ -0,0 +1,292 @@ +/* + * Copyright (C) 2014 Broadcom Corporation + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation version 2. + * + * This program is distributed "as is" WITHOUT ANY WARRANTY of any + * kind, whether express or implied; without even the implied warranty + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/interrupt-controller/irq.h> + +#include "skeleton.dtsi" + +/ { + model = "BCM21664 SoC"; + compatible = "brcm,bcm21664"; + interrupt-parent = <&gic>; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gic: interrupt-controller@3ff00100 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <0>; + interrupt-controller; + reg = <0x3ff01000 0x1000>, + <0x3ff00100 0x100>; + }; + + smc@0x3404e000 { + compatible = "brcm,bcm21664-smc", "brcm,kona-smc"; + reg = <0x3404e000 0x400>; /* 1 KiB in SRAM */ + }; + + uart@3e000000 { + compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart"; + status = "disabled"; + reg = <0x3e000000 0x118>; + clocks = <&uartb_clk>; + interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + }; + + uart@3e001000 { + compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart"; + status = "disabled"; + reg = <0x3e001000 0x118>; + clocks = <&uartb2_clk>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + }; + + uart@3e002000 { + compatible = "brcm,bcm21664-dw-apb-uart", "snps,dw-apb-uart"; + status = "disabled"; + reg = <0x3e002000 0x118>; + clocks = <&uartb3_clk>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + }; + + L2: l2-cache { + compatible = "arm,pl310-cache"; + reg = <0x3ff20000 0x1000>; + cache-unified; + cache-level = <2>; + }; + + brcm,resetmgr@35001f00 { + compatible = "brcm,bcm21664-resetmgr"; + reg = <0x35001f00 0x24>; + }; + + timer@35006000 { + compatible = "brcm,kona-timer"; + reg = <0x35006000 0x1c>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&hub_timer_clk>; + }; + + gpio: gpio@35003000 { + compatible = "brcm,bcm21664-gpio", "brcm,kona-gpio"; + reg = <0x35003000 0x524>; + interrupts = + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH + GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; + #gpio-cells = <2>; + #interrupt-cells = <2>; + gpio-controller; + interrupt-controller; + }; + + sdio1: sdio@3f180000 { + compatible = "brcm,kona-sdhci"; + reg = <0x3f180000 0x801c>; + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sdio1_clk>; + status = "disabled"; + }; + + sdio2: sdio@3f190000 { + compatible = "brcm,kona-sdhci"; + reg = <0x3f190000 0x801c>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sdio2_clk>; + status = "disabled"; + }; + + sdio3: sdio@3f1a0000 { + compatible = "brcm,kona-sdhci"; + reg = <0x3f1a0000 0x801c>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sdio3_clk>; + status = "disabled"; + }; + + sdio4: sdio@3f1b0000 { + compatible = "brcm,kona-sdhci"; + reg = <0x3f1b0000 0x801c>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&sdio4_clk>; + status = "disabled"; + }; + + i2c@3e016000 { + compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c"; + reg = <0x3e016000 0x70>; + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&bsc1_clk>; + status = "disabled"; + }; + + i2c@3e017000 { + compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c"; + reg = <0x3e017000 0x70>; + interrupts = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&bsc2_clk>; + status = "disabled"; + }; + + i2c@3e018000 { + compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c"; + reg = <0x3e018000 0x70>; + interrupts = <GIC_SPI 169 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&bsc3_clk>; + status = "disabled"; + }; + + i2c@3e01c000 { + compatible = "brcm,bcm21664-i2c", "brcm,kona-i2c"; + reg = <0x3e01c000 0x70>; + interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&bsc4_clk>; + status = "disabled"; + }; + + clocks { + bsc1_clk: bsc1 { + compatible = "fixed-clock"; + clock-frequency = <13000000>; + #clock-cells = <0>; + }; + + bsc2_clk: bsc2 { + compatible = "fixed-clock"; + clock-frequency = <13000000>; + #clock-cells = <0>; + }; + + bsc3_clk: bsc3 { + compatible = "fixed-clock"; + clock-frequency = <13000000>; + #clock-cells = <0>; + }; + + bsc4_clk: bsc4 { + compatible = "fixed-clock"; + clock-frequency = <13000000>; + #clock-cells = <0>; + }; + + pmu_bsc_clk: pmu_bsc { + compatible = "fixed-clock"; + clock-frequency = <13000000>; + #clock-cells = <0>; + }; + + hub_timer_clk: hub_timer { + compatible = "fixed-clock"; + clock-frequency = <32768>; + #clock-cells = <0>; + }; + + pwm_clk: pwm { + compatible = "fixed-clock"; + clock-frequency = <26000000>; + #clock-cells = <0>; + }; + + sdio1_clk: sdio1 { + compatible = "fixed-clock"; + clock-frequency = <48000000>; + #clock-cells = <0>; + }; + + sdio2_clk: sdio2 { + compatible = "fixed-clock"; + clock-frequency = <48000000>; + #clock-cells = <0>; + }; + + sdio3_clk: sdio3 { + compatible = "fixed-clock"; + clock-frequency = <48000000>; + #clock-cells = <0>; + }; + + sdio4_clk: sdio4 { + compatible = "fixed-clock"; + clock-frequency = <48000000>; + #clock-cells = <0>; + }; + + tmon_1m_clk: tmon_1m { + compatible = "fixed-clock"; + clock-frequency = <1000000>; + #clock-cells = <0>; + }; + + uartb_clk: uartb { + compatible = "fixed-clock"; + clock-frequency = <13000000>; + #clock-cells = <0>; + }; + + uartb2_clk: uartb2 { + compatible = "fixed-clock"; + clock-frequency = <13000000>; + #clock-cells = <0>; + }; + + uartb3_clk: uartb3 { + compatible = "fixed-clock"; + clock-frequency = <13000000>; + #clock-cells = <0>; + }; + + usb_otg_ahb_clk: usb_otg_ahb { + compatible = "fixed-clock"; + clock-frequency = <52000000>; + #clock-cells = <0>; + }; + }; + + usbotg: usb@3f120000 { + compatible = "snps,dwc2"; + reg = <0x3f120000 0x10000>; + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&usb_otg_ahb_clk>; + clock-names = "otg"; + phys = <&usbphy>; + phy-names = "usb2-phy"; + status = "disabled"; + }; + + usbphy: usb-phy@3f130000 { + compatible = "brcm,kona-usb2-phy"; + reg = <0x3f130000 0x28>; + #phy-cells = <0>; + status = "disabled"; + }; +}; diff --git a/arch/arm/boot/dts/bcm28155-ap.dts b/arch/arm/boot/dts/bcm28155-ap.dts index 5ff2382a49e4..af3da55eef49 100644 --- a/arch/arm/boot/dts/bcm28155-ap.dts +++ b/arch/arm/boot/dts/bcm28155-ap.dts @@ -46,27 +46,32 @@ i2c@3500d000 { status="okay"; - clock-frequency = <400000>; - }; + clock-frequency = <100000>; - sdio1: sdio@3f180000 { - max-frequency = <48000000>; - status = "okay"; + pmu: pmu@8 { + reg = <0x08>; + }; }; sdio2: sdio@3f190000 { non-removable; max-frequency = <48000000>; + vmmc-supply = <&camldo1_reg>; + vqmmc-supply = <&iosr1_reg>; status = "okay"; }; sdio4: sdio@3f1b0000 { max-frequency = <48000000>; cd-gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + vmmc-supply = <&sdldo_reg>; + vqmmc-supply = <&sdxldo_reg>; status = "okay"; }; usbotg: usb@3f120000 { + vusb_d-supply = <&usbldo_reg>; + vusb_a-supply = <&iosr1_reg>; status = "okay"; }; @@ -74,3 +79,39 @@ status = "okay"; }; }; + +#include "bcm59056.dtsi" + +&pmu { + compatible = "brcm,bcm59056"; + interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>; + regulators { + camldo1_reg: camldo1 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + sdldo_reg: sdldo { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + sdxldo_reg: sdxldo { + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + }; + + usbldo_reg: usbldo { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + iosr1_reg: iosr1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + }; +}; diff --git a/arch/arm/boot/dts/bcm2835.dtsi b/arch/arm/boot/dts/bcm2835.dtsi index b021c96d3ba1..b8473c43e888 100644 --- a/arch/arm/boot/dts/bcm2835.dtsi +++ b/arch/arm/boot/dts/bcm2835.dtsi @@ -15,39 +15,52 @@ #size-cells = <1>; ranges = <0x7e000000 0x20000000 0x02000000>; - timer { + timer@7e003000 { compatible = "brcm,bcm2835-system-timer"; reg = <0x7e003000 0x1000>; interrupts = <1 0>, <1 1>, <1 2>, <1 3>; clock-frequency = <1000000>; }; - intc: interrupt-controller { + dma: dma@7e007000 { + compatible = "brcm,bcm2835-dma"; + reg = <0x7e007000 0xf00>; + interrupts = <1 16>, + <1 17>, + <1 18>, + <1 19>, + <1 20>, + <1 21>, + <1 22>, + <1 23>, + <1 24>, + <1 25>, + <1 26>, + <1 27>, + <1 28>; + + #dma-cells = <1>; + brcm,dma-channel-mask = <0x7f35>; + }; + + intc: interrupt-controller@7e00b200 { compatible = "brcm,bcm2835-armctrl-ic"; reg = <0x7e00b200 0x200>; interrupt-controller; #interrupt-cells = <2>; }; - watchdog { + watchdog@7e100000 { compatible = "brcm,bcm2835-pm-wdt"; reg = <0x7e100000 0x28>; }; - rng { + rng@7e104000 { compatible = "brcm,bcm2835-rng"; reg = <0x7e104000 0x10>; }; - uart@20201000 { - compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell"; - reg = <0x7e201000 0x1000>; - interrupts = <2 25>; - clock-frequency = <3000000>; - arm,primecell-periphid = <0x00241011>; - }; - - gpio: gpio { + gpio: gpio@7e200000 { compatible = "brcm,bcm2835-gpio"; reg = <0x7e200000 0xb4>; /* @@ -70,7 +83,25 @@ #interrupt-cells = <2>; }; - spi: spi@20204000 { + uart@7e201000 { + compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell"; + reg = <0x7e201000 0x1000>; + interrupts = <2 25>; + clock-frequency = <3000000>; + arm,primecell-periphid = <0x00241011>; + }; + + i2s: i2s@7e203000 { + compatible = "brcm,bcm2835-i2s"; + reg = <0x7e203000 0x20>, + <0x7e101098 0x02>; + + dmas = <&dma 2>, + <&dma 3>; + dma-names = "tx", "rx"; + }; + + spi: spi@7e204000 { compatible = "brcm,bcm2835-spi"; reg = <0x7e204000 0x1000>; interrupts = <2 22>; @@ -90,7 +121,15 @@ status = "disabled"; }; - i2c1: i2c@20804000 { + sdhci: sdhci@7e300000 { + compatible = "brcm,bcm2835-sdhci"; + reg = <0x7e300000 0x100>; + interrupts = <2 30>; + clocks = <&clk_mmc>; + status = "disabled"; + }; + + i2c1: i2c@7e804000 { compatible = "brcm,bcm2835-i2c"; reg = <0x7e804000 0x1000>; interrupts = <2 21>; @@ -100,19 +139,15 @@ status = "disabled"; }; - sdhci: sdhci { - compatible = "brcm,bcm2835-sdhci"; - reg = <0x7e300000 0x100>; - interrupts = <2 30>; - clocks = <&clk_mmc>; - status = "disabled"; - }; - - usb { + usb@7e980000 { compatible = "brcm,bcm2835-usb"; reg = <0x7e980000 0x10000>; interrupts = <1 9>; }; + + arm-pmu { + compatible = "arm,arm1176-pmu"; + }; }; clocks { @@ -120,24 +155,27 @@ #address-cells = <1>; #size-cells = <0>; - clk_mmc: mmc { + clk_mmc: clock@0 { compatible = "fixed-clock"; reg = <0>; #clock-cells = <0>; + clock-output-names = "mmc"; clock-frequency = <100000000>; }; - clk_i2c: i2c { + clk_i2c: clock@1 { compatible = "fixed-clock"; reg = <1>; #clock-cells = <0>; + clock-output-names = "i2c"; clock-frequency = <250000000>; }; - clk_spi: spi { + clk_spi: clock@2 { compatible = "fixed-clock"; reg = <2>; #clock-cells = <0>; + clock-output-names = "spi"; clock-frequency = <250000000>; }; }; diff --git a/arch/arm/boot/dts/bcm4708-netgear-r6250.dts b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts new file mode 100644 index 000000000000..3b5259de5a38 --- /dev/null +++ b/arch/arm/boot/dts/bcm4708-netgear-r6250.dts @@ -0,0 +1,35 @@ +/* + * Broadcom BCM470X / BCM5301X arm platform code. + * DTS for Netgear R6250 V1 + * + * Copyright 2013 Hauke Mehrtens <hauke@hauke-m.de> + * + * Licensed under the GNU/GPL. See COPYING for details. + */ + +/dts-v1/; + +#include "bcm4708.dtsi" + +/ { + compatible = "netgear,r6250v1", "brcm,bcm4708"; + model = "Netgear R6250 V1 (BCM4708)"; + + chosen { + bootargs = "console=ttyS0,115200"; + }; + + memory { + reg = <0x00000000 0x08000000>; + }; + + chipcommonA { + uart0: serial@0300 { + status = "okay"; + }; + + uart1: serial@0400 { + status = "okay"; + }; + }; +}; diff --git a/arch/arm/boot/dts/bcm4708.dtsi b/arch/arm/boot/dts/bcm4708.dtsi new file mode 100644 index 000000000000..31141e83fedd --- /dev/null +++ b/arch/arm/boot/dts/bcm4708.dtsi @@ -0,0 +1,34 @@ +/* + * Broadcom BCM470X / BCM5301X ARM platform code. + * DTS for BCM4708 SoC. + * + * Copyright 2013-2014 Hauke Mehrtens <hauke@hauke-m.de> + * + * Licensed under the GNU/GPL. See COPYING for details. + */ + +#include "bcm5301x.dtsi" + +/ { + compatible = "brcm,bcm4708"; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + next-level-cache = <&L2>; + reg = <0x0>; + }; + + cpu@1 { + device_type = "cpu"; + compatible = "arm,cortex-a9"; + next-level-cache = <&L2>; + reg = <0x1>; + }; + }; + +}; diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi new file mode 100644 index 000000000000..53c624f766b4 --- /dev/null +++ b/arch/arm/boot/dts/bcm5301x.dtsi @@ -0,0 +1,95 @@ +/* + * Broadcom BCM470X / BCM5301X ARM platform code. + * Generic DTS part for all BCM53010, BCM53011, BCM53012, BCM53014, BCM53015, + * BCM53016, BCM53017, BCM53018, BCM4707, BCM4708 and BCM4709 SoCs + * + * Copyright 2013-2014 Hauke Mehrtens <hauke@hauke-m.de> + * + * Licensed under the GNU/GPL. See COPYING for details. + */ + +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include "skeleton.dtsi" + +/ { + interrupt-parent = <&gic>; + + chipcommonA { + compatible = "simple-bus"; + ranges = <0x00000000 0x18000000 0x00001000>; + #address-cells = <1>; + #size-cells = <1>; + + uart0: serial@0300 { + compatible = "ns16550"; + reg = <0x0300 0x100>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <100000000>; + status = "disabled"; + }; + + uart1: serial@0400 { + compatible = "ns16550"; + reg = <0x0400 0x100>; + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <100000000>; + status = "disabled"; + }; + }; + + mpcore { + compatible = "simple-bus"; + ranges = <0x00000000 0x19020000 0x00003000>; + #address-cells = <1>; + #size-cells = <1>; + + scu@0000 { + compatible = "arm,cortex-a9-scu"; + reg = <0x0000 0x100>; + }; + + timer@0200 { + compatible = "arm,cortex-a9-global-timer"; + reg = <0x0200 0x100>; + interrupts = <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_periph>; + }; + + local-timer@0600 { + compatible = "arm,cortex-a9-twd-timer"; + reg = <0x0600 0x100>; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clk_periph>; + }; + + gic: interrupt-controller@1000 { + compatible = "arm,cortex-a9-gic"; + #interrupt-cells = <3>; + #address-cells = <0>; + interrupt-controller; + reg = <0x1000 0x1000>, + <0x0100 0x100>; + }; + + L2: cache-controller@2000 { + compatible = "arm,pl310-cache"; + reg = <0x2000 0x1000>; + cache-unified; + cache-level = <2>; + }; + }; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + + /* As long as we do not have a real clock driver us this + * fixed clock */ + clk_periph: periph { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <400000000>; + }; + }; +}; diff --git a/arch/arm/boot/dts/bcm59056.dtsi b/arch/arm/boot/dts/bcm59056.dtsi new file mode 100644 index 000000000000..dfadaaa89b05 --- /dev/null +++ b/arch/arm/boot/dts/bcm59056.dtsi @@ -0,0 +1,74 @@ +/* +* Copyright 2014 Linaro Limited +* Author: Matt Porter <mporter@linaro.org> +* +* This program is free software; you can redistribute it and/or modify it +* under the terms of the GNU General Public License as published by the +* Free Software Foundation; either version 2 of the License, or (at your +* option) any later version. +*/ + +&pmu { + compatible = "brcm,bcm59056"; + regulators { + rfldo_reg: rfldo { + }; + + camldo1_reg: camldo1 { + }; + + camldo2_reg: camldo2 { + }; + + simldo1_reg: simldo1 { + }; + + simldo2_reg: simldo2 { + }; + + sdldo_reg: sdldo { + }; + + sdxldo_reg: sdxldo { + }; + + mmcldo1_reg: mmcldo1 { + }; + + mmcldo2_reg: mmcldo2 { + }; + + audldo_reg: audldo { + }; + + micldo_reg: micldo { + }; + + usbldo_reg: usbldo { + }; + + vibldo_reg: vibldo { + }; + + csr_reg: csr { + }; + + iosr1_reg: iosr1 { + }; + + iosr2_reg: iosr2 { + }; + + msr_reg: msr { + }; + + sdsr1_reg: sdsr1 { + }; + + sdsr2_reg: sdsr2 { + }; + + vsr_reg: vsr { + }; + }; +}; diff --git a/arch/arm/boot/dts/dove.dtsi b/arch/arm/boot/dts/dove.dtsi index 187fd46b7b5e..3b891dd20993 100644 --- a/arch/arm/boot/dts/dove.dtsi +++ b/arch/arm/boot/dts/dove.dtsi @@ -186,6 +186,11 @@ reg = <0x20000 0x80>, <0x800100 0x8>; }; + sysc: system-ctrl@20000 { + compatible = "marvell,orion-system-controller"; + reg = <0x20000 0x110>; + }; + bridge_intc: bridge-interrupt-ctrl@20110 { compatible = "marvell,orion-bridge-intc"; interrupt-controller; @@ -210,6 +215,14 @@ clocks = <&core_clk 0>; }; + watchdog@20300 { + compatible = "marvell,orion-wdt"; + reg = <0x20300 0x28>, <0x20108 0x4>; + interrupt-parent = <&bridge_intc>; + interrupts = <3>; + clocks = <&core_clk 0>; + }; + crypto: crypto-engine@30000 { compatible = "marvell,orion-crypto"; reg = <0x30000 0x10000>, @@ -381,7 +394,8 @@ pinctrl: pin-ctrl@d0200 { compatible = "marvell,dove-pinctrl"; - reg = <0xd0200 0x10>; + reg = <0xd0200 0x14>, + <0xd0440 0x04>; clocks = <&gate_clk 22>; pmx_gpio_0: pmx-gpio-0 { @@ -603,6 +617,12 @@ reg = <0xd8500 0x20>; }; + gconf: global-config@e802c { + compatible = "marvell,dove-global-config", + "syscon"; + reg = <0xe802c 0x14>; + }; + gpio2: gpio-ctrl@e8400 { compatible = "marvell,orion-gpio"; #gpio-cells = <2>; diff --git a/arch/arm/boot/dts/dra7.dtsi b/arch/arm/boot/dts/dra7.dtsi index 1fd75aa4639d..9e3caf3d19fb 100644 --- a/arch/arm/boot/dts/dra7.dtsi +++ b/arch/arm/boot/dts/dra7.dtsi @@ -47,6 +47,11 @@ 1000000 1060000 1176000 1160000 >; + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ }; cpu@1 { device_type = "cpu"; @@ -464,6 +469,20 @@ ti,hwmods = "wd_timer2"; }; + hwspinlock: spinlock@4a0f6000 { + compatible = "ti,omap4-hwspinlock"; + reg = <0x4a0f6000 0x1000>; + ti,hwmods = "spinlock"; + #hwlock-cells = <1>; + }; + + dmm@4e000000 { + compatible = "ti,omap5-dmm"; + reg = <0x4e000000 0x800>; + interrupts = <0 113 0x4>; + ti,hwmods = "dmm"; + }; + i2c1: i2c@48070000 { compatible = "ti,omap4-i2c"; reg = <0x48070000 0x100>; @@ -559,6 +578,138 @@ status = "disabled"; }; + abb_mpu: regulator-abb-mpu { + compatible = "ti,abb-v3"; + regulator-name = "abb_mpu"; + #address-cells = <0>; + #size-cells = <0>; + clocks = <&sys_clkin1>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + + reg = <0x4ae07ddc 0x4>, <0x4ae07de0 0x4>, + <0x4ae06014 0x4>, <0x4a003b20 0x8>, + <0x4ae0c158 0x4>; + reg-names = "setup-address", "control-address", + "int-address", "efuse-address", + "ldo-address"; + ti,tranxdone-status-mask = <0x80>; + /* LDOVBBMPU_FBB_MUX_CTRL */ + ti,ldovbb-override-mask = <0x400>; + /* LDOVBBMPU_FBB_VSET_OUT */ + ti,ldovbb-vset-mask = <0x1F>; + + /* + * NOTE: only FBB mode used but actual vset will + * determine final biasing + */ + ti,abb_info = < + /*uV ABB efuse rbb_m fbb_m vset_m*/ + 1060000 0 0x0 0 0x02000000 0x01F00000 + 1160000 0 0x4 0 0x02000000 0x01F00000 + 1210000 0 0x8 0 0x02000000 0x01F00000 + >; + }; + + abb_ivahd: regulator-abb-ivahd { + compatible = "ti,abb-v3"; + regulator-name = "abb_ivahd"; + #address-cells = <0>; + #size-cells = <0>; + clocks = <&sys_clkin1>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + + reg = <0x4ae07e34 0x4>, <0x4ae07e24 0x4>, + <0x4ae06010 0x4>, <0x4a0025cc 0x8>, + <0x4a002470 0x4>; + reg-names = "setup-address", "control-address", + "int-address", "efuse-address", + "ldo-address"; + ti,tranxdone-status-mask = <0x40000000>; + /* LDOVBBIVA_FBB_MUX_CTRL */ + ti,ldovbb-override-mask = <0x400>; + /* LDOVBBIVA_FBB_VSET_OUT */ + ti,ldovbb-vset-mask = <0x1F>; + + /* + * NOTE: only FBB mode used but actual vset will + * determine final biasing + */ + ti,abb_info = < + /*uV ABB efuse rbb_m fbb_m vset_m*/ + 1055000 0 0x0 0 0x02000000 0x01F00000 + 1150000 0 0x4 0 0x02000000 0x01F00000 + 1250000 0 0x8 0 0x02000000 0x01F00000 + >; + }; + + abb_dspeve: regulator-abb-dspeve { + compatible = "ti,abb-v3"; + regulator-name = "abb_dspeve"; + #address-cells = <0>; + #size-cells = <0>; + clocks = <&sys_clkin1>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + + reg = <0x4ae07e30 0x4>, <0x4ae07e20 0x4>, + <0x4ae06010 0x4>, <0x4a0025e0 0x8>, + <0x4a00246c 0x4>; + reg-names = "setup-address", "control-address", + "int-address", "efuse-address", + "ldo-address"; + ti,tranxdone-status-mask = <0x20000000>; + /* LDOVBBDSPEVE_FBB_MUX_CTRL */ + ti,ldovbb-override-mask = <0x400>; + /* LDOVBBDSPEVE_FBB_VSET_OUT */ + ti,ldovbb-vset-mask = <0x1F>; + + /* + * NOTE: only FBB mode used but actual vset will + * determine final biasing + */ + ti,abb_info = < + /*uV ABB efuse rbb_m fbb_m vset_m*/ + 1055000 0 0x0 0 0x02000000 0x01F00000 + 1150000 0 0x4 0 0x02000000 0x01F00000 + 1250000 0 0x8 0 0x02000000 0x01F00000 + >; + }; + + abb_gpu: regulator-abb-gpu { + compatible = "ti,abb-v3"; + regulator-name = "abb_gpu"; + #address-cells = <0>; + #size-cells = <0>; + clocks = <&sys_clkin1>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + + reg = <0x4ae07de4 0x4>, <0x4ae07de8 0x4>, + <0x4ae06010 0x4>, <0x4a003b08 0x8>, + <0x4ae0c154 0x4>; + reg-names = "setup-address", "control-address", + "int-address", "efuse-address", + "ldo-address"; + ti,tranxdone-status-mask = <0x10000000>; + /* LDOVBBGPU_FBB_MUX_CTRL */ + ti,ldovbb-override-mask = <0x400>; + /* LDOVBBGPU_FBB_VSET_OUT */ + ti,ldovbb-vset-mask = <0x1F>; + + /* + * NOTE: only FBB mode used but actual vset will + * determine final biasing + */ + ti,abb_info = < + /*uV ABB efuse rbb_m fbb_m vset_m*/ + 1090000 0 0x0 0 0x02000000 0x01F00000 + 1210000 0 0x4 0 0x02000000 0x01F00000 + 1280000 0 0x8 0 0x02000000 0x01F00000 + >; + }; + mcspi1: spi@48098000 { compatible = "ti,omap4-mcspi"; reg = <0x48098000 0x200>; diff --git a/arch/arm/boot/dts/efm32gg-dk3750.dts b/arch/arm/boot/dts/efm32gg-dk3750.dts index aa5c0f6363d6..b4031fa4a567 100644 --- a/arch/arm/boot/dts/efm32gg-dk3750.dts +++ b/arch/arm/boot/dts/efm32gg-dk3750.dts @@ -26,7 +26,7 @@ }; i2c@4000a000 { - location = <3>; + efm32,location = <3>; status = "ok"; temp@48 { diff --git a/arch/arm/boot/dts/efm32gg.dtsi b/arch/arm/boot/dts/efm32gg.dtsi index a342ab0e6e4f..106d505c5d3d 100644 --- a/arch/arm/boot/dts/efm32gg.dtsi +++ b/arch/arm/boot/dts/efm32gg.dtsi @@ -84,7 +84,7 @@ status = "disabled"; }; - spi2: spi@40x4000c800 { /* USART2 */ + spi2: spi@4000c800 { /* USART2 */ #address-cells = <1>; #size-cells = <0>; compatible = "efm32,spi"; @@ -110,7 +110,7 @@ status = "disabled"; }; - uart2: uart@40x4000c800 { /* USART2 */ + uart2: uart@4000c800 { /* USART2 */ compatible = "efm32,uart"; reg = <0x4000c800 0x400>; interrupts = <18 19>; diff --git a/arch/arm/boot/dts/exynos4.dtsi b/arch/arm/boot/dts/exynos4.dtsi index 08452e183b57..28b5ec79f339 100644 --- a/arch/arm/boot/dts/exynos4.dtsi +++ b/arch/arm/boot/dts/exynos4.dtsi @@ -19,6 +19,7 @@ * published by the Free Software Foundation. */ +#include <dt-bindings/clock/exynos4.h> #include "skeleton.dtsi" / { @@ -119,7 +120,7 @@ compatible = "samsung,exynos4210-fimc"; reg = <0x11800000 0x1000>; interrupts = <0 84 0>; - clocks = <&clock 256>, <&clock 128>; + clocks = <&clock CLK_FIMC0>, <&clock CLK_SCLK_FIMC0>; clock-names = "fimc", "sclk_fimc"; samsung,power-domain = <&pd_cam>; samsung,sysreg = <&sys_reg>; @@ -130,7 +131,7 @@ compatible = "samsung,exynos4210-fimc"; reg = <0x11810000 0x1000>; interrupts = <0 85 0>; - clocks = <&clock 257>, <&clock 129>; + clocks = <&clock CLK_FIMC1>, <&clock CLK_SCLK_FIMC1>; clock-names = "fimc", "sclk_fimc"; samsung,power-domain = <&pd_cam>; samsung,sysreg = <&sys_reg>; @@ -141,7 +142,7 @@ compatible = "samsung,exynos4210-fimc"; reg = <0x11820000 0x1000>; interrupts = <0 86 0>; - clocks = <&clock 258>, <&clock 130>; + clocks = <&clock CLK_FIMC2>, <&clock CLK_SCLK_FIMC2>; clock-names = "fimc", "sclk_fimc"; samsung,power-domain = <&pd_cam>; samsung,sysreg = <&sys_reg>; @@ -152,7 +153,7 @@ compatible = "samsung,exynos4210-fimc"; reg = <0x11830000 0x1000>; interrupts = <0 87 0>; - clocks = <&clock 259>, <&clock 131>; + clocks = <&clock CLK_FIMC3>, <&clock CLK_SCLK_FIMC3>; clock-names = "fimc", "sclk_fimc"; samsung,power-domain = <&pd_cam>; samsung,sysreg = <&sys_reg>; @@ -163,7 +164,7 @@ compatible = "samsung,exynos4210-csis"; reg = <0x11880000 0x4000>; interrupts = <0 78 0>; - clocks = <&clock 260>, <&clock 134>; + clocks = <&clock CLK_CSIS0>, <&clock CLK_SCLK_CSIS0>; clock-names = "csis", "sclk_csis"; bus-width = <4>; samsung,power-domain = <&pd_cam>; @@ -178,7 +179,7 @@ compatible = "samsung,exynos4210-csis"; reg = <0x11890000 0x4000>; interrupts = <0 80 0>; - clocks = <&clock 261>, <&clock 135>; + clocks = <&clock CLK_CSIS1>, <&clock CLK_SCLK_CSIS1>; clock-names = "csis", "sclk_csis"; bus-width = <2>; samsung,power-domain = <&pd_cam>; @@ -194,7 +195,7 @@ compatible = "samsung,s3c2410-wdt"; reg = <0x10060000 0x100>; interrupts = <0 43 0>; - clocks = <&clock 345>; + clocks = <&clock CLK_WDT>; clock-names = "watchdog"; status = "disabled"; }; @@ -203,7 +204,7 @@ compatible = "samsung,s3c6410-rtc"; reg = <0x10070000 0x100>; interrupts = <0 44 0>, <0 45 0>; - clocks = <&clock 346>; + clocks = <&clock CLK_RTC>; clock-names = "rtc"; status = "disabled"; }; @@ -212,7 +213,7 @@ compatible = "samsung,s5pv210-keypad"; reg = <0x100A0000 0x100>; interrupts = <0 109 0>; - clocks = <&clock 347>; + clocks = <&clock CLK_KEYIF>; clock-names = "keypad"; status = "disabled"; }; @@ -221,7 +222,7 @@ compatible = "samsung,exynos4210-sdhci"; reg = <0x12510000 0x100>; interrupts = <0 73 0>; - clocks = <&clock 297>, <&clock 145>; + clocks = <&clock CLK_SDMMC0>, <&clock CLK_SCLK_MMC0>; clock-names = "hsmmc", "mmc_busclk.2"; status = "disabled"; }; @@ -230,7 +231,7 @@ compatible = "samsung,exynos4210-sdhci"; reg = <0x12520000 0x100>; interrupts = <0 74 0>; - clocks = <&clock 298>, <&clock 146>; + clocks = <&clock CLK_SDMMC1>, <&clock CLK_SCLK_MMC1>; clock-names = "hsmmc", "mmc_busclk.2"; status = "disabled"; }; @@ -239,7 +240,7 @@ compatible = "samsung,exynos4210-sdhci"; reg = <0x12530000 0x100>; interrupts = <0 75 0>; - clocks = <&clock 299>, <&clock 147>; + clocks = <&clock CLK_SDMMC2>, <&clock CLK_SCLK_MMC2>; clock-names = "hsmmc", "mmc_busclk.2"; status = "disabled"; }; @@ -248,7 +249,7 @@ compatible = "samsung,exynos4210-sdhci"; reg = <0x12540000 0x100>; interrupts = <0 76 0>; - clocks = <&clock 300>, <&clock 148>; + clocks = <&clock CLK_SDMMC3>, <&clock CLK_SCLK_MMC3>; clock-names = "hsmmc", "mmc_busclk.2"; status = "disabled"; }; @@ -257,7 +258,7 @@ compatible = "samsung,exynos4210-ehci"; reg = <0x12580000 0x100>; interrupts = <0 70 0>; - clocks = <&clock 304>; + clocks = <&clock CLK_USB_HOST>; clock-names = "usbhost"; status = "disabled"; }; @@ -266,7 +267,7 @@ compatible = "samsung,exynos4210-ohci"; reg = <0x12590000 0x100>; interrupts = <0 70 0>; - clocks = <&clock 304>; + clocks = <&clock CLK_USB_HOST>; clock-names = "usbhost"; status = "disabled"; }; @@ -276,7 +277,7 @@ reg = <0x13400000 0x10000>; interrupts = <0 94 0>; samsung,power-domain = <&pd_mfc>; - clocks = <&clock 273>; + clocks = <&clock CLK_MFC>; clock-names = "mfc"; status = "disabled"; }; @@ -285,7 +286,7 @@ compatible = "samsung,exynos4210-uart"; reg = <0x13800000 0x100>; interrupts = <0 52 0>; - clocks = <&clock 312>, <&clock 151>; + clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>; clock-names = "uart", "clk_uart_baud0"; status = "disabled"; }; @@ -294,7 +295,7 @@ compatible = "samsung,exynos4210-uart"; reg = <0x13810000 0x100>; interrupts = <0 53 0>; - clocks = <&clock 313>, <&clock 152>; + clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>; clock-names = "uart", "clk_uart_baud0"; status = "disabled"; }; @@ -303,7 +304,7 @@ compatible = "samsung,exynos4210-uart"; reg = <0x13820000 0x100>; interrupts = <0 54 0>; - clocks = <&clock 314>, <&clock 153>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; status = "disabled"; }; @@ -312,7 +313,7 @@ compatible = "samsung,exynos4210-uart"; reg = <0x13830000 0x100>; interrupts = <0 55 0>; - clocks = <&clock 315>, <&clock 154>; + clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>; clock-names = "uart", "clk_uart_baud0"; status = "disabled"; }; @@ -323,7 +324,7 @@ compatible = "samsung,s3c2440-i2c"; reg = <0x13860000 0x100>; interrupts = <0 58 0>; - clocks = <&clock 317>; + clocks = <&clock CLK_I2C0>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c0_bus>; @@ -336,7 +337,7 @@ compatible = "samsung,s3c2440-i2c"; reg = <0x13870000 0x100>; interrupts = <0 59 0>; - clocks = <&clock 318>; + clocks = <&clock CLK_I2C1>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c1_bus>; @@ -349,7 +350,7 @@ compatible = "samsung,s3c2440-i2c"; reg = <0x13880000 0x100>; interrupts = <0 60 0>; - clocks = <&clock 319>; + clocks = <&clock CLK_I2C2>; clock-names = "i2c"; status = "disabled"; }; @@ -360,7 +361,7 @@ compatible = "samsung,s3c2440-i2c"; reg = <0x13890000 0x100>; interrupts = <0 61 0>; - clocks = <&clock 320>; + clocks = <&clock CLK_I2C3>; clock-names = "i2c"; status = "disabled"; }; @@ -371,7 +372,7 @@ compatible = "samsung,s3c2440-i2c"; reg = <0x138A0000 0x100>; interrupts = <0 62 0>; - clocks = <&clock 321>; + clocks = <&clock CLK_I2C4>; clock-names = "i2c"; status = "disabled"; }; @@ -382,7 +383,7 @@ compatible = "samsung,s3c2440-i2c"; reg = <0x138B0000 0x100>; interrupts = <0 63 0>; - clocks = <&clock 322>; + clocks = <&clock CLK_I2C5>; clock-names = "i2c"; status = "disabled"; }; @@ -393,7 +394,7 @@ compatible = "samsung,s3c2440-i2c"; reg = <0x138C0000 0x100>; interrupts = <0 64 0>; - clocks = <&clock 323>; + clocks = <&clock CLK_I2C6>; clock-names = "i2c"; status = "disabled"; }; @@ -404,7 +405,7 @@ compatible = "samsung,s3c2440-i2c"; reg = <0x138D0000 0x100>; interrupts = <0 65 0>; - clocks = <&clock 324>; + clocks = <&clock CLK_I2C7>; clock-names = "i2c"; status = "disabled"; }; @@ -417,7 +418,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 327>, <&clock 159>; + clocks = <&clock CLK_SPI0>, <&clock CLK_SCLK_SPI0>; clock-names = "spi", "spi_busclk0"; pinctrl-names = "default"; pinctrl-0 = <&spi0_bus>; @@ -432,7 +433,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 328>, <&clock 160>; + clocks = <&clock CLK_SPI1>, <&clock CLK_SCLK_SPI1>; clock-names = "spi", "spi_busclk0"; pinctrl-names = "default"; pinctrl-0 = <&spi1_bus>; @@ -447,7 +448,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 329>, <&clock 161>; + clocks = <&clock CLK_SPI2>, <&clock CLK_SCLK_SPI2>; clock-names = "spi", "spi_busclk0"; pinctrl-names = "default"; pinctrl-0 = <&spi2_bus>; @@ -458,7 +459,7 @@ compatible = "samsung,exynos4210-pwm"; reg = <0x139D0000 0x1000>; interrupts = <0 37 0>, <0 38 0>, <0 39 0>, <0 40 0>, <0 41 0>; - clocks = <&clock 336>; + clocks = <&clock CLK_PWM>; clock-names = "timers"; #pwm-cells = <2>; status = "disabled"; @@ -475,7 +476,7 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x12680000 0x1000>; interrupts = <0 35 0>; - clocks = <&clock 292>; + clocks = <&clock CLK_PDMA0>; clock-names = "apb_pclk"; #dma-cells = <1>; #dma-channels = <8>; @@ -486,7 +487,7 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x12690000 0x1000>; interrupts = <0 36 0>; - clocks = <&clock 293>; + clocks = <&clock CLK_PDMA1>; clock-names = "apb_pclk"; #dma-cells = <1>; #dma-channels = <8>; @@ -497,7 +498,7 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x12850000 0x1000>; interrupts = <0 34 0>; - clocks = <&clock 279>; + clocks = <&clock CLK_MDMA>; clock-names = "apb_pclk"; #dma-cells = <1>; #dma-channels = <8>; @@ -511,7 +512,7 @@ reg = <0x11c00000 0x20000>; interrupt-names = "fifo", "vsync", "lcd_sys"; interrupts = <11 0>, <11 1>, <11 2>; - clocks = <&clock 140>, <&clock 283>; + clocks = <&clock CLK_SCLK_FIMD0>, <&clock CLK_FIMD0>; clock-names = "sclk_fimd", "fimd"; samsung,power-domain = <&pd_lcd0>; status = "disabled"; diff --git a/arch/arm/boot/dts/exynos4210.dtsi b/arch/arm/boot/dts/exynos4210.dtsi index 48ecd7a755ab..cb0e768dc6d4 100644 --- a/arch/arm/boot/dts/exynos4210.dtsi +++ b/arch/arm/boot/dts/exynos4210.dtsi @@ -53,7 +53,7 @@ reg = <0x10050000 0x800>; interrupt-parent = <&mct_map>; interrupts = <0>, <1>, <2>, <3>, <4>, <5>; - clocks = <&clock 3>, <&clock 344>; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>; clock-names = "fin_pll", "mct"; mct_map: mct-map { @@ -109,7 +109,7 @@ interrupt-parent = <&combiner>; reg = <0x100C0000 0x100>; interrupts = <2 4>; - clocks = <&clock 383>; + clocks = <&clock CLK_TMU_APBIF>; clock-names = "tmu_apbif"; status = "disabled"; }; @@ -118,13 +118,14 @@ compatible = "samsung,s5pv210-g2d"; reg = <0x12800000 0x1000>; interrupts = <0 89 0>; - clocks = <&clock 177>, <&clock 277>; + clocks = <&clock CLK_SCLK_FIMG2D>, <&clock CLK_G2D>; clock-names = "sclk_fimg2d", "fimg2d"; status = "disabled"; }; camera { - clocks = <&clock 132>, <&clock 133>, <&clock 351>, <&clock 352>; + clocks = <&clock CLK_SCLK_CAM0>, <&clock CLK_SCLK_CAM1>, + <&clock CLK_PIXELASYNCM0>, <&clock CLK_PIXELASYNCM1>; clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", "pxl_async1"; fimc_0: fimc@11800000 { diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts index 9804fcb71f8c..12459b01cca3 100644 --- a/arch/arm/boot/dts/exynos4412-odroidx.dts +++ b/arch/arm/boot/dts/exynos4412-odroidx.dts @@ -251,7 +251,7 @@ buck2_reg: BUCK2 { regulator-name = "vdd_arm"; regulator-min-microvolt = <900000>; - regulator-max-microvolt = <1300000>; + regulator-max-microvolt = <1350000>; regulator-always-on; regulator-boot-on; }; diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/exynos4412-origen.dts index 6bc053924e9e..388f03579661 100644 --- a/arch/arm/boot/dts/exynos4412-origen.dts +++ b/arch/arm/boot/dts/exynos4412-origen.dts @@ -459,8 +459,8 @@ buck2_reg: BUCK2 { regulator-name = "vdd_arm"; - regulator-min-microvolt = <925000>; - regulator-max-microvolt = <1300000>; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1350000>; regulator-always-on; regulator-boot-on; op_mode = <1>; /* Normal Mode */ diff --git a/arch/arm/boot/dts/exynos4x12.dtsi b/arch/arm/boot/dts/exynos4x12.dtsi index 5c412aa14738..e0eb6bb64c34 100644 --- a/arch/arm/boot/dts/exynos4x12.dtsi +++ b/arch/arm/boot/dts/exynos4x12.dtsi @@ -47,7 +47,7 @@ reg = <0x10050000 0x800>; interrupt-parent = <&mct_map>; interrupts = <0>, <1>, <2>, <3>, <4>; - clocks = <&clock 3>, <&clock 344>; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>; clock-names = "fin_pll", "mct"; mct_map: mct-map { @@ -97,13 +97,14 @@ compatible = "samsung,exynos4212-g2d"; reg = <0x10800000 0x1000>; interrupts = <0 89 0>; - clocks = <&clock 177>, <&clock 277>; + clocks = <&clock CLK_SCLK_FIMG2D>, <&clock CLK_G2D>; clock-names = "sclk_fimg2d", "fimg2d"; status = "disabled"; }; camera { - clocks = <&clock 132>, <&clock 133>, <&clock 351>, <&clock 352>; + clocks = <&clock CLK_SCLK_CAM0>, <&clock CLK_SCLK_CAM1>, + <&clock CLK_PIXELASYNCM0>, <&clock CLK_PIXELASYNCM1>; clock-names = "sclk_cam0", "sclk_cam1", "pxl_async0", "pxl_async1"; fimc_0: fimc@11800000 { @@ -145,7 +146,7 @@ reg = <0x12390000 0x1000>; interrupts = <0 105 0>; samsung,power-domain = <&pd_isp>; - clocks = <&clock 353>; + clocks = <&clock CLK_FIMC_LITE0>; clock-names = "flite"; status = "disabled"; }; @@ -155,7 +156,7 @@ reg = <0x123A0000 0x1000>; interrupts = <0 106 0>; samsung,power-domain = <&pd_isp>; - clocks = <&clock 354>; + clocks = <&clock CLK_FIMC_LITE1>; clock-names = "flite"; status = "disabled"; }; @@ -165,12 +166,19 @@ reg = <0x12000000 0x260000>; interrupts = <0 90 0>, <0 95 0>; samsung,power-domain = <&pd_isp>; - clocks = <&clock 353>, <&clock 354>, <&clock 355>, - <&clock 356>, <&clock 17>, <&clock 357>, - <&clock 358>, <&clock 359>, <&clock 360>, - <&clock 450>,<&clock 451>, <&clock 452>, - <&clock 453>, <&clock 176>, <&clock 13>, - <&clock 454>, <&clock 395>, <&clock 455>; + clocks = <&clock CLK_FIMC_LITE0>, + <&clock CLK_FIMC_LITE1>, <&clock CLK_PPMUISPX>, + <&clock CLK_PPMUISPMX>, + <&clock CLK_MOUT_MPLL_USER_T>, + <&clock CLK_FIMC_ISP>, <&clock CLK_FIMC_DRC>, + <&clock CLK_FIMC_FD>, <&clock CLK_MCUISP>, + <&clock CLK_DIV_ISP0>,<&clock CLK_DIV_ISP1>, + <&clock CLK_DIV_MCUISP0>, + <&clock CLK_DIV_MCUISP1>, + <&clock CLK_SCLK_UART_ISP>, + <&clock CLK_ACLK200>, <&clock CLK_DIV_ACLK200>, + <&clock CLK_ACLK400_MCUISP>, + <&clock CLK_DIV_ACLK400_MCUISP>; clock-names = "lite0", "lite1", "ppmuispx", "ppmuispmx", "mpll", "isp", "drc", "fd", "mcuisp", @@ -190,7 +198,7 @@ i2c1_isp: i2c-isp@12140000 { compatible = "samsung,exynos4212-i2c-isp"; reg = <0x12140000 0x100>; - clocks = <&clock 370>; + clocks = <&clock CLK_I2C1_ISP>; clock-names = "i2c_isp"; #address-cells = <1>; #size-cells = <0>; @@ -205,7 +213,7 @@ #address-cells = <1>; #size-cells = <0>; fifo-depth = <0x80>; - clocks = <&clock 301>, <&clock 149>; + clocks = <&clock CLK_SDMMC4>, <&clock CLK_SCLK_MMC4>; clock-names = "biu", "ciu"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/exynos5.dtsi b/arch/arm/boot/dts/exynos5.dtsi index 258dca441f36..79d0608d6dcc 100644 --- a/arch/arm/boot/dts/exynos5.dtsi +++ b/arch/arm/boot/dts/exynos5.dtsi @@ -81,13 +81,6 @@ status = "disabled"; }; - watchdog { - compatible = "samsung,s3c2410-wdt"; - reg = <0x101D0000 0x100>; - interrupts = <0 42 0>; - status = "disabled"; - }; - fimd@14400000 { compatible = "samsung,exynos5250-fimd"; interrupt-parent = <&combiner>; diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts index 457112d659ea..38b96a4cba6d 100644 --- a/arch/arm/boot/dts/exynos5250-arndale.dts +++ b/arch/arm/boot/dts/exynos5250-arndale.dts @@ -25,6 +25,10 @@ bootargs = "console=ttySAC2,115200"; }; + rtc@101E0000 { + status = "okay"; + }; + codec@11000000 { samsung,mfc-r = <0x43000000 0x800000>; samsung,mfc-l = <0x51000000 0x800000>; diff --git a/arch/arm/boot/dts/exynos5250-smdk5250.dts b/arch/arm/boot/dts/exynos5250-smdk5250.dts index 3e69837c435c..f76946e97e6a 100644 --- a/arch/arm/boot/dts/exynos5250-smdk5250.dts +++ b/arch/arm/boot/dts/exynos5250-smdk5250.dts @@ -27,6 +27,10 @@ bootargs = "root=/dev/ram0 rw ramdisk=8192 initrd=0x41000000,8M console=ttySAC2,115200 init=/linuxrc"; }; + rtc@101E0000 { + status = "okay"; + }; + i2c@12C60000 { samsung,i2c-sda-delay = <100>; samsung,i2c-max-bus-freq = <20000>; @@ -36,6 +40,148 @@ compatible = "samsung,s524ad0xd1"; reg = <0x50>; }; + + max77686@09 { + compatible = "maxim,max77686"; + reg = <0x09>; + + voltage-regulators { + ldo1_reg: LDO1 { + regulator-name = "P1.0V_LDO_OUT1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "P1.2V_LDO_OUT2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "P1.8V_LDO_OUT3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo4_reg: LDO4 { + regulator-name = "P2.8V_LDO_OUT4"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo5_reg: LDO5 { + regulator-name = "P1.8V_LDO_OUT5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo6_reg: LDO6 { + regulator-name = "P1.1V_LDO_OUT6"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + ldo7_reg: LDO7 { + regulator-name = "P1.1V_LDO_OUT7"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + ldo8_reg: LDO8 { + regulator-name = "P1.0V_LDO_OUT8"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo10_reg: LDO10 { + regulator-name = "P1.8V_LDO_OUT10"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo11_reg: LDO11 { + regulator-name = "P1.8V_LDO_OUT11"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo12_reg: LDO12 { + regulator-name = "P3.0V_LDO_OUT12"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ldo13_reg: LDO13 { + regulator-name = "P1.8V_LDO_OUT13"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo14_reg: LDO14 { + regulator-name = "P1.8V_LDO_OUT14"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo15_reg: LDO15 { + regulator-name = "P1.0V_LDO_OUT15"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo16_reg: LDO16 { + regulator-name = "P1.8V_LDO_OUT16"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + }; + + buck3_reg: BUCK3 { + regulator-name = "vdd_int"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "vdd_g3d"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck5_reg: BUCK5 { + regulator-name = "P1.8V_BUCK_OUT5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; }; vdd: fixed-regulator@0 { diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts index 7e45eea2d78f..b13bf499f5e2 100644 --- a/arch/arm/boot/dts/exynos5250-snow.dts +++ b/arch/arm/boot/dts/exynos5250-snow.dts @@ -20,6 +20,10 @@ i2c104 = &i2c_104; }; + rtc@101E0000 { + status = "okay"; + }; + pinctrl@11400000 { sd3_clk: sd3-clk { samsung,pin-drv = <0>; diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi index b7dec41e32af..987cfbe9634b 100644 --- a/arch/arm/boot/dts/exynos5250.dtsi +++ b/arch/arm/boot/dts/exynos5250.dtsi @@ -17,6 +17,7 @@ * published by the Free Software Foundation. */ +#include <dt-bindings/clock/exynos5250.h> #include "exynos5.dtsi" #include "exynos5250-pinctrl.dtsi" @@ -90,7 +91,8 @@ compatible = "samsung,exynos5250-audss-clock"; reg = <0x03810000 0x0C>; #clock-cells = <1>; - clocks = <&clock 1>, <&clock 7>, <&clock 138>, <&clock 160>; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_FOUT_EPLL>, + <&clock CLK_SCLK_AUDIO0>, <&clock CLK_DIV_PCM0>; clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in"; }; @@ -115,7 +117,7 @@ interrupt-parent = <&mct_map>; interrupts = <0 0>, <1 0>, <2 0>, <3 0>, <4 0>, <5 0>; - clocks = <&clock 1>, <&clock 335>; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>; clock-names = "fin_pll", "mct"; mct_map: mct-map { @@ -167,16 +169,25 @@ interrupts = <0 47 0>; }; - watchdog { - clocks = <&clock 336>; + pmu_system_controller: system-controller@10040000 { + compatible = "samsung,exynos5250-pmu", "syscon"; + reg = <0x10040000 0x5000>; + }; + + watchdog@101D0000 { + compatible = "samsung,exynos5250-wdt"; + reg = <0x101D0000 0x100>; + interrupts = <0 42 0>; + clocks = <&clock CLK_WDT>; clock-names = "watchdog"; + samsung,syscon-phandle = <&pmu_system_controller>; }; g2d@10850000 { compatible = "samsung,exynos5250-g2d"; reg = <0x10850000 0x1000>; interrupts = <0 91 0>; - clocks = <&clock 345>; + clocks = <&clock CLK_G2D>; clock-names = "fimg2d"; }; @@ -185,41 +196,41 @@ reg = <0x11000000 0x10000>; interrupts = <0 96 0>; samsung,power-domain = <&pd_mfc>; - clocks = <&clock 266>; + clocks = <&clock CLK_MFC>; clock-names = "mfc"; }; rtc@101E0000 { - clocks = <&clock 337>; + clocks = <&clock CLK_RTC>; clock-names = "rtc"; - status = "okay"; + status = "disabled"; }; tmu@10060000 { compatible = "samsung,exynos5250-tmu"; reg = <0x10060000 0x100>; interrupts = <0 65 0>; - clocks = <&clock 338>; + clocks = <&clock CLK_TMU>; clock-names = "tmu_apbif"; }; serial@12C00000 { - clocks = <&clock 289>, <&clock 146>; + clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>; clock-names = "uart", "clk_uart_baud0"; }; serial@12C10000 { - clocks = <&clock 290>, <&clock 147>; + clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>; clock-names = "uart", "clk_uart_baud0"; }; serial@12C20000 { - clocks = <&clock 291>, <&clock 148>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; }; serial@12C30000 { - clocks = <&clock 292>, <&clock 149>; + clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>; clock-names = "uart", "clk_uart_baud0"; }; @@ -227,7 +238,7 @@ compatible = "samsung,exynos5-sata-ahci"; reg = <0x122F0000 0x1ff>; interrupts = <0 115 0>; - clocks = <&clock 277>, <&clock 143>; + clocks = <&clock CLK_SATA>, <&clock CLK_SCLK_SATA>; clock-names = "sata", "sclk_sata"; }; @@ -242,7 +253,7 @@ interrupts = <0 56 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 294>; + clocks = <&clock CLK_I2C0>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c0_bus>; @@ -255,7 +266,7 @@ interrupts = <0 57 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 295>; + clocks = <&clock CLK_I2C1>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c1_bus>; @@ -268,7 +279,7 @@ interrupts = <0 58 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 296>; + clocks = <&clock CLK_I2C2>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c2_bus>; @@ -281,7 +292,7 @@ interrupts = <0 59 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 297>; + clocks = <&clock CLK_I2C3>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c3_bus>; @@ -294,7 +305,7 @@ interrupts = <0 60 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 298>; + clocks = <&clock CLK_I2C4>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c4_bus>; @@ -307,7 +318,7 @@ interrupts = <0 61 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 299>; + clocks = <&clock CLK_I2C5>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c5_bus>; @@ -320,7 +331,7 @@ interrupts = <0 62 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 300>; + clocks = <&clock CLK_I2C6>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c6_bus>; @@ -333,7 +344,7 @@ interrupts = <0 63 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 301>; + clocks = <&clock CLK_I2C7>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c7_bus>; @@ -346,7 +357,7 @@ interrupts = <0 64 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 302>; + clocks = <&clock CLK_I2C_HDMI>; clock-names = "i2c"; status = "disabled"; }; @@ -356,7 +367,7 @@ reg = <0x121D0000 0x100>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 288>; + clocks = <&clock CLK_SATA_PHYI2C>; clock-names = "i2c"; status = "disabled"; }; @@ -371,7 +382,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 304>, <&clock 154>; + clocks = <&clock CLK_SPI0>, <&clock CLK_SCLK_SPI0>; clock-names = "spi", "spi_busclk0"; pinctrl-names = "default"; pinctrl-0 = <&spi0_bus>; @@ -387,7 +398,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 305>, <&clock 155>; + clocks = <&clock CLK_SPI1>, <&clock CLK_SCLK_SPI1>; clock-names = "spi", "spi_busclk0"; pinctrl-names = "default"; pinctrl-0 = <&spi1_bus>; @@ -403,7 +414,7 @@ dma-names = "tx", "rx"; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 306>, <&clock 156>; + clocks = <&clock CLK_SPI2>, <&clock CLK_SCLK_SPI2>; clock-names = "spi", "spi_busclk0"; pinctrl-names = "default"; pinctrl-0 = <&spi2_bus>; @@ -415,7 +426,7 @@ #address-cells = <1>; #size-cells = <0>; reg = <0x12200000 0x1000>; - clocks = <&clock 280>, <&clock 139>; + clocks = <&clock CLK_SDMMC0>, <&clock CLK_SCLK_MMC0>; clock-names = "biu", "ciu"; fifo-depth = <0x80>; status = "disabled"; @@ -427,7 +438,7 @@ #address-cells = <1>; #size-cells = <0>; reg = <0x12210000 0x1000>; - clocks = <&clock 281>, <&clock 140>; + clocks = <&clock CLK_SDMMC1>, <&clock CLK_SCLK_MMC1>; clock-names = "biu", "ciu"; fifo-depth = <0x80>; status = "disabled"; @@ -439,7 +450,7 @@ #address-cells = <1>; #size-cells = <0>; reg = <0x12220000 0x1000>; - clocks = <&clock 282>, <&clock 141>; + clocks = <&clock CLK_SDMMC2>, <&clock CLK_SCLK_MMC2>; clock-names = "biu", "ciu"; fifo-depth = <0x80>; status = "disabled"; @@ -451,7 +462,7 @@ interrupts = <0 78 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 283>, <&clock 142>; + clocks = <&clock CLK_SDMMC3>, <&clock CLK_SCLK_MMC3>; clock-names = "biu", "ciu"; fifo-depth = <0x80>; status = "disabled"; @@ -481,7 +492,7 @@ dmas = <&pdma1 12 &pdma1 11>; dma-names = "tx", "rx"; - clocks = <&clock 307>, <&clock 157>; + clocks = <&clock CLK_I2S1>, <&clock CLK_DIV_I2S1>; clock-names = "iis", "i2s_opclk0"; pinctrl-names = "default"; pinctrl-0 = <&i2s1_bus>; @@ -494,7 +505,7 @@ dmas = <&pdma0 12 &pdma0 11>; dma-names = "tx", "rx"; - clocks = <&clock 308>, <&clock 158>; + clocks = <&clock CLK_I2S2>, <&clock CLK_DIV_I2S2>; clock-names = "iis", "i2s_opclk0"; pinctrl-names = "default"; pinctrl-0 = <&i2s2_bus>; @@ -502,7 +513,7 @@ usb@12000000 { compatible = "samsung,exynos5250-dwusb3"; - clocks = <&clock 286>; + clocks = <&clock CLK_USB3>; clock-names = "usbdrd30"; #address-cells = <1>; #size-cells = <1>; @@ -519,7 +530,7 @@ usb3_phy: usbphy@12100000 { compatible = "samsung,exynos5250-usb3phy"; reg = <0x12100000 0x100>; - clocks = <&clock 1>, <&clock 286>; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_USB3>; clock-names = "ext_xtal", "usbdrd30"; #address-cells = <1>; #size-cells = <1>; @@ -535,7 +546,7 @@ reg = <0x12110000 0x100>; interrupts = <0 71 0>; - clocks = <&clock 285>; + clocks = <&clock CLK_USB2>; clock-names = "usbhost"; }; @@ -544,14 +555,14 @@ reg = <0x12120000 0x100>; interrupts = <0 71 0>; - clocks = <&clock 285>; + clocks = <&clock CLK_USB2>; clock-names = "usbhost"; }; usb2_phy: usbphy@12130000 { compatible = "samsung,exynos5250-usb2phy"; reg = <0x12130000 0x100>; - clocks = <&clock 1>, <&clock 285>; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_USB2>; clock-names = "ext_xtal", "usbhost"; #address-cells = <1>; #size-cells = <1>; @@ -568,7 +579,7 @@ reg = <0x12dd0000 0x100>; samsung,pwm-outputs = <0>, <1>, <2>, <3>; #pwm-cells = <3>; - clocks = <&clock 311>; + clocks = <&clock CLK_PWM>; clock-names = "timers"; }; @@ -583,7 +594,7 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x121A0000 0x1000>; interrupts = <0 34 0>; - clocks = <&clock 275>; + clocks = <&clock CLK_PDMA0>; clock-names = "apb_pclk"; #dma-cells = <1>; #dma-channels = <8>; @@ -594,7 +605,7 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x121B0000 0x1000>; interrupts = <0 35 0>; - clocks = <&clock 276>; + clocks = <&clock CLK_PDMA1>; clock-names = "apb_pclk"; #dma-cells = <1>; #dma-channels = <8>; @@ -605,7 +616,7 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x10800000 0x1000>; interrupts = <0 33 0>; - clocks = <&clock 346>; + clocks = <&clock CLK_MDMA0>; clock-names = "apb_pclk"; #dma-cells = <1>; #dma-channels = <8>; @@ -616,7 +627,7 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x11C10000 0x1000>; interrupts = <0 124 0>; - clocks = <&clock 271>; + clocks = <&clock CLK_MDMA1>; clock-names = "apb_pclk"; #dma-cells = <1>; #dma-channels = <8>; @@ -629,7 +640,7 @@ reg = <0x13e00000 0x1000>; interrupts = <0 85 0>; samsung,power-domain = <&pd_gsc>; - clocks = <&clock 256>; + clocks = <&clock CLK_GSCL0>; clock-names = "gscl"; }; @@ -638,7 +649,7 @@ reg = <0x13e10000 0x1000>; interrupts = <0 86 0>; samsung,power-domain = <&pd_gsc>; - clocks = <&clock 257>; + clocks = <&clock CLK_GSCL1>; clock-names = "gscl"; }; @@ -647,7 +658,7 @@ reg = <0x13e20000 0x1000>; interrupts = <0 87 0>; samsung,power-domain = <&pd_gsc>; - clocks = <&clock 258>; + clocks = <&clock CLK_GSCL2>; clock-names = "gscl"; }; @@ -656,7 +667,7 @@ reg = <0x13e30000 0x1000>; interrupts = <0 88 0>; samsung,power-domain = <&pd_gsc>; - clocks = <&clock 259>; + clocks = <&clock CLK_GSCL3>; clock-names = "gscl"; }; @@ -664,8 +675,9 @@ compatible = "samsung,exynos4212-hdmi"; reg = <0x14530000 0x70000>; interrupts = <0 95 0>; - clocks = <&clock 344>, <&clock 136>, <&clock 137>, - <&clock 159>, <&clock 1024>; + clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>, + <&clock CLK_SCLK_PIXEL>, <&clock CLK_SCLK_HDMIPHY>, + <&clock CLK_MOUT_HDMI>; clock-names = "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy", "mout_hdmi"; }; @@ -674,7 +686,7 @@ compatible = "samsung,exynos5250-mixer"; reg = <0x14450000 0x10000>; interrupts = <0 94 0>; - clocks = <&clock 343>, <&clock 136>; + clocks = <&clock CLK_MIXER>, <&clock CLK_SCLK_HDMI>; clock-names = "mixer", "sclk_hdmi"; }; @@ -685,14 +697,14 @@ }; dp-controller@145B0000 { - clocks = <&clock 342>; + clocks = <&clock CLK_DP>; clock-names = "dp"; phys = <&dp_phy>; phy-names = "dp"; }; fimd@14400000 { - clocks = <&clock 133>, <&clock 339>; + clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>; clock-names = "sclk_fimd", "fimd"; }; @@ -700,7 +712,7 @@ compatible = "samsung,exynos-adc-v1"; reg = <0x12D10000 0x100>, <0x10040718 0x4>; interrupts = <0 106 0>; - clocks = <&clock 303>; + clocks = <&clock CLK_ADC>; clock-names = "adc"; #io-channel-cells = <1>; io-channel-ranges; diff --git a/arch/arm/boot/dts/exynos5420-arndale-octa.dts b/arch/arm/boot/dts/exynos5420-arndale-octa.dts index 7340745ff979..f509e8fc290f 100644 --- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts +++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts @@ -11,6 +11,8 @@ /dts-v1/; #include "exynos5420.dtsi" +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/input/input.h> / { model = "Insignal Arndale Octa evaluation board based on EXYNOS5420"; @@ -31,6 +33,10 @@ }; }; + rtc@101E0000 { + status = "okay"; + }; + mmc@12200000 { status = "okay"; broken-cd; @@ -41,6 +47,7 @@ samsung,dw-mshc-ddr-timing = <0 2>; pinctrl-names = "default"; pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>; + vmmc-supply = <&ldo10_reg>; slot@0 { reg = <0>; @@ -57,10 +64,301 @@ samsung,dw-mshc-ddr-timing = <1 2>; pinctrl-names = "default"; pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; + vmmc-supply = <&ldo10_reg>; slot@0 { reg = <0>; bus-width = <4>; }; }; + + hsi2c_4: i2c@12CA0000 { + status = "okay"; + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + s2mps11,buck2-ramp-delay = <12>; + s2mps11,buck34-ramp-delay = <12>; + s2mps11,buck16-ramp-delay = <12>; + s2mps11,buck6-ramp-enable = <1>; + s2mps11,buck2-ramp-enable = <1>; + s2mps11,buck3-ramp-enable = <1>; + s2mps11,buck4-ramp-enable = <1>; + + interrupt-parent = <&gpx3>; + interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; + + s2mps11_osc: clocks { + #clock-cells = <1>; + clock-output-names = "s2mps11_ap", + "s2mps11_cp", "s2mps11_bt"; + }; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "PVDD_ALIVE_1V0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo2_reg: LDO2 { + regulator-name = "PVDD_APIO_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo3_reg: LDO3 { + regulator-name = "PVDD_APIO_MMCON_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo4_reg: LDO4 { + regulator-name = "PVDD_ADC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo5_reg: LDO5 { + regulator-name = "PVDD_PLL_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + regulator-name = "PVDD_ANAIP_1V0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + }; + + ldo7_reg: LDO7 { + regulator-name = "PVDD_ANAIP_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo8_reg: LDO8 { + regulator-name = "PVDD_ABB_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo9_reg: LDO9 { + regulator-name = "PVDD_USB_3V3"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ldo10_reg: LDO10 { + regulator-name = "PVDD_PRE_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo11_reg: LDO11 { + regulator-name = "PVDD_USB_1V0"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo12_reg: LDO12 { + regulator-name = "PVDD_HSIC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo13_reg: LDO13 { + regulator-name = "PVDD_APIO_MMCOFF_2V8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo15_reg: LDO15 { + regulator-name = "PVDD_PERI_2V8"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo16_reg: LDO16 { + regulator-name = "PVDD_PERI_3V3"; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + }; + + ldo18_reg: LDO18 { + regulator-name = "PVDD_EMMC_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo19_reg: LDO19 { + regulator-name = "PVDD_TFLASH_2V8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo20_reg: LDO20 { + regulator-name = "PVDD_BTWIFI_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo21_reg: LDO21 { + regulator-name = "PVDD_CAM1IO_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo23_reg: LDO23 { + regulator-name = "PVDD_MIFS_1V1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + ldo24_reg: LDO24 { + regulator-name = "PVDD_CAM1_AVDD_2V8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + ldo26_reg: LDO26 { + regulator-name = "PVDD_CAM0_AF_2V8"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + + ldo27_reg: LDO27 { + regulator-name = "PVDD_G3DS_1V0"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + ldo28_reg: LDO28 { + regulator-name = "PVDD_TSP_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + ldo29_reg: LDO29 { + regulator-name = "PVDD_AUDIO_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo31_reg: LDO31 { + regulator-name = "PVDD_PERI_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo32_reg: LDO32 { + regulator-name = "PVDD_LCD_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo33_reg: LDO33 { + regulator-name = "PVDD_CAM0IO_1V8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + ldo35_reg: LDO35 { + regulator-name = "PVDD_CAM0_DVDD_1V2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + ldo38_reg: LDO38 { + regulator-name = "PVDD_CAM0_AVDD_2V8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + + buck1_reg: BUCK1 { + regulator-name = "PVDD_MIF_1V1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + buck3_reg: BUCK3 { + regulator-name = "PVDD_INT_1V0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "PVDD_G3D_1V0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1000000>; + }; + + buck5_reg: BUCK5 { + regulator-name = "PVDD_LPDDR3_1V2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + }; + + buck6_reg: BUCK6 { + regulator-name = "PVDD_KFC_1V0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + buck7_reg: BUCK7 { + regulator-name = "VIN_LLDO_1V4"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + }; + + buck8_reg: BUCK8 { + regulator-name = "VIN_MLDO_2V0"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + }; + + buck9_reg: BUCK9 { + regulator-name = "VIN_HLDO_3V5"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3500000>; + regulator-always-on; + }; + + buck10_reg: BUCK10 { + regulator-name = "PVDD_EMMCF_2V8"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + }; + }; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + + wakeup { + label = "SW-TACT1"; + gpios = <&gpx2 7 1>; + linux,code = <KEY_WAKEUP>; + gpio-key,wakeup; + }; + }; }; diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts index fb5a1e25c632..ae1ee0470fca 100644 --- a/arch/arm/boot/dts/exynos5420-smdk5420.dts +++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts @@ -31,6 +31,43 @@ }; }; + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + vdd: fixed-regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "vdd-supply"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + dbvdd: fixed-regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "dbvdd-supply"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + spkvdd: fixed-regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "spkvdd-supply"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + }; + + rtc@101E0000 { + status = "okay"; + }; + mmc@12200000 { status = "okay"; broken-cd; @@ -120,4 +157,220 @@ reg = <0x50>; }; }; + + hsi2c_4: i2c@12CA0000 { + status = "okay"; + + s2mps11_pmic@66 { + compatible = "samsung,s2mps11-pmic"; + reg = <0x66>; + s2mps11,buck2-ramp-delay = <12>; + s2mps11,buck34-ramp-delay = <12>; + s2mps11,buck16-ramp-delay = <12>; + s2mps11,buck6-ramp-enable = <1>; + s2mps11,buck2-ramp-enable = <1>; + s2mps11,buck3-ramp-enable = <1>; + s2mps11,buck4-ramp-enable = <1>; + + s2mps11_osc: clocks { + #clock-cells = <1>; + clock-output-names = "s2mps11_ap", + "s2mps11_cp", "s2mps11_bt"; + }; + + regulators { + ldo1_reg: LDO1 { + regulator-name = "vdd_ldo1"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo3_reg: LDO3 { + regulator-name = "vdd_ldo3"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo5_reg: LDO5 { + regulator-name = "vdd_ldo5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo6_reg: LDO6 { + regulator-name = "vdd_ldo6"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo7_reg: LDO7 { + regulator-name = "vdd_ldo7"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo8_reg: LDO8 { + regulator-name = "vdd_ldo8"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo9_reg: LDO9 { + regulator-name = "vdd_ldo9"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + }; + + ldo10_reg: LDO10 { + regulator-name = "vdd_ldo10"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo11_reg: LDO11 { + regulator-name = "vdd_ldo11"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + ldo12_reg: LDO12 { + regulator-name = "vdd_ldo12"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + ldo13_reg: LDO13 { + regulator-name = "vdd_ldo13"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + ldo15_reg: LDO15 { + regulator-name = "vdd_ldo15"; + regulator-min-microvolt = <3100000>; + regulator-max-microvolt = <3100000>; + regulator-always-on; + }; + + ldo16_reg: LDO16 { + regulator-name = "vdd_ldo16"; + regulator-min-microvolt = <2200000>; + regulator-max-microvolt = <2200000>; + regulator-always-on; + }; + + ldo17_reg: LDO17 { + regulator-name = "tsp_avdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + ldo19_reg: LDO19 { + regulator-name = "vdd_sd"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + ldo24_reg: LDO24 { + regulator-name = "tsp_io"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + buck1_reg: BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + }; + + buck2_reg: BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + buck3_reg: BUCK3 { + regulator-name = "vdd_int"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + regulator-boot-on; + }; + + buck4_reg: BUCK4 { + regulator-name = "vdd_g3d"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + regulator-boot-on; + }; + + buck5_reg: BUCK5 { + regulator-name = "vdd_mem"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + regulator-boot-on; + }; + + buck6_reg: BUCK6 { + regulator-name = "vdd_kfc"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + buck7_reg: BUCK7 { + regulator-name = "vdd_1.0v_ldo"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + buck8_reg: BUCK8 { + regulator-name = "vdd_1.8v_ldo"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1500000>; + regulator-always-on; + regulator-boot-on; + }; + + buck9_reg: BUCK9 { + regulator-name = "vdd_2.8v_ldo"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3750000>; + regulator-always-on; + regulator-boot-on; + }; + + buck10_reg: BUCK10 { + regulator-name = "vdd_vmem"; + regulator-min-microvolt = <2850000>; + regulator-max-microvolt = <2850000>; + regulator-always-on; + regulator-boot-on; + }; + }; + }; + }; }; diff --git a/arch/arm/boot/dts/exynos5420.dtsi b/arch/arm/boot/dts/exynos5420.dtsi index 8db792b26f79..e3329afbd8c4 100644 --- a/arch/arm/boot/dts/exynos5420.dtsi +++ b/arch/arm/boot/dts/exynos5420.dtsi @@ -13,6 +13,7 @@ * published by the Free Software Foundation. */ +#include <dt-bindings/clock/exynos5420.h> #include "exynos5.dtsi" #include "exynos5420-pinctrl.dtsi" @@ -119,7 +120,8 @@ compatible = "samsung,exynos5420-audss-clock"; reg = <0x03810000 0x0C>; #clock-cells = <1>; - clocks = <&clock 1>, <&clock 5>, <&clock 148>, <&clock 149>; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_FOUT_EPLL>, + <&clock CLK_SCLK_MAUDIO0>, <&clock CLK_SCLK_MAUPCM0>; clock-names = "pll_ref", "pll_in", "sclk_audio", "sclk_pcm_in"; }; @@ -127,7 +129,7 @@ compatible = "samsung,mfc-v7"; reg = <0x11000000 0x10000>; interrupts = <0 96 0>; - clocks = <&clock 401>; + clocks = <&clock CLK_MFC>; clock-names = "mfc"; }; @@ -137,7 +139,7 @@ #address-cells = <1>; #size-cells = <0>; reg = <0x12200000 0x2000>; - clocks = <&clock 351>, <&clock 132>; + clocks = <&clock CLK_MMC0>, <&clock CLK_SCLK_MMC0>; clock-names = "biu", "ciu"; fifo-depth = <0x40>; status = "disabled"; @@ -149,7 +151,7 @@ #address-cells = <1>; #size-cells = <0>; reg = <0x12210000 0x2000>; - clocks = <&clock 352>, <&clock 133>; + clocks = <&clock CLK_MMC1>, <&clock CLK_SCLK_MMC1>; clock-names = "biu", "ciu"; fifo-depth = <0x40>; status = "disabled"; @@ -161,7 +163,7 @@ #address-cells = <1>; #size-cells = <0>; reg = <0x12220000 0x1000>; - clocks = <&clock 353>, <&clock 134>; + clocks = <&clock CLK_MMC2>, <&clock CLK_SCLK_MMC2>; clock-names = "biu", "ciu"; fifo-depth = <0x40>; status = "disabled"; @@ -175,7 +177,7 @@ interrupt-parent = <&mct_map>; interrupts = <0>, <1>, <2>, <3>, <4>, <5>, <6>, <7>, <8>, <9>, <10>, <11>; - clocks = <&clock 1>, <&clock 315>; + clocks = <&clock CLK_FIN_PLL>, <&clock CLK_MCT>; clock-names = "fin_pll", "mct"; mct_map: mct-map { @@ -269,9 +271,9 @@ }; rtc@101E0000 { - clocks = <&clock 317>; + clocks = <&clock CLK_RTC>; clock-names = "rtc"; - status = "okay"; + status = "disabled"; }; amba { @@ -281,11 +283,22 @@ interrupt-parent = <&gic>; ranges; + adma: adma@03880000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x03880000 0x1000>; + interrupts = <0 110 0>; + clocks = <&clock_audss EXYNOS_ADMA>; + clock-names = "apb_pclk"; + #dma-cells = <1>; + #dma-channels = <6>; + #dma-requests = <16>; + }; + pdma0: pdma@121A0000 { compatible = "arm,pl330", "arm,primecell"; reg = <0x121A0000 0x1000>; interrupts = <0 34 0>; - clocks = <&clock 362>; + clocks = <&clock CLK_PDMA0>; clock-names = "apb_pclk"; #dma-cells = <1>; #dma-channels = <8>; @@ -296,7 +309,7 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x121B0000 0x1000>; interrupts = <0 35 0>; - clocks = <&clock 363>; + clocks = <&clock CLK_PDMA1>; clock-names = "apb_pclk"; #dma-cells = <1>; #dma-channels = <8>; @@ -307,7 +320,7 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x10800000 0x1000>; interrupts = <0 33 0>; - clocks = <&clock 473>; + clocks = <&clock CLK_MDMA0>; clock-names = "apb_pclk"; #dma-cells = <1>; #dma-channels = <8>; @@ -318,7 +331,7 @@ compatible = "arm,pl330", "arm,primecell"; reg = <0x11C10000 0x1000>; interrupts = <0 124 0>; - clocks = <&clock 442>; + clocks = <&clock CLK_MDMA1>; clock-names = "apb_pclk"; #dma-cells = <1>; #dma-channels = <8>; @@ -326,6 +339,49 @@ }; }; + i2s0: i2s@03830000 { + compatible = "samsung,exynos5420-i2s"; + reg = <0x03830000 0x100>; + dmas = <&adma 0 + &adma 2 + &adma 1>; + dma-names = "tx", "rx", "tx-sec"; + clocks = <&clock_audss EXYNOS_I2S_BUS>, + <&clock_audss EXYNOS_I2S_BUS>, + <&clock_audss EXYNOS_SCLK_I2S>; + clock-names = "iis", "i2s_opclk0", "i2s_opclk1"; + samsung,idma-addr = <0x03000000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2s0_bus>; + status = "disabled"; + }; + + i2s1: i2s@12D60000 { + compatible = "samsung,exynos5420-i2s"; + reg = <0x12D60000 0x100>; + dmas = <&pdma1 12 + &pdma1 11>; + dma-names = "tx", "rx"; + clocks = <&clock CLK_I2S1>, <&clock CLK_SCLK_I2S1>; + clock-names = "iis", "i2s_opclk0"; + pinctrl-names = "default"; + pinctrl-0 = <&i2s1_bus>; + status = "disabled"; + }; + + i2s2: i2s@12D70000 { + compatible = "samsung,exynos5420-i2s"; + reg = <0x12D70000 0x100>; + dmas = <&pdma0 12 + &pdma0 11>; + dma-names = "tx", "rx"; + clocks = <&clock CLK_I2S2>, <&clock CLK_SCLK_I2S2>; + clock-names = "iis", "i2s_opclk0"; + pinctrl-names = "default"; + pinctrl-0 = <&i2s2_bus>; + status = "disabled"; + }; + spi_0: spi@12d20000 { compatible = "samsung,exynos4210-spi"; reg = <0x12d20000 0x100>; @@ -337,7 +393,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&spi0_bus>; - clocks = <&clock 271>, <&clock 135>; + clocks = <&clock CLK_SPI0>, <&clock CLK_SCLK_SPI0>; clock-names = "spi", "spi_busclk0"; status = "disabled"; }; @@ -353,7 +409,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&spi1_bus>; - clocks = <&clock 272>, <&clock 136>; + clocks = <&clock CLK_SPI1>, <&clock CLK_SCLK_SPI1>; clock-names = "spi", "spi_busclk0"; status = "disabled"; }; @@ -369,28 +425,28 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&spi2_bus>; - clocks = <&clock 273>, <&clock 137>; + clocks = <&clock CLK_SPI2>, <&clock CLK_SCLK_SPI2>; clock-names = "spi", "spi_busclk0"; status = "disabled"; }; serial@12C00000 { - clocks = <&clock 257>, <&clock 128>; + clocks = <&clock CLK_UART0>, <&clock CLK_SCLK_UART0>; clock-names = "uart", "clk_uart_baud0"; }; serial@12C10000 { - clocks = <&clock 258>, <&clock 129>; + clocks = <&clock CLK_UART1>, <&clock CLK_SCLK_UART1>; clock-names = "uart", "clk_uart_baud0"; }; serial@12C20000 { - clocks = <&clock 259>, <&clock 130>; + clocks = <&clock CLK_UART2>, <&clock CLK_SCLK_UART2>; clock-names = "uart", "clk_uart_baud0"; }; serial@12C30000 { - clocks = <&clock 260>, <&clock 131>; + clocks = <&clock CLK_UART3>, <&clock CLK_SCLK_UART3>; clock-names = "uart", "clk_uart_baud0"; }; @@ -399,7 +455,7 @@ reg = <0x12dd0000 0x100>; samsung,pwm-outputs = <0>, <1>, <2>, <3>; #pwm-cells = <3>; - clocks = <&clock 279>; + clocks = <&clock CLK_PWM>; clock-names = "timers"; }; @@ -410,7 +466,7 @@ }; dp-controller@145B0000 { - clocks = <&clock 412>; + clocks = <&clock CLK_DP1>; clock-names = "dp"; phys = <&dp_phy>; phy-names = "dp"; @@ -418,7 +474,7 @@ fimd@14400000 { samsung,power-domain = <&disp_pd>; - clocks = <&clock 147>, <&clock 421>; + clocks = <&clock CLK_SCLK_FIMD1>, <&clock CLK_FIMD1>; clock-names = "sclk_fimd", "fimd"; }; @@ -426,7 +482,7 @@ compatible = "samsung,exynos-adc-v2"; reg = <0x12D10000 0x100>, <0x10040720 0x4>; interrupts = <0 106 0>; - clocks = <&clock 270>; + clocks = <&clock CLK_TSADC>; clock-names = "adc"; #io-channel-cells = <1>; io-channel-ranges; @@ -439,7 +495,7 @@ interrupts = <0 56 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 261>; + clocks = <&clock CLK_I2C0>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c0_bus>; @@ -452,7 +508,7 @@ interrupts = <0 57 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 262>; + clocks = <&clock CLK_I2C1>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c1_bus>; @@ -465,7 +521,7 @@ interrupts = <0 58 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 263>; + clocks = <&clock CLK_I2C2>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c2_bus>; @@ -478,7 +534,7 @@ interrupts = <0 59 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 264>; + clocks = <&clock CLK_I2C3>; clock-names = "i2c"; pinctrl-names = "default"; pinctrl-0 = <&i2c3_bus>; @@ -493,7 +549,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c4_hs_bus>; - clocks = <&clock 265>; + clocks = <&clock CLK_I2C4>; clock-names = "hsi2c"; status = "disabled"; }; @@ -506,7 +562,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c5_hs_bus>; - clocks = <&clock 266>; + clocks = <&clock CLK_I2C5>; clock-names = "hsi2c"; status = "disabled"; }; @@ -519,7 +575,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c6_hs_bus>; - clocks = <&clock 267>; + clocks = <&clock CLK_I2C6>; clock-names = "hsi2c"; status = "disabled"; }; @@ -532,7 +588,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c7_hs_bus>; - clocks = <&clock 268>; + clocks = <&clock CLK_I2C7>; clock-names = "hsi2c"; status = "disabled"; }; @@ -545,7 +601,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c8_hs_bus>; - clocks = <&clock 281>; + clocks = <&clock CLK_I2C8>; clock-names = "hsi2c"; status = "disabled"; }; @@ -558,7 +614,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c9_hs_bus>; - clocks = <&clock 282>; + clocks = <&clock CLK_I2C9>; clock-names = "hsi2c"; status = "disabled"; }; @@ -571,7 +627,7 @@ #size-cells = <0>; pinctrl-names = "default"; pinctrl-0 = <&i2c10_hs_bus>; - clocks = <&clock 283>; + clocks = <&clock CLK_I2C10>; clock-names = "hsi2c"; status = "disabled"; }; @@ -580,8 +636,9 @@ compatible = "samsung,exynos4212-hdmi"; reg = <0x14530000 0x70000>; interrupts = <0 95 0>; - clocks = <&clock 413>, <&clock 143>, <&clock 768>, - <&clock 158>, <&clock 640>; + clocks = <&clock CLK_HDMI>, <&clock CLK_SCLK_HDMI>, + <&clock CLK_DOUT_PIXEL>, <&clock CLK_SCLK_HDMIPHY>, + <&clock CLK_MOUT_HDMI>; clock-names = "hdmi", "sclk_hdmi", "sclk_pixel", "sclk_hdmiphy", "mout_hdmi"; status = "disabled"; @@ -591,7 +648,7 @@ compatible = "samsung,exynos5420-mixer"; reg = <0x14450000 0x10000>; interrupts = <0 94 0>; - clocks = <&clock 431>, <&clock 143>; + clocks = <&clock CLK_MIXER>, <&clock CLK_SCLK_HDMI>; clock-names = "mixer", "sclk_hdmi"; }; @@ -599,7 +656,7 @@ compatible = "samsung,exynos5-gsc"; reg = <0x13e00000 0x1000>; interrupts = <0 85 0>; - clocks = <&clock 465>; + clocks = <&clock CLK_GSCL0>; clock-names = "gscl"; samsung,power-domain = <&gsc_pd>; }; @@ -608,16 +665,21 @@ compatible = "samsung,exynos5-gsc"; reg = <0x13e10000 0x1000>; interrupts = <0 86 0>; - clocks = <&clock 466>; + clocks = <&clock CLK_GSCL1>; clock-names = "gscl"; samsung,power-domain = <&gsc_pd>; }; + pmu_system_controller: system-controller@10040000 { + compatible = "samsung,exynos5420-pmu", "syscon"; + reg = <0x10040000 0x5000>; + }; + tmu_cpu0: tmu@10060000 { compatible = "samsung,exynos5420-tmu"; reg = <0x10060000 0x100>; interrupts = <0 65 0>; - clocks = <&clock 318>; + clocks = <&clock CLK_TMU>; clock-names = "tmu_apbif"; }; @@ -625,7 +687,7 @@ compatible = "samsung,exynos5420-tmu"; reg = <0x10064000 0x100>; interrupts = <0 183 0>; - clocks = <&clock 318>; + clocks = <&clock CLK_TMU>; clock-names = "tmu_apbif"; }; @@ -633,7 +695,7 @@ compatible = "samsung,exynos5420-tmu-ext-triminfo"; reg = <0x10068000 0x100>, <0x1006c000 0x4>; interrupts = <0 184 0>; - clocks = <&clock 318>, <&clock 318>; + clocks = <&clock CLK_TMU>, <&clock CLK_TMU>; clock-names = "tmu_apbif", "tmu_triminfo_apbif"; }; @@ -641,7 +703,7 @@ compatible = "samsung,exynos5420-tmu-ext-triminfo"; reg = <0x1006c000 0x100>, <0x100a0000 0x4>; interrupts = <0 185 0>; - clocks = <&clock 318>, <&clock 319>; + clocks = <&clock CLK_TMU>, <&clock CLK_TMU_GPU>; clock-names = "tmu_apbif", "tmu_triminfo_apbif"; }; @@ -649,7 +711,16 @@ compatible = "samsung,exynos5420-tmu-ext-triminfo"; reg = <0x100a0000 0x100>, <0x10068000 0x4>; interrupts = <0 215 0>; - clocks = <&clock 319>, <&clock 318>; + clocks = <&clock CLK_TMU_GPU>, <&clock CLK_TMU>; clock-names = "tmu_apbif", "tmu_triminfo_apbif"; }; + + watchdog@101D0000 { + compatible = "samsung,exynos5420-wdt"; + reg = <0x101D0000 0x100>; + interrupts = <0 42 0>; + clocks = <&clock CLK_WDT>; + clock-names = "watchdog"; + samsung,syscon-phandle = <&pmu_system_controller>; + }; }; diff --git a/arch/arm/boot/dts/exynos5440.dtsi b/arch/arm/boot/dts/exynos5440.dtsi index 02a0a1226cef..75c7b89cec2f 100644 --- a/arch/arm/boot/dts/exynos5440.dtsi +++ b/arch/arm/boot/dts/exynos5440.dtsi @@ -9,6 +9,7 @@ * published by the Free Software Foundation. */ +#include <dt-bindings/clock/exynos5440.h> #include "skeleton.dtsi" / { @@ -105,7 +106,7 @@ compatible = "samsung,exynos4210-uart"; reg = <0xB0000 0x1000>; interrupts = <0 2 0>; - clocks = <&clock 21>, <&clock 21>; + clocks = <&clock CLK_B_125>, <&clock CLK_B_125>; clock-names = "uart", "clk_uart_baud0"; }; @@ -113,7 +114,7 @@ compatible = "samsung,exynos4210-uart"; reg = <0xC0000 0x1000>; interrupts = <0 3 0>; - clocks = <&clock 21>, <&clock 21>; + clocks = <&clock CLK_B_125>, <&clock CLK_B_125>; clock-names = "uart", "clk_uart_baud0"; }; @@ -125,7 +126,7 @@ #size-cells = <0>; samsung,spi-src-clk = <0>; num-cs = <1>; - clocks = <&clock 21>, <&clock 16>; + clocks = <&clock CLK_B_125>, <&clock CLK_SPI_BAUD>; clock-names = "spi", "spi_busclk0"; }; @@ -161,7 +162,7 @@ interrupts = <0 5 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 21>; + clocks = <&clock CLK_B_125>; clock-names = "i2c"; }; @@ -171,7 +172,7 @@ interrupts = <0 6 0>; #address-cells = <1>; #size-cells = <0>; - clocks = <&clock 21>; + clocks = <&clock CLK_B_125>; clock-names = "i2c"; }; @@ -179,7 +180,7 @@ compatible = "samsung,s3c2410-wdt"; reg = <0x110000 0x1000>; interrupts = <0 1 0>; - clocks = <&clock 21>; + clocks = <&clock CLK_B_125>; clock-names = "watchdog"; }; @@ -190,7 +191,7 @@ interrupts = <0 31 4>; interrupt-names = "macirq"; phy-mode = "sgmii"; - clocks = <&clock 25>; + clocks = <&clock CLK_GMAC0>; clock-names = "stmmaceth"; }; @@ -206,7 +207,7 @@ compatible = "samsung,s3c6410-rtc"; reg = <0x130000 0x1000>; interrupts = <0 17 0>, <0 16 0>; - clocks = <&clock 21>; + clocks = <&clock CLK_B_125>; clock-names = "rtc"; }; @@ -214,7 +215,7 @@ compatible = "samsung,exynos5440-tmu"; reg = <0x160118 0x230>, <0x160368 0x10>; interrupts = <0 58 0>; - clocks = <&clock 21>; + clocks = <&clock CLK_B_125>; clock-names = "tmu_apbif"; }; @@ -222,7 +223,7 @@ compatible = "samsung,exynos5440-tmu"; reg = <0x16011C 0x230>, <0x160368 0x10>; interrupts = <0 58 0>; - clocks = <&clock 21>; + clocks = <&clock CLK_B_125>; clock-names = "tmu_apbif"; }; @@ -230,7 +231,7 @@ compatible = "samsung,exynos5440-tmu"; reg = <0x160120 0x230>, <0x160368 0x10>; interrupts = <0 58 0>; - clocks = <&clock 21>; + clocks = <&clock CLK_B_125>; clock-names = "tmu_apbif"; }; @@ -238,7 +239,7 @@ compatible = "snps,exynos5440-ahci"; reg = <0x210000 0x10000>; interrupts = <0 30 0>; - clocks = <&clock 23>; + clocks = <&clock CLK_SATA>; clock-names = "sata"; }; @@ -246,7 +247,7 @@ compatible = "samsung,exynos5440-ohci"; reg = <0x220000 0x1000>; interrupts = <0 29 0>; - clocks = <&clock 24>; + clocks = <&clock CLK_USB>; clock-names = "usbhost"; }; @@ -254,7 +255,7 @@ compatible = "samsung,exynos5440-ehci"; reg = <0x221000 0x1000>; interrupts = <0 29 0>; - clocks = <&clock 24>; + clocks = <&clock CLK_USB>; clock-names = "usbhost"; }; @@ -264,7 +265,7 @@ 0x270000 0x1000 0x271000 0x40>; interrupts = <0 20 0>, <0 21 0>, <0 22 0>; - clocks = <&clock 28>, <&clock 27>; + clocks = <&clock CLK_PR0_250_O>, <&clock CLK_PB0_250_O>; clock-names = "pcie", "pcie_bus"; #address-cells = <3>; #size-cells = <2>; @@ -285,7 +286,7 @@ 0x272000 0x1000 0x271040 0x40>; interrupts = <0 23 0>, <0 24 0>, <0 25 0>; - clocks = <&clock 29>, <&clock 27>; + clocks = <&clock CLK_PR1_250_O>, <&clock CLK_PB0_250_O>; clock-names = "pcie", "pcie_bus"; #address-cells = <3>; #size-cells = <2>; diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/imx23-evk.dts index 1f026adefd45..a33f66c11b73 100644 --- a/arch/arm/boot/dts/imx23-evk.dts +++ b/arch/arm/boot/dts/imx23-evk.dts @@ -127,17 +127,21 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_vddio_sd0: vddio-sd0 { + reg_vddio_sd0: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "vddio-sd0"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; gpio = <&gpio1 29 0>; }; - reg_lcd_3v3: lcd-3v3 { + reg_lcd_3v3: regulator@1 { compatible = "regulator-fixed"; + reg = <1>; regulator-name = "lcd-3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; diff --git a/arch/arm/boot/dts/imx23-olinuxino.dts b/arch/arm/boot/dts/imx23-olinuxino.dts index 526bfdbd87f9..7e6eef2488e8 100644 --- a/arch/arm/boot/dts/imx23-olinuxino.dts +++ b/arch/arm/boot/dts/imx23-olinuxino.dts @@ -100,9 +100,12 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_usb0_vbus: usb0_vbus { + reg_usb0_vbus: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "usb0_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; diff --git a/arch/arm/boot/dts/imx23-stmp378x_devb.dts b/arch/arm/boot/dts/imx23-stmp378x_devb.dts index cb64e2b191ea..455169e99d49 100644 --- a/arch/arm/boot/dts/imx23-stmp378x_devb.dts +++ b/arch/arm/boot/dts/imx23-stmp378x_devb.dts @@ -66,9 +66,12 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_vddio_sd0: vddio-sd0 { + reg_vddio_sd0: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "vddio-sd0"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; diff --git a/arch/arm/boot/dts/imx23.dtsi b/arch/arm/boot/dts/imx23.dtsi index 581b75433be6..bbcfb5a19c77 100644 --- a/arch/arm/boot/dts/imx23.dtsi +++ b/arch/arm/boot/dts/imx23.dtsi @@ -23,6 +23,7 @@ serial1 = &auart1; spi0 = &ssp0; spi1 = &ssp1; + usbphy0 = &usbphy0; }; cpus { @@ -428,7 +429,7 @@ status = "disabled"; }; - lradc@80050000 { + lradc: lradc@80050000 { compatible = "fsl,imx23-lradc"; reg = <0x80050000 0x2000>; interrupts = <36 37 38 39 40 41 42 43 44>; @@ -526,4 +527,9 @@ status = "disabled"; }; }; + + iio_hwmon { + compatible = "iio-hwmon"; + io-channels = <&lradc 8>; + }; }; diff --git a/arch/arm/boot/dts/imx25-eukrea-cpuimx25.dtsi b/arch/arm/boot/dts/imx25-eukrea-cpuimx25.dtsi new file mode 100644 index 000000000000..d6f27641c0ef --- /dev/null +++ b/arch/arm/boot/dts/imx25-eukrea-cpuimx25.dtsi @@ -0,0 +1,73 @@ +/* + * Copyright 2013 Eukréa Electromatique <denis@eukrea.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include "imx25.dtsi" + +/ { + model = "Eukrea CPUIMX25"; + compatible = "eukrea,cpuimx25", "fsl,imx25"; + + memory { + reg = <0x80000000 0x4000000>; /* 64M */ + }; +}; + +&fec { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pcf8563@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +&iomuxc { + imx25-eukrea-cpuimx25 { + pinctrl_fec: fecgrp { + fsl,pins = < + MX25_PAD_FEC_MDC__FEC_MDC 0x80000000 + MX25_PAD_FEC_MDIO__FEC_MDIO 0x400001e0 + MX25_PAD_FEC_TDATA0__FEC_TDATA0 0x80000000 + MX25_PAD_FEC_TDATA1__FEC_TDATA1 0x80000000 + MX25_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000 + MX25_PAD_FEC_RDATA0__FEC_RDATA0 0x80000000 + MX25_PAD_FEC_RDATA1__FEC_RDATA1 0x80000000 + MX25_PAD_FEC_RX_DV__FEC_RX_DV 0x80000000 + MX25_PAD_FEC_TX_CLK__FEC_TX_CLK 0x1c0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX25_PAD_I2C1_CLK__I2C1_CLK 0x80000000 + MX25_PAD_I2C1_DAT__I2C1_DAT 0x80000000 + >; + }; + }; +}; + +&nfc { + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dts b/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dts new file mode 100644 index 000000000000..62fb3da50bdb --- /dev/null +++ b/arch/arm/boot/dts/imx25-eukrea-mbimxsd25-baseboard.dts @@ -0,0 +1,174 @@ +/* + * Copyright 2013 Eukréa Electromatique <denis@eukrea.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include "imx25-eukrea-cpuimx25.dtsi" + +/ { + model = "Eukrea MBIMXSD25"; + compatible = "eukrea,mbimxsd25-baseboard", "eukrea,cpuimx25", "fsl,imx25"; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpiokeys>; + + bp1 { + label = "BP1"; + gpios = <&gpio3 18 GPIO_ACTIVE_LOW>; + linux,code = <BTN_MISC>; + gpio-key,wakeup; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpioled>; + + led1 { + label = "led1"; + gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; + + sound { + compatible = "eukrea,asoc-tlv320"; + eukrea,model = "imx25-eukrea-tlv320aic23"; + ssi-controller = <&ssi1>; + fsl,mux-int-port = <1>; + fsl,mux-ext-port = <5>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&esdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc1>; + cd-gpios = <&gpio1 20>; + status = "okay"; +}; + +&i2c1 { + tlv320aic23: codec@1a { + compatible = "ti,tlv320aic23"; + reg = <0x1a>; + }; +}; + +&iomuxc { + imx25-eukrea-mbimxsd25-baseboard { + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX25_PAD_KPP_COL3__AUD5_TXFS 0xe0 + MX25_PAD_KPP_COL2__AUD5_TXC 0xe0 + MX25_PAD_KPP_COL1__AUD5_RXD 0xe0 + MX25_PAD_KPP_COL0__AUD5_TXD 0xe0 + >; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + MX25_PAD_SD1_CMD__SD1_CMD 0x400000c0 + MX25_PAD_SD1_CLK__SD1_CLK 0x400000c0 + MX25_PAD_SD1_DATA0__SD1_DATA0 0x400000c0 + MX25_PAD_SD1_DATA1__SD1_DATA1 0x400000c0 + MX25_PAD_SD1_DATA2__SD1_DATA2 0x400000c0 + MX25_PAD_SD1_DATA3__SD1_DATA3 0x400000c0 + >; + }; + + pinctrl_gpiokeys: gpiokeysgrp { + fsl,pins = <MX25_PAD_VSTBY_ACK__GPIO_3_18 0x80000000>; + }; + + pinctrl_gpioled: gpioledgrp { + fsl,pins = <MX25_PAD_POWER_FAIL__GPIO_3_19 0x80000000>; + }; + + pinctrl_lcdc: lcdcgrp { + fsl,pins = < + MX25_PAD_LD0__LD0 0x1 + MX25_PAD_LD1__LD1 0x1 + MX25_PAD_LD2__LD2 0x1 + MX25_PAD_LD3__LD3 0x1 + MX25_PAD_LD4__LD4 0x1 + MX25_PAD_LD5__LD5 0x1 + MX25_PAD_LD6__LD6 0x1 + MX25_PAD_LD7__LD7 0x1 + MX25_PAD_LD8__LD8 0x1 + MX25_PAD_LD9__LD9 0x1 + MX25_PAD_LD10__LD10 0x1 + MX25_PAD_LD11__LD11 0x1 + MX25_PAD_LD12__LD12 0x1 + MX25_PAD_LD13__LD13 0x1 + MX25_PAD_LD14__LD14 0x1 + MX25_PAD_LD15__LD15 0x1 + MX25_PAD_GPIO_E__LD16 0x1 + MX25_PAD_GPIO_F__LD17 0x1 + MX25_PAD_HSYNC__HSYNC 0x80000000 + MX25_PAD_VSYNC__VSYNC 0x80000000 + MX25_PAD_LSCLK__LSCLK 0x80000000 + MX25_PAD_OE_ACD__OE_ACD 0x80000000 + MX25_PAD_CONTRAST__CONTRAST 0x80000000 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX25_PAD_UART1_RTS__UART1_RTS 0xe0 + MX25_PAD_UART1_CTS__UART1_CTS 0xe0 + MX25_PAD_UART1_TXD__UART1_TXD 0x80000000 + MX25_PAD_UART1_RXD__UART1_RXD 0xc0 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX25_PAD_UART2_RXD__UART2_RXD 0x80000000 + MX25_PAD_UART2_TXD__UART2_TXD 0x80000000 + MX25_PAD_UART2_RTS__UART2_RTS 0x80000000 + MX25_PAD_UART2_CTS__UART2_CTS 0x80000000 + >; + }; + }; +}; + +&ssi1 { + codec-handle = <&tlv320aic23>; + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + fsl,uart-has-rtscts; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx25-pinfunc.h b/arch/arm/boot/dts/imx25-pinfunc.h new file mode 100644 index 000000000000..9238a95d8e62 --- /dev/null +++ b/arch/arm/boot/dts/imx25-pinfunc.h @@ -0,0 +1,494 @@ +/* + * Copyright 2013 Eukréa Electromatique <denis@eukrea.com> + * Based on imx35-pinfunc.h in the same directory Which is: + * Copyright 2013 Freescale Semiconductor, Inc. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef __DTS_IMX25_PINFUNC_H +#define __DTS_IMX25_PINFUNC_H + +/* + * The pin function ID is a tuple of + * <mux_reg conf_reg input_reg mux_mode input_val> + */ + +#define MX25_PAD_A10__A10 0x008 0x000 0x000 0x00 0x000 +#define MX25_PAD_A10__GPIO_4_0 0x008 0x000 0x000 0x05 0x000 + +#define MX25_PAD_A13__A13 0x00c 0x22C 0x000 0x00 0x000 +#define MX25_PAD_A13__GPIO_4_1 0x00c 0x22C 0x000 0x05 0x000 + +#define MX25_PAD_A14__A14 0x010 0x230 0x000 0x10 0x000 +#define MX25_PAD_A14__GPIO_2_0 0x010 0x230 0x000 0x15 0x000 + +#define MX25_PAD_A15__A15 0x014 0x234 0x000 0x10 0x000 +#define MX25_PAD_A15__GPIO_2_1 0x014 0x234 0x000 0x15 0x000 + +#define MX25_PAD_A16__A16 0x018 0x000 0x000 0x10 0x000 +#define MX25_PAD_A16__GPIO_2_2 0x018 0x000 0x000 0x15 0x000 + +#define MX25_PAD_A17__A17 0x01c 0x238 0x000 0x10 0x000 +#define MX25_PAD_A17__GPIO_2_3 0x01c 0x238 0x000 0x15 0x000 + +#define MX25_PAD_A18__A18 0x020 0x23c 0x000 0x10 0x000 +#define MX25_PAD_A18__GPIO_2_4 0x020 0x23c 0x000 0x15 0x000 +#define MX25_PAD_A18__FEC_COL 0x020 0x23c 0x504 0x17 0x000 + +#define MX25_PAD_A19__A19 0x024 0x240 0x000 0x10 0x000 +#define MX25_PAD_A19__FEC_RX_ER 0x024 0x240 0x518 0x17 0x000 +#define MX25_PAD_A19__GPIO_2_5 0x024 0x240 0x000 0x15 0x000 + +#define MX25_PAD_A20__A20 0x028 0x244 0x000 0x10 0x000 +#define MX25_PAD_A20__GPIO_2_6 0x028 0x244 0x000 0x15 0x000 +#define MX25_PAD_A20__FEC_RDATA2 0x028 0x244 0x50c 0x17 0x000 + +#define MX25_PAD_A21__A21 0x02c 0x248 0x000 0x10 0x000 +#define MX25_PAD_A21__GPIO_2_7 0x02c 0x248 0x000 0x15 0x000 +#define MX25_PAD_A21__FEC_RDATA3 0x02c 0x248 0x510 0x17 0x000 + +#define MX25_PAD_A22__A22 0x030 0x000 0x000 0x10 0x000 +#define MX25_PAD_A22__GPIO_2_8 0x030 0x000 0x000 0x15 0x000 + +#define MX25_PAD_A23__A23 0x034 0x24c 0x000 0x10 0x000 +#define MX25_PAD_A23__GPIO_2_9 0x034 0x24c 0x000 0x15 0x000 + +#define MX25_PAD_A24__A24 0x038 0x250 0x000 0x10 0x000 +#define MX25_PAD_A24__GPIO_2_10 0x038 0x250 0x000 0x15 0x000 +#define MX25_PAD_A24__FEC_RX_CLK 0x038 0x250 0x514 0x17 0x000 + +#define MX25_PAD_A25__A25 0x03c 0x254 0x000 0x10 0x000 +#define MX25_PAD_A25__GPIO_2_11 0x03c 0x254 0x000 0x15 0x000 +#define MX25_PAD_A25__FEC_CRS 0x03c 0x254 0x508 0x17 0x000 + +#define MX25_PAD_EB0__EB0 0x040 0x258 0x000 0x10 0x000 +#define MX25_PAD_EB0__AUD4_TXD 0x040 0x258 0x464 0x14 0x000 +#define MX25_PAD_EB0__GPIO_2_12 0x040 0x258 0x000 0x15 0x000 + +#define MX25_PAD_EB1__EB1 0x044 0x25c 0x000 0x10 0x000 +#define MX25_PAD_EB1__AUD4_RXD 0x044 0x25c 0x460 0x14 0x000 +#define MX25_PAD_EB1__GPIO_2_13 0x044 0x25c 0x000 0x15 0x000 + +#define MX25_PAD_OE__OE 0x048 0x260 0x000 0x10 0x000 +#define MX25_PAD_OE__AUD4_TXC 0x048 0x260 0x000 0x14 0x000 +#define MX25_PAD_OE__GPIO_2_14 0x048 0x260 0x000 0x15 0x000 + +#define MX25_PAD_CS0__CS0 0x04c 0x000 0x000 0x00 0x000 +#define MX25_PAD_CS0__GPIO_4_2 0x04c 0x000 0x000 0x05 0x000 + +#define MX25_PAD_CS1__CS1 0x050 0x000 0x000 0x00 0x000 +#define MX25_PAD_CS1__NF_CE3 0x050 0x000 0x000 0x01 0x000 +#define MX25_PAD_CS1__GPIO_4_3 0x050 0x000 0x000 0x05 0x000 + +#define MX25_PAD_CS4__CS4 0x054 0x264 0x000 0x10 0x000 +#define MX25_PAD_CS4__NF_CE1 0x054 0x264 0x000 0x01 0x000 +#define MX25_PAD_CS4__UART5_CTS 0x054 0x264 0x000 0x13 0x000 +#define MX25_PAD_CS4__GPIO_3_20 0x054 0x264 0x000 0x15 0x000 + +#define MX25_PAD_CS5__CS5 0x058 0x268 0x000 0x10 0x000 +#define MX25_PAD_CS5__NF_CE2 0x058 0x268 0x000 0x01 0x000 +#define MX25_PAD_CS5__UART5_RTS 0x058 0x268 0x574 0x13 0x000 +#define MX25_PAD_CS5__GPIO_3_21 0x058 0x268 0x000 0x15 0x000 + +#define MX25_PAD_NF_CE0__NF_CE0 0x05c 0x26c 0x000 0x10 0x000 +#define MX25_PAD_NF_CE0__GPIO_3_22 0x05c 0x26c 0x000 0x15 0x000 + +#define MX25_PAD_ECB__ECB 0x060 0x270 0x000 0x10 0x000 +#define MX25_PAD_ECB__UART5_TXD_MUX 0x060 0x270 0x000 0x13 0x000 +#define MX25_PAD_ECB__GPIO_3_23 0x060 0x270 0x000 0x15 0x000 + +#define MX25_PAD_LBA__LBA 0x064 0x274 0x000 0x10 0x000 +#define MX25_PAD_LBA__UART5_RXD_MUX 0x064 0x274 0x578 0x13 0x000 +#define MX25_PAD_LBA__GPIO_3_24 0x064 0x274 0x000 0x15 0x000 + +#define MX25_PAD_BCLK__BCLK 0x068 0x000 0x000 0x00 0x000 +#define MX25_PAD_BCLK__GPIO_4_4 0x068 0x000 0x000 0x05 0x000 + +#define MX25_PAD_RW__RW 0x06c 0x278 0x000 0x10 0x000 +#define MX25_PAD_RW__AUD4_TXFS 0x06c 0x278 0x474 0x14 0x000 +#define MX25_PAD_RW__GPIO_3_25 0x06c 0x278 0x000 0x15 0x000 + +#define MX25_PAD_NFWE_B__NFWE_B 0x070 0x000 0x000 0x10 0x000 +#define MX25_PAD_NFWE_B__GPIO_3_26 0x070 0x000 0x000 0x15 0x000 + +#define MX25_PAD_NFRE_B__NFRE_B 0x074 0x000 0x000 0x10 0x000 +#define MX25_PAD_NFRE_B__GPIO_3_27 0x074 0x000 0x000 0x15 0x000 + +#define MX25_PAD_NFALE__NFALE 0x078 0x000 0x000 0x10 0x000 +#define MX25_PAD_NFALE__GPIO_3_28 0x078 0x000 0x000 0x15 0x000 + +#define MX25_PAD_NFCLE__NFCLE 0x07c 0x000 0x000 0x10 0x000 +#define MX25_PAD_NFCLE__GPIO_3_29 0x07c 0x000 0x000 0x15 0x000 + +#define MX25_PAD_NFWP_B__NFWP_B 0x080 0x000 0x000 0x10 0x000 +#define MX25_PAD_NFWP_B__GPIO_3_30 0x080 0x000 0x000 0x15 0x000 + +#define MX25_PAD_NFRB__NFRB 0x084 0x27c 0x000 0x10 0x000 +#define MX25_PAD_NFRB__GPIO_3_31 0x084 0x27c 0x000 0x15 0x000 + +#define MX25_PAD_D15__D15 0x088 0x280 0x000 0x00 0x000 +#define MX25_PAD_D15__LD16 0x088 0x280 0x000 0x01 0x000 +#define MX25_PAD_D15__GPIO_4_5 0x088 0x280 0x000 0x05 0x000 + +#define MX25_PAD_D14__D14 0x08c 0x284 0x000 0x00 0x000 +#define MX25_PAD_D14__LD17 0x08c 0x284 0x000 0x01 0x000 +#define MX25_PAD_D14__GPIO_4_6 0x08c 0x284 0x000 0x05 0x000 + +#define MX25_PAD_D13__D13 0x090 0x288 0x000 0x00 0x000 +#define MX25_PAD_D13__LD18 0x090 0x288 0x000 0x01 0x000 +#define MX25_PAD_D13__GPIO_4_7 0x090 0x288 0x000 0x05 0x000 + +#define MX25_PAD_D12__D12 0x094 0x28c 0x000 0x00 0x000 +#define MX25_PAD_D12__GPIO_4_8 0x094 0x28c 0x000 0x05 0x000 + +#define MX25_PAD_D11__D11 0x098 0x290 0x000 0x00 0x000 +#define MX25_PAD_D11__GPIO_4_9 0x098 0x290 0x000 0x05 0x000 + +#define MX25_PAD_D10__D10 0x09c 0x294 0x000 0x00 0x000 +#define MX25_PAD_D10__GPIO_4_10 0x09c 0x294 0x000 0x05 0x000 +#define MX25_PAD_D10__USBOTG_OC 0x09c 0x294 0x57c 0x06 0x000 + +#define MX25_PAD_D9__D9 0x0a0 0x298 0x000 0x00 0x000 +#define MX25_PAD_D9__GPIO_4_11 0x0a0 0x298 0x000 0x05 0x000 +#define MX25_PAD_D9__USBH2_PWR 0x0a0 0x298 0x000 0x06 0x000 + +#define MX25_PAD_D8__D8 0x0a4 0x29c 0x000 0x00 0x000 +#define MX25_PAD_D8__GPIO_4_12 0x0a4 0x29c 0x000 0x05 0x000 +#define MX25_PAD_D8__USBH2_OC 0x0a4 0x29c 0x580 0x06 0x000 + +#define MX25_PAD_D7__D7 0x0a8 0x2a0 0x000 0x00 0x000 +#define MX25_PAD_D7__GPIO_4_13 0x0a8 0x2a0 0x000 0x05 0x000 + +#define MX25_PAD_D6__D6 0x0ac 0x2a4 0x000 0x00 0x000 +#define MX25_PAD_D6__GPIO_4_14 0x0ac 0x2a4 0x000 0x05 0x000 + +#define MX25_PAD_D5__D5 0x0b0 0x2a8 0x000 0x00 0x000 +#define MX25_PAD_D5__GPIO_4_15 0x0b0 0x2a8 0x000 0x05 0x000 + +#define MX25_PAD_D4__D4 0x0b4 0x2ac 0x000 0x00 0x000 +#define MX25_PAD_D4__GPIO_4_16 0x0b4 0x2ac 0x000 0x05 0x000 + +#define MX25_PAD_D3__D3 0x0b8 0x2b0 0x000 0x00 0x000 +#define MX25_PAD_D3__GPIO_4_17 0x0b8 0x2b0 0x000 0x05 0x000 + +#define MX25_PAD_D2__D2 0x0bc 0x2b4 0x000 0x00 0x000 +#define MX25_PAD_D2__GPIO_4_18 0x0bc 0x2b4 0x000 0x05 0x000 + +#define MX25_PAD_D1__D1 0x0c0 0x2b8 0x000 0x00 0x000 +#define MX25_PAD_D1__GPIO_4_19 0x0c0 0x2b8 0x000 0x05 0x000 + +#define MX25_PAD_D0__D0 0x0c4 0x2bc 0x000 0x00 0x000 +#define MX25_PAD_D0__GPIO_4_20 0x0c4 0x2bc 0x000 0x05 0x000 + +#define MX25_PAD_LD0__LD0 0x0c8 0x2c0 0x000 0x10 0x000 +#define MX25_PAD_LD0__CSI_D0 0x0c8 0x2c0 0x488 0x12 0x000 +#define MX25_PAD_LD0__GPIO_2_15 0x0c8 0x2c0 0x000 0x15 0x000 + +#define MX25_PAD_LD1__LD1 0x0cc 0x2c4 0x000 0x10 0x000 +#define MX25_PAD_LD1__CSI_D1 0x0cc 0x2c4 0x48c 0x12 0x000 +#define MX25_PAD_LD1__GPIO_2_16 0x0cc 0x2c4 0x000 0x15 0x000 + +#define MX25_PAD_LD2__LD2 0x0d0 0x2c8 0x000 0x10 0x000 +#define MX25_PAD_LD2__GPIO_2_17 0x0d0 0x2c8 0x000 0x15 0x000 + +#define MX25_PAD_LD3__LD3 0x0d4 0x2cc 0x000 0x10 0x000 +#define MX25_PAD_LD3__GPIO_2_18 0x0d4 0x2cc 0x000 0x15 0x000 + +#define MX25_PAD_LD4__LD4 0x0d8 0x2d0 0x000 0x10 0x000 +#define MX25_PAD_LD4__GPIO_2_19 0x0d8 0x2d0 0x000 0x15 0x000 + +#define MX25_PAD_LD5__LD5 0x0dc 0x2d4 0x000 0x10 0x000 +#define MX25_PAD_LD5__GPIO_1_19 0x0dc 0x2d4 0x000 0x15 0x000 + +#define MX25_PAD_LD6__LD6 0x0e0 0x2d8 0x000 0x10 0x000 +#define MX25_PAD_LD6__GPIO_1_20 0x0e0 0x2d8 0x000 0x15 0x000 + +#define MX25_PAD_LD7__LD7 0x0e4 0x2dc 0x000 0x10 0x000 +#define MX25_PAD_LD7__GPIO_1_21 0x0e4 0x2dc 0x000 0x15 0x000 + +#define MX25_PAD_LD8__LD8 0x0e8 0x2e0 0x000 0x10 0x000 +#define MX25_PAD_LD8__FEC_TX_ERR 0x0e8 0x2e0 0x000 0x15 0x000 + +#define MX25_PAD_LD9__LD9 0x0ec 0x2e4 0x000 0x10 0x000 +#define MX25_PAD_LD9__FEC_COL 0x0ec 0x2e4 0x504 0x15 0x001 + +#define MX25_PAD_LD10__LD10 0x0f0 0x2e8 0x000 0x10 0x000 +#define MX25_PAD_LD10__FEC_RX_ER 0x0f0 0x2e8 0x518 0x15 0x001 + +#define MX25_PAD_LD11__LD11 0x0f4 0x2ec 0x000 0x10 0x000 +#define MX25_PAD_LD11__FEC_RDATA2 0x0f4 0x2ec 0x50c 0x15 0x001 + +#define MX25_PAD_LD12__LD12 0x0f8 0x2f0 0x000 0x10 0x000 +#define MX25_PAD_LD12__FEC_RDATA3 0x0f8 0x2f0 0x510 0x15 0x001 + +#define MX25_PAD_LD13__LD13 0x0fc 0x2f4 0x000 0x10 0x000 +#define MX25_PAD_LD13__FEC_TDATA2 0x0fc 0x2f4 0x000 0x15 0x000 + +#define MX25_PAD_LD14__LD14 0x100 0x2f8 0x000 0x10 0x000 +#define MX25_PAD_LD14__FEC_TDATA3 0x100 0x2f8 0x000 0x15 0x000 + +#define MX25_PAD_LD15__LD15 0x104 0x2fc 0x000 0x10 0x000 +#define MX25_PAD_LD15__FEC_RX_CLK 0x104 0x2fc 0x514 0x15 0x001 + +#define MX25_PAD_HSYNC__HSYNC 0x108 0x300 0x000 0x10 0x000 +#define MX25_PAD_HSYNC__GPIO_1_22 0x108 0x300 0x000 0x15 0x000 + +#define MX25_PAD_VSYNC__VSYNC 0x10c 0x304 0x000 0x10 0x000 +#define MX25_PAD_VSYNC__GPIO_1_23 0x10c 0x304 0x000 0x15 0x000 + +#define MX25_PAD_LSCLK__LSCLK 0x110 0x308 0x000 0x10 0x000 +#define MX25_PAD_LSCLK__GPIO_1_24 0x110 0x308 0x000 0x15 0x000 + +#define MX25_PAD_OE_ACD__OE_ACD 0x114 0x30c 0x000 0x10 0x000 +#define MX25_PAD_OE_ACD__GPIO_1_25 0x114 0x30c 0x000 0x15 0x000 + +#define MX25_PAD_CONTRAST__CONTRAST 0x118 0x310 0x000 0x10 0x000 +#define MX25_PAD_CONTRAST__PWM4_PWMO 0x118 0x310 0x000 0x14 0x000 +#define MX25_PAD_CONTRAST__FEC_CRS 0x118 0x310 0x508 0x15 0x001 + +#define MX25_PAD_PWM__PWM 0x11c 0x314 0x000 0x10 0x000 +#define MX25_PAD_PWM__GPIO_1_26 0x11c 0x314 0x000 0x15 0x000 +#define MX25_PAD_PWM__USBH2_OC 0x11c 0x314 0x580 0x16 0x001 + +#define MX25_PAD_CSI_D2__CSI_D2 0x120 0x318 0x000 0x10 0x000 +#define MX25_PAD_CSI_D2__UART5_RXD_MUX 0x120 0x318 0x578 0x11 0x001 +#define MX25_PAD_CSI_D2__GPIO_1_27 0x120 0x318 0x000 0x15 0x000 +#define MX25_PAD_CSI_D2__CSPI3_MOSI 0x120 0x318 0x000 0x17 0x000 + +#define MX25_PAD_CSI_D3__CSI_D3 0x124 0x31c 0x000 0x10 0x000 +#define MX25_PAD_CSI_D3__GPIO_1_28 0x124 0x31c 0x000 0x15 0x000 +#define MX25_PAD_CSI_D3__CSPI3_MISO 0x124 0x31c 0x4b4 0x17 0x001 + +#define MX25_PAD_CSI_D4__CSI_D4 0x128 0x320 0x000 0x10 0x000 +#define MX25_PAD_CSI_D4__UART5_RTS 0x128 0x320 0x574 0x11 0x001 +#define MX25_PAD_CSI_D4__GPIO_1_29 0x128 0x320 0x000 0x15 0x000 +#define MX25_PAD_CSI_D4__CSPI3_SCLK 0x128 0x320 0x000 0x17 0x000 + +#define MX25_PAD_CSI_D5__CSI_D5 0x12c 0x324 0x000 0x10 0x000 +#define MX25_PAD_CSI_D5__GPIO_1_30 0x12c 0x324 0x000 0x15 0x000 +#define MX25_PAD_CSI_D5__CSPI3_RDY 0x12c 0x324 0x000 0x17 0x000 + +#define MX25_PAD_CSI_D6__CSI_D6 0x130 0x328 0x000 0x10 0x000 +#define MX25_PAD_CSI_D6__GPIO_1_31 0x130 0x328 0x000 0x15 0x000 + +#define MX25_PAD_CSI_D7__CSI_D7 0x134 0x32c 0x000 0x10 0x000 +#define MX25_PAD_CSI_D7__GPIO_1_6 0x134 0x32c 0x000 0x15 0x000 + +#define MX25_PAD_CSI_D8__CSI_D8 0x138 0x330 0x000 0x10 0x000 +#define MX25_PAD_CSI_D8__GPIO_1_7 0x138 0x330 0x000 0x15 0x000 + +#define MX25_PAD_CSI_D9__CSI_D9 0x13c 0x334 0x000 0x10 0x000 +#define MX25_PAD_CSI_D9__GPIO_4_21 0x13c 0x334 0x000 0x15 0x000 + +#define MX25_PAD_CSI_MCLK__CSI_MCLK 0x140 0x338 0x000 0x10 0x000 +#define MX25_PAD_CSI_MCLK__GPIO_1_8 0x140 0x338 0x000 0x15 0x000 + +#define MX25_PAD_CSI_VSYNC__CSI_VSYNC 0x144 0x33c 0x000 0x10 0x000 +#define MX25_PAD_CSI_VSYNC__GPIO_1_9 0x144 0x33c 0x000 0x15 0x000 + +#define MX25_PAD_CSI_HSYNC__CSI_HSYNC 0x148 0x340 0x000 0x10 0x000 +#define MX25_PAD_CSI_HSYNC__GPIO_1_10 0x148 0x340 0x000 0x15 0x000 + +#define MX25_PAD_CSI_PIXCLK__CSI_PIXCLK 0x14c 0x344 0x000 0x10 0x000 +#define MX25_PAD_CSI_PIXCLK__GPIO_1_11 0x14c 0x344 0x000 0x15 0x000 + +#define MX25_PAD_I2C1_CLK__I2C1_CLK 0x150 0x348 0x000 0x10 0x000 +#define MX25_PAD_I2C1_CLK__GPIO_1_12 0x150 0x348 0x000 0x15 0x000 + +#define MX25_PAD_I2C1_DAT__I2C1_DAT 0x154 0x34c 0x000 0x10 0x000 +#define MX25_PAD_I2C1_DAT__GPIO_1_13 0x154 0x34c 0x000 0x15 0x000 + +#define MX25_PAD_CSPI1_MOSI__CSPI1_MOSI 0x158 0x350 0x000 0x10 0x000 +#define MX25_PAD_CSPI1_MOSI__GPIO_1_14 0x158 0x350 0x000 0x15 0x000 + +#define MX25_PAD_CSPI1_MISO__CSPI1_MISO 0x15c 0x354 0x000 0x10 0x000 +#define MX25_PAD_CSPI1_MISO__GPIO_1_15 0x15c 0x354 0x000 0x15 0x000 + +#define MX25_PAD_CSPI1_SS0__CSPI1_SS0 0x160 0x358 0x000 0x10 0x000 +#define MX25_PAD_CSPI1_SS0__GPIO_1_16 0x160 0x358 0x000 0x15 0x000 + +#define MX25_PAD_CSPI1_SS1__CSPI1_SS1 0x164 0x35c 0x000 0x10 0x000 +#define MX25_PAD_CSPI1_SS1__GPIO_1_17 0x164 0x35c 0x000 0x15 0x000 + +#define MX25_PAD_CSPI1_SCLK__CSPI1_SCLK 0x168 0x360 0x000 0x10 0x000 +#define MX25_PAD_CSPI1_SCLK__GPIO_1_18 0x168 0x360 0x000 0x15 0x000 + +#define MX25_PAD_CSPI1_RDY__CSPI1_RDY 0x16c 0x364 0x000 0x10 0x000 +#define MX25_PAD_CSPI1_RDY__GPIO_2_22 0x16c 0x364 0x000 0x15 0x000 + +#define MX25_PAD_UART1_RXD__UART1_RXD 0x170 0x368 0x000 0x10 0x000 +#define MX25_PAD_UART1_RXD__GPIO_4_22 0x170 0x368 0x000 0x15 0x000 + +#define MX25_PAD_UART1_TXD__UART1_TXD 0x174 0x36c 0x000 0x10 0x000 +#define MX25_PAD_UART1_TXD__GPIO_4_23 0x174 0x36c 0x000 0x15 0x000 + +#define MX25_PAD_UART1_RTS__UART1_RTS 0x178 0x370 0x000 0x10 0x000 +#define MX25_PAD_UART1_RTS__CSI_D0 0x178 0x370 0x488 0x11 0x001 +#define MX25_PAD_UART1_RTS__GPIO_4_24 0x178 0x370 0x000 0x15 0x000 + +#define MX25_PAD_UART1_CTS__UART1_CTS 0x17c 0x374 0x000 0x10 0x000 +#define MX25_PAD_UART1_CTS__CSI_D1 0x17c 0x374 0x48c 0x11 0x001 +#define MX25_PAD_UART1_CTS__GPIO_4_25 0x17c 0x374 0x000 0x15 0x000 + +#define MX25_PAD_UART2_RXD__UART2_RXD 0x180 0x378 0x000 0x10 0x000 +#define MX25_PAD_UART2_RXD__GPIO_4_26 0x180 0x378 0x000 0x15 0x000 + +#define MX25_PAD_UART2_TXD__UART2_TXD 0x184 0x37c 0x000 0x10 0x000 +#define MX25_PAD_UART2_TXD__GPIO_4_27 0x184 0x37c 0x000 0x15 0x000 + +#define MX25_PAD_UART2_RTS__UART2_RTS 0x188 0x380 0x000 0x10 0x000 +#define MX25_PAD_UART2_RTS__FEC_COL 0x188 0x380 0x504 0x12 0x002 +#define MX25_PAD_UART2_RTS__GPIO_4_28 0x188 0x380 0x000 0x15 0x000 + +#define MX25_PAD_UART2_CTS__FEC_RX_ER 0x18c 0x384 0x518 0x12 0x002 +#define MX25_PAD_UART2_CTS__UART2_CTS 0x18c 0x384 0x000 0x10 0x000 +#define MX25_PAD_UART2_CTS__GPIO_4_29 0x18c 0x384 0x000 0x15 0x000 + +#define MX25_PAD_SD1_CMD__SD1_CMD 0x190 0x388 0x000 0x10 0x000 +#define MX25_PAD_SD1_CMD__FEC_RDATA2 0x190 0x388 0x50c 0x12 0x002 +#define MX25_PAD_SD1_CMD__GPIO_2_23 0x190 0x388 0x000 0x15 0x000 + +#define MX25_PAD_SD1_CLK__SD1_CLK 0x194 0x38c 0x000 0x10 0x000 +#define MX25_PAD_SD1_CLK__FEC_RDATA3 0x194 0x38c 0x510 0x12 0x002 +#define MX25_PAD_SD1_CLK__GPIO_2_24 0x194 0x38c 0x000 0x15 0x000 + +#define MX25_PAD_SD1_DATA0__SD1_DATA0 0x198 0x390 0x000 0x10 0x000 +#define MX25_PAD_SD1_DATA0__GPIO_2_25 0x198 0x390 0x000 0x15 0x000 + +#define MX25_PAD_SD1_DATA1__SD1_DATA1 0x19c 0x394 0x000 0x10 0x000 +#define MX25_PAD_SD1_DATA1__AUD7_RXD 0x19c 0x394 0x478 0x13 0x000 +#define MX25_PAD_SD1_DATA1__GPIO_2_26 0x19c 0x394 0x000 0x15 0x000 + +#define MX25_PAD_SD1_DATA2__SD1_DATA2 0x1a0 0x398 0x000 0x10 0x000 +#define MX25_PAD_SD1_DATA2__FEC_RX_CLK 0x1a0 0x398 0x514 0x15 0x002 +#define MX25_PAD_SD1_DATA2__GPIO_2_27 0x1a0 0x398 0x000 0x15 0x000 + +#define MX25_PAD_SD1_DATA3__SD1_DATA3 0x1a4 0x39c 0x000 0x10 0x000 +#define MX25_PAD_SD1_DATA3__FEC_CRS 0x1a4 0x39c 0x508 0x10 0x002 +#define MX25_PAD_SD1_DATA3__GPIO_2_28 0x1a4 0x39c 0x000 0x15 0x000 + +#define MX25_PAD_KPP_ROW0__KPP_ROW0 0x1a8 0x3a0 0x000 0x10 0x000 +#define MX25_PAD_KPP_ROW0__GPIO_2_29 0x1a8 0x3a0 0x000 0x15 0x000 + +#define MX25_PAD_KPP_ROW1__KPP_ROW1 0x1ac 0x3a4 0x000 0x10 0x000 +#define MX25_PAD_KPP_ROW1__GPIO_2_30 0x1ac 0x3a4 0x000 0x15 0x000 + +#define MX25_PAD_KPP_ROW2__KPP_ROW2 0x1b0 0x3a8 0x000 0x10 0x000 +#define MX25_PAD_KPP_ROW2__CSI_D0 0x1b0 0x3a8 0x488 0x13 0x002 +#define MX25_PAD_KPP_ROW2__GPIO_2_31 0x1b0 0x3a8 0x000 0x15 0x000 + +#define MX25_PAD_KPP_ROW3__KPP_ROW3 0x1b4 0x3ac 0x000 0x10 0x000 +#define MX25_PAD_KPP_ROW3__CSI_LD1 0x1b4 0x3ac 0x48c 0x13 0x002 +#define MX25_PAD_KPP_ROW3__GPIO_3_0 0x1b4 0x3ac 0x000 0x15 0x000 + +#define MX25_PAD_KPP_COL0__KPP_COL0 0x1b8 0x3b0 0x000 0x10 0x000 +#define MX25_PAD_KPP_COL0__UART4_RXD_MUX 0x1b8 0x3b0 0x570 0x11 0x001 +#define MX25_PAD_KPP_COL0__AUD5_TXD 0x1b8 0x3b0 0x000 0x12 0x000 +#define MX25_PAD_KPP_COL0__GPIO_3_1 0x1b8 0x3b0 0x000 0x15 0x000 + +#define MX25_PAD_KPP_COL1__KPP_COL1 0x1bc 0x3b4 0x000 0x10 0x000 +#define MX25_PAD_KPP_COL1__UART4_TXD_MUX 0x1bc 0x3b4 0x000 0x11 0x000 +#define MX25_PAD_KPP_COL1__AUD5_RXD 0x1bc 0x3b4 0x000 0x12 0x000 +#define MX25_PAD_KPP_COL1__GPIO_3_2 0x1bc 0x3b4 0x000 0x15 0x000 + +#define MX25_PAD_KPP_COL2__KPP_COL2 0x1c0 0x3b8 0x000 0x10 0x000 +#define MX25_PAD_KPP_COL2__UART4_RTS 0x1c0 0x3b8 0x000 0x11 0x000 +#define MX25_PAD_KPP_COL2__AUD5_TXC 0x1c0 0x3b8 0x000 0x12 0x000 +#define MX25_PAD_KPP_COL2__GPIO_3_3 0x1c0 0x3b8 0x000 0x15 0x000 + +#define MX25_PAD_KPP_COL3__KPP_COL3 0x1c4 0x3bc 0x000 0x10 0x000 +#define MX25_PAD_KPP_COL3__UART4_CTS 0x1c4 0x3bc 0x000 0x11 0x000 +#define MX25_PAD_KPP_COL3__AUD5_TXFS 0x1c4 0x3bc 0x000 0x12 0x000 +#define MX25_PAD_KPP_COL3__GPIO_3_4 0x1c4 0x3bc 0x000 0x15 0x000 + +#define MX25_PAD_FEC_MDC__FEC_MDC 0x1c8 0x3c0 0x000 0x10 0x000 +#define MX25_PAD_FEC_MDC__AUD4_TXD 0x1c8 0x3c0 0x464 0x12 0x001 +#define MX25_PAD_FEC_MDC__GPIO_3_5 0x1c8 0x3c0 0x000 0x15 0x000 + +#define MX25_PAD_FEC_MDIO__FEC_MDIO 0x1cc 0x3c4 0x000 0x10 0x000 +#define MX25_PAD_FEC_MDIO__AUD4_RXD 0x1cc 0x3c4 0x460 0x12 0x001 +#define MX25_PAD_FEC_MDIO__GPIO_3_6 0x1cc 0x3c4 0x000 0x15 0x000 + +#define MX25_PAD_FEC_TDATA0__FEC_TDATA0 0x1d0 0x3c8 0x000 0x10 0x000 +#define MX25_PAD_FEC_TDATA0__GPIO_3_7 0x1d0 0x3c8 0x000 0x15 0x000 + +#define MX25_PAD_FEC_TDATA1__FEC_TDATA1 0x1d4 0x3cc 0x000 0x10 0x000 +#define MX25_PAD_FEC_TDATA1__AUD4_TXFS 0x1d4 0x3cc 0x474 0x12 0x001 +#define MX25_PAD_FEC_TDATA1__GPIO_3_8 0x1d4 0x3cc 0x000 0x15 0x000 + +#define MX25_PAD_FEC_TX_EN__FEC_TX_EN 0x1d8 0x3d0 0x000 0x10 0x000 +#define MX25_PAD_FEC_TX_EN__GPIO_3_9 0x1d8 0x3d0 0x000 0x15 0x000 + +#define MX25_PAD_FEC_RDATA0__FEC_RDATA0 0x1dc 0x3d4 0x000 0x10 0x000 +#define MX25_PAD_FEC_RDATA0__GPIO_3_10 0x1dc 0x3d4 0x000 0x15 0x000 + +#define MX25_PAD_FEC_RDATA1__FEC_RDATA1 0x1e0 0x3d8 0x000 0x10 0x000 +#define MX25_PAD_FEC_RDATA1__GPIO_3_11 0x1e0 0x3d8 0x000 0x15 0x000 + +#define MX25_PAD_FEC_RX_DV__FEC_RX_DV 0x1e4 0x3dc 0x000 0x10 0x000 +#define MX25_PAD_FEC_RX_DV__CAN2_RX 0x1e4 0x3dc 0x484 0x14 0x000 +#define MX25_PAD_FEC_RX_DV__GPIO_3_12 0x1e4 0x3dc 0x000 0x15 0x000 + +#define MX25_PAD_FEC_TX_CLK__FEC_TX_CLK 0x1e8 0x3e0 0x000 0x10 0x000 +#define MX25_PAD_FEC_TX_CLK__GPIO_3_13 0x1e8 0x3e0 0x000 0x15 0x000 + +#define MX25_PAD_RTCK__RTCK 0x1ec 0x3e4 0x000 0x10 0x000 +#define MX25_PAD_RTCK__OWIRE 0x1ec 0x3e4 0x000 0x11 0x000 +#define MX25_PAD_RTCK__GPIO_3_14 0x1ec 0x3e4 0x000 0x15 0x000 + +#define MX25_PAD_DE_B__DE_B 0x1f0 0x3ec 0x000 0x10 0x000 +#define MX25_PAD_DE_B__GPIO_2_20 0x1f0 0x3ec 0x000 0x15 0x000 + +#define MX25_PAD_TDO__TDO 0x000 0x3e8 0x000 0x00 0x000 + +#define MX25_PAD_GPIO_A__GPIO_A 0x1f4 0x3f0 0x000 0x10 0x000 +#define MX25_PAD_GPIO_A__CAN1_TX 0x1f4 0x3f0 0x000 0x16 0x000 +#define MX25_PAD_GPIO_A__USBOTG_PWR 0x1f4 0x3f0 0x000 0x12 0x000 + +#define MX25_PAD_GPIO_B__GPIO_B 0x1f8 0x3f4 0x000 0x10 0x000 +#define MX25_PAD_GPIO_B__CAN1_RX 0x1f8 0x3f4 0x480 0x16 0x001 +#define MX25_PAD_GPIO_B__USBOTG_OC 0x1f8 0x3f4 0x57c 0x12 0x001 + +#define MX25_PAD_GPIO_C__GPIO_C 0x1fc 0x3f8 0x000 0x10 0x000 +#define MX25_PAD_GPIO_C__CAN2_TX 0x1fc 0x3f8 0x000 0x16 0x000 + +#define MX25_PAD_GPIO_D__GPIO_D 0x200 0x3fc 0x000 0x10 0x000 +#define MX25_PAD_GPIO_E__LD16 0x204 0x400 0x000 0x02 0x000 +#define MX25_PAD_GPIO_D__CAN2_RX 0x200 0x3fc 0x484 0x16 0x001 + +#define MX25_PAD_GPIO_E__GPIO_E 0x204 0x400 0x000 0x10 0x000 +#define MX25_PAD_GPIO_F__LD17 0x208 0x404 0x000 0x02 0x000 +#define MX25_PAD_GPIO_E__AUD7_TXD 0x204 0x400 0x000 0x14 0x000 + +#define MX25_PAD_GPIO_F__GPIO_F 0x208 0x404 0x000 0x10 0x000 +#define MX25_PAD_GPIO_F__AUD7_TXC 0x208 0x404 0x000 0x14 0x000 + +#define MX25_PAD_EXT_ARMCLK__EXT_ARMCLK 0x20c 0x000 0x000 0x10 0x000 +#define MX25_PAD_EXT_ARMCLK__GPIO_3_15 0x20c 0x000 0x000 0x15 0x000 + +#define MX25_PAD_UPLL_BYPCLK__UPLL_BYPCLK 0x210 0x000 0x000 0x10 0x000 +#define MX25_PAD_UPLL_BYPCLK__GPIO_3_16 0x210 0x000 0x000 0x15 0x000 + +#define MX25_PAD_VSTBY_REQ__VSTBY_REQ 0x214 0x408 0x000 0x10 0x000 +#define MX25_PAD_VSTBY_REQ__AUD7_TXFS 0x214 0x408 0x000 0x14 0x000 +#define MX25_PAD_VSTBY_REQ__GPIO_3_17 0x214 0x408 0x000 0x15 0x000 +#define MX25_PAD_VSTBY_ACK__VSTBY_ACK 0x218 0x40c 0x000 0x10 0x000 +#define MX25_PAD_VSTBY_ACK__GPIO_3_18 0x218 0x40c 0x000 0x15 0x000 + +#define MX25_PAD_POWER_FAIL__POWER_FAIL 0x21c 0x410 0x000 0x10 0x000 +#define MX25_PAD_POWER_FAIL__AUD7_RXD 0x21c 0x410 0x478 0x14 0x001 +#define MX25_PAD_POWER_FAIL__GPIO_3_19 0x21c 0x410 0x000 0x15 0x000 + +#define MX25_PAD_CLKO__CLKO 0x220 0x414 0x000 0x10 0x000 +#define MX25_PAD_CLKO__GPIO_2_21 0x220 0x414 0x000 0x15 0x000 + +#define MX25_PAD_BOOT_MODE0__BOOT_MODE0 0x224 0x000 0x000 0x00 0x000 +#define MX25_PAD_BOOT_MODE0__GPIO_4_30 0x224 0x000 0x000 0x05 0x000 +#define MX25_PAD_BOOT_MODE1__BOOT_MODE1 0x228 0x000 0x000 0x00 0x000 +#define MX25_PAD_BOOT_MODE1__GPIO_4_31 0x228 0x000 0x000 0x05 0x000 + +#endif /* __DTS_IMX25_PINFUNC_H */ diff --git a/arch/arm/boot/dts/imx25.dtsi b/arch/arm/boot/dts/imx25.dtsi index 737ed5da8f71..32f760e24898 100644 --- a/arch/arm/boot/dts/imx25.dtsi +++ b/arch/arm/boot/dts/imx25.dtsi @@ -10,6 +10,7 @@ */ #include "skeleton.dtsi" +#include "imx25-pinfunc.h" / { aliases { @@ -173,12 +174,12 @@ status = "disabled"; }; - iomuxc@43fac000{ + iomuxc: iomuxc@43fac000 { compatible = "fsl,imx25-iomuxc"; reg = <0x43fac000 0x4000>; }; - audmux@43fb0000 { + audmux: audmux@43fb0000 { compatible = "fsl,imx25-audmux", "fsl,imx31-audmux"; reg = <0x43fb0000 0x4000>; status = "disabled"; @@ -236,6 +237,11 @@ compatible = "fsl,imx25-ssi", "fsl,imx21-ssi"; reg = <0x50014000 0x4000>; interrupts = <11>; + clocks = <&clks 118>; + clock-names = "ipg"; + dmas = <&sdma 24 1 0>, + <&sdma 25 1 0>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -266,6 +272,11 @@ compatible = "fsl,imx25-ssi", "fsl,imx21-ssi"; reg = <0x50034000 0x4000>; interrupts = <12>; + clocks = <&clks 117>; + clock-names = "ipg"; + dmas = <&sdma 28 1 0>, + <&sdma 29 1 0>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -436,13 +447,14 @@ #interrupt-cells = <2>; }; - sdma@53fd4000 { + sdma: sdma@53fd4000 { compatible = "fsl,imx25-sdma", "fsl,imx35-sdma"; reg = <0x53fd4000 0x4000>; clocks = <&clks 112>, <&clks 68>; clock-names = "ipg", "ahb"; #dma-cells = <3>; interrupts = <34>; + fsl,sdma-ram-script-name = "imx/sdma/sdma-imx25.bin"; }; wdog@53fdc000 { diff --git a/arch/arm/boot/dts/imx27-apf27.dts b/arch/arm/boot/dts/imx27-apf27.dts index ba4c6df08ece..09f57b39e3ef 100644 --- a/arch/arm/boot/dts/imx27-apf27.dts +++ b/arch/arm/boot/dts/imx27-apf27.dts @@ -34,11 +34,49 @@ }; }; +&iomuxc { + imx27-apf27 { + pinctrl_fec1: fec1grp { + fsl,pins = < + MX27_PAD_SD3_CMD__FEC_TXD0 0x0 + MX27_PAD_SD3_CLK__FEC_TXD1 0x0 + MX27_PAD_ATA_DATA0__FEC_TXD2 0x0 + MX27_PAD_ATA_DATA1__FEC_TXD3 0x0 + MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0 + MX27_PAD_ATA_DATA3__FEC_RXD1 0x0 + MX27_PAD_ATA_DATA4__FEC_RXD2 0x0 + MX27_PAD_ATA_DATA5__FEC_RXD3 0x0 + MX27_PAD_ATA_DATA6__FEC_MDIO 0x0 + MX27_PAD_ATA_DATA7__FEC_MDC 0x0 + MX27_PAD_ATA_DATA8__FEC_CRS 0x0 + MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0 + MX27_PAD_ATA_DATA10__FEC_RXD0 0x0 + MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0 + MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0 + MX27_PAD_ATA_DATA13__FEC_COL 0x0 + MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0 + MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX27_PAD_UART1_TXD__UART1_TXD 0x0 + MX27_PAD_UART1_RXD__UART1_RXD 0x0 + >; + }; + }; +}; + &uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; status = "okay"; }; &fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx27-apf27dev.dts b/arch/arm/boot/dts/imx27-apf27dev.dts index 47c8c26012e4..2b6d489dae69 100644 --- a/arch/arm/boot/dts/imx27-apf27dev.dts +++ b/arch/arm/boot/dts/imx27-apf27dev.dts @@ -22,10 +22,10 @@ bits-per-pixel = <16>; /* non-standard but required */ fsl,pcr = <0xfae80083>; /* non-standard but required */ display-timings { - timing0: 640x480 { + timing0: 800x480 { clock-frequency = <33000033>; hactive = <800>; - vactive = <640>; + vactive = <480>; hback-porch = <96>; hfront-porch = <96>; vback-porch = <20>; @@ -38,20 +38,24 @@ gpio-keys { compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys>; user-key { label = "user"; - gpios = <&gpio6 13 0>; + gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>; linux,code = <276>; /* BTN_EXTRA */ }; }; leds { compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; user { label = "Heartbeat"; - gpios = <&gpio6 14 0>; + gpios = <&gpio6 14 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; }; @@ -59,25 +63,34 @@ &cspi1 { fsl,spi-num-chipselects = <1>; - cs-gpios = <&gpio4 28 1>; + cs-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_cspi1 &pinctrl_cspi1_cs>; status = "okay"; }; &cspi2 { fsl,spi-num-chipselects = <3>; - cs-gpios = <&gpio4 21 1>, <&gpio4 27 1>, - <&gpio2 17 1>; + cs-gpios = <&gpio4 21 GPIO_ACTIVE_LOW>, + <&gpio4 27 GPIO_ACTIVE_LOW>, + <&gpio2 17 GPIO_ACTIVE_LOW>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_cspi2 &pinctrl_cspi2_cs>; status = "okay"; }; &fb { display = <&display>; fsl,dmacr = <0x00020010>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_imxfb1>; status = "okay"; }; &i2c1 { clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; status = "okay"; rtc@68 { @@ -87,5 +100,127 @@ }; &i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; status = "okay"; }; + +&iomuxc { + imx27-apf27dev { + pinctrl_cspi1: cspi1grp { + fsl,pins = < + MX27_PAD_CSPI1_MISO__CSPI1_MISO 0x0 + MX27_PAD_CSPI1_MOSI__CSPI1_MOSI 0x0 + MX27_PAD_CSPI1_SCLK__CSPI1_SCLK 0x0 + >; + }; + + pinctrl_cspi1_cs: cspi1csgrp { + fsl,pins = <MX27_PAD_CSPI1_SS0__GPIO4_28 0x0>; + }; + + pinctrl_cspi2: cspi2grp { + fsl,pins = < + MX27_PAD_CSPI2_MISO__CSPI2_MISO 0x0 + MX27_PAD_CSPI2_MOSI__CSPI2_MOSI 0x0 + MX27_PAD_CSPI2_SCLK__CSPI2_SCLK 0x0 + >; + }; + + pinctrl_cspi2_cs: cspi2csgrp { + fsl,pins = < + MX27_PAD_CSI_D5__GPIO2_17 0x0 + MX27_PAD_CSPI2_SS0__GPIO4_21 0x0 + MX27_PAD_CSPI1_SS1__GPIO4_27 0x0 + >; + }; + + pinctrl_gpio_leds: gpioledsgrp { + fsl,pins = <MX27_PAD_PC_VS1__GPIO6_14 0x0>; + }; + + pinctrl_gpio_keys: gpiokeysgrp { + fsl,pins = <MX27_PAD_PC_VS2__GPIO6_13 0x0>; + }; + + pinctrl_imxfb1: imxfbgrp { + fsl,pins = < + MX27_PAD_CLS__CLS 0x0 + MX27_PAD_CONTRAST__CONTRAST 0x0 + MX27_PAD_LD0__LD0 0x0 + MX27_PAD_LD1__LD1 0x0 + MX27_PAD_LD2__LD2 0x0 + MX27_PAD_LD3__LD3 0x0 + MX27_PAD_LD4__LD4 0x0 + MX27_PAD_LD5__LD5 0x0 + MX27_PAD_LD6__LD6 0x0 + MX27_PAD_LD7__LD7 0x0 + MX27_PAD_LD8__LD8 0x0 + MX27_PAD_LD9__LD9 0x0 + MX27_PAD_LD10__LD10 0x0 + MX27_PAD_LD11__LD11 0x0 + MX27_PAD_LD12__LD12 0x0 + MX27_PAD_LD13__LD13 0x0 + MX27_PAD_LD14__LD14 0x0 + MX27_PAD_LD15__LD15 0x0 + MX27_PAD_LD16__LD16 0x0 + MX27_PAD_LD17__LD17 0x0 + MX27_PAD_LSCLK__LSCLK 0x0 + MX27_PAD_OE_ACD__OE_ACD 0x0 + MX27_PAD_PS__PS 0x0 + MX27_PAD_REV__REV 0x0 + MX27_PAD_SPL_SPR__SPL_SPR 0x0 + MX27_PAD_HSYNC__HSYNC 0x0 + MX27_PAD_VSYNC__VSYNC 0x0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX27_PAD_I2C_DATA__I2C_DATA 0x0 + MX27_PAD_I2C_CLK__I2C_CLK 0x0 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX27_PAD_I2C2_SDA__I2C2_SDA 0x0 + MX27_PAD_I2C2_SCL__I2C2_SCL 0x0 + >; + }; + + pinctrl_pwm: pwmgrp { + fsl,pins = < + MX27_PAD_PWMO__PWMO 0x0 + >; + }; + + pinctrl_sdhc2: sdhc2grp { + fsl,pins = < + MX27_PAD_SD2_CLK__SD2_CLK 0x0 + MX27_PAD_SD2_CMD__SD2_CMD 0x0 + MX27_PAD_SD2_D0__SD2_D0 0x0 + MX27_PAD_SD2_D1__SD2_D1 0x0 + MX27_PAD_SD2_D2__SD2_D2 0x0 + MX27_PAD_SD2_D3__SD2_D3 0x0 + >; + }; + + pinctrl_sdhc2_cd: sdhc2cdgrp { + fsl,pins = <MX27_PAD_TOUT__GPIO3_14 0x0>; + }; + }; +}; + +&sdhci2 { + bus-width = <4>; + cd-gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdhc2 &pinctrl_sdhc2_cd>; + status = "okay"; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm>; +}; diff --git a/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts b/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts index 5a31c776513f..3c3964a99637 100644 --- a/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts +++ b/arch/arm/boot/dts/imx27-phytec-phycard-s-rdk.dts @@ -9,7 +9,7 @@ * http://www.gnu.org/copyleft/gpl.html */ -#include "imx27-phytec-phycard-s-som.dts" +#include "imx27-phytec-phycard-s-som.dtsi" / { model = "Phytec pca100 rapid development kit"; @@ -37,9 +37,12 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_3v3: 3v3 { + reg_3v3: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "3V3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; @@ -54,6 +57,8 @@ }; &i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; status = "okay"; rtc@51 { @@ -68,26 +73,92 @@ }; }; +&iomuxc { + imx27-phycard-s-rdk { + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX27_PAD_I2C2_SDA__I2C2_SDA 0x0 + MX27_PAD_I2C2_SCL__I2C2_SCL 0x0 + >; + }; + + pinctrl_owire1: owire1grp { + fsl,pins = < + MX27_PAD_RTCK__OWIRE 0x0 + >; + }; + + pinctrl_sdhc2: sdhc2grp { + fsl,pins = < + MX27_PAD_SD2_CLK__SD2_CLK 0x0 + MX27_PAD_SD2_CMD__SD2_CMD 0x0 + MX27_PAD_SD2_D0__SD2_D0 0x0 + MX27_PAD_SD2_D1__SD2_D1 0x0 + MX27_PAD_SD2_D2__SD2_D2 0x0 + MX27_PAD_SD2_D3__SD2_D3 0x0 + MX27_PAD_SSI3_RXDAT__GPIO3_29 0x0 /* CD */ + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX27_PAD_UART1_TXD__UART1_TXD 0x0 + MX27_PAD_UART1_RXD__UART1_RXD 0x0 + MX27_PAD_UART1_CTS__UART1_CTS 0x0 + MX27_PAD_UART1_RTS__UART1_RTS 0x0 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX27_PAD_UART2_TXD__UART2_TXD 0x0 + MX27_PAD_UART2_RXD__UART2_RXD 0x0 + MX27_PAD_UART2_CTS__UART2_CTS 0x0 + MX27_PAD_UART2_RTS__UART2_RTS 0x0 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX27_PAD_UART3_TXD__UART3_TXD 0x0 + MX27_PAD_UART3_RXD__UART3_RXD 0x0 + MX27_PAD_UART3_CTS__UART3_CTS 0x0 + MX27_PAD_UART3_RTS__UART3_RTS 0x0 + >; + }; + }; +}; + &owire { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_owire1>; status = "okay"; }; &sdhci2 { - cd-gpios = <&gpio3 29 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdhc2>; + cd-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>; status = "okay"; }; &uart1 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; status = "okay"; }; &uart2 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; status = "okay"; }; &uart3 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts b/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts deleted file mode 100644 index c8d57d1d0743..000000000000 --- a/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dts +++ /dev/null @@ -1,44 +0,0 @@ -/* - * Copyright 2012 Sascha Hauer, Uwe Kleine-König, Steffen Trumtrar - * and Markus Pargmann, Pengutronix - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ - -/dts-v1/; -#include "imx27.dtsi" - -/ { - model = "Phytec pca100"; - compatible = "phytec,imx27-pca100", "fsl,imx27"; - - memory { - reg = <0xa0000000 0x08000000>; /* 128MB */ - }; -}; - -&cspi1 { - fsl,spi-num-chipselects = <2>; - cs-gpios = <&gpio4 28 0>, - <&gpio4 27 0>; - status = "okay"; -}; - -&fec { - status = "okay"; -}; - -&i2c2 { - status = "okay"; - - at24@52 { - compatible = "at,24c32"; - pagesize = <32>; - reg = <0x52>; - }; -}; diff --git a/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dtsi b/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dtsi new file mode 100644 index 000000000000..1b6248079682 --- /dev/null +++ b/arch/arm/boot/dts/imx27-phytec-phycard-s-som.dtsi @@ -0,0 +1,103 @@ +/* + * Copyright 2012 Sascha Hauer, Uwe Kleine-König, Steffen Trumtrar + * and Markus Pargmann, Pengutronix + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx27.dtsi" + +/ { + model = "Phytec pca100"; + compatible = "phytec,imx27-pca100", "fsl,imx27"; + + memory { + reg = <0xa0000000 0x08000000>; /* 128MB */ + }; +}; + +&cspi1 { + fsl,spi-num-chipselects = <2>; + cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>, + <&gpio4 27 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + at24@52 { + compatible = "at,24c32"; + pagesize = <32>; + reg = <0x52>; + }; +}; + +&iomuxc { + imx27-phycard-s-som { + pinctrl_fec1: fec1grp { + fsl,pins = < + MX27_PAD_SD3_CMD__FEC_TXD0 0x0 + MX27_PAD_SD3_CLK__FEC_TXD1 0x0 + MX27_PAD_ATA_DATA0__FEC_TXD2 0x0 + MX27_PAD_ATA_DATA1__FEC_TXD3 0x0 + MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0 + MX27_PAD_ATA_DATA3__FEC_RXD1 0x0 + MX27_PAD_ATA_DATA4__FEC_RXD2 0x0 + MX27_PAD_ATA_DATA5__FEC_RXD3 0x0 + MX27_PAD_ATA_DATA6__FEC_MDIO 0x0 + MX27_PAD_ATA_DATA7__FEC_MDC 0x0 + MX27_PAD_ATA_DATA8__FEC_CRS 0x0 + MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0 + MX27_PAD_ATA_DATA10__FEC_RXD0 0x0 + MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0 + MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0 + MX27_PAD_ATA_DATA13__FEC_COL 0x0 + MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0 + MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX27_PAD_I2C2_SDA__I2C2_SDA 0x0 + MX27_PAD_I2C2_SCL__I2C2_SCL 0x0 + >; + }; + + pinctrl_nfc: nfcgrp { + fsl,pins = < + MX27_PAD_NFRB__NFRB 0x0 + MX27_PAD_NFCLE__NFCLE 0x0 + MX27_PAD_NFWP_B__NFWP_B 0x0 + MX27_PAD_NFCE_B__NFCE_B 0x0 + MX27_PAD_NFALE__NFALE 0x0 + MX27_PAD_NFRE_B__NFRE_B 0x0 + MX27_PAD_NFWE_B__NFWE_B 0x0 + >; + }; + }; +}; + +&nfc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nfc>; + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts index 0fc6551786c6..df3b2e731835 100644 --- a/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts +++ b/arch/arm/boot/dts/imx27-phytec-phycore-rdk.dts @@ -7,7 +7,7 @@ * http://www.gnu.org/copyleft/gpl.html */ -#include "imx27-phytec-phycore-som.dts" +#include "imx27-phytec-phycore-som.dtsi" / { model = "Phytec pcm970"; @@ -16,32 +16,200 @@ &cspi1 { fsl,spi-num-chipselects = <2>; - cs-gpios = <&gpio4 28 0>, <&gpio4 27 0>; + cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>, + <&gpio4 27 GPIO_ACTIVE_LOW>; +}; + +&i2c1 { + clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + camgpio: pca9536@41 { + compatible = "nxp,pca9536"; + reg = <0x41>; + gpio-controller; + #gpio-cells = <2>; + }; +}; + +&iomuxc { + imx27_phycore_rdk { + pinctrl_i2c1: i2c1grp { + /* Add pullup to DATA line */ + fsl,pins = < + MX27_PAD_I2C_DATA__I2C_DATA 0x1 + MX27_PAD_I2C_CLK__I2C_CLK 0x0 + >; + }; + + pinctrl_owire1: owire1grp { + fsl,pins = < + MX27_PAD_RTCK__OWIRE 0x0 + >; + }; + + pinctrl_sdhc2: sdhc2grp { + fsl,pins = < + MX27_PAD_SD2_CLK__SD2_CLK 0x0 + MX27_PAD_SD2_CMD__SD2_CMD 0x0 + MX27_PAD_SD2_D0__SD2_D0 0x0 + MX27_PAD_SD2_D1__SD2_D1 0x0 + MX27_PAD_SD2_D2__SD2_D2 0x0 + MX27_PAD_SD2_D3__SD2_D3 0x0 + MX27_PAD_SSI3_FS__GPIO3_28 0x0 /* WP */ + MX27_PAD_SSI3_RXDAT__GPIO3_29 0x0 /* CD */ + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX27_PAD_UART1_TXD__UART1_TXD 0x0 + MX27_PAD_UART1_RXD__UART1_RXD 0x0 + MX27_PAD_UART1_CTS__UART1_CTS 0x0 + MX27_PAD_UART1_RTS__UART1_RTS 0x0 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX27_PAD_UART2_TXD__UART2_TXD 0x0 + MX27_PAD_UART2_RXD__UART2_RXD 0x0 + MX27_PAD_UART2_CTS__UART2_CTS 0x0 + MX27_PAD_UART2_RTS__UART2_RTS 0x0 + >; + }; + + pinctrl_usbh2: usbh2grp { + fsl,pins = < + MX27_PAD_USBH2_CLK__USBH2_CLK 0x0 + MX27_PAD_USBH2_DIR__USBH2_DIR 0x0 + MX27_PAD_USBH2_NXT__USBH2_NXT 0x0 + MX27_PAD_USBH2_STP__USBH2_STP 0x0 + MX27_PAD_CSPI2_SCLK__USBH2_DATA0 0x0 + MX27_PAD_CSPI2_MOSI__USBH2_DATA1 0x0 + MX27_PAD_CSPI2_MISO__USBH2_DATA2 0x0 + MX27_PAD_CSPI2_SS1__USBH2_DATA3 0x0 + MX27_PAD_CSPI2_SS2__USBH2_DATA4 0x0 + MX27_PAD_CSPI1_SS2__USBH2_DATA5 0x0 + MX27_PAD_CSPI2_SS0__USBH2_DATA6 0x0 + MX27_PAD_USBH2_DATA7__USBH2_DATA7 0x0 + >; + }; + + pinctrl_weim: weimgrp { + fsl,pins = < + MX27_PAD_CS4_B__CS4_B 0x0 /* CS4 */ + MX27_PAD_SD1_D1__GPIO5_19 0x0 /* CAN IRQ */ + >; + }; + }; +}; + +&owire { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_owire1>; + status = "okay"; +}; + +&pmicleds { + ledr1: led@3 { + reg = <3>; + label = "system:red1:user"; + }; + + ledg1: led@4 { + reg = <4>; + label = "system:green1:user"; + }; + + ledb1: led@5 { + reg = <5>; + label = "system:blue1:user"; + }; + + ledr2: led@6 { + reg = <6>; + label = "system:red2:user"; + }; + + ledg2: led@7 { + reg = <7>; + label = "system:green2:user"; + }; + + ledb2: led@8 { + reg = <8>; + label = "system:blue2:user"; + }; + + ledr3: led@9 { + reg = <9>; + label = "system:red3:nand"; + linux,default-trigger = "nand-disk"; + }; + + ledg3: led@10 { + reg = <10>; + label = "system:green3:live"; + linux,default-trigger = "heartbeat"; + }; + + ledb3: led@11 { + reg = <11>; + label = "system:blue3:cpu"; + linux,default-trigger = "cpu0"; + }; }; &sdhci2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdhc2>; bus-width = <4>; - cd-gpios = <&gpio3 29 0>; - wp-gpios = <&gpio3 28 0>; + cd-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH>; + wp-gpios = <&gpio3 28 GPIO_ACTIVE_HIGH>; vmmc-supply = <&vmmc1_reg>; status = "okay"; }; &uart1 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; }; &uart2 { fsl,uart-has-rtscts; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usbh2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh2>; + dr_mode = "host"; + phy_type = "ulpi"; + vbus-supply = <®_5v0>; + disable-over-current; status = "okay"; }; +&usbphy2 { + vcc-supply = <®_5v0>; +}; + &weim { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_weim>; + can@d4000000 { compatible = "nxp,sja1000"; reg = <4 0x00000000 0x00000100>; interrupt-parent = <&gpio5>; - interrupts = <19 0x2>; + interrupts = <19 IRQ_TYPE_EDGE_FALLING>; nxp,external-clock-frequency = <16000000>; nxp,tx-output-config = <0x16>; nxp,no-comparator-bypass; diff --git a/arch/arm/boot/dts/imx27-phytec-phycore-som.dts b/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi index 4ec402c38945..cefaa6994623 100644 --- a/arch/arm/boot/dts/imx27-phytec-phycore-som.dts +++ b/arch/arm/boot/dts/imx27-phytec-phycore-som.dtsi @@ -19,6 +19,28 @@ memory { reg = <0xa0000000 0x08000000>; }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_3v3: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + reg_5v0: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "5V0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + }; }; &audmux { @@ -37,21 +59,30 @@ }; &cspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_cspi1>; fsl,spi-num-chipselects = <1>; - cs-gpios = <&gpio4 28 0>; + cs-gpios = <&gpio4 28 GPIO_ACTIVE_HIGH>; status = "okay"; pmic: mc13783@0 { #address-cells = <1>; #size-cells = <0>; compatible = "fsl,mc13783"; - spi-max-frequency = <20000000>; reg = <0>; + spi-cs-high; + spi-max-frequency = <20000000>; interrupt-parent = <&gpio2>; - interrupts = <23 0x4>; + interrupts = <23 IRQ_TYPE_LEVEL_HIGH>; fsl,mc13xxx-uses-adc; fsl,mc13xxx-uses-rtc; + pmicleds: leds { + #address-cells = <1>; + #size-cells = <0>; + led-control = <0x001 0x000 0x000 0x000 0x000 0x000>; + }; + regulators { /* SW1A and SW1B joined operation */ sw1_reg: sw1a { @@ -134,12 +165,18 @@ }; &fec { - phy-reset-gpios = <&gpio3 30 0>; + phy-mode = "mii"; + phy-reset-gpios = <&gpio3 30 GPIO_ACTIVE_HIGH>; + phy-supply = <®_3v3>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec1>; status = "okay"; }; &i2c2 { clock-frequency = <400000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; status = "okay"; at24@52 { @@ -159,16 +196,102 @@ }; }; +&iomuxc { + imx27_phycore_som { + pinctrl_cspi1: cspi1grp { + fsl,pins = < + MX27_PAD_CSPI1_MISO__CSPI1_MISO 0x0 + MX27_PAD_CSPI1_MOSI__CSPI1_MOSI 0x0 + MX27_PAD_CSPI1_SCLK__CSPI1_SCLK 0x0 + MX27_PAD_CSPI1_SS0__GPIO4_28 0x0 /* SPI1 CS0 */ + MX27_PAD_USB_PWR__GPIO2_23 0x0 /* PMIC IRQ */ + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + MX27_PAD_SD3_CMD__FEC_TXD0 0x0 + MX27_PAD_SD3_CLK__FEC_TXD1 0x0 + MX27_PAD_ATA_DATA0__FEC_TXD2 0x0 + MX27_PAD_ATA_DATA1__FEC_TXD3 0x0 + MX27_PAD_ATA_DATA2__FEC_RX_ER 0x0 + MX27_PAD_ATA_DATA3__FEC_RXD1 0x0 + MX27_PAD_ATA_DATA4__FEC_RXD2 0x0 + MX27_PAD_ATA_DATA5__FEC_RXD3 0x0 + MX27_PAD_ATA_DATA6__FEC_MDIO 0x0 + MX27_PAD_ATA_DATA7__FEC_MDC 0x0 + MX27_PAD_ATA_DATA8__FEC_CRS 0x0 + MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x0 + MX27_PAD_ATA_DATA10__FEC_RXD0 0x0 + MX27_PAD_ATA_DATA11__FEC_RX_DV 0x0 + MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x0 + MX27_PAD_ATA_DATA13__FEC_COL 0x0 + MX27_PAD_ATA_DATA14__FEC_TX_ER 0x0 + MX27_PAD_ATA_DATA15__FEC_TX_EN 0x0 + MX27_PAD_SSI3_TXDAT__GPIO3_30 0x0 /* FEC RST */ + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX27_PAD_I2C2_SDA__I2C2_SDA 0x0 + MX27_PAD_I2C2_SCL__I2C2_SCL 0x0 + >; + }; + + pinctrl_nfc: nfcgrp { + fsl,pins = < + MX27_PAD_NFRB__NFRB 0x0 + MX27_PAD_NFCLE__NFCLE 0x0 + MX27_PAD_NFWP_B__NFWP_B 0x0 + MX27_PAD_NFCE_B__NFCE_B 0x0 + MX27_PAD_NFALE__NFALE 0x0 + MX27_PAD_NFRE_B__NFRE_B 0x0 + MX27_PAD_NFWE_B__NFWE_B 0x0 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX27_PAD_USBOTG_CLK__USBOTG_CLK 0x0 + MX27_PAD_USBOTG_DIR__USBOTG_DIR 0x0 + MX27_PAD_USBOTG_NXT__USBOTG_NXT 0x0 + MX27_PAD_USBOTG_STP__USBOTG_STP 0x0 + MX27_PAD_USBOTG_DATA0__USBOTG_DATA0 0x0 + MX27_PAD_USBOTG_DATA1__USBOTG_DATA1 0x0 + MX27_PAD_USBOTG_DATA2__USBOTG_DATA2 0x0 + MX27_PAD_USBOTG_DATA3__USBOTG_DATA3 0x0 + MX27_PAD_USBOTG_DATA4__USBOTG_DATA4 0x0 + MX27_PAD_USBOTG_DATA5__USBOTG_DATA5 0x0 + MX27_PAD_USBOTG_DATA6__USBOTG_DATA6 0x0 + MX27_PAD_USBOTG_DATA7__USBOTG_DATA7 0x0 + >; + }; + }; +}; + &nfc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nfc>; nand-bus-width = <8>; nand-ecc-mode = "hw"; + nand-on-flash-bbt; status = "okay"; }; -&uart1 { +&usbotg { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + dr_mode = "otg"; + phy_type = "ulpi"; + vbus-supply = <&sw3_reg>; status = "okay"; }; +&usbphy0 { + vcc-supply = <&sw3_reg>; +}; + &weim { status = "okay"; diff --git a/arch/arm/boot/dts/imx27-pinfunc.h b/arch/arm/boot/dts/imx27-pinfunc.h new file mode 100644 index 000000000000..f5387b4de577 --- /dev/null +++ b/arch/arm/boot/dts/imx27-pinfunc.h @@ -0,0 +1,526 @@ +/* + * Copyright 2013 Markus Pargmann <mpa@pengutronix.de>, Pengutronix + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#ifndef __DTS_IMX27_PINFUNC_H +#define __DTS_IMX27_PINFUNC_H + +/* + * The pin function ID is a tuple of + * <pin mux_id> + * mux_id consists of + * function + (direction << 2) + (gpio_oconf << 4) + (gpio_iconfa << 8) + (gpio_iconfb << 10) + * + * function: 0 - Primary function + * 1 - Alternate function + * 2 - GPIO + * direction: 0 - Input + * 1 - Output + * gpio_oconf: 0 - A_IN + * 1 - B_IN + * 2 - C_IN + * 3 - Data Register + * gpio_iconfa/b: 0 - GPIO_IN + * 1 - Interrupt Status Register + * 2 - 0 + * 3 - 1 + * + * 'pin' is an integer between 0 and 0xbf. imx27 has 6 ports with 32 configurable + * configurable pins each. 'pin' is PORT * 32 + PORT_PIN, PORT_PIN is the pin + * number on the specific port (between 0 and 31). + */ + +#define MX27_PAD_USBH2_CLK__USBH2_CLK 0x00 0x000 +#define MX27_PAD_USBH2_CLK__GPIO1_0 0x00 0x032 +#define MX27_PAD_USBH2_DIR__USBH2_DIR 0x01 0x000 +#define MX27_PAD_USBH2_DIR__GPIO1_1 0x01 0x032 +#define MX27_PAD_USBH2_DATA7__USBH2_DATA7 0x02 0x004 +#define MX27_PAD_USBH2_DATA7__GPIO1_2 0x02 0x032 +#define MX27_PAD_USBH2_NXT__USBH2_NXT 0x03 0x000 +#define MX27_PAD_USBH2_NXT__GPIO1_3 0x03 0x032 +#define MX27_PAD_USBH2_STP__USBH2_STP 0x04 0x004 +#define MX27_PAD_USBH2_STP__GPIO1_4 0x04 0x032 +#define MX27_PAD_LSCLK__LSCLK 0x05 0x004 +#define MX27_PAD_LSCLK__GPIO1_5 0x05 0x032 +#define MX27_PAD_LD0__LD0 0x06 0x004 +#define MX27_PAD_LD0__GPIO1_6 0x06 0x032 +#define MX27_PAD_LD1__LD1 0x07 0x004 +#define MX27_PAD_LD1__GPIO1_7 0x07 0x032 +#define MX27_PAD_LD2__LD2 0x08 0x004 +#define MX27_PAD_LD2__GPIO1_8 0x08 0x032 +#define MX27_PAD_LD3__LD3 0x09 0x004 +#define MX27_PAD_LD3__GPIO1_9 0x09 0x032 +#define MX27_PAD_LD4__LD4 0x0a 0x004 +#define MX27_PAD_LD4__GPIO1_10 0x0a 0x032 +#define MX27_PAD_LD5__LD5 0x0b 0x004 +#define MX27_PAD_LD5__GPIO1_11 0x0b 0x032 +#define MX27_PAD_LD6__LD6 0x0c 0x004 +#define MX27_PAD_LD6__GPIO1_12 0x0c 0x032 +#define MX27_PAD_LD7__LD7 0x0d 0x004 +#define MX27_PAD_LD7__GPIO1_13 0x0d 0x032 +#define MX27_PAD_LD8__LD8 0x0e 0x004 +#define MX27_PAD_LD8__GPIO1_14 0x0e 0x032 +#define MX27_PAD_LD9__LD9 0x0f 0x004 +#define MX27_PAD_LD9__GPIO1_15 0x0f 0x032 +#define MX27_PAD_LD10__LD10 0x10 0x004 +#define MX27_PAD_LD10__GPIO1_16 0x10 0x032 +#define MX27_PAD_LD11__LD11 0x11 0x004 +#define MX27_PAD_LD11__GPIO1_17 0x11 0x032 +#define MX27_PAD_LD12__LD12 0x12 0x004 +#define MX27_PAD_LD12__GPIO1_18 0x12 0x032 +#define MX27_PAD_LD13__LD13 0x13 0x004 +#define MX27_PAD_LD13__GPIO1_19 0x13 0x032 +#define MX27_PAD_LD14__LD14 0x14 0x004 +#define MX27_PAD_LD14__GPIO1_20 0x14 0x032 +#define MX27_PAD_LD15__LD15 0x15 0x004 +#define MX27_PAD_LD15__GPIO1_21 0x15 0x032 +#define MX27_PAD_LD16__LD16 0x16 0x004 +#define MX27_PAD_LD16__GPIO1_22 0x16 0x032 +#define MX27_PAD_LD17__LD17 0x17 0x004 +#define MX27_PAD_LD17__GPIO1_23 0x17 0x032 +#define MX27_PAD_REV__REV 0x18 0x004 +#define MX27_PAD_REV__GPIO1_24 0x18 0x032 +#define MX27_PAD_CLS__CLS 0x19 0x004 +#define MX27_PAD_CLS__GPIO1_25 0x19 0x032 +#define MX27_PAD_PS__PS 0x1a 0x004 +#define MX27_PAD_PS__GPIO1_26 0x1a 0x032 +#define MX27_PAD_SPL_SPR__SPL_SPR 0x1b 0x004 +#define MX27_PAD_SPL_SPR__GPIO1_27 0x1b 0x032 +#define MX27_PAD_HSYNC__HSYNC 0x1c 0x004 +#define MX27_PAD_HSYNC__GPIO1_28 0x1c 0x032 +#define MX27_PAD_VSYNC__VSYNC 0x1d 0x004 +#define MX27_PAD_VSYNC__GPIO1_29 0x1d 0x032 +#define MX27_PAD_CONTRAST__CONTRAST 0x1e 0x004 +#define MX27_PAD_CONTRAST__GPIO1_30 0x1e 0x032 +#define MX27_PAD_OE_ACD__OE_ACD 0x1f 0x004 +#define MX27_PAD_OE_ACD__GPIO1_31 0x1f 0x032 +#define MX27_PAD_UNUSED0__UNUSED0 0x20 0x004 +#define MX27_PAD_UNUSED0__GPIO2_0 0x20 0x032 +#define MX27_PAD_UNUSED1__UNUSED1 0x21 0x004 +#define MX27_PAD_UNUSED1__GPIO2_1 0x21 0x032 +#define MX27_PAD_UNUSED2__UNUSED2 0x22 0x004 +#define MX27_PAD_UNUSED2__GPIO2_2 0x22 0x032 +#define MX27_PAD_UNUSED3__UNUSED3 0x23 0x004 +#define MX27_PAD_UNUSED3__GPIO2_3 0x23 0x032 +#define MX27_PAD_SD2_D0__SD2_D0 0x24 0x004 +#define MX27_PAD_SD2_D0__MSHC_DATA0 0x24 0x005 +#define MX27_PAD_SD2_D0__GPIO2_4 0x24 0x032 +#define MX27_PAD_SD2_D1__SD2_D1 0x25 0x004 +#define MX27_PAD_SD2_D1__MSHC_DATA1 0x25 0x005 +#define MX27_PAD_SD2_D1__GPIO2_5 0x25 0x032 +#define MX27_PAD_SD2_D2__SD2_D2 0x26 0x004 +#define MX27_PAD_SD2_D2__MSHC_DATA2 0x26 0x005 +#define MX27_PAD_SD2_D2__GPIO2_6 0x26 0x032 +#define MX27_PAD_SD2_D3__SD2_D3 0x27 0x004 +#define MX27_PAD_SD2_D3__MSHC_DATA3 0x27 0x005 +#define MX27_PAD_SD2_D3__GPIO2_7 0x27 0x032 +#define MX27_PAD_SD2_CMD__SD2_CMD 0x28 0x004 +#define MX27_PAD_SD2_CMD__MSHC_BS 0x28 0x005 +#define MX27_PAD_SD2_CMD__GPIO2_8 0x28 0x032 +#define MX27_PAD_SD2_CLK__SD2_CLK 0x29 0x004 +#define MX27_PAD_SD2_CLK__MSHC_SCLK 0x29 0x005 +#define MX27_PAD_SD2_CLK__GPIO2_9 0x29 0x032 +#define MX27_PAD_CSI_D0__CSI_D0 0x2a 0x000 +#define MX27_PAD_CSI_D0__UART6_TXD 0x2a 0x005 +#define MX27_PAD_CSI_D0__GPIO2_10 0x2a 0x032 +#define MX27_PAD_CSI_D1__CSI_D1 0x2b 0x000 +#define MX27_PAD_CSI_D1__UART6_RXD 0x2b 0x001 +#define MX27_PAD_CSI_D1__GPIO2_11 0x2b 0x032 +#define MX27_PAD_CSI_D2__CSI_D2 0x2c 0x000 +#define MX27_PAD_CSI_D2__UART6_CTS 0x2c 0x005 +#define MX27_PAD_CSI_D2__GPIO2_12 0x2c 0x032 +#define MX27_PAD_CSI_D3__CSI_D3 0x2d 0x000 +#define MX27_PAD_CSI_D3__UART6_RTS 0x2d 0x001 +#define MX27_PAD_CSI_D3__GPIO2_13 0x2d 0x032 +#define MX27_PAD_CSI_D4__CSI_D4 0x2e 0x000 +#define MX27_PAD_CSI_D4__GPIO2_14 0x2e 0x032 +#define MX27_PAD_CSI_MCLK__CSI_MCLK 0x2f 0x004 +#define MX27_PAD_CSI_MCLK__GPIO2_15 0x2f 0x032 +#define MX27_PAD_CSI_PIXCLK__CSI_PIXCLK 0x30 0x000 +#define MX27_PAD_CSI_PIXCLK__GPIO2_16 0x30 0x032 +#define MX27_PAD_CSI_D5__CSI_D5 0x31 0x000 +#define MX27_PAD_CSI_D5__GPIO2_17 0x31 0x032 +#define MX27_PAD_CSI_D6__CSI_D6 0x32 0x000 +#define MX27_PAD_CSI_D6__UART5_TXD 0x32 0x005 +#define MX27_PAD_CSI_D6__GPIO2_18 0x32 0x032 +#define MX27_PAD_CSI_D7__CSI_D7 0x33 0x000 +#define MX27_PAD_CSI_D7__UART5_RXD 0x33 0x001 +#define MX27_PAD_CSI_D7__GPIO2_19 0x33 0x032 +#define MX27_PAD_CSI_VSYNC__CSI_VSYNC 0x34 0x000 +#define MX27_PAD_CSI_VSYNC__UART5_CTS 0x34 0x005 +#define MX27_PAD_CSI_VSYNC__GPIO2_20 0x34 0x032 +#define MX27_PAD_CSI_HSYNC__CSI_HSYNC 0x35 0x000 +#define MX27_PAD_CSI_HSYNC__UART5_RTS 0x35 0x001 +#define MX27_PAD_CSI_HSYNC__GPIO2_21 0x35 0x032 +#define MX27_PAD_USBH1_SUSP__USBH1_SUSP 0x36 0x004 +#define MX27_PAD_USBH1_SUSP__GPIO2_22 0x36 0x032 +#define MX27_PAD_USB_PWR__USB_PWR 0x37 0x004 +#define MX27_PAD_USB_PWR__GPIO2_23 0x37 0x032 +#define MX27_PAD_USB_OC_B__USB_OC_B 0x38 0x000 +#define MX27_PAD_USB_OC_B__GPIO2_24 0x38 0x032 +#define MX27_PAD_USBH1_RCV__USBH1_RCV 0x39 0x004 +#define MX27_PAD_USBH1_RCV__GPIO2_25 0x39 0x032 +#define MX27_PAD_USBH1_FS__USBH1_FS 0x3a 0x004 +#define MX27_PAD_USBH1_FS__UART4_RTS 0x3a 0x001 +#define MX27_PAD_USBH1_FS__GPIO2_26 0x3a 0x032 +#define MX27_PAD_USBH1_OE_B__USBH1_OE_B 0x3b 0x004 +#define MX27_PAD_USBH1_OE_B__GPIO2_27 0x3b 0x032 +#define MX27_PAD_USBH1_TXDM__USBH1_TXDM 0x3c 0x004 +#define MX27_PAD_USBH1_TXDM__UART4_TXD 0x3c 0x005 +#define MX27_PAD_USBH1_TXDM__GPIO2_28 0x3c 0x032 +#define MX27_PAD_USBH1_TXDP__USBH1_TXDP 0x3d 0x004 +#define MX27_PAD_USBH1_TXDP__UART4_CTS 0x3d 0x005 +#define MX27_PAD_USBH1_TXDP__GPIO2_29 0x3d 0x032 +#define MX27_PAD_USBH1_RXDM__USBH1_RXDM 0x3e 0x004 +#define MX27_PAD_USBH1_RXDM__GPIO2_30 0x3e 0x032 +#define MX27_PAD_USBH1_RXDP__USBH1_RXDP 0x3f 0x004 +#define MX27_PAD_USBH1_RXDP__UART4_RXD 0x3f 0x001 +#define MX27_PAD_USBH1_RXDP__GPIO2_31 0x3f 0x032 +#define MX27_PAD_UNUSED4__UNUSED4 0x40 0x004 +#define MX27_PAD_UNUSED4__GPIO3_0 0x40 0x032 +#define MX27_PAD_UNUSED5__UNUSED5 0x41 0x004 +#define MX27_PAD_UNUSED5__GPIO3_1 0x41 0x032 +#define MX27_PAD_UNUSED6__UNUSED6 0x42 0x004 +#define MX27_PAD_UNUSED6__GPIO3_2 0x42 0x032 +#define MX27_PAD_UNUSED7__UNUSED7 0x43 0x004 +#define MX27_PAD_UNUSED7__GPIO3_3 0x43 0x032 +#define MX27_PAD_UNUSED8__UNUSED8 0x44 0x004 +#define MX27_PAD_UNUSED8__GPIO3_4 0x44 0x032 +#define MX27_PAD_I2C2_SDA__I2C2_SDA 0x45 0x004 +#define MX27_PAD_I2C2_SDA__GPIO3_5 0x45 0x032 +#define MX27_PAD_I2C2_SCL__I2C2_SCL 0x46 0x004 +#define MX27_PAD_I2C2_SCL__GPIO3_6 0x46 0x032 +#define MX27_PAD_USBOTG_DATA5__USBOTG_DATA5 0x47 0x004 +#define MX27_PAD_USBOTG_DATA5__GPIO3_7 0x47 0x032 +#define MX27_PAD_USBOTG_DATA6__USBOTG_DATA6 0x48 0x004 +#define MX27_PAD_USBOTG_DATA6__GPIO3_8 0x48 0x032 +#define MX27_PAD_USBOTG_DATA0__USBOTG_DATA0 0x49 0x004 +#define MX27_PAD_USBOTG_DATA0__GPIO3_9 0x49 0x032 +#define MX27_PAD_USBOTG_DATA2__USBOTG_DATA2 0x4a 0x004 +#define MX27_PAD_USBOTG_DATA2__GPIO3_10 0x4a 0x032 +#define MX27_PAD_USBOTG_DATA1__USBOTG_DATA1 0x4b 0x004 +#define MX27_PAD_USBOTG_DATA1__GPIO3_11 0x4b 0x032 +#define MX27_PAD_USBOTG_DATA4__USBOTG_DATA4 0x4c 0x004 +#define MX27_PAD_USBOTG_DATA4__GPIO3_12 0x4c 0x032 +#define MX27_PAD_USBOTG_DATA3__USBOTG_DATA3 0x4d 0x004 +#define MX27_PAD_USBOTG_DATA3__GPIO3_13 0x4d 0x032 +#define MX27_PAD_TOUT__TOUT 0x4e 0x004 +#define MX27_PAD_TOUT__GPIO3_14 0x4e 0x032 +#define MX27_PAD_TIN__TIN 0x4f 0x000 +#define MX27_PAD_TIN__GPIO3_15 0x4f 0x032 +#define MX27_PAD_SSI4_FS__SSI4_FS 0x50 0x004 +#define MX27_PAD_SSI4_FS__GPIO3_16 0x50 0x032 +#define MX27_PAD_SSI4_RXDAT__SSI4_RXDAT 0x51 0x004 +#define MX27_PAD_SSI4_RXDAT__GPIO3_17 0x51 0x032 +#define MX27_PAD_SSI4_TXDAT__SSI4_TXDAT 0x52 0x004 +#define MX27_PAD_SSI4_TXDAT__GPIO3_18 0x52 0x032 +#define MX27_PAD_SSI4_CLK__SSI4_CLK 0x53 0x004 +#define MX27_PAD_SSI4_CLK__GPIO3_19 0x53 0x032 +#define MX27_PAD_SSI1_FS__SSI1_FS 0x54 0x004 +#define MX27_PAD_SSI1_FS__GPIO3_20 0x54 0x032 +#define MX27_PAD_SSI1_RXDAT__SSI1_RXDAT 0x55 0x004 +#define MX27_PAD_SSI1_RXDAT__GPIO3_21 0x55 0x032 +#define MX27_PAD_SSI1_TXDAT__SSI1_TXDAT 0x56 0x004 +#define MX27_PAD_SSI1_TXDAT__GPIO3_22 0x56 0x032 +#define MX27_PAD_SSI1_CLK__SSI1_CLK 0x57 0x004 +#define MX27_PAD_SSI1_CLK__GPIO3_23 0x57 0x032 +#define MX27_PAD_SSI2_FS__SSI2_FS 0x58 0x004 +#define MX27_PAD_SSI2_FS__GPT5_TOUT 0x58 0x005 +#define MX27_PAD_SSI2_FS__GPIO3_24 0x58 0x032 +#define MX27_PAD_SSI2_RXDAT__SSI2_RXDAT 0x59 0x004 +#define MX27_PAD_SSI2_RXDAT__GPTS_TIN 0x59 0x001 +#define MX27_PAD_SSI2_RXDAT__GPIO3_25 0x59 0x032 +#define MX27_PAD_SSI2_TXDAT__SSI2_TXDAT 0x5a 0x004 +#define MX27_PAD_SSI2_TXDAT__GPT4_TOUT 0x5a 0x005 +#define MX27_PAD_SSI2_TXDAT__GPIO3_26 0x5a 0x032 +#define MX27_PAD_SSI2_CLK__SSI2_CLK 0x5b 0x004 +#define MX27_PAD_SSI2_CLK__GPT4_TIN 0x5b 0x001 +#define MX27_PAD_SSI2_CLK__GPIO3_27 0x5b 0x032 +#define MX27_PAD_SSI3_FS__SSI3_FS 0x5c 0x004 +#define MX27_PAD_SSI3_FS__SLCDC2_D0 0x5c 0x001 +#define MX27_PAD_SSI3_FS__GPIO3_28 0x5c 0x032 +#define MX27_PAD_SSI3_RXDAT__SSI3_RXDAT 0x5d 0x004 +#define MX27_PAD_SSI3_RXDAT__SLCDC2_RS 0x5d 0x001 +#define MX27_PAD_SSI3_RXDAT__GPIO3_29 0x5d 0x032 +#define MX27_PAD_SSI3_TXDAT__SSI3_TXDAT 0x5e 0x004 +#define MX27_PAD_SSI3_TXDAT__SLCDC2_CS 0x5e 0x001 +#define MX27_PAD_SSI3_TXDAT__GPIO3_30 0x5e 0x032 +#define MX27_PAD_SSI3_CLK__SSI3_CLK 0x5f 0x004 +#define MX27_PAD_SSI3_CLK__SLCDC2_CLK 0x5f 0x001 +#define MX27_PAD_SSI3_CLK__GPIO3_31 0x5f 0x032 +#define MX27_PAD_SD3_CMD__SD3_CMD 0x60 0x004 +#define MX27_PAD_SD3_CMD__FEC_TXD0 0x60 0x006 +#define MX27_PAD_SD3_CMD__GPIO4_0 0x60 0x032 +#define MX27_PAD_SD3_CLK__SD3_CLK 0x61 0x004 +#define MX27_PAD_SD3_CLK__ETMTRACEPKT15 0x61 0x005 +#define MX27_PAD_SD3_CLK__FEC_TXD1 0x61 0x006 +#define MX27_PAD_SD3_CLK__GPIO4_1 0x61 0x032 +#define MX27_PAD_ATA_DATA0__ATA_DATA0 0x62 0x004 +#define MX27_PAD_ATA_DATA0__SD3_D0 0x62 0x005 +#define MX27_PAD_ATA_DATA0__FEC_TXD2 0x62 0x006 +#define MX27_PAD_ATA_DATA0__GPIO4_2 0x62 0x032 +#define MX27_PAD_ATA_DATA1__ATA_DATA1 0x63 0x004 +#define MX27_PAD_ATA_DATA1__SD3_D1 0x63 0x005 +#define MX27_PAD_ATA_DATA1__FEC_TXD3 0x63 0x006 +#define MX27_PAD_ATA_DATA1__GPIO4_3 0x63 0x032 +#define MX27_PAD_ATA_DATA2__ATA_DATA2 0x64 0x004 +#define MX27_PAD_ATA_DATA2__SD3_D2 0x64 0x005 +#define MX27_PAD_ATA_DATA2__FEC_RX_ER 0x64 0x002 +#define MX27_PAD_ATA_DATA2__GPIO4_4 0x64 0x032 +#define MX27_PAD_ATA_DATA3__ATA_DATA3 0x65 0x004 +#define MX27_PAD_ATA_DATA3__SD3_D3 0x65 0x005 +#define MX27_PAD_ATA_DATA3__FEC_RXD1 0x65 0x002 +#define MX27_PAD_ATA_DATA3__GPIO4_5 0x65 0x032 +#define MX27_PAD_ATA_DATA4__ATA_DATA4 0x66 0x004 +#define MX27_PAD_ATA_DATA4__ETMTRACEPKT14 0x66 0x005 +#define MX27_PAD_ATA_DATA4__FEC_RXD2 0x66 0x002 +#define MX27_PAD_ATA_DATA4__GPIO4_6 0x66 0x032 +#define MX27_PAD_ATA_DATA5__ATA_DATA5 0x67 0x004 +#define MX27_PAD_ATA_DATA5__ETMTRACEPKT13 0x67 0x005 +#define MX27_PAD_ATA_DATA5__FEC_RXD3 0x67 0x002 +#define MX27_PAD_ATA_DATA5__GPIO4_7 0x67 0x032 +#define MX27_PAD_ATA_DATA6__ATA_DATA6 0x68 0x004 +#define MX27_PAD_ATA_DATA6__FEC_MDIO 0x68 0x005 +#define MX27_PAD_ATA_DATA6__GPIO4_8 0x68 0x032 +#define MX27_PAD_ATA_DATA7__ATA_DATA7 0x69 0x004 +#define MX27_PAD_ATA_DATA7__ETMTRACEPKT12 0x69 0x005 +#define MX27_PAD_ATA_DATA7__FEC_MDC 0x69 0x006 +#define MX27_PAD_ATA_DATA7__GPIO4_9 0x69 0x032 +#define MX27_PAD_ATA_DATA8__ATA_DATA8 0x6a 0x004 +#define MX27_PAD_ATA_DATA8__ETMTRACEPKT11 0x6a 0x005 +#define MX27_PAD_ATA_DATA8__FEC_CRS 0x6a 0x002 +#define MX27_PAD_ATA_DATA8__GPIO4_10 0x6a 0x032 +#define MX27_PAD_ATA_DATA9__ATA_DATA9 0x6b 0x004 +#define MX27_PAD_ATA_DATA9__ETMTRACEPKT10 0x6b 0x005 +#define MX27_PAD_ATA_DATA9__FEC_TX_CLK 0x6b 0x002 +#define MX27_PAD_ATA_DATA9__GPIO4_11 0x6b 0x032 +#define MX27_PAD_ATA_DATA10__ATA_DATA10 0x6c 0x004 +#define MX27_PAD_ATA_DATA10__ETMTRACEPKT9 0x6c 0x005 +#define MX27_PAD_ATA_DATA10__FEC_RXD0 0x6c 0x002 +#define MX27_PAD_ATA_DATA10__GPIO4_12 0x6c 0x032 +#define MX27_PAD_ATA_DATA11__ATA_DATA11 0x6d 0x004 +#define MX27_PAD_ATA_DATA11__ETMTRACEPKT8 0x6d 0x005 +#define MX27_PAD_ATA_DATA11__FEC_RX_DV 0x6d 0x002 +#define MX27_PAD_ATA_DATA11__GPIO4_13 0x6d 0x032 +#define MX27_PAD_ATA_DATA12__ATA_DATA12 0x6e 0x004 +#define MX27_PAD_ATA_DATA12__ETMTRACEPKT7 0x6e 0x005 +#define MX27_PAD_ATA_DATA12__FEC_RX_CLK 0x6e 0x002 +#define MX27_PAD_ATA_DATA12__GPIO4_14 0x6e 0x032 +#define MX27_PAD_ATA_DATA13__ATA_DATA13 0x6f 0x004 +#define MX27_PAD_ATA_DATA13__ETMTRACEPKT6 0x6f 0x005 +#define MX27_PAD_ATA_DATA13__FEC_COL 0x6f 0x002 +#define MX27_PAD_ATA_DATA13__GPIO4_15 0x6f 0x032 +#define MX27_PAD_ATA_DATA14__ATA_DATA14 0x70 0x004 +#define MX27_PAD_ATA_DATA14__ETMTRACEPKT5 0x70 0x005 +#define MX27_PAD_ATA_DATA14__FEC_TX_ER 0x70 0x006 +#define MX27_PAD_ATA_DATA14__GPIO4_16 0x70 0x032 +#define MX27_PAD_I2C_DATA__I2C_DATA 0x71 0x004 +#define MX27_PAD_I2C_DATA__GPIO4_17 0x71 0x032 +#define MX27_PAD_I2C_CLK__I2C_CLK 0x72 0x004 +#define MX27_PAD_I2C_CLK__GPIO4_18 0x72 0x032 +#define MX27_PAD_CSPI2_SS2__CSPI2_SS2 0x73 0x004 +#define MX27_PAD_CSPI2_SS2__USBH2_DATA4 0x73 0x005 +#define MX27_PAD_CSPI2_SS2__GPIO4_19 0x73 0x032 +#define MX27_PAD_CSPI2_SS1__CSPI2_SS1 0x74 0x004 +#define MX27_PAD_CSPI2_SS1__USBH2_DATA3 0x74 0x005 +#define MX27_PAD_CSPI2_SS1__GPIO4_20 0x74 0x032 +#define MX27_PAD_CSPI2_SS0__CSPI2_SS0 0x75 0x004 +#define MX27_PAD_CSPI2_SS0__USBH2_DATA6 0x75 0x005 +#define MX27_PAD_CSPI2_SS0__GPIO4_21 0x75 0x032 +#define MX27_PAD_CSPI2_SCLK__CSPI2_SCLK 0x76 0x004 +#define MX27_PAD_CSPI2_SCLK__USBH2_DATA0 0x76 0x005 +#define MX27_PAD_CSPI2_SCLK__GPIO4_22 0x76 0x032 +#define MX27_PAD_CSPI2_MISO__CSPI2_MISO 0x77 0x004 +#define MX27_PAD_CSPI2_MISO__USBH2_DATA2 0x77 0x005 +#define MX27_PAD_CSPI2_MISO__GPIO4_23 0x77 0x032 +#define MX27_PAD_CSPI2_MOSI__CSPI2_MOSI 0x78 0x004 +#define MX27_PAD_CSPI2_MOSI__USBH2_DATA1 0x78 0x005 +#define MX27_PAD_CSPI2_MOSI__GPIO4_24 0x78 0x032 +#define MX27_PAD_CSPI1_RDY__CSPI1_RDY 0x79 0x000 +#define MX27_PAD_CSPI1_RDY__GPIO4_25 0x79 0x032 +#define MX27_PAD_CSPI1_SS2__CSPI1_SS2 0x7a 0x004 +#define MX27_PAD_CSPI1_SS2__USBH2_DATA5 0x7a 0x005 +#define MX27_PAD_CSPI1_SS2__GPIO4_26 0x7a 0x032 +#define MX27_PAD_CSPI1_SS1__CSPI1_SS1 0x7b 0x004 +#define MX27_PAD_CSPI1_SS1__GPIO4_27 0x7b 0x032 +#define MX27_PAD_CSPI1_SS0__CSPI1_SS0 0x7c 0x004 +#define MX27_PAD_CSPI1_SS0__GPIO4_28 0x7c 0x032 +#define MX27_PAD_CSPI1_SCLK__CSPI1_SCLK 0x7d 0x004 +#define MX27_PAD_CSPI1_SCLK__GPIO4_29 0x7d 0x032 +#define MX27_PAD_CSPI1_MISO__CSPI1_MISO 0x7e 0x004 +#define MX27_PAD_CSPI1_MISO__GPIO4_30 0x7e 0x032 +#define MX27_PAD_CSPI1_MOSI__CSPI1_MOSI 0x7f 0x004 +#define MX27_PAD_CSPI1_MOSI__GPIO4_31 0x7f 0x032 +#define MX27_PAD_USBOTG_NXT__USBOTG_NXT 0x80 0x000 +#define MX27_PAD_USBOTG_NXT__KP_COL6A 0x80 0x005 +#define MX27_PAD_USBOTG_NXT__GPIO5_0 0x80 0x032 +#define MX27_PAD_USBOTG_STP__USBOTG_STP 0x81 0x004 +#define MX27_PAD_USBOTG_STP__KP_ROW6A 0x81 0x005 +#define MX27_PAD_USBOTG_STP__GPIO5_1 0x81 0x032 +#define MX27_PAD_USBOTG_DIR__USBOTG_DIR 0x82 0x000 +#define MX27_PAD_USBOTG_DIR__KP_ROW7A 0x82 0x005 +#define MX27_PAD_USBOTG_DIR__GPIO5_2 0x82 0x032 +#define MX27_PAD_UART2_CTS__UART2_CTS 0x83 0x004 +#define MX27_PAD_UART2_CTS__KP_COL7 0x83 0x005 +#define MX27_PAD_UART2_CTS__GPIO5_3 0x83 0x032 +#define MX27_PAD_UART2_RTS__UART2_RTS 0x84 0x000 +#define MX27_PAD_UART2_RTS__KP_ROW7 0x84 0x005 +#define MX27_PAD_UART2_RTS__GPIO5_4 0x84 0x032 +#define MX27_PAD_PWMO__PWMO 0x85 0x004 +#define MX27_PAD_PWMO__GPIO5_5 0x85 0x032 +#define MX27_PAD_UART2_TXD__UART2_TXD 0x86 0x004 +#define MX27_PAD_UART2_TXD__KP_COL6 0x86 0x005 +#define MX27_PAD_UART2_TXD__GPIO5_6 0x86 0x032 +#define MX27_PAD_UART2_RXD__UART2_RXD 0x87 0x000 +#define MX27_PAD_UART2_RXD__KP_ROW6 0x87 0x005 +#define MX27_PAD_UART2_RXD__GPIO5_7 0x87 0x032 +#define MX27_PAD_UART3_TXD__UART3_TXD 0x88 0x004 +#define MX27_PAD_UART3_TXD__GPIO5_8 0x88 0x032 +#define MX27_PAD_UART3_RXD__UART3_RXD 0x89 0x000 +#define MX27_PAD_UART3_RXD__GPIO5_9 0x89 0x032 +#define MX27_PAD_UART3_CTS__UART3_CTS 0x8a 0x004 +#define MX27_PAD_UART3_CTS__GPIO5_10 0x8a 0x032 +#define MX27_PAD_UART3_RTS__UART3_RTS 0x8b 0x000 +#define MX27_PAD_UART3_RTS__GPIO5_11 0x8b 0x032 +#define MX27_PAD_UART1_TXD__UART1_TXD 0x8c 0x004 +#define MX27_PAD_UART1_TXD__GPIO5_12 0x8c 0x032 +#define MX27_PAD_UART1_RXD__UART1_RXD 0x8d 0x000 +#define MX27_PAD_UART1_RXD__GPIO5_13 0x8d 0x032 +#define MX27_PAD_UART1_CTS__UART1_CTS 0x8e 0x004 +#define MX27_PAD_UART1_CTS__GPIO5_14 0x8e 0x032 +#define MX27_PAD_UART1_RTS__UART1_RTS 0x8f 0x000 +#define MX27_PAD_UART1_RTS__GPIO5_15 0x8f 0x032 +#define MX27_PAD_RTCK__RTCK 0x90 0x004 +#define MX27_PAD_RTCK__OWIRE 0x90 0x005 +#define MX27_PAD_RTCK__GPIO5_16 0x90 0x032 +#define MX27_PAD_RESET_OUT_B__RESET_OUT_B 0x91 0x004 +#define MX27_PAD_RESET_OUT_B__GPIO5_17 0x91 0x032 +#define MX27_PAD_SD1_D0__SD1_D0 0x92 0x004 +#define MX27_PAD_SD1_D0__CSPI3_MISO 0x92 0x001 +#define MX27_PAD_SD1_D0__GPIO5_18 0x92 0x032 +#define MX27_PAD_SD1_D1__SD1_D1 0x93 0x004 +#define MX27_PAD_SD1_D1__GPIO5_19 0x93 0x032 +#define MX27_PAD_SD1_D2__SD1_D2 0x94 0x004 +#define MX27_PAD_SD1_D2__GPIO5_20 0x94 0x032 +#define MX27_PAD_SD1_D3__SD1_D3 0x95 0x004 +#define MX27_PAD_SD1_D3__CSPI3_SS 0x95 0x005 +#define MX27_PAD_SD1_D3__GPIO5_21 0x95 0x032 +#define MX27_PAD_SD1_CMD__SD1_CMD 0x96 0x004 +#define MX27_PAD_SD1_CMD__CSPI3_MOSI 0x96 0x005 +#define MX27_PAD_SD1_CMD__GPIO5_22 0x96 0x032 +#define MX27_PAD_SD1_CLK__SD1_CLK 0x97 0x004 +#define MX27_PAD_SD1_CLK__CSPI3_SCLK 0x97 0x005 +#define MX27_PAD_SD1_CLK__GPIO5_23 0x97 0x032 +#define MX27_PAD_USBOTG_CLK__USBOTG_CLK 0x98 0x000 +#define MX27_PAD_USBOTG_CLK__GPIO5_24 0x98 0x032 +#define MX27_PAD_USBOTG_DATA7__USBOTG_DATA7 0x99 0x004 +#define MX27_PAD_USBOTG_DATA7__GPIO5_25 0x99 0x032 +#define MX27_PAD_UNUSED9__UNUSED9 0x9a 0x004 +#define MX27_PAD_UNUSED9__GPIO5_26 0x9a 0x032 +#define MX27_PAD_UNUSED10__UNUSED10 0x9b 0x004 +#define MX27_PAD_UNUSED10__GPIO5_27 0x9b 0x032 +#define MX27_PAD_UNUSED11__UNUSED11 0x9c 0x004 +#define MX27_PAD_UNUSED11__GPIO5_28 0x9c 0x032 +#define MX27_PAD_UNUSED12__UNUSED12 0x9d 0x004 +#define MX27_PAD_UNUSED12__GPIO5_29 0x9d 0x032 +#define MX27_PAD_UNUSED13__UNUSED13 0x9e 0x004 +#define MX27_PAD_UNUSED13__GPIO5_30 0x9e 0x032 +#define MX27_PAD_UNUSED14__UNUSED14 0x9f 0x004 +#define MX27_PAD_UNUSED14__GPIO5_31 0x9f 0x032 +#define MX27_PAD_NFRB__NFRB 0xa0 0x000 +#define MX27_PAD_NFRB__ETMTRACEPKT3 0xa0 0x005 +#define MX27_PAD_NFRB__GPIO6_0 0xa0 0x032 +#define MX27_PAD_NFCLE__NFCLE 0xa1 0x004 +#define MX27_PAD_NFCLE__ETMTRACEPKT0 0xa1 0x005 +#define MX27_PAD_NFCLE__GPIO6_1 0xa1 0x032 +#define MX27_PAD_NFWP_B__NFWP_B 0xa2 0x004 +#define MX27_PAD_NFWP_B__ETMTRACEPKT1 0xa2 0x005 +#define MX27_PAD_NFWP_B__GPIO6_2 0xa2 0x032 +#define MX27_PAD_NFCE_B__NFCE_B 0xa3 0x004 +#define MX27_PAD_NFCE_B__ETMTRACEPKT2 0xa3 0x005 +#define MX27_PAD_NFCE_B__GPIO6_3 0xa3 0x032 +#define MX27_PAD_NFALE__NFALE 0xa4 0x004 +#define MX27_PAD_NFALE__ETMPIPESTAT0 0xa4 0x005 +#define MX27_PAD_NFALE__GPIO6_4 0xa4 0x032 +#define MX27_PAD_NFRE_B__NFRE_B 0xa5 0x004 +#define MX27_PAD_NFRE_B__ETMPIPESTAT1 0xa5 0x005 +#define MX27_PAD_NFRE_B__GPIO6_5 0xa5 0x032 +#define MX27_PAD_NFWE_B__NFWE_B 0xa6 0x004 +#define MX27_PAD_NFWE_B__ETMPIPESTAT2 0xa6 0x005 +#define MX27_PAD_NFWE_B__GPIO6_6 0xa6 0x032 +#define MX27_PAD_PC_POE__PC_POE 0xa7 0x004 +#define MX27_PAD_PC_POE__ATA_BUFFER_EN 0xa7 0x005 +#define MX27_PAD_PC_POE__GPIO6_7 0xa7 0x032 +#define MX27_PAD_PC_RW_B__PC_RW_B 0xa8 0x004 +#define MX27_PAD_PC_RW_B__ATA_IORDY 0xa8 0x001 +#define MX27_PAD_PC_RW_B__GPIO6_8 0xa8 0x032 +#define MX27_PAD_IOIS16__IOIS16 0xa9 0x000 +#define MX27_PAD_IOIS16__ATA_INTRQ 0xa9 0x001 +#define MX27_PAD_IOIS16__GPIO6_9 0xa9 0x032 +#define MX27_PAD_PC_RST__PC_RST 0xaa 0x004 +#define MX27_PAD_PC_RST__ATA_RESET_B 0xaa 0x005 +#define MX27_PAD_PC_RST__GPIO6_10 0xaa 0x032 +#define MX27_PAD_PC_BVD2__PC_BVD2 0xab 0x000 +#define MX27_PAD_PC_BVD2__ATA_DMACK 0xab 0x005 +#define MX27_PAD_PC_BVD2__GPIO6_11 0xab 0x032 +#define MX27_PAD_PC_BVD1__PC_BVD1 0xac 0x000 +#define MX27_PAD_PC_BVD1__ATA_DMARQ 0xac 0x001 +#define MX27_PAD_PC_BVD1__GPIO6_12 0xac 0x032 +#define MX27_PAD_PC_VS2__PC_VS2 0xad 0x000 +#define MX27_PAD_PC_VS2__ATA_DA0 0xad 0x005 +#define MX27_PAD_PC_VS2__GPIO6_13 0xad 0x032 +#define MX27_PAD_PC_VS1__PC_VS1 0xae 0x000 +#define MX27_PAD_PC_VS1__ATA_DA1 0xae 0x005 +#define MX27_PAD_PC_VS1__GPIO6_14 0xae 0x032 +#define MX27_PAD_CLKO__CLKO 0xaf 0x004 +#define MX27_PAD_CLKO__GPIO6_15 0xaf 0x032 +#define MX27_PAD_PC_PWRON__PC_PWRON 0xb0 0x000 +#define MX27_PAD_PC_PWRON__ATA_DA2 0xb0 0x005 +#define MX27_PAD_PC_PWRON__GPIO6_16 0xb0 0x032 +#define MX27_PAD_PC_READY__PC_READY 0xb1 0x000 +#define MX27_PAD_PC_READY__ATA_CS0 0xb1 0x005 +#define MX27_PAD_PC_READY__GPIO6_17 0xb1 0x032 +#define MX27_PAD_PC_WAIT_B__PC_WAIT_B 0xb2 0x000 +#define MX27_PAD_PC_WAIT_B__ATA_CS1 0xb2 0x005 +#define MX27_PAD_PC_WAIT_B__GPIO6_18 0xb2 0x032 +#define MX27_PAD_PC_CD2_B__PC_CD2_B 0xb3 0x000 +#define MX27_PAD_PC_CD2_B__ATA_DIOW 0xb3 0x005 +#define MX27_PAD_PC_CD2_B__GPIO6_19 0xb3 0x032 +#define MX27_PAD_PC_CD1_B__PC_CD1_B 0xb4 0x000 +#define MX27_PAD_PC_CD1_B__ATA_DIOR 0xb4 0x005 +#define MX27_PAD_PC_CD1_B__GPIO6_20 0xb4 0x032 +#define MX27_PAD_CS4_B__CS4_B 0xb5 0x004 +#define MX27_PAD_CS4_B__ETMTRACESYNC 0xb5 0x005 +#define MX27_PAD_CS4_B__GPIO6_21 0xb5 0x032 +#define MX27_PAD_CS5_B__CS5_B 0xb6 0x004 +#define MX27_PAD_CS5_B__ETMTRACECLK 0xb6 0x005 +#define MX27_PAD_CS5_B__GPIO6_22 0xb6 0x032 +#define MX27_PAD_ATA_DATA15__ATA_DATA15 0xb7 0x004 +#define MX27_PAD_ATA_DATA15__ETMTRACEPKT4 0xb7 0x005 +#define MX27_PAD_ATA_DATA15__FEC_TX_EN 0xb7 0x006 +#define MX27_PAD_ATA_DATA15__GPIO6_23 0xb7 0x032 +#define MX27_PAD_UNUSED15__UNUSED15 0xb8 0x004 +#define MX27_PAD_UNUSED15__GPIO6_24 0xb8 0x032 +#define MX27_PAD_UNUSED16__UNUSED16 0xb9 0x004 +#define MX27_PAD_UNUSED16__GPIO6_25 0xb9 0x032 +#define MX27_PAD_UNUSED17__UNUSED17 0xba 0x004 +#define MX27_PAD_UNUSED17__GPIO6_26 0xba 0x032 +#define MX27_PAD_UNUSED18__UNUSED18 0xbb 0x004 +#define MX27_PAD_UNUSED18__GPIO6_27 0xbb 0x032 +#define MX27_PAD_UNUSED19__UNUSED19 0xbc 0x004 +#define MX27_PAD_UNUSED19__GPIO6_28 0xbc 0x032 +#define MX27_PAD_UNUSED20__UNUSED20 0xbd 0x004 +#define MX27_PAD_UNUSED20__GPIO6_29 0xbd 0x032 +#define MX27_PAD_UNUSED21__UNUSED21 0xbe 0x004 +#define MX27_PAD_UNUSED21__GPIO6_30 0xbe 0x032 +#define MX27_PAD_UNUSED22__UNUSED22 0xbf 0x004 +#define MX27_PAD_UNUSED22__GPIO6_31 0xbf 0x032 + +#endif /* __DTS_IMX27_PINFUNC_H */ diff --git a/arch/arm/boot/dts/imx27.dtsi b/arch/arm/boot/dts/imx27.dtsi index 826231eb4446..6279e0b4f768 100644 --- a/arch/arm/boot/dts/imx27.dtsi +++ b/arch/arm/boot/dts/imx27.dtsi @@ -10,6 +10,9 @@ */ #include "skeleton.dtsi" +#include "imx27-pinfunc.h" +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/gpio/gpio.h> / { aliases { @@ -67,6 +70,26 @@ }; }; + usbphy { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + usbphy0: usbphy@0 { + compatible = "usb-nop-xceiv"; + reg = <0>; + clocks = <&clks 75>; + clock-names = "main_clk"; + }; + + usbphy2: usbphy@2 { + compatible = "usb-nop-xceiv"; + reg = <2>; + clocks = <&clks 75>; + clock-names = "main_clk"; + }; + }; + soc { #address-cells = <1>; #size-cells = <1>; @@ -204,6 +227,30 @@ status = "disabled"; }; + ssi1: ssi@10010000 { + #sound-dai-cells = <0>; + compatible = "fsl,imx27-ssi", "fsl,imx21-ssi"; + reg = <0x10010000 0x1000>; + interrupts = <14>; + clocks = <&clks 26>; + dmas = <&dma 12>, <&dma 13>, <&dma 14>, <&dma 15>; + dma-names = "rx0", "tx0", "rx1", "tx1"; + fsl,fifo-depth = <8>; + status = "disabled"; + }; + + ssi2: ssi@10011000 { + #sound-dai-cells = <0>; + compatible = "fsl,imx27-ssi", "fsl,imx21-ssi"; + reg = <0x10011000 0x1000>; + interrupts = <13>; + clocks = <&clks 25>; + dmas = <&dma 8>, <&dma 9>, <&dma 10>, <&dma 11>; + dma-names = "rx0", "tx0", "rx1", "tx1"; + fsl,fifo-depth = <8>; + status = "disabled"; + }; + i2c1: i2c@10012000 { #address-cells = <1>; #size-cells = <0>; @@ -236,64 +283,72 @@ status = "disabled"; }; - gpio1: gpio@10015000 { - compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; - reg = <0x10015000 0x100>; - interrupts = <8>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio2: gpio@10015100 { - compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; - reg = <0x10015100 0x100>; - interrupts = <8>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio3: gpio@10015200 { - compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; - reg = <0x10015200 0x100>; - interrupts = <8>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio4: gpio@10015300 { - compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; - reg = <0x10015300 0x100>; - interrupts = <8>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio5: gpio@10015400 { - compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; - reg = <0x10015400 0x100>; - interrupts = <8>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; - }; - - gpio6: gpio@10015500 { - compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; - reg = <0x10015500 0x100>; - interrupts = <8>; - gpio-controller; - #gpio-cells = <2>; - interrupt-controller; - #interrupt-cells = <2>; + iomuxc: iomuxc@10015000 { + compatible = "fsl,imx27-iomuxc"; + reg = <0x10015000 0x600>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio1: gpio@10015000 { + compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; + reg = <0x10015000 0x100>; + interrupts = <8>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio@10015100 { + compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; + reg = <0x10015100 0x100>; + interrupts = <8>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio@10015200 { + compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; + reg = <0x10015200 0x100>; + interrupts = <8>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio4: gpio@10015300 { + compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; + reg = <0x10015300 0x100>; + interrupts = <8>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio5: gpio@10015400 { + compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; + reg = <0x10015400 0x100>; + interrupts = <8>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio6: gpio@10015500 { + compatible = "fsl,imx27-gpio", "fsl,imx21-gpio"; + reg = <0x10015500 0x100>; + interrupts = <8>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; }; audmux: audmux@10016000 { @@ -404,6 +459,42 @@ iram = <&iram>; }; + usbotg: usb@10024000 { + compatible = "fsl,imx27-usb"; + reg = <0x10024000 0x200>; + interrupts = <56>; + clocks = <&clks 15>; + fsl,usbmisc = <&usbmisc 0>; + fsl,usbphy = <&usbphy0>; + status = "disabled"; + }; + + usbh1: usb@10024200 { + compatible = "fsl,imx27-usb"; + reg = <0x10024200 0x200>; + interrupts = <54>; + clocks = <&clks 15>; + fsl,usbmisc = <&usbmisc 1>; + status = "disabled"; + }; + + usbh2: usb@10024400 { + compatible = "fsl,imx27-usb"; + reg = <0x10024400 0x200>; + interrupts = <55>; + clocks = <&clks 15>; + fsl,usbmisc = <&usbmisc 2>; + fsl,usbphy = <&usbphy2>; + status = "disabled"; + }; + + usbmisc: usbmisc@10024600 { + #index-cells = <1>; + compatible = "fsl,imx27-usbmisc"; + reg = <0x10024600 0x200>; + clocks = <&clks 62>; + }; + sahara2: sahara@10025000 { compatible = "fsl,imx27-sahara"; reg = <0x10025000 0x1000>; diff --git a/arch/arm/boot/dts/imx28-apf28dev.dts b/arch/arm/boot/dts/imx28-apf28dev.dts index e2efd8d89c4f..221cac4fb2cd 100644 --- a/arch/arm/boot/dts/imx28-apf28dev.dts +++ b/arch/arm/boot/dts/imx28-apf28dev.dts @@ -48,6 +48,7 @@ MX28_PAD_LCD_D20__GPIO_1_20 MX28_PAD_LCD_D21__GPIO_1_21 MX28_PAD_LCD_D22__GPIO_1_22 + MX28_PAD_GPMI_CE1N__GPIO_0_17 >; fsl,drive-strength = <MXS_DRIVE_4mA>; fsl,voltage = <MXS_VOLTAGE_HIGH>; @@ -66,6 +67,16 @@ fsl,voltage = <MXS_VOLTAGE_HIGH>; fsl,pull-up = <MXS_PULL_DISABLE>; }; + + usb0_otg_apf28dev: otg-apf28dev@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_D23__GPIO_1_23 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; }; lcdif@80030000 { @@ -131,6 +142,8 @@ ahb@80080000 { usb0: usb@80080000 { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_otg_apf28dev>; vbus-supply = <®_usb0_vbus>; status = "okay"; }; @@ -150,13 +163,17 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_usb0_vbus: usb0_vbus { + reg_usb0_vbus: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "usb0_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; gpio = <&gpio1 23 1>; + enable-active-high; }; }; @@ -177,4 +194,14 @@ brightness-levels = <0 4 8 16 32 64 128 255>; default-brightness-level = <6>; }; + + gpio-keys { + compatible = "gpio-keys"; + + user-button { + label = "User button"; + gpios = <&gpio0 17 0>; + linux,code = <0x100>; + }; + }; }; diff --git a/arch/arm/boot/dts/imx28-apx4devkit.dts b/arch/arm/boot/dts/imx28-apx4devkit.dts index 6f254ca816cb..e1ce9179db63 100644 --- a/arch/arm/boot/dts/imx28-apx4devkit.dts +++ b/arch/arm/boot/dts/imx28-apx4devkit.dts @@ -193,9 +193,12 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_3p3v: 3p3v { + reg_3p3v: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "3P3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; diff --git a/arch/arm/boot/dts/imx28-cfa10036.dts b/arch/arm/boot/dts/imx28-cfa10036.dts index cabb6171a19d..ae7c3390e65a 100644 --- a/arch/arm/boot/dts/imx28-cfa10036.dts +++ b/arch/arm/boot/dts/imx28-cfa10036.dts @@ -100,6 +100,8 @@ usb0: usb@80080000 { pinctrl-names = "default"; pinctrl-0 = <&usb0_otg_cfa10036>; + dr_mode = "peripheral"; + phy_type = "utmi"; status = "okay"; }; }; diff --git a/arch/arm/boot/dts/imx28-cfa10037.dts b/arch/arm/boot/dts/imx28-cfa10037.dts index f93e9a700e52..e5beaa58bb40 100644 --- a/arch/arm/boot/dts/imx28-cfa10037.dts +++ b/arch/arm/boot/dts/imx28-cfa10037.dts @@ -54,7 +54,7 @@ ahb@80080000 { usb1: usb@80090000 { vbus-supply = <®_usb1_vbus>; - pinctrl-0 = <&usbphy1_pins_a>; + pinctrl-0 = <&usb1_pins_a>; pinctrl-names = "default"; status = "okay"; }; @@ -72,9 +72,12 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_usb1_vbus: usb1_vbus { + reg_usb1_vbus: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; pinctrl-names = "default"; pinctrl-0 = <&usb_pins_cfa10037>; regulator-name = "usb1_vbus"; diff --git a/arch/arm/boot/dts/imx28-cfa10049.dts b/arch/arm/boot/dts/imx28-cfa10049.dts index 7087b4bf6a8f..7d51459de5e8 100644 --- a/arch/arm/boot/dts/imx28-cfa10049.dts +++ b/arch/arm/boot/dts/imx28-cfa10049.dts @@ -229,15 +229,39 @@ i2c-parent = <&i2c1>; i2c@0 { + #address-cells = <1>; + #size-cells = <0>; reg = <0>; + + adc0: nau7802@2a { + compatible = "nuvoton,nau7802"; + reg = <0x2a>; + nuvoton,vldo = <3000>; + }; }; i2c@1 { + #address-cells = <1>; + #size-cells = <0>; reg = <1>; + + adc1: nau7802@2a { + compatible = "nuvoton,nau7802"; + reg = <0x2a>; + nuvoton,vldo = <3000>; + }; }; i2c@2 { + #address-cells = <1>; + #size-cells = <0>; reg = <2>; + + adc2: nau7802@2a { + compatible = "nuvoton,nau7802"; + reg = <0x2a>; + nuvoton,vldo = <3000>; + }; }; i2c@3 { @@ -274,7 +298,7 @@ ahb@80080000 { usb1: usb@80090000 { vbus-supply = <®_usb1_vbus>; - pinctrl-0 = <&usbphy1_pins_a>; + pinctrl-0 = <&usb1_pins_a>; pinctrl-names = "default"; status = "okay"; }; @@ -282,9 +306,12 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_usb1_vbus: usb1_vbus { + reg_usb1_vbus: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; pinctrl-names = "default"; pinctrl-0 = <&usb_pins_cfa10049>; regulator-name = "usb1_vbus"; diff --git a/arch/arm/boot/dts/imx28-cfa10057.dts b/arch/arm/boot/dts/imx28-cfa10057.dts index 3c1312885ae0..c4e00ce4b6da 100644 --- a/arch/arm/boot/dts/imx28-cfa10057.dts +++ b/arch/arm/boot/dts/imx28-cfa10057.dts @@ -134,7 +134,7 @@ ahb@80080000 { usb1: usb@80090000 { vbus-supply = <®_usb1_vbus>; - pinctrl-0 = <&usbphy1_pins_a>; + pinctrl-0 = <&usb1_pins_a>; pinctrl-names = "default"; status = "okay"; }; @@ -142,9 +142,12 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_usb1_vbus: usb1_vbus { + reg_usb1_vbus: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; pinctrl-names = "default"; pinctrl-0 = <&usb_pins_cfa10057>; regulator-name = "usb1_vbus"; diff --git a/arch/arm/boot/dts/imx28-cfa10058.dts b/arch/arm/boot/dts/imx28-cfa10058.dts index 2469d34df0ae..7c9cc783f0d1 100644 --- a/arch/arm/boot/dts/imx28-cfa10058.dts +++ b/arch/arm/boot/dts/imx28-cfa10058.dts @@ -101,7 +101,7 @@ ahb@80080000 { usb1: usb@80090000 { vbus-supply = <®_usb1_vbus>; - pinctrl-0 = <&usbphy1_pins_a>; + pinctrl-0 = <&usb1_pins_a>; pinctrl-names = "default"; status = "okay"; }; @@ -109,11 +109,14 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_usb1_vbus: usb1_vbus { + reg_usb1_vbus: regulator@0 { pinctrl-names = "default"; pinctrl-0 = <&usb_pins_cfa10058>; compatible = "regulator-fixed"; + reg = <0>; regulator-name = "usb1_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; diff --git a/arch/arm/boot/dts/imx28-duckbill.dts b/arch/arm/boot/dts/imx28-duckbill.dts new file mode 100644 index 000000000000..5f326c1c1850 --- /dev/null +++ b/arch/arm/boot/dts/imx28-duckbill.dts @@ -0,0 +1,121 @@ +/* + * Copyright (C) 2013 Michael Heimpold <mhei@heimpold.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx28.dtsi" + +/ { + model = "I2SE Duckbill"; + compatible = "i2se,duckbill", "fsl,imx28"; + + memory { + reg = <0x40000000 0x08000000>; + }; + + apb@80000000 { + apbh@80000000 { + ssp0: ssp@80010000 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_8bit_pins_a + &mmc0_cd_cfg &mmc0_sck_cfg>; + bus-width = <8>; + vmmc-supply = <®_3p3v>; + status = "okay"; + }; + + pinctrl@80018000 { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_a>; + + hog_pins_a: hog@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_ENET0_RX_CLK__GPIO_4_13 /* PHY Reset */ + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + led_pins_a: led_gpio@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART1_RX__GPIO_3_4 + MX28_PAD_AUART1_TX__GPIO_3_5 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + }; + }; + + apbx@80040000 { + duart: serial@80074000 { + pinctrl-names = "default"; + pinctrl-0 = <&duart_pins_a>; + status = "okay"; + }; + + usbphy0: usbphy@8007c000 { + status = "okay"; + }; + }; + }; + + ahb@80080000 { + usb0: usb@80080000 { + status = "okay"; + }; + + mac0: ethernet@800f0000 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac0_pins_a>; + phy-supply = <®_3p3v>; + phy-reset-gpios = <&gpio4 13 0>; + phy-reset-duration = <100>; + status = "okay"; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_3p3v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_a>; + + status { + label = "duckbill:green:status"; + gpios = <&gpio3 5 0>; + }; + + failure { + label = "duckbill:red:status"; + gpios = <&gpio3 4 0>; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx28-eukrea-mbmx283lc.dts b/arch/arm/boot/dts/imx28-eukrea-mbmx283lc.dts new file mode 100644 index 000000000000..7c1572c5a4fb --- /dev/null +++ b/arch/arm/boot/dts/imx28-eukrea-mbmx283lc.dts @@ -0,0 +1,71 @@ +/* + * Copyright 2013 Eukréa Electromatique <eric@eukrea.com> + * Copyright 2013 Eukréa Electromatique <denis@eukrea.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +/* + * Module contains : i.MX282 + 64MB DDR2 + NAND + Ethernet PHY + RTC + */ + +/dts-v1/; +#include "imx28-eukrea-mbmx28lc.dtsi" + +/ { + model = "Eukrea Electromatique MBMX283LC"; + compatible = "eukrea,mbmx283lc", "eukrea,mbmx28lc", "fsl,imx28"; + + memory { + reg = <0x40000000 0x04000000>; + }; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&gpmi_pins_a>; + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + pcf8563: rtc@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + + +&mac0 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac0_pins_a>; + phy-reset-gpios = <&gpio4 13 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&pinctrl{ + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_cpuimx283>; + + hog_pins_cpuimx283: hog-cpuimx283@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_ENET0_RX_CLK__GPIO_4_13 + MX28_PAD_ENET0_TX_CLK__GPIO_4_5 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; +}; diff --git a/arch/arm/boot/dts/imx28-eukrea-mbmx287lc.dts b/arch/arm/boot/dts/imx28-eukrea-mbmx287lc.dts new file mode 100644 index 000000000000..e773144e1e03 --- /dev/null +++ b/arch/arm/boot/dts/imx28-eukrea-mbmx287lc.dts @@ -0,0 +1,50 @@ +/* + * Copyright 2013 Eukréa Electromatique <eric@eukrea.com> + * Copyright 2013 Eukréa Electromatique <denis@eukrea.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +/* + * Module contains : i.MX287 + 128MB DDR2 + NAND + 2 x Ethernet PHY + RTC + */ + +#include "imx28-eukrea-mbmx283lc.dts" + +/ { + model = "Eukrea Electromatique MBMX287LC"; + compatible = "eukrea,mbmx287lc", "eukrea,mbmx283lc", "eukrea,mbmx28lc", "fsl,imx28"; + + memory { + reg = <0x40000000 0x08000000>; + }; +}; + +&mac1 { + phy-mode = "rmii"; + pinctrl-names = "default"; + pinctrl-0 = <&mac1_pins_a>; + phy-reset-gpios = <&gpio3 27 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&pinctrl { + pinctrl-names = "default"; + pinctrl-0 = <&hog_pins_cpuimx283 &hog_pins_cpuimx287>; + hog_pins_cpuimx287: hog-cpuimx287@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_SPDIF__GPIO_3_27 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; +}; diff --git a/arch/arm/boot/dts/imx28-eukrea-mbmx28lc.dtsi b/arch/arm/boot/dts/imx28-eukrea-mbmx28lc.dtsi new file mode 100644 index 000000000000..927b391d2058 --- /dev/null +++ b/arch/arm/boot/dts/imx28-eukrea-mbmx28lc.dtsi @@ -0,0 +1,326 @@ +/* + * Copyright 2013 Eukréa Electromatique <eric@eukrea.com> + * Copyright 2013 Eukréa Electromatique <denis@eukrea.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <dt-bindings/input/input.h> +#include <dt-bindings/gpio/gpio.h> +#include "imx28.dtsi" + +/ { + model = "Eukrea Electromatique MBMX28LC"; + compatible = "eukrea,mbmx28lc", "fsl,imx28"; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm 4 1000000>; + brightness-levels = <0 25 50 75 100 125 150 175 200 225 255>; + default-brightness-level = <10>; + }; + + button-sw3 { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_button_sw3_pins_mbmx28lc>; + + sw3 { + label = "SW3"; + gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; + linux,code = <BTN_MISC>; + gpio-key,wakeup; + }; + }; + + button-sw4 { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&gpio_button_sw4_pins_mbmx28lc>; + + sw4 { + label = "SW4"; + gpios = <&gpio1 20 GPIO_ACTIVE_LOW>; + linux,code = <BTN_MISC>; + gpio-key,wakeup; + }; + }; + + led-d6 { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_d6_pins_mbmx28lc>; + + led1 { + label = "d6"; + gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; + + led-d7 { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_d7_pins_mbmx28lc>; + + led1 { + label = "d7"; + gpios = <&gpio1 22 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-on"; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_3p3v: regulator@0 { + compatible = "regulator-fixed"; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_lcd_3v3: regulator@1 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <®_lcd_3v3_pins_mbmx28lc>; + regulator-name = "lcd-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb0_vbus: regulator@2 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <®_usb0_vbus_pins_mbmx28lc>; + regulator-name = "usb0_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 18 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb1_vbus: regulator@3 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <®_usb1_vbus_pins_mbmx28lc>; + regulator-name = "usb1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + }; + + sound { + compatible = "fsl,imx28-mbmx28lc-sgtl5000", + "fsl,mxs-audio-sgtl5000"; + model = "imx28-mbmx28lc-sgtl5000"; + saif-controllers = <&saif0 &saif1>; + audio-codec = <&sgtl5000>; + }; +}; + +&duart { + pinctrl-names = "default"; + pinctrl-0 = <&duart_4pins_a>; + status = "okay"; +}; + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + + sgtl5000: codec@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + VDDA-supply = <®_3p3v>; + VDDIO-supply = <®_3p3v>; + clocks = <&saif0>; + }; +}; + +&lcdif { + pinctrl-names = "default"; + pinctrl-0 = <&lcdif_18bit_pins_a &lcdif_pins_mbmx28lc>; + lcd-supply = <®_lcd_3v3>; + display = <&display0>; + status = "okay"; + + display0: display0 { + model = "43WVF1G-0"; + bits-per-pixel = <16>; + bus-width = <18>; + + display-timings { + native-mode = <&timing0>; + timing0: timing0 { + clock-frequency = <9072000>; + hactive = <480>; + vactive = <272>; + hback-porch = <10>; + hfront-porch = <5>; + vback-porch = <8>; + vfront-porch = <8>; + hsync-len = <40>; + vsync-len = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + }; + }; +}; + +&lradc { + fsl,lradc-touchscreen-wires = <4>; + status = "okay"; +}; + +&pinctrl { + gpio_button_sw3_pins_mbmx28lc: gpio-button-sw3-mbmx28lc@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_D21__GPIO_1_21 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + gpio_button_sw4_pins_mbmx28lc: gpio-button-sw4-mbmx28lc@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_D20__GPIO_1_20 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + lcdif_pins_mbmx28lc: lcdif-mbmx28lc@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_VSYNC__LCD_VSYNC + MX28_PAD_LCD_HSYNC__LCD_HSYNC + MX28_PAD_LCD_DOTCLK__LCD_DOTCLK + MX28_PAD_LCD_ENABLE__LCD_ENABLE + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + led_d6_pins_mbmx28lc: led-d6-mbmx28lc@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_D23__GPIO_1_23 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + led_d7_pins_mbmx28lc: led-d7-mbmx28lc@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_D22__GPIO_1_22 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + reg_lcd_3v3_pins_mbmx28lc: lcd-3v3-mbmx28lc@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_RESET__GPIO_3_30 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + reg_usb0_vbus_pins_mbmx28lc: reg-usb0-vbus-mbmx28lc@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_D18__GPIO_1_18 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + + reg_usb1_vbus_pins_mbmx28lc: reg-usb1-vbus-mbmx28lc@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_D19__GPIO_1_19 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm4_pins_a>; + status = "okay"; +}; + +&saif0 { + pinctrl-names = "default"; + pinctrl-0 = <&saif0_pins_a>; + status = "okay"; +}; + +&saif1 { + pinctrl-names = "default"; + pinctrl-0 = <&saif1_pins_a>; + fsl,saif-master = <&saif0>; + status = "okay"; +}; + +&ssp0 { + compatible = "fsl,imx28-mmc"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_4bit_pins_a &mmc0_cd_cfg &mmc0_sck_cfg>; + bus-width = <4>; + cd-inverted; + status = "okay"; +}; + +&usb0 { + disable-over-current; + vbus-supply = <®_usb0_vbus>; + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_pins_b>; +}; + +&usb1 { + vbus-supply = <®_usb1_vbus>; + status = "okay"; +}; + +&usbphy0 { + status = "okay"; +}; + +&usbphy1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts index 4267c2b05d60..e4cc44c98585 100644 --- a/arch/arm/boot/dts/imx28-evk.dts +++ b/arch/arm/boot/dts/imx28-evk.dts @@ -193,6 +193,7 @@ i2c0: i2c@80058000 { pinctrl-names = "default"; pinctrl-0 = <&i2c0_pins_a>; + clock-frequency = <400000>; status = "okay"; sgtl5000: codec@0a { @@ -278,33 +279,39 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_3p3v: 3p3v { + reg_3p3v: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "3P3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; }; - reg_vddio_sd0: vddio-sd0 { + reg_vddio_sd0: regulator@1 { compatible = "regulator-fixed"; + reg = <1>; regulator-name = "vddio-sd0"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; gpio = <&gpio3 28 0>; }; - reg_fec_3v3: fec-3v3 { + reg_fec_3v3: regulator@2 { compatible = "regulator-fixed"; + reg = <2>; regulator-name = "fec-3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; gpio = <&gpio2 15 0>; }; - reg_usb0_vbus: usb0_vbus { + reg_usb0_vbus: regulator@3 { compatible = "regulator-fixed"; + reg = <3>; regulator-name = "usb0_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; @@ -312,8 +319,9 @@ enable-active-high; }; - reg_usb1_vbus: usb1_vbus { + reg_usb1_vbus: regulator@4 { compatible = "regulator-fixed"; + reg = <4>; regulator-name = "usb1_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; @@ -321,8 +329,9 @@ enable-active-high; }; - reg_lcd_3v3: lcd-3v3 { + reg_lcd_3v3: regulator@5 { compatible = "regulator-fixed"; + reg = <5>; regulator-name = "lcd-3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; @@ -330,8 +339,9 @@ enable-active-high; }; - reg_can_3v3: can-3v3 { + reg_can_3v3: regulator@6 { compatible = "regulator-fixed"; + reg = <6>; regulator-name = "can-3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; diff --git a/arch/arm/boot/dts/imx28-m28cu3.dts b/arch/arm/boot/dts/imx28-m28cu3.dts index d3958da60bd7..9348ce59dda4 100644 --- a/arch/arm/boot/dts/imx28-m28cu3.dts +++ b/arch/arm/boot/dts/imx28-m28cu3.dts @@ -116,7 +116,6 @@ pinctrl-0 = <&lcdif_24bit_pins_a &lcdif_pins_m28>; display = <&display>; - reset-active-high; status = "okay"; display: display0 { @@ -180,7 +179,7 @@ usb1: usb@80090000 { vbus-supply = <®_usb1_vbus>; pinctrl-names = "default"; - pinctrl-0 = <&usbphy1_pins_a>; + pinctrl-0 = <&usb1_pins_a>; disable-over-current; status = "okay"; }; @@ -229,33 +228,39 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_3p3v: 3p3v { + reg_3p3v: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "3P3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; }; - reg_vddio_sd0: vddio-sd0 { + reg_vddio_sd0: regulator@1 { compatible = "regulator-fixed"; + reg = <1>; regulator-name = "vddio-sd0"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; gpio = <&gpio3 29 0>; }; - reg_vddio_sd1: vddio-sd1 { + reg_vddio_sd1: regulator@2 { compatible = "regulator-fixed"; + reg = <2>; regulator-name = "vddio-sd1"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; gpio = <&gpio2 19 0>; }; - reg_usb1_vbus: usb1_vbus { + reg_usb1_vbus: regulator@3 { compatible = "regulator-fixed"; + reg = <3>; regulator-name = "usb1_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; diff --git a/arch/arm/boot/dts/imx28-m28evk.dts b/arch/arm/boot/dts/imx28-m28evk.dts index 8e2477fbe1d7..f0ad7b9b9d9a 100644 --- a/arch/arm/boot/dts/imx28-m28evk.dts +++ b/arch/arm/boot/dts/imx28-m28evk.dts @@ -194,7 +194,7 @@ }; rtc: rtc@68 { - compatible = "stm,mt41t62"; + compatible = "stm,m41t62"; reg = <0x68>; }; }; @@ -248,14 +248,14 @@ usb0: usb@80080000 { vbus-supply = <®_usb0_vbus>; pinctrl-names = "default"; - pinctrl-0 = <&usbphy0_pins_a>; + pinctrl-0 = <&usb0_pins_a>; status = "okay"; }; usb1: usb@80090000 { vbus-supply = <®_usb1_vbus>; pinctrl-names = "default"; - pinctrl-0 = <&usbphy1_pins_a>; + pinctrl-0 = <&usb1_pins_a>; status = "okay"; }; @@ -285,33 +285,39 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_3p3v: 3p3v { + reg_3p3v: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "3P3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; }; - reg_vddio_sd0: vddio-sd0 { + reg_vddio_sd0: regulator@1 { compatible = "regulator-fixed"; + reg = <1>; regulator-name = "vddio-sd0"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; gpio = <&gpio3 28 0>; }; - reg_usb0_vbus: usb0_vbus { + reg_usb0_vbus: regulator@2 { compatible = "regulator-fixed"; + reg = <2>; regulator-name = "usb0_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; gpio = <&gpio3 12 0>; }; - reg_usb1_vbus: usb1_vbus { + reg_usb1_vbus: regulator@3 { compatible = "regulator-fixed"; + reg = <3>; regulator-name = "usb1_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; diff --git a/arch/arm/boot/dts/imx28-sps1.dts b/arch/arm/boot/dts/imx28-sps1.dts index 4870f07bf56a..0ce3cb8e7914 100644 --- a/arch/arm/boot/dts/imx28-sps1.dts +++ b/arch/arm/boot/dts/imx28-sps1.dts @@ -106,7 +106,7 @@ usb0: usb@80080000 { vbus-supply = <®_usb0_vbus>; pinctrl-names = "default"; - pinctrl-0 = <&usbphy0_pins_b>; + pinctrl-0 = <&usb0_pins_b>; status = "okay"; }; @@ -127,9 +127,12 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_usb0_vbus: usb0_vbus { + reg_usb0_vbus: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "usb0_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; diff --git a/arch/arm/boot/dts/imx28-tx28.dts b/arch/arm/boot/dts/imx28-tx28.dts index be5a0550d58c..e14bd86f3e99 100644 --- a/arch/arm/boot/dts/imx28-tx28.dts +++ b/arch/arm/boot/dts/imx28-tx28.dts @@ -43,9 +43,12 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_usb0_vbus: usb0_vbus { + reg_usb0_vbus: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "usb0_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; @@ -53,8 +56,9 @@ enable-active-high; }; - reg_usb1_vbus: usb1_vbus { + reg_usb1_vbus: regulator@1 { compatible = "regulator-fixed"; + reg = <1>; regulator-name = "usb1_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; @@ -62,35 +66,38 @@ enable-active-high; }; - reg_2p5v: 2p5v { + reg_2p5v: regulator@2 { compatible = "regulator-fixed"; + reg = <2>; regulator-name = "2P5V"; regulator-min-microvolt = <2500000>; regulator-max-microvolt = <2500000>; regulator-always-on; }; - reg_3p3v: 3p3v { + reg_3p3v: regulator@3 { compatible = "regulator-fixed"; + reg = <3>; regulator-name = "3P3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; }; - reg_can_xcvr: can-xcvr { + reg_can_xcvr: regulator@4 { compatible = "regulator-fixed"; + reg = <4>; regulator-name = "CAN XCVR"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; gpio = <&gpio1 0 0>; - enable-active-low; pinctrl-names = "default"; pinctrl-0 = <&tx28_flexcan_xcvr_pins>; }; - reg_lcd: lcd-power { + reg_lcd: regulator@5 { compatible = "regulator-fixed"; + reg = <5>; regulator-name = "LCD POWER"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; @@ -98,8 +105,9 @@ enable-active-high; }; - reg_lcd_reset: lcd-reset { + reg_lcd_reset: regulator@6 { compatible = "regulator-fixed"; + reg = <6>; regulator-name = "LCD RESET"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index f8e9b20f6982..90a579532b8b 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -32,6 +32,8 @@ serial4 = &auart4; spi0 = &ssp1; spi1 = &ssp2; + usbphy0 = &usbphy0; + usbphy1 = &usbphy1; }; cpus { @@ -343,6 +345,19 @@ fsl,pull-up = <MXS_PULL_DISABLE>; }; + auart2_pins_a: auart2-pins@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_AUART2_RX__AUART2_RX + MX28_PAD_AUART2_TX__AUART2_TX + MX28_PAD_AUART2_CTS__AUART2_CTS + MX28_PAD_AUART2_RTS__AUART2_RTS + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + auart3_pins_a: auart3@0 { reg = <0>; fsl,pinmux-ids = < @@ -655,6 +670,33 @@ fsl,pull-up = <MXS_PULL_DISABLE>; }; + lcdif_18bit_pins_a: lcdif-18bit@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_LCD_D00__LCD_D0 + MX28_PAD_LCD_D01__LCD_D1 + MX28_PAD_LCD_D02__LCD_D2 + MX28_PAD_LCD_D03__LCD_D3 + MX28_PAD_LCD_D04__LCD_D4 + MX28_PAD_LCD_D05__LCD_D5 + MX28_PAD_LCD_D06__LCD_D6 + MX28_PAD_LCD_D07__LCD_D7 + MX28_PAD_LCD_D08__LCD_D8 + MX28_PAD_LCD_D09__LCD_D9 + MX28_PAD_LCD_D10__LCD_D10 + MX28_PAD_LCD_D11__LCD_D11 + MX28_PAD_LCD_D12__LCD_D12 + MX28_PAD_LCD_D13__LCD_D13 + MX28_PAD_LCD_D14__LCD_D14 + MX28_PAD_LCD_D15__LCD_D15 + MX28_PAD_LCD_D16__LCD_D16 + MX28_PAD_LCD_D17__LCD_D17 + >; + fsl,drive-strength = <MXS_DRIVE_4mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_DISABLE>; + }; + lcdif_16bit_pins_a: lcdif-16bit@0 { reg = <0>; fsl,pinmux-ids = < @@ -743,7 +785,7 @@ fsl,pull-up = <MXS_PULL_DISABLE>; }; - usbphy0_pins_a: usbphy0@0 { + usb0_pins_a: usb0@0 { reg = <0>; fsl,pinmux-ids = < MX28_PAD_SSP2_SS2__USB0_OVERCURRENT @@ -753,7 +795,7 @@ fsl,pull-up = <MXS_PULL_DISABLE>; }; - usbphy0_pins_b: usbphy0@1 { + usb0_pins_b: usb0@1 { reg = <1>; fsl,pinmux-ids = < MX28_PAD_AUART1_CTS__USB0_OVERCURRENT @@ -763,7 +805,7 @@ fsl,pull-up = <MXS_PULL_DISABLE>; }; - usbphy1_pins_a: usbphy1@0 { + usb1_pins_a: usb1@0 { reg = <0>; fsl,pinmux-ids = < MX28_PAD_SSP2_SS1__USB1_OVERCURRENT @@ -782,6 +824,17 @@ fsl,voltage = <MXS_VOLTAGE_HIGH>; fsl,pull-up = <MXS_PULL_ENABLE>; }; + + usb0_id_pins_b: usb0id1@0 { + reg = <0>; + fsl,pinmux-ids = < + MX28_PAD_PWM2__USB0_ID + >; + fsl,drive-strength = <MXS_DRIVE_12mA>; + fsl,voltage = <MXS_VOLTAGE_HIGH>; + fsl,pull-up = <MXS_PULL_ENABLE>; + }; + }; digctl: digctl@8001c000 { @@ -946,6 +999,7 @@ 20 21 22 23 24 25>; status = "disabled"; clocks = <&clks 41>; + #io-channel-cells = <1>; }; spdif: spdif@80054000 { @@ -1130,4 +1184,9 @@ status = "disabled"; }; }; + + iio_hwmon { + compatible = "iio-hwmon"; + io-channels = <&lradc 8>; + }; }; diff --git a/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi b/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi new file mode 100644 index 000000000000..906ae937b013 --- /dev/null +++ b/arch/arm/boot/dts/imx35-eukrea-cpuimx35.dtsi @@ -0,0 +1,81 @@ +/* + * Copyright 2013 Eukréa Electromatique <denis@eukrea.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include "imx35.dtsi" + +/ { + model = "Eukrea CPUIMX35"; + compatible = "eukrea,cpuimx35", "fsl,imx35"; + + memory { + reg = <0x80000000 0x8000000>; /* 128M */ + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pcf8563@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +&iomuxc { + imx35-eukrea { + pinctrl_fec: fecgrp { + fsl,pins = < + MX35_PAD_FEC_TX_CLK__FEC_TX_CLK 0x80000000 + MX35_PAD_FEC_RX_CLK__FEC_RX_CLK 0x80000000 + MX35_PAD_FEC_RX_DV__FEC_RX_DV 0x80000000 + MX35_PAD_FEC_COL__FEC_COL 0x80000000 + MX35_PAD_FEC_RDATA0__FEC_RDATA_0 0x80000000 + MX35_PAD_FEC_TDATA0__FEC_TDATA_0 0x80000000 + MX35_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000 + MX35_PAD_FEC_MDC__FEC_MDC 0x80000000 + MX35_PAD_FEC_MDIO__FEC_MDIO 0x80000000 + MX35_PAD_FEC_TX_ERR__FEC_TX_ERR 0x80000000 + MX35_PAD_FEC_RX_ERR__FEC_RX_ERR 0x80000000 + MX35_PAD_FEC_CRS__FEC_CRS 0x80000000 + MX35_PAD_FEC_RDATA1__FEC_RDATA_1 0x80000000 + MX35_PAD_FEC_TDATA1__FEC_TDATA_1 0x80000000 + MX35_PAD_FEC_RDATA2__FEC_RDATA_2 0x80000000 + MX35_PAD_FEC_TDATA2__FEC_TDATA_2 0x80000000 + MX35_PAD_FEC_RDATA3__FEC_RDATA_3 0x80000000 + MX35_PAD_FEC_TDATA3__FEC_TDATA_3 0x80000000 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX35_PAD_I2C1_CLK__I2C1_SCL 0x80000000 + MX35_PAD_I2C1_DAT__I2C1_SDA 0x80000000 + >; + }; + }; +}; + +&nfc { + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard.dts b/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard.dts new file mode 100644 index 000000000000..1bdec21f4533 --- /dev/null +++ b/arch/arm/boot/dts/imx35-eukrea-mbimxsd35-baseboard.dts @@ -0,0 +1,143 @@ +/* + * Copyright 2013 Eukréa Electromatique <denis@eukrea.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include "imx35-eukrea-cpuimx35.dtsi" + +/ { + model = "Eukrea CPUIMX35"; + compatible = "eukrea,mbimxsd35-baseboard", "eukrea,cpuimx35", "fsl,imx35"; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_bp1>; + + bp1 { + label = "BP1"; + gpios = <&gpio3 25 GPIO_ACTIVE_LOW>; + linux,code = <BTN_MISC>; + gpio-key,wakeup; + linux,input-type = <1>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led1>; + + led1 { + label = "led1"; + gpios = <&gpio3 29 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&esdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc1>; + cd-gpios = <&gpio3 24>; + status = "okay"; +}; + +&i2c1 { + tlv320aic23: codec@1a { + compatible = "ti,tlv320aic23"; + reg = <0x1a>; + }; +}; + +&iomuxc { + imx35-eukrea { + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX35_PAD_STXFS4__AUDMUX_AUD4_TXFS 0x80000000 + MX35_PAD_STXD4__AUDMUX_AUD4_TXD 0x80000000 + MX35_PAD_SRXD4__AUDMUX_AUD4_RXD 0x80000000 + MX35_PAD_SCK4__AUDMUX_AUD4_TXC 0x80000000 + >; + }; + + pinctrl_bp1: bp1grp { + fsl,pins = <MX35_PAD_LD19__GPIO3_25 0x80000000>; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + MX35_PAD_SD1_CMD__ESDHC1_CMD 0x80000000 + MX35_PAD_SD1_CLK__ESDHC1_CLK 0x80000000 + MX35_PAD_SD1_DATA0__ESDHC1_DAT0 0x80000000 + MX35_PAD_SD1_DATA1__ESDHC1_DAT1 0x80000000 + MX35_PAD_SD1_DATA2__ESDHC1_DAT2 0x80000000 + MX35_PAD_SD1_DATA3__ESDHC1_DAT3 0x80000000 + MX35_PAD_LD18__GPIO3_24 0x80000000 /* CD */ + >; + }; + + pinctrl_led1: led1grp { + fsl,pins = <MX35_PAD_LD23__GPIO3_29 0x80000000>; + }; + + pinctrl_reg_lcd_3v3: reg-lcd-3v3 { + fsl,pins = <MX35_PAD_D3_CLS__GPIO1_4 0x80000000>; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX35_PAD_TXD1__UART1_TXD_MUX 0x1c5 + MX35_PAD_RXD1__UART1_RXD_MUX 0x1c5 + MX35_PAD_CTS1__UART1_CTS 0x1c5 + MX35_PAD_RTS1__UART1_RTS 0x1c5 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX35_PAD_RXD2__UART2_RXD_MUX 0x1c5 + MX35_PAD_TXD2__UART2_TXD_MUX 0x1c5 + MX35_PAD_RTS2__UART2_RTS 0x1c5 + MX35_PAD_CTS2__UART2_CTS 0x1c5 + >; + }; + }; +}; + +&ssi1 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + fsl,uart-has-rtscts; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx35.dtsi b/arch/arm/boot/dts/imx35.dtsi new file mode 100644 index 000000000000..88b218f8f810 --- /dev/null +++ b/arch/arm/boot/dts/imx35.dtsi @@ -0,0 +1,359 @@ +/* + * Copyright 2012 Steffen Trumtrar, Pengutronix + * + * based on imx27.dtsi + * + * This program is free software; you can redistribute it and/or modify it under + * the terms of the GNU General Public License version 2 as published by the + * Free Software Foundation. + */ + +#include "skeleton.dtsi" +#include "imx35-pinfunc.h" + +/ { + aliases { + gpio0 = &gpio1; + gpio1 = &gpio2; + gpio2 = &gpio3; + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + spi0 = &spi1; + spi1 = &spi2; + }; + + cpus { + #address-cells = <0>; + #size-cells = <0>; + + cpu { + compatible = "arm,arm1136"; + device_type = "cpu"; + }; + }; + + avic: avic-interrupt-controller@68000000 { + compatible = "fsl,imx35-avic", "fsl,avic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x68000000 0x10000000>; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + interrupt-parent = <&avic>; + ranges; + + L2: l2-cache@30000000 { + compatible = "arm,l210-cache"; + reg = <0x30000000 0x1000>; + cache-unified; + cache-level = <2>; + }; + + aips1: aips@43f00000 { + compatible = "fsl,aips", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x43f00000 0x100000>; + ranges; + + i2c1: i2c@43f80000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx35-i2c", "fsl,imx1-i2c"; + reg = <0x43f80000 0x4000>; + clocks = <&clks 51>; + clock-names = "ipg_per"; + interrupts = <10>; + status = "disabled"; + }; + + i2c3: i2c@43f84000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx35-i2c", "fsl,imx1-i2c"; + reg = <0x43f84000 0x4000>; + clocks = <&clks 53>; + clock-names = "ipg_per"; + interrupts = <3>; + status = "disabled"; + }; + + uart1: serial@43f90000 { + compatible = "fsl,imx35-uart", "fsl,imx21-uart"; + reg = <0x43f90000 0x4000>; + clocks = <&clks 9>, <&clks 70>; + clock-names = "ipg", "per"; + interrupts = <45>; + status = "disabled"; + }; + + uart2: serial@43f94000 { + compatible = "fsl,imx35-uart", "fsl,imx21-uart"; + reg = <0x43f94000 0x4000>; + clocks = <&clks 9>, <&clks 71>; + clock-names = "ipg", "per"; + interrupts = <32>; + status = "disabled"; + }; + + i2c2: i2c@43f98000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx35-i2c", "fsl,imx1-i2c"; + reg = <0x43f98000 0x4000>; + clocks = <&clks 52>; + clock-names = "ipg_per"; + interrupts = <4>; + status = "disabled"; + }; + + ssi1: ssi@43fa0000 { + compatible = "fsl,imx35-ssi", "fsl,imx21-ssi"; + reg = <0x43fa0000 0x4000>; + interrupts = <11>; + clocks = <&clks 68>; + dmas = <&sdma 28 0 0>, + <&sdma 29 0 0>; + dma-names = "rx", "tx"; + fsl,fifo-depth = <15>; + status = "disabled"; + }; + + spi1: cspi@43fa4000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx35-cspi"; + reg = <0x43fa4000 0x4000>; + clocks = <&clks 35 &clks 35>; + clock-names = "ipg", "per"; + interrupts = <14>; + status = "disabled"; + }; + + iomuxc: iomuxc@43fac000 { + compatible = "fsl,imx35-iomuxc"; + reg = <0x43fac000 0x4000>; + }; + }; + + spba: spba-bus@50000000 { + compatible = "fsl,spba-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x50000000 0x100000>; + ranges; + + uart3: serial@5000c000 { + compatible = "fsl,imx35-uart", "fsl,imx21-uart"; + reg = <0x5000c000 0x4000>; + clocks = <&clks 9>, <&clks 72>; + clock-names = "ipg", "per"; + interrupts = <18>; + status = "disabled"; + }; + + spi2: cspi@50010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx35-cspi"; + reg = <0x50010000 0x4000>; + interrupts = <13>; + clocks = <&clks 36 &clks 36>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + fec: fec@50038000 { + compatible = "fsl,imx35-fec", "fsl,imx27-fec"; + reg = <0x50038000 0x4000>; + clocks = <&clks 46>, <&clks 8>; + clock-names = "ipg", "ahb"; + interrupts = <57>; + status = "disabled"; + }; + }; + + aips2: aips@53f00000 { + compatible = "fsl,aips", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x53f00000 0x100000>; + ranges; + + clks: ccm@53f80000 { + compatible = "fsl,imx35-ccm"; + reg = <0x53f80000 0x4000>; + interrupts = <31>; + #clock-cells = <1>; + }; + + gpio3: gpio@53fa4000 { + compatible = "fsl,imx35-gpio", "fsl,imx31-gpio"; + reg = <0x53fa4000 0x4000>; + interrupts = <56>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + esdhc1: esdhc@53fb4000 { + compatible = "fsl,imx35-esdhc"; + reg = <0x53fb4000 0x4000>; + interrupts = <7>; + clocks = <&clks 9>, <&clks 8>, <&clks 43>; + clock-names = "ipg", "ahb", "per"; + status = "disabled"; + }; + + esdhc2: esdhc@53fb8000 { + compatible = "fsl,imx35-esdhc"; + reg = <0x53fb8000 0x4000>; + interrupts = <8>; + clocks = <&clks 9>, <&clks 8>, <&clks 44>; + clock-names = "ipg", "ahb", "per"; + status = "disabled"; + }; + + esdhc3: esdhc@53fbc000 { + compatible = "fsl,imx35-esdhc"; + reg = <0x53fbc000 0x4000>; + interrupts = <9>; + clocks = <&clks 9>, <&clks 8>, <&clks 45>; + clock-names = "ipg", "ahb", "per"; + status = "disabled"; + }; + + audmux: audmux@53fc4000 { + compatible = "fsl,imx35-audmux", "fsl,imx31-audmux"; + reg = <0x53fc4000 0x4000>; + status = "disabled"; + }; + + gpio1: gpio@53fcc000 { + compatible = "fsl,imx35-gpio", "fsl,imx31-gpio"; + reg = <0x53fcc000 0x4000>; + interrupts = <52>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio@53fd0000 { + compatible = "fsl,imx35-gpio", "fsl,imx31-gpio"; + reg = <0x53fd0000 0x4000>; + interrupts = <51>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + sdma: sdma@53fd4000 { + compatible = "fsl,imx35-sdma"; + reg = <0x53fd4000 0x4000>; + clocks = <&clks 9>, <&clks 65>; + clock-names = "ipg", "ahb"; + #dma-cells = <3>; + interrupts = <34>; + fsl,sdma-ram-script-name = "imx/sdma/sdma-imx35.bin"; + }; + + wdog: wdog@53fdc000 { + compatible = "fsl,imx35-wdt", "fsl,imx21-wdt"; + reg = <0x53fdc000 0x4000>; + clocks = <&clks 74>; + clock-names = ""; + interrupts = <55>; + }; + + can1: can@53fe4000 { + compatible = "fsl,imx35-flexcan", "fsl,p1010-flexcan"; + reg = <0x53fe4000 0x1000>; + clocks = <&clks 33>; + clock-names = "ipg"; + interrupts = <43>; + status = "disabled"; + }; + + can2: can@53fe8000 { + compatible = "fsl,imx35-flexcan", "fsl,p1010-flexcan"; + reg = <0x53fe8000 0x1000>; + clocks = <&clks 34>; + clock-names = "ipg"; + interrupts = <44>; + status = "disabled"; + }; + + usbotg: usb@53ff4000 { + compatible = "fsl,imx35-usb", "fsl,imx27-usb"; + reg = <0x53ff4000 0x0200>; + interrupts = <37>; + clocks = <&clks 9>, <&clks 73>, <&clks 28>; + clock-names = "ipg", "ahb", "per"; + fsl,usbmisc = <&usbmisc 0>; + status = "disabled"; + }; + + usbhost1: usb@53ff4400 { + compatible = "fsl,imx35-usb", "fsl,imx27-usb"; + reg = <0x53ff4400 0x0200>; + interrupts = <35>; + clocks = <&clks 9>, <&clks 73>, <&clks 28>; + clock-names = "ipg", "ahb", "per"; + fsl,usbmisc = <&usbmisc 1>; + status = "disabled"; + }; + + usbmisc: usbmisc@53ff4600 { + #index-cells = <1>; + compatible = "fsl,imx35-usbmisc"; + clocks = <&clks 9>, <&clks 73>, <&clks 28>; + clock-names = "ipg", "ahb", "per"; + reg = <0x53ff4600 0x00f>; + }; + }; + + emi@80000000 { /* External Memory Interface */ + compatible = "fsl,emi", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x80000000 0x40000000>; + ranges; + + nfc: nand@bb000000 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,imx35-nand", "fsl,imx25-nand"; + reg = <0xbb000000 0x2000>; + clocks = <&clks 29>; + clock-names = ""; + interrupts = <33>; + status = "disabled"; + }; + + weim: weim@b8002000 { + #address-cells = <2>; + #size-cells = <1>; + clocks = <&clks 0>; + compatible = "fsl,imx35-weim", "fsl,imx27-weim"; + reg = <0xb8002000 0x1000>; + ranges = < + 0 0 0xa0000000 0x8000000 + 1 0 0xa8000000 0x8000000 + 2 0 0xb0000000 0x2000000 + 3 0 0xb2000000 0x2000000 + 4 0 0xb4000000 0x2000000 + 5 0 0xb6000000 0x2000000 + >; + status = "disabled"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx50-evk.dts b/arch/arm/boot/dts/imx50-evk.dts new file mode 100644 index 000000000000..1b22512c91bd --- /dev/null +++ b/arch/arm/boot/dts/imx50-evk.dts @@ -0,0 +1,119 @@ +/* + * Copyright 2013 Greg Ungerer <gerg@uclinux.org> + * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx50.dtsi" + +/ { + model = "Freescale i.MX50 Evaluation Kit"; + compatible = "fsl,imx50-evk", "fsl,imx50"; + + memory { + reg = <0x70000000 0x80000000>; + }; +}; + +&cspi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_cspi>; + fsl,spi-num-chipselects = <2>; + cs-gpios = <&gpio4 11 0>, <&gpio4 13 0>; + status = "okay"; + + flash: m25p32@1 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p32", "m25p80"; + spi-max-frequency = <25000000>; + reg = <1>; + + partition@0 { + label = "bootloader"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "kernel"; + reg = <0x100000 0x300000>; + }; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + phy-mode = "rmii"; + phy-reset-gpios = <&gpio4 12 0>; + status = "okay"; +}; + +&iomuxc { + imx50-evk { + pinctrl_cspi: cspigrp { + fsl,pins = < + MX50_PAD_CSPI_SCLK__CSPI_SCLK 0x00 + MX50_PAD_CSPI_MISO__CSPI_MISO 0x00 + MX50_PAD_CSPI_MOSI__CSPI_MOSI 0x00 + MX50_PAD_CSPI_SS0__GPIO4_11 0xc4 + MX50_PAD_ECSPI1_MOSI__CSPI_SS1 0xf4 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX50_PAD_SSI_RXFS__FEC_MDC 0x80 + MX50_PAD_SSI_RXC__FEC_MDIO 0x80 + MX50_PAD_DISP_D0__FEC_TX_CLK 0x80 + MX50_PAD_DISP_D1__FEC_RX_ERR 0x80 + MX50_PAD_DISP_D2__FEC_RX_DV 0x80 + MX50_PAD_DISP_D3__FEC_RDATA_1 0x80 + MX50_PAD_DISP_D4__FEC_RDATA_0 0x80 + MX50_PAD_DISP_D5__FEC_TX_EN 0x80 + MX50_PAD_DISP_D6__FEC_TDATA_1 0x80 + MX50_PAD_DISP_D7__FEC_TDATA_0 0x80 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX50_PAD_UART1_TXD__UART1_TXD_MUX 0x1e4 + MX50_PAD_UART1_RXD__UART1_RXD_MUX 0x1e4 + MX50_PAD_UART1_RTS__UART1_RTS 0x1e4 + MX50_PAD_UART1_CTS__UART1_CTS 0x1e4 + >; + }; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&usbh1 { + status = "okay"; +}; + +&usbh2 { + status = "okay"; +}; + +&usbh3 { + status = "okay"; +}; + +&usbotg { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx50-pinfunc.h b/arch/arm/boot/dts/imx50-pinfunc.h new file mode 100644 index 000000000000..97e6e7f4ebdd --- /dev/null +++ b/arch/arm/boot/dts/imx50-pinfunc.h @@ -0,0 +1,923 @@ +/* + * Copyright 2013 Greg Ungerer <gerg@uclinux.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + */ + +#ifndef __DTS_IMX50_PINFUNC_H +#define __DTS_IMX50_PINFUNC_H + +/* + * The pin function ID is a tuple of + * <mux_reg conf_reg input_reg mux_mode input_val> + */ +#define MX50_PAD_KEY_COL0__KPP_COL_0 0x020 0x2cc 0x000 0x0 0x0 +#define MX50_PAD_KEY_COL0__GPIO4_0 0x020 0x2cc 0x000 0x1 0x0 +#define MX50_PAD_KEY_COL0__EIM_NANDF_CLE 0x020 0x2cc 0x000 0x2 0x0 +#define MX50_PAD_KEY_COL0__CTI_TRIGIN7 0x020 0x2cc 0x000 0x6 0x0 +#define MX50_PAD_KEY_COL0__USBPHY1_TXREADY 0x020 0x2cc 0x000 0x7 0x0 +#define MX50_PAD_KEY_ROW0__KPP_ROW_0 0x024 0x2d0 0x000 0x0 0x0 +#define MX50_PAD_KEY_ROW0__GPIO4_1 0x024 0x2d0 0x000 0x1 0x0 +#define MX50_PAD_KEY_ROW0__EIM_NANDF_ALE 0x024 0x2d0 0x000 0x2 0x0 +#define MX50_PAD_KEY_ROW0__CTI_TRIGIN_ACK7 0x024 0x2d0 0x000 0x6 0x0 +#define MX50_PAD_KEY_ROW0__USBPHY1_RXVALID 0x024 0x2d0 0x000 0x7 0x0 +#define MX50_PAD_KEY_COL1__KPP_COL_1 0x028 0x2d4 0x000 0x0 0x0 +#define MX50_PAD_KEY_COL1__GPIO4_2 0x028 0x2d4 0x000 0x1 0x0 +#define MX50_PAD_KEY_COL1__EIM_NANDF_CEN_0 0x028 0x2d4 0x000 0x2 0x0 +#define MX50_PAD_KEY_COL1__CTI_TRIGOUT_ACK6 0x028 0x2d4 0x000 0x6 0x0 +#define MX50_PAD_KEY_COL1__USBPHY1_RXACTIVE 0x028 0x2d4 0x000 0x7 0x0 +#define MX50_PAD_KEY_ROW1__KPP_ROW_1 0x02c 0x2d8 0x000 0x0 0x0 +#define MX50_PAD_KEY_ROW1__GPIO4_3 0x02c 0x2d8 0x000 0x1 0x0 +#define MX50_PAD_KEY_ROW1__EIM_NANDF_CEN_1 0x02c 0x2d8 0x000 0x2 0x0 +#define MX50_PAD_KEY_ROW1__CTI_TRIGOUT_ACK7 0x02c 0x2d8 0x000 0x6 0x0 +#define MX50_PAD_KEY_ROW1__USBPHY1_RXERROR 0x02c 0x2d8 0x000 0x7 0x0 +#define MX50_PAD_KEY_COL2__KPP_COL_1 0x030 0x2dc 0x000 0x0 0x0 +#define MX50_PAD_KEY_COL2__GPIO4_4 0x030 0x2dc 0x000 0x1 0x0 +#define MX50_PAD_KEY_COL2__EIM_NANDF_CEN_2 0x030 0x2dc 0x000 0x2 0x0 +#define MX50_PAD_KEY_COL2__CTI_TRIGOUT6 0x030 0x2dc 0x000 0x6 0x0 +#define MX50_PAD_KEY_COL2__USBPHY1_SIECLOCK 0x030 0x2dc 0x000 0x7 0x0 +#define MX50_PAD_KEY_ROW2__KPP_ROW_2 0x034 0x2e0 0x000 0x0 0x0 +#define MX50_PAD_KEY_ROW2__GPIO4_5 0x034 0x2e0 0x000 0x1 0x0 +#define MX50_PAD_KEY_ROW2__EIM_NANDF_CEN_3 0x034 0x2e0 0x000 0x2 0x0 +#define MX50_PAD_KEY_ROW2__CTI_TRIGOUT7 0x034 0x2e0 0x000 0x6 0x0 +#define MX50_PAD_KEY_ROW2__USBPHY1_LINESTATE_0 0x034 0x2e0 0x000 0x7 0x0 +#define MX50_PAD_KEY_COL3__KPP_COL_2 0x038 0x2e4 0x000 0x0 0x0 +#define MX50_PAD_KEY_COL3__GPIO4_6 0x038 0x2e4 0x000 0x1 0x0 +#define MX50_PAD_KEY_COL3__EIM_NANDF_READY0 0x038 0x2e4 0x7b4 0x2 0x0 +#define MX50_PAD_KEY_COL3__SDMA_EXT_EVENT_0 0x038 0x2e4 0x7b8 0x6 0x0 +#define MX50_PAD_KEY_COL3__USBPHY1_LINESTATE_1 0x038 0x2e4 0x000 0x7 0x0 +#define MX50_PAD_KEY_ROW3__KPP_ROW_3 0x03c 0x2e8 0x000 0x0 0x0 +#define MX50_PAD_KEY_ROW3__GPIO4_7 0x03c 0x2e8 0x000 0x1 0x0 +#define MX50_PAD_KEY_ROW3__EIM_NANDF_DQS 0x03c 0x2e8 0x7b0 0x2 0x0 +#define MX50_PAD_KEY_ROW3__SDMA_EXT_EVENT_1 0x03c 0x2e8 0x7bc 0x6 0x0 +#define MX50_PAD_KEY_ROW3__USBPHY1_VBUSVALID 0x03c 0x2e8 0x000 0x7 0x0 +#define MX50_PAD_I2C1_SCL__I2C1_SCL 0x040 0x2ec 0x000 0x0 0x0 +#define MX50_PAD_I2C1_SCL__GPIO6_18 0x040 0x2ec 0x000 0x1 0x0 +#define MX50_PAD_I2C1_SCL__UART2_TXD_MUX 0x040 0x2ec 0x7cc 0x2 0x0 +#define MX50_PAD_I2C1_SDA__I2C1_SDA 0x044 0x2f0 0x000 0x0 0x0 +#define MX50_PAD_I2C1_SDA__GPIO6_19 0x044 0x2f0 0x000 0x1 0x0 +#define MX50_PAD_I2C1_SDA__UART2_RXD_MUX 0x044 0x2f0 0x7cc 0x2 0x1 +#define MX50_PAD_I2C2_SCL__I2C2_SCL 0x048 0x2f4 0x000 0x0 0x0 +#define MX50_PAD_I2C2_SCL__GPIO6_20 0x048 0x2f4 0x000 0x1 0x0 +#define MX50_PAD_I2C2_SCL__UART2_CTS 0x048 0x2f4 0x000 0x2 0x0 +#define MX50_PAD_I2C2_SDA__I2C2_SDA 0x04c 0x2f8 0x000 0x0 0x0 +#define MX50_PAD_I2C2_SDA__GPIO6_21 0x04c 0x2f8 0x000 0x1 0x0 +#define MX50_PAD_I2C2_SDA__UART2_RTS 0x04c 0x2f8 0x7c8 0x2 0x1 +#define MX50_PAD_I2C3_SCL__I2C3_SCL 0x050 0x2fc 0x000 0x0 0x0 +#define MX50_PAD_I2C3_SCL__GPIO6_22 0x050 0x2fc 0x000 0x1 0x0 +#define MX50_PAD_I2C3_SCL__FEC_MDC 0x050 0x2fc 0x000 0x2 0x0 +#define MX50_PAD_I2C3_SCL__GPC_PMIC_RDY 0x050 0x2fc 0x000 0x3 0x0 +#define MX50_PAD_I2C3_SCL__GPT_CAPIN1 0x050 0x2fc 0x000 0x5 0x0 +#define MX50_PAD_I2C3_SCL__OBSERVE_MUX_OBSRV_INT_OUT0 0x050 0x2fc 0x000 0x6 0x0 +#define MX50_PAD_I2C3_SCL__USBOH1_USBOTG_OC 0x050 0x2fc 0x7e8 0x7 0x0 +#define MX50_PAD_I2C3_SDA__I2C3_SDA 0x054 0x300 0x000 0x0 0x0 +#define MX50_PAD_I2C3_SDA__GPIO6_23 0x054 0x300 0x000 0x1 0x0 +#define MX50_PAD_I2C3_SDA__FEC_MDIO 0x054 0x300 0x774 0x2 0x0 +#define MX50_PAD_I2C3_SDA__TZIC_PWRFAIL_INT 0x054 0x300 0x000 0x3 0x0 +#define MX50_PAD_I2C3_SDA__SRTC_ALARM_DEB 0x054 0x300 0x000 0x4 0x0 +#define MX50_PAD_I2C3_SDA__GPT_CAPIN2 0x054 0x300 0x000 0x5 0x0 +#define MX50_PAD_I2C3_SDA__OBSERVE_MUX_OBSRV_INT_OUT1 0x054 0x300 0x000 0x6 0x0 +#define MX50_PAD_I2C3_SDA__USBOH1_USBOTG_PWR 0x054 0x300 0x000 0x7 0x0 +#define MX50_PAD_PWM1__PWM1_PWMO 0x058 0x304 0x000 0x0 0x0 +#define MX50_PAD_PWM1__GPIO6_24 0x058 0x304 0x000 0x1 0x0 +#define MX50_PAD_PWM1__USBOH1_USBOTG_OC 0x058 0x304 0x7e8 0x2 0x1 +#define MX50_PAD_PWM1__GPT_CMPOUT1 0x058 0x304 0x000 0x5 0x0 +#define MX50_PAD_PWM1__OBSERVE_MUX_OBSRV_INT_OUT2 0x058 0x304 0x000 0x6 0x0 +#define MX50_PAD_PWM1__SJC_FAIL 0x058 0x304 0x000 0x7 0x0 +#define MX50_PAD_PWM2__PWM2_PWMO 0x05c 0x308 0x000 0x0 0x0 +#define MX50_PAD_PWM2__GPIO6_25 0x05c 0x308 0x000 0x1 0x0 +#define MX50_PAD_PWM2__USBOH1_USBOTG_PWR 0x05c 0x308 0x000 0x2 0x0 +#define MX50_PAD_PWM2__GPT_CMPOUT2 0x05c 0x308 0x000 0x5 0x0 +#define MX50_PAD_PWM2__OBSERVE_MUX_OBSRV_INT_OUT3 0x05c 0x308 0x000 0x6 0x0 +#define MX50_PAD_PWM2__SRC_ANY_PU_RST 0x05c 0x308 0x000 0x7 0x0 +#define MX50_PAD_OWIRE__OWIRE_LINE 0x060 0x30c 0x000 0x0 0x0 +#define MX50_PAD_OWIRE__GPIO6_26 0x060 0x30c 0x000 0x1 0x0 +#define MX50_PAD_OWIRE__USBOH1_USBH1_OC 0x060 0x30c 0x000 0x2 0x0 +#define MX50_PAD_OWIRE__CCM_SSI_EXT1_CLK 0x060 0x30c 0x000 0x3 0x0 +#define MX50_PAD_OWIRE__EPDC_PWRIRQ 0x060 0x30c 0x000 0x4 0x0 +#define MX50_PAD_OWIRE__GPT_CMPOUT3 0x060 0x30c 0x000 0x5 0x0 +#define MX50_PAD_OWIRE__OBSERVE_MUX_OBSRV_INT_OUT4 0x060 0x30c 0x000 0x6 0x0 +#define MX50_PAD_OWIRE__SJC_JTAG_ACT 0x060 0x30c 0x000 0x7 0x0 +#define MX50_PAD_EPITO__EPIT1_EPITO 0x064 0x310 0x000 0x0 0x0 +#define MX50_PAD_EPITO__GPIO6_27 0x064 0x310 0x000 0x1 0x0 +#define MX50_PAD_EPITO__USBOH1_USBH1_PWR 0x064 0x310 0x000 0x2 0x0 +#define MX50_PAD_EPITO__CCM_SSI_EXT2_CLK 0x064 0x310 0x000 0x3 0x0 +#define MX50_PAD_EPITO__DPLLIP1_TOG_EN 0x064 0x310 0x000 0x4 0x0 +#define MX50_PAD_EPITO__GPT_CLK_IN 0x064 0x310 0x000 0x5 0x0 +#define MX50_PAD_EPITO__PMU_IRQ_B 0x064 0x310 0x000 0x6 0x0 +#define MX50_PAD_EPITO__SJC_DE_B 0x064 0x310 0x000 0x7 0x0 +#define MX50_PAD_WDOG__WDOG1_WDOG_B 0x068 0x314 0x000 0x0 0x0 +#define MX50_PAD_WDOG__GPIO6_28 0x068 0x314 0x000 0x1 0x0 +#define MX50_PAD_WDOG__WDOG1_WDOG_RST_B_DEB 0x068 0x314 0x000 0x2 0x0 +#define MX50_PAD_WDOG__CCM_XTAL32K 0x068 0x314 0x000 0x6 0x0 +#define MX50_PAD_WDOG__SJC_DONE 0x068 0x314 0x000 0x7 0x0 +#define MX50_PAD_SSI_TXFS__AUDMUX_AUD3_TXFS 0x06c 0x318 0x000 0x0 0x0 +#define MX50_PAD_SSI_TXFS__GPIO6_0 0x06c 0x318 0x000 0x1 0x0 +#define MX50_PAD_SSI_TXFS__SRC_BT_FUSE_RSV_1 0x06c 0x318 0x000 0x6 0x0 +#define MX50_PAD_SSI_TXFS__USBPHY1_DATAOUT_8 0x06c 0x318 0x000 0x7 0x0 +#define MX50_PAD_SSI_TXC__AUDMUX_AUD3_TXC 0x070 0x31c 0x000 0x0 0x0 +#define MX50_PAD_SSI_TXC__GPIO6_1 0x070 0x31c 0x000 0x1 0x0 +#define MX50_PAD_SSI_TXC__SRC_BT_FUSE_RSV_0 0x070 0x31c 0x000 0x6 0x0 +#define MX50_PAD_SSI_TXC__USBPHY1_DATAOUT_9 0x070 0x31c 0x000 0x7 0x0 +#define MX50_PAD_SSI_TXD__AUDMUX_AUD3_TXD 0x074 0x320 0x000 0x0 0x0 +#define MX50_PAD_SSI_TXD__GPIO6_2 0x074 0x320 0x000 0x1 0x0 +#define MX50_PAD_SSI_TXD__CSPI_RDY 0x074 0x320 0x6e8 0x4 0x0 +#define MX50_PAD_SSI_TXD__USBPHY1_DATAOUT_10 0x074 0x320 0x000 0x7 0x0 +#define MX50_PAD_SSI_RXD__AUDMUX_AUD3_RXD 0x078 0x324 0x000 0x0 0x0 +#define MX50_PAD_SSI_RXD__GPIO6_3 0x078 0x324 0x000 0x1 0x0 +#define MX50_PAD_SSI_RXD__CSPI_SS3 0x078 0x324 0x6f4 0x4 0x0 +#define MX50_PAD_SSI_RXD__USBPHY1_DATAOUT_11 0x078 0x324 0x000 0x7 0x0 +#define MX50_PAD_SSI_RXFS__AUDMUX_AUD3_RXFS 0x07c 0x328 0x000 0x0 0x0 +#define MX50_PAD_SSI_RXFS__GPIO6_4 0x07c 0x328 0x000 0x1 0x0 +#define MX50_PAD_SSI_RXFS__UART5_TXD_MUX 0x07c 0x328 0x7e4 0x2 0x0 +#define MX50_PAD_SSI_RXFS__EIM_WEIM_D_6 0x07c 0x328 0x804 0x3 0x0 +#define MX50_PAD_SSI_RXFS__CSPI_SS2 0x07c 0x328 0x6f0 0x4 0x0 +#define MX50_PAD_SSI_RXFS__FEC_COL 0x07c 0x328 0x770 0x5 0x0 +#define MX50_PAD_SSI_RXFS__FEC_MDC 0x07c 0x328 0x000 0x6 0x0 +#define MX50_PAD_SSI_RXFS__USBPHY1_DATAOUT_12 0x07c 0x328 0x000 0x7 0x0 +#define MX50_PAD_SSI_RXC__AUDMUX_AUD3_RXC 0x080 0x32c 0x000 0x0 0x0 +#define MX50_PAD_SSI_RXC__GPIO6_5 0x080 0x32c 0x000 0x1 0x0 +#define MX50_PAD_SSI_RXC__UART5_RXD_MUX 0x080 0x32c 0x7e4 0x2 0x1 +#define MX50_PAD_SSI_RXC__EIM_WEIM_D_7 0x080 0x32c 0x808 0x3 0x0 +#define MX50_PAD_SSI_RXC__CSPI_SS1 0x080 0x32c 0x6ec 0x4 0x0 +#define MX50_PAD_SSI_RXC__FEC_RX_CLK 0x080 0x32c 0x780 0x5 0x0 +#define MX50_PAD_SSI_RXC__FEC_MDIO 0x080 0x32c 0x774 0x6 0x1 +#define MX50_PAD_SSI_RXC__USBPHY1_DATAOUT_13 0x080 0x32c 0x000 0x7 0x0 +#define MX50_PAD_UART1_TXD__UART1_TXD_MUX 0x084 0x330 0x7c4 0x0 0x0 +#define MX50_PAD_UART1_TXD__GPIO6_6 0x084 0x330 0x000 0x1 0x0 +#define MX50_PAD_UART1_TXD__USBPHY1_DATAOUT_14 0x084 0x330 0x000 0x7 0x0 +#define MX50_PAD_UART1_RXD__UART1_RXD_MUX 0x088 0x334 0x7c4 0x0 0x1 +#define MX50_PAD_UART1_RXD__GPIO6_7 0x088 0x334 0x000 0x1 0x0 +#define MX50_PAD_UART1_RXD__USBPHY1_DATAOUT_15 0x088 0x334 0x000 0x7 0x0 +#define MX50_PAD_UART1_CTS__UART1_CTS 0x08c 0x338 0x000 0x0 0x0 +#define MX50_PAD_UART1_CTS__GPIO6_8 0x08c 0x338 0x000 0x1 0x0 +#define MX50_PAD_UART1_CTS__UART5_TXD_MUX 0x08c 0x338 0x7e4 0x2 0x2 +#define MX50_PAD_UART1_CTS__ESDHC4_DAT4 0x08c 0x338 0x760 0x4 0x0 +#define MX50_PAD_UART1_CTS__ESDHC4_CMD 0x08c 0x338 0x74c 0x5 0x0 +#define MX50_PAD_UART1_CTS__USBPHY2_DATAOUT_8 0x08c 0x338 0x000 0x7 0x0 +#define MX50_PAD_UART1_RTS__UART1_RTS 0x090 0x33c 0x7c0 0x0 0x3 +#define MX50_PAD_UART1_RTS__GPIO6_9 0x090 0x33c 0x000 0x1 0x0 +#define MX50_PAD_UART1_RTS__UART5_RXD_MUX 0x090 0x33c 0x7e4 0x2 0x3 +#define MX50_PAD_UART1_RTS__ESDHC4_DAT5 0x090 0x33c 0x764 0x4 0x0 +#define MX50_PAD_UART1_RTS__ESDHC4_CLK 0x090 0x33c 0x748 0x5 0x0 +#define MX50_PAD_UART1_RTS__USBPHY2_DATAOUT_9 0x090 0x33c 0x000 0x7 0x0 +#define MX50_PAD_UART2_TXD__UART2_TXD_MUX 0x094 0x340 0x7cc 0x0 0x2 +#define MX50_PAD_UART2_TXD__GPIO6_10 0x094 0x340 0x000 0x1 0x0 +#define MX50_PAD_UART2_TXD__ESDHC4_DAT6 0x094 0x340 0x768 0x4 0x0 +#define MX50_PAD_UART2_TXD__ESDHC4_DAT4 0x094 0x340 0x760 0x5 0x1 +#define MX50_PAD_UART2_TXD__USBPHY2_DATAOUT_10 0x094 0x340 0x000 0x7 0x0 +#define MX50_PAD_UART2_RXD__UART2_RXD_MUX 0x098 0x344 0x7cc 0x0 0x3 +#define MX50_PAD_UART2_RXD__GPIO6_11 0x098 0x344 0x000 0x1 0x0 +#define MX50_PAD_UART2_RXD__ESDHC4_DAT7 0x098 0x344 0x76c 0x4 0x0 +#define MX50_PAD_UART2_RXD__ESDHC4_DAT5 0x098 0x344 0x764 0x5 0x1 +#define MX50_PAD_UART2_RXD__USBPHY2_DATAOUT_11 0x098 0x344 0x000 0x7 0x0 +#define MX50_PAD_UART2_CTS__UART2_CTS 0x09c 0x348 0x000 0x0 0x0 +#define MX50_PAD_UART2_CTS__GPIO6_12 0x09c 0x348 0x000 0x1 0x0 +#define MX50_PAD_UART2_CTS__ESDHC4_CMD 0x09c 0x348 0x74c 0x4 0x1 +#define MX50_PAD_UART2_CTS__ESDHC4_DAT6 0x09c 0x348 0x768 0x5 0x1 +#define MX50_PAD_UART2_CTS__USBPHY2_DATAOUT_12 0x09c 0x348 0x000 0x7 0x0 +#define MX50_PAD_UART2_RTS__UART2_RTS 0x0a0 0x34c 0x7c8 0x0 0x2 +#define MX50_PAD_UART2_RTS__GPIO6_13 0x0a0 0x34c 0x000 0x1 0x0 +#define MX50_PAD_UART2_RTS__ESDHC4_CLK 0x0a0 0x34c 0x748 0x4 0x1 +#define MX50_PAD_UART2_RTS__ESDHC4_DAT7 0x0a0 0x34c 0x76c 0x5 0x1 +#define MX50_PAD_UART2_RTS__USBPHY2_DATAOUT_13 0x0a0 0x34c 0x000 0x7 0x0 +#define MX50_PAD_UART3_TXD__UART3_TXD_MUX 0x0a4 0x350 0x7d4 0x0 0x0 +#define MX50_PAD_UART3_TXD__GPIO6_14 0x0a4 0x350 0x000 0x1 0x0 +#define MX50_PAD_UART3_TXD__ESDHC1_DAT4 0x0a4 0x350 0x000 0x3 0x0 +#define MX50_PAD_UART3_TXD__ESDHC4_DAT0 0x0a4 0x350 0x000 0x4 0x0 +#define MX50_PAD_UART3_TXD__ESDHC2_WP 0x0a4 0x350 0x744 0x5 0x0 +#define MX50_PAD_UART3_TXD__EIM_WEIM_D_12 0x0a4 0x350 0x81c 0x6 0x0 +#define MX50_PAD_UART3_TXD__USBPHY2_DATAOUT_14 0x0a4 0x350 0x000 0x7 0x0 +#define MX50_PAD_UART3_RXD__UART3_RXD_MUX 0x0a8 0x354 0x7d4 0x0 0x1 +#define MX50_PAD_UART3_RXD__GPIO6_15 0x0a8 0x354 0x000 0x1 0x0 +#define MX50_PAD_UART3_RXD__ESDHC1_DAT5 0x0a8 0x354 0x000 0x3 0x0 +#define MX50_PAD_UART3_RXD__ESDHC4_DAT1 0x0a8 0x354 0x754 0x4 0x0 +#define MX50_PAD_UART3_RXD__ESDHC2_CD 0x0a8 0x354 0x740 0x5 0x0 +#define MX50_PAD_UART3_RXD__EIM_WEIM_D_13 0x0a8 0x354 0x820 0x6 0x0 +#define MX50_PAD_UART3_RXD__USBPHY2_DATAOUT_15 0x0a8 0x354 0x000 0x7 0x0 +#define MX50_PAD_UART4_TXD__UART4_TXD_MUX 0x0ac 0x358 0x7dc 0x0 0x0 +#define MX50_PAD_UART4_TXD__GPIO6_16 0x0ac 0x358 0x000 0x1 0x0 +#define MX50_PAD_UART4_TXD__UART3_CTS 0x0ac 0x358 0x7d0 0x2 0x0 +#define MX50_PAD_UART4_TXD__ESDHC1_DAT6 0x0ac 0x358 0x000 0x3 0x0 +#define MX50_PAD_UART4_TXD__ESDHC4_DAT2 0x0ac 0x358 0x758 0x4 0x0 +#define MX50_PAD_UART4_TXD__ESDHC2_LCTL 0x0ac 0x358 0x000 0x5 0x0 +#define MX50_PAD_UART4_TXD__EIM_WEIM_D_14 0x0ac 0x358 0x824 0x6 0x0 +#define MX50_PAD_UART4_RXD__UART4_RXD_MUX 0x0b0 0x35c 0x7dc 0x0 0x1 +#define MX50_PAD_UART4_RXD__GPIO6_17 0x0b0 0x35c 0x000 0x1 0x0 +#define MX50_PAD_UART4_RXD__UART3_RTS 0x0b0 0x35c 0x7d0 0x2 0x1 +#define MX50_PAD_UART4_RXD__ESDHC1_DAT7 0x0b0 0x35c 0x000 0x3 0x0 +#define MX50_PAD_UART4_RXD__ESDHC4_DAT3 0x0b0 0x35c 0x75c 0x4 0x0 +#define MX50_PAD_UART4_RXD__ESDHC1_LCTL 0x0b0 0x35c 0x000 0x5 0x0 +#define MX50_PAD_UART4_RXD__EIM_WEIM_D_15 0x0b0 0x35c 0x828 0x6 0x0 +#define MX50_PAD_CSPI_SCLK__CSPI_SCLK 0x0b4 0x360 0x000 0x0 0x0 +#define MX50_PAD_CSPI_SCLK__GPIO4_8 0x0b4 0x360 0x000 0x1 0x0 +#define MX50_PAD_CSPI_MOSI__CSPI_MOSI 0x0b8 0x364 0x000 0x0 0x0 +#define MX50_PAD_CSPI_MOSI__GPIO4_9 0x0b8 0x364 0x000 0x1 0x0 +#define MX50_PAD_CSPI_MISO__CSPI_MISO 0x0bc 0x368 0x000 0x0 0x0 +#define MX50_PAD_CSPI_MISO__GPIO4_10 0x0bc 0x368 0x000 0x1 0x0 +#define MX50_PAD_CSPI_SS0__CSPI_SS0 0x0c0 0x36c 0x000 0x0 0x0 +#define MX50_PAD_CSPI_SS0__GPIO4_11 0x0c0 0x36c 0x000 0x1 0x0 +#define MX50_PAD_ECSPI1_SCLK__ECSPI1_SCLK 0x0c4 0x370 0x000 0x0 0x0 +#define MX50_PAD_ECSPI1_SCLK__GPIO4_12 0x0c4 0x370 0x000 0x1 0x0 +#define MX50_PAD_ECSPI1_SCLK__CSPI_RDY 0x0c4 0x370 0x6e8 0x2 0x1 +#define MX50_PAD_ECSPI1_SCLK__ECSPI2_RDY 0x0c4 0x370 0x000 0x3 0x0 +#define MX50_PAD_ECSPI1_SCLK__UART3_RTS 0x0c4 0x370 0x7d0 0x4 0x2 +#define MX50_PAD_ECSPI1_SCLK__EPDC_SDCE_6 0x0c4 0x370 0x000 0x5 0x0 +#define MX50_PAD_ECSPI1_SCLK__EIM_WEIM_D_8 0x0c4 0x370 0x80c 0x7 0x0 +#define MX50_PAD_ECSPI1_MOSI__ECSPI1_MOSI 0x0c8 0x374 0x000 0x0 0x0 +#define MX50_PAD_ECSPI1_MOSI__GPIO4_13 0x0c8 0x374 0x000 0x1 0x0 +#define MX50_PAD_ECSPI1_MOSI__CSPI_SS1 0x0c8 0x374 0x6ec 0x2 0x1 +#define MX50_PAD_ECSPI1_MOSI__ECSPI2_SS1 0x0c8 0x374 0x000 0x3 0x0 +#define MX50_PAD_ECSPI1_MOSI__UART3_CTS 0x0c8 0x374 0x000 0x4 0x0 +#define MX50_PAD_ECSPI1_MOSI__EPDC_SDCE_7 0x0c8 0x374 0x000 0x5 0x0 +#define MX50_PAD_ECSPI1_MOSI__EIM_WEIM_D_9 0x0c8 0x374 0x810 0x7 0x0 +#define MX50_PAD_ECSPI1_MISO__ECSPI1_MISO 0x0cc 0x378 0x000 0x0 0x0 +#define MX50_PAD_ECSPI1_MISO__GPIO4_14 0x0cc 0x378 0x000 0x1 0x0 +#define MX50_PAD_ECSPI1_MISO__CSPI_SS2 0x0cc 0x378 0x6f0 0x2 0x1 +#define MX50_PAD_ECSPI1_MISO__ECSPI2_SS2 0x0cc 0x378 0x000 0x3 0x0 +#define MX50_PAD_ECSPI1_MISO__UART4_RTS 0x0cc 0x378 0x7d8 0x4 0x0 +#define MX50_PAD_ECSPI1_MISO__EPDC_SDCE_8 0x0cc 0x378 0x000 0x5 0x0 +#define MX50_PAD_ECSPI1_MISO__EIM_WEIM_D_10 0x0cc 0x378 0x814 0x7 0x0 +#define MX50_PAD_ECSPI1_SS0__ECSPI1_SS0 0x0d0 0x37c 0x000 0x0 0x0 +#define MX50_PAD_ECSPI1_SS0__GPIO4_15 0x0d0 0x37c 0x000 0x1 0x0 +#define MX50_PAD_ECSPI1_SS0__CSPI_SS3 0x0d0 0x37c 0x6f4 0x2 0x1 +#define MX50_PAD_ECSPI1_SS0__ECSPI2_SS3 0x0d0 0x37c 0x000 0x3 0x0 +#define MX50_PAD_ECSPI1_SS0__UART4_CTS 0x0d0 0x37c 0x000 0x4 0x0 +#define MX50_PAD_ECSPI1_SS0__EPDC_SDCE_9 0x0d0 0x37c 0x000 0x5 0x0 +#define MX50_PAD_ECSPI1_SS0__EIM_WEIM_D_11 0x0d0 0x37c 0x818 0x7 0x0 +#define MX50_PAD_ECSPI2_SCLK__ECSPI2_SCLK 0x0d4 0x380 0x000 0x0 0x0 +#define MX50_PAD_ECSPI2_SCLK__GPIO4_16 0x0d4 0x380 0x000 0x1 0x0 +#define MX50_PAD_ECSPI2_SCLK__ELCDIF_WR_RWN 0x0d4 0x380 0x000 0x2 0x0 +#define MX50_PAD_ECSPI2_SCLK__ECSPI1_RDY 0x0d4 0x380 0x000 0x3 0x0 +#define MX50_PAD_ECSPI2_SCLK__UART5_RTS 0x0d4 0x380 0x7e0 0x4 0x0 +#define MX50_PAD_ECSPI2_SCLK__ELCDIF_DOTCLK 0x0d4 0x380 0x000 0x5 0x0 +#define MX50_PAD_ECSPI2_SCLK__EIM_NANDF_CEN_4 0x0d4 0x380 0x000 0x6 0x0 +#define MX50_PAD_ECSPI2_SCLK__EIM_WEIM_D_8 0x0d4 0x380 0x80c 0x7 0x1 +#define MX50_PAD_ECSPI2_MOSI__ECSPI2_MOSI 0x0d8 0x384 0x000 0x0 0x0 +#define MX50_PAD_ECSPI2_MOSI__GPIO4_17 0x0d8 0x384 0x000 0x1 0x0 +#define MX50_PAD_ECSPI2_MOSI__ELCDIF_RE_E 0x0d8 0x384 0x000 0x2 0x0 +#define MX50_PAD_ECSPI2_MOSI__ECSPI1_SS1 0x0d8 0x384 0x000 0x3 0x0 +#define MX50_PAD_ECSPI2_MOSI__UART5_CTS 0x0d8 0x384 0x7e0 0x4 0x1 +#define MX50_PAD_ECSPI2_MOSI__ELCDIF_ENABLE 0x0d8 0x384 0x000 0x5 0x0 +#define MX50_PAD_ECSPI2_MOSI__EIM_NANDF_CEN_5 0x0d8 0x384 0x000 0x6 0x0 +#define MX50_PAD_ECSPI2_MOSI__EIM_WEIM_D_9 0x0d8 0x384 0x810 0x7 0x1 +#define MX50_PAD_ECSPI2_MISO__ECSPI2_MISO 0x0dc 0x388 0x000 0x0 0x0 +#define MX50_PAD_ECSPI2_MISO__GPIO4_18 0x0dc 0x388 0x000 0x1 0x0 +#define MX50_PAD_ECSPI2_MISO__ELCDIF_RS 0x0dc 0x388 0x000 0x2 0x0 +#define MX50_PAD_ECSPI2_MISO__ECSPI1_SS2 0x0dc 0x388 0x000 0x3 0x0 +#define MX50_PAD_ECSPI2_MISO__UART5_TXD_MUX 0x0dc 0x388 0x7e4 0x4 0x4 +#define MX50_PAD_ECSPI2_MISO__ELCDIF_VSYNC 0x0dc 0x388 0x73c 0x5 0x0 +#define MX50_PAD_ECSPI2_MISO__EIM_NANDF_CEN_6 0x0dc 0x388 0x000 0x6 0x0 +#define MX50_PAD_ECSPI2_MISO__EIM_WEIM_D_10 0x0dc 0x388 0x814 0x7 0x1 +#define MX50_PAD_ECSPI2_SS0__ECSPI2_SS0 0x0e0 0x38c 0x000 0x0 0x0 +#define MX50_PAD_ECSPI2_SS0__GPIO4_19 0x0e0 0x38c 0x000 0x1 0x0 +#define MX50_PAD_ECSPI2_SS0__ELCDIF_CS 0x0e0 0x38c 0x000 0x2 0x0 +#define MX50_PAD_ECSPI2_SS0__ECSPI2_SS3 0x0e0 0x38c 0x000 0x3 0x0 +#define MX50_PAD_ECSPI2_SS0__UART5_RXD_MUX 0x0e0 0x38c 0x7e4 0x4 0x5 +#define MX50_PAD_ECSPI2_SS0__ELCDIF_HSYNC 0x0e0 0x38c 0x6f8 0x5 0x0 +#define MX50_PAD_ECSPI2_SS0__EIM_NANDF_CEN_7 0x0e0 0x38c 0x000 0x6 0x0 +#define MX50_PAD_ECSPI2_SS0__EIM_WEIM_D_11 0x0e0 0x38c 0x818 0x7 0x1 +#define MX50_PAD_SD1_CLK__ESDHC1_CLK 0x0e4 0x390 0x000 0x0 0x0 +#define MX50_PAD_SD1_CLK__GPIO5_0 0x0e4 0x390 0x000 0x1 0x0 +#define MX50_PAD_SD1_CLK__CCM_CLKO 0x0e4 0x390 0x000 0x7 0x0 +#define MX50_PAD_SD1_CMD__ESDHC1_CMD 0x0e8 0x394 0x000 0x0 0x0 +#define MX50_PAD_SD1_CMD__GPIO5_1 0x0e8 0x394 0x000 0x1 0x0 +#define MX50_PAD_SD1_CMD__CCM_CLKO2 0x0e8 0x394 0x000 0x7 0x0 +#define MX50_PAD_SD1_D0__ESDHC1_DAT0 0x0ec 0x398 0x000 0x0 0x0 +#define MX50_PAD_SD1_D0__GPIO5_2 0x0ec 0x398 0x000 0x1 0x0 +#define MX50_PAD_SD1_D0__CCM_PLL1_BYP 0x0ec 0x398 0x6dc 0x7 0x0 +#define MX50_PAD_SD1_D1__ESDHC1_DAT1 0x0f0 0x39c 0x000 0x0 0x0 +#define MX50_PAD_SD1_D1__GPIO5_3 0x0f0 0x39c 0x000 0x1 0x0 +#define MX50_PAD_SD1_D1__CCM_PLL2_BYP 0x0f0 0x39c 0x000 0x7 0x0 +#define MX50_PAD_SD1_D2__ESDHC1_DAT2 0x0f4 0x3a0 0x000 0x0 0x0 +#define MX50_PAD_SD1_D2__GPIO5_4 0x0f4 0x3a0 0x000 0x1 0x0 +#define MX50_PAD_SD1_D2__CCM_PLL3_BYP 0x0f4 0x3a0 0x6e4 0x7 0x0 +#define MX50_PAD_SD1_D3__ESDHC1_DAT3 0x0f8 0x3a4 0x000 0x0 0x0 +#define MX50_PAD_SD1_D3__GPIO5_5 0x0f8 0x3a4 0x000 0x1 0x0 +#define MX50_PAD_SD2_CLK__ESDHC2_CLK 0x0fc 0x3a8 0x000 0x0 0x0 +#define MX50_PAD_SD2_CLK__GPIO5_6 0x0fc 0x3a8 0x000 0x1 0x0 +#define MX50_PAD_SD2_CLK__MSHC_SCLK 0x0fc 0x3a8 0x000 0x2 0x0 +#define MX50_PAD_SD2_CMD__ESDHC2_CMD 0x100 0x3ac 0x000 0x0 0x0 +#define MX50_PAD_SD2_CMD__GPIO5_7 0x100 0x3ac 0x000 0x1 0x0 +#define MX50_PAD_SD2_CMD__MSHC_BS 0x100 0x3ac 0x000 0x2 0x0 +#define MX50_PAD_SD2_D0__ESDHC2_DAT0 0x104 0x3b0 0x000 0x0 0x0 +#define MX50_PAD_SD2_D0__GPIO5_8 0x104 0x3b0 0x000 0x1 0x0 +#define MX50_PAD_SD2_D0__MSHC_DATA_0 0x104 0x3b0 0x000 0x2 0x0 +#define MX50_PAD_SD2_D0__KPP_COL_4 0x104 0x3b0 0x790 0x3 0x0 +#define MX50_PAD_SD2_D1__ESDHC2_DAT1 0x108 0x3b4 0x000 0x0 0x0 +#define MX50_PAD_SD2_D1__GPIO5_9 0x108 0x3b4 0x000 0x1 0x0 +#define MX50_PAD_SD2_D1__MSHC_DATA_1 0x108 0x3b4 0x000 0x2 0x0 +#define MX50_PAD_SD2_D1__KPP_ROW_4 0x108 0x3b4 0x7a0 0x3 0x0 +#define MX50_PAD_SD2_D2__ESDHC2_DAT2 0x10c 0x3b8 0x000 0x0 0x0 +#define MX50_PAD_SD2_D2__GPIO5_10 0x10c 0x3b8 0x000 0x1 0x0 +#define MX50_PAD_SD2_D2__MSHC_DATA_2 0x10c 0x3b8 0x000 0x2 0x0 +#define MX50_PAD_SD2_D2__KPP_COL_5 0x10c 0x3b8 0x794 0x3 0x0 +#define MX50_PAD_SD2_D3__ESDHC2_DAT3 0x110 0x3bc 0x000 0x0 0x0 +#define MX50_PAD_SD2_D3__GPIO5_11 0x110 0x3bc 0x000 0x1 0x0 +#define MX50_PAD_SD2_D3__MSHC_DATA_3 0x110 0x3bc 0x000 0x2 0x0 +#define MX50_PAD_SD2_D3__KPP_ROW_5 0x110 0x3bc 0x7a4 0x3 0x0 +#define MX50_PAD_SD2_D4__ESDHC2_DAT4 0x114 0x3c0 0x000 0x0 0x0 +#define MX50_PAD_SD2_D4__GPIO5_12 0x114 0x3c0 0x000 0x1 0x0 +#define MX50_PAD_SD2_D4__AUDMUX_AUD4_RXFS 0x114 0x3c0 0x6d0 0x2 0x0 +#define MX50_PAD_SD2_D4__KPP_COL_6 0x114 0x3c0 0x798 0x3 0x0 +#define MX50_PAD_SD2_D4__EIM_WEIM_D_0 0x114 0x3c0 0x7ec 0x4 0x0 +#define MX50_PAD_SD2_D4__CCM_CCM_OUT_0 0x114 0x3c0 0x000 0x7 0x0 +#define MX50_PAD_SD2_D5__ESDHC2_DAT5 0x118 0x3c4 0x000 0x0 0x0 +#define MX50_PAD_SD2_D5__GPIO5_13 0x118 0x3c4 0x000 0x1 0x0 +#define MX50_PAD_SD2_D5__AUDMUX_AUD4_RXC 0x118 0x3c4 0x6cc 0x2 0x0 +#define MX50_PAD_SD2_D5__KPP_ROW_6 0x118 0x3c4 0x7a8 0x3 0x0 +#define MX50_PAD_SD2_D5__EIM_WEIM_D_1 0x118 0x3c4 0x7f0 0x4 0x0 +#define MX50_PAD_SD2_D5__CCM_CCM_OUT_1 0x118 0x3c4 0x000 0x7 0x0 +#define MX50_PAD_SD2_D6__ESDHC2_DAT6 0x11c 0x3c8 0x000 0x0 0x0 +#define MX50_PAD_SD2_D6__GPIO5_14 0x11c 0x3c8 0x000 0x1 0x0 +#define MX50_PAD_SD2_D6__AUDMUX_AUD4_RXD 0x11c 0x3c8 0x6c4 0x2 0x0 +#define MX50_PAD_SD2_D6__KPP_COL_7 0x11c 0x3c8 0x79c 0x3 0x0 +#define MX50_PAD_SD2_D6__EIM_WEIM_D_2 0x11c 0x3c8 0x7f4 0x4 0x0 +#define MX50_PAD_SD2_D6__CCM_CCM_OUT_2 0x11c 0x3c8 0x000 0x7 0x0 +#define MX50_PAD_SD2_D7__ESDHC2_DAT7 0x120 0x3cc 0x000 0x0 0x0 +#define MX50_PAD_SD2_D7__GPIO5_15 0x120 0x3cc 0x000 0x1 0x0 +#define MX50_PAD_SD2_D7__AUDMUX_AUD4_TXFS 0x120 0x3cc 0x6d8 0x2 0x0 +#define MX50_PAD_SD2_D7__KPP_ROW_7 0x120 0x3cc 0x7ac 0x3 0x0 +#define MX50_PAD_SD2_D7__EIM_WEIM_D_3 0x120 0x3cc 0x7f8 0x4 0x0 +#define MX50_PAD_SD2_D7__CCM_STOP 0x120 0x3cc 0x000 0x7 0x0 +#define MX50_PAD_SD2_WP__ESDHC2_WP 0x124 0x3d0 0x744 0x0 0x1 +#define MX50_PAD_SD2_WP__GPIO5_16 0x124 0x3d0 0x000 0x1 0x0 +#define MX50_PAD_SD2_WP__AUDMUX_AUD4_TXD 0x124 0x3d0 0x6c8 0x2 0x0 +#define MX50_PAD_SD2_WP__EIM_WEIM_D_4 0x124 0x3d0 0x7fc 0x4 0x0 +#define MX50_PAD_SD2_WP__CCM_WAIT 0x124 0x3d0 0x000 0x7 0x0 +#define MX50_PAD_SD2_CD__ESDHC2_CD 0x128 0x3d4 0x740 0x0 0x1 +#define MX50_PAD_SD2_CD__GPIO5_17 0x128 0x3d4 0x000 0x1 0x0 +#define MX50_PAD_SD2_CD__AUDMUX_AUD4_TXC 0x128 0x3d4 0x6d4 0x2 0x0 +#define MX50_PAD_SD2_CD__EIM_WEIM_D_5 0x128 0x3d4 0x800 0x4 0x0 +#define MX50_PAD_SD2_CD__CCM_REF_EN_B 0x128 0x3d4 0x000 0x7 0x0 +#define MX50_PAD_DISP_D0__ELCDIF_DAT_0 0x12c 0x40c 0x6fc 0x0 0x0 +#define MX50_PAD_DISP_D0__GPIO2_0 0x12c 0x40c 0x000 0x1 0x0 +#define MX50_PAD_DISP_D0__FEC_TX_CLK 0x12c 0x40c 0x78c 0x2 0x0 +#define MX50_PAD_DISP_D0__EIM_WEIM_A_16 0x12c 0x40c 0x000 0x3 0x0 +#define MX50_PAD_DISP_D0__SDMA_DEBUG_PC_0 0x12c 0x40c 0x000 0x6 0x0 +#define MX50_PAD_DISP_D0__USBPHY1_VSTATUS_0 0x12c 0x40c 0x000 0x7 0x0 +#define MX50_PAD_DISP_D1__ELCDIF_DAT_1 0x130 0x410 0x700 0x0 0x0 +#define MX50_PAD_DISP_D1__GPIO2_1 0x130 0x410 0x000 0x1 0x0 +#define MX50_PAD_DISP_D1__FEC_RX_ERR 0x130 0x410 0x788 0x2 0x0 +#define MX50_PAD_DISP_D1__EIM_WEIM_A_17 0x130 0x410 0x000 0x3 0x0 +#define MX50_PAD_DISP_D1__SDMA_DEBUG_PC_1 0x130 0x410 0x000 0x6 0x0 +#define MX50_PAD_DISP_D1__USBPHY1_VSTATUS_1 0x130 0x410 0x000 0x7 0x0 +#define MX50_PAD_DISP_D2__ELCDIF_DAT_2 0x134 0x414 0x704 0x0 0x0 +#define MX50_PAD_DISP_D2__GPIO2_2 0x134 0x414 0x000 0x1 0x0 +#define MX50_PAD_DISP_D2__FEC_RX_DV 0x134 0x414 0x784 0x2 0x0 +#define MX50_PAD_DISP_D2__EIM_WEIM_A_18 0x134 0x414 0x000 0x3 0x0 +#define MX50_PAD_DISP_D2__SDMA_DEBUG_PC_2 0x134 0x414 0x000 0x6 0x0 +#define MX50_PAD_DISP_D2__USBPHY1_VSTATUS_2 0x134 0x414 0x000 0x7 0x0 +#define MX50_PAD_DISP_D3__ELCDIF_DAT_3 0x138 0x418 0x708 0x0 0x0 +#define MX50_PAD_DISP_D3__GPIO2_3 0x138 0x418 0x000 0x1 0x0 +#define MX50_PAD_DISP_D3__FEC_RDATA_1 0x138 0x418 0x77c 0x2 0x0 +#define MX50_PAD_DISP_D3__EIM_WEIM_A_19 0x138 0x418 0x000 0x3 0x0 +#define MX50_PAD_DISP_D3__FEC_COL 0x138 0x418 0x770 0x4 0x1 +#define MX50_PAD_DISP_D3__SDMA_DEBUG_PC_3 0x138 0x418 0x000 0x6 0x0 +#define MX50_PAD_DISP_D3__USBPHY1_VSTATUS_3 0x138 0x418 0x000 0x7 0x0 +#define MX50_PAD_DISP_D4__ELCDIF_DAT_4 0x13c 0x41c 0x70c 0x0 0x0 +#define MX50_PAD_DISP_D4__GPIO2_4 0x13c 0x41c 0x000 0x1 0x0 +#define MX50_PAD_DISP_D4__FEC_RDATA_0 0x13c 0x41c 0x778 0x2 0x0 +#define MX50_PAD_DISP_D4__EIM_WEIM_A_20 0x13c 0x41c 0x000 0x3 0x0 +#define MX50_PAD_DISP_D4__SDMA_DEBUG_PC_4 0x13c 0x41c 0x000 0x6 0x0 +#define MX50_PAD_DISP_D4__USBPHY1_VSTATUS_4 0x13c 0x41c 0x000 0x7 0x0 +#define MX50_PAD_DISP_D5__ELCDIF_DAT_5 0x140 0x420 0x710 0x0 0x0 +#define MX50_PAD_DISP_D5__GPIO2_5 0x140 0x420 0x000 0x1 0x0 +#define MX50_PAD_DISP_D5__FEC_TX_EN 0x140 0x420 0x000 0x2 0x0 +#define MX50_PAD_DISP_D5__EIM_WEIM_A_21 0x140 0x420 0x000 0x3 0x0 +#define MX50_PAD_DISP_D5__SDMA_DEBUG_PC_5 0x140 0x420 0x000 0x6 0x0 +#define MX50_PAD_DISP_D5__USBPHY1_VSTATUS_5 0x140 0x420 0x000 0x7 0x0 +#define MX50_PAD_DISP_D6__ELCDIF_DAT_6 0x144 0x424 0x714 0x0 0x0 +#define MX50_PAD_DISP_D6__GPIO2_6 0x144 0x424 0x000 0x1 0x0 +#define MX50_PAD_DISP_D6__FEC_TDATA_1 0x144 0x424 0x000 0x2 0x0 +#define MX50_PAD_DISP_D6__EIM_WEIM_A_22 0x144 0x424 0x000 0x3 0x0 +#define MX50_PAD_DISP_D6__FEC_RX_CLK 0x144 0x424 0x780 0x4 0x1 +#define MX50_PAD_DISP_D6__SDMA_DEBUG_PC_6 0x144 0x424 0x000 0x6 0x0 +#define MX50_PAD_DISP_D6__USBPHY1_VSTATUS_6 0x144 0x424 0x000 0x7 0x0 +#define MX50_PAD_DISP_D7__ELCDIF_DAT_7 0x148 0x428 0x718 0x0 0x0 +#define MX50_PAD_DISP_D7__GPIO2_7 0x148 0x428 0x000 0x1 0x0 +#define MX50_PAD_DISP_D7__FEC_TDATA_0 0x148 0x428 0x000 0x2 0x0 +#define MX50_PAD_DISP_D7__EIM_WEIM_A_23 0x148 0x428 0x000 0x3 0x0 +#define MX50_PAD_DISP_D7__SDMA_DEBUG_PC_7 0x148 0x428 0x000 0x6 0x0 +#define MX50_PAD_DISP_D7__USBPHY1_VSTATUS_7 0x148 0x428 0x000 0x7 0x0 +#define MX50_PAD_DISP_WR__ELCDIF_WR_RWN 0x14c 0x42c 0x000 0x0 0x0 +#define MX50_PAD_DISP_WR__GPIO2_16 0x14c 0x42c 0x000 0x1 0x0 +#define MX50_PAD_DISP_WR__ELCDIF_DOTCLK 0x14c 0x42c 0x000 0x2 0x0 +#define MX50_PAD_DISP_WR__EIM_WEIM_A_24 0x14c 0x42c 0x000 0x3 0x0 +#define MX50_PAD_DISP_WR__SDMA_DEBUG_PC_8 0x14c 0x42c 0x000 0x6 0x0 +#define MX50_PAD_DISP_WR__USBPHY1_AVALID 0x14c 0x42c 0x000 0x7 0x0 +#define MX50_PAD_DISP_RD__ELCDIF_RD_E 0x150 0x430 0x000 0x0 0x0 +#define MX50_PAD_DISP_RD__GPIO2_19 0x150 0x430 0x000 0x1 0x0 +#define MX50_PAD_DISP_RD__ELCDIF_ENABLE 0x150 0x430 0x000 0x2 0x0 +#define MX50_PAD_DISP_RD__EIM_WEIM_A_25 0x150 0x430 0x000 0x3 0x0 +#define MX50_PAD_DISP_RD__SDMA_DEBUG_PC_9 0x150 0x430 0x000 0x6 0x0 +#define MX50_PAD_DISP_RD__USBPHY1_BVALID 0x150 0x430 0x000 0x7 0x0 +#define MX50_PAD_DISP_RS__ELCDIF_RS 0x154 0x434 0x000 0x0 0x0 +#define MX50_PAD_DISP_RS__GPIO2_17 0x154 0x434 0x000 0x1 0x0 +#define MX50_PAD_DISP_RS__ELCDIF_VSYNC 0x154 0x434 0x73c 0x2 0x1 +#define MX50_PAD_DISP_RS__EIM_WEIM_A_26 0x154 0x434 0x000 0x3 0x0 +#define MX50_PAD_DISP_RS__SDMA_DEBUG_PC_10 0x154 0x434 0x000 0x6 0x0 +#define MX50_PAD_DISP_RS__USBPHY1_ENDSESSION 0x154 0x434 0x000 0x7 0x0 +#define MX50_PAD_DISP_CS__ELCDIF_CS 0x158 0x438 0x000 0x0 0x0 +#define MX50_PAD_DISP_CS__GPIO2_21 0x158 0x438 0x000 0x1 0x0 +#define MX50_PAD_DISP_CS__ELCDIF_HSYNC 0x158 0x438 0x6f8 0x2 0x1 +#define MX50_PAD_DISP_CS__EIM_WEIM_A_27 0x158 0x438 0x000 0x3 0x0 +#define MX50_PAD_DISP_CS__EIM_WEIM_CS_3 0x158 0x438 0x000 0x4 0x0 +#define MX50_PAD_DISP_CS__SDMA_DEBUG_PC_11 0x158 0x438 0x000 0x6 0x0 +#define MX50_PAD_DISP_CS__USBPHY1_IDDIG 0x158 0x438 0x000 0x7 0x0 +#define MX50_PAD_DISP_BUSY__ELCDIF_BUSY 0x15c 0x43c 0x6f8 0x0 0x2 +#define MX50_PAD_DISP_BUSY__GPIO2_18 0x15c 0x43c 0x000 0x1 0x0 +#define MX50_PAD_DISP_BUSY__EIM_WEIM_CS_3 0x15c 0x43c 0x000 0x4 0x0 +#define MX50_PAD_DISP_BUSY__SDMA_DEBUG_PC_12 0x15c 0x43c 0x000 0x6 0x0 +#define MX50_PAD_DISP_BUSY__USBPHY2_HOSTDISCONNECT 0x15c 0x43c 0x000 0x7 0x0 +#define MX50_PAD_DISP_RESET__ELCDIF_RESET 0x160 0x440 0x000 0x0 0x0 +#define MX50_PAD_DISP_RESET__GPIO2_20 0x160 0x440 0x000 0x1 0x0 +#define MX50_PAD_DISP_RESET__EIM_WEIM_CS_3 0x160 0x440 0x000 0x4 0x0 +#define MX50_PAD_DISP_RESET__SDMA_DEBUG_PC_13 0x160 0x440 0x000 0x6 0x0 +#define MX50_PAD_DISP_RESET__USBPHY2_BISTOK 0x160 0x440 0x000 0x7 0x0 +#define MX50_PAD_SD3_CMD__ESDHC3_CMD 0x164 0x444 0x000 0x0 0x0 +#define MX50_PAD_SD3_CMD__GPIO5_18 0x164 0x444 0x000 0x1 0x0 +#define MX50_PAD_SD3_CMD__EIM_NANDF_WRN 0x164 0x444 0x000 0x2 0x0 +#define MX50_PAD_SD3_CMD__SSP_CMD 0x164 0x444 0x000 0x3 0x0 +#define MX50_PAD_SD3_CLK__ESDHC3_CLK 0x168 0x448 0x000 0x0 0x0 +#define MX50_PAD_SD3_CLK__GPIO5_19 0x168 0x448 0x000 0x1 0x0 +#define MX50_PAD_SD3_CLK__EIM_NANDF_RDN 0x168 0x448 0x000 0x2 0x0 +#define MX50_PAD_SD3_CLK__SSP_CLK 0x168 0x448 0x000 0x3 0x0 +#define MX50_PAD_SD3_D0__ESDHC3_DAT0 0x16c 0x44c 0x000 0x0 0x0 +#define MX50_PAD_SD3_D0__GPIO5_20 0x16c 0x44c 0x000 0x1 0x0 +#define MX50_PAD_SD3_D0__EIM_NANDF_D_4 0x16c 0x44c 0x000 0x2 0x0 +#define MX50_PAD_SD3_D0__SSP_D0 0x16c 0x44c 0x000 0x3 0x0 +#define MX50_PAD_SD3_D0__CCM_PLL1_BYP 0x16c 0x44c 0x6dc 0x7 0x1 +#define MX50_PAD_SD3_D1__ESDHC3_DAT1 0x170 0x450 0x000 0x0 0x0 +#define MX50_PAD_SD3_D1__GPIO5_21 0x170 0x450 0x000 0x1 0x0 +#define MX50_PAD_SD3_D1__EIM_NANDF_D_5 0x170 0x450 0x000 0x2 0x0 +#define MX50_PAD_SD3_D1__SSP_D1 0x170 0x450 0x000 0x3 0x0 +#define MX50_PAD_SD3_D1__CCM_PLL2_BYP 0x170 0x450 0x000 0x7 0x0 +#define MX50_PAD_SD3_D2__ESDHC3_DAT2 0x174 0x454 0x000 0x0 0x0 +#define MX50_PAD_SD3_D2__GPIO5_22 0x174 0x454 0x000 0x1 0x0 +#define MX50_PAD_SD3_D2__EIM_NANDF_D_6 0x174 0x454 0x000 0x2 0x0 +#define MX50_PAD_SD3_D2__SSP_D2 0x174 0x454 0x000 0x3 0x0 +#define MX50_PAD_SD3_D2__CCM_PLL3_BYP 0x174 0x454 0x6e4 0x7 0x1 +#define MX50_PAD_SD3_D3__ESDHC3_DAT3 0x178 0x458 0x000 0x0 0x0 +#define MX50_PAD_SD3_D3__GPIO5_23 0x178 0x458 0x000 0x1 0x0 +#define MX50_PAD_SD3_D3__EIM_NANDF_D_7 0x178 0x458 0x000 0x2 0x0 +#define MX50_PAD_SD3_D3__SSP_D3 0x178 0x458 0x000 0x3 0x0 +#define MX50_PAD_SD3_D4__ESDHC3_DAT4 0x17c 0x45c 0x000 0x0 0x0 +#define MX50_PAD_SD3_D4__GPIO5_24 0x17c 0x45c 0x000 0x1 0x0 +#define MX50_PAD_SD3_D4__EIM_NANDF_D_0 0x17c 0x45c 0x000 0x2 0x0 +#define MX50_PAD_SD3_D4__SSP_D4 0x17c 0x45c 0x000 0x3 0x0 +#define MX50_PAD_SD3_D5__ESDHC3_DAT5 0x180 0x460 0x000 0x0 0x0 +#define MX50_PAD_SD3_D5__GPIO5_25 0x180 0x460 0x000 0x1 0x0 +#define MX50_PAD_SD3_D5__EIM_NANDF_D_1 0x180 0x460 0x000 0x2 0x0 +#define MX50_PAD_SD3_D5__SSP_D5 0x180 0x460 0x000 0x3 0x0 +#define MX50_PAD_SD3_D6__ESDHC3_DAT6 0x184 0x464 0x000 0x0 0x0 +#define MX50_PAD_SD3_D6__GPIO5_26 0x184 0x464 0x000 0x1 0x0 +#define MX50_PAD_SD3_D6__EIM_NANDF_D_2 0x184 0x464 0x000 0x2 0x0 +#define MX50_PAD_SD3_D6__SSP_D6 0x184 0x464 0x000 0x3 0x0 +#define MX50_PAD_SD3_D7__ESDHC3_DAT7 0x188 0x468 0x000 0x0 0x0 +#define MX50_PAD_SD3_D7__GPIO5_27 0x188 0x468 0x000 0x1 0x0 +#define MX50_PAD_SD3_D7__EIM_NANDF_D_3 0x188 0x468 0x000 0x2 0x0 +#define MX50_PAD_SD3_D7__SSP_D7 0x188 0x468 0x000 0x3 0x0 +#define MX50_PAD_SD3_WP__ESDHC3_WP 0x18c 0x46C 0x000 0x0 0x0 +#define MX50_PAD_SD3_WP__GPIO5_28 0x18c 0x46C 0x000 0x1 0x0 +#define MX50_PAD_SD3_WP__EIM_NANDF_RESETN 0x18c 0x46C 0x000 0x2 0x0 +#define MX50_PAD_SD3_WP__SSP_CD 0x18c 0x46C 0x000 0x3 0x0 +#define MX50_PAD_SD3_WP__ESDHC4_LCTL 0x18c 0x46C 0x000 0x4 0x0 +#define MX50_PAD_SD3_WP__EIM_WEIM_CS_3 0x18c 0x46C 0x000 0x5 0x0 +#define MX50_PAD_DISP_D8__ELCDIF_DAT_8 0x190 0x470 0x71c 0x0 0x0 +#define MX50_PAD_DISP_D8__GPIO2_8 0x190 0x470 0x000 0x1 0x0 +#define MX50_PAD_DISP_D8__EIM_NANDF_CLE 0x190 0x470 0x000 0x2 0x0 +#define MX50_PAD_DISP_D8__ESDHC1_LCTL 0x190 0x470 0x000 0x3 0x0 +#define MX50_PAD_DISP_D8__ESDHC4_CMD 0x190 0x470 0x74c 0x4 0x2 +#define MX50_PAD_DISP_D8__KPP_COL_4 0x190 0x470 0x790 0x5 0x1 +#define MX50_PAD_DISP_D8__FEC_TX_CLK 0x190 0x470 0x78c 0x6 0x1 +#define MX50_PAD_DISP_D8__USBPHY1_DATAOUT_0 0x190 0x470 0x000 0x7 0x0 +#define MX50_PAD_DISP_D9__ELCDIF_DAT_9 0x194 0x474 0x720 0x0 0x0 +#define MX50_PAD_DISP_D9__GPIO2_9 0x194 0x474 0x000 0x1 0x0 +#define MX50_PAD_DISP_D9__EIM_NANDF_ALE 0x194 0x474 0x000 0x2 0x0 +#define MX50_PAD_DISP_D9__ESDHC2_LCTL 0x194 0x474 0x000 0x3 0x0 +#define MX50_PAD_DISP_D9__ESDHC4_CLK 0x194 0x474 0x748 0x4 0x2 +#define MX50_PAD_DISP_D9__KPP_ROW_4 0x194 0x474 0x7a0 0x5 0x1 +#define MX50_PAD_DISP_D9__FEC_RX_ER 0x194 0x474 0x788 0x6 0x1 +#define MX50_PAD_DISP_D9__USBPHY1_DATAOUT_1 0x194 0x474 0x000 0x7 0x0 +#define MX50_PAD_DISP_D10__ELCDIF_DAT_10 0x198 0x478 0x724 0x0 0x0 +#define MX50_PAD_DISP_D10__GPIO2_10 0x198 0x478 0x000 0x1 0x0 +#define MX50_PAD_DISP_D10__EIM_NANDF_CEN_0 0x198 0x478 0x000 0x2 0x0 +#define MX50_PAD_DISP_D10__ESDHC3_LCTL 0x198 0x478 0x000 0x3 0x0 +#define MX50_PAD_DISP_D10__ESDHC4_DAT0 0x198 0x478 0x000 0x4 0x0 +#define MX50_PAD_DISP_D10__KPP_COL_5 0x198 0x478 0x794 0x5 0x1 +#define MX50_PAD_DISP_D10__FEC_RX_DV 0x198 0x478 0x784 0x6 0x1 +#define MX50_PAD_DISP_D10__USBPHY1_DATAOUT_2 0x198 0x478 0x000 0x7 0x0 +#define MX50_PAD_DISP_D11__ELCDIF_DAT_11 0x19c 0x47c 0x728 0x0 0x0 +#define MX50_PAD_DISP_D11__GPIO2_11 0x19c 0x47c 0x000 0x1 0x0 +#define MX50_PAD_DISP_D11__EIM_NANDF_CEN_1 0x19c 0x47c 0x000 0x2 0x0 +#define MX50_PAD_DISP_D11__ESDHC4_DAT1 0x19c 0x47c 0x754 0x4 0x1 +#define MX50_PAD_DISP_D11__KPP_ROW_5 0x19c 0x47c 0x7a4 0x5 0x1 +#define MX50_PAD_DISP_D11__FEC_RDATA_1 0x19c 0x47c 0x77c 0x6 0x1 +#define MX50_PAD_DISP_D11__USBPHY1_DATAOUT_3 0x19c 0x47c 0x000 0x7 0x0 +#define MX50_PAD_DISP_D12__ELCDIF_DAT_12 0x1a0 0x480 0x72c 0x0 0x0 +#define MX50_PAD_DISP_D12__GPIO2_12 0x1a0 0x480 0x000 0x1 0x0 +#define MX50_PAD_DISP_D12__EIM_NANDF_CEN_2 0x1a0 0x480 0x000 0x2 0x0 +#define MX50_PAD_DISP_D12__ESDHC1_CD 0x1a0 0x480 0x000 0x3 0x0 +#define MX50_PAD_DISP_D12__ESDHC4_DAT2 0x1a0 0x480 0x758 0x4 0x1 +#define MX50_PAD_DISP_D12__KPP_COL_6 0x1a0 0x480 0x798 0x5 0x1 +#define MX50_PAD_DISP_D12__FEC_RDATA_0 0x1a0 0x480 0x778 0x6 0x1 +#define MX50_PAD_DISP_D12__USBPHY1_DATAOUT_4 0x1a0 0x480 0x000 0x7 0x0 +#define MX50_PAD_DISP_D13__ELCDIF_DAT_13 0x1a4 0x484 0x730 0x0 0x0 +#define MX50_PAD_DISP_D13__GPIO2_13 0x1a4 0x484 0x000 0x1 0x0 +#define MX50_PAD_DISP_D13__EIM_NANDF_CEN_3 0x1a4 0x484 0x000 0x2 0x0 +#define MX50_PAD_DISP_D13__ESDHC3_CD 0x1a4 0x484 0x000 0x3 0x0 +#define MX50_PAD_DISP_D13__ESDHC4_DAT3 0x1a4 0x484 0x75c 0x4 0x1 +#define MX50_PAD_DISP_D13__KPP_ROW_6 0x1a4 0x484 0x7a8 0x5 0x1 +#define MX50_PAD_DISP_D13__FEC_TX_EN 0x1a4 0x484 0x000 0x6 0x0 +#define MX50_PAD_DISP_D13__USBPHY1_DATAOUT_5 0x1a4 0x484 0x000 0x7 0x0 +#define MX50_PAD_DISP_D14__ELCDIF_DAT_14 0x1a8 0x488 0x734 0x0 0x0 +#define MX50_PAD_DISP_D14__GPIO2_14 0x1a8 0x488 0x000 0x1 0x0 +#define MX50_PAD_DISP_D14__EIM_NANDF_READY0 0x1a8 0x488 0x7b4 0x2 0x1 +#define MX50_PAD_DISP_D14__ESDHC1_WP 0x1a8 0x488 0x000 0x3 0x0 +#define MX50_PAD_DISP_D14__ESDHC4_WP 0x1a8 0x488 0x000 0x4 0x0 +#define MX50_PAD_DISP_D14__KPP_COL_7 0x1a8 0x488 0x79c 0x5 0x1 +#define MX50_PAD_DISP_D14__FEC_TDATA_1 0x1a8 0x488 0x000 0x6 0x0 +#define MX50_PAD_DISP_D14__USBPHY1_DATAOUT_6 0x1a8 0x488 0x000 0x7 0x0 +#define MX50_PAD_DISP_D15__ELCDIF_DAT_15 0x1ac 0x48c 0x738 0x0 0x0 +#define MX50_PAD_DISP_D15__GPIO2_15 0x1ac 0x48c 0x000 0x1 0x0 +#define MX50_PAD_DISP_D15__EIM_NANDF_DQS 0x1ac 0x48c 0x7b0 0x2 0x1 +#define MX50_PAD_DISP_D15__ESDHC3_RST 0x1ac 0x48c 0x000 0x3 0x0 +#define MX50_PAD_DISP_D15__ESDHC4_CD 0x1ac 0x48c 0x000 0x4 0x0 +#define MX50_PAD_DISP_D15__KPP_ROW_7 0x1ac 0x48c 0x7ac 0x5 0x1 +#define MX50_PAD_DISP_D15__FEC_TDATA_0 0x1ac 0x48c 0x000 0x6 0x0 +#define MX50_PAD_DISP_D15__USBPHY1_DATAOUT_7 0x1ac 0x48c 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D0__EPDC_SDDO_0 0x1b0 0x54c 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D0__GPIO3_0 0x1b0 0x54c 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D0__EIM_WEIM_D_0 0x1b0 0x54c 0x7ec 0x2 0x1 +#define MX50_PAD_EPDC_D0__ELCDIF_RS 0x1b0 0x54c 0x000 0x3 0x0 +#define MX50_PAD_EPDC_D0__ELCDIF_DOTCLK 0x1b0 0x54c 0x000 0x4 0x0 +#define MX50_PAD_EPDC_D0__SDMA_DEBUG_EVT_CHN_LINES_0 0x1b0 0x54c 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D0__USBPHY2_DATAOUT_0 0x1b0 0x54c 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D1__EPDC_SDDO_1 0x1b4 0x550 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D1__GPIO3_1 0x1b4 0x550 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D1__EIM_WEIM_D_1 0x1b4 0x550 0x7f0 0x2 0x1 +#define MX50_PAD_EPDC_D1__ELCDIF_CS 0x1b4 0x550 0x000 0x3 0x0 +#define MX50_PAD_EPDC_D1__ELCDIF_ENABLE 0x1b4 0x550 0x000 0x4 0x0 +#define MX50_PAD_EPDC_D1__SDMA_DEBUG_EVT_CHN_LINES_1 0x1b4 0x550 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D1__USBPHY2_DATAOUT_1 0x1b4 0x550 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D2__EPDC_SDDO_2 0x1b8 0x554 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D2__GPIO3_2 0x1b8 0x554 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D2__EIM_WEIM_D_2 0x1b8 0x554 0x7f4 0x2 0x1 +#define MX50_PAD_EPDC_D2__ELCDIF_WR_RWN 0x1b8 0x554 0x000 0x3 0x0 +#define MX50_PAD_EPDC_D2__ELCDIF_VSYNC 0x1b8 0x554 0x73c 0x4 0x2 +#define MX50_PAD_EPDC_D2__SDMA_DEBUG_EVT_CHN_LINES_2 0x1b8 0x554 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D2__USBPHY2_DATAOUT_2 0x1b8 0x554 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D3__EPDC_SDDO_3 0x1bc 0x558 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D3__GPIO3_3 0x1bc 0x558 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D3__EIM_WEIM_D_3 0x1bc 0x558 0x7f8 0x2 0x1 +#define MX50_PAD_EPDC_D3__ELCDIF_RD_E 0x1bc 0x558 0x000 0x3 0x0 +#define MX50_PAD_EPDC_D3__ELCDIF_HSYNC 0x1bc 0x558 0x6f8 0x4 0x3 +#define MX50_PAD_EPDC_D3__SDMA_DEBUG_EVT_CHN_LINES_3 0x1bc 0x558 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D3__USBPHY2_DATAOUT_3 0x1bc 0x558 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D4__EPDC_SDDO_4 0x1c0 0x55c 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D4__GPIO3_4 0x1c0 0x55c 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D4__EIM_WEIM_D_4 0x1c0 0x55c 0x7fc 0x2 0x1 +#define MX50_PAD_EPDC_D4__SDMA_DEBUG_EVT_CHN_LINES_4 0x1c0 0x55c 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D4__USBPHY2_DATAOUT_4 0x1c0 0x55c 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D5__EPDC_SDDO_5 0x1c4 0x560 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D5__GPIO3_5 0x1c4 0x560 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D5__EIM_WEIM_D_5 0x1c4 0x560 0x800 0x2 0x1 +#define MX50_PAD_EPDC_D5__SDMA_DEBUG_EVT_CHN_LINES_5 0x1c4 0x560 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D5__USBPHY2_DATAOUT_5 0x1c4 0x560 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D6__EPDC_SDDO_6 0x1c8 0x564 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D6__GPIO3_6 0x1c8 0x564 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D6__EIM_WEIM_D_6 0x1c8 0x564 0x804 0x2 0x1 +#define MX50_PAD_EPDC_D6__SDMA_DEBUG_EVT_CHN_LINES_6 0x1c8 0x564 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D6__USBPHY2_DATAOUT_6 0x1c8 0x564 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D7__EPDC_SDDO_7 0x1cc 0x568 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D7__GPIO3_7 0x1cc 0x568 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D7__EIM_WEIM_D_7 0x1cc 0x568 0x808 0x2 0x1 +#define MX50_PAD_EPDC_D7__SDMA_DEBUG_EVT_CHN_LINES_7 0x1cc 0x568 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D7__USBPHY2_DATAOUT_7 0x1cc 0x568 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D8__EPDC_SDDO_8 0x1d0 0x56c 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D8__GPIO3_8 0x1d0 0x56c 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D8__EIM_WEIM_D_8 0x1d0 0x56c 0x80c 0x2 0x2 +#define MX50_PAD_EPDC_D8__ELCDIF_DAT_24 0x1d0 0x56c 0x000 0x3 0x0 +#define MX50_PAD_EPDC_D8__SDMA_DEBUG_MATCHED_DMBUS 0x1d0 0x56c 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D8__USBPHY2_VSTATUS_0 0x1d0 0x56c 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D9__EPDC_SDDO_9 0x1d4 0x570 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D9__GPIO3_9 0x1d4 0x570 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D9__EIM_WEIM_D_9 0x1d4 0x570 0x810 0x2 0x2 +#define MX50_PAD_EPDC_D9__ELCDIF_DAT_25 0x1d4 0x570 0x000 0x3 0x0 +#define MX50_PAD_EPDC_D9__SDMA_DEBUG_EVENT_CHANNEL_SEL 0x1d4 0x570 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D9__USBPHY2_VSTATUS_1 0x1d4 0x570 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D10__EPDC_SDDO_10 0x1d8 0x574 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D10__GPIO3_10 0x1d8 0x574 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D10__EIM_WEIM_D_10 0x1d8 0x574 0x814 0x2 0x2 +#define MX50_PAD_EPDC_D10__ELCDIF_DAT_26 0x1d8 0x574 0x000 0x3 0x0 +#define MX50_PAD_EPDC_D10__SDMA_DEBUG_EVENT_CHANNEL_0 0x1d8 0x574 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D10__USBPHY2_VSTATUS_2 0x1d8 0x574 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D11__EPDC_SDDO_11 0x1dc 0x578 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D11__GPIO3_11 0x1dc 0x578 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D11__EIM_WEIM_D_11 0x1dc 0x578 0x818 0x2 0x2 +#define MX50_PAD_EPDC_D11__ELCDIF_DAT_27 0x1dc 0x578 0x000 0x3 0x0 +#define MX50_PAD_EPDC_D11__SDMA_DEBUG_EVENT_CHANNEL_1 0x1dc 0x578 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D11__USBPHY2_VSTATUS_3 0x1dc 0x578 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D12__EPDC_SDDO_12 0x1e0 0x57c 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D12__GPIO3_12 0x1e0 0x57c 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D12__EIM_WEIM_D_12 0x1e0 0x57c 0x81c 0x2 0x1 +#define MX50_PAD_EPDC_D12__ELCDIF_DAT_28 0x1e0 0x57c 0x000 0x3 0x0 +#define MX50_PAD_EPDC_D12__SDMA_DEBUG_EVENT_CHANNEL_2 0x1e0 0x57c 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D12__USBPHY2_VSTATUS_4 0x1e0 0x57c 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D13__EPDC_SDDO_13 0x1e4 0x580 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D13__GPIO3_13 0x1e4 0x580 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D13__EIM_WEIM_D_13 0x1e4 0x580 0x820 0x2 0x1 +#define MX50_PAD_EPDC_D13__ELCDIF_DAT_29 0x1e4 0x580 0x000 0x3 0x0 +#define MX50_PAD_EPDC_D13__SDMA_DEBUG_EVENT_CHANNEL_3 0x1e4 0x580 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D13__USBPHY2_VSTATUS_5 0x1e4 0x580 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D14__EPDC_SDDO_14 0x1e8 0x584 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D14__GPIO3_14 0x1e8 0x584 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D14__EIM_WEIM_D_14 0x1e8 0x584 0x824 0x2 0x1 +#define MX50_PAD_EPDC_D14__ELCDIF_DAT_30 0x1e8 0x584 0x000 0x3 0x0 +#define MX50_PAD_EPDC_D14__AUDMUX_AUD6_TXD 0x1e8 0x584 0x000 0x4 0x0 +#define MX50_PAD_EPDC_D14__SDMA_DEBUG_EVENT_CHANNEL_4 0x1e8 0x584 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D14__USBPHY2_VSTATUS_6 0x1e8 0x584 0x000 0x7 0x0 +#define MX50_PAD_EPDC_D15__EPDC_SDDO_15 0x1ec 0x588 0x000 0x0 0x0 +#define MX50_PAD_EPDC_D15__GPIO3_15 0x1ec 0x588 0x000 0x1 0x0 +#define MX50_PAD_EPDC_D15__EIM_WEIM_D_15 0x1ec 0x588 0x828 0x2 0x1 +#define MX50_PAD_EPDC_D15__ELCDIF_DAT_31 0x1ec 0x588 0x000 0x3 0x0 +#define MX50_PAD_EPDC_D15__AUDMUX_AUD6_TXC 0x1ec 0x588 0x000 0x4 0x0 +#define MX50_PAD_EPDC_D15__SDMA_DEBUG_EVENT_CHANNEL_5 0x1ec 0x588 0x000 0x6 0x0 +#define MX50_PAD_EPDC_D15__USBPHY2_VSTATUS_7 0x1ec 0x588 0x000 0x7 0x0 +#define MX50_PAD_EPDC_GDCLK__EPDC_GDCLK 0x1f0 0x58c 0x000 0x0 0x0 +#define MX50_PAD_EPDC_GDCLK__GPIO3_16 0x1f0 0x58c 0x000 0x1 0x0 +#define MX50_PAD_EPDC_GDCLK__EIM_WEIM_D_16 0x1f0 0x58c 0x000 0x2 0x0 +#define MX50_PAD_EPDC_GDCLK__ELCDIF_DAT_16 0x1f0 0x58c 0x000 0x3 0x0 +#define MX50_PAD_EPDC_GDCLK__AUDMUX_AUD6_TXFS 0x1f0 0x58c 0x000 0x4 0x0 +#define MX50_PAD_EPDC_GDCLK__SDMA_DEBUG_CORE_STATE_0 0x1f0 0x58c 0x000 0x6 0x0 +#define MX50_PAD_EPDC_GDCLK__USBPHY2_BISTOK 0x1f0 0x58c 0x000 0x7 0x0 +#define MX50_PAD_EPDC_GDSP__EPCD_GDSP 0x1f4 0x590 0x000 0x0 0x0 +#define MX50_PAD_EPDC_GDSP__GPIO3_17 0x1f4 0x590 0x000 0x1 0x0 +#define MX50_PAD_EPDC_GDSP__EIM_WEIM_D_17 0x1f4 0x590 0x000 0x2 0x0 +#define MX50_PAD_EPDC_GDSP__ELCDIF_DAT_17 0x1f4 0x590 0x000 0x3 0x0 +#define MX50_PAD_EPDC_GDSP__AUDMUX_AUD6_RXD 0x1f4 0x590 0x000 0x4 0x0 +#define MX50_PAD_EPDC_GDSP__SDMA_DEBUG_CORE_STATE_1 0x1f4 0x590 0x000 0x6 0x0 +#define MX50_PAD_EPDC_GDSP__USBPHY2_BVALID 0x1f4 0x590 0x000 0x7 0x0 +#define MX50_PAD_EPDC_GDOE__EPCD_GDOE 0x1f8 0x594 0x000 0x0 0x0 +#define MX50_PAD_EPDC_GDOE__GPIO3_18 0x1f8 0x594 0x000 0x1 0x0 +#define MX50_PAD_EPDC_GDOE__EIM_WEIM_D_18 0x1f8 0x594 0x000 0x2 0x0 +#define MX50_PAD_EPDC_GDOE__ELCDIF_DAT_18 0x1f8 0x594 0x000 0x3 0x0 +#define MX50_PAD_EPDC_GDOE__AUDMUX_AUD6_RXC 0x1f8 0x594 0x000 0x4 0x0 +#define MX50_PAD_EPDC_GDOE__SDMA_DEBUG_CORE_STATE_2 0x1f8 0x594 0x000 0x6 0x0 +#define MX50_PAD_EPDC_GDOE__USBPHY2_ENDSESSION 0x1f8 0x594 0x000 0x7 0x0 +#define MX50_PAD_EPDC_GDRL__EPCD_GDRL 0x1fc 0x598 0x000 0x0 0x0 +#define MX50_PAD_EPDC_GDRL__GPIO3_19 0x1fc 0x598 0x000 0x1 0x0 +#define MX50_PAD_EPDC_GDRL__EIM_WEIM_D_19 0x1f8 0x598 0x000 0x2 0x0 +#define MX50_PAD_EPDC_GDRL__ELCDIF_DAT_19 0x1fc 0x598 0x000 0x3 0x0 +#define MX50_PAD_EPDC_GDRL__AUDMUX_AUD6_RXFS 0x1fc 0x598 0x000 0x4 0x0 +#define MX50_PAD_EPDC_GDRL__SDMA_DEBUG_CORE_STATE_3 0x1fc 0x598 0x000 0x6 0x0 +#define MX50_PAD_EPDC_GDRL__USBPHY2_IDDIG 0x1fc 0x598 0x000 0x7 0x0 +#define MX50_PAD_EPDC_SDCLK__EPCD_SDCLK 0x200 0x59c 0x000 0x0 0x0 +#define MX50_PAD_EPDC_SDCLK__GPIO3_20 0x200 0x59c 0x000 0x1 0x0 +#define MX50_PAD_EPDC_SDCLK__EIM_WEIM_D_20 0x200 0x59c 0x000 0x2 0x0 +#define MX50_PAD_EPDC_SDCLK__ELCDIF_DAT_20 0x200 0x59c 0x000 0x3 0x0 +#define MX50_PAD_EPDC_SDCLK__AUDMUX_AUD5_TXD 0x200 0x59c 0x000 0x4 0x0 +#define MX50_PAD_EPDC_SDCLK__SDMA_DEBUG_BUS_DEVICE_0 0x200 0x59c 0x000 0x6 0x0 +#define MX50_PAD_EPDC_SDCLK__USBPHY2_HOSTDISCONNECT 0x200 0x59c 0x000 0x7 0x0 +#define MX50_PAD_EPDC_SDOEZ__EPCD_SDOEZ 0x204 0x5a0 0x000 0x0 0x0 +#define MX50_PAD_EPDC_SDOEZ__GPIO3_21 0x204 0x5a0 0x000 0x1 0x0 +#define MX50_PAD_EPDC_SDOEZ__EIM_WEIM_D_21 0x204 0x5a0 0x000 0x2 0x0 +#define MX50_PAD_EPDC_SDOEZ__ELCDIF_DAT_21 0x204 0x5a0 0x000 0x3 0x0 +#define MX50_PAD_EPDC_SDOEZ__AUDMUX_AUD5_TXC 0x204 0x5a0 0x000 0x4 0x0 +#define MX50_PAD_EPDC_SDOEZ__SDMA_DEBUG_BUS_DEVICE_1 0x204 0x5a0 0x000 0x6 0x0 +#define MX50_PAD_EPDC_SDOEZ__USBPHY2_TXREADY 0x204 0x5a0 0x000 0x7 0x0 +#define MX50_PAD_EPDC_SDOED__EPCD_SDOED 0x208 0x5a4 0x000 0x0 0x0 +#define MX50_PAD_EPDC_SDOED__GPIO3_22 0x208 0x5a4 0x000 0x1 0x0 +#define MX50_PAD_EPDC_SDOED__EIM_WEIM_D_22 0x208 0x5a4 0x000 0x2 0x0 +#define MX50_PAD_EPDC_SDOED__ELCDIF_DAT_22 0x208 0x5a4 0x000 0x3 0x0 +#define MX50_PAD_EPDC_SDOED__AUDMUX_AUD5_TXFS 0x208 0x5a4 0x000 0x4 0x0 +#define MX50_PAD_EPDC_SDOED__SDMA_DEBUG_BUS_DEVICE_2 0x208 0x5a4 0x000 0x6 0x0 +#define MX50_PAD_EPDC_SDOED__USBPHY2_RXVALID 0x208 0x5a4 0x000 0x7 0x0 +#define MX50_PAD_EPDC_SDOE__EPCD_SDOE 0x20c 0x5a8 0x000 0x0 0x0 +#define MX50_PAD_EPDC_SDOE__GPIO3_23 0x20c 0x5a8 0x000 0x1 0x0 +#define MX50_PAD_EPDC_SDOE__EIM_WEIM_D_23 0x20c 0x5a8 0x000 0x2 0x0 +#define MX50_PAD_EPDC_SDOE__ELCDIF_DAT_23 0x20c 0x5a8 0x000 0x3 0x0 +#define MX50_PAD_EPDC_SDOE__AUDMUX_AUD5_RXD 0x20c 0x5a8 0x000 0x4 0x0 +#define MX50_PAD_EPDC_SDOE__SDMA_DEBUG_BUS_DEVICE_3 0x20c 0x5a8 0x000 0x6 0x0 +#define MX50_PAD_EPDC_SDOE__USBPHY2_RXACTIVE 0x20c 0x5a8 0x000 0x7 0x0 +#define MX50_PAD_EPDC_SDLE__EPCD_SDLE 0x210 0x5ac 0x000 0x0 0x0 +#define MX50_PAD_EPDC_SDLE__GPIO3_24 0x210 0x5ac 0x000 0x1 0x0 +#define MX50_PAD_EPDC_SDLE__EIM_WEIM_D_24 0x210 0x5ac 0x000 0x2 0x0 +#define MX50_PAD_EPDC_SDLE__ELCDIF_DAT_8 0x210 0x5ac 0x71c 0x3 0x1 +#define MX50_PAD_EPDC_SDLE__AUDMUX_AUD5_RXC 0x210 0x5ac 0x000 0x4 0x0 +#define MX50_PAD_EPDC_SDLE__SDMA_DEBUG_BUS_DEVICE_4 0x210 0x5ac 0x000 0x6 0x0 +#define MX50_PAD_EPDC_SDLE__USBPHY2_RXERROR 0x210 0x5ac 0x000 0x7 0x0 +#define MX50_PAD_EPDC_SDCLKN__EPCD_SDCLKN 0x214 0x5b0 0x000 0x0 0x0 +#define MX50_PAD_EPDC_SDCLKN__GPIO3_25 0x214 0x5b0 0x000 0x1 0x0 +#define MX50_PAD_EPDC_SDCLKN__EIM_WEIM_D_25 0x214 0x5b0 0x000 0x2 0x0 +#define MX50_PAD_EPDC_SDCLKN__ELCDIF_DAT_9 0x214 0x5b0 0x720 0x3 0x1 +#define MX50_PAD_EPDC_SDCLKN__AUDMUX_AUD5_RXFS 0x214 0x5b0 0x000 0x4 0x0 +#define MX50_PAD_EPDC_SDCLKN__SDMA_DEBUG_BUS_ERROR 0x214 0x5b0 0x000 0x6 0x0 +#define MX50_PAD_EPDC_SDCLKN__USBPHY2_SIECLOCK 0x214 0x5b0 0x000 0x7 0x0 +#define MX50_PAD_EPDC_SDSHR__EPCD_SDSHR 0x218 0x5b4 0x000 0x0 0x0 +#define MX50_PAD_EPDC_SDSHR__GPIO3_26 0x218 0x5b4 0x000 0x1 0x0 +#define MX50_PAD_EPDC_SDSHR__EIM_WEIM_D_26 0x218 0x5b4 0x000 0x2 0x0 +#define MX50_PAD_EPDC_SDSHR__ELCDIF_DAT_10 0x218 0x5b4 0x724 0x3 0x1 +#define MX50_PAD_EPDC_SDSHR__AUDMUX_AUD4_TXD 0x218 0x5b4 0x6c8 0x4 0x1 +#define MX50_PAD_EPDC_SDSHR__SDMA_DEBUG_BUS_RWB 0x218 0x5b4 0x000 0x6 0x0 +#define MX50_PAD_EPDC_SDSHR__USBPHY2_LINESTATE_0 0x218 0x5b4 0x000 0x7 0x0 +#define MX50_PAD_EPDC_PWRCOM__EPCD_PWRCOM 0x21c 0x5b8 0x000 0x0 0x0 +#define MX50_PAD_EPDC_PWRCOM__GPIO3_27 0x21c 0x5b8 0x000 0x1 0x0 +#define MX50_PAD_EPDC_PWRCOM__EIM_WEIM_D_27 0x21c 0x5b8 0x000 0x2 0x0 +#define MX50_PAD_EPDC_PWRCOM__ELCDIF_DAT_11 0x21c 0x5b8 0x728 0x3 0x1 +#define MX50_PAD_EPDC_PWRCOM__AUDMUX_AUD4_TXC 0x21c 0x5b8 0x6d4 0x4 0x1 +#define MX50_PAD_EPDC_PWRCOM__SDMA_DEBUG_CORE_RUN 0x21c 0x5b8 0x000 0x6 0x0 +#define MX50_PAD_EPDC_PWRCOM__USBPHY2_LINESTATE_1 0x21c 0x5b8 0x000 0x7 0x0 +#define MX50_PAD_EPDC_PWRSTAT__EPCD_PWRSTAT 0x220 0x5bc 0x000 0x0 0x0 +#define MX50_PAD_EPDC_PWRSTAT__GPIO3_28 0x220 0x5bc 0x000 0x1 0x0 +#define MX50_PAD_EPDC_PWRSTAT__EIM_WEIM_D_28 0x220 0x5bc 0x000 0x2 0x0 +#define MX50_PAD_EPDC_PWRSTAT__ELCDIF_DAT_12 0x220 0x5bc 0x72c 0x3 0x1 +#define MX50_PAD_EPDC_PWRSTAT__AUDMUX_AUD4_TXFS 0x220 0x5bc 0x6d8 0x4 0x1 +#define MX50_PAD_EPDC_PWRSTAT__SDMA_DEBUG_MODE 0x220 0x5bc 0x000 0x6 0x0 +#define MX50_PAD_EPDC_PWRSTAT__USBPHY2_VBUSVALID 0x220 0x5bc 0x000 0x7 0x0 +#define MX50_PAD_EPDC_PWRCTRL0__EPCD_PWRCTRL0 0x224 0x5c0 0x000 0x0 0x0 +#define MX50_PAD_EPDC_PWRCTRL0__GPIO3_29 0x224 0x5c0 0x000 0x1 0x0 +#define MX50_PAD_EPDC_PWRCTRL0__EIM_WEIM_D_29 0x224 0x5c0 0x000 0x2 0x0 +#define MX50_PAD_EPDC_PWRCTRL0__ELCDIF_DAT_13 0x224 0x5c0 0x730 0x3 0x1 +#define MX50_PAD_EPDC_PWRCTRL0__AUDMUX_AUD4_RXD 0x224 0x5c0 0x6c4 0x4 0x1 +#define MX50_PAD_EPDC_PWRCTRL0__SDMA_DEBUG_RTBUFFER_WRITE 0x224 0x5c0 0x000 0x6 0x0 +#define MX50_PAD_EPDC_PWRCTRL0__USBPHY2_AVALID 0x224 0x5c0 0x000 0x7 0x0 +#define MX50_PAD_EPDC_PWRCTRL1__EPCD_PWRCTRL1 0x228 0x5c4 0x000 0x0 0x0 +#define MX50_PAD_EPDC_PWRCTRL1__GPIO3_30 0x228 0x5c4 0x000 0x1 0x0 +#define MX50_PAD_EPDC_PWRCTRL1__EIM_WEIM_D_30 0x228 0x5c4 0x000 0x2 0x0 +#define MX50_PAD_EPDC_PWRCTRL1__ELCDIF_DAT_14 0x228 0x5c4 0x734 0x3 0x1 +#define MX50_PAD_EPDC_PWRCTRL1__AUDMUX_AUD4_RXC 0x228 0x5c4 0x6cc 0x4 0x1 +#define MX50_PAD_EPDC_PWRCTRL1__SDMA_DEBUG_YIELD 0x228 0x5c4 0x000 0x6 0x0 +#define MX50_PAD_EPDC_PWRCTRL1__USBPHY1_ONBIST 0x228 0x5c4 0x000 0x7 0x0 +#define MX50_PAD_EPDC_PWRCTRL2__EPCD_PWRCTRL2 0x22c 0x5c8 0x000 0x0 0x0 +#define MX50_PAD_EPDC_PWRCTRL2__GPIO3_31 0x22c 0x5c8 0x000 0x1 0x0 +#define MX50_PAD_EPDC_PWRCTRL2__EIM_WEIM_D_31 0x22c 0x5c8 0x000 0x2 0x0 +#define MX50_PAD_EPDC_PWRCTRL2__ELCDIF_DAT_15 0x22c 0x5c8 0x738 0x3 0x1 +#define MX50_PAD_EPDC_PWRCTRL2__AUDMUX_AUD4_RXFS 0x22c 0x5c8 0x6d0 0x4 0x1 +#define MX50_PAD_EPDC_PWRCTRL2__SDMA_EXT_EVENT_0 0x22c 0x5c8 0x7b8 0x6 0x1 +#define MX50_PAD_EPDC_PWRCTRL2__USBPHY2_ONBIST 0x22c 0x5c8 0x000 0x7 0x0 +#define MX50_PAD_EPDC_PWRCTRL3__EPCD_PWRCTRL3 0x230 0x5cc 0x000 0x0 0x0 +#define MX50_PAD_EPDC_PWRCTRL3__GPIO4_20 0x230 0x5cc 0x000 0x1 0x0 +#define MX50_PAD_EPDC_PWRCTRL3__EIM_WEIM_EB_2 0x230 0x5cc 0x000 0x2 0x0 +#define MX50_PAD_EPDC_PWRCTRL3__SDMA_EXT_EVENT_1 0x230 0x5cc 0x7bc 0x6 0x1 +#define MX50_PAD_EPDC_PWRCTRL3__USBPHY1_BISTOK 0x230 0x5cc 0x000 0x7 0x0 +#define MX50_PAD_EPDC_VCOM0__EPCD_VCOM_0 0x234 0x5d0 0x000 0x0 0x0 +#define MX50_PAD_EPDC_VCOM0__GPIO4_21 0x234 0x5d0 0x000 0x1 0x0 +#define MX50_PAD_EPDC_VCOM0__EIM_WEIM_EB_3 0x234 0x5d0 0x000 0x2 0x0 +#define MX50_PAD_EPDC_VCOM0__USBPHY2_BISTOK 0x234 0x5d0 0x000 0x7 0x0 +#define MX50_PAD_EPDC_VCOM1__EPCD_VCOM_1 0x238 0x5d4 0x000 0x0 0x0 +#define MX50_PAD_EPDC_VCOM1__GPIO4_22 0x238 0x5d4 0x000 0x1 0x0 +#define MX50_PAD_EPDC_VCOM1__EIM_WEIM_CS_3 0x238 0x5d4 0x000 0x2 0x0 +#define MX50_PAD_EPDC_BDR0__EPCD_BDR_0 0x23c 0x5d8 0x000 0x0 0x0 +#define MX50_PAD_EPDC_BDR0__GPIO4_23 0x23c 0x5d8 0x000 0x1 0x0 +#define MX50_PAD_EPDC_BDR0__ELCDIF_DAT_7 0x23c 0x5d8 0x718 0x3 0x1 +#define MX50_PAD_EPDC_BDR1__EPCD_BDR_1 0x240 0x5dc 0x000 0x0 0x0 +#define MX50_PAD_EPDC_BDR1__GPIO4_24 0x240 0x5dc 0x000 0x1 0x0 +#define MX50_PAD_EPDC_BDR1__ELCDIF_DAT_6 0x240 0x5dc 0x714 0x3 0x1 +#define MX50_PAD_EPDC_SDCE0__EPCD_SDCE_0 0x244 0x5e0 0x000 0x0 0x0 +#define MX50_PAD_EPDC_SDCE0__GPIO4_25 0x244 0x5e0 0x000 0x1 0x0 +#define MX50_PAD_EPDC_SDCE0__ELCDIF_DAT_5 0x244 0x5e0 0x710 0x3 0x1 +#define MX50_PAD_EPDC_SDCE1__EPCD_SDCE_1 0x248 0x5e4 0x000 0x0 0x0 +#define MX50_PAD_EPDC_SDCE1__GPIO4_26 0x248 0x5e4 0x000 0x1 0x0 +#define MX50_PAD_EPDC_SDCE1__ELCDIF_DAT_4 0x248 0x5e4 0x70c 0x3 0x0 +#define MX50_PAD_EPDC_SDCE2__EPCD_SDCE_2 0x24c 0x5e8 0x000 0x0 0x0 +#define MX50_PAD_EPDC_SDCE2__GPIO4_27 0x24c 0x5e8 0x000 0x1 0x0 +#define MX50_PAD_EPDC_SDCE2__ELCDIF_DAT_3 0x24c 0x5e8 0x708 0x3 0x1 +#define MX50_PAD_EPDC_SDCE3__EPCD_SDCE_3 0x250 0x5ec 0x000 0x0 0x0 +#define MX50_PAD_EPDC_SDCE3__GPIO4_28 0x250 0x5ec 0x000 0x1 0x0 +#define MX50_PAD_EPDC_SDCE3__ELCDIF_DAT_2 0x250 0x5ec 0x704 0x3 0x1 +#define MX50_PAD_EPDC_SDCE4__EPCD_SDCE_4 0x254 0x5f0 0x000 0x0 0x0 +#define MX50_PAD_EPDC_SDCE4__GPIO4_29 0x254 0x5f0 0x000 0x1 0x0 +#define MX50_PAD_EPDC_SDCE4__ELCDIF_DAT_1 0x254 0x5f0 0x700 0x3 0x1 +#define MX50_PAD_EPDC_SDCE5__EPCD_SDCE_5 0x258 0x5f4 0x000 0x0 0x0 +#define MX50_PAD_EPDC_SDCE5__GPIO4_30 0x258 0x5f4 0x000 0x1 0x0 +#define MX50_PAD_EPDC_SDCE5__ELCDIF_DAT_0 0x258 0x5f4 0x6fc 0x3 0x1 +#define MX50_PAD_EIM_DA0__EIM_WEIM_A_0 0x25c 0x5f8 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA0__GPIO1_0 0x25c 0x5f8 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA0__KPP_COL_4 0x25c 0x5f8 0x790 0x3 0x2 +#define MX50_PAD_EIM_DA0__TPIU_TRACE_0 0x25c 0x5f8 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA0__SRC_BT_CFG1_0 0x25c 0x5f8 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA1__EIM_WEIM_A_1 0x260 0x5fc 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA1__GPIO1_1 0x260 0x5fc 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA1__KPP_ROW_4 0x260 0x5fc 0x7a0 0x3 0x2 +#define MX50_PAD_EIM_DA1__TPIU_TRACE_1 0x260 0x5fc 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA1__SRC_BT_CFG1_1 0x260 0x5fc 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA2__EIM_WEIM_A_2 0x264 0x600 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA2__GPIO1_2 0x264 0x600 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA2__KPP_COL_5 0x264 0x600 0x794 0x3 0x2 +#define MX50_PAD_EIM_DA2__TPIU_TRACE_2 0x264 0x600 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA2__SRC_BT_CFG1_2 0x264 0x600 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA3__EIM_WEIM_A_3 0x268 0x604 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA3__GPIO1_3 0x268 0x604 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA3__KPP_ROW_5 0x268 0x604 0x7a4 0x3 0x2 +#define MX50_PAD_EIM_DA3__TPIU_TRACE_3 0x268 0x604 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA3__SRC_BT_CFG1_3 0x268 0x604 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA4__EIM_WEIM_A_4 0x26c 0x608 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA4__GPIO1_4 0x26c 0x608 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA4__KPP_COL_6 0x26c 0x608 0x798 0x3 0x2 +#define MX50_PAD_EIM_DA4__TPIU_TRACE_4 0x26c 0x608 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA4__SRC_BT_CFG1_4 0x26c 0x608 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA5__EIM_WEIM_A_5 0x270 0x60c 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA5__GPIO1_5 0x270 0x60c 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA5__KPP_ROW_6 0x270 0x60c 0x7a8 0x3 0x2 +#define MX50_PAD_EIM_DA5__TPIU_TRACE_5 0x270 0x60c 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA5__SRC_BT_CFG1_5 0x270 0x60c 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA6__EIM_WEIM_A_6 0x274 0x610 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA6__GPIO1_6 0x274 0x610 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA6__KPP_COL_7 0x274 0x610 0x79c 0x3 0x2 +#define MX50_PAD_EIM_DA6__TPIU_TRACE_6 0x274 0x610 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA6__SRC_BT_CFG1_6 0x274 0x610 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA7__EIM_WEIM_A_7 0x278 0x614 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA7__GPIO1_7 0x278 0x614 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA7__KPP_ROW_7 0x278 0x614 0x7ac 0x3 0x2 +#define MX50_PAD_EIM_DA7__TPIU_TRACE_7 0x278 0x614 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA7__SRC_BT_CFG1_7 0x278 0x614 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA8__EIM_WEIM_A_8 0x27c 0x618 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA8__GPIO1_8 0x27c 0x618 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA8__EIM_NANDF_CLE 0x27c 0x618 0x000 0x2 0x0 +#define MX50_PAD_EIM_DA8__TPIU_TRACE_8 0x27c 0x618 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA8__SRC_BT_CFG2_0 0x27c 0x618 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA9__EIM_WEIM_A_9 0x280 0x61c 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA9__GPIO1_9 0x280 0x61c 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA9__EIM_NANDF_ALE 0x280 0x61c 0x000 0x2 0x0 +#define MX50_PAD_EIM_DA9__TPIU_TRACE_9 0x280 0x61c 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA9__SRC_BT_CFG2_1 0x280 0x61c 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA10__EIM_WEIM_A_10 0x284 0x620 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA10__GPIO1_10 0x284 0x620 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA10__EIM_NANDF_CEN_0 0x284 0x620 0x000 0x2 0x0 +#define MX50_PAD_EIM_DA10__TPIU_TRACE_10 0x284 0x620 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA10__SRC_BT_CFG2_2 0x284 0x620 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA11__EIM_WEIM_A_11 0x288 0x624 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA11__GPIO1_11 0x288 0x624 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA11__EIM_NANDF_CEN_1 0x288 0x624 0x000 0x2 0x0 +#define MX50_PAD_EIM_DA11__TPIU_TRACE_11 0x288 0x624 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA11__SRC_BT_CFG2_3 0x288 0x624 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA12__EIM_WEIM_A_12 0x28c 0x628 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA12__GPIO1_12 0x28c 0x628 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA12__EIM_NANDF_CEN_2 0x28c 0x628 0x000 0x2 0x0 +#define MX50_PAD_EIM_DA12__EPDC_SDCE_6 0x28c 0x628 0x000 0x3 0x0 +#define MX50_PAD_EIM_DA12__TPIU_TRACE_12 0x28c 0x628 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA12__SRC_BT_CFG2_4 0x28c 0x628 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA13__EIM_WEIM_A_13 0x290 0x62c 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA13__GPIO1_13 0x290 0x62c 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA13__EIM_NANDF_CEN_3 0x290 0x62c 0x000 0x2 0x0 +#define MX50_PAD_EIM_DA13__EPDC_SDCE_7 0x290 0x62c 0x000 0x3 0x0 +#define MX50_PAD_EIM_DA13__TPIU_TRACE_13 0x290 0x62c 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA13__SRC_BT_CFG2_5 0x290 0x62c 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA14__EIM_WEIM_A_14 0x294 0x630 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA14__GPIO1_14 0x294 0x630 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA14__EIM_NANDF_READY0 0x294 0x630 0x7b4 0x2 0x2 +#define MX50_PAD_EIM_DA14__EPDC_SDCE_8 0x294 0x630 0x000 0x3 0x0 +#define MX50_PAD_EIM_DA14__TPIU_TRACE_14 0x294 0x630 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA14__SRC_BT_CFG2_6 0x294 0x630 0x000 0x7 0x0 +#define MX50_PAD_EIM_DA15__EIM_WEIM_A_15 0x298 0x634 0x000 0x0 0x0 +#define MX50_PAD_EIM_DA15__GPIO1_15 0x298 0x634 0x000 0x1 0x0 +#define MX50_PAD_EIM_DA15__EIM_NANDF_DQS 0x298 0x634 0x7b0 0x2 0x2 +#define MX50_PAD_EIM_DA15__EPDC_SDCE_9 0x298 0x634 0x000 0x3 0x0 +#define MX50_PAD_EIM_DA15__TPIU_TRACE_15 0x298 0x634 0x000 0x6 0x0 +#define MX50_PAD_EIM_DA15__SRC_BT_CFG2_7 0x298 0x634 0x000 0x7 0x0 +#define MX50_PAD_EIM_CS2__EIM_WEIM_CS_2 0x29c 0x638 0x000 0x0 0x0 +#define MX50_PAD_EIM_CS2__GPIO1_16 0x29c 0x638 0x000 0x1 0x0 +#define MX50_PAD_EIM_CS2__EIM_WEIM_A_27 0x29c 0x638 0x000 0x2 0x0 +#define MX50_PAD_EIM_CS2__TPIU_TRCLK 0x29c 0x638 0x000 0x6 0x0 +#define MX50_PAD_EIM_CS2__SRC_BT_CFG3_0 0x29c 0x638 0x000 0x7 0x0 +#define MX50_PAD_EIM_CS1__EIM_WEIM_CS_1 0x2a0 0x63c 0x000 0x0 0x0 +#define MX50_PAD_EIM_CS1__GPIO1_17 0x2a0 0x63c 0x000 0x1 0x0 +#define MX50_PAD_EIM_CS1__TPIU_TRCTL 0x2a0 0x63c 0x000 0x6 0x0 +#define MX50_PAD_EIM_CS1__SRC_BT_CFG3_1 0x2a0 0x63c 0x000 0x7 0x0 +#define MX50_PAD_EIM_CS0__EIM_WEIM_CS_0 0x2a4 0x640 0x000 0x0 0x0 +#define MX50_PAD_EIM_CS0__GPIO1_18 0x2a4 0x640 0x000 0x1 0x0 +#define MX50_PAD_EIM_CS0__SRC_BT_CFG3_2 0x2a4 0x640 0x000 0x7 0x0 +#define MX50_PAD_EIM_EB0__EIM_WEIM_EB_0 0x2a8 0x644 0x000 0x0 0x0 +#define MX50_PAD_EIM_EB0__GPIO1_19 0x2a8 0x644 0x000 0x1 0x0 +#define MX50_PAD_EIM_EB0__SRC_BT_CFG3_3 0x2a8 0x644 0x000 0x7 0x0 +#define MX50_PAD_EIM_EB1__EIM_WEIM_EB_1 0x2ac 0x648 0x000 0x0 0x0 +#define MX50_PAD_EIM_EB1__GPIO1_20 0x2ac 0x648 0x000 0x1 0x0 +#define MX50_PAD_EIM_EB1__SRC_BT_CFG3_4 0x2ac 0x648 0x000 0x7 0x0 +#define MX50_PAD_EIM_WAIT__EIM_WEIM_WAIT 0x2b0 0x64c 0x000 0x0 0x0 +#define MX50_PAD_EIM_WAIT__GPIO1_21 0x2b0 0x64c 0x000 0x1 0x0 +#define MX50_PAD_EIM_WAIT__EIM_WEIM_DTACK_B 0x2b0 0x64c 0x000 0x2 0x0 +#define MX50_PAD_EIM_WAIT__SRC_BT_CFG3_5 0x2b0 0x64c 0x000 0x7 0x0 +#define MX50_PAD_EIM_BCLK__EIM_WEIM_BCLK 0x2b4 0x650 0x000 0x0 0x0 +#define MX50_PAD_EIM_BCLK__GPIO1_22 0x2b4 0x650 0x000 0x1 0x0 +#define MX50_PAD_EIM_BCLK__SRC_BT_CFG3_6 0x2b4 0x650 0x000 0x7 0x0 +#define MX50_PAD_EIM_RDY__EIM_WEIM_RDY 0x2b8 0x654 0x000 0x0 0x0 +#define MX50_PAD_EIM_RDY__GPIO1_23 0x2b8 0x654 0x000 0x1 0x0 +#define MX50_PAD_EIM_RDY__SRC_BT_CFG3_7 0x2b8 0x654 0x000 0x7 0x0 +#define MX50_PAD_EIM_OE__EIM_WEIM_OE 0x2bc 0x658 0x000 0x0 0x0 +#define MX50_PAD_EIM_OE__GPIO1_24 0x2bc 0x658 0x000 0x1 0x0 +#define MX50_PAD_EIM_OE__INT_BOOT 0x2bc 0x658 0x000 0x7 0x0 +#define MX50_PAD_EIM_RW__EIM_WEIM_RW 0x2c0 0x65c 0x000 0x0 0x0 +#define MX50_PAD_EIM_RW__GPIO1_25 0x2c0 0x65c 0x000 0x1 0x0 +#define MX50_PAD_EIM_RW__SYSTEM_RST 0x2c0 0x65c 0x000 0x7 0x0 +#define MX50_PAD_EIM_LBA__EIM_WEIM_LBA 0x2c4 0x660 0x000 0x0 0x0 +#define MX50_PAD_EIM_LBA__GPIO1_26 0x2c4 0x660 0x000 0x1 0x0 +#define MX50_PAD_EIM_LBA__TESTER_ACK 0x2c4 0x660 0x000 0x7 0x0 +#define MX50_PAD_EIM_CRE__EIM_WEIM_CRE 0x2c8 0x664 0x000 0x0 0x0 +#define MX50_PAD_EIM_CRE__GPIO1_27 0x2c8 0x664 0x000 0x1 0x0 + +#endif /* __DTS_IMX50_PINFUNC_H */ diff --git a/arch/arm/boot/dts/imx50.dtsi b/arch/arm/boot/dts/imx50.dtsi new file mode 100644 index 000000000000..0c75fe3deb35 --- /dev/null +++ b/arch/arm/boot/dts/imx50.dtsi @@ -0,0 +1,478 @@ +/* + * Copyright 2013 Greg Ungerer <gerg@uclinux.org> + * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include "skeleton.dtsi" +#include "imx50-pinfunc.h" +#include <dt-bindings/clock/imx5-clock.h> + +/ { + aliases { + gpio0 = &gpio1; + gpio1 = &gpio2; + gpio2 = &gpio3; + gpio3 = &gpio4; + gpio4 = &gpio5; + gpio5 = &gpio6; + serial0 = &uart1; + serial1 = &uart2; + serial2 = &uart3; + serial3 = &uart4; + serial4 = &uart5; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + cpu@0 { + device_type = "cpu"; + compatible = "arm,cortex-a8"; + reg = <0x0>; + }; + }; + + tzic: tz-interrupt-controller@0fffc000 { + compatible = "fsl,imx50-tzic", "fsl,imx53-tzic", "fsl,tzic"; + interrupt-controller; + #interrupt-cells = <1>; + reg = <0x0fffc000 0x4000>; + }; + + clocks { + #address-cells = <1>; + #size-cells = <0>; + + ckil { + compatible = "fsl,imx-ckil", "fixed-clock"; + clock-frequency = <32768>; + }; + + ckih1 { + compatible = "fsl,imx-ckih1", "fixed-clock"; + clock-frequency = <22579200>; + }; + + ckih2 { + compatible = "fsl,imx-ckih2", "fixed-clock"; + clock-frequency = <0>; + }; + + osc { + compatible = "fsl,imx-osc", "fixed-clock"; + clock-frequency = <24000000>; + }; + }; + + soc { + #address-cells = <1>; + #size-cells = <1>; + compatible = "simple-bus"; + interrupt-parent = <&tzic>; + ranges; + + aips@50000000 { /* AIPS1 */ + compatible = "fsl,aips-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x50000000 0x10000000>; + ranges; + + spba@50000000 { + compatible = "fsl,spba-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x50000000 0x40000>; + ranges; + + esdhc1: esdhc@50004000 { + compatible = "fsl,imx50-esdhc"; + reg = <0x50004000 0x4000>; + interrupts = <1>; + clocks = <&clks IMX5_CLK_ESDHC1_IPG_GATE>, + <&clks IMX5_CLK_DUMMY>, + <&clks IMX5_CLK_ESDHC1_PER_GATE>; + clock-names = "ipg", "ahb", "per"; + bus-width = <4>; + status = "disabled"; + }; + + esdhc2: esdhc@50008000 { + compatible = "fsl,imx50-esdhc"; + reg = <0x50008000 0x4000>; + interrupts = <2>; + clocks = <&clks IMX5_CLK_ESDHC2_IPG_GATE>, + <&clks IMX5_CLK_DUMMY>, + <&clks IMX5_CLK_ESDHC2_PER_GATE>; + clock-names = "ipg", "ahb", "per"; + bus-width = <4>; + status = "disabled"; + }; + + uart3: serial@5000c000 { + compatible = "fsl,imx50-uart", "fsl,imx21-uart"; + reg = <0x5000c000 0x4000>; + interrupts = <33>; + clocks = <&clks IMX5_CLK_UART3_IPG_GATE>, + <&clks IMX5_CLK_UART3_PER_GATE>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + ecspi1: ecspi@50010000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx50-ecspi", "fsl,imx51-ecspi"; + reg = <0x50010000 0x4000>; + interrupts = <36>; + clocks = <&clks IMX5_CLK_ECSPI1_IPG_GATE>, + <&clks IMX5_CLK_ECSPI1_PER_GATE>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + ssi2: ssi@50014000 { + compatible = "fsl,imx50-ssi", + "fsl,imx51-ssi", + "fsl,imx21-ssi"; + reg = <0x50014000 0x4000>; + interrupts = <30>; + clocks = <&clks IMX5_CLK_SSI2_IPG_GATE>; + fsl,fifo-depth = <15>; + fsl,ssi-dma-events = <25 24 23 22>; /* TX0 RX0 TX1 RX1 */ + status = "disabled"; + }; + + esdhc3: esdhc@50020000 { + compatible = "fsl,imx50-esdhc"; + reg = <0x50020000 0x4000>; + interrupts = <3>; + clocks = <&clks IMX5_CLK_ESDHC3_IPG_GATE>, + <&clks IMX5_CLK_DUMMY>, + <&clks IMX5_CLK_ESDHC3_PER_GATE>; + clock-names = "ipg", "ahb", "per"; + bus-width = <4>; + status = "disabled"; + }; + + esdhc4: esdhc@50024000 { + compatible = "fsl,imx50-esdhc"; + reg = <0x50024000 0x4000>; + interrupts = <4>; + clocks = <&clks IMX5_CLK_ESDHC4_IPG_GATE>, + <&clks IMX5_CLK_DUMMY>, + <&clks IMX5_CLK_ESDHC4_PER_GATE>; + clock-names = "ipg", "ahb", "per"; + bus-width = <4>; + status = "disabled"; + }; + }; + + usbotg: usb@53f80000 { + compatible = "fsl,imx50-usb", "fsl,imx27-usb"; + reg = <0x53f80000 0x0200>; + interrupts = <18>; + clocks = <&clks IMX5_CLK_USB_PHY1_GATE>; + status = "disabled"; + }; + + usbh1: usb@53f80200 { + compatible = "fsl,imx50-usb", "fsl,imx27-usb"; + reg = <0x53f80200 0x0200>; + interrupts = <14>; + clocks = <&clks IMX5_CLK_USB_PHY2_GATE>; + status = "disabled"; + }; + + usbh2: usb@53f80400 { + compatible = "fsl,imx50-usb", "fsl,imx27-usb"; + reg = <0x53f80400 0x0200>; + interrupts = <16>; + clocks = <&clks IMX5_CLK_USBOH3_GATE>; + status = "disabled"; + }; + + usbh3: usb@53f80600 { + compatible = "fsl,imx50-usb", "fsl,imx27-usb"; + reg = <0x53f80600 0x0200>; + interrupts = <17>; + clocks = <&clks IMX5_CLK_USBOH3_GATE>; + status = "disabled"; + }; + + gpio1: gpio@53f84000 { + compatible = "fsl,imx50-gpio", "fsl,imx35-gpio"; + reg = <0x53f84000 0x4000>; + interrupts = <50 51>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio@53f88000 { + compatible = "fsl,imx50-gpio", "fsl,imx35-gpio"; + reg = <0x53f88000 0x4000>; + interrupts = <52 53>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio3: gpio@53f8c000 { + compatible = "fsl,imx50-gpio", "fsl,imx35-gpio"; + reg = <0x53f8c000 0x4000>; + interrupts = <54 55>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio4: gpio@53f90000 { + compatible = "fsl,imx50-gpio", "fsl,imx35-gpio"; + reg = <0x53f90000 0x4000>; + interrupts = <56 57>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + wdog1: wdog@53f98000 { + compatible = "fsl,imx50-wdt", "fsl,imx21-wdt"; + reg = <0x53f98000 0x4000>; + interrupts = <58>; + clocks = <&clks IMX5_CLK_DUMMY>; + }; + + gpt: timer@53fa0000 { + compatible = "fsl,imx50-gpt", "fsl,imx31-gpt"; + reg = <0x53fa0000 0x4000>; + interrupts = <39>; + clocks = <&clks IMX5_CLK_GPT_IPG_GATE>, + <&clks IMX5_CLK_GPT_HF_GATE>; + clock-names = "ipg", "per"; + }; + + iomuxc: iomuxc@53fa8000 { + compatible = "fsl,imx50-iomuxc", "fsl,imx53-iomuxc"; + reg = <0x53fa8000 0x4000>; + }; + + gpr: iomuxc-gpr@53fa8000 { + compatible = "fsl,imx50-iomuxc-gpr", "syscon"; + reg = <0x53fa8000 0xc>; + }; + + pwm1: pwm@53fb4000 { + #pwm-cells = <2>; + compatible = "fsl,imx50-pwm", "fsl,imx27-pwm"; + reg = <0x53fb4000 0x4000>; + clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>, + <&clks IMX5_CLK_PWM1_HF_GATE>; + clock-names = "ipg", "per"; + interrupts = <61>; + }; + + pwm2: pwm@53fb8000 { + #pwm-cells = <2>; + compatible = "fsl,imx50-pwm", "fsl,imx27-pwm"; + reg = <0x53fb8000 0x4000>; + clocks = <&clks IMX5_CLK_PWM2_IPG_GATE>, + <&clks IMX5_CLK_PWM2_HF_GATE>; + clock-names = "ipg", "per"; + interrupts = <94>; + }; + + uart1: serial@53fbc000 { + compatible = "fsl,imx50-uart", "fsl,imx21-uart"; + reg = <0x53fbc000 0x4000>; + interrupts = <31>; + clocks = <&clks IMX5_CLK_UART1_IPG_GATE>, + <&clks IMX5_CLK_UART1_PER_GATE>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + uart2: serial@53fc0000 { + compatible = "fsl,imx50-uart", "fsl,imx21-uart"; + reg = <0x53fc0000 0x4000>; + interrupts = <32>; + clocks = <&clks IMX5_CLK_UART2_IPG_GATE>, + <&clks IMX5_CLK_UART2_PER_GATE>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + src: src@53fd0000 { + compatible = "fsl,imx50-src", "fsl,imx51-src"; + reg = <0x53fd0000 0x4000>; + #reset-cells = <1>; + }; + + clks: ccm@53fd4000{ + compatible = "fsl,imx50-ccm"; + reg = <0x53fd4000 0x4000>; + interrupts = <0 71 0x04 0 72 0x04>; + #clock-cells = <1>; + }; + + gpio5: gpio@53fdc000 { + compatible = "fsl,imx50-gpio", "fsl,imx35-gpio"; + reg = <0x53fdc000 0x4000>; + interrupts = <103 104>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio6: gpio@53fe0000 { + compatible = "fsl,imx50-gpio", "fsl,imx35-gpio"; + reg = <0x53fe0000 0x4000>; + interrupts = <105 106>; + gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + i2c3: i2c@53fec000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx50-i2c", "fsl,imx21-i2c"; + reg = <0x53fec000 0x4000>; + interrupts = <64>; + clocks = <&clks IMX5_CLK_I2C3_GATE>; + status = "disabled"; + }; + + uart4: serial@53ff0000 { + compatible = "fsl,imx50-uart", "fsl,imx21-uart"; + reg = <0x53ff0000 0x4000>; + interrupts = <13>; + clocks = <&clks IMX5_CLK_UART4_IPG_GATE>, + <&clks IMX5_CLK_UART4_PER_GATE>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + }; + + aips@60000000 { /* AIPS2 */ + compatible = "fsl,aips-bus", "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x60000000 0x10000000>; + ranges; + + uart5: serial@63f90000 { + compatible = "fsl,imx50-uart", "fsl,imx21-uart"; + reg = <0x63f90000 0x4000>; + interrupts = <86>; + clocks = <&clks IMX5_CLK_UART5_IPG_GATE>, + <&clks IMX5_CLK_UART5_PER_GATE>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + owire: owire@63fa4000 { + compatible = "fsl,imx50-owire", "fsl,imx21-owire"; + reg = <0x63fa4000 0x4000>; + clocks = <&clks IMX5_CLK_OWIRE_GATE>; + status = "disabled"; + }; + + ecspi2: ecspi@63fac000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx50-ecspi", "fsl,imx51-ecspi"; + reg = <0x63fac000 0x4000>; + interrupts = <37>; + clocks = <&clks IMX5_CLK_ECSPI2_IPG_GATE>, + <&clks IMX5_CLK_ECSPI2_PER_GATE>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + sdma: sdma@63fb0000 { + compatible = "fsl,imx50-sdma", "fsl,imx35-sdma"; + reg = <0x63fb0000 0x4000>; + interrupts = <6>; + clocks = <&clks IMX5_CLK_SDMA_GATE>, + <&clks IMX5_CLK_SDMA_GATE>; + clock-names = "ipg", "ahb"; + fsl,sdma-ram-script-name = "imx/sdma/sdma-imx50.bin"; + }; + + cspi: cspi@63fc0000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx50-cspi", "fsl,imx35-cspi"; + reg = <0x63fc0000 0x4000>; + interrupts = <38>; + clocks = <&clks IMX5_CLK_CSPI_IPG_GATE>, + <&clks IMX5_CLK_CSPI_IPG_GATE>; + clock-names = "ipg", "per"; + status = "disabled"; + }; + + i2c2: i2c@63fc4000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx50-i2c", "fsl,imx21-i2c"; + reg = <0x63fc4000 0x4000>; + interrupts = <63>; + clocks = <&clks IMX5_CLK_I2C2_GATE>; + status = "disabled"; + }; + + i2c1: i2c@63fc8000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx50-i2c", "fsl,imx21-i2c"; + reg = <0x63fc8000 0x4000>; + interrupts = <62>; + clocks = <&clks IMX5_CLK_I2C1_GATE>; + status = "disabled"; + }; + + ssi1: ssi@63fcc000 { + compatible = "fsl,imx50-ssi", "fsl,imx51-ssi", + "fsl,imx21-ssi"; + reg = <0x63fcc000 0x4000>; + interrupts = <29>; + clocks = <&clks IMX5_CLK_SSI1_IPG_GATE>; + fsl,fifo-depth = <15>; + fsl,ssi-dma-events = <29 28 27 26>; /* TX0 RX0 TX1 RX1 */ + status = "disabled"; + }; + + audmux: audmux@63fd0000 { + compatible = "fsl,imx50-audmux", "fsl,imx31-audmux"; + reg = <0x63fd0000 0x4000>; + status = "disabled"; + }; + + fec: ethernet@63fec000 { + compatible = "fsl,imx53-fec", "fsl,imx25-fec"; + reg = <0x63fec000 0x4000>; + interrupts = <87>; + clocks = <&clks IMX5_CLK_FEC_GATE>, + <&clks IMX5_CLK_FEC_GATE>, + <&clks IMX5_CLK_FEC_GATE>; + clock-names = "ipg", "ahb", "ptp"; + status = "disabled"; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx51-apf51.dts b/arch/arm/boot/dts/imx51-apf51.dts index b3606993f2e8..e88b2a6be079 100644 --- a/arch/arm/boot/dts/imx51-apf51.dts +++ b/arch/arm/boot/dts/imx51-apf51.dts @@ -34,13 +34,47 @@ &fec { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec_2>; + pinctrl-0 = <&pinctrl_fec>; phy-mode = "mii"; - phy-reset-gpios = <&gpio3 0 0>; + phy-reset-gpios = <&gpio3 0 GPIO_ACTIVE_HIGH>; phy-reset-duration = <1>; status = "okay"; }; +&iomuxc { + imx51-apf51 { + pinctrl_fec: fecgrp { + fsl,pins = < + MX51_PAD_DI_GP3__FEC_TX_ER 0x80000000 + MX51_PAD_DI2_PIN4__FEC_CRS 0x80000000 + MX51_PAD_DI2_PIN2__FEC_MDC 0x80000000 + MX51_PAD_DI2_PIN3__FEC_MDIO 0x80000000 + MX51_PAD_DI2_DISP_CLK__FEC_RDATA1 0x80000000 + MX51_PAD_DI_GP4__FEC_RDATA2 0x80000000 + MX51_PAD_DISP2_DAT0__FEC_RDATA3 0x80000000 + MX51_PAD_DISP2_DAT1__FEC_RX_ER 0x80000000 + MX51_PAD_DISP2_DAT6__FEC_TDATA1 0x80000000 + MX51_PAD_DISP2_DAT7__FEC_TDATA2 0x80000000 + MX51_PAD_DISP2_DAT8__FEC_TDATA3 0x80000000 + MX51_PAD_DISP2_DAT9__FEC_TX_EN 0x80000000 + MX51_PAD_DISP2_DAT10__FEC_COL 0x80000000 + MX51_PAD_DISP2_DAT11__FEC_RX_CLK 0x80000000 + MX51_PAD_DISP2_DAT12__FEC_RX_DV 0x80000000 + MX51_PAD_DISP2_DAT13__FEC_TX_CLK 0x80000000 + MX51_PAD_DISP2_DAT14__FEC_RDATA0 0x80000000 + MX51_PAD_DISP2_DAT15__FEC_TDATA0 0x80000000 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX51_PAD_UART3_RXD__UART3_RXD 0x1c5 + MX51_PAD_UART3_TXD__UART3_TXD 0x1c5 + >; + }; + }; +}; + &nfc { nand-bus-width = <8>; nand-ecc-mode = "hw"; @@ -50,6 +84,6 @@ &uart3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart3_2>; + pinctrl-0 = <&pinctrl_uart3>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx51-apf51dev.dts b/arch/arm/boot/dts/imx51-apf51dev.dts index d3f98141462c..c5a9a24c280a 100644 --- a/arch/arm/boot/dts/imx51-apf51dev.dts +++ b/arch/arm/boot/dts/imx51-apf51dev.dts @@ -20,7 +20,7 @@ compatible = "fsl,imx-parallel-display"; interface-pix-fmt = "bgr666"; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ipu_disp1_1>; + pinctrl-0 = <&pinctrl_ipu_disp1>; display-timings { lw700 { @@ -53,7 +53,7 @@ user-key { label = "user"; - gpios = <&gpio1 3 0>; + gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; linux,code = <256>; /* BTN_0 */ }; }; @@ -63,7 +63,7 @@ user { label = "Heartbeat"; - gpios = <&gpio1 2 0>; + gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; }; @@ -71,31 +71,33 @@ &ecspi1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi1_1>; + pinctrl-0 = <&pinctrl_ecspi1>; fsl,spi-num-chipselects = <2>; - cs-gpios = <&gpio4 24 0>, <&gpio4 25 0>; + cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>, + <&gpio4 25 GPIO_ACTIVE_HIGH>; status = "okay"; }; &ecspi2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi2_1>; + pinctrl-0 = <&pinctrl_ecspi2>; fsl,spi-num-chipselects = <2>; - cs-gpios = <&gpio3 28 1>, <&gpio3 27 1>; + cs-gpios = <&gpio3 28 GPIO_ACTIVE_LOW>, + <&gpio3 27 GPIO_ACTIVE_LOW>; status = "okay"; }; &esdhc1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc1_1>; - cd-gpios = <&gpio2 29 0>; + pinctrl-0 = <&pinctrl_esdhc1>; + cd-gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; bus-width = <4>; status = "okay"; }; &esdhc2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc2_1>; + pinctrl-0 = <&pinctrl_esdhc2>; bus-width = <4>; non-removable; status = "okay"; @@ -103,7 +105,7 @@ &i2c2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2_2>; + pinctrl-0 = <&pinctrl_i2c2>; status = "okay"; }; @@ -111,7 +113,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; - hog { + imx51-apf51dev { pinctrl_hog: hoggrp { fsl,pins = < MX51_PAD_EIM_EB2__GPIO2_22 0x0C5 @@ -125,6 +127,82 @@ MX51_PAD_GPIO1_3__GPIO1_3 0x0C5 >; }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX51_PAD_CSPI1_MISO__ECSPI1_MISO 0x185 + MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI 0x185 + MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK 0x185 + >; + }; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX51_PAD_NANDF_RB3__ECSPI2_MISO 0x185 + MX51_PAD_NANDF_D15__ECSPI2_MOSI 0x185 + MX51_PAD_NANDF_RB2__ECSPI2_SCLK 0x185 + >; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + MX51_PAD_SD1_CMD__SD1_CMD 0x400020d5 + MX51_PAD_SD1_CLK__SD1_CLK 0x20d5 + MX51_PAD_SD1_DATA0__SD1_DATA0 0x20d5 + MX51_PAD_SD1_DATA1__SD1_DATA1 0x20d5 + MX51_PAD_SD1_DATA2__SD1_DATA2 0x20d5 + MX51_PAD_SD1_DATA3__SD1_DATA3 0x20d5 + >; + }; + + pinctrl_esdhc2: esdhc2grp { + fsl,pins = < + MX51_PAD_SD2_CMD__SD2_CMD 0x400020d5 + MX51_PAD_SD2_CLK__SD2_CLK 0x20d5 + MX51_PAD_SD2_DATA0__SD2_DATA0 0x20d5 + MX51_PAD_SD2_DATA1__SD2_DATA1 0x20d5 + MX51_PAD_SD2_DATA2__SD2_DATA2 0x20d5 + MX51_PAD_SD2_DATA3__SD2_DATA3 0x20d5 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX51_PAD_EIM_D27__I2C2_SCL 0x400001ed + MX51_PAD_EIM_D24__I2C2_SDA 0x400001ed + >; + }; + + pinctrl_ipu_disp1: ipudisp1grp { + fsl,pins = < + MX51_PAD_DISP1_DAT0__DISP1_DAT0 0x5 + MX51_PAD_DISP1_DAT1__DISP1_DAT1 0x5 + MX51_PAD_DISP1_DAT2__DISP1_DAT2 0x5 + MX51_PAD_DISP1_DAT3__DISP1_DAT3 0x5 + MX51_PAD_DISP1_DAT4__DISP1_DAT4 0x5 + MX51_PAD_DISP1_DAT5__DISP1_DAT5 0x5 + MX51_PAD_DISP1_DAT6__DISP1_DAT6 0x5 + MX51_PAD_DISP1_DAT7__DISP1_DAT7 0x5 + MX51_PAD_DISP1_DAT8__DISP1_DAT8 0x5 + MX51_PAD_DISP1_DAT9__DISP1_DAT9 0x5 + MX51_PAD_DISP1_DAT10__DISP1_DAT10 0x5 + MX51_PAD_DISP1_DAT11__DISP1_DAT11 0x5 + MX51_PAD_DISP1_DAT12__DISP1_DAT12 0x5 + MX51_PAD_DISP1_DAT13__DISP1_DAT13 0x5 + MX51_PAD_DISP1_DAT14__DISP1_DAT14 0x5 + MX51_PAD_DISP1_DAT15__DISP1_DAT15 0x5 + MX51_PAD_DISP1_DAT16__DISP1_DAT16 0x5 + MX51_PAD_DISP1_DAT17__DISP1_DAT17 0x5 + MX51_PAD_DISP1_DAT18__DISP1_DAT18 0x5 + MX51_PAD_DISP1_DAT19__DISP1_DAT19 0x5 + MX51_PAD_DISP1_DAT20__DISP1_DAT20 0x5 + MX51_PAD_DISP1_DAT21__DISP1_DAT21 0x5 + MX51_PAD_DISP1_DAT22__DISP1_DAT22 0x5 + MX51_PAD_DISP1_DAT23__DISP1_DAT23 0x5 + MX51_PAD_DI1_PIN2__DI1_PIN2 0x5 + MX51_PAD_DI1_PIN3__DI1_PIN3 0x5 + >; + }; }; }; diff --git a/arch/arm/boot/dts/imx51-babbage.dts b/arch/arm/boot/dts/imx51-babbage.dts index 671927145632..9e9deb244b76 100644 --- a/arch/arm/boot/dts/imx51-babbage.dts +++ b/arch/arm/boot/dts/imx51-babbage.dts @@ -25,7 +25,7 @@ compatible = "fsl,imx-parallel-display"; interface-pix-fmt = "rgb24"; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ipu_disp1_1>; + pinctrl-0 = <&pinctrl_ipu_disp1>; display-timings { native-mode = <&timing0>; timing0: dvi { @@ -52,7 +52,7 @@ compatible = "fsl,imx-parallel-display"; interface-pix-fmt = "rgb565"; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ipu_disp2_1>; + pinctrl-0 = <&pinctrl_ipu_disp2>; status = "disabled"; display-timings { native-mode = <&timing1>; @@ -85,12 +85,23 @@ power { label = "Power Button"; - gpios = <&gpio2 21 0>; + gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; linux,code = <116>; /* KEY_POWER */ gpio-key,wakeup; }; }; + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + led-diagnostic { + label = "diagnostic"; + gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>; + }; + }; + sound { compatible = "fsl,imx51-babbage-sgtl5000", "fsl,imx-audio-sgtl5000"; @@ -115,14 +126,14 @@ reg=<0>; #clock-cells = <0>; clock-frequency = <26000000>; - gpios = <&gpio4 26 1>; + gpios = <&gpio4 26 GPIO_ACTIVE_LOW>; }; }; }; &esdhc1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc1_1>; + pinctrl-0 = <&pinctrl_esdhc1>; fsl,cd-controller; fsl,wp-controller; status = "okay"; @@ -130,24 +141,25 @@ &esdhc2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc2_1>; - cd-gpios = <&gpio1 6 0>; - wp-gpios = <&gpio1 5 0>; + pinctrl-0 = <&pinctrl_esdhc2>; + cd-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + wp-gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; status = "okay"; }; &uart3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart3_1 &pinctrl_uart3_rtscts_1>; + pinctrl-0 = <&pinctrl_uart3>; fsl,uart-has-rtscts; status = "okay"; }; &ecspi1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi1_1>; + pinctrl-0 = <&pinctrl_ecspi1>; fsl,spi-num-chipselects = <2>; - cs-gpios = <&gpio4 24 0>, <&gpio4 25 0>; + cs-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>, + <&gpio4 25 GPIO_ACTIVE_LOW>; status = "okay"; pmic: mc13892@0 { @@ -158,7 +170,7 @@ spi-cs-high; reg = <0>; interrupt-parent = <&gpio1>; - interrupts = <8 0x4>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>; regulators { sw1_reg: sw1 { @@ -285,7 +297,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; - hog { + imx51-babbage { pinctrl_hog: hoggrp { fsl,pins = < MX51_PAD_GPIO1_0__SD1_CD 0x20d5 @@ -298,25 +310,194 @@ MX51_PAD_CSPI1_RDY__GPIO4_26 0x80000000 >; }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX51_PAD_AUD3_BB_TXD__AUD3_TXD 0x80000000 + MX51_PAD_AUD3_BB_RXD__AUD3_RXD 0x80000000 + MX51_PAD_AUD3_BB_CK__AUD3_TXC 0x80000000 + MX51_PAD_AUD3_BB_FS__AUD3_TXFS 0x80000000 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX51_PAD_CSPI1_MISO__ECSPI1_MISO 0x185 + MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI 0x185 + MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK 0x185 + >; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + MX51_PAD_SD1_CMD__SD1_CMD 0x400020d5 + MX51_PAD_SD1_CLK__SD1_CLK 0x20d5 + MX51_PAD_SD1_DATA0__SD1_DATA0 0x20d5 + MX51_PAD_SD1_DATA1__SD1_DATA1 0x20d5 + MX51_PAD_SD1_DATA2__SD1_DATA2 0x20d5 + MX51_PAD_SD1_DATA3__SD1_DATA3 0x20d5 + >; + }; + + pinctrl_esdhc2: esdhc2grp { + fsl,pins = < + MX51_PAD_SD2_CMD__SD2_CMD 0x400020d5 + MX51_PAD_SD2_CLK__SD2_CLK 0x20d5 + MX51_PAD_SD2_DATA0__SD2_DATA0 0x20d5 + MX51_PAD_SD2_DATA1__SD2_DATA1 0x20d5 + MX51_PAD_SD2_DATA2__SD2_DATA2 0x20d5 + MX51_PAD_SD2_DATA3__SD2_DATA3 0x20d5 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX51_PAD_EIM_EB2__FEC_MDIO 0x80000000 + MX51_PAD_EIM_EB3__FEC_RDATA1 0x80000000 + MX51_PAD_EIM_CS2__FEC_RDATA2 0x80000000 + MX51_PAD_EIM_CS3__FEC_RDATA3 0x80000000 + MX51_PAD_EIM_CS4__FEC_RX_ER 0x80000000 + MX51_PAD_EIM_CS5__FEC_CRS 0x80000000 + MX51_PAD_NANDF_RB2__FEC_COL 0x80000000 + MX51_PAD_NANDF_RB3__FEC_RX_CLK 0x80000000 + MX51_PAD_NANDF_D9__FEC_RDATA0 0x80000000 + MX51_PAD_NANDF_D8__FEC_TDATA0 0x80000000 + MX51_PAD_NANDF_CS2__FEC_TX_ER 0x80000000 + MX51_PAD_NANDF_CS3__FEC_MDC 0x80000000 + MX51_PAD_NANDF_CS4__FEC_TDATA1 0x80000000 + MX51_PAD_NANDF_CS5__FEC_TDATA2 0x80000000 + MX51_PAD_NANDF_CS6__FEC_TDATA3 0x80000000 + MX51_PAD_NANDF_CS7__FEC_TX_EN 0x80000000 + MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK 0x80000000 + MX51_PAD_EIM_A20__GPIO2_14 0x85 /* Reset */ + >; + }; + + pinctrl_gpio_leds: gpioledsgrp { + fsl,pins = < + MX51_PAD_EIM_D22__GPIO2_6 0x80000000 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX51_PAD_KEY_COL4__I2C2_SCL 0x400001ed + MX51_PAD_KEY_COL5__I2C2_SDA 0x400001ed + >; + }; + + pinctrl_ipu_disp1: ipudisp1grp { + fsl,pins = < + MX51_PAD_DISP1_DAT0__DISP1_DAT0 0x5 + MX51_PAD_DISP1_DAT1__DISP1_DAT1 0x5 + MX51_PAD_DISP1_DAT2__DISP1_DAT2 0x5 + MX51_PAD_DISP1_DAT3__DISP1_DAT3 0x5 + MX51_PAD_DISP1_DAT4__DISP1_DAT4 0x5 + MX51_PAD_DISP1_DAT5__DISP1_DAT5 0x5 + MX51_PAD_DISP1_DAT6__DISP1_DAT6 0x5 + MX51_PAD_DISP1_DAT7__DISP1_DAT7 0x5 + MX51_PAD_DISP1_DAT8__DISP1_DAT8 0x5 + MX51_PAD_DISP1_DAT9__DISP1_DAT9 0x5 + MX51_PAD_DISP1_DAT10__DISP1_DAT10 0x5 + MX51_PAD_DISP1_DAT11__DISP1_DAT11 0x5 + MX51_PAD_DISP1_DAT12__DISP1_DAT12 0x5 + MX51_PAD_DISP1_DAT13__DISP1_DAT13 0x5 + MX51_PAD_DISP1_DAT14__DISP1_DAT14 0x5 + MX51_PAD_DISP1_DAT15__DISP1_DAT15 0x5 + MX51_PAD_DISP1_DAT16__DISP1_DAT16 0x5 + MX51_PAD_DISP1_DAT17__DISP1_DAT17 0x5 + MX51_PAD_DISP1_DAT18__DISP1_DAT18 0x5 + MX51_PAD_DISP1_DAT19__DISP1_DAT19 0x5 + MX51_PAD_DISP1_DAT20__DISP1_DAT20 0x5 + MX51_PAD_DISP1_DAT21__DISP1_DAT21 0x5 + MX51_PAD_DISP1_DAT22__DISP1_DAT22 0x5 + MX51_PAD_DISP1_DAT23__DISP1_DAT23 0x5 + MX51_PAD_DI1_PIN2__DI1_PIN2 0x5 + MX51_PAD_DI1_PIN3__DI1_PIN3 0x5 + >; + }; + + pinctrl_ipu_disp2: ipudisp2grp { + fsl,pins = < + MX51_PAD_DISP2_DAT0__DISP2_DAT0 0x5 + MX51_PAD_DISP2_DAT1__DISP2_DAT1 0x5 + MX51_PAD_DISP2_DAT2__DISP2_DAT2 0x5 + MX51_PAD_DISP2_DAT3__DISP2_DAT3 0x5 + MX51_PAD_DISP2_DAT4__DISP2_DAT4 0x5 + MX51_PAD_DISP2_DAT5__DISP2_DAT5 0x5 + MX51_PAD_DISP2_DAT6__DISP2_DAT6 0x5 + MX51_PAD_DISP2_DAT7__DISP2_DAT7 0x5 + MX51_PAD_DISP2_DAT8__DISP2_DAT8 0x5 + MX51_PAD_DISP2_DAT9__DISP2_DAT9 0x5 + MX51_PAD_DISP2_DAT10__DISP2_DAT10 0x5 + MX51_PAD_DISP2_DAT11__DISP2_DAT11 0x5 + MX51_PAD_DISP2_DAT12__DISP2_DAT12 0x5 + MX51_PAD_DISP2_DAT13__DISP2_DAT13 0x5 + MX51_PAD_DISP2_DAT14__DISP2_DAT14 0x5 + MX51_PAD_DISP2_DAT15__DISP2_DAT15 0x5 + MX51_PAD_DI2_PIN2__DI2_PIN2 0x5 + MX51_PAD_DI2_PIN3__DI2_PIN3 0x5 + MX51_PAD_DI2_DISP_CLK__DI2_DISP_CLK 0x5 + MX51_PAD_DI_GP4__DI2_PIN15 0x5 + >; + }; + + pinctrl_kpp: kppgrp { + fsl,pins = < + MX51_PAD_KEY_ROW0__KEY_ROW0 0xe0 + MX51_PAD_KEY_ROW1__KEY_ROW1 0xe0 + MX51_PAD_KEY_ROW2__KEY_ROW2 0xe0 + MX51_PAD_KEY_ROW3__KEY_ROW3 0xe0 + MX51_PAD_KEY_COL0__KEY_COL0 0xe8 + MX51_PAD_KEY_COL1__KEY_COL1 0xe8 + MX51_PAD_KEY_COL2__KEY_COL2 0xe8 + MX51_PAD_KEY_COL3__KEY_COL3 0xe8 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX51_PAD_UART1_RXD__UART1_RXD 0x1c5 + MX51_PAD_UART1_TXD__UART1_TXD 0x1c5 + MX51_PAD_UART1_RTS__UART1_RTS 0x1c5 + MX51_PAD_UART1_CTS__UART1_CTS 0x1c5 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX51_PAD_UART2_RXD__UART2_RXD 0x1c5 + MX51_PAD_UART2_TXD__UART2_TXD 0x1c5 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX51_PAD_EIM_D25__UART3_RXD 0x1c5 + MX51_PAD_EIM_D26__UART3_TXD 0x1c5 + MX51_PAD_EIM_D27__UART3_RTS 0x1c5 + MX51_PAD_EIM_D24__UART3_CTS 0x1c5 + >; + }; }; }; &uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_1 &pinctrl_uart1_rtscts_1>; + pinctrl-0 = <&pinctrl_uart1>; fsl,uart-has-rtscts; status = "okay"; }; &uart2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2_1>; + pinctrl-0 = <&pinctrl_uart2>; status = "okay"; }; &i2c2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2_1>; + pinctrl-0 = <&pinctrl_i2c2>; status = "okay"; sgtl5000: codec@0a { @@ -330,35 +511,39 @@ &audmux { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_audmux_1>; + pinctrl-0 = <&pinctrl_audmux>; status = "okay"; }; &fec { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec_1>; + pinctrl-0 = <&pinctrl_fec>; phy-mode = "mii"; + phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>; + phy-reset-duration = <1>; status = "okay"; }; &kpp { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_kpp_1>; - linux,keymap = <0x00000067 /* KEY_UP */ - 0x0001006c /* KEY_DOWN */ - 0x00020072 /* KEY_VOLUMEDOWN */ - 0x00030066 /* KEY_HOME */ - 0x0100006a /* KEY_RIGHT */ - 0x01010069 /* KEY_LEFT */ - 0x0102001c /* KEY_ENTER */ - 0x01030073 /* KEY_VOLUMEUP */ - 0x02000040 /* KEY_F6 */ - 0x02010042 /* KEY_F8 */ - 0x02020043 /* KEY_F9 */ - 0x02030044 /* KEY_F10 */ - 0x0300003b /* KEY_F1 */ - 0x0301003c /* KEY_F2 */ - 0x0302003d /* KEY_F3 */ - 0x03030074>; /* KEY_POWER */ + pinctrl-0 = <&pinctrl_kpp>; + linux,keymap = < + MATRIX_KEY(0, 0, KEY_UP) + MATRIX_KEY(0, 1, KEY_DOWN) + MATRIX_KEY(0, 2, KEY_VOLUMEDOWN) + MATRIX_KEY(0, 3, KEY_HOME) + MATRIX_KEY(1, 0, KEY_RIGHT) + MATRIX_KEY(1, 1, KEY_LEFT) + MATRIX_KEY(1, 2, KEY_ENTER) + MATRIX_KEY(1, 3, KEY_VOLUMEUP) + MATRIX_KEY(2, 0, KEY_F6) + MATRIX_KEY(2, 1, KEY_F8) + MATRIX_KEY(2, 2, KEY_F9) + MATRIX_KEY(2, 3, KEY_F10) + MATRIX_KEY(3, 0, KEY_F1) + MATRIX_KEY(3, 1, KEY_F2) + MATRIX_KEY(3, 2, KEY_F3) + MATRIX_KEY(3, 3, KEY_POWER) + >; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi b/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi new file mode 100644 index 000000000000..9b3acf6e4282 --- /dev/null +++ b/arch/arm/boot/dts/imx51-eukrea-cpuimx51.dtsi @@ -0,0 +1,93 @@ +/* + * Copyright 2013 Eukréa Electromatique <denis@eukrea.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +#include "imx51.dtsi" + +/ { + model = "Eukrea CPUIMX51"; + compatible = "eukrea,cpuimx51", "fsl,imx51"; + + memory { + reg = <0x90000000 0x10000000>; /* 256M */ + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pcf8563@51 { + compatible = "nxp,pcf8563"; + reg = <0x51>; + }; +}; + +&iomuxc { + imx51-eukrea { + pinctrl_tsc2007_1: tsc2007grp-1 { + fsl,pins = < + MX51_PAD_GPIO_NAND__GPIO_NAND 0x1f5 + MX51_PAD_NANDF_D8__GPIO4_0 0x1f5 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX51_PAD_DI_GP3__FEC_TX_ER 0x80000000 + MX51_PAD_DI2_PIN4__FEC_CRS 0x80000000 + MX51_PAD_DI2_PIN2__FEC_MDC 0x80000000 + MX51_PAD_DI2_PIN3__FEC_MDIO 0x80000000 + MX51_PAD_DI2_DISP_CLK__FEC_RDATA1 0x80000000 + MX51_PAD_DI_GP4__FEC_RDATA2 0x80000000 + MX51_PAD_DISP2_DAT0__FEC_RDATA3 0x80000000 + MX51_PAD_DISP2_DAT1__FEC_RX_ER 0x80000000 + MX51_PAD_DISP2_DAT6__FEC_TDATA1 0x80000000 + MX51_PAD_DISP2_DAT7__FEC_TDATA2 0x80000000 + MX51_PAD_DISP2_DAT8__FEC_TDATA3 0x80000000 + MX51_PAD_DISP2_DAT9__FEC_TX_EN 0x80000000 + MX51_PAD_DISP2_DAT10__FEC_COL 0x80000000 + MX51_PAD_DISP2_DAT11__FEC_RX_CLK 0x80000000 + MX51_PAD_DISP2_DAT12__FEC_RX_DV 0x80000000 + MX51_PAD_DISP2_DAT13__FEC_TX_CLK 0x80000000 + MX51_PAD_DISP2_DAT14__FEC_RDATA0 0x80000000 + MX51_PAD_DISP2_DAT15__FEC_TDATA0 0x80000000 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX51_PAD_SD2_CMD__I2C1_SCL 0x400001ed + MX51_PAD_SD2_CLK__I2C1_SDA 0x400001ed + >; + }; + }; +}; + +&nfc { + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts b/arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts new file mode 100644 index 000000000000..5cec4f322096 --- /dev/null +++ b/arch/arm/boot/dts/imx51-eukrea-mbimxsd51-baseboard.dts @@ -0,0 +1,175 @@ +/* + * Copyright 2013 Eukréa Electromatique <denis@eukrea.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version 2 + * of the License, or (at your option) any later version. + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, + * MA 02110-1301, USA. + */ + +/dts-v1/; +#include "imx51-eukrea-cpuimx51.dtsi" +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Eukrea CPUIMX51"; + compatible = "eukrea,mbimxsd51","eukrea,cpuimx51", "fsl,imx51"; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpiokeys_1>; + + button-1 { + label = "BP1"; + gpios = <&gpio3 31 GPIO_ACTIVE_LOW>; + linux,code = <256>; + gpio-key,wakeup; + linux,input-type = <1>; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpioled>; + + led1 { + label = "led1"; + gpios = <&gpio3 30 GPIO_ACTIVE_LOW>; + linux,default-trigger = "heartbeat"; + }; + }; + + sound { + compatible = "eukrea,asoc-tlv320"; + eukrea,model = "imx51-eukrea-tlv320aic23"; + ssi-controller = <&ssi2>; + fsl,mux-int-port = <2>; + fsl,mux-ext-port = <3>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&esdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc1 &pinctrl_esdhc1_cd>; + fsl,cd-controller; + status = "okay"; +}; + +&i2c1 { + tlv320aic23: codec@1a { + compatible = "ti,tlv320aic23"; + reg = <0x1a>; + }; +}; + +&iomuxc { + imx51-eukrea { + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX51_PAD_AUD3_BB_TXD__AUD3_TXD 0x80000000 + MX51_PAD_AUD3_BB_RXD__AUD3_RXD 0x80000000 + MX51_PAD_AUD3_BB_CK__AUD3_TXC 0x80000000 + MX51_PAD_AUD3_BB_FS__AUD3_TXFS 0x80000000 + >; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + MX51_PAD_SD1_CMD__SD1_CMD 0x400020d5 + MX51_PAD_SD1_CLK__SD1_CLK 0x20d5 + MX51_PAD_SD1_DATA0__SD1_DATA0 0x20d5 + MX51_PAD_SD1_DATA1__SD1_DATA1 0x20d5 + MX51_PAD_SD1_DATA2__SD1_DATA2 0x20d5 + MX51_PAD_SD1_DATA3__SD1_DATA3 0x20d5 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX51_PAD_UART1_RXD__UART1_RXD 0x1c5 + MX51_PAD_UART1_TXD__UART1_TXD 0x1c5 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX51_PAD_UART3_RXD__UART3_RXD 0x1c5 + MX51_PAD_UART3_TXD__UART3_TXD 0x1c5 + >; + }; + + pinctrl_uart3_rtscts: uart3rtsctsgrp { + fsl,pins = < + MX51_PAD_KEY_COL4__UART3_RTS 0x1c5 + MX51_PAD_KEY_COL5__UART3_CTS 0x1c5 + >; + }; + + pinctrl_backlight_1: backlightgrp-1 { + fsl,pins = < + MX51_PAD_DI1_D1_CS__GPIO3_4 0x1f5 + >; + }; + + pinctrl_esdhc1_cd: esdhc1_cd { + fsl,pins = < + MX51_PAD_GPIO1_0__SD1_CD 0x20d5 + >; + }; + + pinctrl_gpiokeys_1: gpiokeysgrp-1 { + fsl,pins = < + MX51_PAD_NANDF_D9__GPIO3_31 0x1f5 + >; + }; + + pinctrl_gpioled: gpioledgrp-1 { + fsl,pins = < + MX51_PAD_NANDF_D10__GPIO3_30 0x80000000 + >; + }; + + pinctrl_reg_lcd_3v3: reg_lcd_3v3 { + fsl,pins = < + MX51_PAD_CSI1_D9__GPIO3_13 0x1f5 + >; + }; + }; +}; + +&ssi2 { + codec-handle = <&tlv320aic23>; + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + fsl,uart-has-rtscts; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3 &pinctrl_uart3_rtscts>; + fsl,uart-has-rtscts; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx51.dtsi b/arch/arm/boot/dts/imx51.dtsi index 28c96aada80b..5f8216d08f6b 100644 --- a/arch/arm/boot/dts/imx51.dtsi +++ b/arch/arm/boot/dts/imx51.dtsi @@ -12,6 +12,10 @@ #include "skeleton.dtsi" #include "imx51-pinfunc.h" +#include <dt-bindings/clock/imx5-clock.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> / { aliases { @@ -21,6 +25,10 @@ gpio3 = &gpio4; i2c0 = &i2c1; i2c1 = &i2c2; + mmc0 = &esdhc1; + mmc1 = &esdhc2; + mmc2 = &esdhc3; + mmc3 = &esdhc4; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; @@ -64,18 +72,32 @@ cpus { #address-cells = <1>; #size-cells = <0>; - cpu@0 { + cpu: cpu@0 { device_type = "cpu"; compatible = "arm,cortex-a8"; reg = <0>; - clock-latency = <61036>; /* two CLK32 periods */ - clocks = <&clks 24>; + clock-latency = <62500>; + clocks = <&clks IMX5_CLK_CPU_PODF>; clock-names = "cpu"; operating-points = < - /* kHz uV (No regulator support) */ - 160000 0 - 800000 0 + 166000 1000000 + 600000 1050000 + 800000 1100000 >; + voltage-tolerance = <5>; + }; + }; + + usbphy { + #address-cells = <1>; + #size-cells = <0>; + compatible = "simple-bus"; + + usbphy0: usbphy@0 { + compatible = "usb-nop-xceiv"; + reg = <0>; + clocks = <&clks IMX5_CLK_USB_PHY_GATE>; + clock-names = "main_clk"; }; }; @@ -102,7 +124,9 @@ compatible = "fsl,imx51-ipu"; reg = <0x40000000 0x20000000>; interrupts = <11 10>; - clocks = <&clks 59>, <&clks 110>, <&clks 61>; + clocks = <&clks IMX5_CLK_IPU_GATE>, + <&clks IMX5_CLK_IPU_DI0_GATE>, + <&clks IMX5_CLK_IPU_DI1_GATE>; clock-names = "bus", "di0", "di1"; resets = <&src 2>; @@ -139,7 +163,9 @@ compatible = "fsl,imx51-esdhc"; reg = <0x70004000 0x4000>; interrupts = <1>; - clocks = <&clks 44>, <&clks 0>, <&clks 71>; + clocks = <&clks IMX5_CLK_ESDHC1_IPG_GATE>, + <&clks IMX5_CLK_DUMMY>, + <&clks IMX5_CLK_ESDHC1_PER_GATE>; clock-names = "ipg", "ahb", "per"; status = "disabled"; }; @@ -148,7 +174,9 @@ compatible = "fsl,imx51-esdhc"; reg = <0x70008000 0x4000>; interrupts = <2>; - clocks = <&clks 45>, <&clks 0>, <&clks 72>; + clocks = <&clks IMX5_CLK_ESDHC2_IPG_GATE>, + <&clks IMX5_CLK_DUMMY>, + <&clks IMX5_CLK_ESDHC2_PER_GATE>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; status = "disabled"; @@ -158,7 +186,8 @@ compatible = "fsl,imx51-uart", "fsl,imx21-uart"; reg = <0x7000c000 0x4000>; interrupts = <33>; - clocks = <&clks 32>, <&clks 33>; + clocks = <&clks IMX5_CLK_UART3_IPG_GATE>, + <&clks IMX5_CLK_UART3_PER_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -169,7 +198,8 @@ compatible = "fsl,imx51-ecspi"; reg = <0x70010000 0x4000>; interrupts = <36>; - clocks = <&clks 51>, <&clks 52>; + clocks = <&clks IMX5_CLK_ECSPI1_IPG_GATE>, + <&clks IMX5_CLK_ECSPI1_PER_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -178,7 +208,7 @@ compatible = "fsl,imx51-ssi", "fsl,imx21-ssi"; reg = <0x70014000 0x4000>; interrupts = <30>; - clocks = <&clks 49>; + clocks = <&clks IMX5_CLK_SSI2_IPG_GATE>; dmas = <&sdma 24 1 0>, <&sdma 25 1 0>; dma-names = "rx", "tx"; @@ -191,7 +221,9 @@ compatible = "fsl,imx51-esdhc"; reg = <0x70020000 0x4000>; interrupts = <3>; - clocks = <&clks 46>, <&clks 0>, <&clks 73>; + clocks = <&clks IMX5_CLK_ESDHC3_IPG_GATE>, + <&clks IMX5_CLK_DUMMY>, + <&clks IMX5_CLK_ESDHC3_PER_GATE>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; status = "disabled"; @@ -201,25 +233,20 @@ compatible = "fsl,imx51-esdhc"; reg = <0x70024000 0x4000>; interrupts = <4>; - clocks = <&clks 47>, <&clks 0>, <&clks 74>; + clocks = <&clks IMX5_CLK_ESDHC4_IPG_GATE>, + <&clks IMX5_CLK_DUMMY>, + <&clks IMX5_CLK_ESDHC4_PER_GATE>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; status = "disabled"; }; }; - usbphy0: usbphy@0 { - compatible = "usb-nop-xceiv"; - clocks = <&clks 75>; - clock-names = "main_clk"; - status = "okay"; - }; - usbotg: usb@73f80000 { compatible = "fsl,imx51-usb", "fsl,imx27-usb"; reg = <0x73f80000 0x0200>; interrupts = <18>; - clocks = <&clks 108>; + clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 0>; fsl,usbphy = <&usbphy0>; status = "disabled"; @@ -229,7 +256,7 @@ compatible = "fsl,imx51-usb", "fsl,imx27-usb"; reg = <0x73f80200 0x0200>; interrupts = <14>; - clocks = <&clks 108>; + clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 1>; status = "disabled"; }; @@ -238,7 +265,7 @@ compatible = "fsl,imx51-usb", "fsl,imx27-usb"; reg = <0x73f80400 0x0200>; interrupts = <16>; - clocks = <&clks 108>; + clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 2>; status = "disabled"; }; @@ -247,7 +274,7 @@ compatible = "fsl,imx51-usb", "fsl,imx27-usb"; reg = <0x73f80600 0x0200>; interrupts = <17>; - clocks = <&clks 108>; + clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 3>; status = "disabled"; }; @@ -256,7 +283,7 @@ #index-cells = <1>; compatible = "fsl,imx51-usbmisc"; reg = <0x73f80800 0x200>; - clocks = <&clks 108>; + clocks = <&clks IMX5_CLK_USBOH3_GATE>; }; gpio1: gpio@73f84000 { @@ -303,7 +330,7 @@ compatible = "fsl,imx51-kpp", "fsl,imx21-kpp"; reg = <0x73f94000 0x4000>; interrupts = <60>; - clocks = <&clks 0>; + clocks = <&clks IMX5_CLK_DUMMY>; status = "disabled"; }; @@ -311,14 +338,14 @@ compatible = "fsl,imx51-wdt", "fsl,imx21-wdt"; reg = <0x73f98000 0x4000>; interrupts = <58>; - clocks = <&clks 0>; + clocks = <&clks IMX5_CLK_DUMMY>; }; wdog2: wdog@73f9c000 { compatible = "fsl,imx51-wdt", "fsl,imx21-wdt"; reg = <0x73f9c000 0x4000>; interrupts = <59>; - clocks = <&clks 0>; + clocks = <&clks IMX5_CLK_DUMMY>; status = "disabled"; }; @@ -326,7 +353,8 @@ compatible = "fsl,imx51-gpt", "fsl,imx31-gpt"; reg = <0x73fa0000 0x4000>; interrupts = <39>; - clocks = <&clks 36>, <&clks 41>; + clocks = <&clks IMX5_CLK_GPT_IPG_GATE>, + <&clks IMX5_CLK_GPT_HF_GATE>; clock-names = "ipg", "per"; }; @@ -339,7 +367,8 @@ #pwm-cells = <2>; compatible = "fsl,imx51-pwm", "fsl,imx27-pwm"; reg = <0x73fb4000 0x4000>; - clocks = <&clks 37>, <&clks 38>; + clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>, + <&clks IMX5_CLK_PWM1_HF_GATE>; clock-names = "ipg", "per"; interrupts = <61>; }; @@ -348,7 +377,8 @@ #pwm-cells = <2>; compatible = "fsl,imx51-pwm", "fsl,imx27-pwm"; reg = <0x73fb8000 0x4000>; - clocks = <&clks 39>, <&clks 40>; + clocks = <&clks IMX5_CLK_PWM2_IPG_GATE>, + <&clks IMX5_CLK_PWM2_HF_GATE>; clock-names = "ipg", "per"; interrupts = <94>; }; @@ -357,7 +387,8 @@ compatible = "fsl,imx51-uart", "fsl,imx21-uart"; reg = <0x73fbc000 0x4000>; interrupts = <31>; - clocks = <&clks 28>, <&clks 29>; + clocks = <&clks IMX5_CLK_UART1_IPG_GATE>, + <&clks IMX5_CLK_UART1_PER_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -366,7 +397,8 @@ compatible = "fsl,imx51-uart", "fsl,imx21-uart"; reg = <0x73fc0000 0x4000>; interrupts = <32>; - clocks = <&clks 30>, <&clks 31>; + clocks = <&clks IMX5_CLK_UART2_IPG_GATE>, + <&clks IMX5_CLK_UART2_PER_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -396,14 +428,14 @@ compatible = "fsl,imx51-iim", "fsl,imx27-iim"; reg = <0x83f98000 0x4000>; interrupts = <69>; - clocks = <&clks 107>; + clocks = <&clks IMX5_CLK_IIM_GATE>; }; owire: owire@83fa4000 { compatible = "fsl,imx51-owire", "fsl,imx21-owire"; reg = <0x83fa4000 0x4000>; interrupts = <88>; - clocks = <&clks 159>; + clocks = <&clks IMX5_CLK_OWIRE_GATE>; status = "disabled"; }; @@ -413,7 +445,8 @@ compatible = "fsl,imx51-ecspi"; reg = <0x83fac000 0x4000>; interrupts = <37>; - clocks = <&clks 53>, <&clks 54>; + clocks = <&clks IMX5_CLK_ECSPI2_IPG_GATE>, + <&clks IMX5_CLK_ECSPI2_PER_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -422,7 +455,8 @@ compatible = "fsl,imx51-sdma", "fsl,imx35-sdma"; reg = <0x83fb0000 0x4000>; interrupts = <6>; - clocks = <&clks 56>, <&clks 56>; + clocks = <&clks IMX5_CLK_SDMA_GATE>, + <&clks IMX5_CLK_SDMA_GATE>; clock-names = "ipg", "ahb"; #dma-cells = <3>; fsl,sdma-ram-script-name = "imx/sdma/sdma-imx51.bin"; @@ -434,7 +468,8 @@ compatible = "fsl,imx51-cspi", "fsl,imx35-cspi"; reg = <0x83fc0000 0x4000>; interrupts = <38>; - clocks = <&clks 55>, <&clks 55>; + clocks = <&clks IMX5_CLK_CSPI_IPG_GATE>, + <&clks IMX5_CLK_CSPI_IPG_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -445,7 +480,7 @@ compatible = "fsl,imx51-i2c", "fsl,imx21-i2c"; reg = <0x83fc4000 0x4000>; interrupts = <63>; - clocks = <&clks 35>; + clocks = <&clks IMX5_CLK_I2C2_GATE>; status = "disabled"; }; @@ -455,7 +490,7 @@ compatible = "fsl,imx51-i2c", "fsl,imx21-i2c"; reg = <0x83fc8000 0x4000>; interrupts = <62>; - clocks = <&clks 34>; + clocks = <&clks IMX5_CLK_I2C1_GATE>; status = "disabled"; }; @@ -463,7 +498,7 @@ compatible = "fsl,imx51-ssi", "fsl,imx21-ssi"; reg = <0x83fcc000 0x4000>; interrupts = <29>; - clocks = <&clks 48>; + clocks = <&clks IMX5_CLK_SSI1_IPG_GATE>; dmas = <&sdma 28 0 0>, <&sdma 29 0 0>; dma-names = "rx", "tx"; @@ -475,6 +510,8 @@ audmux: audmux@83fd0000 { compatible = "fsl,imx51-audmux", "fsl,imx31-audmux"; reg = <0x83fd0000 0x4000>; + clocks = <&clks IMX5_CLK_DUMMY>; + clock-names = "audmux"; status = "disabled"; }; @@ -483,7 +520,7 @@ #size-cells = <1>; compatible = "fsl,imx51-weim"; reg = <0x83fda000 0x1000>; - clocks = <&clks 57>; + clocks = <&clks IMX5_CLK_EMI_SLOW_GATE>; ranges = < 0 0 0xb0000000 0x08000000 1 0 0xb8000000 0x08000000 @@ -499,7 +536,7 @@ compatible = "fsl,imx51-nand"; reg = <0x83fdb000 0x1000 0xcfff0000 0x10000>; interrupts = <8>; - clocks = <&clks 60>; + clocks = <&clks IMX5_CLK_NFC_GATE>; status = "disabled"; }; @@ -507,7 +544,7 @@ compatible = "fsl,imx51-pata", "fsl,imx27-pata"; reg = <0x83fe0000 0x4000>; interrupts = <70>; - clocks = <&clks 172>; + clocks = <&clks IMX5_CLK_PATA_GATE>; status = "disabled"; }; @@ -515,7 +552,7 @@ compatible = "fsl,imx51-ssi", "fsl,imx21-ssi"; reg = <0x83fe8000 0x4000>; interrupts = <96>; - clocks = <&clks 50>; + clocks = <&clks IMX5_CLK_SSI3_IPG_GATE>; dmas = <&sdma 46 0 0>, <&sdma 47 0 0>; dma-names = "rx", "tx"; @@ -528,336 +565,12 @@ compatible = "fsl,imx51-fec", "fsl,imx27-fec"; reg = <0x83fec000 0x4000>; interrupts = <87>; - clocks = <&clks 42>, <&clks 42>, <&clks 42>; + clocks = <&clks IMX5_CLK_FEC_GATE>, + <&clks IMX5_CLK_FEC_GATE>, + <&clks IMX5_CLK_FEC_GATE>; clock-names = "ipg", "ahb", "ptp"; status = "disabled"; }; }; }; }; - -&iomuxc { - audmux { - pinctrl_audmux_1: audmuxgrp-1 { - fsl,pins = < - MX51_PAD_AUD3_BB_TXD__AUD3_TXD 0x80000000 - MX51_PAD_AUD3_BB_RXD__AUD3_RXD 0x80000000 - MX51_PAD_AUD3_BB_CK__AUD3_TXC 0x80000000 - MX51_PAD_AUD3_BB_FS__AUD3_TXFS 0x80000000 - >; - }; - }; - - fec { - pinctrl_fec_1: fecgrp-1 { - fsl,pins = < - MX51_PAD_EIM_EB2__FEC_MDIO 0x80000000 - MX51_PAD_EIM_EB3__FEC_RDATA1 0x80000000 - MX51_PAD_EIM_CS2__FEC_RDATA2 0x80000000 - MX51_PAD_EIM_CS3__FEC_RDATA3 0x80000000 - MX51_PAD_EIM_CS4__FEC_RX_ER 0x80000000 - MX51_PAD_EIM_CS5__FEC_CRS 0x80000000 - MX51_PAD_NANDF_RB2__FEC_COL 0x80000000 - MX51_PAD_NANDF_RB3__FEC_RX_CLK 0x80000000 - MX51_PAD_NANDF_D9__FEC_RDATA0 0x80000000 - MX51_PAD_NANDF_D8__FEC_TDATA0 0x80000000 - MX51_PAD_NANDF_CS2__FEC_TX_ER 0x80000000 - MX51_PAD_NANDF_CS3__FEC_MDC 0x80000000 - MX51_PAD_NANDF_CS4__FEC_TDATA1 0x80000000 - MX51_PAD_NANDF_CS5__FEC_TDATA2 0x80000000 - MX51_PAD_NANDF_CS6__FEC_TDATA3 0x80000000 - MX51_PAD_NANDF_CS7__FEC_TX_EN 0x80000000 - MX51_PAD_NANDF_RDY_INT__FEC_TX_CLK 0x80000000 - >; - }; - - pinctrl_fec_2: fecgrp-2 { - fsl,pins = < - MX51_PAD_DI_GP3__FEC_TX_ER 0x80000000 - MX51_PAD_DI2_PIN4__FEC_CRS 0x80000000 - MX51_PAD_DI2_PIN2__FEC_MDC 0x80000000 - MX51_PAD_DI2_PIN3__FEC_MDIO 0x80000000 - MX51_PAD_DI2_DISP_CLK__FEC_RDATA1 0x80000000 - MX51_PAD_DI_GP4__FEC_RDATA2 0x80000000 - MX51_PAD_DISP2_DAT0__FEC_RDATA3 0x80000000 - MX51_PAD_DISP2_DAT1__FEC_RX_ER 0x80000000 - MX51_PAD_DISP2_DAT6__FEC_TDATA1 0x80000000 - MX51_PAD_DISP2_DAT7__FEC_TDATA2 0x80000000 - MX51_PAD_DISP2_DAT8__FEC_TDATA3 0x80000000 - MX51_PAD_DISP2_DAT9__FEC_TX_EN 0x80000000 - MX51_PAD_DISP2_DAT10__FEC_COL 0x80000000 - MX51_PAD_DISP2_DAT11__FEC_RX_CLK 0x80000000 - MX51_PAD_DISP2_DAT12__FEC_RX_DV 0x80000000 - MX51_PAD_DISP2_DAT13__FEC_TX_CLK 0x80000000 - MX51_PAD_DISP2_DAT14__FEC_RDATA0 0x80000000 - MX51_PAD_DISP2_DAT15__FEC_TDATA0 0x80000000 - >; - }; - }; - - ecspi1 { - pinctrl_ecspi1_1: ecspi1grp-1 { - fsl,pins = < - MX51_PAD_CSPI1_MISO__ECSPI1_MISO 0x185 - MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI 0x185 - MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK 0x185 - >; - }; - }; - - ecspi2 { - pinctrl_ecspi2_1: ecspi2grp-1 { - fsl,pins = < - MX51_PAD_NANDF_RB3__ECSPI2_MISO 0x185 - MX51_PAD_NANDF_D15__ECSPI2_MOSI 0x185 - MX51_PAD_NANDF_RB2__ECSPI2_SCLK 0x185 - >; - }; - }; - - esdhc1 { - pinctrl_esdhc1_1: esdhc1grp-1 { - fsl,pins = < - MX51_PAD_SD1_CMD__SD1_CMD 0x400020d5 - MX51_PAD_SD1_CLK__SD1_CLK 0x20d5 - MX51_PAD_SD1_DATA0__SD1_DATA0 0x20d5 - MX51_PAD_SD1_DATA1__SD1_DATA1 0x20d5 - MX51_PAD_SD1_DATA2__SD1_DATA2 0x20d5 - MX51_PAD_SD1_DATA3__SD1_DATA3 0x20d5 - >; - }; - }; - - esdhc2 { - pinctrl_esdhc2_1: esdhc2grp-1 { - fsl,pins = < - MX51_PAD_SD2_CMD__SD2_CMD 0x400020d5 - MX51_PAD_SD2_CLK__SD2_CLK 0x20d5 - MX51_PAD_SD2_DATA0__SD2_DATA0 0x20d5 - MX51_PAD_SD2_DATA1__SD2_DATA1 0x20d5 - MX51_PAD_SD2_DATA2__SD2_DATA2 0x20d5 - MX51_PAD_SD2_DATA3__SD2_DATA3 0x20d5 - >; - }; - }; - - i2c2 { - pinctrl_i2c2_1: i2c2grp-1 { - fsl,pins = < - MX51_PAD_KEY_COL4__I2C2_SCL 0x400001ed - MX51_PAD_KEY_COL5__I2C2_SDA 0x400001ed - >; - }; - - pinctrl_i2c2_2: i2c2grp-2 { - fsl,pins = < - MX51_PAD_EIM_D27__I2C2_SCL 0x400001ed - MX51_PAD_EIM_D24__I2C2_SDA 0x400001ed - >; - }; - - pinctrl_i2c2_3: i2c2grp-3 { - fsl,pins = < - MX51_PAD_GPIO1_2__I2C2_SCL 0x400001ed - MX51_PAD_GPIO1_3__I2C2_SDA 0x400001ed - >; - }; - }; - - ipu_disp1 { - pinctrl_ipu_disp1_1: ipudisp1grp-1 { - fsl,pins = < - MX51_PAD_DISP1_DAT0__DISP1_DAT0 0x5 - MX51_PAD_DISP1_DAT1__DISP1_DAT1 0x5 - MX51_PAD_DISP1_DAT2__DISP1_DAT2 0x5 - MX51_PAD_DISP1_DAT3__DISP1_DAT3 0x5 - MX51_PAD_DISP1_DAT4__DISP1_DAT4 0x5 - MX51_PAD_DISP1_DAT5__DISP1_DAT5 0x5 - MX51_PAD_DISP1_DAT6__DISP1_DAT6 0x5 - MX51_PAD_DISP1_DAT7__DISP1_DAT7 0x5 - MX51_PAD_DISP1_DAT8__DISP1_DAT8 0x5 - MX51_PAD_DISP1_DAT9__DISP1_DAT9 0x5 - MX51_PAD_DISP1_DAT10__DISP1_DAT10 0x5 - MX51_PAD_DISP1_DAT11__DISP1_DAT11 0x5 - MX51_PAD_DISP1_DAT12__DISP1_DAT12 0x5 - MX51_PAD_DISP1_DAT13__DISP1_DAT13 0x5 - MX51_PAD_DISP1_DAT14__DISP1_DAT14 0x5 - MX51_PAD_DISP1_DAT15__DISP1_DAT15 0x5 - MX51_PAD_DISP1_DAT16__DISP1_DAT16 0x5 - MX51_PAD_DISP1_DAT17__DISP1_DAT17 0x5 - MX51_PAD_DISP1_DAT18__DISP1_DAT18 0x5 - MX51_PAD_DISP1_DAT19__DISP1_DAT19 0x5 - MX51_PAD_DISP1_DAT20__DISP1_DAT20 0x5 - MX51_PAD_DISP1_DAT21__DISP1_DAT21 0x5 - MX51_PAD_DISP1_DAT22__DISP1_DAT22 0x5 - MX51_PAD_DISP1_DAT23__DISP1_DAT23 0x5 - MX51_PAD_DI1_PIN2__DI1_PIN2 0x5 /* hsync */ - MX51_PAD_DI1_PIN3__DI1_PIN3 0x5 /* vsync */ - >; - }; - }; - - ipu_disp2 { - pinctrl_ipu_disp2_1: ipudisp2grp-1 { - fsl,pins = < - MX51_PAD_DISP2_DAT0__DISP2_DAT0 0x5 - MX51_PAD_DISP2_DAT1__DISP2_DAT1 0x5 - MX51_PAD_DISP2_DAT2__DISP2_DAT2 0x5 - MX51_PAD_DISP2_DAT3__DISP2_DAT3 0x5 - MX51_PAD_DISP2_DAT4__DISP2_DAT4 0x5 - MX51_PAD_DISP2_DAT5__DISP2_DAT5 0x5 - MX51_PAD_DISP2_DAT6__DISP2_DAT6 0x5 - MX51_PAD_DISP2_DAT7__DISP2_DAT7 0x5 - MX51_PAD_DISP2_DAT8__DISP2_DAT8 0x5 - MX51_PAD_DISP2_DAT9__DISP2_DAT9 0x5 - MX51_PAD_DISP2_DAT10__DISP2_DAT10 0x5 - MX51_PAD_DISP2_DAT11__DISP2_DAT11 0x5 - MX51_PAD_DISP2_DAT12__DISP2_DAT12 0x5 - MX51_PAD_DISP2_DAT13__DISP2_DAT13 0x5 - MX51_PAD_DISP2_DAT14__DISP2_DAT14 0x5 - MX51_PAD_DISP2_DAT15__DISP2_DAT15 0x5 - MX51_PAD_DI2_PIN2__DI2_PIN2 0x5 /* hsync */ - MX51_PAD_DI2_PIN3__DI2_PIN3 0x5 /* vsync */ - MX51_PAD_DI2_DISP_CLK__DI2_DISP_CLK 0x5 /* CLK */ - MX51_PAD_DI_GP4__DI2_PIN15 0x5 /* DE */ - >; - }; - }; - - kpp { - pinctrl_kpp_1: kppgrp-1 { - fsl,pins = < - MX51_PAD_KEY_ROW0__KEY_ROW0 0xe0 - MX51_PAD_KEY_ROW1__KEY_ROW1 0xe0 - MX51_PAD_KEY_ROW2__KEY_ROW2 0xe0 - MX51_PAD_KEY_ROW3__KEY_ROW3 0xe0 - MX51_PAD_KEY_COL0__KEY_COL0 0xe8 - MX51_PAD_KEY_COL1__KEY_COL1 0xe8 - MX51_PAD_KEY_COL2__KEY_COL2 0xe8 - MX51_PAD_KEY_COL3__KEY_COL3 0xe8 - >; - }; - }; - - pata { - pinctrl_pata_1: patagrp-1 { - fsl,pins = < - MX51_PAD_NANDF_WE_B__PATA_DIOW 0x2004 - MX51_PAD_NANDF_RE_B__PATA_DIOR 0x2004 - MX51_PAD_NANDF_ALE__PATA_BUFFER_EN 0x2004 - MX51_PAD_NANDF_CLE__PATA_RESET_B 0x2004 - MX51_PAD_NANDF_WP_B__PATA_DMACK 0x2004 - MX51_PAD_NANDF_RB0__PATA_DMARQ 0x2004 - MX51_PAD_NANDF_RB1__PATA_IORDY 0x2004 - MX51_PAD_GPIO_NAND__PATA_INTRQ 0x2004 - MX51_PAD_NANDF_CS2__PATA_CS_0 0x2004 - MX51_PAD_NANDF_CS3__PATA_CS_1 0x2004 - MX51_PAD_NANDF_CS4__PATA_DA_0 0x2004 - MX51_PAD_NANDF_CS5__PATA_DA_1 0x2004 - MX51_PAD_NANDF_CS6__PATA_DA_2 0x2004 - MX51_PAD_NANDF_D15__PATA_DATA15 0x2004 - MX51_PAD_NANDF_D14__PATA_DATA14 0x2004 - MX51_PAD_NANDF_D13__PATA_DATA13 0x2004 - MX51_PAD_NANDF_D12__PATA_DATA12 0x2004 - MX51_PAD_NANDF_D11__PATA_DATA11 0x2004 - MX51_PAD_NANDF_D10__PATA_DATA10 0x2004 - MX51_PAD_NANDF_D9__PATA_DATA9 0x2004 - MX51_PAD_NANDF_D8__PATA_DATA8 0x2004 - MX51_PAD_NANDF_D7__PATA_DATA7 0x2004 - MX51_PAD_NANDF_D6__PATA_DATA6 0x2004 - MX51_PAD_NANDF_D5__PATA_DATA5 0x2004 - MX51_PAD_NANDF_D4__PATA_DATA4 0x2004 - MX51_PAD_NANDF_D3__PATA_DATA3 0x2004 - MX51_PAD_NANDF_D2__PATA_DATA2 0x2004 - MX51_PAD_NANDF_D1__PATA_DATA1 0x2004 - MX51_PAD_NANDF_D0__PATA_DATA0 0x2004 - >; - }; - }; - - uart1 { - pinctrl_uart1_1: uart1grp-1 { - fsl,pins = < - MX51_PAD_UART1_RXD__UART1_RXD 0x1c5 - MX51_PAD_UART1_TXD__UART1_TXD 0x1c5 - >; - }; - - pinctrl_uart1_rtscts_1: uart1rtscts-1 { - fsl,pins = < - MX51_PAD_UART1_RTS__UART1_RTS 0x1c5 - MX51_PAD_UART1_CTS__UART1_CTS 0x1c5 - >; - }; - }; - - uart2 { - pinctrl_uart2_1: uart2grp-1 { - fsl,pins = < - MX51_PAD_UART2_RXD__UART2_RXD 0x1c5 - MX51_PAD_UART2_TXD__UART2_TXD 0x1c5 - >; - }; - }; - - uart3 { - pinctrl_uart3_1: uart3grp-1 { - fsl,pins = < - MX51_PAD_EIM_D25__UART3_RXD 0x1c5 - MX51_PAD_EIM_D26__UART3_TXD 0x1c5 - >; - }; - - pinctrl_uart3_rtscts_1: uart3rtscts-1 { - fsl,pins = < - MX51_PAD_EIM_D27__UART3_RTS 0x1c5 - MX51_PAD_EIM_D24__UART3_CTS 0x1c5 - >; - }; - - pinctrl_uart3_2: uart3grp-2 { - fsl,pins = < - MX51_PAD_UART3_RXD__UART3_RXD 0x1c5 - MX51_PAD_UART3_TXD__UART3_TXD 0x1c5 - >; - }; - }; - - usbh1 { - pinctrl_usbh1_1: usbh1grp-1 { - fsl,pins = < - MX51_PAD_USBH1_DATA0__USBH1_DATA0 0x1e5 - MX51_PAD_USBH1_DATA1__USBH1_DATA1 0x1e5 - MX51_PAD_USBH1_DATA2__USBH1_DATA2 0x1e5 - MX51_PAD_USBH1_DATA3__USBH1_DATA3 0x1e5 - MX51_PAD_USBH1_DATA4__USBH1_DATA4 0x1e5 - MX51_PAD_USBH1_DATA5__USBH1_DATA5 0x1e5 - MX51_PAD_USBH1_DATA6__USBH1_DATA6 0x1e5 - MX51_PAD_USBH1_DATA7__USBH1_DATA7 0x1e5 - MX51_PAD_USBH1_CLK__USBH1_CLK 0x1e5 - MX51_PAD_USBH1_DIR__USBH1_DIR 0x1e5 - MX51_PAD_USBH1_NXT__USBH1_NXT 0x1e5 - MX51_PAD_USBH1_STP__USBH1_STP 0x1e5 - >; - }; - }; - - usbh2 { - pinctrl_usbh2_1: usbh2grp-1 { - fsl,pins = < - MX51_PAD_EIM_D16__USBH2_DATA0 0x1e5 - MX51_PAD_EIM_D17__USBH2_DATA1 0x1e5 - MX51_PAD_EIM_D18__USBH2_DATA2 0x1e5 - MX51_PAD_EIM_D19__USBH2_DATA3 0x1e5 - MX51_PAD_EIM_D20__USBH2_DATA4 0x1e5 - MX51_PAD_EIM_D21__USBH2_DATA5 0x1e5 - MX51_PAD_EIM_D22__USBH2_DATA6 0x1e5 - MX51_PAD_EIM_D23__USBH2_DATA7 0x1e5 - MX51_PAD_EIM_A24__USBH2_CLK 0x1e5 - MX51_PAD_EIM_A25__USBH2_DIR 0x1e5 - MX51_PAD_EIM_A27__USBH2_NXT 0x1e5 - MX51_PAD_EIM_A26__USBH2_STP 0x1e5 - >; - }; - }; -}; diff --git a/arch/arm/boot/dts/imx53-ard.dts b/arch/arm/boot/dts/imx53-ard.dts index 174f86938c89..e9337ad52f59 100644 --- a/arch/arm/boot/dts/imx53-ard.dts +++ b/arch/arm/boot/dts/imx53-ard.dts @@ -49,9 +49,12 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_3p3v: 3p3v { + reg_3p3v: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "3P3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; @@ -99,7 +102,7 @@ &esdhc1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc1_2>; + pinctrl-0 = <&pinctrl_esdhc1>; cd-gpios = <&gpio1 1 0>; wp-gpios = <&gpio1 9 0>; status = "okay"; @@ -109,7 +112,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; - hog { + imx53-ard { pinctrl_hog: hoggrp { fsl,pins = < MX53_PAD_GPIO_1__GPIO1_1 0x80000000 @@ -148,11 +151,33 @@ MX53_PAD_EIM_CS1__EMI_WEIM_CS_1 0x80000000 >; }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5 + MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5 + MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5 + MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5 + MX53_PAD_PATA_DATA8__ESDHC1_DAT4 0x1d5 + MX53_PAD_PATA_DATA9__ESDHC1_DAT5 0x1d5 + MX53_PAD_PATA_DATA10__ESDHC1_DAT6 0x1d5 + MX53_PAD_PATA_DATA11__ESDHC1_DAT7 0x1d5 + MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5 + MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4 + MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4 + >; + }; }; }; &uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_2>; + pinctrl-0 = <&pinctrl_uart1>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx53-evk.dts b/arch/arm/boot/dts/imx53-evk.dts deleted file mode 100644 index 801fda728ed6..000000000000 --- a/arch/arm/boot/dts/imx53-evk.dts +++ /dev/null @@ -1,126 +0,0 @@ -/* - * Copyright 2011 Freescale Semiconductor, Inc. - * Copyright 2011 Linaro Ltd. - * - * The code contained herein is licensed under the GNU General Public - * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: - * - * http://www.opensource.org/licenses/gpl-license.html - * http://www.gnu.org/copyleft/gpl.html - */ - -/dts-v1/; -#include "imx53.dtsi" - -/ { - model = "Freescale i.MX53 Evaluation Kit"; - compatible = "fsl,imx53-evk", "fsl,imx53"; - - memory { - reg = <0x70000000 0x80000000>; - }; - - leds { - compatible = "gpio-leds"; - - green { - label = "Heartbeat"; - gpios = <&gpio7 7 0>; - linux,default-trigger = "heartbeat"; - }; - }; -}; - -&esdhc1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc1_1>; - cd-gpios = <&gpio3 13 0>; - wp-gpios = <&gpio3 14 0>; - status = "okay"; -}; - -&ecspi1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi1_1>; - fsl,spi-num-chipselects = <2>; - cs-gpios = <&gpio2 30 0>, <&gpio3 19 0>; - status = "okay"; - - flash: at45db321d@1 { - #address-cells = <1>; - #size-cells = <1>; - compatible = "atmel,at45db321d", "atmel,at45", "atmel,dataflash"; - spi-max-frequency = <25000000>; - reg = <1>; - - partition@0 { - label = "U-Boot"; - reg = <0x0 0x40000>; - read-only; - }; - - partition@40000 { - label = "Kernel"; - reg = <0x40000 0x3c0000>; - }; - }; -}; - -&esdhc3 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc3_1>; - cd-gpios = <&gpio3 11 0>; - wp-gpios = <&gpio3 12 0>; - status = "okay"; -}; - -&iomuxc { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_hog>; - - hog { - pinctrl_hog: hoggrp { - fsl,pins = < - MX53_PAD_EIM_EB2__GPIO2_30 0x80000000 - MX53_PAD_EIM_D19__GPIO3_19 0x80000000 - MX53_PAD_EIM_DA11__GPIO3_11 0x80000000 - MX53_PAD_EIM_DA12__GPIO3_12 0x80000000 - MX53_PAD_EIM_DA13__GPIO3_13 0x80000000 - MX53_PAD_EIM_DA14__GPIO3_14 0x80000000 - MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000 - MX53_PAD_PATA_DA_1__GPIO7_7 0x80000000 - >; - }; - }; -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_1>; - status = "okay"; -}; - -&i2c2 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2_1>; - status = "okay"; - - pmic: mc13892@08 { - compatible = "fsl,mc13892", "fsl,mc13xxx"; - reg = <0x08>; - }; - - codec: sgtl5000@0a { - compatible = "fsl,sgtl5000"; - reg = <0x0a>; - }; -}; - -&fec { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec_1>; - phy-mode = "rmii"; - phy-reset-gpios = <&gpio7 6 0>; - status = "okay"; -}; diff --git a/arch/arm/boot/dts/imx53-m53evk.dts b/arch/arm/boot/dts/imx53-m53evk.dts index 0298adc73bb7..f6d3ac3e5587 100644 --- a/arch/arm/boot/dts/imx53-m53evk.dts +++ b/arch/arm/boot/dts/imx53-m53evk.dts @@ -25,7 +25,7 @@ compatible = "fsl,imx-parallel-display"; interface-pix-fmt = "bgr666"; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ipu_disp2_1>; + pinctrl-0 = <&pinctrl_ipu_disp1>; display-timings { 800x480p60 { @@ -56,6 +56,7 @@ pwms = <&pwm1 0 3000>; brightness-levels = <0 4 8 16 32 64 128 255>; default-brightness-level = <6>; + power-supply = <®_backlight>; }; leds { @@ -78,14 +79,36 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_3p2v: 3p2v { + reg_3p2v: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "3P2V"; regulator-min-microvolt = <3200000>; regulator-max-microvolt = <3200000>; regulator-always-on; }; + + + reg_backlight: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "lcd-supply"; + regulator-min-microvolt = <3200000>; + regulator-max-microvolt = <3200000>; + regulator-always-on; + }; + + reg_usbh1_vbus: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 2 0>; + }; }; sound { @@ -107,25 +130,25 @@ &audmux { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_audmux_2>; + pinctrl-0 = <&pinctrl_audmux>; status = "okay"; }; &can1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_can1_3>; + pinctrl-0 = <&pinctrl_can1>; status = "okay"; }; &can2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_can2_1>; + pinctrl-0 = <&pinctrl_can2>; status = "okay"; }; &esdhc1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc1_1>; + pinctrl-0 = <&pinctrl_esdhc1>; cd-gpios = <&gpio1 1 0>; wp-gpios = <&gpio1 9 0>; status = "okay"; @@ -133,14 +156,14 @@ &fec { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec_1>; + pinctrl-0 = <&pinctrl_fec>; phy-mode = "rmii"; status = "okay"; }; &i2c1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1_2>; + pinctrl-0 = <&pinctrl_i2c1>; status = "okay"; sgtl5000: codec@0a { @@ -148,13 +171,13 @@ reg = <0x0a>; VDDA-supply = <®_3p2v>; VDDIO-supply = <®_3p2v>; - clocks = <&clks 150>; + clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>; }; }; &i2c2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2_2>; + pinctrl-0 = <&pinctrl_i2c2>; clock-frequency = <400000>; status = "okay"; @@ -198,7 +221,7 @@ &i2c3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c3_1>; + pinctrl-0 = <&pinctrl_i2c3>; status = "okay"; }; @@ -206,14 +229,14 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; - hog { + imx53-m53evk { pinctrl_hog: hoggrp { fsl,pins = < MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000 MX53_PAD_EIM_EB3__GPIO2_31 0x80000000 MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000 - MX53_PAD_DISP0_DAT8__PWM1_PWMO 0x5 - + MX53_PAD_GPIO_2__GPIO1_2 0x80000000 + MX53_PAD_GPIO_3__USBOH3_USBH1_OC 0x80000000 >; }; @@ -223,6 +246,162 @@ MX53_PAD_PATA_DATA9__GPIO2_9 0x80000000 >; }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX53_PAD_SD2_DATA3__AUDMUX_AUD4_TXC 0x80000000 + MX53_PAD_SD2_DATA2__AUDMUX_AUD4_TXD 0x80000000 + MX53_PAD_SD2_DATA1__AUDMUX_AUD4_TXFS 0x80000000 + MX53_PAD_SD2_DATA0__AUDMUX_AUD4_RXD 0x80000000 + >; + }; + + pinctrl_can1: can1grp { + fsl,pins = < + MX53_PAD_GPIO_7__CAN1_TXCAN 0x80000000 + MX53_PAD_GPIO_8__CAN1_RXCAN 0x80000000 + >; + }; + + pinctrl_can2: can2grp { + fsl,pins = < + MX53_PAD_KEY_COL4__CAN2_TXCAN 0x80000000 + MX53_PAD_KEY_ROW4__CAN2_RXCAN 0x80000000 + >; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5 + MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5 + MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5 + MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5 + MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5 + MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX53_PAD_FEC_MDC__FEC_MDC 0x80000000 + MX53_PAD_FEC_MDIO__FEC_MDIO 0x80000000 + MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x80000000 + MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x80000000 + MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x80000000 + MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x80000000 + MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x80000000 + MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000 + MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x80000000 + MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x80000000 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX53_PAD_EIM_D21__I2C1_SCL 0xc0000000 + MX53_PAD_EIM_D28__I2C1_SDA 0xc0000000 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX53_PAD_EIM_D16__I2C2_SDA 0xc0000000 + MX53_PAD_EIM_EB2__I2C2_SCL 0xc0000000 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX53_PAD_GPIO_6__I2C3_SDA 0xc0000000 + MX53_PAD_GPIO_5__I2C3_SCL 0xc0000000 + >; + }; + + pinctrl_ipu_disp1: ipudisp1grp { + fsl,pins = < + MX53_PAD_EIM_DA9__IPU_DISP1_DAT_0 0x5 + MX53_PAD_EIM_DA8__IPU_DISP1_DAT_1 0x5 + MX53_PAD_EIM_DA7__IPU_DISP1_DAT_2 0x5 + MX53_PAD_EIM_DA6__IPU_DISP1_DAT_3 0x5 + MX53_PAD_EIM_DA5__IPU_DISP1_DAT_4 0x5 + MX53_PAD_EIM_DA4__IPU_DISP1_DAT_5 0x5 + MX53_PAD_EIM_DA3__IPU_DISP1_DAT_6 0x5 + MX53_PAD_EIM_DA2__IPU_DISP1_DAT_7 0x5 + MX53_PAD_EIM_DA1__IPU_DISP1_DAT_8 0x5 + MX53_PAD_EIM_DA0__IPU_DISP1_DAT_9 0x5 + MX53_PAD_EIM_EB1__IPU_DISP1_DAT_10 0x5 + MX53_PAD_EIM_EB0__IPU_DISP1_DAT_11 0x5 + MX53_PAD_EIM_A17__IPU_DISP1_DAT_12 0x5 + MX53_PAD_EIM_A18__IPU_DISP1_DAT_13 0x5 + MX53_PAD_EIM_A19__IPU_DISP1_DAT_14 0x5 + MX53_PAD_EIM_A20__IPU_DISP1_DAT_15 0x5 + MX53_PAD_EIM_A21__IPU_DISP1_DAT_16 0x5 + MX53_PAD_EIM_A22__IPU_DISP1_DAT_17 0x5 + MX53_PAD_EIM_A23__IPU_DISP1_DAT_18 0x5 + MX53_PAD_EIM_A24__IPU_DISP1_DAT_19 0x5 + MX53_PAD_EIM_D31__IPU_DISP1_DAT_20 0x5 + MX53_PAD_EIM_D30__IPU_DISP1_DAT_21 0x5 + MX53_PAD_EIM_D26__IPU_DISP1_DAT_22 0x5 + MX53_PAD_EIM_D27__IPU_DISP1_DAT_23 0x5 + MX53_PAD_EIM_A16__IPU_DI1_DISP_CLK 0x5 + MX53_PAD_EIM_DA13__IPU_DI1_D0_CS 0x5 + MX53_PAD_EIM_DA14__IPU_DI1_D1_CS 0x5 + MX53_PAD_EIM_DA15__IPU_DI1_PIN1 0x5 + MX53_PAD_EIM_DA11__IPU_DI1_PIN2 0x5 + MX53_PAD_EIM_DA12__IPU_DI1_PIN3 0x5 + MX53_PAD_EIM_A25__IPU_DI1_PIN12 0x5 + MX53_PAD_EIM_DA10__IPU_DI1_PIN15 0x5 + >; + }; + + pinctrl_nand: nandgrp { + fsl,pins = < + MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B 0x4 + MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B 0x4 + MX53_PAD_NANDF_CLE__EMI_NANDF_CLE 0x4 + MX53_PAD_NANDF_ALE__EMI_NANDF_ALE 0x4 + MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B 0xe0 + MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0 0xe0 + MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0 0x4 + MX53_PAD_PATA_DATA0__EMI_NANDF_D_0 0xa4 + MX53_PAD_PATA_DATA1__EMI_NANDF_D_1 0xa4 + MX53_PAD_PATA_DATA2__EMI_NANDF_D_2 0xa4 + MX53_PAD_PATA_DATA3__EMI_NANDF_D_3 0xa4 + MX53_PAD_PATA_DATA4__EMI_NANDF_D_4 0xa4 + MX53_PAD_PATA_DATA5__EMI_NANDF_D_5 0xa4 + MX53_PAD_PATA_DATA6__EMI_NANDF_D_6 0xa4 + MX53_PAD_PATA_DATA7__EMI_NANDF_D_7 0xa4 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX53_PAD_DISP0_DAT8__PWM1_PWMO 0x5 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4 + MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4 + MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4 + MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4 + MX53_PAD_PATA_DA_1__UART3_CTS 0x1e4 + MX53_PAD_PATA_DA_2__UART3_RTS 0x1e4 + >; + }; }; }; @@ -232,7 +411,7 @@ &nfc { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_nand_1>; + pinctrl-0 = <&pinctrl_nand>; nand-bus-width = <8>; nand-ecc-mode = "hw"; status = "okay"; @@ -240,7 +419,11 @@ &pwm1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_pwm1_1>; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&sata { status = "okay"; }; @@ -251,18 +434,29 @@ &uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_2>; + pinctrl-0 = <&pinctrl_uart1>; status = "okay"; }; &uart2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2_1>; + pinctrl-0 = <&pinctrl_uart2>; status = "okay"; }; &uart3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart3_1>; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usbh1_vbus>; + phy_type = "utmi"; + status = "okay"; +}; + +&usbotg { + dr_mode = "peripheral"; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx53-mba53.dts b/arch/arm/boot/dts/imx53-mba53.dts index a5b55c603591..7c8c12969892 100644 --- a/arch/arm/boot/dts/imx53-mba53.dts +++ b/arch/arm/boot/dts/imx53-mba53.dts @@ -17,14 +17,6 @@ model = "TQ MBa53 starter kit"; compatible = "tq,mba53", "tq,tqma53", "fsl,imx53"; - reg_backlight: fixed@0 { - compatible = "regulator-fixed"; - regulator-name = "lcd-supply"; - gpio = <&gpio2 5 0>; - startup-delay-us = <5000>; - enable-active-low; - }; - backlight { compatible = "pwm-backlight"; pwms = <&pwm2 0 50000>; @@ -48,12 +40,27 @@ }; }; - reg_3p2v: 3p2v { - compatible = "regulator-fixed"; - regulator-name = "3P2V"; - regulator-min-microvolt = <3200000>; - regulator-max-microvolt = <3200000>; - regulator-always-on; + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_backlight: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "lcd-supply"; + gpio = <&gpio2 5 0>; + startup-delay-us = <5000>; + }; + + reg_3p2v: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "3P2V"; + regulator-min-microvolt = <3200000>; + regulator-max-microvolt = <3200000>; + regulator-always-on; + }; }; sound { @@ -157,14 +164,14 @@ &audmux { status = "okay"; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_audmux_1>; + pinctrl-0 = <&pinctrl_audmux>; }; &i2c2 { codec: sgtl5000@a { compatible = "fsl,sgtl5000"; reg = <0x0a>; - clocks = <&clks 150>; + clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>; VDDA-supply = <®_3p2v>; VDDIO-supply = <®_3p2v>; }; diff --git a/arch/arm/boot/dts/imx53-qsb-common.dtsi b/arch/arm/boot/dts/imx53-qsb-common.dtsi new file mode 100644 index 000000000000..3f825a6813da --- /dev/null +++ b/arch/arm/boot/dts/imx53-qsb-common.dtsi @@ -0,0 +1,345 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include "imx53.dtsi" + +/ { + memory { + reg = <0x70000000 0x40000000>; + }; + + display0: display@di0 { + compatible = "fsl,imx-parallel-display"; + interface-pix-fmt = "rgb565"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ipu_disp0>; + status = "disabled"; + display-timings { + claawvga { + native-mode; + clock-frequency = <27000000>; + hactive = <800>; + vactive = <480>; + hback-porch = <40>; + hfront-porch = <60>; + vback-porch = <10>; + vfront-porch = <10>; + hsync-len = <20>; + vsync-len = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + + port { + display0_in: endpoint { + remote-endpoint = <&ipu_di0_disp0>; + }; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + power { + label = "Power Button"; + gpios = <&gpio1 8 0>; + linux,code = <116>; /* KEY_POWER */ + }; + + volume-up { + label = "Volume Up"; + gpios = <&gpio2 14 0>; + linux,code = <115>; /* KEY_VOLUMEUP */ + gpio-key,wakeup; + }; + + volume-down { + label = "Volume Down"; + gpios = <&gpio2 15 0>; + linux,code = <114>; /* KEY_VOLUMEDOWN */ + gpio-key,wakeup; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pin_gpio7_7>; + + user { + label = "Heartbeat"; + gpios = <&gpio7 7 0>; + linux,default-trigger = "heartbeat"; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_3p2v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "3P2V"; + regulator-min-microvolt = <3200000>; + regulator-max-microvolt = <3200000>; + regulator-always-on; + }; + + reg_usb_vbus: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "usb_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio7 8 0>; + enable-active-high; + }; + }; + + sound { + compatible = "fsl,imx53-qsb-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "imx53-qsb-sgtl5000"; + ssi-controller = <&ssi2>; + audio-codec = <&sgtl5000>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-int-port = <2>; + mux-ext-port = <5>; + }; +}; + +&esdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc1>; + status = "okay"; +}; + +&ipu_di0_disp0 { + remote-endpoint = <&display0_in>; +}; + +&ssi2 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&esdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc3>; + cd-gpios = <&gpio3 11 0>; + wp-gpios = <&gpio3 12 0>; + bus-width = <8>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx53-qsb { + pinctrl_hog: hoggrp { + fsl,pins = < + MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000 + MX53_PAD_GPIO_8__GPIO1_8 0x80000000 + MX53_PAD_PATA_DATA14__GPIO2_14 0x80000000 + MX53_PAD_PATA_DATA15__GPIO2_15 0x80000000 + MX53_PAD_EIM_DA11__GPIO3_11 0x80000000 + MX53_PAD_EIM_DA12__GPIO3_12 0x80000000 + MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000 + MX53_PAD_PATA_DA_2__GPIO7_8 0x80000000 + MX53_PAD_GPIO_16__GPIO7_11 0x80000000 + >; + }; + + led_pin_gpio7_7: led_gpio7_7@0 { + fsl,pins = < + MX53_PAD_PATA_DA_1__GPIO7_7 0x80000000 + >; + }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC 0x80000000 + MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD 0x80000000 + MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x80000000 + MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD 0x80000000 + >; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5 + MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5 + MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5 + MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5 + MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5 + MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5 + >; + }; + + pinctrl_esdhc3: esdhc3grp { + fsl,pins = < + MX53_PAD_PATA_DATA8__ESDHC3_DAT0 0x1d5 + MX53_PAD_PATA_DATA9__ESDHC3_DAT1 0x1d5 + MX53_PAD_PATA_DATA10__ESDHC3_DAT2 0x1d5 + MX53_PAD_PATA_DATA11__ESDHC3_DAT3 0x1d5 + MX53_PAD_PATA_DATA0__ESDHC3_DAT4 0x1d5 + MX53_PAD_PATA_DATA1__ESDHC3_DAT5 0x1d5 + MX53_PAD_PATA_DATA2__ESDHC3_DAT6 0x1d5 + MX53_PAD_PATA_DATA3__ESDHC3_DAT7 0x1d5 + MX53_PAD_PATA_RESET_B__ESDHC3_CMD 0x1d5 + MX53_PAD_PATA_IORDY__ESDHC3_CLK 0x1d5 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX53_PAD_FEC_MDC__FEC_MDC 0x80000000 + MX53_PAD_FEC_MDIO__FEC_MDIO 0x80000000 + MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x80000000 + MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x80000000 + MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x80000000 + MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x80000000 + MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x80000000 + MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000 + MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x80000000 + MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x80000000 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX53_PAD_CSI0_DAT8__I2C1_SDA 0xc0000000 + MX53_PAD_CSI0_DAT9__I2C1_SCL 0xc0000000 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX53_PAD_KEY_ROW3__I2C2_SDA 0xc0000000 + MX53_PAD_KEY_COL3__I2C2_SCL 0xc0000000 + >; + }; + + pinctrl_ipu_disp0: ipudisp0grp { + fsl,pins = < + MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK 0x5 + MX53_PAD_DI0_PIN15__IPU_DI0_PIN15 0x5 + MX53_PAD_DI0_PIN2__IPU_DI0_PIN2 0x5 + MX53_PAD_DI0_PIN3__IPU_DI0_PIN3 0x5 + MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0 0x5 + MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1 0x5 + MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2 0x5 + MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3 0x5 + MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4 0x5 + MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5 0x5 + MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6 0x5 + MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7 0x5 + MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8 0x5 + MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9 0x5 + MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10 0x5 + MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11 0x5 + MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12 0x5 + MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13 0x5 + MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14 0x5 + MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15 0x5 + MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16 0x5 + MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17 0x5 + MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18 0x5 + MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19 0x5 + MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20 0x5 + MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21 0x5 + MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22 0x5 + MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23 0x5 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4 + MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4 + >; + }; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + sgtl5000: codec@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + VDDA-supply = <®_3p2v>; + VDDIO-supply = <®_3p2v>; + clocks = <&clks IMX5_CLK_SSI_EXT1_GATE>; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + accelerometer: mma8450@1c { + compatible = "fsl,mma8450"; + reg = <0x1c>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + phy-mode = "rmii"; + phy-reset-gpios = <&gpio7 6 0>; + status = "okay"; +}; + +&sata { + status = "okay"; +}; + +&vpu { + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usb_vbus>; + phy_type = "utmi"; + status = "okay"; +}; + +&usbotg { + dr_mode = "peripheral"; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx53-qsb.dts b/arch/arm/boot/dts/imx53-qsb.dts index 8b254289344f..dec4b073ceb1 100644 --- a/arch/arm/boot/dts/imx53-qsb.dts +++ b/arch/arm/boot/dts/imx53-qsb.dts @@ -11,202 +11,14 @@ */ /dts-v1/; -#include "imx53.dtsi" +#include "imx53-qsb-common.dtsi" / { model = "Freescale i.MX53 Quick Start Board"; compatible = "fsl,imx53-qsb", "fsl,imx53"; - - memory { - reg = <0x70000000 0x40000000>; - }; - - display0: display@di0 { - compatible = "fsl,imx-parallel-display"; - interface-pix-fmt = "rgb565"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ipu_disp0_1>; - status = "disabled"; - display-timings { - claawvga { - native-mode; - clock-frequency = <27000000>; - hactive = <800>; - vactive = <480>; - hback-porch = <40>; - hfront-porch = <60>; - vback-porch = <10>; - vfront-porch = <10>; - hsync-len = <20>; - vsync-len = <10>; - hsync-active = <0>; - vsync-active = <0>; - de-active = <1>; - pixelclk-active = <0>; - }; - }; - - port { - display0_in: endpoint { - remote-endpoint = <&ipu_di0_disp0>; - }; - }; - }; - - gpio-keys { - compatible = "gpio-keys"; - - power { - label = "Power Button"; - gpios = <&gpio1 8 0>; - linux,code = <116>; /* KEY_POWER */ - }; - - volume-up { - label = "Volume Up"; - gpios = <&gpio2 14 0>; - linux,code = <115>; /* KEY_VOLUMEUP */ - gpio-key,wakeup; - }; - - volume-down { - label = "Volume Down"; - gpios = <&gpio2 15 0>; - linux,code = <114>; /* KEY_VOLUMEDOWN */ - gpio-key,wakeup; - }; - }; - - leds { - compatible = "gpio-leds"; - pinctrl-names = "default"; - pinctrl-0 = <&led_pin_gpio7_7>; - - user { - label = "Heartbeat"; - gpios = <&gpio7 7 0>; - linux,default-trigger = "heartbeat"; - }; - }; - - regulators { - compatible = "simple-bus"; - - reg_3p2v: 3p2v { - compatible = "regulator-fixed"; - regulator-name = "3P2V"; - regulator-min-microvolt = <3200000>; - regulator-max-microvolt = <3200000>; - regulator-always-on; - }; - - reg_usb_vbus: usb_vbus { - compatible = "regulator-fixed"; - regulator-name = "usb_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpio7 8 0>; - enable-active-high; - }; - }; - - sound { - compatible = "fsl,imx53-qsb-sgtl5000", - "fsl,imx-audio-sgtl5000"; - model = "imx53-qsb-sgtl5000"; - ssi-controller = <&ssi2>; - audio-codec = <&sgtl5000>; - audio-routing = - "MIC_IN", "Mic Jack", - "Mic Jack", "Mic Bias", - "Headphone Jack", "HP_OUT"; - mux-int-port = <2>; - mux-ext-port = <5>; - }; -}; - -&esdhc1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc1_1>; - status = "okay"; -}; - -&ipu_di0_disp0 { - remote-endpoint = <&display0_in>; -}; - -&ssi2 { - fsl,mode = "i2s-slave"; - status = "okay"; -}; - -&esdhc3 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc3_1>; - cd-gpios = <&gpio3 11 0>; - wp-gpios = <&gpio3 12 0>; - bus-width = <8>; - status = "okay"; -}; - -&iomuxc { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_hog>; - - hog { - pinctrl_hog: hoggrp { - fsl,pins = < - MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000 - MX53_PAD_GPIO_8__GPIO1_8 0x80000000 - MX53_PAD_PATA_DATA14__GPIO2_14 0x80000000 - MX53_PAD_PATA_DATA15__GPIO2_15 0x80000000 - MX53_PAD_EIM_DA11__GPIO3_11 0x80000000 - MX53_PAD_EIM_DA12__GPIO3_12 0x80000000 - MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000 - MX53_PAD_PATA_DA_2__GPIO7_8 0x80000000 - MX53_PAD_GPIO_16__GPIO7_11 0x80000000 - >; - }; - - led_pin_gpio7_7: led_gpio7_7@0 { - fsl,pins = < - MX53_PAD_PATA_DA_1__GPIO7_7 0x80000000 - >; - }; - }; - -}; - -&uart1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_1>; - status = "okay"; -}; - -&i2c2 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2_1>; - status = "okay"; - - sgtl5000: codec@0a { - compatible = "fsl,sgtl5000"; - reg = <0x0a>; - VDDA-supply = <®_3p2v>; - VDDIO-supply = <®_3p2v>; - clocks = <&clks 150>; - }; }; &i2c1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1_1>; - status = "okay"; - - accelerometer: mma8450@1c { - compatible = "fsl,mma8450"; - reg = <0x1c>; - }; - pmic: dialog@48 { compatible = "dlg,da9053-aa", "dlg,da9052"; reg = <0x48>; @@ -301,32 +113,3 @@ }; }; }; - -&audmux { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_audmux_1>; - status = "okay"; -}; - -&fec { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec_1>; - phy-mode = "rmii"; - phy-reset-gpios = <&gpio7 6 0>; - status = "okay"; -}; - -&vpu { - status = "okay"; -}; - -&usbh1 { - vbus-supply = <®_usb_vbus>; - phy_type = "utmi"; - status = "okay"; -}; - -&usbotg { - dr_mode = "peripheral"; - status = "okay"; -}; diff --git a/arch/arm/boot/dts/imx53-qsrb.dts b/arch/arm/boot/dts/imx53-qsrb.dts new file mode 100644 index 000000000000..f1bbf9a32991 --- /dev/null +++ b/arch/arm/boot/dts/imx53-qsrb.dts @@ -0,0 +1,158 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; + +#include "imx53-qsb-common.dtsi" + +/ { + model = "Freescale i.MX53 Quick Start-R Board"; + compatible = "fsl,imx53-qsrb", "fsl,imx53"; +}; + +&iomuxc { + i2c1 { + /* open drain */ + pinctrl_i2c1_qsrb: i2c1grp-1 { + fsl,pins = < + MX53_PAD_CSI0_DAT8__I2C1_SDA 0x400001ec + MX53_PAD_CSI0_DAT9__I2C1_SCL 0x400001ec + >; + }; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1_qsrb>; + status = "okay"; + + pmic: mc34708@8 { + compatible = "fsl,mc34708"; + reg = <0x08>; + interrupt-parent = <&gpio5>; + interrupts = <23 0x8>; + regulators { + sw1_reg: sw1a { + regulator-name = "SW1"; + regulator-min-microvolt = <650000>; + regulator-max-microvolt = <1437500>; + regulator-boot-on; + regulator-always-on; + }; + + sw1b_reg: sw1b { + regulator-name = "SW1B"; + regulator-min-microvolt = <650000>; + regulator-max-microvolt = <1437500>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-name = "SW2"; + regulator-min-microvolt = <650000>; + regulator-max-microvolt = <1437500>; + regulator-boot-on; + regulator-always-on; + }; + + sw3_reg: sw3 { + regulator-name = "SW3"; + regulator-min-microvolt = <650000>; + regulator-max-microvolt = <1425000>; + regulator-boot-on; + }; + + sw4a_reg: sw4a { + regulator-name = "SW4A"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4b_reg: sw4b { + regulator-name = "SW4B"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw5_reg: sw5 { + regulator-name = "SW5"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + swbst_reg: swbst { + regulator-name = "SWBST"; + regulator-boot-on; + regulator-always-on; + }; + + vpll_reg: vpll { + regulator-name = "VPLL"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + }; + + vrefddr_reg: vrefddr { + regulator-name = "VREFDDR"; + regulator-boot-on; + regulator-always-on; + }; + + vusb_reg: vusb { + regulator-name = "VUSB"; + regulator-boot-on; + regulator-always-on; + }; + + vusb2_reg: vusb2 { + regulator-name = "VUSB2"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vdac_reg: vdac { + regulator-name = "VDAC"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2775000>; + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-name = "VGEN1"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1550000>; + regulator-boot-on; + regulator-always-on; + }; + + vgen2_reg: vgen2 { + regulator-name = "VGEN2"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/imx53-smd.dts b/arch/arm/boot/dts/imx53-smd.dts index a9b6e10de0a5..5ec1590ff7bc 100644 --- a/arch/arm/boot/dts/imx53-smd.dts +++ b/arch/arm/boot/dts/imx53-smd.dts @@ -40,7 +40,7 @@ &esdhc1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc1_1>; + pinctrl-0 = <&pinctrl_esdhc1>; cd-gpios = <&gpio3 13 0>; wp-gpios = <&gpio4 11 0>; status = "okay"; @@ -48,21 +48,21 @@ &esdhc2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc2_1>; + pinctrl-0 = <&pinctrl_esdhc2>; non-removable; status = "okay"; }; &uart3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart3_1>; + pinctrl-0 = <&pinctrl_uart3>; fsl,uart-has-rtscts; status = "okay"; }; &ecspi1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi1_1>; + pinctrl-0 = <&pinctrl_ecspi1>; fsl,spi-num-chipselects = <2>; cs-gpios = <&gpio2 30 0>, <&gpio3 19 0>; status = "okay"; @@ -95,7 +95,7 @@ &esdhc3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc3_1>; + pinctrl-0 = <&pinctrl_esdhc3>; non-removable; status = "okay"; }; @@ -104,7 +104,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; - hog { + imx53-smd { pinctrl_hog: hoggrp { fsl,pins = < MX53_PAD_PATA_DATA14__GPIO2_14 0x80000000 @@ -116,24 +116,121 @@ MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000 >; }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX53_PAD_EIM_D16__ECSPI1_SCLK 0x80000000 + MX53_PAD_EIM_D17__ECSPI1_MISO 0x80000000 + MX53_PAD_EIM_D18__ECSPI1_MOSI 0x80000000 + >; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5 + MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5 + MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5 + MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5 + MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5 + MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5 + >; + }; + + pinctrl_esdhc2: esdhc2grp { + fsl,pins = < + MX53_PAD_SD2_CMD__ESDHC2_CMD 0x1d5 + MX53_PAD_SD2_CLK__ESDHC2_CLK 0x1d5 + MX53_PAD_SD2_DATA0__ESDHC2_DAT0 0x1d5 + MX53_PAD_SD2_DATA1__ESDHC2_DAT1 0x1d5 + MX53_PAD_SD2_DATA2__ESDHC2_DAT2 0x1d5 + MX53_PAD_SD2_DATA3__ESDHC2_DAT3 0x1d5 + >; + }; + + pinctrl_esdhc3: esdhc3grp { + fsl,pins = < + MX53_PAD_PATA_DATA8__ESDHC3_DAT0 0x1d5 + MX53_PAD_PATA_DATA9__ESDHC3_DAT1 0x1d5 + MX53_PAD_PATA_DATA10__ESDHC3_DAT2 0x1d5 + MX53_PAD_PATA_DATA11__ESDHC3_DAT3 0x1d5 + MX53_PAD_PATA_DATA0__ESDHC3_DAT4 0x1d5 + MX53_PAD_PATA_DATA1__ESDHC3_DAT5 0x1d5 + MX53_PAD_PATA_DATA2__ESDHC3_DAT6 0x1d5 + MX53_PAD_PATA_DATA3__ESDHC3_DAT7 0x1d5 + MX53_PAD_PATA_RESET_B__ESDHC3_CMD 0x1d5 + MX53_PAD_PATA_IORDY__ESDHC3_CLK 0x1d5 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX53_PAD_FEC_MDC__FEC_MDC 0x80000000 + MX53_PAD_FEC_MDIO__FEC_MDIO 0x80000000 + MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x80000000 + MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x80000000 + MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x80000000 + MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x80000000 + MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x80000000 + MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000 + MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x80000000 + MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x80000000 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX53_PAD_CSI0_DAT8__I2C1_SDA 0xc0000000 + MX53_PAD_CSI0_DAT9__I2C1_SCL 0xc0000000 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX53_PAD_KEY_ROW3__I2C2_SDA 0xc0000000 + MX53_PAD_KEY_COL3__I2C2_SCL 0xc0000000 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4 + MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4 + MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4 + MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4 + MX53_PAD_PATA_DA_1__UART3_CTS 0x1e4 + MX53_PAD_PATA_DA_2__UART3_RTS 0x1e4 + >; + }; }; }; &uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_1>; + pinctrl-0 = <&pinctrl_uart1>; status = "okay"; }; &uart2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2_1>; + pinctrl-0 = <&pinctrl_uart2>; status = "okay"; }; &i2c2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2_1>; + pinctrl-0 = <&pinctrl_i2c2>; status = "okay"; codec: sgtl5000@0a { @@ -154,7 +251,7 @@ &i2c1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1_1>; + pinctrl-0 = <&pinctrl_i2c1>; status = "okay"; accelerometer: mma8450@1c { @@ -175,7 +272,7 @@ &fec { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec_1>; + pinctrl-0 = <&pinctrl_fec>; phy-mode = "rmii"; phy-reset-gpios = <&gpio7 6 0>; status = "okay"; diff --git a/arch/arm/boot/dts/imx53-tqma53.dtsi b/arch/arm/boot/dts/imx53-tqma53.dtsi index abd72af545bf..4f1f0e2868bf 100644 --- a/arch/arm/boot/dts/imx53-tqma53.dtsi +++ b/arch/arm/boot/dts/imx53-tqma53.dtsi @@ -22,9 +22,12 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_3p3v: 3p3v { + reg_3p3v: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "3P3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; @@ -35,8 +38,8 @@ &esdhc2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc2_1>, - <&pinctrl_tqma53_esdhc2_2>; + pinctrl-0 = <&pinctrl_esdhc2>, + <&pinctrl_esdhc2_cdwp>; vmmc-supply = <®_3p3v>; wp-gpios = <&gpio1 2 0>; cd-gpios = <&gpio1 4 0>; @@ -45,13 +48,13 @@ &uart3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart3_2>; + pinctrl-0 = <&pinctrl_uart3>; status = "disabled"; }; &ecspi1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi1_1>; + pinctrl-0 = <&pinctrl_ecspi1>; fsl,spi-num-chipselects = <4>; cs-gpios = <&gpio2 30 0>, <&gpio3 19 0>, <&gpio3 24 0>, <&gpio3 25 0>; @@ -60,7 +63,7 @@ &esdhc3 { /* EMMC */ pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc3_1>; + pinctrl-0 = <&pinctrl_esdhc3>; vmmc-supply = <®_3p3v>; non-removable; bus-width = <8>; @@ -71,27 +74,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; - esdhc2_2 { - pinctrl_tqma53_esdhc2_2: esdhc2-tqma53-grp2 { - fsl,pins = < - MX53_PAD_GPIO_4__GPIO1_4 0x80000000 /* SD2_CD */ - MX53_PAD_GPIO_2__GPIO1_2 0x80000000 /* SD2_WP */ - >; - }; - }; - - i2s { - pinctrl_i2s_1: i2s-grp1 { - fsl,pins = < - MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC 0x80000000 /* I2S_SCLK */ - MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD 0x80000000 /* I2S_DOUT */ - MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x80000000 /* I2S_LRCLK */ - MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD 0x80000000 /* I2S_DIN */ - >; - }; - }; - - hog { + imx53-tqma53 { pinctrl_hog: hoggrp { fsl,pins = < MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000 /* SSI_MCLK */ @@ -107,43 +90,165 @@ MX53_PAD_GPIO_1__PWM2_PWMO 0x80000000 /* LCD_CONTRAST */ >; }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC 0x80000000 + MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD 0x80000000 + MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x80000000 + MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD 0x80000000 + >; + }; + + pinctrl_can1: can1grp { + fsl,pins = < + MX53_PAD_KEY_COL2__CAN1_TXCAN 0x80000000 + MX53_PAD_KEY_ROW2__CAN1_RXCAN 0x80000000 + >; + }; + + pinctrl_can2: can2grp { + fsl,pins = < + MX53_PAD_KEY_COL4__CAN2_TXCAN 0x80000000 + MX53_PAD_KEY_ROW4__CAN2_RXCAN 0x80000000 + >; + }; + + pinctrl_cspi: cspigrp { + fsl,pins = < + MX53_PAD_SD1_DATA0__CSPI_MISO 0x1d5 + MX53_PAD_SD1_CMD__CSPI_MOSI 0x1d5 + MX53_PAD_SD1_CLK__CSPI_SCLK 0x1d5 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX53_PAD_EIM_D16__ECSPI1_SCLK 0x80000000 + MX53_PAD_EIM_D17__ECSPI1_MISO 0x80000000 + MX53_PAD_EIM_D18__ECSPI1_MOSI 0x80000000 + >; + }; + + pinctrl_esdhc2: esdhc2grp { + fsl,pins = < + MX53_PAD_SD2_CMD__ESDHC2_CMD 0x1d5 + MX53_PAD_SD2_CLK__ESDHC2_CLK 0x1d5 + MX53_PAD_SD2_DATA0__ESDHC2_DAT0 0x1d5 + MX53_PAD_SD2_DATA1__ESDHC2_DAT1 0x1d5 + MX53_PAD_SD2_DATA2__ESDHC2_DAT2 0x1d5 + MX53_PAD_SD2_DATA3__ESDHC2_DAT3 0x1d5 + >; + }; + + pinctrl_esdhc2_cdwp: esdhc2cdwp { + fsl,pins = < + MX53_PAD_GPIO_4__GPIO1_4 0x80000000 /* SD2_CD */ + MX53_PAD_GPIO_2__GPIO1_2 0x80000000 /* SD2_WP */ + >; + }; + + pinctrl_esdhc3: esdhc3grp { + fsl,pins = < + MX53_PAD_PATA_DATA8__ESDHC3_DAT0 0x1d5 + MX53_PAD_PATA_DATA9__ESDHC3_DAT1 0x1d5 + MX53_PAD_PATA_DATA10__ESDHC3_DAT2 0x1d5 + MX53_PAD_PATA_DATA11__ESDHC3_DAT3 0x1d5 + MX53_PAD_PATA_DATA0__ESDHC3_DAT4 0x1d5 + MX53_PAD_PATA_DATA1__ESDHC3_DAT5 0x1d5 + MX53_PAD_PATA_DATA2__ESDHC3_DAT6 0x1d5 + MX53_PAD_PATA_DATA3__ESDHC3_DAT7 0x1d5 + MX53_PAD_PATA_RESET_B__ESDHC3_CMD 0x1d5 + MX53_PAD_PATA_IORDY__ESDHC3_CLK 0x1d5 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX53_PAD_FEC_MDC__FEC_MDC 0x80000000 + MX53_PAD_FEC_MDIO__FEC_MDIO 0x80000000 + MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x80000000 + MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x80000000 + MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x80000000 + MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x80000000 + MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x80000000 + MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000 + MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x80000000 + MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x80000000 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX53_PAD_KEY_ROW3__I2C2_SDA 0xc0000000 + MX53_PAD_KEY_COL3__I2C2_SCL 0xc0000000 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX53_PAD_GPIO_6__I2C3_SDA 0xc0000000 + MX53_PAD_GPIO_5__I2C3_SCL 0xc0000000 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4 + MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4 + MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4 + MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4 + >; + }; }; }; &uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_2>; + pinctrl-0 = <&pinctrl_uart1>; fsl,uart-has-rtscts; status = "disabled"; }; &uart2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2_1>; + pinctrl-0 = <&pinctrl_uart2>; status = "disabled"; }; &can1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_can1_2>; + pinctrl-0 = <&pinctrl_can1>; status = "disabled"; }; &can2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_can2_1>; + pinctrl-0 = <&pinctrl_can2>; status = "disabled"; }; &i2c3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c3_1>; + pinctrl-0 = <&pinctrl_i2c3>; status = "disabled"; }; &cspi { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_cspi_1>; + pinctrl-0 = <&pinctrl_cspi>; fsl,spi-num-chipselects = <3>; cs-gpios = <&gpio1 18 0>, <&gpio1 19 0>, <&gpio1 21 0>; @@ -152,7 +257,7 @@ &i2c2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2_1>; + pinctrl-0 = <&pinctrl_i2c2>; status = "okay"; pmic: mc34708@8 { @@ -177,7 +282,7 @@ &fec { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec_1>; + pinctrl-0 = <&pinctrl_fec>; phy-mode = "rmii"; status = "disabled"; }; diff --git a/arch/arm/boot/dts/imx53-tx53-x03x.dts b/arch/arm/boot/dts/imx53-tx53-x03x.dts new file mode 100644 index 000000000000..0217dde3b36b --- /dev/null +++ b/arch/arm/boot/dts/imx53-tx53-x03x.dts @@ -0,0 +1,315 @@ +/* + * Copyright 2013 Lothar Waßmann <LW@KARO-electronics.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx53-tx53.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/pwm/pwm.h> + +/ { + model = "Ka-Ro electronics TX53 module (LCD)"; + compatible = "karo,tx53", "fsl,imx53"; + + aliases { + display = &display; + }; + + soc { + display: display@di0 { + compatible = "fsl,imx-parallel-display"; + crtcs = <&ipu 0>; + interface-pix-fmt = "rgb24"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rgb24_vga1>; + status = "okay"; + + display-timings { + VGA { + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <48>; + hsync-len = <96>; + hfront-porch = <16>; + vback-porch = <31>; + vsync-len = <2>; + vfront-porch = <12>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ETV570 { + clock-frequency = <25200000>; + hactive = <640>; + vactive = <480>; + hback-porch = <114>; + hsync-len = <30>; + hfront-porch = <16>; + vback-porch = <32>; + vsync-len = <3>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ET0350 { + clock-frequency = <6413760>; + hactive = <320>; + vactive = <240>; + hback-porch = <34>; + hsync-len = <34>; + hfront-porch = <20>; + vback-porch = <15>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ET0430 { + clock-frequency = <9009000>; + hactive = <480>; + vactive = <272>; + hback-porch = <2>; + hsync-len = <41>; + hfront-porch = <2>; + vback-porch = <2>; + vsync-len = <10>; + vfront-porch = <2>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <1>; + }; + + ET0500 { + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ET0700 { /* same as ET0500 */ + clock-frequency = <33264000>; + hactive = <800>; + vactive = <480>; + hback-porch = <88>; + hsync-len = <128>; + hfront-porch = <40>; + vback-porch = <33>; + vsync-len = <2>; + vfront-porch = <10>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + + ETQ570 { + clock-frequency = <6596040>; + hactive = <320>; + vactive = <240>; + hback-porch = <38>; + hsync-len = <30>; + hfront-porch = <30>; + vback-porch = <16>; + vsync-len = <3>; + vfront-porch = <4>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + pwms = <&pwm2 0 500000 PWM_POLARITY_INVERTED>; + power-supply = <®_3v3>; + brightness-levels = < + 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100 + >; + default-brightness-level = <50>; + }; + + regulators { + reg_lcd_pwr: regulator@5 { + compatible = "regulator-fixed"; + reg = <5>; + regulator-name = "LCD POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + + reg_lcd_reset: regulator@6 { + compatible = "regulator-fixed"; + reg = <6>; + regulator-name = "LCD RESET"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + }; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + sgtl5000: codec@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + VDDA-supply = <®_2v5>; + VDDIO-supply = <®_3v3>; + clocks = <&mclk>; + }; + + polytouch: edt-ft5x06@38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_edt_ft5x06_1>; + interrupt-parent = <&gpio6>; + interrupts = <15 0>; + reset-gpios = <&gpio2 22 GPIO_ACTIVE_LOW>; + wake-gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; + }; + + touchscreen: tsc2007@48 { + compatible = "ti,tsc2007"; + reg = <0x48>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_tsc2007>; + interrupt-parent = <&gpio3>; + interrupts = <26 0>; + gpios = <&gpio3 26 GPIO_ACTIVE_LOW>; + ti,x-plate-ohms = <660>; + linux,wakeup; + }; +}; + +&iomuxc { + imx53-tx53-x03x { + pinctrl_edt_ft5x06_1: edt-ft5x06grp-1 { + fsl,pins = < + MX53_PAD_NANDF_CS2__GPIO6_15 0x1f0 /* Interrupt */ + MX53_PAD_EIM_A16__GPIO2_22 0x04 /* Reset */ + MX53_PAD_EIM_A17__GPIO2_21 0x04 /* Wake */ + >; + }; + + pinctrl_kpp: kppgrp { + fsl,pins = < + MX53_PAD_GPIO_9__KPP_COL_6 0x1f4 + MX53_PAD_GPIO_4__KPP_COL_7 0x1f4 + MX53_PAD_KEY_COL2__KPP_COL_2 0x1f4 + MX53_PAD_KEY_COL3__KPP_COL_3 0x1f4 + MX53_PAD_GPIO_2__KPP_ROW_6 0x1f4 + MX53_PAD_GPIO_5__KPP_ROW_7 0x1f4 + MX53_PAD_KEY_ROW2__KPP_ROW_2 0x1f4 + MX53_PAD_KEY_ROW3__KPP_ROW_3 0x1f4 + >; + }; + + pinctrl_rgb24_vga1: rgb24-vgagrp1 { + fsl,pins = < + MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK 0x5 + MX53_PAD_DI0_PIN15__IPU_DI0_PIN15 0x5 + MX53_PAD_DI0_PIN2__IPU_DI0_PIN2 0x5 + MX53_PAD_DI0_PIN3__IPU_DI0_PIN3 0x5 + MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0 0x5 + MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1 0x5 + MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2 0x5 + MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3 0x5 + MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4 0x5 + MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5 0x5 + MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6 0x5 + MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7 0x5 + MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8 0x5 + MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9 0x5 + MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10 0x5 + MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11 0x5 + MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12 0x5 + MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13 0x5 + MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14 0x5 + MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15 0x5 + MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16 0x5 + MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17 0x5 + MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18 0x5 + MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19 0x5 + MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20 0x5 + MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21 0x5 + MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22 0x5 + MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23 0x5 + >; + }; + + pinctrl_tsc2007: tsc2007grp { + fsl,pins = < + MX53_PAD_EIM_D26__GPIO3_26 0x1f0 /* Interrupt */ + >; + }; + }; +}; + +&kpp { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp>; + /* sample keymap */ + /* row/col 0,1 are mapped to KPP row/col 6,7 */ + linux,keymap = < + MATRIX_KEY(6, 6, KEY_POWER) + MATRIX_KEY(6, 7, KEY_KP0) + MATRIX_KEY(6, 2, KEY_KP1) + MATRIX_KEY(6, 3, KEY_KP2) + MATRIX_KEY(7, 6, KEY_KP3) + MATRIX_KEY(7, 7, KEY_KP4) + MATRIX_KEY(7, 2, KEY_KP5) + MATRIX_KEY(7, 3, KEY_KP6) + MATRIX_KEY(2, 6, KEY_KP7) + MATRIX_KEY(2, 7, KEY_KP8) + MATRIX_KEY(2, 2, KEY_KP9) + >; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx53-tx53-x13x.dts b/arch/arm/boot/dts/imx53-tx53-x13x.dts new file mode 100644 index 000000000000..64804719f0f4 --- /dev/null +++ b/arch/arm/boot/dts/imx53-tx53-x13x.dts @@ -0,0 +1,243 @@ +/* + * Copyright 2013 Lothar Waßmann <LW@KARO-electronics.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx53-tx53.dtsi" +#include <dt-bindings/input/input.h> + +/ { + model = "Ka-Ro electronics TX53 module (LVDS)"; + compatible = "karo,tx53", "fsl,imx53"; + + aliases { + display = &lvds0; + lvds0 = &lvds0; + lvds1 = &lvds1; + }; + + backlight0: backlight0 { + compatible = "pwm-backlight"; + pwms = <&pwm2 0 500000 0>; + power-supply = <®_3v3>; + brightness-levels = < + 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100 + >; + default-brightness-level = <50>; + }; + + backlight1: backlight1 { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 500000 0>; + power-supply = <®_3v3>; + brightness-levels = < + 0 1 2 3 4 5 6 7 8 9 + 10 11 12 13 14 15 16 17 18 19 + 20 21 22 23 24 25 26 27 28 29 + 30 31 32 33 34 35 36 37 38 39 + 40 41 42 43 44 45 46 47 48 49 + 50 51 52 53 54 55 56 57 58 59 + 60 61 62 63 64 65 66 67 68 69 + 70 71 72 73 74 75 76 77 78 79 + 80 81 82 83 84 85 86 87 88 89 + 90 91 92 93 94 95 96 97 98 99 + 100 + >; + default-brightness-level = <50>; + }; + + regulators { + reg_lcd_pwr0: regulator@5 { + compatible = "regulator-fixed"; + reg = <5>; + regulator-name = "LVDS0 POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 29 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + + reg_lcd_pwr1: regulator@6 { + compatible = "regulator-fixed"; + reg = <6>; + regulator-name = "LVDS1 POWER"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 31 GPIO_ACTIVE_HIGH>; + enable-active-high; + regulator-boot-on; + }; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + touchscreen2: eeti@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eeti2>; + interrupt-parent = <&gpio3>; + interrupts = <23 0>; + wakeup-gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>; + linux,wakeup; + }; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + sgtl5000: codec@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + VDDA-supply = <®_2v5>; + VDDIO-supply = <®_3v3>; + clocks = <&mclk>; + }; + + touchscreen1: eeti@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eeti1>; + interrupt-parent = <&gpio3>; + interrupts = <22 0>; + wakeup-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>; + linux,wakeup; + }; +}; + +&iomuxc { + imx53-tx53-x13x { + pinctrl_i2c2: i2c2-grp1 { + fsl,pins = < + MX53_PAD_KEY_ROW3__I2C2_SDA 0xc0000000 + MX53_PAD_KEY_COL3__I2C2_SCL 0xc0000000 + >; + }; + + pinctrl_lvds0: lvds0grp { + fsl,pins = < + MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3 0x80000000 + MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK 0x80000000 + MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2 0x80000000 + MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1 0x80000000 + MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0 0x80000000 + >; + }; + + pinctrl_lvds1: lvds1grp { + fsl,pins = < + MX53_PAD_LVDS1_TX3_P__LDB_LVDS1_TX3 0x80000000 + MX53_PAD_LVDS1_TX2_P__LDB_LVDS1_TX2 0x80000000 + MX53_PAD_LVDS1_CLK_P__LDB_LVDS1_CLK 0x80000000 + MX53_PAD_LVDS1_TX1_P__LDB_LVDS1_TX1 0x80000000 + MX53_PAD_LVDS1_TX0_P__LDB_LVDS1_TX0 0x80000000 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = <MX53_PAD_GPIO_9__PWM1_PWMO 0x04>; + }; + + pinctrl_eeti1: eeti1grp { + fsl,pins = < + MX53_PAD_EIM_D22__GPIO3_22 0x1f0 /* Interrupt */ + >; + }; + + pinctrl_eeti2: eeti2grp { + fsl,pins = < + MX53_PAD_EIM_D23__GPIO3_23 0x1f0 /* Interrupt */ + >; + }; + }; +}; + +&ldb { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lvds0 &pinctrl_lvds1>; + status = "okay"; + + lvds0: lvds-channel@0 { + fsl,data-mapping = "jeida"; + fsl,data-width = <24>; + status = "okay"; + + display-timings { + native-mode = <&lvds_timing0>; + lvds_timing0: hsd100pxn1 { + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hback-porch = <220>; + hsync-len = <60>; + hfront-porch = <40>; + vback-porch = <21>; + vsync-len = <10>; + vfront-porch = <7>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; + + lvds1: lvds-channel@1 { + fsl,data-mapping = "jeida"; + fsl,data-width = <24>; + status = "okay"; + + display-timings { + native-mode = <&lvds_timing1>; + lvds_timing1: hsd100pxn1 { + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hback-porch = <220>; + hsync-len = <60>; + hfront-porch = <40>; + vback-porch = <21>; + vsync-len = <10>; + vfront-porch = <7>; + hsync-active = <0>; + vsync-active = <0>; + de-active = <1>; + pixelclk-active = <0>; + }; + }; + }; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; +}; + +&sata { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx53-tx53.dtsi b/arch/arm/boot/dts/imx53-tx53.dtsi index f494766700a3..e348796ba689 100644 --- a/arch/arm/boot/dts/imx53-tx53.dtsi +++ b/arch/arm/boot/dts/imx53-tx53.dtsi @@ -1,122 +1,550 @@ /* - * Copyright 2013 Steffen Trumtrar <s.trumtrar@pengutronix.de> + * Copyright 2012 <LW@KARO-electronics.de> + * based on imx53-qsb.dts + * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. * * The code contained herein is licensed under the GNU General Public * License. You may obtain a copy of the GNU General Public License - * Version 2 or later at the following locations: + * Version 2 at the following locations: * * http://www.opensource.org/licenses/gpl-license.html * http://www.gnu.org/copyleft/gpl.html */ -/include/ "imx53.dtsi" +#include "imx53.dtsi" +#include <dt-bindings/gpio/gpio.h> / { - model = "Ka-Ro TX53"; + model = "Ka-Ro electronics TX53 module"; compatible = "karo,tx53", "fsl,imx53"; - memory { - reg = <0x70000000 0x40000000>; /* Up to 1GiB */ + aliases { + can0 = &can2; /* Make the can interface indices consistent with TX28/TX48 modules */ + can1 = &can1; + ipu = &ipu; + reg_can_xcvr = ®_can_xcvr; + usbh1 = &usbh1; + usbotg = &usbotg; + }; + + clocks { + ckih1 { + clock-frequency = <0>; + }; + + mclk: clock@0 { + compatible = "fixed-clock"; + reg = <0>; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_key>; + + power { + label = "Power Button"; + gpios = <&gpio5 2 GPIO_ACTIVE_HIGH>; + linux,code = <116>; /* KEY_POWER */ + gpio-key,wakeup; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_stk5led>; + + user { + label = "Heartbeat"; + gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; }; regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_3p3v: 3p3v { + reg_2v5: regulator@0 { compatible = "regulator-fixed"; - regulator-name = "3P3V"; + reg = <0>; + regulator-name = "2V5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + }; + + reg_3v3: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "3V3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - regulator-always-on; }; + + reg_can_xcvr: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "CAN XCVR"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can_xcvr>; + gpio = <&gpio4 21 GPIO_ACTIVE_HIGH>; + }; + + reg_usbh1_vbus: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "usbh1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1_vbus>; + gpio = <&gpio3 31 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usbotg_vbus: regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "usbotg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg_vbus>; + gpio = <&gpio1 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + }; + + sound { + compatible = "karo,tx53-audio-sgtl5000", "fsl,imx-audio-sgtl5000"; + model = "tx53-audio-sgtl5000"; + ssi-controller = <&ssi1>; + audio-codec = <&sgtl5000>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + /* '1' based port numbers according to datasheet names */ + mux-int-port = <1>; + mux-ext-port = <5>; }; }; +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ssi1>; + status = "okay"; +}; + &can1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_can1_2>; - status = "disabled"; + pinctrl-0 = <&pinctrl_can1>; + xceiver-supply = <®_can_xcvr>; + status = "okay"; }; &can2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_can2_1>; - status = "disabled"; + pinctrl-0 = <&pinctrl_can2>; + xceiver-supply = <®_can_xcvr>; + status = "okay"; }; &ecspi1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi1_2>; - status = "disabled"; + pinctrl-0 = <&pinctrl_ecspi1>; + fsl,spi-num-chipselects = <2>; + status = "okay"; + + cs-gpios = < + &gpio2 30 GPIO_ACTIVE_HIGH + &gpio3 19 GPIO_ACTIVE_HIGH + >; + + spidev0: spi@0 { + compatible = "spidev"; + reg = <0>; + spi-max-frequency = <54000000>; + }; + + spidev1: spi@1 { + compatible = "spidev"; + reg = <1>; + spi-max-frequency = <54000000>; + }; }; &esdhc1 { + cd-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; + fsl,wp-controller; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc1_2>; - status = "disabled"; + pinctrl-0 = <&pinctrl_esdhc1>; + status = "okay"; }; &esdhc2 { + cd-gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; + fsl,wp-controller; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_esdhc2_1>; - status = "disabled"; + pinctrl-0 = <&pinctrl_esdhc2>; + status = "okay"; }; &fec { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec_1>; + pinctrl-0 = <&pinctrl_fec>; phy-mode = "rmii"; - status = "disabled"; + phy-reset-gpios = <&gpio7 6 GPIO_ACTIVE_HIGH>; + phy-handle = <&phy0>; + mac-address = [000000000000]; /* placeholder; will be overwritten by bootloader */ + status = "okay"; + + phy0: ethernet-phy@0 { + interrupt-parent = <&gpio2>; + interrupts = <4>; + device_type = "ethernet-phy"; + }; }; -&i2c3 { +&i2c1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c3_2>; - status = "disabled"; + pinctrl-0 = <&pinctrl_i2c1>; + clock-frequency = <400000>; + status = "okay"; + + rtc1: ds1339@68 { + compatible = "dallas,ds1339"; + reg = <0x68>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ds1339>; + interrupt-parent = <&gpio4>; + interrupts = <20 0>; + }; }; -&owire { +&iomuxc { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_owire_1>; - status = "disabled"; + pinctrl-0 = <&pinctrl_hog>; + + imx53-tx53 { + pinctrl_hog: hoggrp { + /* pins not in use by any device on the Starterkit board series */ + fsl,pins = < + /* CMOS Sensor Interface */ + MX53_PAD_CSI0_DAT12__GPIO5_30 0x1f4 + MX53_PAD_CSI0_DAT13__GPIO5_31 0x1f4 + MX53_PAD_CSI0_DAT14__GPIO6_0 0x1f4 + MX53_PAD_CSI0_DAT15__GPIO6_1 0x1f4 + MX53_PAD_CSI0_DAT16__GPIO6_2 0x1f4 + MX53_PAD_CSI0_DAT17__GPIO6_3 0x1f4 + MX53_PAD_CSI0_DAT18__GPIO6_4 0x1f4 + MX53_PAD_CSI0_DAT19__GPIO6_5 0x1f4 + MX53_PAD_CSI0_MCLK__GPIO5_19 0x1f4 + MX53_PAD_CSI0_VSYNC__GPIO5_21 0x1f4 + MX53_PAD_CSI0_PIXCLK__GPIO5_18 0x1f4 + MX53_PAD_GPIO_0__GPIO1_0 0x1f4 + /* Module Specific Signal */ + /* MX53_PAD_NANDF_CS2__GPIO6_15 0x1f4 maybe used by EDT-FT5x06 */ + /* MX53_PAD_EIM_A16__GPIO2_22 0x1f4 maybe used by EDT-FT5x06 */ + MX53_PAD_EIM_D29__GPIO3_29 0x1f4 + MX53_PAD_EIM_EB3__GPIO2_31 0x1f4 + /* MX53_PAD_EIM_A17__GPIO2_21 0x1f4 maybe used by EDT-FT5x06 */ + /* MX53_PAD_EIM_A18__GPIO2_20 0x1f4 used by LED */ + MX53_PAD_EIM_A19__GPIO2_19 0x1f4 + MX53_PAD_EIM_A20__GPIO2_18 0x1f4 + MX53_PAD_EIM_A21__GPIO2_17 0x1f4 + MX53_PAD_EIM_A22__GPIO2_16 0x1f4 + MX53_PAD_EIM_A23__GPIO6_6 0x1f4 + MX53_PAD_EIM_A24__GPIO5_4 0x1f4 + MX53_PAD_CSI0_DAT8__GPIO5_26 0x1f4 + MX53_PAD_CSI0_DAT9__GPIO5_27 0x1f4 + MX53_PAD_CSI0_DAT10__GPIO5_28 0x1f4 + MX53_PAD_CSI0_DAT11__GPIO5_29 0x1f4 + /* MX53_PAD_EIM_D22__GPIO3_22 0x1f4 maybe used by EETI touchpanel driver */ + /* MX53_PAD_EIM_D23__GPIO3_23 0x1f4 maybe used by EETI touchpanel driver */ + MX53_PAD_GPIO_13__GPIO4_3 0x1f4 + MX53_PAD_EIM_CS0__GPIO2_23 0x1f4 + MX53_PAD_EIM_CS1__GPIO2_24 0x1f4 + MX53_PAD_CSI0_DATA_EN__GPIO5_20 0x1f4 + MX53_PAD_EIM_WAIT__GPIO5_0 0x1f4 + MX53_PAD_EIM_EB0__GPIO2_28 0x1f4 + MX53_PAD_EIM_EB1__GPIO2_29 0x1f4 + MX53_PAD_EIM_OE__GPIO2_25 0x1f4 + MX53_PAD_EIM_LBA__GPIO2_27 0x1f4 + MX53_PAD_EIM_RW__GPIO2_26 0x1f4 + MX53_PAD_EIM_DA8__GPIO3_8 0x1f4 + MX53_PAD_EIM_DA9__GPIO3_9 0x1f4 + MX53_PAD_EIM_DA10__GPIO3_10 0x1f4 + MX53_PAD_EIM_DA11__GPIO3_11 0x1f4 + MX53_PAD_EIM_DA12__GPIO3_12 0x1f4 + MX53_PAD_EIM_DA13__GPIO3_13 0x1f4 + MX53_PAD_EIM_DA14__GPIO3_14 0x1f4 + MX53_PAD_EIM_DA15__GPIO3_15 0x1f4 + >; + }; + + pinctrl_can1: can1grp { + fsl,pins = < + MX53_PAD_GPIO_7__CAN1_TXCAN 0x80000000 + MX53_PAD_GPIO_8__CAN1_RXCAN 0x80000000 + >; + }; + + pinctrl_can2: can2grp { + fsl,pins = < + MX53_PAD_KEY_COL4__CAN2_TXCAN 0x80000000 + MX53_PAD_KEY_ROW4__CAN2_RXCAN 0x80000000 + >; + }; + + pinctrl_can_xcvr: can-xcvrgrp { + fsl,pins = <MX53_PAD_DISP0_DAT0__GPIO4_21 0xe0>; /* Flexcan XCVR enable */ + }; + + pinctrl_ds1339: ds1339grp { + fsl,pins = <MX53_PAD_DI0_PIN4__GPIO4_20 0xe0>; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX53_PAD_GPIO_19__ECSPI1_RDY 0x80000000 + MX53_PAD_EIM_EB2__ECSPI1_SS0 0x80000000 + MX53_PAD_EIM_D16__ECSPI1_SCLK 0x80000000 + MX53_PAD_EIM_D17__ECSPI1_MISO 0x80000000 + MX53_PAD_EIM_D18__ECSPI1_MOSI 0x80000000 + MX53_PAD_EIM_D19__ECSPI1_SS1 0x80000000 + >; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5 + MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5 + MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5 + MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5 + MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5 + MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5 + MX53_PAD_EIM_D24__GPIO3_24 0x1f0 + >; + }; + + pinctrl_esdhc2: esdhc2grp { + fsl,pins = < + MX53_PAD_SD2_CMD__ESDHC2_CMD 0x1d5 + MX53_PAD_SD2_CLK__ESDHC2_CLK 0x1d5 + MX53_PAD_SD2_DATA0__ESDHC2_DAT0 0x1d5 + MX53_PAD_SD2_DATA1__ESDHC2_DAT1 0x1d5 + MX53_PAD_SD2_DATA2__ESDHC2_DAT2 0x1d5 + MX53_PAD_SD2_DATA3__ESDHC2_DAT3 0x1d5 + MX53_PAD_EIM_D25__GPIO3_25 0x1f0 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX53_PAD_FEC_MDC__FEC_MDC 0x80000000 + MX53_PAD_FEC_MDIO__FEC_MDIO 0x80000000 + MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x80000000 + MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x80000000 + MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x80000000 + MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x80000000 + MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x80000000 + MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000 + MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x80000000 + MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x80000000 + >; + }; + + pinctrl_gpio_key: gpio-keygrp { + fsl,pins = <MX53_PAD_EIM_A25__GPIO5_2 0x1f4>; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX53_PAD_EIM_D21__I2C1_SCL 0xc0000000 + MX53_PAD_EIM_D28__I2C1_SDA 0xc0000000 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX53_PAD_GPIO_3__I2C3_SCL 0xc0000000 + MX53_PAD_GPIO_6__I2C3_SDA 0xc0000000 + >; + }; + + pinctrl_nand: nandgrp { + fsl,pins = < + MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B 0x4 + MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B 0x4 + MX53_PAD_NANDF_CLE__EMI_NANDF_CLE 0x4 + MX53_PAD_NANDF_ALE__EMI_NANDF_ALE 0x4 + MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B 0xe0 + MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0 0xe0 + MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0 0x4 + MX53_PAD_EIM_DA0__EMI_NAND_WEIM_DA_0 0xa4 + MX53_PAD_EIM_DA1__EMI_NAND_WEIM_DA_1 0xa4 + MX53_PAD_EIM_DA2__EMI_NAND_WEIM_DA_2 0xa4 + MX53_PAD_EIM_DA3__EMI_NAND_WEIM_DA_3 0xa4 + MX53_PAD_EIM_DA4__EMI_NAND_WEIM_DA_4 0xa4 + MX53_PAD_EIM_DA5__EMI_NAND_WEIM_DA_5 0xa4 + MX53_PAD_EIM_DA6__EMI_NAND_WEIM_DA_6 0xa4 + MX53_PAD_EIM_DA7__EMI_NAND_WEIM_DA_7 0xa4 + >; + }; + + pinctrl_pwm2: pwm2grp { + fsl,pins = < + MX53_PAD_GPIO_1__PWM2_PWMO 0x80000000 + >; + }; + + pinctrl_ssi1: ssi1grp { + fsl,pins = < + MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC 0x80000000 + MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD 0x80000000 + MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x80000000 + MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD 0x80000000 + >; + }; + + pinctrl_ssi2: ssi2grp { + fsl,pins = < + MX53_PAD_CSI0_DAT4__AUDMUX_AUD3_TXC 0x80000000 + MX53_PAD_CSI0_DAT5__AUDMUX_AUD3_TXD 0x80000000 + MX53_PAD_CSI0_DAT6__AUDMUX_AUD3_TXFS 0x80000000 + MX53_PAD_CSI0_DAT7__AUDMUX_AUD3_RXD 0x80000000 + MX53_PAD_EIM_D27__GPIO3_27 0x1f0 + >; + }; + + pinctrl_stk5led: stk5ledgrp { + fsl,pins = <MX53_PAD_EIM_A18__GPIO2_20 0xc0>; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4 + MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4 + MX53_PAD_PATA_RESET_B__UART1_CTS 0x1c5 + MX53_PAD_PATA_IORDY__UART1_RTS 0x1c5 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1c5 + MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1c5 + MX53_PAD_PATA_DIOR__UART2_RTS 0x1c5 + MX53_PAD_PATA_INTRQ__UART2_CTS 0x1c5 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4 + MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4 + MX53_PAD_PATA_DA_1__UART3_CTS 0x1e4 + MX53_PAD_PATA_DA_2__UART3_RTS 0x1e4 + >; + }; + + pinctrl_usbh1: usbh1grp { + fsl,pins = < + MX53_PAD_EIM_D30__GPIO3_30 0x100 /* OC */ + >; + }; + + pinctrl_usbh1_vbus: usbh1-vbusgrp { + fsl,pins = < + MX53_PAD_EIM_D31__GPIO3_31 0xe0 /* VBUS ENABLE */ + >; + }; + + pinctrl_usbotg_vbus: usbotg-vbusgrp { + fsl,pins = < + MX53_PAD_GPIO_7__GPIO1_7 0xe0 /* VBUS ENABLE */ + MX53_PAD_GPIO_8__GPIO1_8 0x100 /* OC */ + >; + }; + }; +}; + +&ipu { + status = "okay"; +}; + +&nfc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nand>; + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + nand-on-flash-bbt; + status = "okay"; }; &pwm2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_pwm2_1>; - status = "disabled"; + pinctrl-0 = <&pinctrl_pwm2>; + #pwm-cells = <3>; +}; + +&sdma { + fsl,sdma-ram-script-name = "sdma-imx53.bin"; }; &ssi1 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_audmux_1>; - status = "disabled"; + fsl,mode = "i2s-slave"; + codec-handle = <&sgtl5000>; + status = "okay"; }; &ssi2 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_audmux_2>; status = "disabled"; }; &uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_2>, - <&pinctrl_uart1_3>; + pinctrl-0 = <&pinctrl_uart1>; fsl,uart-has-rtscts; - status = "disabled"; + status = "okay"; }; &uart2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2_2>; + pinctrl-0 = <&pinctrl_uart2>; fsl,uart-has-rtscts; - status = "disabled"; + status = "okay"; }; &uart3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart3_1>; + pinctrl-0 = <&pinctrl_uart3>; fsl,uart-has-rtscts; - status = "disabled"; + status = "okay"; +}; + +&usbh1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1>; + phy_type = "utmi"; + disable-over-current; + vbus-supply = <®_usbh1_vbus>; + status = "okay"; +}; + +&usbotg { + phy_type = "utmi"; + dr_mode = "peripheral"; + disable-over-current; + vbus-supply = <®_usbotg_vbus>; + status = "okay"; }; diff --git a/arch/arm/boot/dts/imx53-voipac-bsb.dts b/arch/arm/boot/dts/imx53-voipac-bsb.dts new file mode 100644 index 000000000000..7f6711a48615 --- /dev/null +++ b/arch/arm/boot/dts/imx53-voipac-bsb.dts @@ -0,0 +1,159 @@ +/* + * Copyright 2013 Rostislav Lisovy <lisovy@gmail.com>, PiKRON s.r.o. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx53-voipac-dmm-668.dtsi" + +/ { + sound { + compatible = "fsl,imx53-voipac-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "imx53-voipac-sgtl5000"; + ssi-controller = <&ssi2>; + audio-codec = <&sgtl5000>; + audio-routing = + "Headphone Jack", "HP_OUT"; + mux-int-port = <2>; + mux-ext-port = <5>; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pin_gpio>; + + led1 { + label = "led-red"; + gpios = <&gpio3 29 0>; + default-state = "off"; + }; + + led2 { + label = "led-orange"; + gpios = <&gpio2 31 0>; + default-state = "off"; + }; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx53-voipac { + pinctrl_hog: hoggrp { + fsl,pins = < + /* SD2_CD */ + MX53_PAD_EIM_D25__GPIO3_25 0x80000000 + /* SD2_WP */ + MX53_PAD_EIM_A19__GPIO2_19 0x80000000 + >; + }; + + led_pin_gpio: led_gpio { + fsl,pins = < + MX53_PAD_EIM_D29__GPIO3_29 0x80000000 + MX53_PAD_EIM_EB3__GPIO2_31 0x80000000 + >; + }; + + /* Keyboard controller */ + pinctrl_kpp_1: kppgrp-1 { + fsl,pins = < + MX53_PAD_GPIO_9__KPP_COL_6 0xe8 + MX53_PAD_GPIO_4__KPP_COL_7 0xe8 + MX53_PAD_KEY_COL2__KPP_COL_2 0xe8 + MX53_PAD_KEY_COL3__KPP_COL_3 0xe8 + MX53_PAD_KEY_COL4__KPP_COL_4 0xe8 + MX53_PAD_GPIO_2__KPP_ROW_6 0xe0 + MX53_PAD_GPIO_5__KPP_ROW_7 0xe0 + MX53_PAD_KEY_ROW2__KPP_ROW_2 0xe0 + MX53_PAD_KEY_ROW3__KPP_ROW_3 0xe0 + MX53_PAD_KEY_ROW4__KPP_ROW_4 0xe0 + >; + }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC 0x80000000 + MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD 0x80000000 + MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x80000000 + MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD 0x80000000 + >; + }; + + pinctrl_esdhc2: esdhc2grp { + fsl,pins = < + MX53_PAD_SD2_CMD__ESDHC2_CMD 0x1d5 + MX53_PAD_SD2_CLK__ESDHC2_CLK 0x1d5 + MX53_PAD_SD2_DATA0__ESDHC2_DAT0 0x1d5 + MX53_PAD_SD2_DATA1__ESDHC2_DAT1 0x1d5 + MX53_PAD_SD2_DATA2__ESDHC2_DAT2 0x1d5 + MX53_PAD_SD2_DATA3__ESDHC2_DAT3 0x1d5 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX53_PAD_GPIO_3__I2C3_SCL 0xc0000000 + MX53_PAD_GPIO_6__I2C3_SDA 0xc0000000 + >; + }; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; /* SSI1 */ + status = "okay"; +}; + +&esdhc2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc2>; + cd-gpios = <&gpio3 25 0>; + wp-gpios = <&gpio2 19 0>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + sgtl5000: codec@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + VDDA-supply = <®_3p3v>; + VDDIO-supply = <®_3p3v>; + clocks = <&clks 150>; + }; +}; + +&kpp { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp_1>; + linux,keymap = < + 0x0203003b /* KEY_F1 */ + 0x0603003c /* KEY_F2 */ + 0x0207003d /* KEY_F3 */ + 0x0607003e /* KEY_F4 */ + >; + keypad,num-rows = <8>; + keypad,num-columns = <1>; + status = "okay"; +}; + +&ssi2 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi b/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi new file mode 100644 index 000000000000..ba689fbd0e41 --- /dev/null +++ b/arch/arm/boot/dts/imx53-voipac-dmm-668.dtsi @@ -0,0 +1,277 @@ +/* + * Copyright 2013 Rostislav Lisovy <lisovy@gmail.com>, PiKRON s.r.o. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#include "imx53.dtsi" + +/ { + model = "Voipac i.MX53 X53-DMM-668"; + compatible = "voipac,imx53-dmm-668", "fsl,imx53"; + + memory@70000000 { + device_type = "memory"; + reg = <0x70000000 0x20000000>; + }; + + memory@b0000000 { + device_type = "memory"; + reg = <0xb0000000 0x20000000>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_3p3v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_vbus: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "usb_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 31 0>; /* PEN */ + enable-active-high; + }; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx53-voipac { + pinctrl_hog: hoggrp { + fsl,pins = < + /* Make DA9053 regulator functional */ + MX53_PAD_GPIO_16__GPIO7_11 0x80000000 + /* FEC Power enable */ + MX53_PAD_GPIO_11__GPIO4_1 0x80000000 + /* FEC RST */ + MX53_PAD_GPIO_12__GPIO4_2 0x80000000 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX53_PAD_EIM_D16__ECSPI1_SCLK 0x80000000 + MX53_PAD_EIM_D17__ECSPI1_MISO 0x80000000 + MX53_PAD_EIM_D18__ECSPI1_MOSI 0x80000000 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX53_PAD_FEC_MDC__FEC_MDC 0x80000000 + MX53_PAD_FEC_MDIO__FEC_MDIO 0x80000000 + MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x80000000 + MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x80000000 + MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x80000000 + MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x80000000 + MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x80000000 + MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000 + MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x80000000 + MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x80000000 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX53_PAD_EIM_D21__I2C1_SCL 0xc0000000 + MX53_PAD_EIM_D28__I2C1_SDA 0xc0000000 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4 + MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4 + >; + }; + + pinctrl_nand: nandgrp { + fsl,pins = < + MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B 0x4 + MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B 0x4 + MX53_PAD_NANDF_CLE__EMI_NANDF_CLE 0x4 + MX53_PAD_NANDF_ALE__EMI_NANDF_ALE 0x4 + MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B 0xe0 + MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0 0xe0 + MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0 0x4 + MX53_PAD_PATA_DATA0__EMI_NANDF_D_0 0xa4 + MX53_PAD_PATA_DATA1__EMI_NANDF_D_1 0xa4 + MX53_PAD_PATA_DATA2__EMI_NANDF_D_2 0xa4 + MX53_PAD_PATA_DATA3__EMI_NANDF_D_3 0xa4 + MX53_PAD_PATA_DATA4__EMI_NANDF_D_4 0xa4 + MX53_PAD_PATA_DATA5__EMI_NANDF_D_5 0xa4 + MX53_PAD_PATA_DATA6__EMI_NANDF_D_6 0xa4 + MX53_PAD_PATA_DATA7__EMI_NANDF_D_7 0xa4 + >; + }; + }; +}; + +&ecspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + fsl,spi-num-chipselects = <4>; + cs-gpios = <&gpio2 30 0>, <&gpio3 19 0>, <&gpio2 16 0>, <&gpio2 17 0>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + phy-mode = "rmii"; + phy-reset-gpios = <&gpio4 2 0>; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic: dialog@48 { + compatible = "dlg,da9053-aa", "dlg,da9052"; + reg = <0x48>; + interrupt-parent = <&gpio7>; + interrupts = <11 0x8>; /* low-level active IRQ at GPIO7_11 */ + + regulators { + buck1_reg: buck1 { + regulator-name = "BUCKCORE"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1400000>; + regulator-always-on; + }; + + buck2_reg: buck2 { + regulator-name = "BUCKPRO"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + buck3_reg: buck3 { + regulator-name = "BUCKMEM"; + regulator-min-microvolt = <1420000>; + regulator-max-microvolt = <1580000>; + regulator-always-on; + }; + + buck4_reg: buck4 { + regulator-name = "BUCKPERI"; + regulator-min-microvolt = <2370000>; + regulator-max-microvolt = <2630000>; + regulator-always-on; + }; + + ldo1_reg: ldo1 { + regulator-name = "ldo1_1v3"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1350000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ldo2 { + regulator-name = "ldo2_1v3"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + ldo3_reg: ldo3 { + regulator-name = "ldo3_3v3"; + regulator-min-microvolt = <3250000>; + regulator-max-microvolt = <3350000>; + regulator-always-on; + }; + + ldo4_reg: ldo4 { + regulator-name = "ldo4_2v775"; + regulator-min-microvolt = <2770000>; + regulator-max-microvolt = <2780000>; + regulator-always-on; + }; + + ldo5_reg: ldo5 { + regulator-name = "ldo5_3v3"; + regulator-min-microvolt = <3250000>; + regulator-max-microvolt = <3350000>; + regulator-always-on; + }; + + ldo6_reg: ldo6 { + regulator-name = "ldo6_1v3"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + + ldo7_reg: ldo7 { + regulator-name = "ldo7_2v75"; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; + + ldo8_reg: ldo8 { + regulator-name = "ldo8_1v8"; + regulator-min-microvolt = <1750000>; + regulator-max-microvolt = <1850000>; + regulator-always-on; + }; + + ldo9_reg: ldo9 { + regulator-name = "ldo9_1v5"; + regulator-min-microvolt = <1450000>; + regulator-max-microvolt = <1550000>; + regulator-always-on; + }; + + ldo10_reg: ldo10 { + regulator-name = "ldo10_1v3"; + regulator-min-microvolt = <1250000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + }; + }; + }; +}; + +&nfc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_nand>; + nand-bus-width = <8>; + nand-ecc-mode = "hw"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usb_vbus>; + phy_type = "utmi"; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx53.dtsi b/arch/arm/boot/dts/imx53.dtsi index 04d3127edfe1..b57ab57740f6 100644 --- a/arch/arm/boot/dts/imx53.dtsi +++ b/arch/arm/boot/dts/imx53.dtsi @@ -12,6 +12,9 @@ #include "skeleton.dtsi" #include "imx53-pinfunc.h" +#include <dt-bindings/clock/imx5-clock.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> / { aliases { @@ -25,6 +28,10 @@ i2c0 = &i2c1; i2c1 = &i2c2; i2c2 = &i2c3; + mmc0 = &esdhc1; + mmc1 = &esdhc2; + mmc2 = &esdhc3; + mmc3 = &esdhc4; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; @@ -89,13 +96,26 @@ interrupt-parent = <&tzic>; ranges; + sata: sata@10000000 { + compatible = "fsl,imx53-ahci"; + reg = <0x10000000 0x1000>; + interrupts = <28>; + clocks = <&clks IMX5_CLK_SATA_GATE>, + <&clks IMX5_CLK_SATA_REF>, + <&clks IMX5_CLK_AHB>; + clock-names = "sata_gate", "sata_ref", "ahb"; + status = "disabled"; + }; + ipu: ipu@18000000 { #address-cells = <1>; #size-cells = <0>; compatible = "fsl,imx53-ipu"; reg = <0x18000000 0x080000000>; interrupts = <11 10>; - clocks = <&clks 59>, <&clks 110>, <&clks 61>; + clocks = <&clks IMX5_CLK_IPU_GATE>, + <&clks IMX5_CLK_IPU_DI0_GATE>, + <&clks IMX5_CLK_IPU_DI1_GATE>; clock-names = "bus", "di0", "di1"; resets = <&src 2>; @@ -153,7 +173,9 @@ compatible = "fsl,imx53-esdhc"; reg = <0x50004000 0x4000>; interrupts = <1>; - clocks = <&clks 44>, <&clks 0>, <&clks 71>; + clocks = <&clks IMX5_CLK_ESDHC1_IPG_GATE>, + <&clks IMX5_CLK_DUMMY>, + <&clks IMX5_CLK_ESDHC1_PER_GATE>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; status = "disabled"; @@ -163,7 +185,9 @@ compatible = "fsl,imx53-esdhc"; reg = <0x50008000 0x4000>; interrupts = <2>; - clocks = <&clks 45>, <&clks 0>, <&clks 72>; + clocks = <&clks IMX5_CLK_ESDHC2_IPG_GATE>, + <&clks IMX5_CLK_DUMMY>, + <&clks IMX5_CLK_ESDHC2_PER_GATE>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; status = "disabled"; @@ -173,7 +197,8 @@ compatible = "fsl,imx53-uart", "fsl,imx21-uart"; reg = <0x5000c000 0x4000>; interrupts = <33>; - clocks = <&clks 32>, <&clks 33>; + clocks = <&clks IMX5_CLK_UART3_IPG_GATE>, + <&clks IMX5_CLK_UART3_PER_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -184,16 +209,19 @@ compatible = "fsl,imx53-ecspi", "fsl,imx51-ecspi"; reg = <0x50010000 0x4000>; interrupts = <36>; - clocks = <&clks 51>, <&clks 52>; + clocks = <&clks IMX5_CLK_ECSPI1_IPG_GATE>, + <&clks IMX5_CLK_ECSPI1_PER_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; ssi2: ssi@50014000 { - compatible = "fsl,imx53-ssi", "fsl,imx21-ssi"; + compatible = "fsl,imx53-ssi", + "fsl,imx51-ssi", + "fsl,imx21-ssi"; reg = <0x50014000 0x4000>; interrupts = <30>; - clocks = <&clks 49>; + clocks = <&clks IMX5_CLK_SSI2_IPG_GATE>; dmas = <&sdma 24 1 0>, <&sdma 25 1 0>; dma-names = "rx", "tx"; @@ -206,7 +234,9 @@ compatible = "fsl,imx53-esdhc"; reg = <0x50020000 0x4000>; interrupts = <3>; - clocks = <&clks 46>, <&clks 0>, <&clks 73>; + clocks = <&clks IMX5_CLK_ESDHC3_IPG_GATE>, + <&clks IMX5_CLK_DUMMY>, + <&clks IMX5_CLK_ESDHC3_PER_GATE>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; status = "disabled"; @@ -216,7 +246,9 @@ compatible = "fsl,imx53-esdhc"; reg = <0x50024000 0x4000>; interrupts = <4>; - clocks = <&clks 47>, <&clks 0>, <&clks 74>; + clocks = <&clks IMX5_CLK_ESDHC4_IPG_GATE>, + <&clks IMX5_CLK_DUMMY>, + <&clks IMX5_CLK_ESDHC4_PER_GATE>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; status = "disabled"; @@ -225,14 +257,14 @@ usbphy0: usbphy@0 { compatible = "usb-nop-xceiv"; - clocks = <&clks 124>; + clocks = <&clks IMX5_CLK_USB_PHY1_GATE>; clock-names = "main_clk"; status = "okay"; }; usbphy1: usbphy@1 { compatible = "usb-nop-xceiv"; - clocks = <&clks 125>; + clocks = <&clks IMX5_CLK_USB_PHY2_GATE>; clock-names = "main_clk"; status = "okay"; }; @@ -241,7 +273,7 @@ compatible = "fsl,imx53-usb", "fsl,imx27-usb"; reg = <0x53f80000 0x0200>; interrupts = <18>; - clocks = <&clks 108>; + clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 0>; fsl,usbphy = <&usbphy0>; status = "disabled"; @@ -251,7 +283,7 @@ compatible = "fsl,imx53-usb", "fsl,imx27-usb"; reg = <0x53f80200 0x0200>; interrupts = <14>; - clocks = <&clks 108>; + clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 1>; fsl,usbphy = <&usbphy1>; status = "disabled"; @@ -261,7 +293,7 @@ compatible = "fsl,imx53-usb", "fsl,imx27-usb"; reg = <0x53f80400 0x0200>; interrupts = <16>; - clocks = <&clks 108>; + clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 2>; status = "disabled"; }; @@ -270,7 +302,7 @@ compatible = "fsl,imx53-usb", "fsl,imx27-usb"; reg = <0x53f80600 0x0200>; interrupts = <17>; - clocks = <&clks 108>; + clocks = <&clks IMX5_CLK_USBOH3_GATE>; fsl,usbmisc = <&usbmisc 3>; status = "disabled"; }; @@ -279,7 +311,7 @@ #index-cells = <1>; compatible = "fsl,imx53-usbmisc"; reg = <0x53f80800 0x200>; - clocks = <&clks 108>; + clocks = <&clks IMX5_CLK_USBOH3_GATE>; }; gpio1: gpio@53f84000 { @@ -322,18 +354,26 @@ #interrupt-cells = <2>; }; + kpp: kpp@53f94000 { + compatible = "fsl,imx53-kpp", "fsl,imx21-kpp"; + reg = <0x53f94000 0x4000>; + interrupts = <60>; + clocks = <&clks IMX5_CLK_DUMMY>; + status = "disabled"; + }; + wdog1: wdog@53f98000 { compatible = "fsl,imx53-wdt", "fsl,imx21-wdt"; reg = <0x53f98000 0x4000>; interrupts = <58>; - clocks = <&clks 0>; + clocks = <&clks IMX5_CLK_DUMMY>; }; wdog2: wdog@53f9c000 { compatible = "fsl,imx53-wdt", "fsl,imx21-wdt"; reg = <0x53f9c000 0x4000>; interrupts = <59>; - clocks = <&clks 0>; + clocks = <&clks IMX5_CLK_DUMMY>; status = "disabled"; }; @@ -341,521 +381,14 @@ compatible = "fsl,imx53-gpt", "fsl,imx31-gpt"; reg = <0x53fa0000 0x4000>; interrupts = <39>; - clocks = <&clks 36>, <&clks 41>; + clocks = <&clks IMX5_CLK_GPT_IPG_GATE>, + <&clks IMX5_CLK_GPT_HF_GATE>; clock-names = "ipg", "per"; }; iomuxc: iomuxc@53fa8000 { compatible = "fsl,imx53-iomuxc"; reg = <0x53fa8000 0x4000>; - - audmux { - pinctrl_audmux_1: audmuxgrp-1 { - fsl,pins = < - MX53_PAD_KEY_COL0__AUDMUX_AUD5_TXC 0x80000000 - MX53_PAD_KEY_ROW0__AUDMUX_AUD5_TXD 0x80000000 - MX53_PAD_KEY_COL1__AUDMUX_AUD5_TXFS 0x80000000 - MX53_PAD_KEY_ROW1__AUDMUX_AUD5_RXD 0x80000000 - >; - }; - - pinctrl_audmux_2: audmuxgrp-2 { - fsl,pins = < - MX53_PAD_SD2_DATA3__AUDMUX_AUD4_TXC 0x80000000 - MX53_PAD_SD2_DATA2__AUDMUX_AUD4_TXD 0x80000000 - MX53_PAD_SD2_DATA1__AUDMUX_AUD4_TXFS 0x80000000 - MX53_PAD_SD2_DATA0__AUDMUX_AUD4_RXD 0x80000000 - >; - }; - - pinctrl_audmux_3: audmuxgrp-3 { - fsl,pins = < - MX53_PAD_CSI0_DAT4__AUDMUX_AUD3_TXC 0x80000000 - MX53_PAD_CSI0_DAT5__AUDMUX_AUD3_TXD 0x80000000 - MX53_PAD_CSI0_DAT6__AUDMUX_AUD3_TXFS 0x80000000 - MX53_PAD_CSI0_DAT7__AUDMUX_AUD3_RXD 0x80000000 - >; - }; - }; - - fec { - pinctrl_fec_1: fecgrp-1 { - fsl,pins = < - MX53_PAD_FEC_MDC__FEC_MDC 0x80000000 - MX53_PAD_FEC_MDIO__FEC_MDIO 0x80000000 - MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x80000000 - MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x80000000 - MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x80000000 - MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x80000000 - MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x80000000 - MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000 - MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x80000000 - MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x80000000 - >; - }; - - pinctrl_fec_2: fecgrp-2 { - fsl,pins = < - MX53_PAD_FEC_MDC__FEC_MDC 0x80000000 - MX53_PAD_FEC_MDIO__FEC_MDIO 0x80000000 - MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x80000000 - MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x80000000 - MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x80000000 - MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x80000000 - MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x80000000 - MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000 - MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x80000000 - MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x80000000 - MX53_PAD_KEY_ROW1__FEC_COL 0x80000000 - MX53_PAD_KEY_COL3__FEC_CRS 0x80000000 - MX53_PAD_KEY_COL2__FEC_RDATA_2 0x80000000 - MX53_PAD_KEY_COL0__FEC_RDATA_3 0x80000000 - MX53_PAD_KEY_COL1__FEC_RX_CLK 0x80000000 - MX53_PAD_KEY_ROW2__FEC_TDATA_2 0x80000000 - MX53_PAD_GPIO_19__FEC_TDATA_3 0x80000000 - MX53_PAD_KEY_ROW0__FEC_TX_ER 0x80000000 - >; - }; - }; - - csi { - pinctrl_csi_1: csigrp-1 { - fsl,pins = < - MX53_PAD_CSI0_DATA_EN__IPU_CSI0_DATA_EN 0x1d5 - MX53_PAD_CSI0_VSYNC__IPU_CSI0_VSYNC 0x1d5 - MX53_PAD_CSI0_MCLK__IPU_CSI0_HSYNC 0x1d5 - MX53_PAD_CSI0_PIXCLK__IPU_CSI0_PIXCLK 0x1d5 - MX53_PAD_CSI0_DAT19__IPU_CSI0_D_19 0x1d5 - MX53_PAD_CSI0_DAT18__IPU_CSI0_D_18 0x1d5 - MX53_PAD_CSI0_DAT17__IPU_CSI0_D_17 0x1d5 - MX53_PAD_CSI0_DAT16__IPU_CSI0_D_16 0x1d5 - MX53_PAD_CSI0_DAT15__IPU_CSI0_D_15 0x1d5 - MX53_PAD_CSI0_DAT14__IPU_CSI0_D_14 0x1d5 - MX53_PAD_CSI0_DAT13__IPU_CSI0_D_13 0x1d5 - MX53_PAD_CSI0_DAT12__IPU_CSI0_D_12 0x1d5 - MX53_PAD_CSI0_DAT11__IPU_CSI0_D_11 0x1d5 - MX53_PAD_CSI0_DAT10__IPU_CSI0_D_10 0x1d5 - MX53_PAD_CSI0_DAT9__IPU_CSI0_D_9 0x1d5 - MX53_PAD_CSI0_DAT8__IPU_CSI0_D_8 0x1d5 - MX53_PAD_CSI0_DAT7__IPU_CSI0_D_7 0x1d5 - MX53_PAD_CSI0_DAT6__IPU_CSI0_D_6 0x1d5 - MX53_PAD_CSI0_DAT5__IPU_CSI0_D_5 0x1d5 - MX53_PAD_CSI0_DAT4__IPU_CSI0_D_4 0x1d5 - MX53_PAD_CSI0_PIXCLK__IPU_CSI0_PIXCLK 0x1d5 - >; - }; - - pinctrl_csi_2: csigrp-2 { - fsl,pins = < - MX53_PAD_CSI0_VSYNC__IPU_CSI0_VSYNC 0x1d5 - MX53_PAD_CSI0_MCLK__IPU_CSI0_HSYNC 0x1d5 - MX53_PAD_CSI0_PIXCLK__IPU_CSI0_PIXCLK 0x1d5 - MX53_PAD_CSI0_DAT19__IPU_CSI0_D_19 0x1d5 - MX53_PAD_CSI0_DAT18__IPU_CSI0_D_18 0x1d5 - MX53_PAD_CSI0_DAT17__IPU_CSI0_D_17 0x1d5 - MX53_PAD_CSI0_DAT16__IPU_CSI0_D_16 0x1d5 - MX53_PAD_CSI0_DAT15__IPU_CSI0_D_15 0x1d5 - MX53_PAD_CSI0_DAT14__IPU_CSI0_D_14 0x1d5 - MX53_PAD_CSI0_DAT13__IPU_CSI0_D_13 0x1d5 - MX53_PAD_CSI0_DAT12__IPU_CSI0_D_12 0x1d5 - >; - }; - }; - - cspi { - pinctrl_cspi_1: cspigrp-1 { - fsl,pins = < - MX53_PAD_SD1_DATA0__CSPI_MISO 0x1d5 - MX53_PAD_SD1_CMD__CSPI_MOSI 0x1d5 - MX53_PAD_SD1_CLK__CSPI_SCLK 0x1d5 - >; - }; - - pinctrl_cspi_2: cspigrp-2 { - fsl,pins = < - MX53_PAD_EIM_D22__CSPI_MISO 0x1d5 - MX53_PAD_EIM_D28__CSPI_MOSI 0x1d5 - MX53_PAD_EIM_D21__CSPI_SCLK 0x1d5 - >; - }; - }; - - ecspi1 { - pinctrl_ecspi1_1: ecspi1grp-1 { - fsl,pins = < - MX53_PAD_EIM_D16__ECSPI1_SCLK 0x80000000 - MX53_PAD_EIM_D17__ECSPI1_MISO 0x80000000 - MX53_PAD_EIM_D18__ECSPI1_MOSI 0x80000000 - >; - }; - - pinctrl_ecspi1_2: ecspi1grp-2 { - fsl,pins = < - MX53_PAD_GPIO_19__ECSPI1_RDY 0x80000000 - MX53_PAD_EIM_EB2__ECSPI1_SS0 0x80000000 - MX53_PAD_EIM_D16__ECSPI1_SCLK 0x80000000 - MX53_PAD_EIM_D17__ECSPI1_MISO 0x80000000 - MX53_PAD_EIM_D18__ECSPI1_MOSI 0x80000000 - MX53_PAD_EIM_D19__ECSPI1_SS1 0x80000000 - >; - }; - }; - - ecspi2 { - pinctrl_ecspi2_1: ecspi2grp-1 { - fsl,pins = < - MX53_PAD_EIM_OE__ECSPI2_MISO 0x80000000 - MX53_PAD_EIM_CS1__ECSPI2_MOSI 0x80000000 - MX53_PAD_EIM_CS0__ECSPI2_SCLK 0x80000000 - >; - }; - }; - - esdhc1 { - pinctrl_esdhc1_1: esdhc1grp-1 { - fsl,pins = < - MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5 - MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5 - MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5 - MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5 - MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5 - MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5 - >; - }; - - pinctrl_esdhc1_2: esdhc1grp-2 { - fsl,pins = < - MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5 - MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5 - MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5 - MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5 - MX53_PAD_PATA_DATA8__ESDHC1_DAT4 0x1d5 - MX53_PAD_PATA_DATA9__ESDHC1_DAT5 0x1d5 - MX53_PAD_PATA_DATA10__ESDHC1_DAT6 0x1d5 - MX53_PAD_PATA_DATA11__ESDHC1_DAT7 0x1d5 - MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5 - MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5 - >; - }; - }; - - esdhc2 { - pinctrl_esdhc2_1: esdhc2grp-1 { - fsl,pins = < - MX53_PAD_SD2_CMD__ESDHC2_CMD 0x1d5 - MX53_PAD_SD2_CLK__ESDHC2_CLK 0x1d5 - MX53_PAD_SD2_DATA0__ESDHC2_DAT0 0x1d5 - MX53_PAD_SD2_DATA1__ESDHC2_DAT1 0x1d5 - MX53_PAD_SD2_DATA2__ESDHC2_DAT2 0x1d5 - MX53_PAD_SD2_DATA3__ESDHC2_DAT3 0x1d5 - >; - }; - }; - - esdhc3 { - pinctrl_esdhc3_1: esdhc3grp-1 { - fsl,pins = < - MX53_PAD_PATA_DATA8__ESDHC3_DAT0 0x1d5 - MX53_PAD_PATA_DATA9__ESDHC3_DAT1 0x1d5 - MX53_PAD_PATA_DATA10__ESDHC3_DAT2 0x1d5 - MX53_PAD_PATA_DATA11__ESDHC3_DAT3 0x1d5 - MX53_PAD_PATA_DATA0__ESDHC3_DAT4 0x1d5 - MX53_PAD_PATA_DATA1__ESDHC3_DAT5 0x1d5 - MX53_PAD_PATA_DATA2__ESDHC3_DAT6 0x1d5 - MX53_PAD_PATA_DATA3__ESDHC3_DAT7 0x1d5 - MX53_PAD_PATA_RESET_B__ESDHC3_CMD 0x1d5 - MX53_PAD_PATA_IORDY__ESDHC3_CLK 0x1d5 - >; - }; - }; - - can1 { - pinctrl_can1_1: can1grp-1 { - fsl,pins = < - MX53_PAD_PATA_INTRQ__CAN1_TXCAN 0x80000000 - MX53_PAD_PATA_DIOR__CAN1_RXCAN 0x80000000 - >; - }; - - pinctrl_can1_2: can1grp-2 { - fsl,pins = < - MX53_PAD_KEY_COL2__CAN1_TXCAN 0x80000000 - MX53_PAD_KEY_ROW2__CAN1_RXCAN 0x80000000 - >; - }; - - pinctrl_can1_3: can1grp-3 { - fsl,pins = < - MX53_PAD_GPIO_7__CAN1_TXCAN 0x80000000 - MX53_PAD_GPIO_8__CAN1_RXCAN 0x80000000 - >; - }; - }; - - can2 { - pinctrl_can2_1: can2grp-1 { - fsl,pins = < - MX53_PAD_KEY_COL4__CAN2_TXCAN 0x80000000 - MX53_PAD_KEY_ROW4__CAN2_RXCAN 0x80000000 - >; - }; - }; - - i2c1 { - pinctrl_i2c1_1: i2c1grp-1 { - fsl,pins = < - MX53_PAD_CSI0_DAT8__I2C1_SDA 0xc0000000 - MX53_PAD_CSI0_DAT9__I2C1_SCL 0xc0000000 - >; - }; - - pinctrl_i2c1_2: i2c1grp-2 { - fsl,pins = < - MX53_PAD_EIM_D21__I2C1_SCL 0xc0000000 - MX53_PAD_EIM_D28__I2C1_SDA 0xc0000000 - >; - }; - }; - - i2c2 { - pinctrl_i2c2_1: i2c2grp-1 { - fsl,pins = < - MX53_PAD_KEY_ROW3__I2C2_SDA 0xc0000000 - MX53_PAD_KEY_COL3__I2C2_SCL 0xc0000000 - >; - }; - - pinctrl_i2c2_2: i2c2grp-2 { - fsl,pins = < - MX53_PAD_EIM_D16__I2C2_SDA 0xc0000000 - MX53_PAD_EIM_EB2__I2C2_SCL 0xc0000000 - >; - }; - }; - - i2c3 { - pinctrl_i2c3_1: i2c3grp-1 { - fsl,pins = < - MX53_PAD_GPIO_6__I2C3_SDA 0xc0000000 - MX53_PAD_GPIO_5__I2C3_SCL 0xc0000000 - >; - }; - }; - - ipu_disp0 { - pinctrl_ipu_disp0_1: ipudisp0grp-1 { - fsl,pins = < - MX53_PAD_DI0_DISP_CLK__IPU_DI0_DISP_CLK 0x5 - MX53_PAD_DI0_PIN15__IPU_DI0_PIN15 0x5 - MX53_PAD_DI0_PIN2__IPU_DI0_PIN2 0x5 - MX53_PAD_DI0_PIN3__IPU_DI0_PIN3 0x5 - MX53_PAD_DISP0_DAT0__IPU_DISP0_DAT_0 0x5 - MX53_PAD_DISP0_DAT1__IPU_DISP0_DAT_1 0x5 - MX53_PAD_DISP0_DAT2__IPU_DISP0_DAT_2 0x5 - MX53_PAD_DISP0_DAT3__IPU_DISP0_DAT_3 0x5 - MX53_PAD_DISP0_DAT4__IPU_DISP0_DAT_4 0x5 - MX53_PAD_DISP0_DAT5__IPU_DISP0_DAT_5 0x5 - MX53_PAD_DISP0_DAT6__IPU_DISP0_DAT_6 0x5 - MX53_PAD_DISP0_DAT7__IPU_DISP0_DAT_7 0x5 - MX53_PAD_DISP0_DAT8__IPU_DISP0_DAT_8 0x5 - MX53_PAD_DISP0_DAT9__IPU_DISP0_DAT_9 0x5 - MX53_PAD_DISP0_DAT10__IPU_DISP0_DAT_10 0x5 - MX53_PAD_DISP0_DAT11__IPU_DISP0_DAT_11 0x5 - MX53_PAD_DISP0_DAT12__IPU_DISP0_DAT_12 0x5 - MX53_PAD_DISP0_DAT13__IPU_DISP0_DAT_13 0x5 - MX53_PAD_DISP0_DAT14__IPU_DISP0_DAT_14 0x5 - MX53_PAD_DISP0_DAT15__IPU_DISP0_DAT_15 0x5 - MX53_PAD_DISP0_DAT16__IPU_DISP0_DAT_16 0x5 - MX53_PAD_DISP0_DAT17__IPU_DISP0_DAT_17 0x5 - MX53_PAD_DISP0_DAT18__IPU_DISP0_DAT_18 0x5 - MX53_PAD_DISP0_DAT19__IPU_DISP0_DAT_19 0x5 - MX53_PAD_DISP0_DAT20__IPU_DISP0_DAT_20 0x5 - MX53_PAD_DISP0_DAT21__IPU_DISP0_DAT_21 0x5 - MX53_PAD_DISP0_DAT22__IPU_DISP0_DAT_22 0x5 - MX53_PAD_DISP0_DAT23__IPU_DISP0_DAT_23 0x5 - >; - }; - }; - - ipu_disp1 { - pinctrl_ipu_disp1_1: ipudisp1grp-1 { - fsl,pins = < - MX53_PAD_EIM_DA9__IPU_DISP1_DAT_0 0x5 - MX53_PAD_EIM_DA8__IPU_DISP1_DAT_1 0x5 - MX53_PAD_EIM_DA7__IPU_DISP1_DAT_2 0x5 - MX53_PAD_EIM_DA6__IPU_DISP1_DAT_3 0x5 - MX53_PAD_EIM_DA5__IPU_DISP1_DAT_4 0x5 - MX53_PAD_EIM_DA4__IPU_DISP1_DAT_5 0x5 - MX53_PAD_EIM_DA3__IPU_DISP1_DAT_6 0x5 - MX53_PAD_EIM_DA2__IPU_DISP1_DAT_7 0x5 - MX53_PAD_EIM_DA1__IPU_DISP1_DAT_8 0x5 - MX53_PAD_EIM_DA0__IPU_DISP1_DAT_9 0x5 - MX53_PAD_EIM_EB1__IPU_DISP1_DAT_10 0x5 - MX53_PAD_EIM_EB0__IPU_DISP1_DAT_11 0x5 - MX53_PAD_EIM_A17__IPU_DISP1_DAT_12 0x5 - MX53_PAD_EIM_A18__IPU_DISP1_DAT_13 0x5 - MX53_PAD_EIM_A19__IPU_DISP1_DAT_14 0x5 - MX53_PAD_EIM_A20__IPU_DISP1_DAT_15 0x5 - MX53_PAD_EIM_A21__IPU_DISP1_DAT_16 0x5 - MX53_PAD_EIM_A22__IPU_DISP1_DAT_17 0x5 - MX53_PAD_EIM_A23__IPU_DISP1_DAT_18 0x5 - MX53_PAD_EIM_A24__IPU_DISP1_DAT_19 0x5 - MX53_PAD_EIM_D31__IPU_DISP1_DAT_20 0x5 - MX53_PAD_EIM_D30__IPU_DISP1_DAT_21 0x5 - MX53_PAD_EIM_D26__IPU_DISP1_DAT_22 0x5 - MX53_PAD_EIM_D27__IPU_DISP1_DAT_23 0x5 - MX53_PAD_EIM_A16__IPU_DI1_DISP_CLK 0x5 - MX53_PAD_EIM_DA13__IPU_DI1_D0_CS 0x5 - MX53_PAD_EIM_DA14__IPU_DI1_D1_CS 0x5 - MX53_PAD_EIM_DA15__IPU_DI1_PIN1 0x5 - MX53_PAD_EIM_DA11__IPU_DI1_PIN2 0x5 - MX53_PAD_EIM_DA12__IPU_DI1_PIN3 0x5 - MX53_PAD_EIM_A25__IPU_DI1_PIN12 0x5 - MX53_PAD_EIM_DA10__IPU_DI1_PIN15 0x5 - >; - }; - }; - - ipu_disp2 { - pinctrl_ipu_disp2_1: ipudisp2grp-1 { - fsl,pins = < - MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0 0x80000000 - MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1 0x80000000 - MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2 0x80000000 - MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3 0x80000000 - MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK 0x80000000 - MX53_PAD_LVDS1_TX0_P__LDB_LVDS1_TX0 0x80000000 - MX53_PAD_LVDS1_TX1_P__LDB_LVDS1_TX1 0x80000000 - MX53_PAD_LVDS1_TX2_P__LDB_LVDS1_TX2 0x80000000 - MX53_PAD_LVDS1_TX3_P__LDB_LVDS1_TX3 0x80000000 - MX53_PAD_LVDS1_CLK_P__LDB_LVDS1_CLK 0x80000000 - >; - }; - }; - - nand { - pinctrl_nand_1: nandgrp-1 { - fsl,pins = < - MX53_PAD_NANDF_WE_B__EMI_NANDF_WE_B 0x4 - MX53_PAD_NANDF_RE_B__EMI_NANDF_RE_B 0x4 - MX53_PAD_NANDF_CLE__EMI_NANDF_CLE 0x4 - MX53_PAD_NANDF_ALE__EMI_NANDF_ALE 0x4 - MX53_PAD_NANDF_WP_B__EMI_NANDF_WP_B 0xe0 - MX53_PAD_NANDF_RB0__EMI_NANDF_RB_0 0xe0 - MX53_PAD_NANDF_CS0__EMI_NANDF_CS_0 0x4 - MX53_PAD_PATA_DATA0__EMI_NANDF_D_0 0xa4 - MX53_PAD_PATA_DATA1__EMI_NANDF_D_1 0xa4 - MX53_PAD_PATA_DATA2__EMI_NANDF_D_2 0xa4 - MX53_PAD_PATA_DATA3__EMI_NANDF_D_3 0xa4 - MX53_PAD_PATA_DATA4__EMI_NANDF_D_4 0xa4 - MX53_PAD_PATA_DATA5__EMI_NANDF_D_5 0xa4 - MX53_PAD_PATA_DATA6__EMI_NANDF_D_6 0xa4 - MX53_PAD_PATA_DATA7__EMI_NANDF_D_7 0xa4 - >; - }; - }; - - owire { - pinctrl_owire_1: owiregrp-1 { - fsl,pins = < - MX53_PAD_GPIO_18__OWIRE_LINE 0x80000000 - >; - }; - }; - - pwm1 { - pinctrl_pwm1_1: pwm1grp-1 { - fsl,pins = < - MX53_PAD_DISP0_DAT8__PWM1_PWMO 0x5 - >; - }; - }; - - pwm2 { - pinctrl_pwm2_1: pwm2grp-1 { - fsl,pins = < - MX53_PAD_GPIO_1__PWM2_PWMO 0x80000000 - >; - }; - }; - - uart1 { - pinctrl_uart1_1: uart1grp-1 { - fsl,pins = < - MX53_PAD_CSI0_DAT10__UART1_TXD_MUX 0x1e4 - MX53_PAD_CSI0_DAT11__UART1_RXD_MUX 0x1e4 - >; - }; - - pinctrl_uart1_2: uart1grp-2 { - fsl,pins = < - MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4 - MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4 - >; - }; - - pinctrl_uart1_3: uart1grp-3 { - fsl,pins = < - MX53_PAD_PATA_RESET_B__UART1_CTS 0x1c5 - MX53_PAD_PATA_IORDY__UART1_RTS 0x1c5 - >; - }; - }; - - uart2 { - pinctrl_uart2_1: uart2grp-1 { - fsl,pins = < - MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4 - MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4 - >; - }; - - pinctrl_uart2_2: uart2grp-2 { - fsl,pins = < - MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1c5 - MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1c5 - MX53_PAD_PATA_DIOR__UART2_RTS 0x1c5 - MX53_PAD_PATA_INTRQ__UART2_CTS 0x1c5 - >; - }; - }; - - uart3 { - pinctrl_uart3_1: uart3grp-1 { - fsl,pins = < - MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4 - MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4 - MX53_PAD_PATA_DA_1__UART3_CTS 0x1e4 - MX53_PAD_PATA_DA_2__UART3_RTS 0x1e4 - >; - }; - - pinctrl_uart3_2: uart3grp-2 { - fsl,pins = < - MX53_PAD_PATA_CS_0__UART3_TXD_MUX 0x1e4 - MX53_PAD_PATA_CS_1__UART3_RXD_MUX 0x1e4 - >; - }; - - }; - - uart4 { - pinctrl_uart4_1: uart4grp-1 { - fsl,pins = < - MX53_PAD_KEY_COL0__UART4_TXD_MUX 0x1e4 - MX53_PAD_KEY_ROW0__UART4_RXD_MUX 0x1e4 - >; - }; - }; - - uart5 { - pinctrl_uart5_1: uart5grp-1 { - fsl,pins = < - MX53_PAD_KEY_COL1__UART5_TXD_MUX 0x1e4 - MX53_PAD_KEY_ROW1__UART5_RXD_MUX 0x1e4 - >; - }; - }; }; gpr: iomuxc-gpr@53fa8000 { @@ -869,9 +402,12 @@ compatible = "fsl,imx53-ldb"; reg = <0x53fa8008 0x4>; gpr = <&gpr>; - clocks = <&clks 122>, <&clks 120>, - <&clks 115>, <&clks 116>, - <&clks 123>, <&clks 85>; + clocks = <&clks IMX5_CLK_LDB_DI0_SEL>, + <&clks IMX5_CLK_LDB_DI1_SEL>, + <&clks IMX5_CLK_IPU_DI0_SEL>, + <&clks IMX5_CLK_IPU_DI1_SEL>, + <&clks IMX5_CLK_LDB_DI0_GATE>, + <&clks IMX5_CLK_LDB_DI1_GATE>; clock-names = "di0_pll", "di1_pll", "di0_sel", "di1_sel", "di0", "di1"; @@ -904,7 +440,8 @@ #pwm-cells = <2>; compatible = "fsl,imx53-pwm", "fsl,imx27-pwm"; reg = <0x53fb4000 0x4000>; - clocks = <&clks 37>, <&clks 38>; + clocks = <&clks IMX5_CLK_PWM1_IPG_GATE>, + <&clks IMX5_CLK_PWM1_HF_GATE>; clock-names = "ipg", "per"; interrupts = <61>; }; @@ -913,7 +450,8 @@ #pwm-cells = <2>; compatible = "fsl,imx53-pwm", "fsl,imx27-pwm"; reg = <0x53fb8000 0x4000>; - clocks = <&clks 39>, <&clks 40>; + clocks = <&clks IMX5_CLK_PWM2_IPG_GATE>, + <&clks IMX5_CLK_PWM2_HF_GATE>; clock-names = "ipg", "per"; interrupts = <94>; }; @@ -922,7 +460,8 @@ compatible = "fsl,imx53-uart", "fsl,imx21-uart"; reg = <0x53fbc000 0x4000>; interrupts = <31>; - clocks = <&clks 28>, <&clks 29>; + clocks = <&clks IMX5_CLK_UART1_IPG_GATE>, + <&clks IMX5_CLK_UART1_PER_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -931,7 +470,8 @@ compatible = "fsl,imx53-uart", "fsl,imx21-uart"; reg = <0x53fc0000 0x4000>; interrupts = <32>; - clocks = <&clks 30>, <&clks 31>; + clocks = <&clks IMX5_CLK_UART2_IPG_GATE>, + <&clks IMX5_CLK_UART2_PER_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -940,7 +480,8 @@ compatible = "fsl,imx53-flexcan", "fsl,p1010-flexcan"; reg = <0x53fc8000 0x4000>; interrupts = <82>; - clocks = <&clks 158>, <&clks 157>; + clocks = <&clks IMX5_CLK_CAN1_IPG_GATE>, + <&clks IMX5_CLK_CAN1_SERIAL_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -949,7 +490,8 @@ compatible = "fsl,imx53-flexcan", "fsl,p1010-flexcan"; reg = <0x53fcc000 0x4000>; interrupts = <83>; - clocks = <&clks 87>, <&clks 86>; + clocks = <&clks IMX5_CLK_CAN2_IPG_GATE>, + <&clks IMX5_CLK_CAN2_SERIAL_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -1003,7 +545,7 @@ compatible = "fsl,imx53-i2c", "fsl,imx21-i2c"; reg = <0x53fec000 0x4000>; interrupts = <64>; - clocks = <&clks 88>; + clocks = <&clks IMX5_CLK_I2C3_GATE>; status = "disabled"; }; @@ -1011,7 +553,8 @@ compatible = "fsl,imx53-uart", "fsl,imx21-uart"; reg = <0x53ff0000 0x4000>; interrupts = <13>; - clocks = <&clks 65>, <&clks 66>; + clocks = <&clks IMX5_CLK_UART4_IPG_GATE>, + <&clks IMX5_CLK_UART4_PER_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -1028,14 +571,15 @@ compatible = "fsl,imx53-iim", "fsl,imx27-iim"; reg = <0x63f98000 0x4000>; interrupts = <69>; - clocks = <&clks 107>; + clocks = <&clks IMX5_CLK_IIM_GATE>; }; uart5: serial@63f90000 { compatible = "fsl,imx53-uart", "fsl,imx21-uart"; reg = <0x63f90000 0x4000>; interrupts = <86>; - clocks = <&clks 67>, <&clks 68>; + clocks = <&clks IMX5_CLK_UART5_IPG_GATE>, + <&clks IMX5_CLK_UART5_PER_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -1043,7 +587,7 @@ owire: owire@63fa4000 { compatible = "fsl,imx53-owire", "fsl,imx21-owire"; reg = <0x63fa4000 0x4000>; - clocks = <&clks 159>; + clocks = <&clks IMX5_CLK_OWIRE_GATE>; status = "disabled"; }; @@ -1053,7 +597,8 @@ compatible = "fsl,imx53-ecspi", "fsl,imx51-ecspi"; reg = <0x63fac000 0x4000>; interrupts = <37>; - clocks = <&clks 53>, <&clks 54>; + clocks = <&clks IMX5_CLK_ECSPI2_IPG_GATE>, + <&clks IMX5_CLK_ECSPI2_PER_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -1062,7 +607,8 @@ compatible = "fsl,imx53-sdma", "fsl,imx35-sdma"; reg = <0x63fb0000 0x4000>; interrupts = <6>; - clocks = <&clks 56>, <&clks 56>; + clocks = <&clks IMX5_CLK_SDMA_GATE>, + <&clks IMX5_CLK_SDMA_GATE>; clock-names = "ipg", "ahb"; #dma-cells = <3>; fsl,sdma-ram-script-name = "imx/sdma/sdma-imx53.bin"; @@ -1074,7 +620,8 @@ compatible = "fsl,imx53-cspi", "fsl,imx35-cspi"; reg = <0x63fc0000 0x4000>; interrupts = <38>; - clocks = <&clks 55>, <&clks 55>; + clocks = <&clks IMX5_CLK_CSPI_IPG_GATE>, + <&clks IMX5_CLK_CSPI_IPG_GATE>; clock-names = "ipg", "per"; status = "disabled"; }; @@ -1085,7 +632,7 @@ compatible = "fsl,imx53-i2c", "fsl,imx21-i2c"; reg = <0x63fc4000 0x4000>; interrupts = <63>; - clocks = <&clks 35>; + clocks = <&clks IMX5_CLK_I2C2_GATE>; status = "disabled"; }; @@ -1095,15 +642,16 @@ compatible = "fsl,imx53-i2c", "fsl,imx21-i2c"; reg = <0x63fc8000 0x4000>; interrupts = <62>; - clocks = <&clks 34>; + clocks = <&clks IMX5_CLK_I2C1_GATE>; status = "disabled"; }; ssi1: ssi@63fcc000 { - compatible = "fsl,imx53-ssi", "fsl,imx21-ssi"; + compatible = "fsl,imx53-ssi", "fsl,imx51-ssi", + "fsl,imx21-ssi"; reg = <0x63fcc000 0x4000>; interrupts = <29>; - clocks = <&clks 48>; + clocks = <&clks IMX5_CLK_SSI1_IPG_GATE>; dmas = <&sdma 28 0 0>, <&sdma 29 0 0>; dma-names = "rx", "tx"; @@ -1122,15 +670,16 @@ compatible = "fsl,imx53-nand"; reg = <0x63fdb000 0x1000 0xf7ff0000 0x10000>; interrupts = <8>; - clocks = <&clks 60>; + clocks = <&clks IMX5_CLK_NFC_GATE>; status = "disabled"; }; ssi3: ssi@63fe8000 { - compatible = "fsl,imx53-ssi", "fsl,imx21-ssi"; + compatible = "fsl,imx53-ssi", "fsl,imx51-ssi", + "fsl,imx21-ssi"; reg = <0x63fe8000 0x4000>; interrupts = <96>; - clocks = <&clks 50>; + clocks = <&clks IMX5_CLK_SSI3_IPG_GATE>; dmas = <&sdma 46 0 0>, <&sdma 47 0 0>; dma-names = "rx", "tx"; @@ -1143,7 +692,9 @@ compatible = "fsl,imx53-fec", "fsl,imx25-fec"; reg = <0x63fec000 0x4000>; interrupts = <87>; - clocks = <&clks 42>, <&clks 42>, <&clks 42>; + clocks = <&clks IMX5_CLK_FEC_GATE>, + <&clks IMX5_CLK_FEC_GATE>, + <&clks IMX5_CLK_FEC_GATE>; clock-names = "ipg", "ahb", "ptp"; status = "disabled"; }; @@ -1152,7 +703,8 @@ compatible = "fsl,imx53-tve"; reg = <0x63ff0000 0x1000>; interrupts = <92>; - clocks = <&clks 69>, <&clks 116>; + clocks = <&clks IMX5_CLK_TVE_GATE>, + <&clks IMX5_CLK_IPU_DI1_SEL>; clock-names = "tve", "di_sel"; status = "disabled"; @@ -1167,7 +719,8 @@ compatible = "fsl,imx53-vpu"; reg = <0x63ff4000 0x1000>; interrupts = <9>; - clocks = <&clks 63>, <&clks 63>; + clocks = <&clks IMX5_CLK_VPU_GATE>, + <&clks IMX5_CLK_VPU_GATE>; clock-names = "per", "ahb"; iram = <&ocram>; status = "disabled"; @@ -1177,7 +730,7 @@ ocram: sram@f8000000 { compatible = "mmio-sram"; reg = <0xf8000000 0x20000>; - clocks = <&clks 186>; + clocks = <&clks IMX5_CLK_OCRAM>; }; }; }; diff --git a/arch/arm/boot/dts/imx6dl-dfi-fs700-m60.dts b/arch/arm/boot/dts/imx6dl-dfi-fs700-m60.dts new file mode 100644 index 000000000000..994f96a3fb54 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-dfi-fs700-m60.dts @@ -0,0 +1,23 @@ +/* + * Copyright 2013 Sascha Hauer <s.hauer@pengutronix.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#ifndef __DTS_V1__ +#define __DTS_V1__ +/dts-v1/; +#endif + +#include "imx6dl.dtsi" +#include "imx6qdl-dfi-fs700-m60.dtsi" + +/ { + model = "DFI FS700-M60-6DL i.MX6dl Q7 Board"; + compatible = "dfi,fs700-m60-6dl", "dfi,fs700e-m60", "fsl,imx6dl"; +}; diff --git a/arch/arm/boot/dts/imx6dl-gw51xx.dts b/arch/arm/boot/dts/imx6dl-gw51xx.dts new file mode 100644 index 000000000000..4bd055f4c930 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-gw51xx.dts @@ -0,0 +1,19 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6dl.dtsi" +#include "imx6qdl-gw51xx.dtsi" + +/ { + model = "Gateworks Ventana i.MX6 DualLite GW51XX"; + compatible = "gw,imx6dl-gw51xx", "gw,ventana", "fsl,imx6dl"; +}; diff --git a/arch/arm/boot/dts/imx6dl-gw52xx.dts b/arch/arm/boot/dts/imx6dl-gw52xx.dts new file mode 100644 index 000000000000..c9136058f15e --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-gw52xx.dts @@ -0,0 +1,19 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6dl.dtsi" +#include "imx6qdl-gw52xx.dtsi" + +/ { + model = "Gateworks Ventana i.MX6 DualLite GW52XX"; + compatible = "gw,imx6dl-gw52xx", "gw,ventana", "fsl,imx6dl"; +}; diff --git a/arch/arm/boot/dts/imx6dl-gw53xx.dts b/arch/arm/boot/dts/imx6dl-gw53xx.dts new file mode 100644 index 000000000000..61818a14fde6 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-gw53xx.dts @@ -0,0 +1,19 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6dl.dtsi" +#include "imx6qdl-gw53xx.dtsi" + +/ { + model = "Gateworks Ventana i.MX6 DualLite GW53XX"; + compatible = "gw,imx6dl-gw53xx", "gw,ventana", "fsl,imx6dl"; +}; diff --git a/arch/arm/boot/dts/imx6dl-gw54xx.dts b/arch/arm/boot/dts/imx6dl-gw54xx.dts new file mode 100644 index 000000000000..ab38b6770a06 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-gw54xx.dts @@ -0,0 +1,19 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6dl.dtsi" +#include "imx6qdl-gw54xx.dtsi" + +/ { + model = "Gateworks Ventana i.MX6 DualLite GW54XX"; + compatible = "gw,imx6dl-gw54xx", "gw,ventana", "fsl,imx6dl"; +}; diff --git a/arch/arm/boot/dts/imx6dl-nitrogen6x.dts b/arch/arm/boot/dts/imx6dl-nitrogen6x.dts new file mode 100644 index 000000000000..5f4d33ccc4b3 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-nitrogen6x.dts @@ -0,0 +1,21 @@ +/* + * Copyright 2013 Boundary Devices, Inc. + * Copyright 2012 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6dl.dtsi" +#include "imx6qdl-nitrogen6x.dtsi" + +/ { + model = "Freescale i.MX6 DualLite Nitrogen6x Board"; + compatible = "fsl,imx6dl-nitrogen6x", "fsl,imx6dl"; +}; diff --git a/arch/arm/boot/dts/imx6dl-pinfunc.h b/arch/arm/boot/dts/imx6dl-pinfunc.h index b81a7a4ebab6..0ead323fdbd2 100644 --- a/arch/arm/boot/dts/imx6dl-pinfunc.h +++ b/arch/arm/boot/dts/imx6dl-pinfunc.h @@ -755,6 +755,7 @@ #define MX6QDL_PAD_GPIO_5__I2C3_SCL 0x230 0x600 0x878 0x6 0x2 #define MX6QDL_PAD_GPIO_5__ARM_EVENTI 0x230 0x600 0x000 0x7 0x0 #define MX6QDL_PAD_GPIO_6__ESAI_TX_CLK 0x234 0x604 0x840 0x0 0x1 +#define MX6QDL_PAD_GPIO_6__ENET_IRQ 0x234 0x604 0x03c 0x11 0xff000609 #define MX6QDL_PAD_GPIO_6__I2C3_SDA 0x234 0x604 0x87c 0x2 0x2 #define MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x234 0x604 0x000 0x5 0x0 #define MX6QDL_PAD_GPIO_6__SD2_LCTL 0x234 0x604 0x000 0x6 0x0 @@ -950,6 +951,7 @@ #define MX6QDL_PAD_RGMII_TXC__GPIO6_IO19 0x2d8 0x6c0 0x000 0x5 0x0 #define MX6QDL_PAD_RGMII_TXC__XTALOSC_REF_CLK_24M 0x2d8 0x6c0 0x000 0x7 0x0 #define MX6QDL_PAD_SD1_CLK__SD1_CLK 0x2dc 0x6c4 0x928 0x0 0x1 +#define MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT 0x2dc 0x6c4 0x000 0x2 0x0 #define MX6QDL_PAD_SD1_CLK__GPT_CLKIN 0x2dc 0x6c4 0x000 0x3 0x0 #define MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x2dc 0x6c4 0x000 0x5 0x0 #define MX6QDL_PAD_SD1_CMD__SD1_CMD 0x2e0 0x6c8 0x000 0x0 0x0 diff --git a/arch/arm/boot/dts/imx6dl-sabrelite.dts b/arch/arm/boot/dts/imx6dl-sabrelite.dts new file mode 100644 index 000000000000..2de04479dc35 --- /dev/null +++ b/arch/arm/boot/dts/imx6dl-sabrelite.dts @@ -0,0 +1,20 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6dl.dtsi" +#include "imx6qdl-sabrelite.dtsi" + +/ { + model = "Freescale i.MX6 DualLite SABRE Lite Board"; + compatible = "fsl,imx6dl-sabrelite", "fsl,imx6dl"; +}; diff --git a/arch/arm/boot/dts/imx6dl.dtsi b/arch/arm/boot/dts/imx6dl.dtsi index 25bbdd6f214b..5c5f574330f9 100644 --- a/arch/arm/boot/dts/imx6dl.dtsi +++ b/arch/arm/boot/dts/imx6dl.dtsi @@ -8,6 +8,7 @@ * */ +#include <dt-bindings/interrupt-controller/irq.h> #include "imx6dl-pinfunc.h" #include "imx6qdl.dtsi" @@ -21,6 +22,26 @@ device_type = "cpu"; reg = <0>; next-level-cache = <&L2>; + operating-points = < + /* kHz uV */ + 996000 1275000 + 792000 1175000 + 396000 1075000 + >; + fsl,soc-operating-points = < + /* ARM kHz SOC-PU uV */ + 996000 1175000 + 792000 1175000 + 396000 1175000 + >; + clock-latency = <61036>; /* two CLK32 periods */ + clocks = <&clks 104>, <&clks 6>, <&clks 16>, + <&clks 17>, <&clks 170>; + clock-names = "arm", "pll2_pfd2_396m", "step", + "pll1_sw", "pll1_sys"; + arm-supply = <®_arm>; + pu-supply = <®_pu>; + soc-supply = <®_soc>; }; cpu@1 { @@ -45,17 +66,17 @@ pxp: pxp@020f0000 { reg = <0x020f0000 0x4000>; - interrupts = <0 98 0x04>; + interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>; }; epdc: epdc@020f4000 { reg = <0x020f4000 0x4000>; - interrupts = <0 97 0x04>; + interrupts = <0 97 IRQ_TYPE_LEVEL_HIGH>; }; lcdif: lcdif@020f8000 { reg = <0x020f8000 0x4000>; - interrupts = <0 39 0x04>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; }; }; @@ -65,7 +86,7 @@ #size-cells = <0>; compatible = "fsl,imx1-i2c"; reg = <0x021f8000 0x4000>; - interrupts = <0 35 0x04>; + interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>; status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/imx6q-arm2.dts b/arch/arm/boot/dts/imx6q-arm2.dts index edf1bd967164..78df05e9d1ce 100644 --- a/arch/arm/boot/dts/imx6q-arm2.dts +++ b/arch/arm/boot/dts/imx6q-arm2.dts @@ -23,14 +23,27 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_3p3v: 3p3v { + reg_3p3v: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "3P3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; }; + + reg_usb_otg_vbus: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 0>; + enable-active-high; + }; }; leds { @@ -46,7 +59,7 @@ &gpmi { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gpmi_nand_1>; + pinctrl-0 = <&pinctrl_gpmi_nand>; status = "disabled"; /* gpmi nand conflicts with SD */ }; @@ -54,28 +67,131 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; - hog { + imx6q-arm2 { pinctrl_hog: hoggrp { fsl,pins = < MX6QDL_PAD_EIM_D25__GPIO3_IO25 0x80000000 >; }; - }; - arm2 { - pinctrl_usdhc3_arm2: usdhc3grp-arm2 { + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_KEY_COL2__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1 + >; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 + MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1 + MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059 + >; + }; + + pinctrl_usdhc3_cdwp: usdhc3cdwp { fsl,pins = < MX6QDL_PAD_NANDF_CS0__GPIO6_IO11 0x80000000 MX6QDL_PAD_NANDF_CS1__GPIO6_IO14 0x80000000 >; }; + + pinctrl_usdhc4: usdhc4grp { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059 + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059 + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059 + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059 + >; + }; }; }; &fec { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_enet_2>; + pinctrl-0 = <&pinctrl_enet>; phy-mode = "rgmii"; + interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>, + <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; status = "okay"; }; @@ -84,8 +200,8 @@ wp-gpios = <&gpio6 14 0>; vmmc-supply = <®_3p3v>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc3_1 - &pinctrl_usdhc3_arm2>; + pinctrl-0 = <&pinctrl_usdhc3 + &pinctrl_usdhc3_cdwp>; status = "okay"; }; @@ -93,13 +209,13 @@ non-removable; vmmc-supply = <®_3p3v>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc4_1>; + pinctrl-0 = <&pinctrl_usdhc4>; status = "okay"; }; &uart2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2_2>; + pinctrl-0 = <&pinctrl_uart2>; fsl,dte-mode; fsl,uart-has-rtscts; status = "okay"; @@ -107,6 +223,6 @@ &uart4 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart4_1>; + pinctrl-0 = <&pinctrl_uart4>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6q-cm-fx6.dts b/arch/arm/boot/dts/imx6q-cm-fx6.dts new file mode 100644 index 000000000000..99b46f8030ad --- /dev/null +++ b/arch/arm/boot/dts/imx6q-cm-fx6.dts @@ -0,0 +1,107 @@ +/* + * Copyright 2013 CompuLab Ltd. + * + * Author: Valentin Raevsky <valentin@compulab.co.il> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" + +/ { + model = "CompuLab CM-FX6"; + compatible = "compulab,cm-fx6", "fsl,imx6q"; + + memory { + reg = <0x10000000 0x80000000>; + }; + + leds { + compatible = "gpio-leds"; + + heartbeat-led { + label = "Heartbeat"; + gpios = <&gpio2 31 0>; + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand>; + status = "okay"; +}; + +&iomuxc { + imx6q-cm-fx6 { + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + >; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 + MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + }; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-dfi-fs700-m60.dts b/arch/arm/boot/dts/imx6q-dfi-fs700-m60.dts new file mode 100644 index 000000000000..fd0ad9a8866c --- /dev/null +++ b/arch/arm/boot/dts/imx6q-dfi-fs700-m60.dts @@ -0,0 +1,23 @@ +/* + * Copyright 2013 Sascha Hauer <s.hauer@pengutronix.de> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +#ifndef __DTS_V1__ +#define __DTS_V1__ +/dts-v1/; +#endif + +#include "imx6q.dtsi" +#include "imx6qdl-dfi-fs700-m60.dtsi" + +/ { + model = "DFI FS700-M60-6QD i.MX6qd Q7 Board"; + compatible = "dfi,fs700-m60-6qd", "dfi,fs700e-m60", "fsl,imx6q"; +}; diff --git a/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts new file mode 100644 index 000000000000..a63bbb3d46bb --- /dev/null +++ b/arch/arm/boot/dts/imx6q-dmo-edmqmx6.dts @@ -0,0 +1,372 @@ +/* + * Copyright 2013 Data Modul AG + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include "imx6q.dtsi" + +/ { + model = "Data Modul eDM-QMX6 Board"; + compatible = "dmo,imx6q-edmqmx6", "fsl,imx6q"; + + aliases { + gpio7 = &stmpe_gpio; + }; + + memory { + reg = <0x10000000 0x80000000>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_3p3v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_otg_vbus: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio7 12 0>; + }; + + reg_usb_host1: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "usb_host1_en"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio3 31 0>; + enable-active-high; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + + led-blue { + label = "blue"; + gpios = <&stmpe_gpio 8 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + led-green { + label = "green"; + gpios = <&stmpe_gpio 9 GPIO_ACTIVE_HIGH>; + }; + + led-pink { + label = "pink"; + gpios = <&stmpe_gpio 10 GPIO_ACTIVE_HIGH>; + }; + + led-red { + label = "red"; + gpios = <&stmpe_gpio 11 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio3 23 0>; + phy-supply = <&vgen2_1v2_eth>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2 + &pinctrl_stmpe>; + status = "okay"; + + pmic: pfuze100@08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + interrupt-parent = <&gpio3>; + interrupts = <20 8>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-always-on; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + regulator-always-on; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_1v2_eth: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vdd_high_in: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; + + stmpe: stmpe1601@40 { + compatible = "st,stmpe1601"; + reg = <0x40>; + interrupts = <30 0>; + interrupt-parent = <&gpio3>; + + stmpe_gpio: stmpe_gpio { + #gpio-cells = <2>; + compatible = "st,stmpe-gpio"; + }; + }; + + temp1: ad7414@4c { + compatible = "ad,ad7414"; + reg = <0x4c>; + }; + + temp2: ad7414@4d { + compatible = "ad,ad7414"; + reg = <0x4d>; + }; + + rtc: m41t62@68 { + compatible = "stm,m41t62"; + reg = <0x68>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6q-dmo-edmqmx6 { + pinctrl_hog: hoggrp { + fsl,pins = < + MX6QDL_PAD_EIM_A16__GPIO2_IO22 0x80000000 + MX6QDL_PAD_EIM_A17__GPIO2_IO21 0x80000000 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_stmpe: stmpegrp { + fsl,pins = <MX6QDL_PAD_EIM_D30__GPIO3_IO30 0x80000000>; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + >; + }; + + pinctrl_usdhc4: usdhc4grp { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059 + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059 + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059 + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059 + >; + }; + }; +}; + +&sata { + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usb_host1>; + disable-over-current; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; + +&usdhc4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc4>; + vmmc-supply = <®_3p3v>; + non-removable; + bus-width = <8>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-gk802.dts b/arch/arm/boot/dts/imx6q-gk802.dts new file mode 100644 index 000000000000..4a9b4dc9afc0 --- /dev/null +++ b/arch/arm/boot/dts/imx6q-gk802.dts @@ -0,0 +1,171 @@ +/* + * Copyright (C) 2013 Philipp Zabel + * + * This file is licensed under the terms of the GNU General Public License + * version 2. This program is licensed "as is" without any warranty of any + * kind, whether express or implied. + */ + +/dts-v1/; +#include "imx6q.dtsi" + +/ { + model = "Zealz GK802"; + compatible = "zealz,imx6q-gk802", "fsl,imx6q"; + + chosen { + linux,stdout-path = &uart4; + }; + + memory { + reg = <0x10000000 0x40000000>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_3p3v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + recovery-button { + label = "recovery"; + gpios = <&gpio3 16 1>; + linux,code = <0x198>; /* KEY_RESTART */ + gpio-key,wakeup; + }; + }; +}; + +/* Internal I2C */ +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + clock-frequency = <100000>; + status = "okay"; + + /* SDMC DM2016 1024 bit EEPROM + 128 bit OTP */ + eeprom: dm2016@51 { + compatible = "sdmc,dm2016"; + reg = <0x51>; + }; +}; + +/* External I2C via HDMI */ +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + clock-frequency = <100000>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6q-gk802 { + pinctrl_hog: hoggrp { + fsl,pins = < + /* Recovery button, active-low */ + MX6QDL_PAD_EIM_D16__GPIO3_IO16 0x100b1 + /* RTL8192CU enable GPIO, active-low */ + MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x1b0b0 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + >; + }; + + pinctrl_usdhc4: usdhc4grp { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 + >; + }; + }; +}; + +&uart2 { + status = "okay"; +}; + +&uart4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart4>; + status = "okay"; +}; + +/* External USB-A port (USBOTG) */ +&usbotg { + disable-over-current; + status = "okay"; +}; + +/* Internal USB port (USBH1), connected to RTL8192CU */ +&usbh1 { + disable-over-current; + status = "okay"; +}; + +/* External microSD */ +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + bus-width = <4>; + cd-gpios = <&gpio6 11 0>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; + +/* Internal microSD */ +&usdhc4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc4>; + bus-width = <4>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-gw51xx.dts b/arch/arm/boot/dts/imx6q-gw51xx.dts new file mode 100644 index 000000000000..af4929aee075 --- /dev/null +++ b/arch/arm/boot/dts/imx6q-gw51xx.dts @@ -0,0 +1,19 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include "imx6qdl-gw54xx.dtsi" + +/ { + model = "Gateworks Ventana i.MX6 Quad GW51XX"; + compatible = "gw,imx6q-gw51xx", "gw,ventana", "fsl,imx6q"; +}; diff --git a/arch/arm/boot/dts/imx6q-gw52xx.dts b/arch/arm/boot/dts/imx6q-gw52xx.dts new file mode 100644 index 000000000000..5f71ddbc7f05 --- /dev/null +++ b/arch/arm/boot/dts/imx6q-gw52xx.dts @@ -0,0 +1,23 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include "imx6qdl-gw52xx.dtsi" + +/ { + model = "Gateworks Ventana i.MX6 Quad GW52XX"; + compatible = "gw,imx6q-gw52xx", "gw,ventana", "fsl,imx6q"; +}; + +&sata { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-gw53xx.dts b/arch/arm/boot/dts/imx6q-gw53xx.dts new file mode 100644 index 000000000000..360c316b4740 --- /dev/null +++ b/arch/arm/boot/dts/imx6q-gw53xx.dts @@ -0,0 +1,23 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include "imx6qdl-gw53xx.dtsi" + +/ { + model = "Gateworks Ventana i.MX6 Quad GW53XX"; + compatible = "gw,imx6q-gw53xx", "gw,ventana", "fsl,imx6q"; +}; + +&sata { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-gw5400-a.dts b/arch/arm/boot/dts/imx6q-gw5400-a.dts new file mode 100644 index 000000000000..902f98310481 --- /dev/null +++ b/arch/arm/boot/dts/imx6q-gw5400-a.dts @@ -0,0 +1,546 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" + +/ { + model = "Gateworks Ventana GW5400-A"; + compatible = "gw,imx6q-gw5400-a", "gw,ventana", "fsl,imx6q"; + + /* these are used by bootloader for disabling nodes */ + aliases { + ethernet0 = &fec; + ethernet1 = ð1; + i2c0 = &i2c1; + i2c1 = &i2c2; + i2c2 = &i2c3; + led0 = &led0; + led1 = &led1; + led2 = &led2; + sky2 = ð1; + ssi0 = &ssi1; + spi0 = &ecspi1; + usb0 = &usbh1; + usb1 = &usbotg; + usdhc2 = &usdhc3; + }; + + chosen { + bootargs = "console=ttymxc1,115200"; + }; + + leds { + compatible = "gpio-leds"; + + led0: user1 { + label = "user1"; + gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */ + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + led1: user2 { + label = "user2"; + gpios = <&gpio4 10 0>; /* 106 -> MX6_PANLEDR */ + default-state = "off"; + }; + + led2: user3 { + label = "user3"; + gpios = <&gpio4 15 1>; /* 111 -> MX6_LOCLED# */ + default-state = "off"; + }; + }; + + memory { + reg = <0x10000000 0x40000000>; + }; + + pps { + compatible = "pps-gpio"; + gpios = <&gpio1 5 0>; + status = "okay"; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_1p0v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "1P0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + reg_3p3v: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_h1_vbus: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "usb_h1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + reg_usb_otg_vbus: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 0>; + enable-active-high; + }; + }; + + sound { + compatible = "fsl,imx6q-sabrelite-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "imx6q-sabrelite-sgtl5000"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-int-port = <1>; + mux-ext-port = <4>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&ecspi1 { + fsl,spi-num-chipselects = <1>; + cs-gpios = <&gpio3 19 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash: m25p80@0 { + compatible = "sst,w25q256"; + spi-max-frequency = <30000000>; + reg = <0>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 30 0>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + eeprom1: eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + + eeprom2: eeprom@51 { + compatible = "atmel,24c02"; + reg = <0x51>; + pagesize = <16>; + }; + + eeprom3: eeprom@52 { + compatible = "atmel,24c02"; + reg = <0x52>; + pagesize = <16>; + }; + + eeprom4: eeprom@53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; + + gpio: pca9555@23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + }; + + hwmon: gsc@29 { + compatible = "gw,gsp"; + reg = <0x29>; + }; + + rtc: ds1672@68 { + compatible = "dallas,ds1672"; + reg = <0x68>; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pmic: pfuze100@08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3950000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; + + pciswitch: pex8609@3f { + compatible = "plx,pex8609"; + reg = <0x3f>; + }; + + pciclkgen: si52147@6b { + compatible = "sil,si52147"; + reg = <0x6b>; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + accelerometer: mma8450@1c { + compatible = "fsl,mma8450"; + reg = <0x1c>; + }; + + codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + clocks = <&clks 201>; + VDDA-supply = <&sw4_reg>; + VDDIO-supply = <®_3p3v>; + }; + + hdmiin: adv7611@4c { + compatible = "adi,adv7611"; + reg = <0x4c>; + }; + + touchscreen: egalax_ts@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio7>; + interrupts = <12 2>; /* gpio7_12 active low */ + wakeup-gpios = <&gpio7 12 0>; + }; + + videoout: adv7393@2a { + compatible = "adi,adv7393"; + reg = <0x2a>; + }; + + videoin: adv7180@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6q-gw5400-a { + pinctrl_hog: hoggrp { + fsl,pins = < + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x80000000 /* OTG_PWR_EN */ + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x80000000 /* SPINOR_CS0# */ + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x80000000 /* PCIE IRQ */ + MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 /* PCIE RST */ + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000130b0 /* AUD4_MCK */ + MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x80000000 /* GPS_PPS */ + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000 /* TOUCH_IRQ# */ + MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x80000000 /* user1 led */ + MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x80000000 /* user2 led */ + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x80000000 /* user3 led */ + MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x80000000 /* USBHUB_RST# */ + MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x80000000 /* MIPI_DIO */ + >; + }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x130b0 + MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x130b0 + MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x110b0 + MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x130b0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + >; + }; + }; +}; + +&ldb { + status = "okay"; + lvds-channel@0 { + crtcs = <&ipu1 0>, <&ipu1 1>, <&ipu2 0>, <&ipu2 1>; + }; +}; + +&pcie { + reset-gpio = <&gpio1 29 0>; + status = "okay"; + + eth1: sky2@8 { /* MAC/PHY on bus 8 */ + compatible = "marvell,sky2"; + }; +}; + +&ssi1 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usb_h1_vbus>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + cd-gpios = <&gpio7 0 0>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-gw54xx.dts b/arch/arm/boot/dts/imx6q-gw54xx.dts new file mode 100644 index 000000000000..ab518d66a75e --- /dev/null +++ b/arch/arm/boot/dts/imx6q-gw54xx.dts @@ -0,0 +1,23 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include "imx6qdl-gw54xx.dtsi" + +/ { + model = "Gateworks Ventana i.MX6 Quad GW54XX"; + compatible = "gw,imx6q-gw54xx", "gw,ventana", "fsl,imx6q"; +}; + +&sata { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-nitrogen6x.dts b/arch/arm/boot/dts/imx6q-nitrogen6x.dts new file mode 100644 index 000000000000..a57866b2e97e --- /dev/null +++ b/arch/arm/boot/dts/imx6q-nitrogen6x.dts @@ -0,0 +1,25 @@ +/* + * Copyright 2013 Boundary Devices, Inc. + * Copyright 2012 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +#include "imx6q.dtsi" +#include "imx6qdl-nitrogen6x.dtsi" + +/ { + model = "Freescale i.MX6 Quad Nitrogen6x Board"; + compatible = "fsl,imx6q-nitrogen6x", "fsl,imx6q"; +}; + +&sata { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6q-phytec-pbab01.dts b/arch/arm/boot/dts/imx6q-phytec-pbab01.dts index 7d37ec60d58d..5607c331fca8 100644 --- a/arch/arm/boot/dts/imx6q-phytec-pbab01.dts +++ b/arch/arm/boot/dts/imx6q-phytec-pbab01.dts @@ -21,10 +21,26 @@ status = "okay"; }; +&gpmi { + status = "okay"; +}; + +&sata { + status = "okay"; +}; + &uart4 { status = "okay"; }; +&usbh1 { + status = "okay"; +}; + +&usbotg { + status = "okay"; +}; + &usdhc2 { status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6q-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6q-phytec-pfla02.dtsi index 1a3b50d4d8fa..324f1550976b 100644 --- a/arch/arm/boot/dts/imx6q-phytec-pfla02.dtsi +++ b/arch/arm/boot/dts/imx6q-phytec-pfla02.dtsi @@ -18,11 +18,35 @@ memory { reg = <0x10000000 0x80000000>; }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_usb_otg_vbus: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio4 15 0>; + }; + + reg_usb_h1_vbus: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "usb_h1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 0 0>; + }; + }; }; &ecspi3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi3_1>; + pinctrl-0 = <&pinctrl_ecspi3>; status = "okay"; fsl,spi-num-chipselects = <1>; cs-gpios = <&gpio4 24 0>; @@ -36,7 +60,7 @@ &i2c1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1_1>; + pinctrl-0 = <&pinctrl_i2c1>; status = "okay"; eeprom@50 { @@ -128,7 +152,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; - hog { + imx6q-phytec-pfla02 { pinctrl_hog: hoggrp { fsl,pins = < MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x80000000 @@ -136,10 +160,109 @@ MX6QDL_PAD_DI0_PIN15__GPIO4_IO17 0x80000000 /* PMIC interrupt */ >; }; - }; - pfla02 { - pinctrl_usdhc3_pfla02: usdhc3grp-pfla02 { + pinctrl_ecspi3: ecspi3grp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1 + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1 + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 + >; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 + MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbh1: usbh1grp { + fsl,pins = < + MX6QDL_PAD_GPIO_0__USB_H1_PWR 0x80000000 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0 + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x80000000 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + >; + }; + + pinctrl_usdhc3_cdwp: usdhc3cdwp { fsl,pins = < MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x80000000 MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 @@ -150,21 +273,43 @@ &fec { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_enet_3>; + pinctrl-0 = <&pinctrl_enet>; phy-mode = "rgmii"; phy-reset-gpios = <&gpio3 23 0>; status = "disabled"; }; +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand>; + nand-on-flash-bbt; + status = "disabled"; +}; + &uart4 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart4_1>; + pinctrl-0 = <&pinctrl_uart4>; + status = "disabled"; +}; + +&usbh1 { + vbus-supply = <®_usb_h1_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbh1>; + status = "disabled"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; status = "disabled"; }; &usdhc2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc2_2>; + pinctrl-0 = <&pinctrl_usdhc2>; cd-gpios = <&gpio1 4 0>; wp-gpios = <&gpio1 2 0>; status = "disabled"; @@ -172,8 +317,8 @@ &usdhc3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc3_2 - &pinctrl_usdhc3_pfla02>; + pinctrl-0 = <&pinctrl_usdhc3 + &pinctrl_usdhc3_cdwp>; cd-gpios = <&gpio1 27 0>; wp-gpios = <&gpio1 29 0>; status = "disabled"; diff --git a/arch/arm/boot/dts/imx6q-pinfunc.h b/arch/arm/boot/dts/imx6q-pinfunc.h index 97ed0816a6e0..9fc6120a1853 100644 --- a/arch/arm/boot/dts/imx6q-pinfunc.h +++ b/arch/arm/boot/dts/imx6q-pinfunc.h @@ -673,6 +673,7 @@ #define MX6QDL_PAD_GPIO_3__USB_H1_OC 0x22c 0x5fc 0x948 0x6 0x1 #define MX6QDL_PAD_GPIO_3__MLB_CLK 0x22c 0x5fc 0x900 0x7 0x1 #define MX6QDL_PAD_GPIO_6__ESAI_TX_CLK 0x230 0x600 0x870 0x0 0x1 +#define MX6QDL_PAD_GPIO_6__ENET_IRQ 0x230 0x600 0x03c 0x11 0xff000609 #define MX6QDL_PAD_GPIO_6__I2C3_SDA 0x230 0x600 0x8ac 0x2 0x1 #define MX6QDL_PAD_GPIO_6__GPIO1_IO06 0x230 0x600 0x000 0x5 0x0 #define MX6QDL_PAD_GPIO_6__SD2_LCTL 0x230 0x600 0x000 0x6 0x0 @@ -1024,6 +1025,7 @@ #define MX6QDL_PAD_SD1_DAT2__WDOG1_RESET_B_DEB 0x34c 0x734 0x000 0x6 0x0 #define MX6QDL_PAD_SD1_CLK__SD1_CLK 0x350 0x738 0x000 0x0 0x0 #define MX6QDL_PAD_SD1_CLK__ECSPI5_SCLK 0x350 0x738 0x828 0x1 0x0 +#define MX6QDL_PAD_SD1_CLK__OSC32K_32K_OUT 0x350 0x738 0x000 0x2 0x0 #define MX6QDL_PAD_SD1_CLK__GPT_CLKIN 0x350 0x738 0x000 0x3 0x0 #define MX6QDL_PAD_SD1_CLK__GPIO1_IO20 0x350 0x738 0x000 0x5 0x0 #define MX6QDL_PAD_SD2_CLK__SD2_CLK 0x354 0x73c 0x000 0x0 0x0 diff --git a/arch/arm/boot/dts/imx6q-sabrelite.dts b/arch/arm/boot/dts/imx6q-sabrelite.dts index f004913f7d80..96e4688be77c 100644 --- a/arch/arm/boot/dts/imx6q-sabrelite.dts +++ b/arch/arm/boot/dts/imx6q-sabrelite.dts @@ -12,189 +12,13 @@ /dts-v1/; #include "imx6q.dtsi" +#include "imx6qdl-sabrelite.dtsi" / { model = "Freescale i.MX6 Quad SABRE Lite Board"; compatible = "fsl,imx6q-sabrelite", "fsl,imx6q"; - - memory { - reg = <0x10000000 0x40000000>; - }; - - regulators { - compatible = "simple-bus"; - - reg_2p5v: 2p5v { - compatible = "regulator-fixed"; - regulator-name = "2P5V"; - regulator-min-microvolt = <2500000>; - regulator-max-microvolt = <2500000>; - regulator-always-on; - }; - - reg_3p3v: 3p3v { - compatible = "regulator-fixed"; - regulator-name = "3P3V"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - reg_usb_otg_vbus: usb_otg_vbus { - compatible = "regulator-fixed"; - regulator-name = "usb_otg_vbus"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - gpio = <&gpio3 22 0>; - enable-active-high; - }; - }; - - sound { - compatible = "fsl,imx6q-sabrelite-sgtl5000", - "fsl,imx-audio-sgtl5000"; - model = "imx6q-sabrelite-sgtl5000"; - ssi-controller = <&ssi1>; - audio-codec = <&codec>; - audio-routing = - "MIC_IN", "Mic Jack", - "Mic Jack", "Mic Bias", - "Headphone Jack", "HP_OUT"; - mux-int-port = <1>; - mux-ext-port = <4>; - }; -}; - -&audmux { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_audmux_1>; -}; - -&ecspi1 { - fsl,spi-num-chipselects = <1>; - cs-gpios = <&gpio3 19 0>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi1_1>; - status = "okay"; - - flash: m25p80@0 { - compatible = "sst,sst25vf016b"; - spi-max-frequency = <20000000>; - reg = <0>; - }; -}; - -&fec { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_enet_1>; - phy-mode = "rgmii"; - phy-reset-gpios = <&gpio3 23 0>; - status = "okay"; -}; - -&i2c1 { - status = "okay"; - clock-frequency = <100000>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1_1>; - - codec: sgtl5000@0a { - compatible = "fsl,sgtl5000"; - reg = <0x0a>; - clocks = <&clks 201>; - VDDA-supply = <®_2p5v>; - VDDIO-supply = <®_3p3v>; - }; -}; - -&iomuxc { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_hog>; - - hog { - pinctrl_hog: hoggrp { - fsl,pins = < - MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x80000000 - MX6QDL_PAD_NANDF_D7__GPIO2_IO07 0x80000000 - MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x80000000 - MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x80000000 - MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x80000000 - MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x80000000 - MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1f0b0 - MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x80000000 - MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x80000000 - >; - }; - }; -}; - -&ldb { - status = "okay"; - - lvds-channel@0 { - fsl,data-mapping = "spwg"; - fsl,data-width = <18>; - status = "okay"; - - display-timings { - native-mode = <&timing0>; - timing0: hsd100pxn1 { - clock-frequency = <65000000>; - hactive = <1024>; - vactive = <768>; - hback-porch = <220>; - hfront-porch = <40>; - vback-porch = <21>; - vfront-porch = <7>; - hsync-len = <60>; - vsync-len = <10>; - }; - }; - }; }; &sata { status = "okay"; }; - -&ssi1 { - fsl,mode = "i2s-slave"; - status = "okay"; -}; - -&uart2 { - status = "okay"; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2_1>; -}; - -&usbh1 { - status = "okay"; -}; - -&usbotg { - vbus-supply = <®_usb_otg_vbus>; - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usbotg_1>; - disable-over-current; - status = "okay"; -}; - -&usdhc3 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc3_2>; - cd-gpios = <&gpio7 0 0>; - wp-gpios = <&gpio7 1 0>; - vmmc-supply = <®_3p3v>; - status = "okay"; -}; - -&usdhc4 { - pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc4_2>; - cd-gpios = <&gpio2 6 0>; - wp-gpios = <&gpio2 7 0>; - vmmc-supply = <®_3p3v>; - status = "okay"; -}; diff --git a/arch/arm/boot/dts/imx6q-sbc6x.dts b/arch/arm/boot/dts/imx6q-sbc6x.dts index ee6addf149af..86cf09364664 100644 --- a/arch/arm/boot/dts/imx6q-sbc6x.dts +++ b/arch/arm/boot/dts/imx6q-sbc6x.dts @@ -17,28 +17,78 @@ }; }; + &fec { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_enet_1>; + pinctrl-0 = <&pinctrl_enet>; phy-mode = "rgmii"; status = "okay"; }; +&iomuxc { + imx6q-sbc6x { + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + >; + }; + }; +}; + &uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_1>; + pinctrl-0 = <&pinctrl_uart1>; status = "okay"; }; &usbotg { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usbotg_1>; + pinctrl-0 = <&pinctrl_usbotg>; disable-over-current; status = "okay"; }; &usdhc3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc3_2>; + pinctrl-0 = <&pinctrl_usdhc3>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6q-udoo.dts b/arch/arm/boot/dts/imx6q-udoo.dts index 6e1ccdc019a7..ed397d149ab6 100644 --- a/arch/arm/boot/dts/imx6q-udoo.dts +++ b/arch/arm/boot/dts/imx6q-udoo.dts @@ -21,19 +21,69 @@ }; }; +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + status = "okay"; +}; + +&iomuxc { + imx6q-udoo { + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + >; + }; + }; +}; + &sata { status = "okay"; }; &uart2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart2_1>; + pinctrl-0 = <&pinctrl_uart2>; status = "okay"; }; &usdhc3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc3_2>; + pinctrl-0 = <&pinctrl_usdhc3>; non-removable; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi index 2a8d9de666c9..addd3f881ce2 100644 --- a/arch/arm/boot/dts/imx6q.dtsi +++ b/arch/arm/boot/dts/imx6q.dtsi @@ -8,10 +8,15 @@ * */ +#include <dt-bindings/interrupt-controller/irq.h> #include "imx6q-pinfunc.h" #include "imx6qdl.dtsi" / { + aliases { + spi4 = &ecspi5; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -25,8 +30,17 @@ /* kHz uV */ 1200000 1275000 996000 1250000 + 852000 1250000 792000 1150000 - 396000 950000 + 396000 975000 + >; + fsl,soc-operating-points = < + /* ARM kHz SOC-PU uV */ + 1200000 1275000 + 996000 1250000 + 852000 1250000 + 792000 1175000 + 396000 1175000 >; clock-latency = <61036>; /* two CLK32 periods */ clocks = <&clks 104>, <&clks 6>, <&clks 16>, @@ -74,7 +88,7 @@ #size-cells = <0>; compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi"; reg = <0x02018000 0x4000>; - interrupts = <0 35 0x04>; + interrupts = <0 35 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 116>, <&clks 116>; clock-names = "ipg", "per"; status = "disabled"; @@ -125,7 +139,7 @@ sata: sata@02200000 { compatible = "fsl,imx6q-ahci"; reg = <0x02200000 0x4000>; - interrupts = <0 39 0x04>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 154>, <&clks 187>, <&clks 105>; clock-names = "sata", "sata_ref", "ahb"; status = "disabled"; @@ -136,7 +150,8 @@ #size-cells = <0>; compatible = "fsl,imx6q-ipu"; reg = <0x02800000 0x400000>; - interrupts = <0 8 0x4 0 7 0x4>; + interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>, + <0 7 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 133>, <&clks 134>, <&clks 137>; clock-names = "bus", "di0", "di1"; resets = <&src 4>; diff --git a/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi b/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi new file mode 100644 index 000000000000..25cf035dd36e --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-dfi-fs700-m60.dtsi @@ -0,0 +1,199 @@ +/ { + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + dummy_reg: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "dummy-supply"; + }; + + reg_usb_otg_vbus: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 0>; + enable-active-high; + }; + }; + + chosen { + linux,stdout-path = &uart1; + }; +}; + +&ecspi3 { + fsl,spi-num-chipselects = <1>; + cs-gpios = <&gpio4 24 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi3>; + status = "okay"; + + flash: m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "sst,sst25vf040b", "m25p80"; + spi-max-frequency = <20000000>; + reg = <0>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + status = "okay"; + phy-mode = "rgmii"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6qdl-dfi-fs700-m60 { + pinctrl_hog: hoggrp { + fsl,pins = < + MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x80000000 + MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x80000000 /* PMIC irq */ + MX6QDL_PAD_EIM_D26__GPIO3_IO26 0x80000000 /* MAX11801 irq */ + MX6QDL_PAD_NANDF_D5__GPIO2_IO05 0x000030b0 /* Backlight enable */ + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 + MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x80000000 /* card detect */ + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + >; + }; + + pinctrl_usdhc4: usdhc4grp { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 + MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059 + MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059 + MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059 + MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059 + >; + }; + + pinctrl_ecspi3: ecspi3grp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1 + MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1 + MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1 + MX6QDL_PAD_DISP0_DAT3__GPIO4_IO24 0x80000000 /* SPI NOR chipselect */ + >; + }; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&usbh1 { + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + dr_mode = "host"; + status = "okay"; +}; + +&usdhc2 { /* module slot */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc2>; + cd-gpios = <&gpio2 2 0>; + status = "okay"; +}; + +&usdhc3 { /* baseboard slot */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; +}; + +&usdhc4 { /* eMMC */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc4>; + bus-width = <8>; + non-removable; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi new file mode 100644 index 000000000000..98a422153ce7 --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi @@ -0,0 +1,374 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/ { + /* these are used by bootloader for disabling nodes */ + aliases { + can0 = &can1; + ethernet0 = &fec; + led0 = &led0; + led1 = &led1; + nand = &gpmi; + usb0 = &usbh1; + usb1 = &usbotg; + }; + + chosen { + bootargs = "console=ttymxc1,115200"; + }; + + leds { + compatible = "gpio-leds"; + + led0: user1 { + label = "user1"; + gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */ + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + led1: user2 { + label = "user2"; + gpios = <&gpio4 7 0>; /* 103 -> MX6_PANLEDR */ + default-state = "off"; + }; + }; + + memory { + reg = <0x10000000 0x20000000>; + }; + + pps { + compatible = "pps-gpio"; + gpios = <&gpio1 26 0>; + status = "okay"; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_3p3v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_5p0v: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "5P0V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + reg_usb_otg_vbus: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 0>; + enable-active-high; + }; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 30 0>; + status = "okay"; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + eeprom1: eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + + eeprom2: eeprom@51 { + compatible = "atmel,24c02"; + reg = <0x51>; + pagesize = <16>; + }; + + eeprom3: eeprom@52 { + compatible = "atmel,24c02"; + reg = <0x52>; + pagesize = <16>; + }; + + eeprom4: eeprom@53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; + + gpio: pca9555@23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + }; + + hwmon: gsc@29 { + compatible = "gw,gsp"; + reg = <0x29>; + }; + + rtc: ds1672@68 { + compatible = "dallas,ds1672"; + reg = <0x68>; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pmic: ltc3676@3c { + compatible = "ltc,ltc3676"; + reg = <0x3c>; + + regulators { + sw1_reg: ltc3676__sw1 { + regulator-min-microvolt = <1175000>; + regulator-max-microvolt = <1175000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: ltc3676__sw2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3_reg: ltc3676__sw3 { + regulator-min-microvolt = <1175000>; + regulator-max-microvolt = <1175000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: ltc3676__sw4 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ltc3676__ldo2 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: ltc3676__ldo4 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + videoin: adv7180@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6qdl-gw51xx { + pinctrl_hog: hoggrp { + fsl,pins = < + MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x80000000 /* MEZZ_DIO0 */ + MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x80000000 /* MEZZ_DIO1 */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x80000000 /* OTG_PWR_EN */ + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x80000000 /* GPS_PPS */ + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x80000000 /* PHY Reset */ + MX6QDL_PAD_GPIO_0__GPIO1_IO00 0x80000000 /* PCIE_RST# */ + MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x80000000 /* user1 led */ + MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x80000000 /* user2 led */ + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + >; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + >; + }; + }; +}; + +&pcie { + reset-gpio = <&gpio1 0 0>; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart3>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + status = "okay"; +}; + +&usbh1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi new file mode 100644 index 000000000000..8e99c9a9bc76 --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi @@ -0,0 +1,490 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/ { + /* these are used by bootloader for disabling nodes */ + aliases { + ethernet0 = &fec; + led0 = &led0; + led1 = &led1; + led2 = &led2; + nand = &gpmi; + ssi0 = &ssi1; + usb0 = &usbh1; + usb1 = &usbotg; + usdhc2 = &usdhc3; + }; + + chosen { + bootargs = "console=ttymxc1,115200"; + }; + + leds { + compatible = "gpio-leds"; + + led0: user1 { + label = "user1"; + gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */ + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + led1: user2 { + label = "user2"; + gpios = <&gpio4 7 0>; /* 103 -> MX6_PANLEDR */ + default-state = "off"; + }; + + led2: user3 { + label = "user3"; + gpios = <&gpio4 15 1>; /* 111 - MX6_LOCLED# */ + default-state = "off"; + }; + }; + + memory { + reg = <0x10000000 0x20000000>; + }; + + pps { + compatible = "pps-gpio"; + gpios = <&gpio1 26 0>; + status = "okay"; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_1p0v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "1P0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + /* remove this fixed regulator once ltc3676__sw2 driver available */ + reg_1p8v: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "1P8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + reg_3p3v: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_5p0v: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "5P0V"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + reg_usb_otg_vbus: regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 0>; + enable-active-high; + }; + }; + + sound { + compatible = "fsl,imx6q-sabrelite-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "imx6q-sabrelite-sgtl5000"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-int-port = <1>; + mux-ext-port = <4>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 30 0>; + status = "okay"; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + eeprom1: eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + + eeprom2: eeprom@51 { + compatible = "atmel,24c02"; + reg = <0x51>; + pagesize = <16>; + }; + + eeprom3: eeprom@52 { + compatible = "atmel,24c02"; + reg = <0x52>; + pagesize = <16>; + }; + + eeprom4: eeprom@53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; + + gpio: pca9555@23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + }; + + hwmon: gsc@29 { + compatible = "gw,gsp"; + reg = <0x29>; + }; + + rtc: ds1672@68 { + compatible = "dallas,ds1672"; + reg = <0x68>; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pciswitch: pex8609@3f { + compatible = "plx,pex8609"; + reg = <0x3f>; + }; + + pmic: ltc3676@3c { + compatible = "ltc,ltc3676"; + reg = <0x3c>; + + regulators { + sw1_reg: ltc3676__sw1 { + regulator-min-microvolt = <1175000>; + regulator-max-microvolt = <1175000>; + regulator-boot-on; + regulator-always-on; + }; + + sw2_reg: ltc3676__sw2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3_reg: ltc3676__sw3 { + regulator-min-microvolt = <1175000>; + regulator-max-microvolt = <1175000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: ltc3676__sw4 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo2_reg: ltc3676__ldo2 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo3_reg: ltc3676__ldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + ldo4_reg: ltc3676__ldo4 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + accelerometer: fxos8700@1e { + compatible = "fsl,fxos8700"; + reg = <0x13>; + }; + + codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + clocks = <&clks 169>; + VDDA-supply = <®_1p8v>; + VDDIO-supply = <®_3p3v>; + }; + + touchscreen: egalax_ts@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio7>; + interrupts = <12 2>; /* gpio7_12 active low */ + wakeup-gpios = <&gpio7 12 0>; + }; + + videoin: adv7180@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6qdl-gw52xx { + pinctrl_hog: hoggrp { + fsl,pins = < + MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x80000000 /* MEZZ_DIO0 */ + MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x80000000 /* MEZZ_DIO1 */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x80000000 /* OTG_PWR_EN */ + MX6QDL_PAD_EIM_D31__GPIO3_IO31 0x80000000 /* VIDDEC_PDN# */ + MX6QDL_PAD_ENET_TXD0__GPIO1_IO30 0x80000000 /* PHY Reset */ + MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 /* PCIE_RST# */ + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x80000000 /* GPS_PWDN */ + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x80000000 /* GPS_PPS */ + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000130b0 /* AUD4_MCK */ + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000 /* USB_SEL_PCI */ + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000 /* TOUCH_IRQ# */ + MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x80000000 /* user1 led */ + MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x80000000 /* user2 led */ + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x80000000 /* user3 led */ + MX6QDL_PAD_SD2_CMD__GPIO1_IO11 0x80000000 /* LVDS_TCH# */ + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x80000000 /* SD3_CD# */ + MX6QDL_PAD_SD4_DAT3__GPIO2_IO11 0x80000000 /* UART2_EN# */ + >; + }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x130b0 + MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x130b0 + MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x110b0 + MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x130b0 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + >; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + >; + }; + }; +}; + +&ldb { + status = "okay"; + lvds-channel@0 { + crtcs = <&ipu1 0>, <&ipu1 1>; + }; +}; + +&pcie { + reset-gpio = <&gpio1 29 0>; + status = "okay"; +}; + +&ssi1 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + status = "okay"; +}; + +&usbh1 { + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + cd-gpios = <&gpio7 0 0>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi new file mode 100644 index 000000000000..c8e5ae06deaf --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi @@ -0,0 +1,553 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/ { + /* these are used by bootloader for disabling nodes */ + aliases { + can0 = &can1; + ethernet0 = &fec; + ethernet1 = ð1; + led0 = &led0; + led1 = &led1; + led2 = &led2; + nand = &gpmi; + sky2 = ð1; + ssi0 = &ssi1; + usb0 = &usbh1; + usb1 = &usbotg; + usdhc2 = &usdhc3; + }; + + chosen { + bootargs = "console=ttymxc1,115200"; + }; + + leds { + compatible = "gpio-leds"; + + led0: user1 { + label = "user1"; + gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */ + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + led1: user2 { + label = "user2"; + gpios = <&gpio4 7 0>; /* 103 -> MX6_PANLEDR */ + default-state = "off"; + }; + + led2: user3 { + label = "user3"; + gpios = <&gpio4 15 1>; /* 111 -> MX6_LOCLED# */ + default-state = "off"; + }; + }; + + memory { + reg = <0x10000000 0x40000000>; + }; + + pps { + compatible = "pps-gpio"; + gpios = <&gpio1 26 0>; + status = "okay"; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_1p0v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "1P0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + /* remove when pmic 1p8 regulator available */ + reg_1p8v: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "1P8V"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + reg_3p3v: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_h1_vbus: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "usb_h1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + reg_usb_otg_vbus: regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 0>; + enable-active-high; + }; + }; + + sound { + compatible = "fsl,imx6q-sabrelite-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "imx6q-sabrelite-sgtl5000"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-int-port = <1>; + mux-ext-port = <4>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 30 0>; + status = "okay"; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + eeprom1: eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + + eeprom2: eeprom@51 { + compatible = "atmel,24c02"; + reg = <0x51>; + pagesize = <16>; + }; + + eeprom3: eeprom@52 { + compatible = "atmel,24c02"; + reg = <0x52>; + pagesize = <16>; + }; + + eeprom4: eeprom@53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; + + gpio: pca9555@23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + }; + + hwmon: gsc@29 { + compatible = "gw,gsp"; + reg = <0x29>; + }; + + rtc: ds1672@68 { + compatible = "dallas,ds1672"; + reg = <0x68>; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pciclkgen: si53156@6b { + compatible = "sil,si53156"; + reg = <0x6b>; + }; + + pciswitch: pex8606@3f { + compatible = "plx,pex8606"; + reg = <0x3f>; + }; + + pmic: ltc3676@3c { + compatible = "ltc,ltc3676"; + reg = <0x3c>; + + regulators { + /* VDD_SOC */ + sw1_reg: ltc3676__sw1 { + regulator-min-microvolt = <1175000>; + regulator-max-microvolt = <1175000>; + regulator-boot-on; + regulator-always-on; + }; + + /* VDD_1P8 */ + sw2_reg: ltc3676__sw2 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + /* VDD_ARM */ + sw3_reg: ltc3676__sw3 { + regulator-min-microvolt = <1175000>; + regulator-max-microvolt = <1175000>; + regulator-boot-on; + regulator-always-on; + }; + + /* VDD_DDR */ + sw4_reg: ltc3676__sw4 { + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-boot-on; + regulator-always-on; + }; + + /* VDD_2P5 */ + ldo2_reg: ltc3676__ldo2 { + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-boot-on; + regulator-always-on; + }; + + /* VDD_1P8 */ + ldo3_reg: ltc3676__ldo3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + }; + + /* VDD_HIGH */ + ldo4_reg: ltc3676__ldo4 { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + accelerometer: fxos8700@1e { + compatible = "fsl,fxos8700"; + reg = <0x1e>; + }; + + codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + clocks = <&clks 201>; + VDDA-supply = <®_1p8v>; + VDDIO-supply = <®_3p3v>; + }; + + hdmiin: adv7611@4c { + compatible = "adi,adv7611"; + reg = <0x4c>; + }; + + touchscreen: egalax_ts@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio1>; + interrupts = <11 2>; /* gpio1_11 active low */ + wakeup-gpios = <&gpio1 11 0>; + }; + + videoout: adv7393@2a { + compatible = "adi,adv7393"; + reg = <0x2a>; + }; + + videoin: adv7180@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6qdl-gw53xx { + pinctrl_hog: hoggrp { + fsl,pins = < + MX6QDL_PAD_EIM_A19__GPIO2_IO19 0x80000000 /* PCIE6EXP_DIO0 */ + MX6QDL_PAD_EIM_A20__GPIO2_IO18 0x80000000 /* PCIE6EXP_DIO1 */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x80000000 /* OTG_PWR_EN */ + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x80000000 /* GPS_SHDN */ + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x80000000 /* GPS_PPS */ + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x80000000 /* PCIE IRQ */ + MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 /* PCIE RST */ + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000130b0 /* AUD4_MCK */ + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000 /* CAN_STBY */ + MX6QDL_PAD_GPIO_8__GPIO1_IO08 0x80000000 /* PMIC_IRQ# */ + MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x80000000 /* HUB_RST# */ + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000 /* PCIE_WDIS# */ + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x80000000 /* ACCEL_IRQ# */ + MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x80000000 /* user1 led */ + MX6QDL_PAD_KEY_COL4__GPIO4_IO14 0x80000000 /* USBOTG_OC# */ + MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x80000000 /* user2 led */ + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x80000000 /* user3 led */ + MX6QDL_PAD_SD2_CMD__GPIO1_IO11 0x80000000 /* TOUCH_IRQ# */ + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x80000000 /* SD3_DET# */ + >; + }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x130b0 + MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x130b0 + MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x110b0 + MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x130b0 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + >; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000 + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000 + >; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + >; + }; + }; +}; + +&ldb { + status = "okay"; + + lvds-channel@1 { + fsl,data-mapping = "spwg"; + fsl,data-width = <18>; + status = "okay"; + + display-timings { + native-mode = <&timing0>; + timing0: hsd100pxn1 { + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hback-porch = <220>; + hfront-porch = <40>; + vback-porch = <21>; + vfront-porch = <7>; + hsync-len = <60>; + vsync-len = <10>; + }; + }; + }; +}; + +&pcie { + reset-gpio = <&gpio1 29 0>; + status = "okay"; + + eth1: sky2@8 { /* MAC/PHY on bus 8 */ + compatible = "marvell,sky2"; + }; +}; + +&ssi1 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usb_h1_vbus>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + cd-gpios = <&gpio7 0 0>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi new file mode 100644 index 000000000000..2795dfc8c926 --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi @@ -0,0 +1,580 @@ +/* + * Copyright 2013 Gateworks Corporation + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/ { + /* these are used by bootloader for disabling nodes */ + aliases { + can0 = &can1; + ethernet0 = &fec; + ethernet1 = ð1; + led0 = &led0; + led1 = &led1; + led2 = &led2; + nand = &gpmi; + sky2 = ð1; + ssi0 = &ssi1; + usb0 = &usbh1; + usb1 = &usbotg; + usdhc2 = &usdhc3; + }; + + chosen { + bootargs = "console=ttymxc1,115200"; + }; + + leds { + compatible = "gpio-leds"; + + led0: user1 { + label = "user1"; + gpios = <&gpio4 6 0>; /* 102 -> MX6_PANLEDG */ + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + led1: user2 { + label = "user2"; + gpios = <&gpio4 7 0>; /* 103 -> MX6_PANLEDR */ + default-state = "off"; + }; + + led2: user3 { + label = "user3"; + gpios = <&gpio4 15 1>; /* 111 -> MX6_LOCLED# */ + default-state = "off"; + }; + }; + + memory { + reg = <0x10000000 0x40000000>; + }; + + pps { + compatible = "pps-gpio"; + gpios = <&gpio1 26 0>; + status = "okay"; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_1p0v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "1P0V"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + }; + + reg_3p3v: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_h1_vbus: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "usb_h1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; + + reg_usb_otg_vbus: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 0>; + enable-active-high; + }; + }; + + sound { + compatible = "fsl,imx6q-sabrelite-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "imx6q-sabrelite-sgtl5000"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-int-port = <1>; + mux-ext-port = <4>; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; /* AUD4<->sgtl5000 */ + status = "okay"; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 30 0>; + status = "okay"; +}; + +&gpmi { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpmi_nand>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + eeprom1: eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + pagesize = <16>; + }; + + eeprom2: eeprom@51 { + compatible = "atmel,24c02"; + reg = <0x51>; + pagesize = <16>; + }; + + eeprom3: eeprom@52 { + compatible = "atmel,24c02"; + reg = <0x52>; + pagesize = <16>; + }; + + eeprom4: eeprom@53 { + compatible = "atmel,24c02"; + reg = <0x53>; + pagesize = <16>; + }; + + gpio: pca9555@23 { + compatible = "nxp,pca9555"; + reg = <0x23>; + gpio-controller; + #gpio-cells = <2>; + }; + + hwmon: gsc@29 { + compatible = "gw,gsp"; + reg = <0x29>; + }; + + rtc: ds1672@68 { + compatible = "dallas,ds1672"; + reg = <0x68>; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pmic: pfuze100@08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3950000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; + + pciswitch: pex8609@3f { + compatible = "plx,pex8609"; + reg = <0x3f>; + }; + + pciclkgen: si52147@6b { + compatible = "sil,si52147"; + reg = <0x6b>; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + accelerometer: fxos8700@1e { + compatible = "fsl,fxos8700"; + reg = <0x1e>; + }; + + codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + clocks = <&clks 201>; + VDDA-supply = <&sw4_reg>; + VDDIO-supply = <®_3p3v>; + }; + + hdmiin: adv7611@4c { + compatible = "adi,adv7611"; + reg = <0x4c>; + }; + + touchscreen: egalax_ts@04 { + compatible = "eeti,egalax_ts"; + reg = <0x04>; + interrupt-parent = <&gpio7>; + interrupts = <12 2>; /* gpio7_12 active low */ + wakeup-gpios = <&gpio7 12 0>; + }; + + videoout: adv7393@2a { + compatible = "adi,adv7393"; + reg = <0x2a>; + }; + + videoin: adv7180@20 { + compatible = "adi,adv7180"; + reg = <0x20>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6qdl-gw54xx { + pinctrl_hog: hoggrp { + fsl,pins = < + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x80000000 /* OTG_PWR_EN */ + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x80000000 /* SPINOR_CS0# */ + MX6QDL_PAD_ENET_RXD1__GPIO1_IO26 0x80000000 /* GPS_PPS */ + MX6QDL_PAD_ENET_TX_EN__GPIO1_IO28 0x80000000 /* PCIE IRQ */ + MX6QDL_PAD_ENET_TXD1__GPIO1_IO29 0x80000000 /* PCIE RST */ + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x000130b0 /* AUD4_MCK */ + MX6QDL_PAD_GPIO_2__GPIO1_IO02 0x80000000 /* CAN_STBY */ + MX6QDL_PAD_GPIO_17__GPIO7_IO12 0x80000000 /* TOUCH_IRQ# */ + MX6QDL_PAD_KEY_COL0__GPIO4_IO06 0x80000000 /* user1 led */ + MX6QDL_PAD_KEY_ROW0__GPIO4_IO07 0x80000000 /* user2 led */ + MX6QDL_PAD_KEY_ROW4__GPIO4_IO15 0x80000000 /* user3 led */ + MX6QDL_PAD_SD1_DAT0__GPIO1_IO16 0x80000000 /* USBHUB_RST# */ + MX6QDL_PAD_SD1_DAT3__GPIO1_IO21 0x80000000 /* MIPI_DIO */ + >; + }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x130b0 + MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x130b0 + MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x110b0 + MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x130b0 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + >; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000 + MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000 + >; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT7__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD4_DAT4__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart5: uart5grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__UART5_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW1__UART5_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + >; + }; + }; +}; + +&ldb { + status = "okay"; + + lvds-channel@1 { + fsl,data-mapping = "spwg"; + fsl,data-width = <18>; + status = "okay"; + + display-timings { + native-mode = <&timing0>; + timing0: hsd100pxn1 { + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hback-porch = <220>; + hfront-porch = <40>; + vback-porch = <21>; + vfront-porch = <7>; + hsync-len = <60>; + vsync-len = <10>; + }; + }; + }; +}; + +&pcie { + reset-gpio = <&gpio1 29 0>; + status = "okay"; + + eth1: sky2@8 { /* MAC/PHY on bus 8 */ + compatible = "marvell,sky2"; + }; +}; + +&ssi1 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&ssi2 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&uart5 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart5>; + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + status = "okay"; +}; + +&usbh1 { + vbus-supply = <®_usb_h1_vbus>; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + cd-gpios = <&gpio7 0 0>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi b/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi new file mode 100644 index 000000000000..99be301b5232 --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-nitrogen6x.dtsi @@ -0,0 +1,422 @@ +/* + * Copyright 2013 Boundary Devices, Inc. + * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + memory { + reg = <0x10000000 0x40000000>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_2p5v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + reg_3p3v: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_otg_vbus: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 0>; + enable-active-high; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys>; + + power { + label = "Power Button"; + gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + gpio-key,wakeup; + }; + + menu { + label = "Menu"; + gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; + linux,code = <KEY_MENU>; + }; + + home { + label = "Home"; + gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; + linux,code = <KEY_HOME>; + }; + + back { + label = "Back"; + gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; + linux,code = <KEY_BACK>; + }; + + volume-up { + label = "Volume Up"; + gpios = <&gpio7 13 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + + volume-down { + label = "Volume Down"; + gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEDOWN>; + }; + }; + + sound { + compatible = "fsl,imx6q-nitrogen6x-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "imx6q-nitrogen6x-sgtl5000"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-int-port = <1>; + mux-ext-port = <3>; + }; + + backlight_lcd { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + power-supply = <®_3p3v>; + status = "okay"; + }; + + backlight_lvds { + compatible = "pwm-backlight"; + pwms = <&pwm4 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + power-supply = <®_3p3v>; + status = "okay"; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&ecspi1 { + fsl,spi-num-chipselects = <1>; + cs-gpios = <&gpio3 19 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash: m25p80@0 { + compatible = "sst,sst25vf016b"; + spi-max-frequency = <20000000>; + reg = <0>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio1 27 0>; + txen-skew-ps = <0>; + txc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <3000>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txd0-skew-ps = <0>; + txd1-skew-ps = <0>; + txd2-skew-ps = <0>; + txd3-skew-ps = <0>; + interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>, + <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + clocks = <&clks 201>; + VDDA-supply = <®_2p5v>; + VDDIO-supply = <®_3p3v>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6q-nitrogen6x { + pinctrl_hog: hoggrp { + fsl,pins = < + /* SGTL5000 sys_mclk */ + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x030b0 + >; + }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1 /* CS */ + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + /* Phy reset */ + MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x000b0 + MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1 + >; + }; + + pinctrl_gpio_keys: gpio_keysgrp { + fsl,pins = < + /* Power Button */ + MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0 + /* Menu Button */ + MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0 + /* Home Button */ + MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0 + /* Back Button */ + MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0 + /* Volume Up Button */ + MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b0 + /* Volume Down Button */ + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm4: pwm4grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0 + /* power enable, high active */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x000b0 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0 /* CD */ + >; + }; + + pinctrl_usdhc4: usdhc4grp { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 + MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x1b0b0 /* CD */ + >; + }; + }; +}; + +&ldb { + status = "okay"; + + lvds-channel@0 { + fsl,data-mapping = "spwg"; + fsl,data-width = <18>; + status = "okay"; + + display-timings { + native-mode = <&timing0>; + timing0: hsd100pxn1 { + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hback-porch = <220>; + hfront-porch = <40>; + vback-porch = <21>; + vfront-porch = <7>; + hsync-len = <60>; + vsync-len = <10>; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "okay"; +}; + +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm4>; + status = "okay"; +}; + +&ssi1 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usbh1 { + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + cd-gpios = <&gpio7 0 0>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; + +&usdhc4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc4>; + cd-gpios = <&gpio2 6 0>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi index ff6f1e8f2dd9..009abd69385d 100644 --- a/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabreauto.dtsi @@ -10,17 +10,46 @@ * http://www.gnu.org/copyleft/gpl.html */ +#include <dt-bindings/gpio/gpio.h> + / { memory { reg = <0x10000000 0x80000000>; }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_leds>; + + user { + label = "debug"; + gpios = <&gpio5 15 GPIO_ACTIVE_HIGH>; + }; + }; + + sound-spdif { + compatible = "fsl,imx-audio-spdif", + "fsl,imx-sabreauto-spdif"; + model = "imx-spdif"; + spdif-controller = <&spdif>; + spdif-in; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm3 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + status = "okay"; + }; }; &ecspi1 { fsl,spi-num-chipselects = <1>; cs-gpios = <&gpio3 19 0>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi1_1 &pinctrl_ecspi1_sabreauto>; + pinctrl-0 = <&pinctrl_ecspi1 &pinctrl_ecspi1_cs>; status = "disabled"; /* pin conflict with WEIM NOR */ flash: m25p80@0 { @@ -34,22 +63,130 @@ &fec { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_enet_2>; + pinctrl-0 = <&pinctrl_enet>; phy-mode = "rgmii"; + interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>, + <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>; status = "okay"; }; &gpmi { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_gpmi_nand_1>; + pinctrl-0 = <&pinctrl_gpmi_nand>; + status = "okay"; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; status = "okay"; + + pmic: pfuze100@08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; }; &iomuxc { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; - hog { + imx6qdl-sabreauto { pinctrl_hog: hoggrp { fsl,pins = < MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x80000000 @@ -57,28 +194,245 @@ MX6QDL_PAD_GPIO_18__SD3_VSELECT 0x17059 >; }; - }; - ecspi1 { - pinctrl_ecspi1_sabreauto: ecspi1-sabreauto { + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 + >; + }; + + pinctrl_ecspi1_cs: ecspi1cs { fsl,pins = < MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x80000000 >; }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_KEY_COL2__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1 + >; + }; + + pinctrl_gpio_leds: gpioledsgrp { + fsl,pins = < + MX6QDL_PAD_DISP0_DAT21__GPIO5_IO15 0x80000000 + >; + }; + + pinctrl_gpmi_nand: gpminandgrp { + fsl,pins = < + MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 + MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 + MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 + MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 + MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 + MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 + MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 + MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 + MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 + MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 + MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 + MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 + MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 + MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 + MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 + MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 + MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_pwm3: pwm1grp { + fsl,pins = < + MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1 + >; + }; + + pinctrl_spdif: spdifgrp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__SPDIF_IN 0x1b0b0 + >; + }; + + pinctrl_uart4: uart4grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 + MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3grp100mhz { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170b9 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100b9 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170b9 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170b9 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170b9 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170b9 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170b9 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170b9 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170b9 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170b9 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3grp200mhz { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170f9 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170f9 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170f9 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170f9 + >; + }; + + pinctrl_weim_cs0: weimcs0grp { + fsl,pins = < + MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1 + >; + }; + + pinctrl_weim_nor: weimnorgrp { + fsl,pins = < + MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1 + MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1 + MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060 + MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0 + MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0 + MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0 + MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0 + MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0 + MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0 + MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0 + MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0 + MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0 + MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0 + MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0 + MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0 + MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0 + MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0 + MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0 + MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0 + MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1 + MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1 + MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1 + MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1 + MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1 + MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1 + MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1 + MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1 + MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1 + MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1 + MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1 + MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1 + MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1 + MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1 + MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1 + MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1 + MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1 + MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1 + MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1 + MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1 + MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1 + MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1 + MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1 + MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1 + >; + }; + }; +}; + +&ldb { + status = "okay"; + + lvds-channel@0 { + fsl,data-mapping = "spwg"; + fsl,data-width = <18>; + status = "okay"; + + display-timings { + native-mode = <&timing0>; + timing0: hsd100pxn1 { + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hback-porch = <220>; + hfront-porch = <40>; + vback-porch = <21>; + vfront-porch = <7>; + hsync-len = <60>; + vsync-len = <10>; + }; + }; }; }; +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "okay"; +}; + +&spdif { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spdif>; + status = "okay"; +}; + &uart4 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart4_1>; + pinctrl-0 = <&pinctrl_uart4>; status = "okay"; }; &usdhc3 { pinctrl-names = "default", "state_100mhz", "state_200mhz"; - pinctrl-0 = <&pinctrl_usdhc3_1>; - pinctrl-1 = <&pinctrl_usdhc3_1_100mhz>; - pinctrl-2 = <&pinctrl_usdhc3_1_200mhz>; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; cd-gpios = <&gpio6 15 0>; wp-gpios = <&gpio1 13 0>; status = "okay"; @@ -86,7 +440,7 @@ &weim { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_weim_nor_1 &pinctrl_weim_cs0_1>; + pinctrl-0 = <&pinctrl_weim_nor &pinctrl_weim_cs0>; #address-cells = <2>; #size-cells = <1>; ranges = <0 0 0x08000000 0x08000000>; diff --git a/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi new file mode 100644 index 000000000000..3bec128c7971 --- /dev/null +++ b/arch/arm/boot/dts/imx6qdl-sabrelite.dtsi @@ -0,0 +1,423 @@ +/* + * Copyright 2011 Freescale Semiconductor, Inc. + * Copyright 2011 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +/ { + memory { + reg = <0x10000000 0x40000000>; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_2p5v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "2P5V"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-always-on; + }; + + reg_3p3v: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_usb_otg_vbus: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "usb_otg_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio3 22 0>; + enable-active-high; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys>; + + power { + label = "Power Button"; + gpios = <&gpio2 3 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + gpio-key,wakeup; + }; + + menu { + label = "Menu"; + gpios = <&gpio2 1 GPIO_ACTIVE_LOW>; + linux,code = <KEY_MENU>; + }; + + home { + label = "Home"; + gpios = <&gpio2 4 GPIO_ACTIVE_LOW>; + linux,code = <KEY_HOME>; + }; + + back { + label = "Back"; + gpios = <&gpio2 2 GPIO_ACTIVE_LOW>; + linux,code = <KEY_BACK>; + }; + + volume-up { + label = "Volume Up"; + gpios = <&gpio7 13 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEUP>; + }; + + volume-down { + label = "Volume Down"; + gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; + linux,code = <KEY_VOLUMEDOWN>; + }; + }; + + sound { + compatible = "fsl,imx6q-sabrelite-sgtl5000", + "fsl,imx-audio-sgtl5000"; + model = "imx6q-sabrelite-sgtl5000"; + ssi-controller = <&ssi1>; + audio-codec = <&codec>; + audio-routing = + "MIC_IN", "Mic Jack", + "Mic Jack", "Mic Bias", + "Headphone Jack", "HP_OUT"; + mux-int-port = <1>; + mux-ext-port = <4>; + }; + + backlight_lcd { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + power-supply = <®_3p3v>; + status = "okay"; + }; + + backlight_lvds { + compatible = "pwm-backlight"; + pwms = <&pwm4 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <7>; + power-supply = <®_3p3v>; + status = "okay"; + }; +}; + +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux>; + status = "okay"; +}; + +&ecspi1 { + fsl,spi-num-chipselects = <1>; + cs-gpios = <&gpio3 19 0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + status = "okay"; + + flash: m25p80@0 { + compatible = "sst,sst25vf016b"; + spi-max-frequency = <20000000>; + reg = <0>; + }; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_enet>; + phy-mode = "rgmii"; + phy-reset-gpios = <&gpio3 23 GPIO_ACTIVE_LOW>; + txen-skew-ps = <0>; + txc-skew-ps = <3000>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <3000>; + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txd0-skew-ps = <0>; + txd1-skew-ps = <0>; + txd2-skew-ps = <0>; + txd3-skew-ps = <0>; + interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>, + <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + codec: sgtl5000@0a { + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + clocks = <&clks 201>; + VDDA-supply = <®_2p5v>; + VDDIO-supply = <®_3p3v>; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx6q-sabrelite { + pinctrl_hog: hoggrp { + fsl,pins = < + /* SGTL5000 sys_mclk */ + MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x030b0 + >; + }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x130b0 + MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x130b0 + MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x110b0 + MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x130b0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 + MX6QDL_PAD_EIM_D19__GPIO3_IO19 0x000b1 /* CS */ + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x100b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x100b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x100b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x100b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x100b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x100b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x100b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x100b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x100b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + /* Phy reset */ + MX6QDL_PAD_EIM_D23__GPIO3_IO23 0x000b0 + MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1 + >; + }; + + pinctrl_gpio_keys: gpio_keysgrp { + fsl,pins = < + /* Power Button */ + MX6QDL_PAD_NANDF_D3__GPIO2_IO03 0x1b0b0 + /* Menu Button */ + MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x1b0b0 + /* Home Button */ + MX6QDL_PAD_NANDF_D4__GPIO2_IO04 0x1b0b0 + /* Back Button */ + MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x1b0b0 + /* Volume Up Button */ + MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b0 + /* Volume Down Button */ + MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 + MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm3: pwm3grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT1__PWM3_OUT 0x1b0b1 + >; + }; + + pinctrl_pwm4: pwm4grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__PWM4_OUT 0x1b0b1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_SD3_DAT7__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_SD3_DAT6__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + MX6QDL_PAD_KEY_COL4__USB_OTG_OC 0x1b0b0 + /* power enable, high active */ + MX6QDL_PAD_EIM_D22__GPIO3_IO22 0x000b0 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0 /* CD */ + MX6QDL_PAD_SD3_DAT4__GPIO7_IO01 0x1f0b0 /* WP */ + >; + }; + + pinctrl_usdhc4: usdhc4grp { + fsl,pins = < + MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 + MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 + MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 + MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 + MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 + MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 + MX6QDL_PAD_NANDF_D6__GPIO2_IO06 0x1b0b0 /* CD */ + >; + }; + }; +}; + +&ldb { + status = "okay"; + + lvds-channel@0 { + fsl,data-mapping = "spwg"; + fsl,data-width = <18>; + status = "okay"; + + display-timings { + native-mode = <&timing0>; + timing0: hsd100pxn1 { + clock-frequency = <65000000>; + hactive = <1024>; + vactive = <768>; + hback-porch = <220>; + hfront-porch = <40>; + vback-porch = <21>; + vfront-porch = <7>; + hsync-len = <60>; + vsync-len = <10>; + }; + }; + }; +}; + +&pcie { + status = "okay"; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; + status = "okay"; +}; + +&pwm3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm3>; + status = "okay"; +}; + +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm4>; + status = "okay"; +}; + +&ssi1 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usbh1 { + status = "okay"; +}; + +&usbotg { + vbus-supply = <®_usb_otg_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg>; + disable-over-current; + status = "okay"; +}; + +&usdhc3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc3>; + cd-gpios = <&gpio7 0 0>; + wp-gpios = <&gpio7 1 0>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; + +&usdhc4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usdhc4>; + cd-gpios = <&gpio2 6 0>; + vmmc-supply = <®_3p3v>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi index e75e11b36dff..0d816d3be4b6 100644 --- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi +++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi @@ -10,6 +10,9 @@ * http://www.gnu.org/copyleft/gpl.html */ +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + / { memory { reg = <0x10000000 0x40000000>; @@ -17,9 +20,12 @@ regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_usb_otg_vbus: usb_otg_vbus { + reg_usb_otg_vbus: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "usb_otg_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; @@ -27,8 +33,9 @@ enable-active-high; }; - reg_usb_h1_vbus: usb_h1_vbus { + reg_usb_h1_vbus: regulator@1 { compatible = "regulator-fixed"; + reg = <1>; regulator-name = "usb_h1_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; @@ -36,8 +43,9 @@ enable-active-high; }; - reg_audio: wm8962_supply { + reg_audio: regulator@2 { compatible = "regulator-fixed"; + reg = <2>; regulator-name = "wm8962-supply"; gpio = <&gpio4 10 0>; enable-active-high; @@ -46,19 +54,28 @@ gpio-keys { compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_keys>; + + power { + label = "Power Button"; + gpios = <&gpio3 29 GPIO_ACTIVE_LOW>; + gpio-key,wakeup; + linux,code = <KEY_POWER>; + }; volume-up { label = "Volume Up"; - gpios = <&gpio1 4 0>; + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; gpio-key,wakeup; - linux,code = <115>; /* KEY_VOLUMEUP */ + linux,code = <KEY_VOLUMEUP>; }; volume-down { label = "Volume Down"; - gpios = <&gpio1 5 0>; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; gpio-key,wakeup; - linux,code = <114>; /* KEY_VOLUMEDOWN */ + linux,code = <KEY_VOLUMEDOWN>; }; }; @@ -92,7 +109,7 @@ &audmux { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_audmux_2>; + pinctrl-0 = <&pinctrl_audmux>; status = "okay"; }; @@ -100,7 +117,7 @@ fsl,spi-num-chipselects = <1>; cs-gpios = <&gpio4 9 0>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi1_2>; + pinctrl-0 = <&pinctrl_ecspi1>; status = "okay"; flash: m25p80@0 { @@ -114,7 +131,7 @@ &fec { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_enet_1>; + pinctrl-0 = <&pinctrl_enet>; phy-mode = "rgmii"; phy-reset-gpios = <&gpio1 25 0>; status = "okay"; @@ -123,7 +140,7 @@ &i2c1 { clock-frequency = <100000>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c1_2>; + pinctrl-0 = <&pinctrl_i2c1>; status = "okay"; codec: wm8962@1a { @@ -149,10 +166,116 @@ }; }; +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + pmic: pfuze100@08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; +}; + &i2c3 { clock-frequency = <100000>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c3_2>; + pinctrl-0 = <&pinctrl_i2c3>; status = "okay"; egalax_ts@04 { @@ -168,11 +291,9 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; - hog { + imx6qdl-sabresd { pinctrl_hog: hoggrp { fsl,pins = < - MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x80000000 - MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x80000000 MX6QDL_PAD_NANDF_D0__GPIO2_IO00 0x80000000 MX6QDL_PAD_NANDF_D1__GPIO2_IO01 0x80000000 MX6QDL_PAD_NANDF_D2__GPIO2_IO02 0x80000000 @@ -184,6 +305,122 @@ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x80000000 >; }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1 + MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1 + MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + >; + }; + + pinctrl_gpio_keys: gpio_keysgrp { + fsl,pins = < + MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x80000000 + MX6QDL_PAD_GPIO_4__GPIO1_IO04 0x80000000 + MX6QDL_PAD_GPIO_5__GPIO1_IO05 0x80000000 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1 + MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 + MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 + MX6QDL_PAD_NANDF_D4__SD2_DATA4 0x17059 + MX6QDL_PAD_NANDF_D5__SD2_DATA5 0x17059 + MX6QDL_PAD_NANDF_D6__SD2_DATA6 0x17059 + MX6QDL_PAD_NANDF_D7__SD2_DATA7 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059 + MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059 + MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059 + MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059 + >; + }; }; }; @@ -214,7 +451,7 @@ &pwm1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_pwm0_1>; + pinctrl-0 = <&pinctrl_pwm1>; status = "okay"; }; @@ -225,7 +462,7 @@ &uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_1>; + pinctrl-0 = <&pinctrl_uart1>; status = "okay"; }; @@ -237,14 +474,14 @@ &usbotg { vbus-supply = <®_usb_otg_vbus>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usbotg_2>; + pinctrl-0 = <&pinctrl_usbotg>; disable-over-current; status = "okay"; }; &usdhc2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc2_1>; + pinctrl-0 = <&pinctrl_usdhc2>; bus-width = <8>; cd-gpios = <&gpio2 2 0>; wp-gpios = <&gpio2 3 0>; @@ -253,7 +490,7 @@ &usdhc3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc3_1>; + pinctrl-0 = <&pinctrl_usdhc3>; bus-width = <8>; cd-gpios = <&gpio2 0 0>; wp-gpios = <&gpio2 1 0>; diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi index 35f547929167..bdfdf89d405f 100644 --- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi +++ b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi @@ -12,17 +12,21 @@ / { regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_2p5v: 2p5v { + reg_2p5v: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "2P5V"; regulator-min-microvolt = <2500000>; regulator-max-microvolt = <2500000>; regulator-always-on; }; - reg_3p3v: 3p3v { + reg_3p3v: regulator@1 { compatible = "regulator-fixed"; + reg = <1>; regulator-name = "3P3V"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; @@ -54,14 +58,14 @@ &audmux { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_audmux_2>; + pinctrl-0 = <&pinctrl_audmux>; status = "okay"; }; &i2c2 { clock-frequency = <100000>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c2_2>; + pinctrl-0 = <&pinctrl_i2c2>; status = "okay"; codec: sgtl5000@0a { @@ -77,7 +81,7 @@ pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; - hog { + imx6qdl-wandboard { pinctrl_hog: hoggrp { fsl,pins = < MX6QDL_PAD_GPIO_0__CCM_CLKO1 0x130b0 @@ -91,20 +95,121 @@ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x80000000 >; }; + + pinctrl_audmux: audmuxgrp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x130b0 + MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x130b0 + MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x110b0 + MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x130b0 + >; + }; + + pinctrl_enet: enetgrp { + fsl,pins = < + MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 + MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 + MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 + MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 + MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 + MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 + MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 + MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 + MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 + MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 + MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 + MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 + MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 + MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 + MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 + MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 + MX6QDL_PAD_GPIO_6__ENET_IRQ 0x000b1 + >; + }; + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 + MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_spdif: spdifgrp { + fsl,pins = < + MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1b0b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1 + MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1 + >; + }; + + pinctrl_uart3: uart3grp { + fsl,pins = < + MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 + MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1 + MX6QDL_PAD_EIM_EB3__UART3_RTS_B 0x1b0b1 + >; + }; + + pinctrl_usbotg: usbotggrp { + fsl,pins = < + MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059 + MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059 + MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059 + MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059 + MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059 + MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + >; + }; }; }; &fec { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_enet_1>; + pinctrl-0 = <&pinctrl_enet>; phy-mode = "rgmii"; phy-reset-gpios = <&gpio3 29 0>; + interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>, + <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>; status = "okay"; }; &spdif { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_spdif_3>; + pinctrl-0 = <&pinctrl_spdif>; status = "okay"; }; @@ -115,13 +220,13 @@ &uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_1>; + pinctrl-0 = <&pinctrl_uart1>; status = "okay"; }; &uart3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart3_2>; + pinctrl-0 = <&pinctrl_uart3>; fsl,uart-has-rtscts; status = "okay"; }; @@ -132,7 +237,7 @@ &usbotg { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usbotg_1>; + pinctrl-0 = <&pinctrl_usbotg>; disable-over-current; dr_mode = "peripheral"; status = "okay"; @@ -140,21 +245,21 @@ &usdhc1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc1_2>; + pinctrl-0 = <&pinctrl_usdhc1>; cd-gpios = <&gpio1 2 0>; status = "okay"; }; &usdhc2 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc2_2>; + pinctrl-0 = <&pinctrl_usdhc2>; non-removable; status = "okay"; }; &usdhc3 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usdhc3_2>; + pinctrl-0 = <&pinctrl_usdhc3>; cd-gpios = <&gpio3 9 0>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi index 64a8cbe9480f..55cb926fa3f7 100644 --- a/arch/arm/boot/dts/imx6qdl.dtsi +++ b/arch/arm/boot/dts/imx6qdl.dtsi @@ -14,6 +14,8 @@ / { aliases { + can0 = &can1; + can1 = &can2; gpio0 = &gpio1; gpio1 = &gpio2; gpio2 = &gpio3; @@ -24,6 +26,10 @@ i2c0 = &i2c1; i2c1 = &i2c2; i2c2 = &i2c3; + mmc0 = &usdhc1; + mmc1 = &usdhc2; + mmc2 = &usdhc3; + mmc3 = &usdhc4; serial0 = &uart1; serial1 = &uart2; serial2 = &uart3; @@ -33,6 +39,8 @@ spi1 = &ecspi2; spi2 = &ecspi3; spi3 = &ecspi4; + usbphy0 = &usbphy1; + usbphy1 = &usbphy2; }; intc: interrupt-controller@00a01000 { @@ -75,7 +83,10 @@ dma_apbh: dma-apbh@00110000 { compatible = "fsl,imx6q-dma-apbh", "fsl,imx28-dma-apbh"; reg = <0x00110000 0x2000>; - interrupts = <0 13 0x04>, <0 13 0x04>, <0 13 0x04>, <0 13 0x04>; + interrupts = <0 13 IRQ_TYPE_LEVEL_HIGH>, + <0 13 IRQ_TYPE_LEVEL_HIGH>, + <0 13 IRQ_TYPE_LEVEL_HIGH>, + <0 13 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "gpmi0", "gpmi1", "gpmi2", "gpmi3"; #dma-cells = <1>; dma-channels = <4>; @@ -88,7 +99,7 @@ #size-cells = <1>; reg = <0x00112000 0x2000>, <0x00114000 0x2000>; reg-names = "gpmi-nand", "bch"; - interrupts = <0 15 0x04>; + interrupts = <0 15 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "bch"; clocks = <&clks 152>, <&clks 153>, <&clks 151>, <&clks 150>, <&clks 149>; @@ -109,7 +120,7 @@ L2: l2-cache@00a02000 { compatible = "arm,pl310-cache"; reg = <0x00a02000 0x1000>; - interrupts = <0 92 0x04>; + interrupts = <0 92 IRQ_TYPE_LEVEL_HIGH>; cache-unified; cache-level = <2>; arm,tag-latency = <4 2 3>; @@ -126,7 +137,7 @@ 0x81000000 0 0 0x01f80000 0 0x00010000 /* downstream I/O */ 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; /* non-prefetchable memory */ num-lanes = <1>; - interrupts = <0 123 0x04>; + interrupts = <0 123 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 189>, <&clks 187>, <&clks 206>, <&clks 144>; clock-names = "pcie_ref_125m", "sata_ref_100m", "lvds_gate", "pcie_axi"; status = "disabled"; @@ -134,7 +145,7 @@ pmu { compatible = "arm,cortex-a9-pmu"; - interrupts = <0 94 0x04>; + interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>; }; aips-bus@02000000 { /* AIPS1 */ @@ -154,7 +165,7 @@ spdif: spdif@02004000 { compatible = "fsl,imx35-spdif"; reg = <0x02004000 0x4000>; - interrupts = <0 52 0x04>; + interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>; dmas = <&sdma 14 18 0>, <&sdma 15 18 0>; dma-names = "rx", "tx"; @@ -176,9 +187,11 @@ #size-cells = <0>; compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi"; reg = <0x02008000 0x4000>; - interrupts = <0 31 0x04>; + interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 112>, <&clks 112>; clock-names = "ipg", "per"; + dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -187,9 +200,11 @@ #size-cells = <0>; compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi"; reg = <0x0200c000 0x4000>; - interrupts = <0 32 0x04>; + interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 113>, <&clks 113>; clock-names = "ipg", "per"; + dmas = <&sdma 5 7 1>, <&sdma 6 7 2>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -198,9 +213,11 @@ #size-cells = <0>; compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi"; reg = <0x02010000 0x4000>; - interrupts = <0 33 0x04>; + interrupts = <0 33 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 114>, <&clks 114>; clock-names = "ipg", "per"; + dmas = <&sdma 7 7 1>, <&sdma 8 7 2>; + dma-names = "rx", "tx"; status = "disabled"; }; @@ -209,16 +226,18 @@ #size-cells = <0>; compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi"; reg = <0x02014000 0x4000>; - interrupts = <0 34 0x04>; + interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 115>, <&clks 115>; clock-names = "ipg", "per"; + dmas = <&sdma 9 7 1>, <&sdma 10 7 2>; + dma-names = "rx", "tx"; status = "disabled"; }; uart1: serial@02020000 { compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x02020000 0x4000>; - interrupts = <0 26 0x04>; + interrupts = <0 26 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 160>, <&clks 161>; clock-names = "ipg", "per"; dmas = <&sdma 25 4 0>, <&sdma 26 4 0>; @@ -228,13 +247,15 @@ esai: esai@02024000 { reg = <0x02024000 0x4000>; - interrupts = <0 51 0x04>; + interrupts = <0 51 IRQ_TYPE_LEVEL_HIGH>; }; ssi1: ssi@02028000 { - compatible = "fsl,imx6q-ssi","fsl,imx21-ssi"; + compatible = "fsl,imx6q-ssi", + "fsl,imx51-ssi", + "fsl,imx21-ssi"; reg = <0x02028000 0x4000>; - interrupts = <0 46 0x04>; + interrupts = <0 46 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 178>; dmas = <&sdma 37 1 0>, <&sdma 38 1 0>; @@ -245,9 +266,11 @@ }; ssi2: ssi@0202c000 { - compatible = "fsl,imx6q-ssi","fsl,imx21-ssi"; + compatible = "fsl,imx6q-ssi", + "fsl,imx51-ssi", + "fsl,imx21-ssi"; reg = <0x0202c000 0x4000>; - interrupts = <0 47 0x04>; + interrupts = <0 47 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 179>; dmas = <&sdma 41 1 0>, <&sdma 42 1 0>; @@ -258,9 +281,11 @@ }; ssi3: ssi@02030000 { - compatible = "fsl,imx6q-ssi","fsl,imx21-ssi"; + compatible = "fsl,imx6q-ssi", + "fsl,imx51-ssi", + "fsl,imx21-ssi"; reg = <0x02030000 0x4000>; - interrupts = <0 48 0x04>; + interrupts = <0 48 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 180>; dmas = <&sdma 45 1 0>, <&sdma 46 1 0>; @@ -272,7 +297,7 @@ asrc: asrc@02034000 { reg = <0x02034000 0x4000>; - interrupts = <0 50 0x04>; + interrupts = <0 50 IRQ_TYPE_LEVEL_HIGH>; }; spba@0203c000 { @@ -282,7 +307,8 @@ vpu: vpu@02040000 { reg = <0x02040000 0x3c000>; - interrupts = <0 3 0x04 0 12 0x04>; + interrupts = <0 3 IRQ_TYPE_LEVEL_HIGH>, + <0 12 IRQ_TYPE_LEVEL_HIGH>; }; aipstz@0207c000 { /* AIPSTZ1 */ @@ -293,7 +319,7 @@ #pwm-cells = <2>; compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm"; reg = <0x02080000 0x4000>; - interrupts = <0 83 0x04>; + interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 62>, <&clks 145>; clock-names = "ipg", "per"; }; @@ -302,7 +328,7 @@ #pwm-cells = <2>; compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm"; reg = <0x02084000 0x4000>; - interrupts = <0 84 0x04>; + interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 62>, <&clks 146>; clock-names = "ipg", "per"; }; @@ -311,7 +337,7 @@ #pwm-cells = <2>; compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm"; reg = <0x02088000 0x4000>; - interrupts = <0 85 0x04>; + interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 62>, <&clks 147>; clock-names = "ipg", "per"; }; @@ -320,7 +346,7 @@ #pwm-cells = <2>; compatible = "fsl,imx6q-pwm", "fsl,imx27-pwm"; reg = <0x0208c000 0x4000>; - interrupts = <0 86 0x04>; + interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 62>, <&clks 148>; clock-names = "ipg", "per"; }; @@ -328,23 +354,25 @@ can1: flexcan@02090000 { compatible = "fsl,imx6q-flexcan"; reg = <0x02090000 0x4000>; - interrupts = <0 110 0x04>; + interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 108>, <&clks 109>; clock-names = "ipg", "per"; + status = "disabled"; }; can2: flexcan@02094000 { compatible = "fsl,imx6q-flexcan"; reg = <0x02094000 0x4000>; - interrupts = <0 111 0x04>; + interrupts = <0 111 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 110>, <&clks 111>; clock-names = "ipg", "per"; + status = "disabled"; }; gpt: gpt@02098000 { compatible = "fsl,imx6q-gpt", "fsl,imx31-gpt"; reg = <0x02098000 0x4000>; - interrupts = <0 55 0x04>; + interrupts = <0 55 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 119>, <&clks 120>; clock-names = "ipg", "per"; }; @@ -352,7 +380,8 @@ gpio1: gpio@0209c000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x0209c000 0x4000>; - interrupts = <0 66 0x04 0 67 0x04>; + interrupts = <0 66 IRQ_TYPE_LEVEL_HIGH>, + <0 67 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -362,7 +391,8 @@ gpio2: gpio@020a0000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x020a0000 0x4000>; - interrupts = <0 68 0x04 0 69 0x04>; + interrupts = <0 68 IRQ_TYPE_LEVEL_HIGH>, + <0 69 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -372,7 +402,8 @@ gpio3: gpio@020a4000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x020a4000 0x4000>; - interrupts = <0 70 0x04 0 71 0x04>; + interrupts = <0 70 IRQ_TYPE_LEVEL_HIGH>, + <0 71 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -382,7 +413,8 @@ gpio4: gpio@020a8000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x020a8000 0x4000>; - interrupts = <0 72 0x04 0 73 0x04>; + interrupts = <0 72 IRQ_TYPE_LEVEL_HIGH>, + <0 73 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -392,7 +424,8 @@ gpio5: gpio@020ac000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x020ac000 0x4000>; - interrupts = <0 74 0x04 0 75 0x04>; + interrupts = <0 74 IRQ_TYPE_LEVEL_HIGH>, + <0 75 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -402,7 +435,8 @@ gpio6: gpio@020b0000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x020b0000 0x4000>; - interrupts = <0 76 0x04 0 77 0x04>; + interrupts = <0 76 IRQ_TYPE_LEVEL_HIGH>, + <0 77 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -412,7 +446,8 @@ gpio7: gpio@020b4000 { compatible = "fsl,imx6q-gpio", "fsl,imx35-gpio"; reg = <0x020b4000 0x4000>; - interrupts = <0 78 0x04 0 79 0x04>; + interrupts = <0 78 IRQ_TYPE_LEVEL_HIGH>, + <0 79 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -421,20 +456,20 @@ kpp: kpp@020b8000 { reg = <0x020b8000 0x4000>; - interrupts = <0 82 0x04>; + interrupts = <0 82 IRQ_TYPE_LEVEL_HIGH>; }; wdog1: wdog@020bc000 { compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt"; reg = <0x020bc000 0x4000>; - interrupts = <0 80 0x04>; + interrupts = <0 80 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 0>; }; wdog2: wdog@020c0000 { compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt"; reg = <0x020c0000 0x4000>; - interrupts = <0 81 0x04>; + interrupts = <0 81 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 0>; status = "disabled"; }; @@ -442,14 +477,17 @@ clks: ccm@020c4000 { compatible = "fsl,imx6q-ccm"; reg = <0x020c4000 0x4000>; - interrupts = <0 87 0x04 0 88 0x04>; + interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>, + <0 88 IRQ_TYPE_LEVEL_HIGH>; #clock-cells = <1>; }; anatop: anatop@020c8000 { compatible = "fsl,imx6q-anatop", "syscon", "simple-bus"; reg = <0x020c8000 0x1000>; - interrupts = <0 49 0x04 0 54 0x04 0 127 0x04>; + interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>, + <0 54 IRQ_TYPE_LEVEL_HIGH>, + <0 127 IRQ_TYPE_LEVEL_HIGH>; regulator-1p1@110 { compatible = "fsl,anatop-regulator"; @@ -495,7 +533,7 @@ reg_arm: regulator-vddcore@140 { compatible = "fsl,anatop-regulator"; - regulator-name = "cpu"; + regulator-name = "vddarm"; regulator-min-microvolt = <725000>; regulator-max-microvolt = <1450000>; regulator-always-on; @@ -547,23 +585,26 @@ tempmon: tempmon { compatible = "fsl,imx6q-tempmon"; - interrupts = <0 49 0x04>; + interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>; fsl,tempmon = <&anatop>; fsl,tempmon-data = <&ocotp>; + clocks = <&clks 172>; }; usbphy1: usbphy@020c9000 { compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; reg = <0x020c9000 0x1000>; - interrupts = <0 44 0x04>; + interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 182>; + fsl,anatop = <&anatop>; }; usbphy2: usbphy@020ca000 { compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; reg = <0x020ca000 0x1000>; - interrupts = <0 45 0x04>; + interrupts = <0 45 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 183>; + fsl,anatop = <&anatop>; }; snvs@020cc000 { @@ -575,31 +616,34 @@ snvs-rtc-lp@34 { compatible = "fsl,sec-v4.0-mon-rtc-lp"; reg = <0x34 0x58>; - interrupts = <0 19 0x04 0 20 0x04>; + interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>, + <0 20 IRQ_TYPE_LEVEL_HIGH>; }; }; epit1: epit@020d0000 { /* EPIT1 */ reg = <0x020d0000 0x4000>; - interrupts = <0 56 0x04>; + interrupts = <0 56 IRQ_TYPE_LEVEL_HIGH>; }; epit2: epit@020d4000 { /* EPIT2 */ reg = <0x020d4000 0x4000>; - interrupts = <0 57 0x04>; + interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>; }; src: src@020d8000 { compatible = "fsl,imx6q-src", "fsl,imx51-src"; reg = <0x020d8000 0x4000>; - interrupts = <0 91 0x04 0 96 0x04>; + interrupts = <0 91 IRQ_TYPE_LEVEL_HIGH>, + <0 96 IRQ_TYPE_LEVEL_HIGH>; #reset-cells = <1>; }; gpc: gpc@020dc000 { compatible = "fsl,imx6q-gpc"; reg = <0x020dc000 0x4000>; - interrupts = <0 89 0x04 0 90 0x04>; + interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>, + <0 90 IRQ_TYPE_LEVEL_HIGH>; }; gpr: iomuxc-gpr@020e0000 { @@ -610,744 +654,6 @@ iomuxc: iomuxc@020e0000 { compatible = "fsl,imx6dl-iomuxc", "fsl,imx6q-iomuxc"; reg = <0x020e0000 0x4000>; - - audmux { - pinctrl_audmux_1: audmux-1 { - fsl,pins = < - MX6QDL_PAD_SD2_DAT0__AUD4_RXD 0x80000000 - MX6QDL_PAD_SD2_DAT3__AUD4_TXC 0x80000000 - MX6QDL_PAD_SD2_DAT2__AUD4_TXD 0x80000000 - MX6QDL_PAD_SD2_DAT1__AUD4_TXFS 0x80000000 - >; - }; - - pinctrl_audmux_2: audmux-2 { - fsl,pins = < - MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x80000000 - MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x80000000 - MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x80000000 - MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x80000000 - >; - }; - - pinctrl_audmux_3: audmux-3 { - fsl,pins = < - MX6QDL_PAD_DISP0_DAT16__AUD5_TXC 0x80000000 - MX6QDL_PAD_DISP0_DAT18__AUD5_TXFS 0x80000000 - MX6QDL_PAD_DISP0_DAT19__AUD5_RXD 0x80000000 - >; - }; - }; - - ecspi1 { - pinctrl_ecspi1_1: ecspi1grp-1 { - fsl,pins = < - MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1 - MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1 - MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1 - >; - }; - - pinctrl_ecspi1_2: ecspi1grp-2 { - fsl,pins = < - MX6QDL_PAD_KEY_COL1__ECSPI1_MISO 0x100b1 - MX6QDL_PAD_KEY_ROW0__ECSPI1_MOSI 0x100b1 - MX6QDL_PAD_KEY_COL0__ECSPI1_SCLK 0x100b1 - >; - }; - }; - - ecspi3 { - pinctrl_ecspi3_1: ecspi3grp-1 { - fsl,pins = < - MX6QDL_PAD_DISP0_DAT2__ECSPI3_MISO 0x100b1 - MX6QDL_PAD_DISP0_DAT1__ECSPI3_MOSI 0x100b1 - MX6QDL_PAD_DISP0_DAT0__ECSPI3_SCLK 0x100b1 - >; - }; - }; - - enet { - pinctrl_enet_1: enetgrp-1 { - fsl,pins = < - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 - MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 - MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 - MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 - MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 - MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 - MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 - MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 - MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 - MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 - MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 - MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 - MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 - MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 - MX6QDL_PAD_GPIO_16__ENET_REF_CLK 0x4001b0a8 - >; - }; - - pinctrl_enet_2: enetgrp-2 { - fsl,pins = < - MX6QDL_PAD_KEY_COL1__ENET_MDIO 0x1b0b0 - MX6QDL_PAD_KEY_COL2__ENET_MDC 0x1b0b0 - MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 - MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 - MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 - MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 - MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 - MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 - MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 - MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 - MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 - MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 - MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 - MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 - MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 - >; - }; - - pinctrl_enet_3: enetgrp-3 { - fsl,pins = < - MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0 - MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0 - MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0 - MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0 - MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0 - MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0 - MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0 - MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0 - MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0 - MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0 - MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0 - MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0 - MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0 - MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0 - MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0 - MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN 0x1b0b0 - >; - }; - }; - - esai { - pinctrl_esai_1: esaigrp-1 { - fsl,pins = < - MX6QDL_PAD_ENET_RXD0__ESAI_TX_HF_CLK 0x1b030 - MX6QDL_PAD_ENET_CRS_DV__ESAI_TX_CLK 0x1b030 - MX6QDL_PAD_ENET_RXD1__ESAI_TX_FS 0x1b030 - MX6QDL_PAD_ENET_TX_EN__ESAI_TX3_RX2 0x1b030 - MX6QDL_PAD_ENET_TXD1__ESAI_TX2_RX3 0x1b030 - MX6QDL_PAD_ENET_TXD0__ESAI_TX4_RX1 0x1b030 - MX6QDL_PAD_ENET_MDC__ESAI_TX5_RX0 0x1b030 - MX6QDL_PAD_NANDF_CS2__ESAI_TX0 0x1b030 - MX6QDL_PAD_NANDF_CS3__ESAI_TX1 0x1b030 - >; - }; - - pinctrl_esai_2: esaigrp-2 { - fsl,pins = < - MX6QDL_PAD_ENET_CRS_DV__ESAI_TX_CLK 0x1b030 - MX6QDL_PAD_ENET_RXD1__ESAI_TX_FS 0x1b030 - MX6QDL_PAD_ENET_TX_EN__ESAI_TX3_RX2 0x1b030 - MX6QDL_PAD_GPIO_5__ESAI_TX2_RX3 0x1b030 - MX6QDL_PAD_ENET_TXD0__ESAI_TX4_RX1 0x1b030 - MX6QDL_PAD_ENET_MDC__ESAI_TX5_RX0 0x1b030 - MX6QDL_PAD_GPIO_17__ESAI_TX0 0x1b030 - MX6QDL_PAD_NANDF_CS3__ESAI_TX1 0x1b030 - MX6QDL_PAD_ENET_MDIO__ESAI_RX_CLK 0x1b030 - MX6QDL_PAD_GPIO_9__ESAI_RX_FS 0x1b030 - >; - }; - }; - - flexcan1 { - pinctrl_flexcan1_1: flexcan1grp-1 { - fsl,pins = < - MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000 - MX6QDL_PAD_KEY_COL2__FLEXCAN1_TX 0x80000000 - >; - }; - - pinctrl_flexcan1_2: flexcan1grp-2 { - fsl,pins = < - MX6QDL_PAD_GPIO_7__FLEXCAN1_TX 0x80000000 - MX6QDL_PAD_KEY_ROW2__FLEXCAN1_RX 0x80000000 - >; - }; - }; - - flexcan2 { - pinctrl_flexcan2_1: flexcan2grp-1 { - fsl,pins = < - MX6QDL_PAD_KEY_COL4__FLEXCAN2_TX 0x80000000 - MX6QDL_PAD_KEY_ROW4__FLEXCAN2_RX 0x80000000 - >; - }; - }; - - gpmi-nand { - pinctrl_gpmi_nand_1: gpmi-nand-1 { - fsl,pins = < - MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1 - MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1 - MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1 - MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000 - MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1 - MX6QDL_PAD_NANDF_CS1__NAND_CE1_B 0xb0b1 - MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1 - MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1 - MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1 - MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1 - MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1 - MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1 - MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1 - MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1 - MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1 - MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1 - MX6QDL_PAD_SD4_DAT0__NAND_DQS 0x00b1 - >; - }; - }; - - hdmi_hdcp { - pinctrl_hdmi_hdcp_1: hdmihdcpgrp-1 { - fsl,pins = < - MX6QDL_PAD_KEY_COL3__HDMI_TX_DDC_SCL 0x4001b8b1 - MX6QDL_PAD_KEY_ROW3__HDMI_TX_DDC_SDA 0x4001b8b1 - >; - }; - - pinctrl_hdmi_hdcp_2: hdmihdcpgrp-2 { - fsl,pins = < - MX6QDL_PAD_EIM_EB2__HDMI_TX_DDC_SCL 0x4001b8b1 - MX6QDL_PAD_EIM_D16__HDMI_TX_DDC_SDA 0x4001b8b1 - >; - }; - - pinctrl_hdmi_hdcp_3: hdmihdcpgrp-3 { - fsl,pins = < - MX6QDL_PAD_EIM_EB2__HDMI_TX_DDC_SCL 0x4001b8b1 - MX6QDL_PAD_KEY_ROW3__HDMI_TX_DDC_SDA 0x4001b8b1 - >; - }; - }; - - hdmi_cec { - pinctrl_hdmi_cec_1: hdmicecgrp-1 { - fsl,pins = < - MX6QDL_PAD_EIM_A25__HDMI_TX_CEC_LINE 0x1f8b0 - >; - }; - - pinctrl_hdmi_cec_2: hdmicecgrp-2 { - fsl,pins = < - MX6QDL_PAD_KEY_ROW2__HDMI_TX_CEC_LINE 0x1f8b0 - >; - }; - }; - - i2c1 { - pinctrl_i2c1_1: i2c1grp-1 { - fsl,pins = < - MX6QDL_PAD_EIM_D21__I2C1_SCL 0x4001b8b1 - MX6QDL_PAD_EIM_D28__I2C1_SDA 0x4001b8b1 - >; - }; - - pinctrl_i2c1_2: i2c1grp-2 { - fsl,pins = < - MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1 - MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1 - >; - }; - }; - - i2c2 { - pinctrl_i2c2_1: i2c2grp-1 { - fsl,pins = < - MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1 - MX6QDL_PAD_EIM_D16__I2C2_SDA 0x4001b8b1 - >; - }; - - pinctrl_i2c2_2: i2c2grp-2 { - fsl,pins = < - MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1 - MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 - >; - }; - - pinctrl_i2c2_3: i2c2grp-3 { - fsl,pins = < - MX6QDL_PAD_EIM_EB2__I2C2_SCL 0x4001b8b1 - MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1 - >; - }; - }; - - i2c3 { - pinctrl_i2c3_1: i2c3grp-1 { - fsl,pins = < - MX6QDL_PAD_EIM_D17__I2C3_SCL 0x4001b8b1 - MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 - >; - }; - - pinctrl_i2c3_2: i2c3grp-2 { - fsl,pins = < - MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 - MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1 - >; - }; - - pinctrl_i2c3_3: i2c3grp-3 { - fsl,pins = < - MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1 - MX6QDL_PAD_GPIO_16__I2C3_SDA 0x4001b8b1 - >; - }; - - pinctrl_i2c3_4: i2c3grp-4 { - fsl,pins = < - MX6QDL_PAD_GPIO_3__I2C3_SCL 0x4001b8b1 - MX6QDL_PAD_EIM_D18__I2C3_SDA 0x4001b8b1 - >; - }; - }; - - ipu1 { - pinctrl_ipu1_1: ipu1grp-1 { - fsl,pins = < - MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x10 - MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0x10 - MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10 - MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10 - MX6QDL_PAD_DI0_PIN4__IPU1_DI0_PIN04 0x80000000 - MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0x10 - MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0x10 - MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0x10 - MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0x10 - MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0x10 - MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0x10 - MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0x10 - MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0x10 - MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0x10 - MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0x10 - MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0x10 - MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0x10 - MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0x10 - MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0x10 - MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0x10 - MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0x10 - MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0x10 - MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0x10 - MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0x10 - MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0x10 - MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0x10 - MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0x10 - MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0x10 - MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0x10 - >; - }; - - pinctrl_ipu1_2: ipu1grp-2 { /* parallel camera */ - fsl,pins = < - MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x80000000 - MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x80000000 - MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x80000000 - MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x80000000 - MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x80000000 - MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x80000000 - MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x80000000 - MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x80000000 - MX6QDL_PAD_CSI0_DATA_EN__IPU1_CSI0_DATA_EN 0x80000000 - MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x80000000 - MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x80000000 - MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x80000000 - >; - }; - - pinctrl_ipu1_3: ipu1grp-3 { /* parallel port 16-bit */ - fsl,pins = < - MX6QDL_PAD_CSI0_DAT4__IPU1_CSI0_DATA04 0x80000000 - MX6QDL_PAD_CSI0_DAT5__IPU1_CSI0_DATA05 0x80000000 - MX6QDL_PAD_CSI0_DAT6__IPU1_CSI0_DATA06 0x80000000 - MX6QDL_PAD_CSI0_DAT7__IPU1_CSI0_DATA07 0x80000000 - MX6QDL_PAD_CSI0_DAT8__IPU1_CSI0_DATA08 0x80000000 - MX6QDL_PAD_CSI0_DAT9__IPU1_CSI0_DATA09 0x80000000 - MX6QDL_PAD_CSI0_DAT10__IPU1_CSI0_DATA10 0x80000000 - MX6QDL_PAD_CSI0_DAT11__IPU1_CSI0_DATA11 0x80000000 - MX6QDL_PAD_CSI0_DAT12__IPU1_CSI0_DATA12 0x80000000 - MX6QDL_PAD_CSI0_DAT13__IPU1_CSI0_DATA13 0x80000000 - MX6QDL_PAD_CSI0_DAT14__IPU1_CSI0_DATA14 0x80000000 - MX6QDL_PAD_CSI0_DAT15__IPU1_CSI0_DATA15 0x80000000 - MX6QDL_PAD_CSI0_DAT16__IPU1_CSI0_DATA16 0x80000000 - MX6QDL_PAD_CSI0_DAT17__IPU1_CSI0_DATA17 0x80000000 - MX6QDL_PAD_CSI0_DAT18__IPU1_CSI0_DATA18 0x80000000 - MX6QDL_PAD_CSI0_DAT19__IPU1_CSI0_DATA19 0x80000000 - MX6QDL_PAD_CSI0_PIXCLK__IPU1_CSI0_PIXCLK 0x80000000 - MX6QDL_PAD_CSI0_MCLK__IPU1_CSI0_HSYNC 0x80000000 - MX6QDL_PAD_CSI0_VSYNC__IPU1_CSI0_VSYNC 0x80000000 - >; - }; - }; - - mlb { - pinctrl_mlb_1: mlbgrp-1 { - fsl,pins = < - MX6QDL_PAD_GPIO_3__MLB_CLK 0x71 - MX6QDL_PAD_GPIO_6__MLB_SIG 0x71 - MX6QDL_PAD_GPIO_2__MLB_DATA 0x71 - >; - }; - - pinctrl_mlb_2: mlbgrp-2 { - fsl,pins = < - MX6QDL_PAD_ENET_TXD1__MLB_CLK 0x71 - MX6QDL_PAD_GPIO_6__MLB_SIG 0x71 - MX6QDL_PAD_GPIO_2__MLB_DATA 0x71 - >; - }; - }; - - pwm0 { - pinctrl_pwm0_1: pwm0grp-1 { - fsl,pins = < - MX6QDL_PAD_SD1_DAT3__PWM1_OUT 0x1b0b1 - >; - }; - }; - - pwm3 { - pinctrl_pwm3_1: pwm3grp-1 { - fsl,pins = < - MX6QDL_PAD_SD4_DAT1__PWM3_OUT 0x1b0b1 - >; - }; - }; - - spdif { - pinctrl_spdif_1: spdifgrp-1 { - fsl,pins = < - MX6QDL_PAD_KEY_COL3__SPDIF_IN 0x1b0b0 - >; - }; - - pinctrl_spdif_2: spdifgrp-2 { - fsl,pins = < - MX6QDL_PAD_GPIO_16__SPDIF_IN 0x1b0b0 - MX6QDL_PAD_GPIO_17__SPDIF_OUT 0x1b0b0 - >; - }; - - pinctrl_spdif_3: spdifgrp-3 { - fsl,pins = < - MX6QDL_PAD_ENET_RXD0__SPDIF_OUT 0x1b0b0 - >; - }; - }; - - uart1 { - pinctrl_uart1_1: uart1grp-1 { - fsl,pins = < - MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1 - MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1 - >; - }; - }; - - uart2 { - pinctrl_uart2_1: uart2grp-1 { - fsl,pins = < - MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1 - MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1 - >; - }; - - pinctrl_uart2_2: uart2grp-2 { /* DTE mode */ - fsl,pins = < - MX6QDL_PAD_EIM_D26__UART2_RX_DATA 0x1b0b1 - MX6QDL_PAD_EIM_D27__UART2_TX_DATA 0x1b0b1 - MX6QDL_PAD_EIM_D28__UART2_DTE_CTS_B 0x1b0b1 - MX6QDL_PAD_EIM_D29__UART2_DTE_RTS_B 0x1b0b1 - >; - }; - }; - - uart3 { - pinctrl_uart3_1: uart3grp-1 { - fsl,pins = < - MX6QDL_PAD_SD4_CLK__UART3_RX_DATA 0x1b0b1 - MX6QDL_PAD_SD4_CMD__UART3_TX_DATA 0x1b0b1 - MX6QDL_PAD_EIM_D30__UART3_CTS_B 0x1b0b1 - MX6QDL_PAD_EIM_EB3__UART3_RTS_B 0x1b0b1 - >; - }; - - pinctrl_uart3_2: uart3grp-2 { - fsl,pins = < - MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1 - MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1 - MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1 - MX6QDL_PAD_EIM_EB3__UART3_RTS_B 0x1b0b1 - >; - }; - }; - - uart4 { - pinctrl_uart4_1: uart4grp-1 { - fsl,pins = < - MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1 - MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1 - >; - }; - }; - - usbotg { - pinctrl_usbotg_1: usbotggrp-1 { - fsl,pins = < - MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059 - >; - }; - - pinctrl_usbotg_2: usbotggrp-2 { - fsl,pins = < - MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x17059 - >; - }; - }; - - usbh2 { - pinctrl_usbh2_1: usbh2grp-1 { - fsl,pins = < - MX6QDL_PAD_RGMII_TXC__USB_H2_DATA 0x40013030 - MX6QDL_PAD_RGMII_TX_CTL__USB_H2_STROBE 0x40013030 - >; - }; - - pinctrl_usbh2_2: usbh2grp-2 { - fsl,pins = < - MX6QDL_PAD_RGMII_TX_CTL__USB_H2_STROBE 0x40017030 - >; - }; - }; - - usbh3 { - pinctrl_usbh3_1: usbh3grp-1 { - fsl,pins = < - MX6QDL_PAD_RGMII_RX_CTL__USB_H3_DATA 0x40013030 - MX6QDL_PAD_RGMII_RXC__USB_H3_STROBE 0x40013030 - >; - }; - - pinctrl_usbh3_2: usbh3grp-2 { - fsl,pins = < - MX6QDL_PAD_RGMII_RXC__USB_H3_STROBE 0x40017030 - >; - }; - }; - - usdhc1 { - pinctrl_usdhc1_1: usdhc1grp-1 { - fsl,pins = < - MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059 - MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059 - MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059 - MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059 - MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059 - MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059 - MX6QDL_PAD_NANDF_D0__SD1_DATA4 0x17059 - MX6QDL_PAD_NANDF_D1__SD1_DATA5 0x17059 - MX6QDL_PAD_NANDF_D2__SD1_DATA6 0x17059 - MX6QDL_PAD_NANDF_D3__SD1_DATA7 0x17059 - >; - }; - - pinctrl_usdhc1_2: usdhc1grp-2 { - fsl,pins = < - MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059 - MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059 - MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059 - MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059 - MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059 - MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059 - >; - }; - }; - - usdhc2 { - pinctrl_usdhc2_1: usdhc2grp-1 { - fsl,pins = < - MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 - MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 - MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 - MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 - MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 - MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 - MX6QDL_PAD_NANDF_D4__SD2_DATA4 0x17059 - MX6QDL_PAD_NANDF_D5__SD2_DATA5 0x17059 - MX6QDL_PAD_NANDF_D6__SD2_DATA6 0x17059 - MX6QDL_PAD_NANDF_D7__SD2_DATA7 0x17059 - >; - }; - - pinctrl_usdhc2_2: usdhc2grp-2 { - fsl,pins = < - MX6QDL_PAD_SD2_CMD__SD2_CMD 0x17059 - MX6QDL_PAD_SD2_CLK__SD2_CLK 0x10059 - MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x17059 - MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x17059 - MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x17059 - MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x17059 - >; - }; - }; - - usdhc3 { - pinctrl_usdhc3_1: usdhc3grp-1 { - fsl,pins = < - MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 - MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 - MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 - MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 - MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 - MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 - MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x17059 - MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x17059 - MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x17059 - MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x17059 - >; - }; - - pinctrl_usdhc3_1_100mhz: usdhc3grp-1-100mhz { /* 100Mhz */ - fsl,pins = < - MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170b9 - MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100b9 - MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170b9 - MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170b9 - MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170b9 - MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170b9 - MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170b9 - MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170b9 - MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170b9 - MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170b9 - >; - }; - - pinctrl_usdhc3_1_200mhz: usdhc3grp-1-200mhz { /* 200Mhz */ - fsl,pins = < - MX6QDL_PAD_SD3_CMD__SD3_CMD 0x170f9 - MX6QDL_PAD_SD3_CLK__SD3_CLK 0x100f9 - MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x170f9 - MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x170f9 - MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x170f9 - MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x170f9 - MX6QDL_PAD_SD3_DAT4__SD3_DATA4 0x170f9 - MX6QDL_PAD_SD3_DAT5__SD3_DATA5 0x170f9 - MX6QDL_PAD_SD3_DAT6__SD3_DATA6 0x170f9 - MX6QDL_PAD_SD3_DAT7__SD3_DATA7 0x170f9 - >; - }; - - pinctrl_usdhc3_2: usdhc3grp-2 { - fsl,pins = < - MX6QDL_PAD_SD3_CMD__SD3_CMD 0x17059 - MX6QDL_PAD_SD3_CLK__SD3_CLK 0x10059 - MX6QDL_PAD_SD3_DAT0__SD3_DATA0 0x17059 - MX6QDL_PAD_SD3_DAT1__SD3_DATA1 0x17059 - MX6QDL_PAD_SD3_DAT2__SD3_DATA2 0x17059 - MX6QDL_PAD_SD3_DAT3__SD3_DATA3 0x17059 - >; - }; - }; - - usdhc4 { - pinctrl_usdhc4_1: usdhc4grp-1 { - fsl,pins = < - MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 - MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 - MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 - MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 - MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 - MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 - MX6QDL_PAD_SD4_DAT4__SD4_DATA4 0x17059 - MX6QDL_PAD_SD4_DAT5__SD4_DATA5 0x17059 - MX6QDL_PAD_SD4_DAT6__SD4_DATA6 0x17059 - MX6QDL_PAD_SD4_DAT7__SD4_DATA7 0x17059 - >; - }; - - pinctrl_usdhc4_2: usdhc4grp-2 { - fsl,pins = < - MX6QDL_PAD_SD4_CMD__SD4_CMD 0x17059 - MX6QDL_PAD_SD4_CLK__SD4_CLK 0x10059 - MX6QDL_PAD_SD4_DAT0__SD4_DATA0 0x17059 - MX6QDL_PAD_SD4_DAT1__SD4_DATA1 0x17059 - MX6QDL_PAD_SD4_DAT2__SD4_DATA2 0x17059 - MX6QDL_PAD_SD4_DAT3__SD4_DATA3 0x17059 - >; - }; - }; - - weim { - pinctrl_weim_cs0_1: weim_cs0grp-1 { - fsl,pins = < - MX6QDL_PAD_EIM_CS0__EIM_CS0_B 0xb0b1 - >; - }; - - pinctrl_weim_nor_1: weim_norgrp-1 { - fsl,pins = < - MX6QDL_PAD_EIM_OE__EIM_OE_B 0xb0b1 - MX6QDL_PAD_EIM_RW__EIM_RW 0xb0b1 - MX6QDL_PAD_EIM_WAIT__EIM_WAIT_B 0xb060 - /* data */ - MX6QDL_PAD_EIM_D16__EIM_DATA16 0x1b0b0 - MX6QDL_PAD_EIM_D17__EIM_DATA17 0x1b0b0 - MX6QDL_PAD_EIM_D18__EIM_DATA18 0x1b0b0 - MX6QDL_PAD_EIM_D19__EIM_DATA19 0x1b0b0 - MX6QDL_PAD_EIM_D20__EIM_DATA20 0x1b0b0 - MX6QDL_PAD_EIM_D21__EIM_DATA21 0x1b0b0 - MX6QDL_PAD_EIM_D22__EIM_DATA22 0x1b0b0 - MX6QDL_PAD_EIM_D23__EIM_DATA23 0x1b0b0 - MX6QDL_PAD_EIM_D24__EIM_DATA24 0x1b0b0 - MX6QDL_PAD_EIM_D25__EIM_DATA25 0x1b0b0 - MX6QDL_PAD_EIM_D26__EIM_DATA26 0x1b0b0 - MX6QDL_PAD_EIM_D27__EIM_DATA27 0x1b0b0 - MX6QDL_PAD_EIM_D28__EIM_DATA28 0x1b0b0 - MX6QDL_PAD_EIM_D29__EIM_DATA29 0x1b0b0 - MX6QDL_PAD_EIM_D30__EIM_DATA30 0x1b0b0 - MX6QDL_PAD_EIM_D31__EIM_DATA31 0x1b0b0 - /* address */ - MX6QDL_PAD_EIM_A23__EIM_ADDR23 0xb0b1 - MX6QDL_PAD_EIM_A22__EIM_ADDR22 0xb0b1 - MX6QDL_PAD_EIM_A21__EIM_ADDR21 0xb0b1 - MX6QDL_PAD_EIM_A20__EIM_ADDR20 0xb0b1 - MX6QDL_PAD_EIM_A19__EIM_ADDR19 0xb0b1 - MX6QDL_PAD_EIM_A18__EIM_ADDR18 0xb0b1 - MX6QDL_PAD_EIM_A17__EIM_ADDR17 0xb0b1 - MX6QDL_PAD_EIM_A16__EIM_ADDR16 0xb0b1 - MX6QDL_PAD_EIM_DA15__EIM_AD15 0xb0b1 - MX6QDL_PAD_EIM_DA14__EIM_AD14 0xb0b1 - MX6QDL_PAD_EIM_DA13__EIM_AD13 0xb0b1 - MX6QDL_PAD_EIM_DA12__EIM_AD12 0xb0b1 - MX6QDL_PAD_EIM_DA11__EIM_AD11 0xb0b1 - MX6QDL_PAD_EIM_DA10__EIM_AD10 0xb0b1 - MX6QDL_PAD_EIM_DA9__EIM_AD09 0xb0b1 - MX6QDL_PAD_EIM_DA8__EIM_AD08 0xb0b1 - MX6QDL_PAD_EIM_DA7__EIM_AD07 0xb0b1 - MX6QDL_PAD_EIM_DA6__EIM_AD06 0xb0b1 - MX6QDL_PAD_EIM_DA5__EIM_AD05 0xb0b1 - MX6QDL_PAD_EIM_DA4__EIM_AD04 0xb0b1 - MX6QDL_PAD_EIM_DA3__EIM_AD03 0xb0b1 - MX6QDL_PAD_EIM_DA2__EIM_AD02 0xb0b1 - MX6QDL_PAD_EIM_DA1__EIM_AD01 0xb0b1 - MX6QDL_PAD_EIM_DA0__EIM_AD00 0xb0b1 - >; - }; - }; }; ldb: ldb@020e0008 { @@ -1433,18 +739,18 @@ dcic1: dcic@020e4000 { reg = <0x020e4000 0x4000>; - interrupts = <0 124 0x04>; + interrupts = <0 124 IRQ_TYPE_LEVEL_HIGH>; }; dcic2: dcic@020e8000 { reg = <0x020e8000 0x4000>; - interrupts = <0 125 0x04>; + interrupts = <0 125 IRQ_TYPE_LEVEL_HIGH>; }; sdma: sdma@020ec000 { compatible = "fsl,imx6q-sdma", "fsl,imx35-sdma"; reg = <0x020ec000 0x4000>; - interrupts = <0 2 0x04>; + interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 155>, <&clks 155>; clock-names = "ipg", "ahb"; #dma-cells = <3>; @@ -1461,7 +767,8 @@ caam@02100000 { reg = <0x02100000 0x40000>; - interrupts = <0 105 0x04 0 106 0x04>; + interrupts = <0 105 IRQ_TYPE_LEVEL_HIGH>, + <0 106 IRQ_TYPE_LEVEL_HIGH>; }; aipstz@0217c000 { /* AIPSTZ2 */ @@ -1471,7 +778,7 @@ usbotg: usb@02184000 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; reg = <0x02184000 0x200>; - interrupts = <0 43 0x04>; + interrupts = <0 43 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 162>; fsl,usbphy = <&usbphy1>; fsl,usbmisc = <&usbmisc 0>; @@ -1481,7 +788,7 @@ usbh1: usb@02184200 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; reg = <0x02184200 0x200>; - interrupts = <0 40 0x04>; + interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 162>; fsl,usbphy = <&usbphy2>; fsl,usbmisc = <&usbmisc 1>; @@ -1491,7 +798,7 @@ usbh2: usb@02184400 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; reg = <0x02184400 0x200>; - interrupts = <0 41 0x04>; + interrupts = <0 41 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 162>; fsl,usbmisc = <&usbmisc 2>; status = "disabled"; @@ -1500,7 +807,7 @@ usbh3: usb@02184600 { compatible = "fsl,imx6q-usb", "fsl,imx27-usb"; reg = <0x02184600 0x200>; - interrupts = <0 42 0x04>; + interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 162>; fsl,usbmisc = <&usbmisc 3>; status = "disabled"; @@ -1516,7 +823,9 @@ fec: ethernet@02188000 { compatible = "fsl,imx6q-fec"; reg = <0x02188000 0x4000>; - interrupts = <0 118 0x04 0 119 0x04>; + interrupts-extended = + <&intc 0 118 IRQ_TYPE_LEVEL_HIGH>, + <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 117>, <&clks 117>, <&clks 190>; clock-names = "ipg", "ahb", "ptp"; status = "disabled"; @@ -1524,13 +833,15 @@ mlb@0218c000 { reg = <0x0218c000 0x4000>; - interrupts = <0 53 0x04 0 117 0x04 0 126 0x04>; + interrupts = <0 53 IRQ_TYPE_LEVEL_HIGH>, + <0 117 IRQ_TYPE_LEVEL_HIGH>, + <0 126 IRQ_TYPE_LEVEL_HIGH>; }; usdhc1: usdhc@02190000 { compatible = "fsl,imx6q-usdhc"; reg = <0x02190000 0x4000>; - interrupts = <0 22 0x04>; + interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 163>, <&clks 163>, <&clks 163>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; @@ -1540,7 +851,7 @@ usdhc2: usdhc@02194000 { compatible = "fsl,imx6q-usdhc"; reg = <0x02194000 0x4000>; - interrupts = <0 23 0x04>; + interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 164>, <&clks 164>, <&clks 164>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; @@ -1550,7 +861,7 @@ usdhc3: usdhc@02198000 { compatible = "fsl,imx6q-usdhc"; reg = <0x02198000 0x4000>; - interrupts = <0 24 0x04>; + interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 165>, <&clks 165>, <&clks 165>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; @@ -1560,7 +871,7 @@ usdhc4: usdhc@0219c000 { compatible = "fsl,imx6q-usdhc"; reg = <0x0219c000 0x4000>; - interrupts = <0 25 0x04>; + interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 166>, <&clks 166>, <&clks 166>; clock-names = "ipg", "ahb", "per"; bus-width = <4>; @@ -1572,7 +883,7 @@ #size-cells = <0>; compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c"; reg = <0x021a0000 0x4000>; - interrupts = <0 36 0x04>; + interrupts = <0 36 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 125>; status = "disabled"; }; @@ -1582,7 +893,7 @@ #size-cells = <0>; compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c"; reg = <0x021a4000 0x4000>; - interrupts = <0 37 0x04>; + interrupts = <0 37 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 126>; status = "disabled"; }; @@ -1592,7 +903,7 @@ #size-cells = <0>; compatible = "fsl,imx6q-i2c", "fsl,imx21-i2c"; reg = <0x021a8000 0x4000>; - interrupts = <0 38 0x04>; + interrupts = <0 38 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 127>; status = "disabled"; }; @@ -1613,7 +924,7 @@ weim: weim@021b8000 { compatible = "fsl,imx6q-weim"; reg = <0x021b8000 0x4000>; - interrupts = <0 14 0x04>; + interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 196>; }; @@ -1624,12 +935,12 @@ tzasc@021d0000 { /* TZASC1 */ reg = <0x021d0000 0x4000>; - interrupts = <0 108 0x04>; + interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; }; tzasc@021d4000 { /* TZASC2 */ reg = <0x021d4000 0x4000>; - interrupts = <0 109 0x04>; + interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH>; }; audmux: audmux@021d8000 { @@ -1638,7 +949,7 @@ status = "disabled"; }; - mipi@021dc000 { /* MIPI-CSI */ + mipi_csi: mipi@021dc000 { reg = <0x021dc000 0x4000>; }; @@ -1667,13 +978,13 @@ vdoa@021e4000 { reg = <0x021e4000 0x4000>; - interrupts = <0 18 0x04>; + interrupts = <0 18 IRQ_TYPE_LEVEL_HIGH>; }; uart2: serial@021e8000 { compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x021e8000 0x4000>; - interrupts = <0 27 0x04>; + interrupts = <0 27 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 160>, <&clks 161>; clock-names = "ipg", "per"; dmas = <&sdma 27 4 0>, <&sdma 28 4 0>; @@ -1684,7 +995,7 @@ uart3: serial@021ec000 { compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x021ec000 0x4000>; - interrupts = <0 28 0x04>; + interrupts = <0 28 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 160>, <&clks 161>; clock-names = "ipg", "per"; dmas = <&sdma 29 4 0>, <&sdma 30 4 0>; @@ -1695,7 +1006,7 @@ uart4: serial@021f0000 { compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x021f0000 0x4000>; - interrupts = <0 29 0x04>; + interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 160>, <&clks 161>; clock-names = "ipg", "per"; dmas = <&sdma 31 4 0>, <&sdma 32 4 0>; @@ -1706,7 +1017,7 @@ uart5: serial@021f4000 { compatible = "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x021f4000 0x4000>; - interrupts = <0 30 0x04>; + interrupts = <0 30 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 160>, <&clks 161>; clock-names = "ipg", "per"; dmas = <&sdma 33 4 0>, <&sdma 34 4 0>; @@ -1720,7 +1031,8 @@ #size-cells = <0>; compatible = "fsl,imx6q-ipu"; reg = <0x02400000 0x400000>; - interrupts = <0 6 0x4 0 5 0x4>; + interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>, + <0 5 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks 130>, <&clks 131>, <&clks 132>; clock-names = "bus", "di0", "di1"; resets = <&src 2>; diff --git a/arch/arm/boot/dts/imx6sl-evk.dts b/arch/arm/boot/dts/imx6sl-evk.dts index cc68e19c5163..864d8dfb51ca 100644 --- a/arch/arm/boot/dts/imx6sl-evk.dts +++ b/arch/arm/boot/dts/imx6sl-evk.dts @@ -8,6 +8,8 @@ /dts-v1/; +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> #include "imx6sl.dtsi" / { @@ -18,11 +20,26 @@ reg = <0x80000000 0x40000000>; }; + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_led>; + + user { + label = "debug"; + gpios = <&gpio3 20 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + }; + regulators { compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; - reg_usb_otg1_vbus: usb_otg1_vbus { + reg_usb_otg1_vbus: regulator@0 { compatible = "regulator-fixed"; + reg = <0>; regulator-name = "usb_otg1_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; @@ -30,22 +47,63 @@ enable-active-high; }; - reg_usb_otg2_vbus: usb_otg2_vbus { + reg_usb_otg2_vbus: regulator@1 { compatible = "regulator-fixed"; + reg = <1>; regulator-name = "usb_otg2_vbus"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; gpio = <&gpio4 2 0>; enable-active-high; }; + + reg_aud3v: regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "wm8962-supply-3v15"; + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3150000>; + regulator-boot-on; + }; + + reg_aud4v: regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "wm8962-supply-4v2"; + regulator-min-microvolt = <4325000>; + regulator-max-microvolt = <4325000>; + regulator-boot-on; + }; + }; + + sound { + compatible = "fsl,imx6sl-evk-wm8962", "fsl,imx-audio-wm8962"; + model = "wm8962-audio"; + ssi-controller = <&ssi2>; + audio-codec = <&codec>; + audio-routing = + "Headphone Jack", "HPOUTL", + "Headphone Jack", "HPOUTR", + "Ext Spk", "SPKOUTL", + "Ext Spk", "SPKOUTR", + "AMIC", "MICBIAS", + "IN3R", "AMIC"; + mux-int-port = <2>; + mux-ext-port = <3>; }; }; +&audmux { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_audmux3>; + status = "okay"; +}; + &ecspi1 { fsl,spi-num-chipselects = <1>; cs-gpios = <&gpio4 11 0>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_ecspi1_1>; + pinctrl-0 = <&pinctrl_ecspi1>; status = "okay"; flash: m25p80@0 { @@ -59,16 +117,144 @@ &fec { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec_1>; + pinctrl-0 = <&pinctrl_fec>; phy-mode = "rmii"; status = "okay"; }; +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic: pfuze100@08 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + regulator-always-on; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + codec: wm8962@1a { + compatible = "wlf,wm8962"; + reg = <0x1a>; + clocks = <&clks IMX6SL_CLK_EXTERN_AUDIO>; + DCVDD-supply = <&vgen3_reg>; + DBVDD-supply = <®_aud3v>; + AVDD-supply = <&vgen3_reg>; + CPVDD-supply = <&vgen3_reg>; + MICVDD-supply = <®_aud3v>; + PLLVDD-supply = <&vgen3_reg>; + SPKVDD1-supply = <®_aud4v>; + SPKVDD2-supply = <®_aud4v>; + }; +}; + &iomuxc { pinctrl-names = "default"; pinctrl-0 = <&pinctrl_hog>; - hog { + imx6sl-evk { pinctrl_hog: hoggrp { fsl,pins = < MX6SL_PAD_KEY_ROW7__GPIO4_IO07 0x17059 @@ -78,21 +264,230 @@ MX6SL_PAD_REF_CLK_32K__GPIO3_IO22 0x17059 MX6SL_PAD_KEY_COL4__GPIO4_IO00 0x80000000 MX6SL_PAD_KEY_COL5__GPIO4_IO02 0x80000000 + MX6SL_PAD_AUD_MCLK__AUDIO_CLK_OUT 0x4130b0 + >; + }; + + pinctrl_audmux3: audmux3grp { + fsl,pins = < + MX6SL_PAD_AUD_RXD__AUD3_RXD 0x4130b0 + MX6SL_PAD_AUD_TXC__AUD3_TXC 0x4130b0 + MX6SL_PAD_AUD_TXD__AUD3_TXD 0x4110b0 + MX6SL_PAD_AUD_TXFS__AUD3_TXFS 0x4130b0 + >; + }; + + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX6SL_PAD_ECSPI1_MISO__ECSPI1_MISO 0x100b1 + MX6SL_PAD_ECSPI1_MOSI__ECSPI1_MOSI 0x100b1 + MX6SL_PAD_ECSPI1_SCLK__ECSPI1_SCLK 0x100b1 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX6SL_PAD_FEC_MDC__FEC_MDC 0x1b0b0 + MX6SL_PAD_FEC_MDIO__FEC_MDIO 0x1b0b0 + MX6SL_PAD_FEC_CRS_DV__FEC_RX_DV 0x1b0b0 + MX6SL_PAD_FEC_RXD0__FEC_RX_DATA0 0x1b0b0 + MX6SL_PAD_FEC_RXD1__FEC_RX_DATA1 0x1b0b0 + MX6SL_PAD_FEC_TX_EN__FEC_TX_EN 0x1b0b0 + MX6SL_PAD_FEC_TXD0__FEC_TX_DATA0 0x1b0b0 + MX6SL_PAD_FEC_TXD1__FEC_TX_DATA1 0x1b0b0 + MX6SL_PAD_FEC_REF_CLK__FEC_REF_OUT 0x4001b0a8 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX6SL_PAD_I2C1_SCL__I2C1_SCL 0x4001b8b1 + MX6SL_PAD_I2C1_SDA__I2C1_SDA 0x4001b8b1 + >; + }; + + + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX6SL_PAD_I2C2_SCL__I2C2_SCL 0x4001b8b1 + MX6SL_PAD_I2C2_SDA__I2C2_SDA 0x4001b8b1 + >; + }; + + pinctrl_led: ledgrp { + fsl,pins = < + MX6SL_PAD_HSIC_STROBE__GPIO3_IO20 0x17059 + >; + }; + + pinctrl_kpp: kppgrp { + fsl,pins = < + MX6SL_PAD_KEY_ROW0__KEY_ROW0 0x1b010 + MX6SL_PAD_KEY_ROW1__KEY_ROW1 0x1b010 + MX6SL_PAD_KEY_ROW2__KEY_ROW2 0x1b0b0 + MX6SL_PAD_KEY_COL0__KEY_COL0 0x110b0 + MX6SL_PAD_KEY_COL1__KEY_COL1 0x110b0 + MX6SL_PAD_KEY_COL2__KEY_COL2 0x110b0 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1 + MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1 + >; + }; + + pinctrl_usbotg1: usbotg1grp { + fsl,pins = < + MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059 + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + MX6SL_PAD_SD1_CMD__SD1_CMD 0x17059 + MX6SL_PAD_SD1_CLK__SD1_CLK 0x10059 + MX6SL_PAD_SD1_DAT0__SD1_DATA0 0x17059 + MX6SL_PAD_SD1_DAT1__SD1_DATA1 0x17059 + MX6SL_PAD_SD1_DAT2__SD1_DATA2 0x17059 + MX6SL_PAD_SD1_DAT3__SD1_DATA3 0x17059 + MX6SL_PAD_SD1_DAT4__SD1_DATA4 0x17059 + MX6SL_PAD_SD1_DAT5__SD1_DATA5 0x17059 + MX6SL_PAD_SD1_DAT6__SD1_DATA6 0x17059 + MX6SL_PAD_SD1_DAT7__SD1_DATA7 0x17059 + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1grp100mhz { + fsl,pins = < + MX6SL_PAD_SD1_CMD__SD1_CMD 0x170b9 + MX6SL_PAD_SD1_CLK__SD1_CLK 0x100b9 + MX6SL_PAD_SD1_DAT0__SD1_DATA0 0x170b9 + MX6SL_PAD_SD1_DAT1__SD1_DATA1 0x170b9 + MX6SL_PAD_SD1_DAT2__SD1_DATA2 0x170b9 + MX6SL_PAD_SD1_DAT3__SD1_DATA3 0x170b9 + MX6SL_PAD_SD1_DAT4__SD1_DATA4 0x170b9 + MX6SL_PAD_SD1_DAT5__SD1_DATA5 0x170b9 + MX6SL_PAD_SD1_DAT6__SD1_DATA6 0x170b9 + MX6SL_PAD_SD1_DAT7__SD1_DATA7 0x170b9 + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1grp200mhz { + fsl,pins = < + MX6SL_PAD_SD1_CMD__SD1_CMD 0x170f9 + MX6SL_PAD_SD1_CLK__SD1_CLK 0x100f9 + MX6SL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 + MX6SL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 + MX6SL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 + MX6SL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 + MX6SL_PAD_SD1_DAT4__SD1_DATA4 0x170f9 + MX6SL_PAD_SD1_DAT5__SD1_DATA5 0x170f9 + MX6SL_PAD_SD1_DAT6__SD1_DATA6 0x170f9 + MX6SL_PAD_SD1_DAT7__SD1_DATA7 0x170f9 + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX6SL_PAD_SD2_CMD__SD2_CMD 0x17059 + MX6SL_PAD_SD2_CLK__SD2_CLK 0x10059 + MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x17059 + MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x17059 + MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x17059 + MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x17059 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2grp100mhz { + fsl,pins = < + MX6SL_PAD_SD2_CMD__SD2_CMD 0x170b9 + MX6SL_PAD_SD2_CLK__SD2_CLK 0x100b9 + MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x170b9 + MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x170b9 + MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x170b9 + MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x170b9 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2grp200mhz { + fsl,pins = < + MX6SL_PAD_SD2_CMD__SD2_CMD 0x170f9 + MX6SL_PAD_SD2_CLK__SD2_CLK 0x100f9 + MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x170f9 + MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x170f9 + MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x170f9 + MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x170f9 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX6SL_PAD_SD3_CMD__SD3_CMD 0x17059 + MX6SL_PAD_SD3_CLK__SD3_CLK 0x10059 + MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x17059 + MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x17059 + MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x17059 + MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x17059 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3grp100mhz { + fsl,pins = < + MX6SL_PAD_SD3_CMD__SD3_CMD 0x170b9 + MX6SL_PAD_SD3_CLK__SD3_CLK 0x100b9 + MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x170b9 + MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x170b9 + MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x170b9 + MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x170b9 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3grp200mhz { + fsl,pins = < + MX6SL_PAD_SD3_CMD__SD3_CMD 0x170f9 + MX6SL_PAD_SD3_CLK__SD3_CLK 0x100f9 + MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x170f9 + MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x170f9 + MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x170f9 + MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x170f9 >; }; }; }; +&kpp { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_kpp>; + linux,keymap = < + MATRIX_KEY(0x0, 0x0, KEY_UP) /* ROW0, COL0 */ + MATRIX_KEY(0x0, 0x1, KEY_DOWN) /* ROW0, COL1 */ + MATRIX_KEY(0x0, 0x2, KEY_ENTER) /* ROW0, COL2 */ + MATRIX_KEY(0x1, 0x0, KEY_HOME) /* ROW1, COL0 */ + MATRIX_KEY(0x1, 0x1, KEY_RIGHT) /* ROW1, COL1 */ + MATRIX_KEY(0x1, 0x2, KEY_LEFT) /* ROW1, COL2 */ + MATRIX_KEY(0x2, 0x0, KEY_VOLUMEDOWN) /* ROW2, COL0 */ + MATRIX_KEY(0x2, 0x1, KEY_VOLUMEUP) /* ROW2, COL1 */ + >; + status = "okay"; +}; + +&ssi2 { + fsl,mode = "i2s-slave"; + status = "okay"; +}; + &uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_1>; + pinctrl-0 = <&pinctrl_uart1>; status = "okay"; }; &usbotg1 { vbus-supply = <®_usb_otg1_vbus>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_usbotg1_1>; + pinctrl-0 = <&pinctrl_usbotg1>; disable-over-current; status = "okay"; }; @@ -106,9 +501,9 @@ &usdhc1 { pinctrl-names = "default", "state_100mhz", "state_200mhz"; - pinctrl-0 = <&pinctrl_usdhc1_1>; - pinctrl-1 = <&pinctrl_usdhc1_1_100mhz>; - pinctrl-2 = <&pinctrl_usdhc1_1_200mhz>; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; bus-width = <8>; cd-gpios = <&gpio4 7 0>; wp-gpios = <&gpio4 6 0>; @@ -117,9 +512,9 @@ &usdhc2 { pinctrl-names = "default", "state_100mhz", "state_200mhz"; - pinctrl-0 = <&pinctrl_usdhc2_1>; - pinctrl-1 = <&pinctrl_usdhc2_1_100mhz>; - pinctrl-2 = <&pinctrl_usdhc2_1_200mhz>; + pinctrl-0 = <&pinctrl_usdhc2>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; cd-gpios = <&gpio5 0 0>; wp-gpios = <&gpio4 29 0>; status = "okay"; @@ -127,9 +522,9 @@ &usdhc3 { pinctrl-names = "default", "state_100mhz", "state_200mhz"; - pinctrl-0 = <&pinctrl_usdhc3_1>; - pinctrl-1 = <&pinctrl_usdhc3_1_100mhz>; - pinctrl-2 = <&pinctrl_usdhc3_1_200mhz>; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; cd-gpios = <&gpio3 22 0>; status = "okay"; }; diff --git a/arch/arm/boot/dts/imx6sl.dtsi b/arch/arm/boot/dts/imx6sl.dtsi index 28558f1aaf2d..3cb4941afeef 100644 --- a/arch/arm/boot/dts/imx6sl.dtsi +++ b/arch/arm/boot/dts/imx6sl.dtsi @@ -7,6 +7,7 @@ * */ +#include <dt-bindings/interrupt-controller/irq.h> #include "skeleton.dtsi" #include "imx6sl-pinfunc.h" #include <dt-bindings/clock/imx6sl-clock.h> @@ -27,6 +28,8 @@ spi1 = &ecspi2; spi2 = &ecspi3; spi3 = &ecspi4; + usbphy0 = &usbphy1; + usbphy1 = &usbphy2; }; cpus { @@ -38,6 +41,27 @@ device_type = "cpu"; reg = <0x0>; next-level-cache = <&L2>; + operating-points = < + /* kHz uV */ + 996000 1275000 + 792000 1175000 + 396000 975000 + >; + fsl,soc-operating-points = < + /* ARM kHz SOC-PU uV */ + 996000 1225000 + 792000 1175000 + 396000 1175000 + >; + clock-latency = <61036>; /* two CLK32 periods */ + clocks = <&clks IMX6SL_CLK_ARM>, <&clks IMX6SL_CLK_PLL2_PFD2>, + <&clks IMX6SL_CLK_STEP>, <&clks IMX6SL_CLK_PLL1_SW>, + <&clks IMX6SL_CLK_PLL1_SYS>; + clock-names = "arm", "pll2_pfd2_396m", "step", + "pll1_sw", "pll1_sys"; + arm-supply = <®_arm>; + pu-supply = <®_pu>; + soc-supply = <®_soc>; }; }; @@ -73,10 +97,16 @@ interrupt-parent = <&intc>; ranges; + ocram: sram@00900000 { + compatible = "mmio-sram"; + reg = <0x00900000 0x20000>; + clocks = <&clks IMX6SL_CLK_OCRAM>; + }; + L2: l2-cache@00a02000 { compatible = "arm,pl310-cache"; reg = <0x00a02000 0x1000>; - interrupts = <0 92 0x04>; + interrupts = <0 92 IRQ_TYPE_LEVEL_HIGH>; cache-unified; cache-level = <2>; arm,tag-latency = <4 2 3>; @@ -85,7 +115,7 @@ pmu { compatible = "arm,cortex-a9-pmu"; - interrupts = <0 94 0x04>; + interrupts = <0 94 IRQ_TYPE_LEVEL_HIGH>; }; aips1: aips-bus@02000000 { @@ -104,7 +134,7 @@ spdif: spdif@02004000 { reg = <0x02004000 0x4000>; - interrupts = <0 52 0x04>; + interrupts = <0 52 IRQ_TYPE_LEVEL_HIGH>; }; ecspi1: ecspi@02008000 { @@ -112,7 +142,7 @@ #size-cells = <0>; compatible = "fsl,imx6sl-ecspi", "fsl,imx51-ecspi"; reg = <0x02008000 0x4000>; - interrupts = <0 31 0x04>; + interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_ECSPI1>, <&clks IMX6SL_CLK_ECSPI1>; clock-names = "ipg", "per"; @@ -124,7 +154,7 @@ #size-cells = <0>; compatible = "fsl,imx6sl-ecspi", "fsl,imx51-ecspi"; reg = <0x0200c000 0x4000>; - interrupts = <0 32 0x04>; + interrupts = <0 32 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_ECSPI2>, <&clks IMX6SL_CLK_ECSPI2>; clock-names = "ipg", "per"; @@ -136,7 +166,7 @@ #size-cells = <0>; compatible = "fsl,imx6sl-ecspi", "fsl,imx51-ecspi"; reg = <0x02010000 0x4000>; - interrupts = <0 33 0x04>; + interrupts = <0 33 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_ECSPI3>, <&clks IMX6SL_CLK_ECSPI3>; clock-names = "ipg", "per"; @@ -148,7 +178,7 @@ #size-cells = <0>; compatible = "fsl,imx6sl-ecspi", "fsl,imx51-ecspi"; reg = <0x02014000 0x4000>; - interrupts = <0 34 0x04>; + interrupts = <0 34 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_ECSPI4>, <&clks IMX6SL_CLK_ECSPI4>; clock-names = "ipg", "per"; @@ -159,7 +189,7 @@ compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x02018000 0x4000>; - interrupts = <0 30 0x04>; + interrupts = <0 30 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_UART>, <&clks IMX6SL_CLK_UART_SERIAL>; clock-names = "ipg", "per"; @@ -172,7 +202,7 @@ compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x02020000 0x4000>; - interrupts = <0 26 0x04>; + interrupts = <0 26 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_UART>, <&clks IMX6SL_CLK_UART_SERIAL>; clock-names = "ipg", "per"; @@ -185,7 +215,7 @@ compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x02024000 0x4000>; - interrupts = <0 27 0x04>; + interrupts = <0 27 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_UART>, <&clks IMX6SL_CLK_UART_SERIAL>; clock-names = "ipg", "per"; @@ -195,9 +225,11 @@ }; ssi1: ssi@02028000 { - compatible = "fsl,imx6sl-ssi","fsl,imx21-ssi"; + compatible = "fsl,imx6sl-ssi", + "fsl,imx51-ssi", + "fsl,imx21-ssi"; reg = <0x02028000 0x4000>; - interrupts = <0 46 0x04>; + interrupts = <0 46 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_SSI1>; dmas = <&sdma 37 1 0>, <&sdma 38 1 0>; @@ -207,9 +239,11 @@ }; ssi2: ssi@0202c000 { - compatible = "fsl,imx6sl-ssi","fsl,imx21-ssi"; + compatible = "fsl,imx6sl-ssi", + "fsl,imx51-ssi", + "fsl,imx21-ssi"; reg = <0x0202c000 0x4000>; - interrupts = <0 47 0x04>; + interrupts = <0 47 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_SSI2>; dmas = <&sdma 41 1 0>, <&sdma 42 1 0>; @@ -219,9 +253,11 @@ }; ssi3: ssi@02030000 { - compatible = "fsl,imx6sl-ssi","fsl,imx21-ssi"; + compatible = "fsl,imx6sl-ssi", + "fsl,imx51-ssi", + "fsl,imx21-ssi"; reg = <0x02030000 0x4000>; - interrupts = <0 48 0x04>; + interrupts = <0 48 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_SSI3>; dmas = <&sdma 45 1 0>, <&sdma 46 1 0>; @@ -234,7 +270,7 @@ compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x02034000 0x4000>; - interrupts = <0 28 0x04>; + interrupts = <0 28 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_UART>, <&clks IMX6SL_CLK_UART_SERIAL>; clock-names = "ipg", "per"; @@ -247,7 +283,7 @@ compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; reg = <0x02038000 0x4000>; - interrupts = <0 29 0x04>; + interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_UART>, <&clks IMX6SL_CLK_UART_SERIAL>; clock-names = "ipg", "per"; @@ -261,7 +297,7 @@ #pwm-cells = <2>; compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm"; reg = <0x02080000 0x4000>; - interrupts = <0 83 0x04>; + interrupts = <0 83 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_PWM1>, <&clks IMX6SL_CLK_PWM1>; clock-names = "ipg", "per"; @@ -271,7 +307,7 @@ #pwm-cells = <2>; compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm"; reg = <0x02084000 0x4000>; - interrupts = <0 84 0x04>; + interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_PWM2>, <&clks IMX6SL_CLK_PWM2>; clock-names = "ipg", "per"; @@ -281,7 +317,7 @@ #pwm-cells = <2>; compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm"; reg = <0x02088000 0x4000>; - interrupts = <0 85 0x04>; + interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_PWM3>, <&clks IMX6SL_CLK_PWM3>; clock-names = "ipg", "per"; @@ -291,7 +327,7 @@ #pwm-cells = <2>; compatible = "fsl,imx6sl-pwm", "fsl,imx27-pwm"; reg = <0x0208c000 0x4000>; - interrupts = <0 86 0x04>; + interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_PWM4>, <&clks IMX6SL_CLK_PWM4>; clock-names = "ipg", "per"; @@ -300,7 +336,7 @@ gpt: gpt@02098000 { compatible = "fsl,imx6sl-gpt"; reg = <0x02098000 0x4000>; - interrupts = <0 55 0x04>; + interrupts = <0 55 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_GPT>, <&clks IMX6SL_CLK_GPT_SERIAL>; clock-names = "ipg", "per"; @@ -309,7 +345,8 @@ gpio1: gpio@0209c000 { compatible = "fsl,imx6sl-gpio", "fsl,imx35-gpio"; reg = <0x0209c000 0x4000>; - interrupts = <0 66 0x04 0 67 0x04>; + interrupts = <0 66 IRQ_TYPE_LEVEL_HIGH>, + <0 67 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -319,7 +356,8 @@ gpio2: gpio@020a0000 { compatible = "fsl,imx6sl-gpio", "fsl,imx35-gpio"; reg = <0x020a0000 0x4000>; - interrupts = <0 68 0x04 0 69 0x04>; + interrupts = <0 68 IRQ_TYPE_LEVEL_HIGH>, + <0 69 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -329,7 +367,8 @@ gpio3: gpio@020a4000 { compatible = "fsl,imx6sl-gpio", "fsl,imx35-gpio"; reg = <0x020a4000 0x4000>; - interrupts = <0 70 0x04 0 71 0x04>; + interrupts = <0 70 IRQ_TYPE_LEVEL_HIGH>, + <0 71 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -339,7 +378,8 @@ gpio4: gpio@020a8000 { compatible = "fsl,imx6sl-gpio", "fsl,imx35-gpio"; reg = <0x020a8000 0x4000>; - interrupts = <0 72 0x04 0 73 0x04>; + interrupts = <0 72 IRQ_TYPE_LEVEL_HIGH>, + <0 73 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -349,7 +389,8 @@ gpio5: gpio@020ac000 { compatible = "fsl,imx6sl-gpio", "fsl,imx35-gpio"; reg = <0x020ac000 0x4000>; - interrupts = <0 74 0x04 0 75 0x04>; + interrupts = <0 74 IRQ_TYPE_LEVEL_HIGH>, + <0 75 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -357,21 +398,23 @@ }; kpp: kpp@020b8000 { + compatible = "fsl,imx6sl-kpp", "fsl,imx21-kpp"; reg = <0x020b8000 0x4000>; - interrupts = <0 82 0x04>; + interrupts = <0 82 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks IMX6SL_CLK_DUMMY>; }; wdog1: wdog@020bc000 { compatible = "fsl,imx6sl-wdt", "fsl,imx21-wdt"; reg = <0x020bc000 0x4000>; - interrupts = <0 80 0x04>; + interrupts = <0 80 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_DUMMY>; }; wdog2: wdog@020c0000 { compatible = "fsl,imx6sl-wdt", "fsl,imx21-wdt"; reg = <0x020c0000 0x4000>; - interrupts = <0 81 0x04>; + interrupts = <0 81 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_DUMMY>; status = "disabled"; }; @@ -379,7 +422,8 @@ clks: ccm@020c4000 { compatible = "fsl,imx6sl-ccm"; reg = <0x020c4000 0x4000>; - interrupts = <0 87 0x04 0 88 0x04>; + interrupts = <0 87 IRQ_TYPE_LEVEL_HIGH>, + <0 88 IRQ_TYPE_LEVEL_HIGH>; #clock-cells = <1>; }; @@ -388,7 +432,9 @@ "fsl,imx6q-anatop", "syscon", "simple-bus"; reg = <0x020c8000 0x1000>; - interrupts = <0 49 0x04 0 54 0x04 0 127 0x04>; + interrupts = <0 49 IRQ_TYPE_LEVEL_HIGH>, + <0 54 IRQ_TYPE_LEVEL_HIGH>, + <0 127 IRQ_TYPE_LEVEL_HIGH>; regulator-1p1@110 { compatible = "fsl,anatop-regulator"; @@ -434,7 +480,7 @@ reg_arm: regulator-vddcore@140 { compatible = "fsl,anatop-regulator"; - regulator-name = "cpu"; + regulator-name = "vddarm"; regulator-min-microvolt = <725000>; regulator-max-microvolt = <1450000>; regulator-always-on; @@ -487,15 +533,17 @@ usbphy1: usbphy@020c9000 { compatible = "fsl,imx6sl-usbphy", "fsl,imx23-usbphy"; reg = <0x020c9000 0x1000>; - interrupts = <0 44 0x04>; + interrupts = <0 44 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_USBPHY1>; + fsl,anatop = <&anatop>; }; usbphy2: usbphy@020ca000 { compatible = "fsl,imx6sl-usbphy", "fsl,imx23-usbphy"; reg = <0x020ca000 0x1000>; - interrupts = <0 45 0x04>; + interrupts = <0 45 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_USBPHY2>; + fsl,anatop = <&anatop>; }; snvs@020cc000 { @@ -507,31 +555,33 @@ snvs-rtc-lp@34 { compatible = "fsl,sec-v4.0-mon-rtc-lp"; reg = <0x34 0x58>; - interrupts = <0 19 0x04 0 20 0x04>; + interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>, + <0 20 IRQ_TYPE_LEVEL_HIGH>; }; }; epit1: epit@020d0000 { reg = <0x020d0000 0x4000>; - interrupts = <0 56 0x04>; + interrupts = <0 56 IRQ_TYPE_LEVEL_HIGH>; }; epit2: epit@020d4000 { reg = <0x020d4000 0x4000>; - interrupts = <0 57 0x04>; + interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>; }; src: src@020d8000 { compatible = "fsl,imx6sl-src", "fsl,imx51-src"; reg = <0x020d8000 0x4000>; - interrupts = <0 91 0x04 0 96 0x04>; + interrupts = <0 91 IRQ_TYPE_LEVEL_HIGH>, + <0 96 IRQ_TYPE_LEVEL_HIGH>; #reset-cells = <1>; }; gpc: gpc@020dc000 { compatible = "fsl,imx6sl-gpc", "fsl,imx6q-gpc"; reg = <0x020dc000 0x4000>; - interrupts = <0 89 0x04>; + interrupts = <0 89 IRQ_TYPE_LEVEL_HIGH>; }; gpr: iomuxc-gpr@020e0000 { @@ -543,235 +593,22 @@ iomuxc: iomuxc@020e0000 { compatible = "fsl,imx6sl-iomuxc"; reg = <0x020e0000 0x4000>; - - ecspi1 { - pinctrl_ecspi1_1: ecspi1grp-1 { - fsl,pins = < - MX6SL_PAD_ECSPI1_MISO__ECSPI1_MISO 0x100b1 - MX6SL_PAD_ECSPI1_MOSI__ECSPI1_MOSI 0x100b1 - MX6SL_PAD_ECSPI1_SCLK__ECSPI1_SCLK 0x100b1 - >; - }; - }; - - fec { - pinctrl_fec_1: fecgrp-1 { - fsl,pins = < - MX6SL_PAD_FEC_MDC__FEC_MDC 0x1b0b0 - MX6SL_PAD_FEC_MDIO__FEC_MDIO 0x1b0b0 - MX6SL_PAD_FEC_CRS_DV__FEC_RX_DV 0x1b0b0 - MX6SL_PAD_FEC_RXD0__FEC_RX_DATA0 0x1b0b0 - MX6SL_PAD_FEC_RXD1__FEC_RX_DATA1 0x1b0b0 - MX6SL_PAD_FEC_TX_EN__FEC_TX_EN 0x1b0b0 - MX6SL_PAD_FEC_TXD0__FEC_TX_DATA0 0x1b0b0 - MX6SL_PAD_FEC_TXD1__FEC_TX_DATA1 0x1b0b0 - MX6SL_PAD_FEC_REF_CLK__FEC_REF_OUT 0x4001b0a8 - >; - }; - }; - - uart1 { - pinctrl_uart1_1: uart1grp-1 { - fsl,pins = < - MX6SL_PAD_UART1_RXD__UART1_RX_DATA 0x1b0b1 - MX6SL_PAD_UART1_TXD__UART1_TX_DATA 0x1b0b1 - >; - }; - }; - - usbotg1 { - pinctrl_usbotg1_1: usbotg1grp-1 { - fsl,pins = < - MX6SL_PAD_EPDC_PWRCOM__USB_OTG1_ID 0x17059 - >; - }; - - pinctrl_usbotg1_2: usbotg1grp-2 { - fsl,pins = < - MX6SL_PAD_FEC_RXD0__USB_OTG1_ID 0x17059 - >; - }; - - pinctrl_usbotg1_3: usbotg1grp-3 { - fsl,pins = < - MX6SL_PAD_LCD_DAT1__USB_OTG1_ID 0x17059 - >; - }; - - pinctrl_usbotg1_4: usbotg1grp-4 { - fsl,pins = < - MX6SL_PAD_REF_CLK_32K__USB_OTG1_ID 0x17059 - >; - }; - - pinctrl_usbotg1_5: usbotg1grp-5 { - fsl,pins = < - MX6SL_PAD_SD3_DAT0__USB_OTG1_ID 0x17059 - >; - }; - }; - - usbotg2 { - pinctrl_usbotg2_1: usbotg2grp-1 { - fsl,pins = < - MX6SL_PAD_ECSPI1_SCLK__USB_OTG2_OC 0x17059 - >; - }; - - pinctrl_usbotg2_2: usbotg2grp-2 { - fsl,pins = < - MX6SL_PAD_ECSPI2_SCLK__USB_OTG2_OC 0x17059 - >; - }; - - pinctrl_usbotg2_3: usbotg2grp-3 { - fsl,pins = < - MX6SL_PAD_KEY_ROW5__USB_OTG2_OC 0x17059 - >; - }; - - pinctrl_usbotg2_4: usbotg2grp-4 { - fsl,pins = < - MX6SL_PAD_SD3_DAT2__USB_OTG2_OC 0x17059 - >; - }; - }; - - usdhc1 { - pinctrl_usdhc1_1: usdhc1grp-1 { - fsl,pins = < - MX6SL_PAD_SD1_CMD__SD1_CMD 0x17059 - MX6SL_PAD_SD1_CLK__SD1_CLK 0x10059 - MX6SL_PAD_SD1_DAT0__SD1_DATA0 0x17059 - MX6SL_PAD_SD1_DAT1__SD1_DATA1 0x17059 - MX6SL_PAD_SD1_DAT2__SD1_DATA2 0x17059 - MX6SL_PAD_SD1_DAT3__SD1_DATA3 0x17059 - MX6SL_PAD_SD1_DAT4__SD1_DATA4 0x17059 - MX6SL_PAD_SD1_DAT5__SD1_DATA5 0x17059 - MX6SL_PAD_SD1_DAT6__SD1_DATA6 0x17059 - MX6SL_PAD_SD1_DAT7__SD1_DATA7 0x17059 - >; - }; - - pinctrl_usdhc1_1_100mhz: usdhc1grp-1-100mhz { - fsl,pins = < - MX6SL_PAD_SD1_CMD__SD1_CMD 0x170b9 - MX6SL_PAD_SD1_CLK__SD1_CLK 0x100b9 - MX6SL_PAD_SD1_DAT0__SD1_DATA0 0x170b9 - MX6SL_PAD_SD1_DAT1__SD1_DATA1 0x170b9 - MX6SL_PAD_SD1_DAT2__SD1_DATA2 0x170b9 - MX6SL_PAD_SD1_DAT3__SD1_DATA3 0x170b9 - MX6SL_PAD_SD1_DAT4__SD1_DATA4 0x170b9 - MX6SL_PAD_SD1_DAT5__SD1_DATA5 0x170b9 - MX6SL_PAD_SD1_DAT6__SD1_DATA6 0x170b9 - MX6SL_PAD_SD1_DAT7__SD1_DATA7 0x170b9 - >; - }; - - pinctrl_usdhc1_1_200mhz: usdhc1grp-1-200mhz { - fsl,pins = < - MX6SL_PAD_SD1_CMD__SD1_CMD 0x170f9 - MX6SL_PAD_SD1_CLK__SD1_CLK 0x100f9 - MX6SL_PAD_SD1_DAT0__SD1_DATA0 0x170f9 - MX6SL_PAD_SD1_DAT1__SD1_DATA1 0x170f9 - MX6SL_PAD_SD1_DAT2__SD1_DATA2 0x170f9 - MX6SL_PAD_SD1_DAT3__SD1_DATA3 0x170f9 - MX6SL_PAD_SD1_DAT4__SD1_DATA4 0x170f9 - MX6SL_PAD_SD1_DAT5__SD1_DATA5 0x170f9 - MX6SL_PAD_SD1_DAT6__SD1_DATA6 0x170f9 - MX6SL_PAD_SD1_DAT7__SD1_DATA7 0x170f9 - >; - }; - - - }; - - usdhc2 { - pinctrl_usdhc2_1: usdhc2grp-1 { - fsl,pins = < - MX6SL_PAD_SD2_CMD__SD2_CMD 0x17059 - MX6SL_PAD_SD2_CLK__SD2_CLK 0x10059 - MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x17059 - MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x17059 - MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x17059 - MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x17059 - >; - }; - - pinctrl_usdhc2_1_100mhz: usdhc2grp-1-100mhz { - fsl,pins = < - MX6SL_PAD_SD2_CMD__SD2_CMD 0x170b9 - MX6SL_PAD_SD2_CLK__SD2_CLK 0x100b9 - MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x170b9 - MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x170b9 - MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x170b9 - MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x170b9 - >; - }; - - pinctrl_usdhc2_1_200mhz: usdhc2grp-1-200mhz { - fsl,pins = < - MX6SL_PAD_SD2_CMD__SD2_CMD 0x170f9 - MX6SL_PAD_SD2_CLK__SD2_CLK 0x100f9 - MX6SL_PAD_SD2_DAT0__SD2_DATA0 0x170f9 - MX6SL_PAD_SD2_DAT1__SD2_DATA1 0x170f9 - MX6SL_PAD_SD2_DAT2__SD2_DATA2 0x170f9 - MX6SL_PAD_SD2_DAT3__SD2_DATA3 0x170f9 - >; - }; - - }; - - usdhc3 { - pinctrl_usdhc3_1: usdhc3grp-1 { - fsl,pins = < - MX6SL_PAD_SD3_CMD__SD3_CMD 0x17059 - MX6SL_PAD_SD3_CLK__SD3_CLK 0x10059 - MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x17059 - MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x17059 - MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x17059 - MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x17059 - >; - }; - - pinctrl_usdhc3_1_100mhz: usdhc3grp-1-100mhz { - fsl,pins = < - MX6SL_PAD_SD3_CMD__SD3_CMD 0x170b9 - MX6SL_PAD_SD3_CLK__SD3_CLK 0x100b9 - MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x170b9 - MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x170b9 - MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x170b9 - MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x170b9 - >; - }; - - pinctrl_usdhc3_1_200mhz: usdhc3grp-1-200mhz { - fsl,pins = < - MX6SL_PAD_SD3_CMD__SD3_CMD 0x170f9 - MX6SL_PAD_SD3_CLK__SD3_CLK 0x100f9 - MX6SL_PAD_SD3_DAT0__SD3_DATA0 0x170f9 - MX6SL_PAD_SD3_DAT1__SD3_DATA1 0x170f9 - MX6SL_PAD_SD3_DAT2__SD3_DATA2 0x170f9 - MX6SL_PAD_SD3_DAT3__SD3_DATA3 0x170f9 - >; - }; - }; }; csi: csi@020e4000 { reg = <0x020e4000 0x4000>; - interrupts = <0 7 0x04>; + interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>; }; spdc: spdc@020e8000 { reg = <0x020e8000 0x4000>; - interrupts = <0 6 0x04>; + interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>; }; sdma: sdma@020ec000 { compatible = "fsl,imx6sl-sdma", "fsl,imx35-sdma"; reg = <0x020ec000 0x4000>; - interrupts = <0 2 0x04>; + interrupts = <0 2 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_SDMA>, <&clks IMX6SL_CLK_SDMA>; clock-names = "ipg", "ahb"; @@ -782,22 +619,22 @@ pxp: pxp@020f0000 { reg = <0x020f0000 0x4000>; - interrupts = <0 98 0x04>; + interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>; }; epdc: epdc@020f4000 { reg = <0x020f4000 0x4000>; - interrupts = <0 97 0x04>; + interrupts = <0 97 IRQ_TYPE_LEVEL_HIGH>; }; lcdif: lcdif@020f8000 { reg = <0x020f8000 0x4000>; - interrupts = <0 39 0x04>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; }; dcp: dcp@020fc000 { reg = <0x020fc000 0x4000>; - interrupts = <0 99 0x04>; + interrupts = <0 99 IRQ_TYPE_LEVEL_HIGH>; }; }; @@ -811,7 +648,7 @@ usbotg1: usb@02184000 { compatible = "fsl,imx6sl-usb", "fsl,imx27-usb"; reg = <0x02184000 0x200>; - interrupts = <0 43 0x04>; + interrupts = <0 43 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_USBOH3>; fsl,usbphy = <&usbphy1>; fsl,usbmisc = <&usbmisc 0>; @@ -821,7 +658,7 @@ usbotg2: usb@02184200 { compatible = "fsl,imx6sl-usb", "fsl,imx27-usb"; reg = <0x02184200 0x200>; - interrupts = <0 42 0x04>; + interrupts = <0 42 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_USBOH3>; fsl,usbphy = <&usbphy2>; fsl,usbmisc = <&usbmisc 1>; @@ -831,7 +668,7 @@ usbh: usb@02184400 { compatible = "fsl,imx6sl-usb", "fsl,imx27-usb"; reg = <0x02184400 0x200>; - interrupts = <0 40 0x04>; + interrupts = <0 40 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_USBOH3>; fsl,usbmisc = <&usbmisc 2>; status = "disabled"; @@ -847,7 +684,7 @@ fec: ethernet@02188000 { compatible = "fsl,imx6sl-fec", "fsl,imx25-fec"; reg = <0x02188000 0x4000>; - interrupts = <0 114 0x04>; + interrupts = <0 114 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_ENET_REF>, <&clks IMX6SL_CLK_ENET_REF>; clock-names = "ipg", "ahb"; @@ -857,7 +694,7 @@ usdhc1: usdhc@02190000 { compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc"; reg = <0x02190000 0x4000>; - interrupts = <0 22 0x04>; + interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_USDHC1>, <&clks IMX6SL_CLK_USDHC1>, <&clks IMX6SL_CLK_USDHC1>; @@ -869,7 +706,7 @@ usdhc2: usdhc@02194000 { compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc"; reg = <0x02194000 0x4000>; - interrupts = <0 23 0x04>; + interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_USDHC2>, <&clks IMX6SL_CLK_USDHC2>, <&clks IMX6SL_CLK_USDHC2>; @@ -881,7 +718,7 @@ usdhc3: usdhc@02198000 { compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc"; reg = <0x02198000 0x4000>; - interrupts = <0 24 0x04>; + interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_USDHC3>, <&clks IMX6SL_CLK_USDHC3>, <&clks IMX6SL_CLK_USDHC3>; @@ -893,7 +730,7 @@ usdhc4: usdhc@0219c000 { compatible = "fsl,imx6sl-usdhc", "fsl,imx6q-usdhc"; reg = <0x0219c000 0x4000>; - interrupts = <0 25 0x04>; + interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_USDHC4>, <&clks IMX6SL_CLK_USDHC4>, <&clks IMX6SL_CLK_USDHC4>; @@ -907,7 +744,7 @@ #size-cells = <0>; compatible = "fsl,imx6sl-i2c", "fsl,imx21-i2c"; reg = <0x021a0000 0x4000>; - interrupts = <0 36 0x04>; + interrupts = <0 36 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_I2C1>; status = "disabled"; }; @@ -917,7 +754,7 @@ #size-cells = <0>; compatible = "fsl,imx6sl-i2c", "fsl,imx21-i2c"; reg = <0x021a4000 0x4000>; - interrupts = <0 37 0x04>; + interrupts = <0 37 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_I2C2>; status = "disabled"; }; @@ -927,7 +764,7 @@ #size-cells = <0>; compatible = "fsl,imx6sl-i2c", "fsl,imx21-i2c"; reg = <0x021a8000 0x4000>; - interrupts = <0 38 0x04>; + interrupts = <0 38 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks IMX6SL_CLK_I2C3>; status = "disabled"; }; @@ -939,12 +776,12 @@ rngb: rngb@021b4000 { reg = <0x021b4000 0x4000>; - interrupts = <0 5 0x04>; + interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>; }; weim: weim@021b8000 { reg = <0x021b8000 0x4000>; - interrupts = <0 14 0x04>; + interrupts = <0 14 IRQ_TYPE_LEVEL_HIGH>; }; ocotp: ocotp@021bc000 { diff --git a/arch/arm/boot/dts/k2e-clocks.dtsi b/arch/arm/boot/dts/k2e-clocks.dtsi new file mode 100644 index 000000000000..90774d604bc1 --- /dev/null +++ b/arch/arm/boot/dts/k2e-clocks.dtsi @@ -0,0 +1,78 @@ +/* + * Copyright 2014 Texas Instruments, Inc. + * + * Keystone 2 Edison SoC specific device tree + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +clocks { + mainpllclk: mainpllclk@2310110 { + #clock-cells = <0>; + compatible = "ti,keystone,main-pll-clock"; + clocks = <&refclksys>; + reg = <0x02620350 4>, <0x02310110 4>; + reg-names = "control", "multiplier"; + fixed-postdiv = <2>; + }; + + papllclk: papllclk@2620358 { + #clock-cells = <0>; + compatible = "ti,keystone,pll-clock"; + clocks = <&refclkpass>; + clock-output-names = "pa-pll-clk"; + reg = <0x02620358 4>; + reg-names = "control"; + }; + + ddr3apllclk: ddr3apllclk@2620360 { + #clock-cells = <0>; + compatible = "ti,keystone,pll-clock"; + clocks = <&refclkddr3a>; + clock-output-names = "ddr-3a-pll-clk"; + reg = <0x02620360 4>; + reg-names = "control"; + }; + + clkusb1: clkusb1 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk16>; + clock-output-names = "usb"; + reg = <0x02350004 0xb00>, <0x02350000 0x400>; + reg-names = "control", "domain"; + domain-id = <0>; + }; + + clkhyperlink0: clkhyperlink0 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk12>; + clock-output-names = "hyperlink-0"; + reg = <0x02350030 0xb00>, <0x02350014 0x400>; + reg-names = "control", "domain"; + domain-id = <5>; + }; + + clkpcie1: clkpcie1 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk12>; + clock-output-names = "pcie"; + reg = <0x0235006c 0xb00>, <0x02350000 0x400>; + reg-names = "control", "domain"; + domain-id = <18>; + }; + + clkxge: clkxge { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "xge"; + reg = <0x023500c8 0xb00>, <0x02350074 0x400>; + reg-names = "control", "domain"; + domain-id = <29>; + }; +}; diff --git a/arch/arm/boot/dts/k2e-evm.dts b/arch/arm/boot/dts/k2e-evm.dts new file mode 100644 index 000000000000..74b3b63e94cf --- /dev/null +++ b/arch/arm/boot/dts/k2e-evm.dts @@ -0,0 +1,60 @@ +/* + * Copyright 2013-2014 Texas Instruments, Inc. + * + * Keystone 2 Edison EVM device tree + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "keystone.dtsi" +#include "k2e.dtsi" + +/ { + compatible = "ti,k2e-evm","ti,keystone"; + model = "Texas Instruments Keystone 2 Edison EVM"; + + soc { + + clocks { + refclksys: refclksys { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <100000000>; + clock-output-names = "refclk-sys"; + }; + + refclkpass: refclkpass { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <100000000>; + clock-output-names = "refclk-pass"; + }; + + refclkddr3a: refclkddr3a { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <100000000>; + clock-output-names = "refclk-ddr3a"; + }; + }; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; +}; + +&usb1_phy { + status = "okay"; +}; + +&usb1 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/k2e.dtsi b/arch/arm/boot/dts/k2e.dtsi new file mode 100644 index 000000000000..03d01909525b --- /dev/null +++ b/arch/arm/boot/dts/k2e.dtsi @@ -0,0 +1,80 @@ +/* + * Copyright 2013-2014 Texas Instruments, Inc. + * + * Keystone 2 Edison soc device tree + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&gic>; + + cpu@0 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <0>; + }; + + cpu@1 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <1>; + }; + + cpu@2 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <2>; + }; + + cpu@3 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <3>; + }; + }; + + soc { + /include/ "k2e-clocks.dtsi" + + usb: usb@2680000 { + interrupts = <GIC_SPI 152 IRQ_TYPE_EDGE_RISING>; + dwc3@2690000 { + interrupts = <GIC_SPI 152 IRQ_TYPE_EDGE_RISING>; + }; + }; + + usb1_phy: usb_phy@2620750 { + compatible = "ti,keystone-usbphy"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x2620750 24>; + status = "disabled"; + }; + + usb1: usb@25000000 { + compatible = "ti,keystone-dwc3"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x25000000 0x10000>; + clocks = <&clkusb1>; + clock-names = "usb"; + interrupts = <GIC_SPI 414 IRQ_TYPE_EDGE_RISING>; + ranges; + status = "disabled"; + + dwc3@25010000 { + compatible = "synopsys,dwc3"; + reg = <0x25010000 0x70000>; + interrupts = <GIC_SPI 414 IRQ_TYPE_EDGE_RISING>; + usb-phy = <&usb1_phy>, <&usb1_phy>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/k2hk-clocks.dtsi b/arch/arm/boot/dts/k2hk-clocks.dtsi new file mode 100644 index 000000000000..96e65365afe3 --- /dev/null +++ b/arch/arm/boot/dts/k2hk-clocks.dtsi @@ -0,0 +1,426 @@ +/* + * Copyright 2013-2014 Texas Instruments, Inc. + * + * Keystone 2 Kepler/Hawking SoC clock nodes + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +clocks { + armpllclk: armpllclk@2620370 { + #clock-cells = <0>; + compatible = "ti,keystone,pll-clock"; + clocks = <&refclkarm>; + clock-output-names = "arm-pll-clk"; + reg = <0x02620370 4>; + reg-names = "control"; + }; + + mainpllclk: mainpllclk@2310110 { + #clock-cells = <0>; + compatible = "ti,keystone,main-pll-clock"; + clocks = <&refclksys>; + reg = <0x02620350 4>, <0x02310110 4>; + reg-names = "control", "multiplier"; + fixed-postdiv = <2>; + }; + + papllclk: papllclk@2620358 { + #clock-cells = <0>; + compatible = "ti,keystone,pll-clock"; + clocks = <&refclkpass>; + clock-output-names = "pa-pll-clk"; + reg = <0x02620358 4>; + reg-names = "control"; + }; + + ddr3apllclk: ddr3apllclk@2620360 { + #clock-cells = <0>; + compatible = "ti,keystone,pll-clock"; + clocks = <&refclkddr3a>; + clock-output-names = "ddr-3a-pll-clk"; + reg = <0x02620360 4>; + reg-names = "control"; + }; + + ddr3bpllclk: ddr3bpllclk@2620368 { + #clock-cells = <0>; + compatible = "ti,keystone,pll-clock"; + clocks = <&refclkddr3b>; + clock-output-names = "ddr-3b-pll-clk"; + reg = <0x02620368 4>; + reg-names = "control"; + }; + + clktsip: clktsip { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk16>; + clock-output-names = "tsip"; + reg = <0x02350000 0xb00>, <0x02350000 0x400>; + reg-names = "control", "domain"; + domain-id = <0>; + }; + + clksrio: clksrio { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk1rstiso13>; + clock-output-names = "srio"; + reg = <0x0235002c 0xb00>, <0x02350010 0x400>; + reg-names = "control", "domain"; + domain-id = <4>; + }; + + clkhyperlink0: clkhyperlink0 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk12>; + clock-output-names = "hyperlink-0"; + reg = <0x02350030 0xb00>, <0x02350014 0x400>; + reg-names = "control", "domain"; + domain-id = <5>; + }; + + clkgem1: clkgem1 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk1>; + clock-output-names = "gem1"; + reg = <0x02350040 0xb00>, <0x02350024 0x400>; + reg-names = "control", "domain"; + domain-id = <9>; + }; + + clkgem2: clkgem2 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk1>; + clock-output-names = "gem2"; + reg = <0x02350044 0xb00>, <0x02350028 0x400>; + reg-names = "control", "domain"; + domain-id = <10>; + }; + + clkgem3: clkgem3 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk1>; + clock-output-names = "gem3"; + reg = <0x02350048 0xb00>, <0x0235002c 0x400>; + reg-names = "control", "domain"; + domain-id = <11>; + }; + + clkgem4: clkgem4 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk1>; + clock-output-names = "gem4"; + reg = <0x0235004c 0xb00>, <0x02350030 0x400>; + reg-names = "control", "domain"; + domain-id = <12>; + }; + + clkgem5: clkgem5 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk1>; + clock-output-names = "gem5"; + reg = <0x02350050 0xb00>, <0x02350034 0x400>; + reg-names = "control", "domain"; + domain-id = <13>; + }; + + clkgem6: clkgem6 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk1>; + clock-output-names = "gem6"; + reg = <0x02350054 0xb00>, <0x02350038 0x400>; + reg-names = "control", "domain"; + domain-id = <14>; + }; + + clkgem7: clkgem7 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk1>; + clock-output-names = "gem7"; + reg = <0x02350058 0xb00>, <0x0235003c 0x400>; + reg-names = "control", "domain"; + domain-id = <15>; + }; + + clkddr31: clkddr31 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "ddr3-1"; + reg = <0x02350060 0xb00>, <0x02350040 0x400>; + reg-names = "control", "domain"; + domain-id = <16>; + }; + + clktac: clktac { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "tac"; + reg = <0x02350064 0xb00>, <0x02350044 0x400>; + reg-names = "control", "domain"; + domain-id = <17>; + }; + + clkrac01: clkrac01 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "rac-01"; + reg = <0x02350068 0xb00>, <0x02350044 0x400>; + reg-names = "control", "domain"; + domain-id = <17>; + }; + + clkrac23: clkrac23 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "rac-23"; + reg = <0x0235006c 0xb00>, <0x02350048 0x400>; + reg-names = "control", "domain"; + domain-id = <18>; + }; + + clkfftc0: clkfftc0 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "fftc-0"; + reg = <0x02350070 0xb00>, <0x0235004c 0x400>; + reg-names = "control", "domain"; + domain-id = <19>; + }; + + clkfftc1: clkfftc1 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "fftc-1"; + reg = <0x02350074 0xb00>, <0x0235004c 0x400>; + reg-names = "control", "domain"; + domain-id = <19>; + }; + + clkfftc2: clkfftc2 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "fftc-2"; + reg = <0x02350078 0xb00>, <0x02350050 0x400>; + reg-names = "control", "domain"; + domain-id = <20>; + }; + + clkfftc3: clkfftc3 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "fftc-3"; + reg = <0x0235007c 0xb00>, <0x02350050 0x400>; + reg-names = "control", "domain"; + domain-id = <20>; + }; + + clkfftc4: clkfftc4 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "fftc-4"; + reg = <0x02350080 0xb00>, <0x02350050 0x400>; + reg-names = "control", "domain"; + domain-id = <20>; + }; + + clkfftc5: clkfftc5 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "fftc-5"; + reg = <0x02350084 0xb00>, <0x02350050 0x400>; + reg-names = "control", "domain"; + domain-id = <20>; + }; + + clkaif: clkaif { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "aif"; + reg = <0x02350088 0xb00>, <0x02350054 0x400>; + reg-names = "control", "domain"; + domain-id = <21>; + }; + + clktcp3d0: clktcp3d0 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "tcp3d-0"; + reg = <0x0235008c 0xb00>, <0x02350058 0x400>; + reg-names = "control", "domain"; + domain-id = <22>; + }; + + clktcp3d1: clktcp3d1 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "tcp3d-1"; + reg = <0x02350090 0xb00>, <0x02350058 0x400>; + reg-names = "control", "domain"; + domain-id = <22>; + }; + + clktcp3d2: clktcp3d2 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "tcp3d-2"; + reg = <0x02350094 0xb00>, <0x0235005c 0x400>; + reg-names = "control", "domain"; + domain-id = <23>; + }; + + clktcp3d3: clktcp3d3 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "tcp3d-3"; + reg = <0x02350098 0xb00>, <0x0235005c 0x400>; + reg-names = "control", "domain"; + domain-id = <23>; + }; + + clkvcp0: clkvcp0 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "vcp-0"; + reg = <0x0235009c 0xb00>, <0x02350060 0x400>; + reg-names = "control", "domain"; + domain-id = <24>; + }; + + clkvcp1: clkvcp1 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "vcp-1"; + reg = <0x023500a0 0xb00>, <0x02350060 0x400>; + reg-names = "control", "domain"; + domain-id = <24>; + }; + + clkvcp2: clkvcp2 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "vcp-2"; + reg = <0x023500a4 0xb00>, <0x02350060 0x400>; + reg-names = "control", "domain"; + domain-id = <24>; + }; + + clkvcp3: clkvcp3 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "vcp-3"; + reg = <0x023500a8 0xb00>, <0x02350060 0x400>; + reg-names = "control", "domain"; + domain-id = <24>; + }; + + clkvcp4: clkvcp4 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "vcp-4"; + reg = <0x023500ac 0xb00>, <0x02350064 0x400>; + reg-names = "control", "domain"; + domain-id = <25>; + }; + + clkvcp5: clkvcp5 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "vcp-5"; + reg = <0x023500b0 0xb00>, <0x02350064 0x400>; + reg-names = "control", "domain"; + domain-id = <25>; + }; + + clkvcp6: clkvcp6 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "vcp-6"; + reg = <0x023500b4 0xb00>, <0x02350064 0x400>; + reg-names = "control", "domain"; + domain-id = <25>; + }; + + clkvcp7: clkvcp7 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "vcp-7"; + reg = <0x023500b8 0xb00>, <0x02350064 0x400>; + reg-names = "control", "domain"; + domain-id = <25>; + }; + + clkbcp: clkbcp { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "bcp"; + reg = <0x023500bc 0xb00>, <0x02350068 0x400>; + reg-names = "control", "domain"; + domain-id = <26>; + }; + + clkdxb: clkdxb { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "dxb"; + reg = <0x023500c0 0xb00>, <0x0235006c 0x400>; + reg-names = "control", "domain"; + domain-id = <27>; + }; + + clkhyperlink1: clkhyperlink1 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk12>; + clock-output-names = "hyperlink-1"; + reg = <0x023500c4 0xb00>, <0x02350070 0x400>; + reg-names = "control", "domain"; + domain-id = <28>; + }; + + clkxge: clkxge { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "xge"; + reg = <0x023500c8 0xb00>, <0x02350074 0x400>; + reg-names = "control", "domain"; + domain-id = <29>; + }; +}; diff --git a/arch/arm/boot/dts/k2hk-evm.dts b/arch/arm/boot/dts/k2hk-evm.dts index eaefdfef65c3..c93d06f9f2a8 100644 --- a/arch/arm/boot/dts/k2hk-evm.dts +++ b/arch/arm/boot/dts/k2hk-evm.dts @@ -1,5 +1,5 @@ /* - * Copyright 2013 Texas Instruments, Inc. + * Copyright 2013-2014 Texas Instruments, Inc. * * Keystone 2 Kepler/Hawking EVM device tree * @@ -10,12 +10,14 @@ /dts-v1/; #include "keystone.dtsi" +#include "k2hk.dtsi" / { - compatible = "ti,keystone-evm"; + compatible = "ti,k2hk-evm","ti,keystone"; + model = "Texas Instruments Keystone 2 Kepler/Hawking EVM"; soc { - clock { + clocks { refclksys: refclksys { #clock-cells = <0>; compatible = "fixed-clock"; @@ -52,6 +54,29 @@ }; }; }; + + leds { + compatible = "gpio-leds"; + debug1_1 { + label = "keystone:green:debug1"; + gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>; /* 12 */ + }; + + debug1_2 { + label = "keystone:red:debug1"; + gpios = <&gpio0 13 GPIO_ACTIVE_HIGH>; /* 13 */ + }; + + debug2 { + label = "keystone:blue:debug2"; + gpios = <&gpio0 14 GPIO_ACTIVE_HIGH>; /* 14 */ + }; + + debug3 { + label = "keystone:blue:debug3"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH>; /* 15 */ + }; + }; }; &usb_phy { @@ -61,3 +86,55 @@ &usb { status = "okay"; }; + +&aemif { + cs0 { + #address-cells = <2>; + #size-cells = <1>; + clock-ranges; + ranges; + + ti,cs-chipselect = <0>; + /* all timings in nanoseconds */ + ti,cs-min-turnaround-ns = <12>; + ti,cs-read-hold-ns = <6>; + ti,cs-read-strobe-ns = <23>; + ti,cs-read-setup-ns = <9>; + ti,cs-write-hold-ns = <8>; + ti,cs-write-strobe-ns = <23>; + ti,cs-write-setup-ns = <8>; + + nand@0,0 { + compatible = "ti,keystone-nand","ti,davinci-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0 0 0x4000000 + 1 0 0x0000100>; + + ti,davinci-chipselect = <0>; + ti,davinci-mask-ale = <0x2000>; + ti,davinci-mask-cle = <0x4000>; + ti,davinci-mask-chipsel = <0>; + nand-ecc-mode = "hw"; + ti,davinci-ecc-bits = <4>; + nand-on-flash-bbt; + + partition@0 { + label = "u-boot"; + reg = <0x0 0x100000>; + read-only; + }; + + partition@100000 { + label = "params"; + reg = <0x100000 0x80000>; + read-only; + }; + + partition@180000 { + label = "ubifs"; + reg = <0x180000 0x1fe80000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/k2hk.dtsi b/arch/arm/boot/dts/k2hk.dtsi new file mode 100644 index 000000000000..c73899c73118 --- /dev/null +++ b/arch/arm/boot/dts/k2hk.dtsi @@ -0,0 +1,46 @@ +/* + * Copyright 2013-2014 Texas Instruments, Inc. + * + * Keystone 2 Kepler/Hawking soc specific device tree + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&gic>; + + cpu@0 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <0>; + }; + + cpu@1 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <1>; + }; + + cpu@2 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <2>; + }; + + cpu@3 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <3>; + }; + }; + + soc { + /include/ "k2hk-clocks.dtsi" + }; +}; diff --git a/arch/arm/boot/dts/k2l-clocks.dtsi b/arch/arm/boot/dts/k2l-clocks.dtsi new file mode 100644 index 000000000000..f584b80200f8 --- /dev/null +++ b/arch/arm/boot/dts/k2l-clocks.dtsi @@ -0,0 +1,267 @@ +/* + * Copyright 2013-2014 Texas Instruments, Inc. + * + * Keystone 2 lamarr SoC clock nodes + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +clocks { + armpllclk: armpllclk@2620370 { + #clock-cells = <0>; + compatible = "ti,keystone,pll-clock"; + clocks = <&refclksys>; + clock-output-names = "arm-pll-clk"; + reg = <0x02620370 4>; + reg-names = "control"; + }; + + mainpllclk: mainpllclk@2310110 { + #clock-cells = <0>; + compatible = "ti,keystone,main-pll-clock"; + clocks = <&refclksys>; + reg = <0x02620350 4>, <0x02310110 4>; + reg-names = "control", "multiplier"; + fixed-postdiv = <2>; + }; + + papllclk: papllclk@2620358 { + #clock-cells = <0>; + compatible = "ti,keystone,pll-clock"; + clocks = <&refclksys>; + clock-output-names = "pa-pll-clk"; + reg = <0x02620358 4>; + reg-names = "control"; + }; + + ddr3apllclk: ddr3apllclk@2620360 { + #clock-cells = <0>; + compatible = "ti,keystone,pll-clock"; + clocks = <&refclksys>; + clock-output-names = "ddr-3a-pll-clk"; + reg = <0x02620360 4>; + reg-names = "control"; + }; + + clkdfeiqnsys: clkdfeiqnsys { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk12>; + clock-output-names = "dfe"; + reg-names = "control", "domain"; + reg = <0x02350004 0xb00>, <0x02350000 0x400>; + domain-id = <0>; + }; + + clkpcie1: clkpcie1 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk12>; + clock-output-names = "pcie"; + reg = <0x0235002c 0xb00>, <0x02350000 0x400>; + reg-names = "control", "domain"; + domain-id = <4>; + }; + + clkgem1: clkgem1 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk1>; + clock-output-names = "gem1"; + reg = <0x02350040 0xb00>, <0x02350024 0x400>; + reg-names = "control", "domain"; + domain-id = <9>; + }; + + clkgem2: clkgem2 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk1>; + clock-output-names = "gem2"; + reg = <0x02350044 0xb00>, <0x02350028 0x400>; + reg-names = "control", "domain"; + domain-id = <10>; + }; + + clkgem3: clkgem3 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk1>; + clock-output-names = "gem3"; + reg = <0x02350048 0xb00>, <0x0235002c 0x400>; + reg-names = "control", "domain"; + domain-id = <11>; + }; + + clktac: clktac { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "tac"; + reg = <0x02350064 0xb00>, <0x02350044 0x400>; + reg-names = "control", "domain"; + domain-id = <17>; + }; + + clkrac: clkrac { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "rac"; + reg = <0x02350068 0xb00>, <0x02350044 0x400>; + reg-names = "control", "domain"; + domain-id = <17>; + }; + + clkdfepd0: clkdfepd0 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "dfe-pd0"; + reg = <0x0235006c 0xb00>, <0x02350044 0x400>; + reg-names = "control", "domain"; + domain-id = <18>; + }; + + clkfftc0: clkfftc0 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "fftc-0"; + reg = <0x02350070 0xb00>, <0x0235004c 0x400>; + reg-names = "control", "domain"; + domain-id = <19>; + }; + + clkosr: clkosr { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "osr"; + reg = <0x02350088 0xb00>, <0x0235004c 0x400>; + reg-names = "control", "domain"; + domain-id = <21>; + }; + + clktcp3d0: clktcp3d0 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "tcp3d-0"; + reg = <0x0235008c 0xb00>, <0x02350058 0x400>; + reg-names = "control", "domain"; + domain-id = <22>; + }; + + clktcp3d1: clktcp3d1 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "tcp3d-1"; + reg = <0x02350094 0xb00>, <0x02350058 0x400>; + reg-names = "control", "domain"; + domain-id = <23>; + }; + + clkvcp0: clkvcp0 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "vcp-0"; + reg = <0x0235009c 0xb00>, <0x02350060 0x400>; + reg-names = "control", "domain"; + domain-id = <24>; + }; + + clkvcp1: clkvcp1 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "vcp-1"; + reg = <0x023500a0 0xb00>, <0x02350060 0x400>; + reg-names = "control", "domain"; + domain-id = <24>; + }; + + clkvcp2: clkvcp2 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "vcp-2"; + reg = <0x023500a4 0xb00>, <0x02350060 0x400>; + reg-names = "control", "domain"; + domain-id = <24>; + }; + + clkvcp3: clkvcp3 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "vcp-3"; + reg = <0x023500a8 0xb00>, <0x02350060 0x400>; + reg-names = "control", "domain"; + domain-id = <24>; + }; + + clkbcp: clkbcp { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "bcp"; + reg = <0x023500bc 0xb00>, <0x02350068 0x400>; + reg-names = "control", "domain"; + domain-id = <26>; + }; + + clkdfepd1: clkdfepd1 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "dfe-pd1"; + reg = <0x023500c0 0xb00>, <0x02350044 0x400>; + reg-names = "control", "domain"; + domain-id = <27>; + }; + + clkfftc1: clkfftc1 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "fftc-1"; + reg = <0x023500c4 0xb00>, <0x023504c0 0x400>; + reg-names = "control", "domain"; + domain-id = <28>; + }; + + clkiqnail: clkiqnail { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&chipclk13>; + clock-output-names = "iqn-ail"; + reg = <0x023500c8 0xb00>, <0x0235004c 0x400>; + reg-names = "control", "domain"; + domain-id = <29>; + }; + + clkuart2: clkuart2 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&clkmodrst0>; + clock-output-names = "uart2"; + reg = <0x02350000 0xb00>, <0x02350000 0x400>; + reg-names = "control", "domain"; + domain-id = <0>; + }; + + clkuart3: clkuart3 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&clkmodrst0>; + clock-output-names = "uart3"; + reg = <0x02350000 0xb00>, <0x02350000 0x400>; + reg-names = "control", "domain"; + domain-id = <0>; + }; +}; diff --git a/arch/arm/boot/dts/k2l-evm.dts b/arch/arm/boot/dts/k2l-evm.dts new file mode 100644 index 000000000000..50a70132ac9e --- /dev/null +++ b/arch/arm/boot/dts/k2l-evm.dts @@ -0,0 +1,37 @@ +/* + * Copyright 2014 Texas Instruments, Inc. + * + * Keystone 2 Lamarr EVM device tree + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "keystone.dtsi" +#include "k2l.dtsi" + +/ { + compatible = "ti,k2l-evm","ti,keystone"; + model = "Texas Instruments Keystone 2 Lamarr EVM"; + + soc { + clocks { + refclksys: refclksys { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <122880000>; + clock-output-names = "refclk-sys"; + }; + }; + }; +}; + +&usb_phy { + status = "okay"; +}; + +&usb { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/k2l.dtsi b/arch/arm/boot/dts/k2l.dtsi new file mode 100644 index 000000000000..1f7f479589e1 --- /dev/null +++ b/arch/arm/boot/dts/k2l.dtsi @@ -0,0 +1,55 @@ +/* + * Copyright 2014 Texas Instruments, Inc. + * + * Keystone 2 Lamarr SoC specific device tree + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/ { + cpus { + #address-cells = <1>; + #size-cells = <0>; + + interrupt-parent = <&gic>; + + cpu@0 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <0>; + }; + + cpu@1 { + compatible = "arm,cortex-a15"; + device_type = "cpu"; + reg = <1>; + }; + }; + + soc { + + /include/ "k2l-clocks.dtsi" + + uart2: serial@02348400 { + compatible = "ns16550a"; + current-speed = <115200>; + reg-shift = <2>; + reg-io-width = <4>; + reg = <0x02348400 0x100>; + clocks = <&clkuart2>; + interrupts = <GIC_SPI 432 IRQ_TYPE_EDGE_RISING>; + }; + + uart3: serial@02348800 { + compatible = "ns16550a"; + current-speed = <115200>; + reg-shift = <2>; + reg-io-width = <4>; + reg = <0x02348800 0x100>; + clocks = <&clkuart3>; + interrupts = <GIC_SPI 435 IRQ_TYPE_EDGE_RISING>; + }; + }; +}; diff --git a/arch/arm/boot/dts/keystone-clocks.dtsi b/arch/arm/boot/dts/keystone-clocks.dtsi index ef58d1c24313..93f82c7010ab 100644 --- a/arch/arm/boot/dts/keystone-clocks.dtsi +++ b/arch/arm/boot/dts/keystone-clocks.dtsi @@ -13,51 +13,6 @@ clocks { #size-cells = <1>; ranges; - mainpllclk: mainpllclk@2310110 { - #clock-cells = <0>; - compatible = "ti,keystone,main-pll-clock"; - clocks = <&refclksys>; - reg = <0x02620350 4>, <0x02310110 4>; - reg-names = "control", "multiplier"; - fixed-postdiv = <2>; - }; - - papllclk: papllclk@2620358 { - #clock-cells = <0>; - compatible = "ti,keystone,pll-clock"; - clocks = <&refclkpass>; - clock-output-names = "pa-pll-clk"; - reg = <0x02620358 4>; - reg-names = "control"; - }; - - ddr3apllclk: ddr3apllclk@2620360 { - #clock-cells = <0>; - compatible = "ti,keystone,pll-clock"; - clocks = <&refclkddr3a>; - clock-output-names = "ddr-3a-pll-clk"; - reg = <0x02620360 4>; - reg-names = "control"; - }; - - ddr3bpllclk: ddr3bpllclk@2620368 { - #clock-cells = <0>; - compatible = "ti,keystone,pll-clock"; - clocks = <&refclkddr3b>; - clock-output-names = "ddr-3b-pll-clk"; - reg = <0x02620368 4>; - reg-names = "control"; - }; - - armpllclk: armpllclk@2620370 { - #clock-cells = <0>; - compatible = "ti,keystone,pll-clock"; - clocks = <&refclkarm>; - clock-output-names = "arm-pll-clk"; - reg = <0x02620370 4>; - reg-names = "control"; - }; - mainmuxclk: mainmuxclk@2310108 { #clock-cells = <0>; compatible = "ti,keystone,pll-mux-clock"; @@ -244,7 +199,7 @@ clocks { clock-output-names = "debugss-trc"; reg = <0x02350014 0xb00>, <0x02350000 0x400>; reg-names = "control", "domain"; - domain-id = <0>; + domain-id = <1>; }; clktetbtrc: clktetbtrc { @@ -297,26 +252,6 @@ clocks { domain-id = <3>; }; - clksrio: clksrio { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk1rstiso13>; - clock-output-names = "srio"; - reg = <0x0235002c 0xb00>, <0x02350010 0x400>; - reg-names = "control", "domain"; - domain-id = <4>; - }; - - clkhyperlink0: clkhyperlink0 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk12>; - clock-output-names = "hyperlink-0"; - reg = <0x02350030 0xb00>, <0x02350014 0x400>; - reg-names = "control", "domain"; - domain-id = <5>; - }; - clksr: clksr { #clock-cells = <0>; compatible = "ti,keystone,psc-clock"; @@ -327,16 +262,6 @@ clocks { domain-id = <6>; }; - clkmsmcsram: clkmsmcsram { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk1>; - clock-output-names = "msmcsram"; - reg = <0x02350038 0xb00>, <0x0235001c 0x400>; - reg-names = "control", "domain"; - domain-id = <7>; - }; - clkgem0: clkgem0 { #clock-cells = <0>; compatible = "ti,keystone,psc-clock"; @@ -347,76 +272,6 @@ clocks { domain-id = <8>; }; - clkgem1: clkgem1 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk1>; - clock-output-names = "gem1"; - reg = <0x02350040 0xb00>, <0x02350024 0x400>; - reg-names = "control", "domain"; - domain-id = <9>; - }; - - clkgem2: clkgem2 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk1>; - clock-output-names = "gem2"; - reg = <0x02350044 0xb00>, <0x02350028 0x400>; - reg-names = "control", "domain"; - domain-id = <10>; - }; - - clkgem3: clkgem3 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk1>; - clock-output-names = "gem3"; - reg = <0x02350048 0xb00>, <0x0235002c 0x400>; - reg-names = "control", "domain"; - domain-id = <11>; - }; - - clkgem4: clkgem4 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk1>; - clock-output-names = "gem4"; - reg = <0x0235004c 0xb00>, <0x02350030 0x400>; - reg-names = "control", "domain"; - domain-id = <12>; - }; - - clkgem5: clkgem5 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk1>; - clock-output-names = "gem5"; - reg = <0x02350050 0xb00>, <0x02350034 0x400>; - reg-names = "control", "domain"; - domain-id = <13>; - }; - - clkgem6: clkgem6 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk1>; - clock-output-names = "gem6"; - reg = <0x02350054 0xb00>, <0x02350038 0x400>; - reg-names = "control", "domain"; - domain-id = <14>; - }; - - clkgem7: clkgem7 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk1>; - clock-output-names = "gem7"; - reg = <0x02350058 0xb00>, <0x0235003c 0x400>; - reg-names = "control", "domain"; - domain-id = <15>; - }; - clkddr30: clkddr30 { #clock-cells = <0>; compatible = "ti,keystone,psc-clock"; @@ -427,276 +282,6 @@ clocks { domain-id = <16>; }; - clkddr31: clkddr31 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "ddr3-1"; - reg = <0x02350060 0xb00>, <0x02350040 0x400>; - reg-names = "control", "domain"; - domain-id = <16>; - }; - - clktac: clktac { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "tac"; - reg = <0x02350064 0xb00>, <0x02350044 0x400>; - reg-names = "control", "domain"; - domain-id = <17>; - }; - - clkrac01: clktac01 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "rac-01"; - reg = <0x02350068 0xb00>, <0x02350044 0x400>; - reg-names = "control", "domain"; - domain-id = <17>; - }; - - clkrac23: clktac23 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "rac-23"; - reg = <0x0235006c 0xb00>, <0x02350048 0x400>; - reg-names = "control", "domain"; - domain-id = <18>; - }; - - clkfftc0: clkfftc0 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "fftc-0"; - reg = <0x02350070 0xb00>, <0x0235004c 0x400>; - reg-names = "control", "domain"; - domain-id = <19>; - }; - - clkfftc1: clkfftc1 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "fftc-1"; - reg = <0x02350074 0xb00>, <0x023504c0 0x400>; - reg-names = "control", "domain"; - domain-id = <19>; - }; - - clkfftc2: clkfftc2 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "fftc-2"; - reg = <0x02350078 0xb00>, <0x02350050 0x400>; - reg-names = "control", "domain"; - domain-id = <20>; - }; - - clkfftc3: clkfftc3 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "fftc-3"; - reg = <0x0235007c 0xb00>, <0x02350050 0x400>; - reg-names = "control", "domain"; - domain-id = <20>; - }; - - clkfftc4: clkfftc4 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "fftc-4"; - reg = <0x02350080 0xb00>, <0x02350050 0x400>; - reg-names = "control", "domain"; - domain-id = <20>; - }; - - clkfftc5: clkfftc5 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "fftc-5"; - reg = <0x02350084 0xb00>, <0x02350050 0x400>; - reg-names = "control", "domain"; - domain-id = <20>; - }; - - clkaif: clkaif { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "aif"; - reg = <0x02350088 0xb00>, <0x02350054 0x400>; - reg-names = "control", "domain"; - domain-id = <21>; - }; - - clktcp3d0: clktcp3d0 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "tcp3d-0"; - reg = <0x0235008c 0xb00>, <0x02350058 0x400>; - reg-names = "control", "domain"; - domain-id = <22>; - }; - - clktcp3d1: clktcp3d1 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "tcp3d-1"; - reg = <0x02350090 0xb00>, <0x02350058 0x400>; - reg-names = "control", "domain"; - domain-id = <22>; - }; - - clktcp3d2: clktcp3d2 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "tcp3d-2"; - reg = <0x02350094 0xb00>, <0x0235005c 0x400>; - reg-names = "control", "domain"; - domain-id = <23>; - }; - - clktcp3d3: clktcp3d3 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "tcp3d-3"; - reg = <0x02350098 0xb00>, <0x0235005c 0x400>; - reg-names = "control", "domain"; - domain-id = <23>; - }; - - clkvcp0: clkvcp0 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "vcp-0"; - reg = <0x0235009c 0xb00>, <0x02350060 0x400>; - reg-names = "control", "domain"; - domain-id = <24>; - }; - - clkvcp1: clkvcp1 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "vcp-1"; - reg = <0x023500a0 0xb00>, <0x02350060 0x400>; - reg-names = "control", "domain"; - domain-id = <24>; - }; - - clkvcp2: clkvcp2 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "vcp-2"; - reg = <0x023500a4 0xb00>, <0x02350060 0x400>; - reg-names = "control", "domain"; - domain-id = <24>; - }; - - clkvcp3: clkvcp3 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "vcp-3"; - reg = <0x023500a8 0xb00>, <0x02350060 0x400>; - reg-names = "control", "domain"; - domain-id = <24>; - }; - - clkvcp4: clkvcp4 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "vcp-4"; - reg = <0x023500ac 0xb00>, <0x02350064 0x400>; - reg-names = "control", "domain"; - domain-id = <25>; - }; - - clkvcp5: clkvcp5 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "vcp-5"; - reg = <0x023500b0 0xb00>, <0x02350064 0x400>; - reg-names = "control", "domain"; - domain-id = <25>; - }; - - clkvcp6: clkvcp6 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "vcp-6"; - reg = <0x023500b4 0xb00>, <0x02350064 0x400>; - reg-names = "control", "domain"; - domain-id = <25>; - }; - - clkvcp7: clkvcp7 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "vcp-7"; - reg = <0x023500b8 0xb00>, <0x02350064 0x400>; - reg-names = "control", "domain"; - domain-id = <25>; - }; - - clkbcp: clkbcp { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "bcp"; - reg = <0x023500bc 0xb00>, <0x02350068 0x400>; - reg-names = "control", "domain"; - domain-id = <26>; - }; - - clkdxb: clkdxb { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "dxb"; - reg = <0x023500c0 0xb00>, <0x0235006c 0x400>; - reg-names = "control", "domain"; - domain-id = <27>; - }; - - clkhyperlink1: clkhyperlink1 { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk12>; - clock-output-names = "hyperlink-1"; - reg = <0x023500c4 0xb00>, <0x02350070 0x400>; - reg-names = "control", "domain"; - domain-id = <28>; - }; - - clkxge: clkxge { - #clock-cells = <0>; - compatible = "ti,keystone,psc-clock"; - clocks = <&chipclk13>; - clock-output-names = "xge"; - reg = <0x023500c8 0xb00>, <0x02350074 0x400>; - reg-names = "control", "domain"; - domain-id = <29>; - }; - clkwdtimer0: clkwdtimer0 { #clock-cells = <0>; compatible = "ti,keystone,psc-clock"; @@ -737,6 +322,16 @@ clocks { domain-id = <0>; }; + clktimer15: clktimer15 { + #clock-cells = <0>; + compatible = "ti,keystone,psc-clock"; + clocks = <&clkmodrst0>; + clock-output-names = "timer15"; + reg = <0x02350000 0xb00>, <0x02350000 0x400>; + reg-names = "control", "domain"; + domain-id = <0>; + }; + clkuart0: clkuart0 { #clock-cells = <0>; compatible = "ti,keystone,psc-clock"; diff --git a/arch/arm/boot/dts/keystone.dtsi b/arch/arm/boot/dts/keystone.dtsi index b4202907a27b..90823eb90c1b 100644 --- a/arch/arm/boot/dts/keystone.dtsi +++ b/arch/arm/boot/dts/keystone.dtsi @@ -7,6 +7,7 @@ */ #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/gpio/gpio.h> #include "skeleton.dtsi" @@ -24,37 +25,6 @@ reg = <0x00000000 0x80000000 0x00000000 0x40000000>; }; - cpus { - #address-cells = <1>; - #size-cells = <0>; - - interrupt-parent = <&gic>; - - cpu@0 { - compatible = "arm,cortex-a15"; - device_type = "cpu"; - reg = <0>; - }; - - cpu@1 { - compatible = "arm,cortex-a15"; - device_type = "cpu"; - reg = <1>; - }; - - cpu@2 { - compatible = "arm,cortex-a15"; - device_type = "cpu"; - reg = <2>; - }; - - cpu@3 { - compatible = "arm,cortex-a15"; - device_type = "cpu"; - reg = <3>; - }; - }; - gic: interrupt-controller { compatible = "arm,cortex-a15-gic"; #interrupt-cells = <3>; @@ -208,5 +178,75 @@ usb-phy = <&usb_phy>, <&usb_phy>; }; }; + + wdt: wdt@022f0080 { + compatible = "ti,keystone-wdt","ti,davinci-wdt"; + reg = <0x022f0080 0x80>; + clocks = <&clkwdtimer0>; + }; + + clock_event: timer@22f0000 { + compatible = "ti,keystone-timer"; + reg = <0x022f0000 0x80>; + interrupts = <GIC_SPI 110 IRQ_TYPE_EDGE_RISING>; + clocks = <&clktimer15>; + }; + + gpio0: gpio@260bf00 { + compatible = "ti,keystone-gpio"; + reg = <0x0260bf00 0x100>; + gpio-controller; + #gpio-cells = <2>; + /* HW Interrupts mapped to GPIO pins */ + interrupts = <GIC_SPI 120 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 121 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 122 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 123 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 124 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 125 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 126 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 127 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 128 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 129 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 130 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 131 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 132 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 133 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 134 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 135 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 136 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 137 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 138 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 139 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 140 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 141 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 142 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 143 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 144 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 145 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 146 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 147 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 148 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 149 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 150 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 151 IRQ_TYPE_EDGE_RISING>; + clocks = <&clkgpio>; + clock-names = "gpio"; + ti,ngpio = <32>; + ti,davinci-gpio-unbanked = <32>; + }; + + aemif: aemif@21000A00 { + compatible = "ti,keystone-aemif", "ti,davinci-aemif"; + #address-cells = <2>; + #size-cells = <1>; + clocks = <&clkaemif>; + clock-names = "aemif"; + clock-ranges; + + reg = <0x21000A00 0x00000100>; + ranges = <0 0 0x30000000 0x10000000 + 1 0 0x21000A00 0x00000100>; + }; }; }; diff --git a/arch/arm/boot/dts/kirkwood-b3.dts b/arch/arm/boot/dts/kirkwood-b3.dts new file mode 100644 index 000000000000..40791053106b --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-b3.dts @@ -0,0 +1,204 @@ +/* + * Device Tree file for Excito Bubba B3 + * + * Copyright (C) 2013, Andrew Lunn <andrew@lunn.ch> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + * + * Note: This requires a new'ish version of u-boot, which disables the + * L2 cache. If your B3 silently fails to boot, u-boot is probably too + * old. Either upgrade, or consider the following email: + * + * http://lists.debian.org/debian-arm/2012/08/msg00128.html + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" + +/ { + model = "Excito B3"; + compatible = "excito,b3", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + memory { /* 512 MB */ + device_type = "memory"; + reg = <0x00000000 0x20000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8 earlyprintk"; + }; + + mbus { + pcie-controller { + status = "okay"; + + /* Wifi model has Atheros chipset on pcie port */ + pcie@1,0 { + status = "okay"; + }; + }; + }; + + ocp@f1000000 { + pinctrl: pinctrl@10000 { + pmx_button_power: pmx-button-power { + marvell,pins = "mpp39"; + marvell,function = "gpio"; + }; + pmx_led_green: pmx-led-green { + marvell,pins = "mpp38"; + marvell,function = "gpio"; + }; + pmx_led_red: pmx-led-red { + marvell,pins = "mpp41"; + marvell,function = "gpio"; + }; + pmx_led_blue: pmx-led-blue { + marvell,pins = "mpp42"; + marvell,function = "gpio"; + }; + pmx_beeper: pmx-beeper { + marvell,pins = "mpp40"; + marvell,function = "gpio"; + }; + }; + + spi@10600 { + status = "okay"; + pinctrl-0 = <&pmx_spi>; + pinctrl-names = "default"; + + m25p16@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "m25p16"; + reg = <0>; + spi-max-frequency = <40000000>; + mode = <0>; + + partition@0 { + reg = <0x0 0xc0000>; + label = "u-boot"; + }; + + partition@c0000 { + reg = <0xc0000 0x20000>; + label = "u-boot env"; + }; + + partition@e0000 { + reg = <0xe0000 0x120000>; + label = "data"; + }; + }; + }; + + i2c@11000 { + status = "okay"; + /* + * There is something on the bus at address 0x64. + * Not yet identified what it is, maybe the eeprom + * for the Atheros WiFi chip? + */ + }; + + + serial@12000 { + /* Internal on test pins, 3.3v TTL + * UART0_RX = Testpoint 65 + * UART0_TX = Testpoint 66 + * See the Excito Wiki for more details. + */ + pinctrl-0 = <&pmx_uart0>; + pinctrl-names = "default"; + status = "okay"; + }; + + sata@80000 { + /* One internal, the second as eSATA */ + status = "okay"; + nr-ports = <2>; + }; + }; + + gpio-leds { + /* + * There is one LED "port" on the front and the colours + * mix together giving some interesting combinations. + */ + compatible = "gpio-leds"; + pinctrl-0 = < &pmx_led_green &pmx_led_red + &pmx_led_blue >; + pinctrl-names = "default"; + + programming_led { + label = "bubba3:green:programming"; + gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + error_led { + label = "bubba3:red:error"; + gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + }; + + active_led { + label = "bubba3:blue:active"; + gpios = <&gpio1 10 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + pinctrl-0 = <&pmx_button_power>; + pinctrl-names = "default"; + + power-button { + /* On the back */ + label = "Power Button"; + linux,code = <KEY_POWER>; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + }; + }; + + beeper: beeper { + /* 4KHz Piezoelectric buzzer */ + compatible = "gpio-beeper"; + pinctrl-0 = <&pmx_beeper>; + pinctrl-names = "default"; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@8 { + device_type = "ethernet-phy"; + reg = <8>; + }; + + ethphy1: ethernet-phy@24 { + device_type = "ethernet-phy"; + reg = <24>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; + +ð1 { + status = "okay"; + ethernet1-port@0 { + phy-handle = <ðphy1>; + }; +}; + diff --git a/arch/arm/boot/dts/kirkwood-ds109.dts b/arch/arm/boot/dts/kirkwood-ds109.dts new file mode 100644 index 000000000000..772092c94ca3 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds109.dts @@ -0,0 +1,41 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS109, DS110, DS110jv20"; + compatible = "synology,ds109", "synology,ds110jv20", + "synology,ds110", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-1 { + status = "okay"; + }; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds110jv10.dts b/arch/arm/boot/dts/kirkwood-ds110jv10.dts new file mode 100644 index 000000000000..aabafbe0da4c --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds110jv10.dts @@ -0,0 +1,41 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS110j v10 and v30"; + compatible = "synology,ds110jv10", "synology,ds110jv30", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-1 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds111.dts b/arch/arm/boot/dts/kirkwood-ds111.dts new file mode 100644 index 000000000000..16ec7fbab573 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds111.dts @@ -0,0 +1,44 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS111"; + compatible = "synology,ds111", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-hdd-21-1 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds112.dts b/arch/arm/boot/dts/kirkwood-ds112.dts new file mode 100644 index 000000000000..cff1b2388765 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds112.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS111"; + compatible = "synology,ds111", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-21-2 { + status = "okay"; + }; + + regulators-hdd-30 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds209.dts b/arch/arm/boot/dts/kirkwood-ds209.dts new file mode 100644 index 000000000000..330411993d38 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds209.dts @@ -0,0 +1,44 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS209"; + compatible = "synology,ds209", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-2 { + status = "okay"; + }; + + regulators-hdd-31 { + status = "okay"; + }; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds210.dts b/arch/arm/boot/dts/kirkwood-ds210.dts new file mode 100644 index 000000000000..6052eaa37d4f --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds210.dts @@ -0,0 +1,46 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS210 v10, v20, v30, DS211j"; + compatible = "synology,ds210jv10", "synology,ds210jv20", + "synology,ds210jv30", "synology,ds211j", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-2 { + status = "okay"; + }; + + regulators-hdd-31 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds212.dts b/arch/arm/boot/dts/kirkwood-ds212.dts new file mode 100644 index 000000000000..7f76cd30e84e --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds212.dts @@ -0,0 +1,47 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS212, DS212p v10, v20, DS213air v10, DS213 v10"; + compatible = "synology,ds212", "synology,ds212pv10", + "synology,ds212pv10", "synology,ds212pv20", + "synology,ds213airv10", "synology,ds213v10", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-hdd-21-2 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds212j.dts b/arch/arm/boot/dts/kirkwood-ds212j.dts new file mode 100644 index 000000000000..1f83a00f1f74 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds212j.dts @@ -0,0 +1,41 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS212j v10, v20"; + compatible = "synology,ds212jv10", "synology,ds212jv20", + "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-21-2 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds409.dts b/arch/arm/boot/dts/kirkwood-ds409.dts new file mode 100644 index 000000000000..0a573add44a2 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds409.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS409, DS410j"; + compatible = "synology,ds409", "synology,ds410j", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-15-18 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; + + gpio-leds-alarm-12 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds409slim.dts b/arch/arm/boot/dts/kirkwood-ds409slim.dts new file mode 100644 index 000000000000..1848a6245fd3 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds409slim.dts @@ -0,0 +1,40 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology 409slim"; + compatible = "synology,ds409slim", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-32-35 { + status = "okay"; + }; + + gpio-leds-hdd-20 { + status = "okay"; + }; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds411.dts b/arch/arm/boot/dts/kirkwood-ds411.dts new file mode 100644 index 000000000000..a1737b4311c6 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds411.dts @@ -0,0 +1,52 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS411, DS413jv10"; + compatible = "synology,ds411", "synology,ds413jv10", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; + + regulators-hdd-34 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds411j.dts b/arch/arm/boot/dts/kirkwood-ds411j.dts new file mode 100644 index 000000000000..0cde914eceae --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds411j.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS411j"; + compatible = "synology,ds411j", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-15-18 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; + + gpio-leds-alarm-12 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-ds411slim.dts b/arch/arm/boot/dts/kirkwood-ds411slim.dts new file mode 100644 index 000000000000..aef0cadc2c78 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ds411slim.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology DS411slim"; + compatible = "synology,ds411slim", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-1 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-rd88f6192.dts b/arch/arm/boot/dts/kirkwood-rd88f6192.dts new file mode 100644 index 000000000000..e9dd85049297 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-rd88f6192.dts @@ -0,0 +1,112 @@ +/* + * Marvell RD88F6192 Board descrition + * + * Andrew Lunn <andrew@lunn.ch> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + * + * This file contains the definitions that are common between the three + * variants of the Marvell Kirkwood Development Board. + */ +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6192.dtsi" + +/ { + model = "Marvell RD88F6192 reference design"; + compatible = "marvell,rd88f6192", "marvell,kirkwood-88f6192", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + mbus { + pcie-controller { + status = "okay"; + + pcie@1,0 { + status = "okay"; + }; + }; + }; + + ocp@f1000000 { + pinctrl: pinctrl@10000 { + pinctrl-0 = <&pmx_usb_power>; + pinctrl-names = "default"; + + pmx_usb_power: pmx-usb-power { + marvell,pins = "mpp10"; + marvell,function = "gpo"; + }; + }; + + serial@12000 { + status = "okay"; + + }; + + spi@10600 { + status = "okay"; + pinctrl-0 = <&pmx_spi>; + pinctrl-names = "default"; + + m25p128@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p128"; + reg = <0>; + spi-max-frequency = <20000000>; + mode = <0>; + }; + }; + + sata@80000 { + status = "okay"; + nr-ports = <2>; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_usb_power>; + pinctrl-names = "default"; + + usb_power: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "USB VBUS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio0 10 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@8 { + reg = <8>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; \ No newline at end of file diff --git a/arch/arm/boot/dts/kirkwood-rd88f6281-a0.dts b/arch/arm/boot/dts/kirkwood-rd88f6281-a0.dts new file mode 100644 index 000000000000..a803bbb70bc8 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-rd88f6281-a0.dts @@ -0,0 +1,26 @@ +/* + * Marvell RD88F6181 A0 Board descrition + * + * Andrew Lunn <andrew@lunn.ch> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + * + * This file contains the definitions for the board with the A0 variant of + * the SoC. The ethernet switch does not have a "wan" port. + */ + +/dts-v1/; +#include "kirkwood-rd88f6281.dtsi" + +/ { + model = "Marvell RD88f6281 Reference design, with A0 SoC"; + compatible = "marvell,rd88f6281-a0", "marvell,rd88f6281","marvell,kirkwood-88f6281", "marvell,kirkwood"; + + dsa@0 { + switch@0 { + reg = <10 0>; /* MDIO address 10, switch 0 in tree */ + }; + }; +}; \ No newline at end of file diff --git a/arch/arm/boot/dts/kirkwood-rd88f6281-a1.dts b/arch/arm/boot/dts/kirkwood-rd88f6281-a1.dts new file mode 100644 index 000000000000..baeebbf1d8c7 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-rd88f6281-a1.dts @@ -0,0 +1,31 @@ +/* + * Marvell RD88F6181 A1 Board descrition + * + * Andrew Lunn <andrew@lunn.ch> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + * + * This file contains the definitions for the board with the A1 variant of + * the SoC. The ethernet switch has a "wan" port. + */ + +/dts-v1/; + +#include "kirkwood-rd88f6281.dtsi" + +/ { + model = "Marvell RD88f6281 Reference design, with A1 SoC"; + compatible = "marvell,rd88f6281-a1", "marvell,rd88f6281","marvell,kirkwood-88f6281", "marvell,kirkwood"; + + dsa@0 { + switch@0 { + reg = <0 0>; /* MDIO address 0, switch 0 in tree */ + port@4 { + reg = <4>; + label = "wan"; + }; + }; + }; +}; \ No newline at end of file diff --git a/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi b/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi new file mode 100644 index 000000000000..d6368c39102e --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-rd88f6281.dtsi @@ -0,0 +1,152 @@ +/* + * Marvell RD88F6181 Common Board descrition + * + * Andrew Lunn <andrew@lunn.ch> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + * + * This file contains the definitions that are common between the two + * variants of the Marvell Kirkwood Development Board. + */ + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" + +/ { + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + mbus { + pcie-controller { + status = "okay"; + + pcie@1,0 { + status = "okay"; + }; + }; + }; + + ocp@f1000000 { + pinctrl: pinctrl@10000 { + pinctrl-0 = <&pmx_sdio_cd>; + pinctrl-names = "default"; + + pmx_sdio_cd: pmx-sdio-cd { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + }; + + serial@12000 { + status = "okay"; + + }; + + sata@80000 { + status = "okay"; + nr-ports = <2>; + }; + mvsdio@90000 { + pinctrl-0 = <&pmx_sdio &pmx_sdio_cd>; + pinctrl-names = "default"; + status = "okay"; + cd-gpios = <&gpio0 28 GPIO_ACTIVE_HIGH>; + /* No WP GPIO */ + }; + }; + + dsa@0 { + compatible = "marvell,dsa"; + #address-cells = <2>; + #size-cells = <0>; + + dsa,ethernet = <ð0>; + dsa,mii-bus = <ðphy1>; + + switch@0 { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan1"; + }; + + port@1 { + reg = <1>; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "lan3"; + }; + + port@3 { + reg = <3>; + label = "lan4"; + }; + + port@5 { + reg = <5>; + label = "cpu"; + }; + }; + }; +}; + +&nand { + status = "okay"; + + partition@0 { + label = "u-boot"; + reg = <0x0000000 0x100000>; + read-only; + }; + + partition@100000 { + label = "uImage"; + reg = <0x0100000 0x200000>; + }; + + partition@300000 { + label = "data"; + reg = <0x0300000 0x500000>; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@0 { + reg = <0>; + }; + + ethphy1: ethernet-phy@ff { + reg = <0xff>; /* No PHY attached */ + speed = <1000>; + duple = <1>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; + +ð1 { + status = "okay"; + ethernet1-port@0 { + phy-handle = <ðphy1>; + }; +}; diff --git a/arch/arm/boot/dts/kirkwood-rs212.dts b/arch/arm/boot/dts/kirkwood-rs212.dts new file mode 100644 index 000000000000..93ec3d00c6ab --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-rs212.dts @@ -0,0 +1,48 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology RS212"; + compatible = "synology,rs212", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-3 { + status = "okay"; + }; + + gpio-leds-hdd-38 { + status = "okay"; + }; + + regulators-hdd-30-2 { + status = "okay"; + }; +}; + +&s35390a { + status = "okay"; +}; + +&pcie2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-rs409.dts b/arch/arm/boot/dts/kirkwood-rs409.dts new file mode 100644 index 000000000000..311df4e5aa28 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-rs409.dts @@ -0,0 +1,44 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology RS409"; + compatible = "synology,rs409", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-150-15-18 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&rs5c372 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-rs411.dts b/arch/arm/boot/dts/kirkwood-rs411.dts new file mode 100644 index 000000000000..f90da850bb31 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-rs411.dts @@ -0,0 +1,44 @@ +/* + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-synology.dtsi" + +/ { + model = "Synology RS411 RS812"; + compatible = "synology,rs411", "synology,rs812", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x8000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + gpio-fan-100-15-35-3 { + status = "okay"; + }; + + gpio-leds-hdd-36 { + status = "okay"; + }; +}; + +ð1 { + status = "okay"; +}; + +&s35390a { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/kirkwood-synology.dtsi b/arch/arm/boot/dts/kirkwood-synology.dtsi new file mode 100644 index 000000000000..4227c974729d --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-synology.dtsi @@ -0,0 +1,871 @@ +/* + * Nodes for Marvell 628x Synology devices + * + * Andrew Lunn <andrew@lunn.ch> + * Ben Peddell <klightspeed@killerwolves.net> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. + */ + +/ { + mbus { + pcie-controller { + status = "okay"; + + pcie@1,0 { + status = "okay"; + }; + + pcie2: pcie@2,0 { + status = "disabled"; + }; + }; + }; + + ocp@f1000000 { + pinctrl: pinctrl@10000 { + pmx_alarmled_12: pmx-alarmled-12 { + marvell,pins = "mpp12"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_15: pmx-fanctrl-15 { + marvell,pins = "mpp15"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_16: pmx-fanctrl-16 { + marvell,pins = "mpp16"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_17: pmx-fanctrl-17 { + marvell,pins = "mpp17"; + marvell,function = "gpio"; + }; + + pmx_fanalarm_18: pmx-fanalarm-18 { + marvell,pins = "mpp18"; + marvell,function = "gpo"; + }; + + pmx_hddled_20: pmx-hddled-20 { + marvell,pins = "mpp20"; + marvell,function = "gpio"; + }; + + pmx_hddled_21: pmx-hddled-21 { + marvell,pins = "mpp21"; + marvell,function = "gpio"; + }; + + pmx_hddled_22: pmx-hddled-22 { + marvell,pins = "mpp22"; + marvell,function = "gpio"; + }; + + pmx_hddled_23: pmx-hddled-23 { + marvell,pins = "mpp23"; + marvell,function = "gpio"; + }; + + pmx_hddled_24: pmx-hddled-24 { + marvell,pins = "mpp24"; + marvell,function = "gpio"; + }; + + pmx_hddled_25: pmx-hddled-25 { + marvell,pins = "mpp25"; + marvell,function = "gpio"; + }; + + pmx_hddled_26: pmx-hddled-26 { + marvell,pins = "mpp26"; + marvell,function = "gpio"; + }; + + pmx_hddled_27: pmx-hddled-27 { + marvell,pins = "mpp27"; + marvell,function = "gpio"; + }; + + pmx_hddled_28: pmx-hddled-28 { + marvell,pins = "mpp28"; + marvell,function = "gpio"; + }; + + pmx_hdd1_pwr_29: pmx-hdd1-pwr-29 { + marvell,pins = "mpp29"; + marvell,function = "gpio"; + }; + + pmx_hdd1_pwr_30: pmx-hdd-pwr-30 { + marvell,pins = "mpp30"; + marvell,function = "gpio"; + }; + + pmx_hdd2_pwr_31: pmx-hdd2-pwr-31 { + marvell,pins = "mpp31"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_32: pmx-fanctrl-32 { + marvell,pins = "mpp32"; + marvell,function = "gpio"; + }; + + pmx_fanctrl_33: pmx-fanctrl-33 { + marvell,pins = "mpp33"; + marvell,function = "gpo"; + }; + + pmx_fanctrl_34: pmx-fanctrl-34 { + marvell,pins = "mpp34"; + marvell,function = "gpio"; + }; + + pmx_hdd2_pwr_34: pmx-hdd2-pwr-34 { + marvell,pins = "mpp34"; + marvell,function = "gpio"; + }; + + pmx_fanalarm_35: pmx-fanalarm-35 { + marvell,pins = "mpp35"; + marvell,function = "gpio"; + }; + + pmx_hddled_36: pmx-hddled-36 { + marvell,pins = "mpp36"; + marvell,function = "gpio"; + }; + + pmx_hddled_37: pmx-hddled-37 { + marvell,pins = "mpp37"; + marvell,function = "gpio"; + }; + + pmx_hddled_38: pmx-hddled-38 { + marvell,pins = "mpp38"; + marvell,function = "gpio"; + }; + + pmx_hddled_39: pmx-hddled-39 { + marvell,pins = "mpp39"; + marvell,function = "gpio"; + }; + + pmx_hddled_40: pmx-hddled-40 { + marvell,pins = "mpp40"; + marvell,function = "gpio"; + }; + + pmx_hddled_41: pmx-hddled-41 { + marvell,pins = "mpp41"; + marvell,function = "gpio"; + }; + + pmx_hddled_42: pmx-hddled-42 { + marvell,pins = "mpp42"; + marvell,function = "gpio"; + }; + + pmx_hddled_43: pmx-hddled-43 { + marvell,pins = "mpp43"; + marvell,function = "gpio"; + }; + + pmx_hddled_44: pmx-hddled-44 { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_hddled_45: pmx-hddled-45 { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + pmx_hdd3_pwr_44: pmx-hdd3-pwr-44 { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_hdd4_pwr_45: pmx-hdd4-pwr-45 { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + pmx_fanalarm_44: pmx-fanalarm-44 { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + pmx_fanalarm_45: pmx-fanalarm-45 { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + }; + + rtc@10300 { + status = "disabled"; + }; + + spi@10600 { + status = "okay"; + pinctrl-0 = <&pmx_spi>; + pinctrl-names = "default"; + + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + reg = <0>; + spi-max-frequency = <20000000>; + mode = <0>; + + partition@00000000 { + reg = <0x00000000 0x00080000>; + label = "RedBoot"; + }; + + partition@00080000 { + reg = <0x00080000 0x00200000>; + label = "zImage"; + }; + + partition@00280000 { + reg = <0x00280000 0x00140000>; + label = "rd.gz"; + }; + + partition@003c0000 { + reg = <0x003c0000 0x00010000>; + label = "vendor"; + }; + + partition@003d0000 { + reg = <0x003d0000 0x00020000>; + label = "RedBoot config"; + }; + + partition@003f0000 { + reg = <0x003f0000 0x00010000>; + label = "FIS directory"; + }; + }; + }; + + i2c@11000 { + status = "okay"; + clock-frequency = <400000>; + pinctrl-0 = <&pmx_twsi0>; + pinctrl-names = "default"; + + rs5c372: rs5c372@32 { + status = "disabled"; + compatible = "ricoh,rs5c372"; + reg = <0x32>; + }; + + s35390a: s35390a@30 { + status = "disabled"; + compatible = "ssi,s35390a"; + reg = <0x30>; + }; + }; + + serial@12000 { + status = "okay"; + pinctrl-0 = <&pmx_uart0>; + pinctrl-names = "default"; + }; + + serial@12100 { + status = "okay"; + pinctrl-0 = <&pmx_uart1>; + pinctrl-names = "default"; + }; + + poweroff@12100 { + compatible = "synology,power-off"; + reg = <0x12100 0x100>; + clocks = <&gate_clk 7>; + }; + + sata@80000 { + pinctrl-0 = <&pmx_sata0 &pmx_sata1>; + pinctrl-names = "default"; + status = "okay"; + nr-ports = <2>; + }; + }; + + gpio-fan-150-32-35 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34 + &pmx_fanalarm_35>; + pinctrl-names = "default"; + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH + &gpio1 1 GPIO_ACTIVE_HIGH + &gpio1 2 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2200 1 + 2500 2 + 3000 4 + 3300 3 + 3700 5 + 3800 6 + 4200 7 >; + }; + + gpio-fan-150-15-18 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 + &pmx_fanalarm_18>; + pinctrl-names = "default"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH + &gpio0 16 GPIO_ACTIVE_HIGH + &gpio0 17 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2200 1 + 2500 2 + 3000 4 + 3300 3 + 3700 5 + 3800 6 + 4200 7 >; + }; + + gpio-fan-100-32-35 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_32 &pmx_fanctrl_33 &pmx_fanctrl_34 + &pmx_fanalarm_35>; + pinctrl-names = "default"; + gpios = <&gpio1 0 GPIO_ACTIVE_HIGH + &gpio1 1 GPIO_ACTIVE_HIGH + &gpio1 2 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2500 1 + 3100 2 + 3800 3 + 4600 4 + 4800 5 + 4900 6 + 5000 7 >; + }; + + gpio-fan-100-15-18 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 + &pmx_fanalarm_18>; + pinctrl-names = "default"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH + &gpio0 16 GPIO_ACTIVE_HIGH + &gpio0 17 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio0 18 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2500 1 + 3100 2 + 3800 3 + 4600 4 + 4800 5 + 4900 6 + 5000 7 >; + }; + + gpio-fan-100-15-35-1 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 + &pmx_fanalarm_35>; + pinctrl-names = "default"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH + &gpio0 16 GPIO_ACTIVE_HIGH + &gpio0 17 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2500 1 + 3100 2 + 3800 3 + 4600 4 + 4800 5 + 4900 6 + 5000 7 >; + }; + + gpio-fan-100-15-35-3 { + status = "disabled"; + compatible = "gpio-fan"; + pinctrl-0 = <&pmx_fanctrl_15 &pmx_fanctrl_16 &pmx_fanctrl_17 + &pmx_fanalarm_35 &pmx_fanalarm_44 &pmx_fanalarm_45>; + pinctrl-names = "default"; + gpios = <&gpio0 15 GPIO_ACTIVE_HIGH + &gpio0 16 GPIO_ACTIVE_HIGH + &gpio0 17 GPIO_ACTIVE_HIGH>; + alarm-gpios = <&gpio1 3 GPIO_ACTIVE_HIGH + &gpio1 12 GPIO_ACTIVE_HIGH + &gpio1 13 GPIO_ACTIVE_HIGH>; + gpio-fan,speed-map = < 0 0 + 2500 1 + 3100 2 + 3800 3 + 4600 4 + 4800 5 + 4900 6 + 5000 7 >; + }; + + gpio-leds-alarm-12 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_alarmled_12>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:alarm"; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-20 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_20 &pmx_hddled_21 &pmx_hddled_22 + &pmx_hddled_23 &pmx_hddled_24 &pmx_hddled_25 + &pmx_hddled_26 &pmx_hddled_27>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; + }; + + hdd2-green { + label = "synology:green:hdd2"; + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; + }; + + hdd2-amber { + label = "synology:amber:hdd2"; + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; + }; + + hdd3-green { + label = "synology:green:hdd3"; + gpios = <&gpio0 24 GPIO_ACTIVE_LOW>; + }; + + hdd3-amber { + label = "synology:amber:hdd3"; + gpios = <&gpio0 25 GPIO_ACTIVE_LOW>; + }; + + hdd4-green { + label = "synology:green:hdd4"; + gpios = <&gpio0 26 GPIO_ACTIVE_LOW>; + }; + + hdd4-amber { + label = "synology:amber:hdd4"; + gpios = <&gpio0 27 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-21-1 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-21-2 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_21 &pmx_hddled_23 &pmx_hddled_20 &pmx_hddled_22>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio0 21 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio0 23 GPIO_ACTIVE_LOW>; + }; + + hdd2-green { + label = "synology:green:hdd2"; + gpios = <&gpio0 20 GPIO_ACTIVE_LOW>; + }; + + hdd2-amber { + label = "synology:amber:hdd2"; + gpios = <&gpio0 22 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-36 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_36 &pmx_hddled_37 &pmx_hddled_38 + &pmx_hddled_39 &pmx_hddled_40 &pmx_hddled_41 + &pmx_hddled_42 &pmx_hddled_43 &pmx_hddled_44 + &pmx_hddled_45>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + }; + + hdd2-green { + label = "synology:green:hdd2"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + }; + + hdd2-amber { + label = "synology:amber:hdd2"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + }; + + hdd3-green { + label = "synology:green:hdd3"; + gpios = <&gpio1 8 GPIO_ACTIVE_LOW>; + }; + + hdd3-amber { + label = "synology:amber:hdd3"; + gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; + }; + + hdd4-green { + label = "synology:green:hdd4"; + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; + }; + + hdd4-amber { + label = "synology:amber:hdd4"; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; + }; + + hdd5-green { + label = "synology:green:hdd5"; + gpios = <&gpio1 12 GPIO_ACTIVE_LOW>; + }; + + hdd5-amber { + label = "synology:amber:hdd5"; + gpios = <&gpio1 13 GPIO_ACTIVE_LOW>; + }; + }; + + gpio-leds-hdd-38 { + status = "disabled"; + compatible = "gpio-leds"; + pinctrl-0 = <&pmx_hddled_38 &pmx_hddled_39 &pmx_hddled_36 &pmx_hddled_37>; + pinctrl-names = "default"; + + hdd1-green { + label = "synology:green:hdd1"; + gpios = <&gpio1 6 GPIO_ACTIVE_LOW>; + }; + + hdd1-amber { + label = "synology:amber:hdd1"; + gpios = <&gpio1 7 GPIO_ACTIVE_LOW>; + }; + + hdd2-green { + label = "synology:green:hdd2"; + gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; + }; + + hdd2-amber { + label = "synology:amber:hdd2"; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + }; + }; + + regulators-hdd-29 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd1_pwr_29 &pmx_hdd2_pwr_31>; + pinctrl-names = "default"; + + regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd1power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 29 GPIO_ACTIVE_HIGH>; + }; + + regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-30-1 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd1_pwr_30>; + pinctrl-names = "default"; + + regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd1power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-30-2 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34>; + pinctrl-names = "default"; + + regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd1power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; + }; + + regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-30-4 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd1_pwr_30 &pmx_hdd2_pwr_34 + &pmx_hdd3_pwr_44 &pmx_hdd4_pwr_45>; + pinctrl-names = "default"; + + regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd1power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 30 GPIO_ACTIVE_HIGH>; + }; + + regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + }; + + regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "hdd3power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + }; + + regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "hdd4power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-31 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd2_pwr_31>; + pinctrl-names = "default"; + + regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio0 31 GPIO_ACTIVE_HIGH>; + }; + }; + + regulators-hdd-34 { + status = "disabled"; + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_hdd2_pwr_34 &pmx_hdd3_pwr_44 + &pmx_hdd4_pwr_45>; + pinctrl-names = "default"; + + regulator@2 { + compatible = "regulator-fixed"; + reg = <2>; + regulator-name = "hdd2power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 2 GPIO_ACTIVE_HIGH>; + }; + + regulator@3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "hdd3power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + }; + + regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "hdd4power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + startup-delay-us = <5000000>; + gpio = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + }; +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy@0 { + device_type = "ethernet-phy"; + reg = <8>; + }; + + ethphy1: ethernet-phy@1 { + device_type = "ethernet-phy"; + reg = <9>; + }; +}; + +ð0 { + status = "okay"; + + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; + +ð1 { + status = "disabled"; + + ethernet1-port@0 { + phy-handle = <ðphy1>; + }; +}; diff --git a/arch/arm/boot/dts/kirkwood-t5325.dts b/arch/arm/boot/dts/kirkwood-t5325.dts new file mode 100644 index 000000000000..7d1c7677a18f --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-t5325.dts @@ -0,0 +1,208 @@ +/* + * Device Tree file for HP t5325 Thin Client" + * + * Copyright (C) 2014 + * + * Thomas Petazzoni <thomas.petazzoni@free-electrons.com> + * Andrew Lunn <andrew@lunn.ch> + * + * This file is licensed under the terms of the GNU General Public + * License version 2. This program is licensed "as is" without any + * warranty of any kind, whether express or implied. +*/ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" + +/ { + model = "HP t5325 Thin Client"; + compatible = "hp,t5325", "marvell,kirkwood-88f6281", "marvell,kirkwood"; + + memory { + device_type = "memory"; + reg = <0x00000000 0x20000000>; + }; + + chosen { + bootargs = "console=ttyS0,115200n8"; + }; + + mbus { + pcie-controller { + status = "okay"; + + pcie@1,0 { + status = "okay"; + }; + }; + }; + + ocp@f1000000 { + pinctrl: pinctrl@10000 { + pinctrl-0 = <&pmx_i2s &pmx_sysrst>; + pinctrl-names = "default"; + + pmx_button_power: pmx-button_power { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + pmx_power_off: pmx-power-off { + marvell,pins = "mpp48"; + marvell,function = "gpio"; + }; + + pmx_led: pmx-led { + marvell,pins = "mpp21"; + marvell,function = "gpio"; + }; + + pmx_usb_sata_power_enable: pmx-usb-sata-power-enable { + marvell,pins = "mpp44"; + marvell,function = "gpio"; + }; + + /* + * Redefined from kirkwood-6281.dtsi, because + * we don't use SPI CS on MPP0, but on MPP7. + */ + pmx_spi: pmx-spi { + marvell,pins = "mpp1", "mpp2", "mpp3", "mpp7"; + marvell,function = "spi"; + }; + + pmx_sysrst: pmx-sysrst { + marvell,pins = "mpp6"; + marvell,function = "sysrst"; + }; + + pmx_i2s: pmx-i2s { + marvell,pins = "mpp39", "mpp40", "mpp41", "mpp42", + "mpp43"; + marvell,function = "audio"; + }; + }; + + spi@10600 { + pinctrl-0 = <&pmx_spi>; + pinctrl-names = "default"; + status = "okay"; + + flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "st,m25p80"; + spi-max-frequency = <86000000>; + reg = <0>; + mode = <0>; + + partition@0 { + reg = <0x0 0x80000>; + label = "u-boot"; + }; + + partition@1 { + reg = <0x80000 0x40000>; + label = "SSD firmware"; + }; + + partition@2 { + reg = <0xc0000 0x10000>; + label = "u-boot env"; + }; + + partition@3 { + reg = <0xd0000 0x10000>; + label = "permanent u-boot env"; + }; + + partition@4 { + reg = <0xd0000 0x10000>; + label = "permanent u-boot env"; + }; + }; + }; + + i2c@11000 { + status = "okay"; + + alc5621: alc5621@1a { + compatible = "realtek,alc5621"; + reg = <0x1a>; + }; + }; + + serial@12000 { + status = "okay"; + }; + + sata@80000 { + status = "okay"; + nr-ports = <2>; + }; + + audio: audio-controller@a0000 { + status = "okay"; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_usb_sata_power_enable>; + pinctrl-names = "default"; + + usb_power: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "USB-SATA Power"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + regulator-always-on; + regulator-boot-on; + gpio = <&gpio1 12 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_button_power>; + pinctrl-names = "default"; + + button@1 { + label = "Power Button"; + linux,code = <KEY_POWER>; + gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>; + }; + }; + + gpio_poweroff { + compatible = "gpio-poweroff"; + pinctrl-0 = <&pmx_power_off>; + pinctrl-names = "default"; + gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>; + }; + +}; + +&mdio { + status = "okay"; + + ethphy0: ethernet-phy { + device_type = "ethernet-phy"; + reg = <8>; + }; +}; + +ð0 { + status = "okay"; + ethernet0-port@0 { + phy-handle = <ðphy0>; + }; +}; diff --git a/arch/arm/boot/dts/kirkwood-ts419-6281.dts b/arch/arm/boot/dts/kirkwood-ts419-6281.dts new file mode 100644 index 000000000000..aa22aa862857 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ts419-6281.dts @@ -0,0 +1,20 @@ +/* + * Device Tree file for QNAP TS41X with 6281 SoC + * + * Copyright (C) 2013, Andrew Lunn <andrew@lunn.ch> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6281.dtsi" +#include "kirkwood-ts219.dtsi" +#include "kirkwood-ts419.dtsi" + +ðphy0 { reg = <8>; }; +ðphy1 { reg = <0>; }; diff --git a/arch/arm/boot/dts/kirkwood-ts419-6282.dts b/arch/arm/boot/dts/kirkwood-ts419-6282.dts new file mode 100644 index 000000000000..d7512d4cdced --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ts419-6282.dts @@ -0,0 +1,32 @@ +/* + * Device Tree file for QNAP TS41X with 6282 SoC + * + * Copyright (C) 2013, Andrew Lunn <andrew@lunn.ch> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +/dts-v1/; + +#include "kirkwood.dtsi" +#include "kirkwood-6282.dtsi" +#include "kirkwood-ts219.dtsi" +#include "kirkwood-ts419.dtsi" + +/ { + mbus { + pcie-controller { + status = "okay"; + + pcie@2,0 { + status = "okay"; + }; + }; + }; +}; + +ðphy0 { reg = <0>; }; +ðphy1 { reg = <1>; }; diff --git a/arch/arm/boot/dts/kirkwood-ts419.dtsi b/arch/arm/boot/dts/kirkwood-ts419.dtsi new file mode 100644 index 000000000000..1a9c624c7a92 --- /dev/null +++ b/arch/arm/boot/dts/kirkwood-ts419.dtsi @@ -0,0 +1,75 @@ +/* + * Device Tree include file for QNAP TS41X + * + * Copyright (C) 2013, Andrew Lunn <andrew@lunn.ch> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License + * as published by the Free Software Foundation; either version + * 2 of the License, or (at your option) any later version. + */ + +/ { + model = "QNAP TS419 family"; + compatible = "qnap,ts419", "marvell,kirkwood"; + + ocp@f1000000 { + pinctrl: pinctrl@10000 { + pinctrl-names = "default"; + + pmx_USB_copy_button: pmx-USB-copy-button { + marvell,pins = "mpp43"; + marvell,function = "gpio"; + }; + pmx_reset_button: pmx-reset-button { + marvell,pins = "mpp37"; + marvell,function = "gpio"; + }; + /* + * JP1 indicates if an LCD module is installed + * on the serial port (0), or if the port is used + * as a console (1). + */ + pmx_jumper_jp1: pmx-jumper_jp1 { + marvell,pins = "mpp45"; + marvell,function = "gpio"; + }; + + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-0 = <&pmx_reset_button &pmx_USB_copy_button>; + pinctrl-names = "default"; + + button@1 { + label = "USB Copy"; + linux,code = <KEY_COPY>; + gpios = <&gpio1 11 GPIO_ACTIVE_LOW>; + }; + button@2 { + label = "Reset"; + linux,code = <KEY_RESTART>; + gpios = <&gpio1 5 GPIO_ACTIVE_LOW>; + }; + }; +}; + +&mdio { + status = "okay"; + + ethphy1: ethernet-phy@1 { + device_type = "ethernet-phy"; + /* overwrite reg property in board file */ + }; +}; + +ð1 { + status = "okay"; + ethernet1-port@0 { + phy-handle = <ðphy1>; + }; +}; diff --git a/arch/arm/boot/dts/kirkwood.dtsi b/arch/arm/boot/dts/kirkwood.dtsi index 6abf44d257df..90384587c278 100644 --- a/arch/arm/boot/dts/kirkwood.dtsi +++ b/arch/arm/boot/dts/kirkwood.dtsi @@ -24,6 +24,7 @@ aliases { gpio0 = &gpio0; gpio1 = &gpio1; + i2c0 = &i2c0; }; mbus { @@ -111,7 +112,7 @@ clocks = <&gate_clk 7>; }; - i2c@11000 { + i2c0: i2c@11000 { compatible = "marvell,mv64xxx-i2c"; reg = <0x11000 0x20>; #address-cells = <1>; @@ -145,6 +146,11 @@ reg = <0x20000 0x80>, <0x1500 0x20>; }; + system-controller@20000 { + compatible = "marvell,orion-system-controller"; + reg = <0x20000 0x120>; + }; + bridge_intc: bridge-interrupt-ctrl@20110 { compatible = "marvell,orion-bridge-intc"; interrupt-controller; @@ -161,6 +167,11 @@ #clock-cells = <1>; }; + l2: l2-cache@20128 { + compatible = "marvell,kirkwood-cache"; + reg = <0x20128 0x4>; + }; + intc: main-interrupt-ctrl@20200 { compatible = "marvell,orion-intc"; interrupt-controller; @@ -178,7 +189,7 @@ wdt: watchdog-timer@20300 { compatible = "marvell,orion-wdt"; - reg = <0x20300 0x28>; + reg = <0x20300 0x28>, <0x20108 0x4>; interrupt-parent = <&bridge_intc>; interrupts = <3>; clocks = <&gate_clk 7>; @@ -300,5 +311,14 @@ #phy-cells = <0>; status = "ok"; }; + + audio0: audio-controller@a0000 { + compatible = "marvell,kirkwood-audio"; + reg = <0xa0000 0x2210>; + interrupts = <24>; + clocks = <&gate_clk 9>; + clock-names = "internal"; + status = "disabled"; + }; }; }; diff --git a/arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi b/arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi new file mode 100644 index 000000000000..73e272fadc20 --- /dev/null +++ b/arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi @@ -0,0 +1,58 @@ +/* + * Common file for GPMC connected smsc9221 on omaps + * + * Compared to smsc911x, smsc9221 (and others like smsc9217 + * or smsc 9218) has faster timings, leading to higher + * bandwidth. + * + * Note that the board specifc DTS file needs to specify + * ranges, pinctrl, reg, interrupt parent and interrupts. + */ + +/ { + vddvario: regulator-vddvario { + compatible = "regulator-fixed"; + regulator-name = "vddvario"; + regulator-always-on; + }; + + vdd33a: regulator-vdd33a { + compatible = "regulator-fixed"; + regulator-name = "vdd33a"; + regulator-always-on; + }; +}; + +&gpmc { + ethernet@gpmc { + compatible = "smsc,lan9221","smsc,lan9115"; + bank-width = <2>; + + gpmc,mux-add-data; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <42>; + gpmc,cs-wr-off-ns = <36>; + gpmc,adv-on-ns = <6>; + gpmc,adv-rd-off-ns = <12>; + gpmc,adv-wr-off-ns = <12>; + gpmc,oe-on-ns = <0>; + gpmc,oe-off-ns = <42>; + gpmc,we-on-ns = <0>; + gpmc,we-off-ns = <36>; + gpmc,rd-cycle-ns = <60>; + gpmc,wr-cycle-ns = <54>; + gpmc,access-ns = <36>; + gpmc,page-burst-access-ns = <0>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <0>; + gpmc,wr-data-mux-bus-ns = <18>; + gpmc,wr-access-ns = <42>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-diffcsen; + + vddvario-supply = <&vddvario>; + vdd33a-supply = <&vdd33a>; + reg-io-width = <4>; + smsc,save-mac-address; + }; +}; diff --git a/arch/arm/boot/dts/omap2420.dtsi b/arch/arm/boot/dts/omap2420.dtsi index 60c605de22dd..85b1fb014c43 100644 --- a/arch/arm/boot/dts/omap2420.dtsi +++ b/arch/arm/boot/dts/omap2420.dtsi @@ -99,6 +99,7 @@ dmas = <&sdma 31>, <&sdma 32>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp2: mcbsp@48076000 { @@ -112,6 +113,7 @@ dmas = <&sdma 33>, <&sdma 34>; dma-names = "tx", "rx"; + status = "disabled"; }; msdi1: mmc@4809c000 { diff --git a/arch/arm/boot/dts/omap2430.dtsi b/arch/arm/boot/dts/omap2430.dtsi index d624345666f5..9d2f028fd687 100644 --- a/arch/arm/boot/dts/omap2430.dtsi +++ b/arch/arm/boot/dts/omap2430.dtsi @@ -113,6 +113,7 @@ dmas = <&sdma 31>, <&sdma 32>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp2: mcbsp@48076000 { @@ -128,6 +129,7 @@ dmas = <&sdma 33>, <&sdma 34>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp3: mcbsp@4808c000 { @@ -143,6 +145,7 @@ dmas = <&sdma 17>, <&sdma 18>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp4: mcbsp@4808e000 { @@ -158,6 +161,7 @@ dmas = <&sdma 19>, <&sdma 20>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp5: mcbsp@48096000 { @@ -173,6 +177,7 @@ dmas = <&sdma 21>, <&sdma 22>; dma-names = "tx", "rx"; + status = "disabled"; }; mmc1: mmc@4809c000 { diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index 447e714d435b..cba357023878 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -234,3 +234,7 @@ regulator-max-microvolt = <1800000>; regulator-always-on; }; + +&mcbsp2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index 5053766d369b..d01e9a76c5da 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -211,3 +211,7 @@ regulator-max-microvolt = <1800000>; regulator-always-on; }; + +&mcbsp2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/omap3-cm-t3517.dts b/arch/arm/boot/dts/omap3-cm-t3517.dts new file mode 100644 index 000000000000..d00502f4fd9b --- /dev/null +++ b/arch/arm/boot/dts/omap3-cm-t3517.dts @@ -0,0 +1,136 @@ +/* + * Support for CompuLab CM-T3517 + */ +/dts-v1/; + +#include "am3517.dtsi" +#include "omap3-cm-t3x.dtsi" + +/ { + model = "CompuLab CM-T3517"; + compatible = "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3"; + + vmmc: regulator-vmmc { + compatible = "regulator-fixed"; + regulator-name = "vmmc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + wl12xx_vmmc2: wl12xx_vmmc2 { + compatible = "regulator-fixed"; + regulator-name = "vw1271"; + pinctrl-names = "default"; + pinctrl-0 = < + &wl12xx_wkup_pins + &wl12xx_core_pins + >; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + gpio = <&gpio1 6 GPIO_ACTIVE_HIGH >; /* gpio6 */ + startup-delay-us = <20000>; + enable-active-high; + }; + + wl12xx_vaux2: wl12xx_vaux2 { + compatible = "regulator-fixed"; + regulator-name = "vwl1271_vaux2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; +}; + +&omap3_pmx_wkup { + + wl12xx_wkup_pins: pinmux_wl12xx_wkup_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */ + OMAP3_WKUP_IOPAD(0x2a12, PIN_OUTPUT | MUX_MODE4) /* sys_boot4.gpio_6 */ + >; + }; +}; + +&omap3_pmx_core { + + phy1_reset_pins: pinmux_hsusb1_phy_reset_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE4) /* uart2_tx.gpio_146 */ + >; + }; + + phy2_reset_pins: pinmux_hsusb2_phy_reset_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x217a, PIN_OUTPUT | MUX_MODE4) /* uart2_rx.gpio_147 */ + >; + }; + + otg_drv_vbus: pinmux_otg_drv_vbus { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2210, PIN_INPUT_PULLDOWN | MUX_MODE0) /* rmii_50Mhz_clk.usb0_drvvbus */ + >; + }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + >; + }; + + wl12xx_core_pins: pinmux_wl12xx_core_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs5.gpio_56 */ + OMAP3_CORE1_IOPAD(0x2176, PIN_INPUT_PULLUP | MUX_MODE4) /* uart2_rts.gpio_145 */ + >; + }; + + usb_hub_pins: pinmux_usb_hub_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2184, PIN_OUTPUT | MUX_MODE4) /* mcbsp4_clkx.gpio_152 - USB HUB RST */ + >; + }; +}; + +&hsusb1_phy { + pinctrl-names = "default"; + pinctrl-0 = <&phy1_reset_pins>; + reset-gpios = <&gpio5 18 GPIO_ACTIVE_LOW>; +}; + +&hsusb2_phy { + pinctrl-names = "default"; + pinctrl-0 = <&phy2_reset_pins>; + reset-gpios = <&gpio5 19 GPIO_ACTIVE_LOW>; +}; + +&davinci_emac { + status = "okay"; +}; + +&davinci_mdio { + status = "okay"; +}; + +&am35x_otg_hs { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&otg_drv_vbus>; +}; + +&mmc1 { + vmmc-supply = <&vmmc>; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&wl12xx_vmmc2>; + vmmc_aux-supply = <&wl12xx_vaux2>; + non-removable; + bus-width = <4>; + cap-power-off-card; +}; diff --git a/arch/arm/boot/dts/omap3-cm-t3530.dts b/arch/arm/boot/dts/omap3-cm-t3530.dts new file mode 100644 index 000000000000..d1458496520e --- /dev/null +++ b/arch/arm/boot/dts/omap3-cm-t3530.dts @@ -0,0 +1,48 @@ +/* + * Support for CompuLab CM-T3530 + */ +/dts-v1/; + +#include "omap34xx.dtsi" +#include "omap3-cm-t3x30.dtsi" + +/ { + model = "CompuLab CM-T3530"; + compatible = "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3"; + + /* Regulator to trigger the reset signal of the Wifi module */ + mmc2_sdio_reset: regulator-mmc2-sdio-reset { + compatible = "regulator-fixed"; + regulator-name = "regulator-mmc2-sdio-reset"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&twl_gpio 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&omap3_pmx_core { + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dir_dat0 */ + OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dir_dat1 */ + OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dir_cmd */ + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */ + >; + }; +}; + +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&mmc2_sdio_reset>; + non-removable; + bus-width = <4>; + cap-power-off-card; +}; diff --git a/arch/arm/boot/dts/omap3-cm-t3730.dts b/arch/arm/boot/dts/omap3-cm-t3730.dts index 486f4d6c4219..b3f9a50b3bc8 100644 --- a/arch/arm/boot/dts/omap3-cm-t3730.dts +++ b/arch/arm/boot/dts/omap3-cm-t3730.dts @@ -32,57 +32,26 @@ }; &omap3_pmx_core { - mmc1_pins: pinmux_mmc1_pins { - pinctrl-single,pins = < - 0x114 (PIN_OUTPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ - 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ - 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ - 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ - 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ - 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ - >; - }; mmc2_pins: pinmux_mmc2_pins { pinctrl-single,pins = < - 0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ - 0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ - 0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ - 0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ - 0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ - 0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ - >; - }; - - smsc1_pins: pinmux_smsc1_pins { - pinctrl-single,pins = < - 0x88 (PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs5.gpmc_ncs5 */ - 0x16a (PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 */ - >; - }; - - uart3_pins: pinmux_uart3_pins { - pinctrl-single,pins = < - 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ - 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ >; }; wl12xx_gpio: pinmux_wl12xx_gpio { pinctrl-single,pins = < - 0xb2 (PIN_OUTPUT | MUX_MODE4) /* dss_data3.gpio_73 */ - 0x134 (PIN_INPUT | MUX_MODE4) /* sdmmc2_dat4.gpio_136 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4) /* dss_data3.gpio_73 */ + OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT | MUX_MODE4) /* sdmmc2_dat4.gpio_136 */ >; }; }; -&mmc1 { - vmmc-supply = <&vmmc1>; - bus-width = <4>; - pinctrl-names = "default"; - pinctrl-0 = <&mmc1_pins>; -}; - &mmc2 { pinctrl-names = "default"; pinctrl-0 = <&mmc2_pins>; @@ -92,13 +61,3 @@ bus-width = <4>; cap-power-off-card; }; - -&smsc1 { - pinctrl-names = "default"; - pinctrl-0 = <&smsc1_pins>; -}; - -&uart3 { - pinctrl-names = "default"; - pinctrl-0 = <&uart3_pins>; -}; diff --git a/arch/arm/boot/dts/omap3-cm-t3x.dtsi b/arch/arm/boot/dts/omap3-cm-t3x.dtsi new file mode 100644 index 000000000000..c671a2299ea8 --- /dev/null +++ b/arch/arm/boot/dts/omap3-cm-t3x.dtsi @@ -0,0 +1,110 @@ +/* + * Common support for CompuLab CM-T3x CoMs + */ + +/ { + + memory { + device_type = "memory"; + reg = <0x80000000 0x10000000>; /* 256 MB */ + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&green_led_pins>; + ledb { + label = "cm-t3x:green"; + gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>; /* gpio186 */ + linux,default-trigger = "heartbeat"; + }; + }; + + /* HS USB Port 1 Power */ + hsusb1_power: hsusb1_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb1_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <70000>; + }; + + /* HS USB Port 2 Power */ + hsusb2_power: hsusb2_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb2_vbus"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + startup-delay-us = <70000>; + }; + + /* HS USB Host PHY on PORT 1 */ + hsusb1_phy: hsusb1_phy { + compatible = "usb-nop-xceiv"; + vcc-supply = <&hsusb1_power>; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + vcc-supply = <&hsusb2_power>; + }; +}; + +&omap3_pmx_core { + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; + + green_led_pins: pinmux_green_led_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21e2, PIN_OUTPUT | MUX_MODE4) /* sys_clkout2.gpio_186 */ + >; + }; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + bus-width = <4>; +}; + +&mmc3 { + status = "disabled"; +}; + +&i2c1 { + clock-frequency = <400000>; +}; + +&i2c3 { + clock-frequency = <400000>; +}; +&usbhshost { + port1-mode = "ehci-phy"; + port2-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <&hsusb1_phy &hsusb2_phy>; +}; diff --git a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi index 3a9f004d8924..d00055809e31 100644 --- a/arch/arm/boot/dts/omap3-cm-t3x30.dtsi +++ b/arch/arm/boot/dts/omap3-cm-t3x30.dtsi @@ -1,28 +1,16 @@ /* - * Common support for CompuLab CM-T3530 and CM-T3730 + * Common support for CompuLab CM-T3x30 CoMs */ -/ { - memory { - device_type = "memory"; - reg = <0x80000000 0x10000000>; /* 256 MB */ - }; +#include "omap3-cm-t3x.dtsi" +/ { cpus { cpu@0 { cpu0-supply = <&vcc>; }; }; - leds { - compatible = "gpio-leds"; - ledb { - label = "cm-t35:green"; - gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>; /* gpio186 */ - linux,default-trigger = "heartbeat"; - }; - }; - vddvario: regulator-vddvario { compatible = "regulator-fixed"; regulator-name = "vddvario"; @@ -36,11 +24,40 @@ }; }; +&omap3_pmx_core { + + smsc1_pins: pinmux_smsc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20b8, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs5.gpmc_ncs5 */ + OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 */ + >; + }; + + hsusb0_pins: pinmux_hsusb0_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */ + OMAP3_CORE1_IOPAD(0x21a2, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */ + OMAP3_CORE1_IOPAD(0x21a4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */ + OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */ + OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data0.hsusb2_data0 */ + OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */ + OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */ + OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data3 */ + OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data4 */ + OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data5 */ + OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data6 */ + OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ + >; + }; +}; + &gpmc { ranges = <5 0 0x2c000000 0x01000000>; smsc1: ethernet@5,0 { compatible = "smsc,lan9221", "smsc,lan9115"; + pinctrl-names = "default"; + pinctrl-0 = <&smsc1_pins>; interrupt-parent = <&gpio6>; interrupts = <3 IRQ_TYPE_LEVEL_LOW>; reg = <5 0 0xff>; @@ -74,8 +91,6 @@ }; &i2c1 { - clock-frequency = <400000>; - twl: twl@48 { reg = <0x48>; interrupts = <7>; /* SYS_NIRQ cascaded to intc */ @@ -86,10 +101,31 @@ #include "twl4030.dtsi" #include "twl4030_omap3.dtsi" -&i2c3 { - clock-frequency = <400000>; +&mmc1 { + vmmc-supply = <&vmmc1>; }; &twl_gpio { ti,use-leds; + /* pullups: BIT(0) */ + ti,pullups = <0x000001>; +}; + +&hsusb1_phy { + reset-gpios = <&twl_gpio 6 GPIO_ACTIVE_LOW>; +}; + +&hsusb2_phy { + reset-gpios = <&twl_gpio 7 GPIO_ACTIVE_LOW>; +}; + +&usb_otg_hs { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb0_pins>; + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; }; diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts b/arch/arm/boot/dts/omap3-devkit8000.dts index 4665421bb7bc..bf5a515a3247 100644 --- a/arch/arm/boot/dts/omap3-devkit8000.dts +++ b/arch/arm/boot/dts/omap3-devkit8000.dts @@ -101,20 +101,8 @@ status = "disabled"; }; -&mcbsp1 { - status = "disabled"; -}; - -&mcbsp3 { - status = "disabled"; -}; - -&mcbsp4 { - status = "disabled"; -}; - -&mcbsp5 { - status = "disabled"; +&mcbsp2 { + status = "okay"; }; &gpmc { diff --git a/arch/arm/boot/dts/omap3-gta04.dts b/arch/arm/boot/dts/omap3-gta04.dts index d3b253bbc885..f8ad125fa46f 100644 --- a/arch/arm/boot/dts/omap3-gta04.dts +++ b/arch/arm/boot/dts/omap3-gta04.dts @@ -36,6 +36,14 @@ gpio-key,wakeup; }; }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "gta04"; + + ti,mcbsp = <&mcbsp2>; + ti,codec = <&twl_audio>; + }; }; &omap3_pmx_core { @@ -80,6 +88,12 @@ interrupts = <7>; /* SYS_NIRQ cascaded to intc */ interrupt-parent = <&intc>; }; + + twl_audio: audio { + compatible = "ti,twl4030-audio"; + codec { + }; + }; }; #include "twl4030.dtsi" @@ -96,6 +110,14 @@ interrupts = <17 IRQ_TYPE_EDGE_RISING>; }; + /* accelerometer */ + bma180@41 { + compatible = "bosch,bma180"; + reg = <0x41>; + interrupt-parent = <&gpio3>; + interrupts = <19 IRQ_TYPE_LEVEL_HIGH>; + }; + /* leds */ tca6507@45 { compatible = "ti,tca6507"; @@ -124,6 +146,22 @@ reg = <0x4>; }; }; + + /* compass aka magnetometer */ + hmc5843@1e { + compatible = "honeywell,hmc5843"; + reg = <0x1e>; + }; + + /* touchscreen */ + tsc2007@48 { + compatible = "ti,tsc2007"; + reg = <0x48>; + interrupt-parent = <&gpio6>; + interrupts = <0 IRQ_TYPE_EDGE_FALLING>; + gpios = <&gpio6 0 GPIO_ACTIVE_LOW>; + ti,x-plate-ohms = <600>; + }; }; &i2c3 { @@ -148,7 +186,9 @@ }; &mmc2 { - status = "disabled"; + vmmc-supply = <&vaux4>; + bus-width = <4>; + ti,non-removable; }; &mmc3 { @@ -170,3 +210,12 @@ pinctrl-0 = <&uart3_pins>; }; +&charger { + bb_uvolt = <3200000>; + bb_uamp = <150>; +}; + +&vaux4 { + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <3150000>; +}; diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index c17009323520..b97736d98a64 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -170,6 +170,7 @@ &mcbsp2 { pinctrl-names = "default"; pinctrl-0 = <&mcbsp2_pins>; + status = "okay"; }; &mmc1 { diff --git a/arch/arm/boot/dts/omap3-lilly-a83x.dtsi b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi new file mode 100644 index 000000000000..6369d9f43ca2 --- /dev/null +++ b/arch/arm/boot/dts/omap3-lilly-a83x.dtsi @@ -0,0 +1,459 @@ +/* + * Copyright (C) 2014 Christoph Fritz <chf.fritzc@googlemail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ + +#include "omap36xx.dtsi" + +/ { + model = "INCOstartec LILLY-A83X module (DM3730)"; + compatible = "incostartec,omap3-lilly-a83x", "ti,omap36xx", "ti,omap3"; + + chosen { + bootargs = "console=ttyO0,115200n8 vt.global_cursor_default=0 consoleblank=0"; + }; + + memory { + device_type = "memory"; + reg = <0x80000000 0x8000000>; /* 128 MB */ + }; + + leds { + compatible = "gpio-leds"; + + led1 { + label = "lilly-a83x::led1"; + gpios = <&gpio1 29 GPIO_ACTIVE_LOW>; + linux,default-trigger = "default-on"; + }; + + }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "lilly-a83x"; + + ti,mcbsp = <&mcbsp2>; + ti,codec = <&twl_audio>; + }; + + reg_vcc3: vcc3 { + compatible = "regulator-fixed"; + regulator-name = "VCC3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + hsusb1_phy: hsusb1_phy { + compatible = "usb-nop-xceiv"; + vcc-supply = <®_vcc3>; + }; +}; + +&omap3_pmx_wkup { + pinctrl-names = "default"; + + lan9221_pins: pinmux_lan9221_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a5a, PIN_INPUT | MUX_MODE4) /* reserved.gpio_129 */ + >; + }; + + tsc2048_pins: pinmux_tsc2048_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a16, PIN_INPUT_PULLUP | MUX_MODE4) /* sys_boot6.gpio_8 */ + >; + }; + + mmc1cd_pins: pinmux_mmc1cd_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a56, PIN_INPUT | MUX_MODE4) /* reserved.gpio_126 */ + >; + }; +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + + uart1_pins: pinmux_uart1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE0) /* uart1_tx.uart1_tx */ + OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE0) /* uart1_rts.uart1_rts */ + OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT | MUX_MODE0) /* uart1_cts.uart1_cts */ + OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */ + >; + }; + + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2170, PIN_OUTPUT | MUX_MODE1) /* mcbsp3_clkx.uart2_tx */ + OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE1) /* mcbsp3_fsx.uart2_rx */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21ba ,PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl.i2c1_scl */ + OMAP3_CORE1_IOPAD(0x21bc ,PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda.i2c1_sda */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl.i2c2_scl */ + OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda.i2c2_sda */ + >; + }; + + i2c3_pins: pinmux_i2c3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl.i2c3_scl */ + OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda.i2c3_sda */ + >; + }; + + hsusb1_pins: pinmux_hsusb1_pins { + pinctrl-single,pins = < + + /* GPIO 182 controls USB-Hub reset. But USB-Phy its + * reset can't be controlled. So we clamp this GPIO to + * high (PIN_OFF_OUTPUT_HIGH) to always enable USB-Hub. + */ + + OMAP3_CORE1_IOPAD(0x21de, PIN_OUTPUT_PULLUP | PIN_OFF_OUTPUT_HIGH | MUX_MODE4) /* mcspi2_cs1.gpio_182 */ + >; + }; + + hsusb_otg_pins: pinmux_hsusb_otg_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */ + OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */ + OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */ + OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */ + OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */ + OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */ + OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */ + OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */ + OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */ + OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */ + OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */ + OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; + + spi2_pins: pinmux_spi2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcspi2_clk.mcspi2_clk */ + OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcspi2_simo.mcspi2_simo */ + OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcspi2_somi.mcspi2_somi */ + OMAP3_CORE1_IOPAD(0x21dc, PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs0.mcspi2_cs0 */ + >; + }; +}; + +&omap3_pmx_core2 { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusb1_2_pins + >; + + hsusb1_2_pins: pinmux_hsusb1_2_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25d8, PIN_OUTPUT | MUX_MODE3) /* etk_clk.hsusb1_stp */ + OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT | MUX_MODE3) /* etk_ctl.hsusb1_clk */ + OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE3) /* etk_d0.hsusb1_data0 */ + OMAP3630_CORE2_IOPAD(0x25de, PIN_INPUT | MUX_MODE3) /* etk_d1.hsusb1_data1 */ + OMAP3630_CORE2_IOPAD(0x25e0, PIN_INPUT | MUX_MODE3) /* etk_d2.hsusb1_data2 */ + OMAP3630_CORE2_IOPAD(0x25e2, PIN_INPUT | MUX_MODE3) /* etk_d3.hsusb1_data7 */ + OMAP3630_CORE2_IOPAD(0x25e4, PIN_INPUT | MUX_MODE3) /* etk_d4.hsusb1_data4 */ + OMAP3630_CORE2_IOPAD(0x25e6, PIN_INPUT | MUX_MODE3) /* etk_d5.hsusb1_data5 */ + OMAP3630_CORE2_IOPAD(0x25e8, PIN_INPUT | MUX_MODE3) /* etk_d6.hsusb1_data6 */ + OMAP3630_CORE2_IOPAD(0x25ea, PIN_INPUT | MUX_MODE3) /* etk_d7.hsusb1_data3 */ + OMAP3630_CORE2_IOPAD(0x25ec, PIN_INPUT | MUX_MODE3) /* etk_d8.hsusb1_dir */ + OMAP3630_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE3) /* etk_d9.hsusb1_nxt */ + >; + }; + + gpio1_pins: pinmux_gpio1_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25fa, PIN_OUTPUT_PULLDOWN | MUX_MODE4) /* etk_d15.gpio_29 */ + >; + }; + +}; + +&gpio1 { + pinctrl-names = "default"; + pinctrl-0 = <&gpio1_pins>; +}; + +&gpio6 { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb1_pins>; +}; + +&i2c1 { + clock-frequency = <2600000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + twl_audio: audio { + compatible = "ti,twl4030-audio"; + codec { + }; + }; + }; +}; + +#include "twl4030.dtsi" +#include "twl4030_omap3.dtsi" + +&twl { + vmmc1: regulator-vmmc1 { + regulator-always-on; + }; + + vdd1: regulator-vdd1 { + regulator-always-on; + }; + + vdd2: regulator-vdd2 { + regulator-always-on; + }; +}; + +&i2c2 { + clock-frequency = <2600000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; +}; + +&i2c3 { + clock-frequency = <2600000>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; + gpiom1: gpio@20 { + compatible = "mcp,mcp23017"; + gpio-controller; + #gpio-cells = <2>; + reg = <0x20>; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&uart1_pins>; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; +}; + +&uart4 { + status = "disabled"; +}; + +&mmc1 { + cd-gpios = <&gpio4 30 IRQ_TYPE_LEVEL_LOW>; + cd-inverted; + vmmc-supply = <&vmmc1>; + bus-width = <4>; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins &mmc1cd_pins>; + cap-sdio-irq; + cap-sd-highspeed; + cap-mmc-highspeed; +}; + +&mmc2 { + status = "disabled"; +}; + +&mmc3 { + status = "disabled"; +}; + +&mcspi2 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins>; + + tsc2046@0 { + reg = <0>; /* CS0 */ + compatible = "ti,tsc2046"; + interrupt-parent = <&gpio1>; + interrupts = <8 0>; /* boot6 / gpio_8 */ + spi-max-frequency = <1000000>; + pendown-gpio = <&gpio1 8 0>; + vcc-supply = <®_vcc3>; + pinctrl-names = "default"; + pinctrl-0 = <&tsc2048_pins>; + + ti,x-min = <300>; + ti,x-max = <3000>; + ti,y-min = <600>; + ti,y-max = <3600>; + ti,x-plate-ohms = <80>; + ti,pressure-max = <255>; + ti,swap-xy; + + linux,wakeup; + }; +}; + +&usbhsehci { + phys = <&hsusb1_phy>; +}; + +&usbhshost { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb1_2_pins>; + num-ports = <2>; + port1-mode = "ehci-phy"; +}; + +&usb_otg_hs { + pinctrl-names = "default"; + pinctrl-0 = <&hsusb_otg_pins>; + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000>, + <7 0 0x15000000 0x01000000>; + + nand@0,0 { + reg = <0 0 0x1000000>; + nand-bus-width = <16>; + ti,nand-ecc-opt = "bch8"; + /* no elm on omap3 */ + + gpmc,mux-add-data = <0>; + gpmc,device-nand; + gpmc,device-width = <2>; + gpmc,wait-pin = <0>; + gpmc,wait-monitoring-ns = <0>; + gpmc,burst-length= <4>; + gpmc,cs-on-ns = <0>; + gpmc,cs-rd-off-ns = <100>; + gpmc,cs-wr-off-ns = <100>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <100>; + gpmc,adv-wr-off-ns = <100>; + gpmc,oe-on-ns = <5>; + gpmc,oe-off-ns = <75>; + gpmc,we-on-ns = <5>; + gpmc,we-off-ns = <75>; + gpmc,rd-cycle-ns = <100>; + gpmc,wr-cycle-ns = <100>; + gpmc,access-ns = <60>; + gpmc,page-burst-access-ns = <5>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-delay-ns = <50>; + gpmc,wr-data-mux-bus-ns = <75>; + gpmc,wr-access-ns = <155>; + + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "MLO"; + reg = <0 0x80000>; + }; + + partition@0x80000 { + label = "u-boot"; + reg = <0x80000 0x1e0000>; + }; + + partition@0x260000 { + label = "u-boot-environment"; + reg = <0x260000 0x20000>; + }; + + partition@0x280000 { + label = "kernel"; + reg = <0x280000 0x500000>; + }; + + partition@0x780000 { + label = "filesystem"; + reg = <0x780000 0xf880000>; + }; + }; + + ethernet@7,0 { + compatible = "smsc,lan9221", "smsc,lan9115"; + bank-width = <2>; + gpmc,mux-add-data = <2>; + gpmc,cs-on-ns = <10>; + gpmc,cs-rd-off-ns = <60>; + gpmc,cs-wr-off-ns = <60>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <10>; + gpmc,adv-wr-off-ns = <10>; + gpmc,oe-on-ns = <10>; + gpmc,oe-off-ns = <60>; + gpmc,we-on-ns = <10>; + gpmc,we-off-ns = <60>; + gpmc,rd-cycle-ns = <100>; + gpmc,wr-cycle-ns = <100>; + gpmc,access-ns = <50>; + gpmc,page-burst-access-ns = <5>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <75>; + gpmc,wr-data-mux-bus-ns = <15>; + gpmc,wr-access-ns = <75>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-diffcsen; + vddvario-supply = <®_vcc3>; + vdd33a-supply = <®_vcc3>; + reg-io-width = <4>; + interrupt-parent = <&gpio5>; + interrupts = <1 0x2>; + reg = <7 0 0xff>; + pinctrl-names = "default"; + pinctrl-0 = <&lan9221_pins>; + phy-mode = "mii"; + }; +}; diff --git a/arch/arm/boot/dts/omap3-lilly-dbb056.dts b/arch/arm/boot/dts/omap3-lilly-dbb056.dts new file mode 100644 index 000000000000..834f7c65f62d --- /dev/null +++ b/arch/arm/boot/dts/omap3-lilly-dbb056.dts @@ -0,0 +1,170 @@ +/* + * Copyright (C) 2014 Christoph Fritz <chf.fritzc@googlemail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + */ +/dts-v1/; + +#include "omap3-lilly-a83x.dtsi" + +/ { + model = "INCOstartec LILLY-DBB056 (DM3730)"; + compatible = "incostartec,omap3-lilly-dbb056", "incostartec,omap3-lilly-a83x", "ti,omap36xx", "ti,omap3"; +}; + +&twl { + vaux2: regulator-vaux2 { + compatible = "ti,twl4030-vaux2"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + }; +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = <&lcd_pins>; + + lan9117_pins: pinmux_lan9117_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2114, PIN_INPUT | MUX_MODE4) /* cam_fld.gpio_98 */ + >; + }; + + gpio4_pins: pinmux_gpio4_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x212e, PIN_INPUT | MUX_MODE4) /* cam_xclkb.gpio_111 -> sja1000 IRQ */ + >; + }; + + gpio5_pins: pinmux_gpio5_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x218c, PIN_OUTPUT | PIN_OFF_OUTPUT_HIGH | MUX_MODE4) /* mcbsp1_clk.gpio_156 -> enable DSS */ + >; + }; + + lcd_pins: pinmux_lcd_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20d4, PIN_OUTPUT | MUX_MODE0) /* dss_pclk.dss_pclk */ + OMAP3_CORE1_IOPAD(0x20d6, PIN_OUTPUT | MUX_MODE0) /* dss_hsync.dss_hsync */ + OMAP3_CORE1_IOPAD(0x20d8, PIN_OUTPUT | MUX_MODE0) /* dss_vsync.dss_vsync */ + OMAP3_CORE1_IOPAD(0x20da, PIN_OUTPUT | MUX_MODE0) /* dss_acbias.dss_acbias */ + OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE0) /* dss_data0.dss_data0 */ + OMAP3_CORE1_IOPAD(0x20de, PIN_OUTPUT | MUX_MODE0) /* dss_data1.dss_data1 */ + OMAP3_CORE1_IOPAD(0x20e0, PIN_OUTPUT | MUX_MODE0) /* dss_data2.dss_data2 */ + OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE0) /* dss_data3.dss_data3 */ + OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE0) /* dss_data4.dss_data4 */ + OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE0) /* dss_data5.dss_data5 */ + OMAP3_CORE1_IOPAD(0x20e8, PIN_OUTPUT | MUX_MODE0) /* dss_data6.dss_data6 */ + OMAP3_CORE1_IOPAD(0x20ea, PIN_OUTPUT | MUX_MODE0) /* dss_data7.dss_data7 */ + OMAP3_CORE1_IOPAD(0x20ec, PIN_OUTPUT | MUX_MODE0) /* dss_data8.dss_data8 */ + OMAP3_CORE1_IOPAD(0x20ee, PIN_OUTPUT | MUX_MODE0) /* dss_data9.dss_data9 */ + OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE0) /* dss_data10.dss_data10 */ + OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE0) /* dss_data11.dss_data11 */ + OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE0) /* dss_data12.dss_data12 */ + OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE0) /* dss_data13.dss_data13 */ + OMAP3_CORE1_IOPAD(0x20f8, PIN_OUTPUT | MUX_MODE0) /* dss_data14.dss_data14 */ + OMAP3_CORE1_IOPAD(0x20fa, PIN_OUTPUT | MUX_MODE0) /* dss_data15.dss_data15 */ + OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE0) /* dss_data16.dss_data16 */ + OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE0) /* dss_data17.dss_data17 */ + >; + }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + OMAP3_CORE1_IOPAD(0x2164, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat4.sdmmc2_dir_dat0 */ + OMAP3_CORE1_IOPAD(0x2166, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat5.sdmmc2_dir_dat1 */ + OMAP3_CORE1_IOPAD(0x2168, PIN_OUTPUT | MUX_MODE1) /* sdmmc2_dat6.sdmmc2_dir_cmd */ + OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT | MUX_MODE1) /* sdmmc2_dat7.sdmmc2_clkin */ + OMAP3_CORE1_IOPAD(0x219a, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_cts_rctx.gpio_163 -> wp */ + OMAP3_CORE1_IOPAD(0x219c, PIN_INPUT_PULLUP | MUX_MODE4) /* uart3_rts_sd.gpio_164 -> cd */ + >; + }; + + spi1_pins: pinmux_spi1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ + OMAP3_CORE1_IOPAD(0x21ca, PIN_INPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ + OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ + OMAP3_CORE1_IOPAD(0x21ce, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ + >; + }; +}; + +&gpio4 { + pinctrl-names = "default"; + pinctrl-0 = <&gpio4_pins>; +}; + +&gpio5 { + pinctrl-names = "default"; + pinctrl-0 = <&gpio5_pins>; +}; + +&mmc2 { + status = "okay"; + bus-width = <4>; + vmmc-supply = <&vmmc1>; + cd-gpios = <&gpio6 4 0>; /* gpio_164 */ + wp-gpios = <&gpio6 3 0>; /* gpio_163 */ + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + ti,dual-volt; +}; + +&mcspi1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&spi1_pins>; +}; + +&gpmc { + ranges = <0 0 0x30000000 0x1000000>, /* nand assigned by COM a83x */ + <4 0 0x20000000 0x01000000>, + <7 0 0x15000000 0x01000000>; /* eth assigend by COM a83x */ + + ethernet@4,0 { + compatible = "smsc,lan9117", "smsc,lan9115"; + bank-width = <2>; + gpmc,mux-add-data = <2>; + gpmc,cs-on-ns = <10>; + gpmc,cs-rd-off-ns = <65>; + gpmc,cs-wr-off-ns = <65>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <10>; + gpmc,adv-wr-off-ns = <10>; + gpmc,oe-on-ns = <10>; + gpmc,oe-off-ns = <65>; + gpmc,we-on-ns = <10>; + gpmc,we-off-ns = <65>; + gpmc,rd-cycle-ns = <100>; + gpmc,wr-cycle-ns = <100>; + gpmc,access-ns = <60>; + gpmc,page-burst-access-ns = <5>; + gpmc,bus-turnaround-ns = <0>; + gpmc,cycle2cycle-delay-ns = <75>; + gpmc,wr-data-mux-bus-ns = <15>; + gpmc,wr-access-ns = <75>; + gpmc,cycle2cycle-samecsen; + gpmc,cycle2cycle-diffcsen; + vddvario-supply = <®_vcc3>; + vdd33a-supply = <®_vcc3>; + reg-io-width = <4>; + interrupt-parent = <&gpio4>; + interrupts = <2 0x2>; + reg = <4 0 0xff>; + pinctrl-names = "default"; + pinctrl-0 = <&lan9117_pins>; + phy-mode = "mii"; + smsc,force-internal-phy; + }; +}; diff --git a/arch/arm/boot/dts/omap3-n900.dts b/arch/arm/boot/dts/omap3-n900.dts index 0bf40c90faba..d1c3d99dc947 100644 --- a/arch/arm/boot/dts/omap3-n900.dts +++ b/arch/arm/boot/dts/omap3-n900.dts @@ -74,6 +74,11 @@ }; }; + isp1704: isp1704 { + compatible = "nxp,isp1704"; + nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>; + usb-phy = <&usb2_phy>; + }; }; &omap3_pmx_core { @@ -254,6 +259,61 @@ }; }; +&twl_keypad { + linux,keymap = < 0x00000010 /* KEY_Q */ + 0x00010018 /* KEY_O */ + 0x00020019 /* KEY_P */ + 0x00030033 /* KEY_COMMA */ + 0x0004000e /* KEY_BACKSPACE */ + 0x0006001e /* KEY_A */ + 0x0007001f /* KEY_S */ + + 0x01000011 /* KEY_W */ + 0x01010020 /* KEY_D */ + 0x01020021 /* KEY_F */ + 0x01030022 /* KEY_G */ + 0x01040023 /* KEY_H */ + 0x01050024 /* KEY_J */ + 0x01060025 /* KEY_K */ + 0x01070026 /* KEY_L */ + + 0x02000012 /* KEY_E */ + 0x02010034 /* KEY_DOT */ + 0x02020067 /* KEY_UP */ + 0x0203001c /* KEY_ENTER */ + 0x0205002c /* KEY_Z */ + 0x0206002d /* KEY_X */ + 0x0207002e /* KEY_C */ + 0x02080043 /* KEY_F9 */ + + 0x03000013 /* KEY_R */ + 0x0301002f /* KEY_V */ + 0x03020030 /* KEY_B */ + 0x03030031 /* KEY_N */ + 0x03040032 /* KEY_M */ + 0x03050039 /* KEY_SPACE */ + 0x03060039 /* KEY_SPACE */ + 0x03070069 /* KEY_LEFT */ + + 0x04000014 /* KEY_T */ + 0x0401006c /* KEY_DOWN */ + 0x0402006a /* KEY_RIGHT */ + 0x0404001d /* KEY_LEFTCTRL */ + 0x04050064 /* KEY_RIGHTALT */ + 0x0406002a /* KEY_LEFTSHIFT */ + 0x04080044 /* KEY_F10 */ + + 0x05000015 /* KEY_Y */ + 0x05080057 /* KEY_F11 */ + + 0x06000016 /* KEY_U */ + + 0x07000017 /* KEY_I */ + 0x07010041 /* KEY_F7 */ + 0x07020042 /* KEY_F8 */ + >; +}; + &twl_gpio { ti,pullups = <0x0>; ti,pulldowns = <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */ @@ -291,6 +351,13 @@ DVDD-supply = <&vio>; }; + tsl2563: tsl2563@29 { + compatible = "amstaos,tsl2563"; + reg = <0x29>; + + amstaos,cover-comp-gain = <16>; + }; + lp5523: lp5523@32 { compatible = "national,lp5523"; reg = <0x32>; @@ -356,6 +423,29 @@ compatible = "ti,bq27200"; reg = <0x55>; }; + + tpa6130a2: tpa6130a2@60 { + compatible = "ti,tpa6130a2"; + reg = <0x60>; + + Vdd-supply = <&vmmc2>; + + power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* 98 */ + }; + + bq24150a: bq24150a@6b { + compatible = "ti,bq24150a"; + reg = <0x6b>; + + ti,current-limit = <100>; + ti,weak-battery-voltage = <3400>; + ti,battery-regulation-voltage = <4200>; + ti,charge-current = <650>; + ti,termination-current = <100>; + ti,resistor-sense = <68>; + + ti,usb-charger-detection = <&isp1704>; + }; }; &i2c3 { diff --git a/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi b/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi new file mode 100644 index 000000000000..19d64864a109 --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-alto35-common.dtsi @@ -0,0 +1,77 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Alto35 expansion board is manufactured by Gumstix Inc. + */ + +#include "omap3-overo-common-peripherals.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + gpio148 { + label = "overo:red:gpio148"; + gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>; /* gpio 148 */ + }; + gpio150 { + label = "overo:yellow:gpio150"; + gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; /* gpio 150 */ + }; + gpio151 { + label = "overo:blue:gpio151"; + gpios = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* gpio 151 */ + }; + gpio170 { + label = "overo:green:gpio170"; + gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>; /* gpio 170 */ + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&button_pins>; + button0@10 { + label = "button0"; + linux,code = <BTN_0>; + gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; /* gpio_10 */ + gpio-key,wakeup; + }; + }; +}; + +&omap3_pmx_core { + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE4) /* uart1_tx.gpio_148 */ + OMAP3_CORE1_IOPAD(0x2180, PIN_OUTPUT | MUX_MODE4) /* uart1_cts.gpio_150 */ + OMAP3_CORE1_IOPAD(0x2182, PIN_OUTPUT | MUX_MODE4) /* uart1_rx.gpio_151 */ + OMAP3_CORE1_IOPAD(0x21c6, PIN_OUTPUT | MUX_MODE4) /* hdq_sio.gpio_170 */ + >; + }; +}; + +&omap3_pmx_wkup { + button_pins: pinmux_button_pins { + pinctrl-single,pins = < + OMAP3_WKUP_IOPAD(0x2a18, PIN_INPUT | MUX_MODE4) /* sys_clkout1.gpio_10 */ + >; + }; +}; + +&usbhshost { + status = "disabled"; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-alto35.dts b/arch/arm/boot/dts/omap3-overo-alto35.dts new file mode 100644 index 000000000000..a3249eb7501d --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-alto35.dts @@ -0,0 +1,22 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Alto35 expansion board is manufactured by Gumstix Inc. + */ + +/dts-v1/; + +#include "omap3-overo.dtsi" +#include "omap3-overo-alto35-common.dtsi" + +/ { + model = "OMAP35xx Gumstix Overo on Alto35"; + compatible = "gumstix,omap3-overo-alto35", "gumstix,omap3-overo", "ti,omap3430", "ti,omap3"; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-base.dtsi b/arch/arm/boot/dts/omap3-overo-base.dtsi new file mode 100644 index 000000000000..d36bf0250a05 --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-base.dtsi @@ -0,0 +1,221 @@ +/* + * Copyright (C) 2012 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * The Gumstix Overo must be combined with an expansion board. + */ + +/ { + pwmleds { + compatible = "pwm-leds"; + + overo { + label = "overo:blue:COM"; + pwms = <&twl_pwmled 1 7812500>; + max-brightness = <127>; + linux,default-trigger = "mmc0"; + }; + }; + + sound { + compatible = "ti,omap-twl4030"; + ti,model = "overo"; + + ti,mcbsp = <&mcbsp2>; + ti,codec = <&twl_audio>; + }; + + /* HS USB Port 2 Power */ + hsusb2_power: hsusb2_power_reg { + compatible = "regulator-fixed"; + regulator-name = "hsusb2_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio6 8 0>; /* gpio_168: vbus enable */ + startup-delay-us = <70000>; + enable-active-high; + }; + + /* HS USB Host PHY on PORT 2 */ + hsusb2_phy: hsusb2_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio6 23 GPIO_ACTIVE_LOW>; /* gpio_183 */ + vcc-supply = <&hsusb2_power>; + }; + + /* Regulator to trigger the nPoweron signal of the Wifi module */ + w3cbw003c_npoweron: regulator-w3cbw003c-npoweron { + compatible = "regulator-fixed"; + regulator-name = "regulator-w3cbw003c-npoweron"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* gpio_54: nPoweron */ + enable-active-high; + }; + + /* Regulator to trigger the nReset signal of the Wifi module */ + w3cbw003c_wifi_nreset: regulator-w3cbw003c-wifi-nreset { + pinctrl-names = "default"; + pinctrl-0 = <&w3cbw003c_pins &w3cbw003c_2_pins>; + compatible = "regulator-fixed"; + regulator-name = "regulator-w3cbw003c-wifi-nreset"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio1 16 GPIO_ACTIVE_HIGH>; /* gpio_16: WiFi nReset */ + startup-delay-us = <10000>; + }; + + /* Regulator to trigger the nReset signal of the Bluetooth module */ + w3cbw003c_bt_nreset: regulator-w3cbw003c-bt-nreset { + compatible = "regulator-fixed"; + regulator-name = "regulator-w3cbw003c-bt-nreset"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* gpio_164: BT nReset */ + startup-delay-us = <10000>; + }; +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusb2_pins + >; + + uart2_pins: pinmux_uart2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x216c, PIN_INPUT | MUX_MODE1) /* mcbsp3_dx.uart2_cts */ + OMAP3_CORE1_IOPAD(0x216e, PIN_OUTPUT | MUX_MODE1) /* mcbsp3_dr.uart2_rts */ + OMAP3_CORE1_IOPAD(0x2170, PIN_OUTPUT | MUX_MODE1) /* mcbsp3_clk.uart2_tx */ + OMAP3_CORE1_IOPAD(0x2172, PIN_INPUT | MUX_MODE1) /* mcbsp3_fsx.uart2_rx */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */ + OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + >; + }; + + mmc2_pins: pinmux_mmc2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */ + OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */ + OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */ + OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */ + OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */ + OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */ + >; + }; + + /* WiFi/BT combo */ + w3cbw003c_pins: pinmux_w3cbw003c_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20b4, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs3.gpio_54 */ + OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4) /* uart3_rts_sd.gpio_164 */ + >; + }; + + hsusb2_pins: pinmux_hsusb2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */ + OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */ + OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */ + OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */ + OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */ + OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */ + OMAP3_CORE1_IOPAD(0x21be, PIN_OUTPUT | MUX_MODE4) /* i2c2_scl.gpio_168 */ + OMAP3_CORE1_IOPAD(0x21c0, PIN_OUTPUT | MUX_MODE4) /* i2c2_sda.gpio_183 */ + >; + }; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + clock-frequency = <2600000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <7>; /* SYS_NIRQ cascaded to intc */ + interrupt-parent = <&intc>; + + twl_audio: audio { + compatible = "ti,twl4030-audio"; + codec { + }; + }; + }; +}; + +#include "twl4030.dtsi" +#include "twl4030_omap3.dtsi" + +/* i2c2 pins are used for gpio */ +&i2c2 { + status = "disabled"; +}; + +/* on board microSD slot */ +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + vmmc-supply = <&vmmc1>; + bus-width = <4>; +}; + +/* optional on board WiFi */ +&mmc2 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + vmmc-supply = <&w3cbw003c_npoweron>; + vqmmc-supply = <&w3cbw003c_bt_nreset>; + vmmc_aux-supply = <&w3cbw003c_wifi_nreset>; + bus-width = <4>; + cap-sdio-irq; + non-removable; +}; + +&twl_gpio { + ti,use-leds; +}; + +&usb_otg_hs { + interface-type = <0>; + usb-phy = <&usb2_phy>; + phys = <&usb2_phy>; + phy-names = "usb2-phy"; + mode = <3>; + power = <50>; +}; + +&usbhshost { + port2-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <0 &hsusb2_phy>; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&uart2_pins>; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi b/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi new file mode 100644 index 000000000000..19de6ff79686 --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-chestnut43-common.dtsi @@ -0,0 +1,69 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Chestnut43 expansion board is manufactured by Gumstix Inc. + */ + +#include "omap3-overo-common-peripherals.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + heartbeat { + label = "overo:red:gpio21"; + gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; /* gpio_21 */ + linux,default-trigger = "heartbeat"; + }; + gpio22 { + label = "overo:blue:gpio22"; + gpios = <&gpio1 22 GPIO_ACTIVE_LOW>; /* gpio_22 */ + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&button_pins>; + #address-cells = <1>; + #size-cells = <0>; + button0@23 { + label = "button0"; + linux,code = <BTN_0>; + gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; /* gpio_23 */ + gpio-key,wakeup; + }; + button1@14 { + label = "button1"; + linux,code = <BTN_1>; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; /* gpio_14 */ + gpio-key,wakeup; + }; + }; +}; + +#include "omap-gpmc-smsc9221.dtsi" + +&gpmc { + ranges = <5 0 0x2c000000 0x1000000>; /* CS5 */ + + ethernet@gpmc { + reg = <5 0 0xff>; + interrupt-parent = <&gpio6>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; /* GPIO 176 */ + }; +}; + +&lis33de { + status = "disabled"; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-chestnut43.dts b/arch/arm/boot/dts/omap3-overo-chestnut43.dts new file mode 100644 index 000000000000..fe0824aca3c0 --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-chestnut43.dts @@ -0,0 +1,38 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Chestnut43 expansion board is manufactured by Gumstix Inc. + */ + +/dts-v1/; + +#include "omap3-overo.dtsi" +#include "omap3-overo-chestnut43-common.dtsi" + +/ { + model = "OMAP35xx Gumstix Overo on Chestnut43"; + compatible = "gumstix,omap3-overo-chestnut43", "gumstix,omap3-overo", "ti,omap3430", "ti,omap3"; +}; + +&omap3_pmx_core2 { + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4) /* etk_d7.gpio_21 */ + OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4) /* etk_d8.gpio_22 */ + >; + }; + + button_pins: pinmux_button_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4) /* etk_d9.gpio_23 */ + OMAP3430_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4) /* etk_d0.gpio_14 */ + >; + }; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-common-peripherals.dtsi b/arch/arm/boot/dts/omap3-overo-common-peripherals.dtsi new file mode 100644 index 000000000000..5831bcc52966 --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-common-peripherals.dtsi @@ -0,0 +1,94 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Peripherals common to all Gumstix Overo boards (Tobi, Summit, Palo43,...) + */ + +/ { + lis33_3v3: lis33-3v3-reg { + compatible = "regulator-fixed"; + regulator-name = "lis33-3v3-reg"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + lis33_1v8: lis33-1v8-reg { + compatible = "regulator-fixed"; + regulator-name = "lis33-1v8-reg"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; +}; + +&omap3_pmx_core { + i2c3_pins: pinmux_i2c3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl.i2c3_scl */ + OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda.i2c3_sda */ + >; + }; + + uart3_pins: pinmux_uart3_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + >; + }; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; + clock-frequency = <100000>; + + /* optional 1K EEPROM with revision information */ + eeprom@51 { + compatible = "atmel,24c01"; + reg = <0x51>; + pagesize = <8>; + }; + + lis33de: lis33de@1d { + compatible = "st,lis33de", "st,lis3lv02d"; + reg = <0x1d>; + Vdd-supply = <&lis33_1v8>; + Vdd_IO-supply = <&lis33_3v3>; + + st,click-single-x; + st,click-single-y; + st,click-single-z; + st,click-thresh-x = <10>; + st,click-thresh-y = <10>; + st,click-thresh-z = <10>; + st,irq1-click; + st,irq2-click; + st,wakeup-x-lo; + st,wakeup-x-hi; + st,wakeup-y-lo; + st,wakeup-y-hi; + st,wakeup-z-lo; + st,wakeup-z-hi; + st,min-limit-x = <120>; + st,min-limit-y = <120>; + st,min-limit-z = <140>; + st,max-limit-x = <550>; + st,max-limit-y = <550>; + st,max-limit-z = <750>; + }; +}; + +&mmc3 { + status = "disabled"; +}; + +&uart3 { + pinctrl-names = "default"; + pinctrl-0 = <&uart3_pins>; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi b/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi new file mode 100644 index 000000000000..5e848c26986b --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-gallop43-common.dtsi @@ -0,0 +1,57 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Gallop43 expansion board is manufactured by Gumstix Inc. + */ + +#include "omap3-overo-common-peripherals.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + heartbeat { + label = "overo:red:gpio21"; + gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; /* gpio_21 */ + linux,default-trigger = "heartbeat"; + }; + gpio22 { + label = "overo:blue:gpio22"; + gpios = <&gpio1 22 GPIO_ACTIVE_LOW>; /* gpio_22 */ + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&button_pins>; + #address-cells = <1>; + #size-cells = <0>; + button0@23 { + label = "button0"; + linux,code = <BTN_0>; + gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; /* gpio_23 */ + gpio-key,wakeup; + }; + button1@14 { + label = "button1"; + linux,code = <BTN_1>; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; /* gpio_14 */ + gpio-key,wakeup; + }; + }; +}; + +&usbhshost { + status = "disabled"; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-gallop43.dts b/arch/arm/boot/dts/omap3-overo-gallop43.dts new file mode 100644 index 000000000000..241f5c1914e0 --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-gallop43.dts @@ -0,0 +1,38 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Gallop43 expansion board is manufactured by Gumstix Inc. + */ + +/dts-v1/; + +#include "omap3-overo.dtsi" +#include "omap3-overo-gallop43-common.dtsi" + +/ { + model = "OMAP35xx Gumstix Overo on Gallop43"; + compatible = "gumstix,omap3-overo-gallop43", "gumstix,omap3-overo", "ti,omap3430", "ti,omap3"; +}; + +&omap3_pmx_core2 { + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4) /* etk_d7.gpio_21 */ + OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4) /* etk_d8.gpio_22 */ + >; + }; + + button_pins: pinmux_button_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4) /* etk_d9.gpio_23 */ + OMAP3430_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4) /* etk_d0.gpio_14 */ + >; + }; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi b/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi new file mode 100644 index 000000000000..abea232825b9 --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-palo43-common.dtsi @@ -0,0 +1,53 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Palo43 expansion board is manufactured by Gumstix Inc. + */ + +#include "omap3-overo-common-peripherals.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + heartbeat { + label = "overo:red:gpio21"; + gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; /* gpio_21 */ + linux,default-trigger = "heartbeat"; + }; + gpio22 { + label = "overo:blue:gpio22"; + gpios = <&gpio1 22 GPIO_ACTIVE_LOW>; /* gpio_22 */ + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + pinctrl-names = "default"; + pinctrl-0 = <&button_pins>; + #address-cells = <1>; + #size-cells = <0>; + button0@23 { + label = "button0"; + linux,code = <BTN_0>; + gpios = <&gpio1 23 GPIO_ACTIVE_LOW>; /* gpio_23 */ + gpio-key,wakeup; + }; + button1@14 { + label = "button1"; + linux,code = <BTN_1>; + gpios = <&gpio1 14 GPIO_ACTIVE_LOW>; /* gpio_14 */ + gpio-key,wakeup; + }; + }; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-palo43.dts b/arch/arm/boot/dts/omap3-overo-palo43.dts new file mode 100644 index 000000000000..cedb103b4b66 --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-palo43.dts @@ -0,0 +1,38 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Palo43 expansion board is manufactured by Gumstix Inc. + */ + +/dts-v1/; + +#include "omap3-overo.dtsi" +#include "omap3-overo-palo43-common.dtsi" + +/ { + model = "OMAP35xx Gumstix Overo on Palo43"; + compatible = "gumstix,omap3-overo-palo43", "gumstix,omap3-overo", "ti,omap3430", "ti,omap3"; +}; + +&omap3_pmx_core2 { + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4) /* etk_d7.gpio_21 */ + OMAP3430_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4) /* etk_d8.gpio_22 */ + >; + }; + + button_pins: pinmux_button_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4) /* etk_d9.gpio_23 */ + OMAP3430_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4) /* etk_d0.gpio_14 */ + >; + }; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-storm-alto35.dts b/arch/arm/boot/dts/omap3-overo-storm-alto35.dts new file mode 100644 index 000000000000..e9cae52afc25 --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-storm-alto35.dts @@ -0,0 +1,21 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Alto35 expansion board is manufactured by Gumstix Inc. + */ + +/dts-v1/; + +#include "omap3-overo-storm.dtsi" +#include "omap3-overo-alto35-common.dtsi" + +/ { + model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Alto35"; + compatible = "gumstix,omap3-overo-alto35", "gumstix,omap3-overo", "ti,omap36xx", "ti,omap3"; +}; diff --git a/arch/arm/boot/dts/omap3-overo-storm-chestnut43.dts b/arch/arm/boot/dts/omap3-overo-storm-chestnut43.dts new file mode 100644 index 000000000000..7d82fdfd9909 --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-storm-chestnut43.dts @@ -0,0 +1,38 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Chestnut43 expansion board is manufactured by Gumstix Inc. + */ + +/dts-v1/; + +#include "omap3-overo-storm.dtsi" +#include "omap3-overo-chestnut43-common.dtsi" + +/ { + model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Chestnut43"; + compatible = "gumstix,omap3-overo-chestnut43", "gumstix,omap3-overo", "ti,omap36xx", "ti,omap3"; +}; + +&omap3_pmx_core2 { + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4) /* etk_d7.gpio_21 */ + OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4) /* etk_d8.gpio_22 */ + >; + }; + + button_pins: pinmux_button_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4) /* etk_d9.gpio_23 */ + OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4) /* etk_d0.gpio_14 */ + >; + }; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-storm-gallop43.dts b/arch/arm/boot/dts/omap3-overo-storm-gallop43.dts new file mode 100644 index 000000000000..a1b57e0cf37f --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-storm-gallop43.dts @@ -0,0 +1,38 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Gallop43 expansion board is manufactured by Gumstix Inc. + */ + +/dts-v1/; + +#include "omap3-overo-storm.dtsi" +#include "omap3-overo-gallop43-common.dtsi" + +/ { + model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Gallop43"; + compatible = "gumstix,omap3-overo-gallop43", "gumstix,omap3-overo", "ti,omap36xx", "ti,omap3"; +}; + +&omap3_pmx_core2 { + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4) /* etk_d7.gpio_21 */ + OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4) /* etk_d8.gpio_22 */ + >; + }; + + button_pins: pinmux_button_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4) /* etk_d9.gpio_23 */ + OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4) /* etk_d0.gpio_14 */ + >; + }; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-storm-palo43.dts b/arch/arm/boot/dts/omap3-overo-storm-palo43.dts new file mode 100644 index 000000000000..b585d8fbc347 --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-storm-palo43.dts @@ -0,0 +1,38 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Palo43 expansion board is manufactured by Gumstix Inc. + */ + +/dts-v1/; + +#include "omap3-overo-storm.dtsi" +#include "omap3-overo-palo43-common.dtsi" + +/ { + model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Palo43"; + compatible = "gumstix,omap3-overo-palo43", "gumstix,omap3-overo", "ti,omap36xx", "ti,omap3"; +}; + +&omap3_pmx_core2 { + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4) /* etk_d7.gpio_21 */ + OMAP3630_CORE2_IOPAD(0x25ec, PIN_OUTPUT | MUX_MODE4) /* etk_d8.gpio_22 */ + >; + }; + + button_pins: pinmux_button_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25ee, PIN_INPUT | MUX_MODE4) /* etk_d9.gpio_23 */ + OMAP3630_CORE2_IOPAD(0x25dc, PIN_INPUT | MUX_MODE4) /* etk_d0.gpio_14 */ + >; + }; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-storm-summit.dts b/arch/arm/boot/dts/omap3-overo-storm-summit.dts new file mode 100644 index 000000000000..a0d7fd8369d7 --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-storm-summit.dts @@ -0,0 +1,30 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Summit expansion board is manufactured by Gumstix Inc. + */ + +/dts-v1/; + +#include "omap3-overo-storm.dtsi" +#include "omap3-overo-summit-common.dtsi" + +/ { + model = "OMAP36xx/AM37xx/DM37xx Gumstix Overo on Summit"; + compatible = "gumstix,omap3-overo-summit", "gumstix,omap3-overo", "ti,omap36xx", "ti,omap3"; +}; + +&omap3_pmx_core2 { + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4) /* etk_d7.gpio_21 */ + >; + }; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-storm-tobi.dts b/arch/arm/boot/dts/omap3-overo-storm-tobi.dts index 966b5c9cd96a..879383acad87 100644 --- a/arch/arm/boot/dts/omap3-overo-storm-tobi.dts +++ b/arch/arm/boot/dts/omap3-overo-storm-tobi.dts @@ -12,7 +12,7 @@ /dts-v1/; -#include "omap36xx.dtsi" +#include "omap3-overo-storm.dtsi" #include "omap3-overo-tobi-common.dtsi" / { diff --git a/arch/arm/boot/dts/omap3-overo-storm.dtsi b/arch/arm/boot/dts/omap3-overo-storm.dtsi new file mode 100644 index 000000000000..6cb418b4124a --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-storm.dtsi @@ -0,0 +1,35 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "omap36xx.dtsi" +#include "omap3-overo-base.dtsi" + +&omap3_pmx_core2 { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusb2_2_pins + >; + + hsusb2_2_pins: pinmux_hsusb2_2_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + >; + }; + + w3cbw003c_2_pins: pinmux_w3cbw003c_2_pins { + pinctrl-single,pins = < + OMAP3630_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */ + >; + }; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-summit-common.dtsi b/arch/arm/boot/dts/omap3-overo-summit-common.dtsi new file mode 100644 index 000000000000..999d1cd4a09f --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-summit-common.dtsi @@ -0,0 +1,31 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Summit expansion board is manufactured by Gumstix Inc. + */ + +#include "omap3-overo-common-peripherals.dtsi" + +/ { + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins>; + heartbeat { + label = "overo:red:gpio21"; + gpios = <&gpio1 21 GPIO_ACTIVE_LOW>; /* gpio_21 */ + linux,default-trigger = "heartbeat"; + }; + }; +}; + +&lis33de { + status = "disabled"; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-summit.dts b/arch/arm/boot/dts/omap3-overo-summit.dts new file mode 100644 index 000000000000..69765609455a --- /dev/null +++ b/arch/arm/boot/dts/omap3-overo-summit.dts @@ -0,0 +1,30 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/* + * Summit expansion board is manufactured by Gumstix Inc. + */ + +/dts-v1/; + +#include "omap3-overo.dtsi" +#include "omap3-overo-summit-common.dtsi" + +/ { + model = "OMAP35xx Gumstix Overo on Summit"; + compatible = "gumstix,omap3-overo-summit", "gumstix,omap3-overo", "ti,omap3430", "ti,omap3"; +}; + +&omap3_pmx_core2 { + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25ea, PIN_OUTPUT | MUX_MODE4) /* etk_d7.gpio_21 */ + >; + }; +}; + diff --git a/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi b/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi index 4edc013a91c1..13df50b39442 100644 --- a/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi +++ b/arch/arm/boot/dts/omap3-overo-tobi-common.dtsi @@ -10,7 +10,7 @@ * Tobi expansion board is manufactured by Gumstix Inc. */ -#include "omap3-overo.dtsi" +#include "omap3-overo-common-peripherals.dtsi" / { leds { @@ -21,60 +21,21 @@ linux,default-trigger = "heartbeat"; }; }; - - vddvario: regulator-vddvario { - compatible = "regulator-fixed"; - regulator-name = "vddvario"; - regulator-always-on; - }; - - vdd33a: regulator-vdd33a { - compatible = "regulator-fixed"; - regulator-name = "vdd33a"; - regulator-always-on; - }; }; +#include "omap-gpmc-smsc9221.dtsi" + &gpmc { ranges = <5 0 0x2c000000 0x1000000>; /* CS5 */ - ethernet@5,0 { - compatible = "smsc,lan9221", "smsc,lan9115"; + ethernet@gpmc { reg = <5 0 0xff>; - bank-width = <2>; - - gpmc,mux-add-data; - gpmc,cs-on-ns = <0>; - gpmc,cs-rd-off-ns = <42>; - gpmc,cs-wr-off-ns = <36>; - gpmc,adv-on-ns = <6>; - gpmc,adv-rd-off-ns = <12>; - gpmc,adv-wr-off-ns = <12>; - gpmc,oe-on-ns = <0>; - gpmc,oe-off-ns = <42>; - gpmc,we-on-ns = <0>; - gpmc,we-off-ns = <36>; - gpmc,rd-cycle-ns = <60>; - gpmc,wr-cycle-ns = <54>; - gpmc,access-ns = <36>; - gpmc,page-burst-access-ns = <0>; - gpmc,bus-turnaround-ns = <0>; - gpmc,cycle2cycle-delay-ns = <0>; - gpmc,wr-data-mux-bus-ns = <18>; - gpmc,wr-access-ns = <42>; - gpmc,cycle2cycle-samecsen; - gpmc,cycle2cycle-diffcsen; - interrupt-parent = <&gpio6>; interrupts = <16 IRQ_TYPE_LEVEL_LOW>; /* GPIO 176 */ - reg-io-width = <4>; }; }; -&i2c3 { - clock-frequency = <100000>; -}; - -&mmc3 { +&lis33de { status = "disabled"; }; + diff --git a/arch/arm/boot/dts/omap3-overo-tobi.dts b/arch/arm/boot/dts/omap3-overo-tobi.dts index de5653e1b5ca..fd6400efcdee 100644 --- a/arch/arm/boot/dts/omap3-overo-tobi.dts +++ b/arch/arm/boot/dts/omap3-overo-tobi.dts @@ -12,7 +12,7 @@ /dts-v1/; -#include "omap34xx.dtsi" +#include "omap3-overo.dtsi" #include "omap3-overo-tobi-common.dtsi" / { diff --git a/arch/arm/boot/dts/omap3-overo.dtsi b/arch/arm/boot/dts/omap3-overo.dtsi index 597099907f8e..69ca7c45bca2 100644 --- a/arch/arm/boot/dts/omap3-overo.dtsi +++ b/arch/arm/boot/dts/omap3-overo.dtsi @@ -1,94 +1,38 @@ /* - * Copyright (C) 2012 Florian Vaussard, EPFL Mobots group + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -/* - * The Gumstix Overo must be combined with an expansion board. - */ +#include "omap34xx.dtsi" +#include "omap3-overo-base.dtsi" -/ { - pwmleds { - compatible = "pwm-leds"; - - overo { - label = "overo:blue:COM"; - pwms = <&twl_pwmled 1 7812500>; - max-brightness = <127>; - linux,default-trigger = "mmc0"; - }; - }; - - sound { - compatible = "ti,omap-twl4030"; - ti,model = "overo"; - - ti,mcbsp = <&mcbsp2>; - ti,codec = <&twl_audio>; - }; -}; - -&i2c1 { - clock-frequency = <2600000>; - - twl: twl@48 { - reg = <0x48>; - interrupts = <7>; /* SYS_NIRQ cascaded to intc */ - interrupt-parent = <&intc>; +&omap3_pmx_core2 { + pinctrl-names = "default"; + pinctrl-0 = < + &hsusb2_2_pins + >; - twl_audio: audio { - compatible = "ti,twl4030-audio"; - codec { - }; - }; + hsusb2_2_pins: pinmux_hsusb2_2_pins { + pinctrl-single,pins = < + OMAP3430_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */ + OMAP3430_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */ + OMAP3430_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */ + OMAP3430_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */ + OMAP3430_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */ + OMAP3430_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */ + >; }; -}; - -#include "twl4030.dtsi" -#include "twl4030_omap3.dtsi" - -/* i2c2 pins are used for gpio */ -&i2c2 { - status = "disabled"; -}; -/* on board microSD slot */ -&mmc1 { - vmmc-supply = <&vmmc1>; - bus-width = <4>; -}; - -/* optional on board WiFi */ -&mmc2 { - bus-width = <4>; -}; - -&twl_gpio { - ti,use-leds; -}; - -&usb_otg_hs { - interface-type = <0>; - usb-phy = <&usb2_phy>; - phys = <&usb2_phy>; - phy-names = "usb2-phy"; - mode = <3>; - power = <50>; -}; - -&omap3_pmx_core { - uart3_pins: pinmux_uart3_pins { + w3cbw003c_2_pins: pinmux_w3cbw003c_2_pins { pinctrl-single,pins = < - 0x16e (PIN_INPUT | PIN_OFF_WAKEUPENABLE | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ - 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ + OMAP3430_CORE2_IOPAD(0x25e0, PIN_OUTPUT | MUX_MODE4) /* etk_d2.gpio_16 */ >; }; }; -&uart3 { - pinctrl-names = "default"; - pinctrl-0 = <&uart3_pins>; +&mcbsp2 { + status = "okay"; }; diff --git a/arch/arm/boot/dts/omap3-sb-t35.dtsi b/arch/arm/boot/dts/omap3-sb-t35.dtsi index b9a2fedce7ee..7909c51b05a5 100644 --- a/arch/arm/boot/dts/omap3-sb-t35.dtsi +++ b/arch/arm/boot/dts/omap3-sb-t35.dtsi @@ -2,11 +2,36 @@ * Common support for CompuLab SB-T35 used on SBC-T3530, SBC-T3517 and SBC-T3730 */ +/ { + vddvario_sb_t35: regulator-vddvario-sb-t35 { + compatible = "regulator-fixed"; + regulator-name = "vddvario"; + regulator-always-on; + }; + + vdd33a_sb_t35: regulator-vdd33a-sb-t35 { + compatible = "regulator-fixed"; + regulator-name = "vdd33a"; + regulator-always-on; + }; +}; + +&omap3_pmx_core { + smsc2_pins: pinmux_smsc2_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20b6, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs4.gpmc_ncs4 */ + OMAP3_CORE1_IOPAD(0x20d2, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_wait3.gpio_65 */ + >; + }; +}; + &gpmc { ranges = <4 0 0x2d000000 0x01000000>; smsc2: ethernet@4,0 { compatible = "smsc,lan9221", "smsc,lan9115"; + pinctrl-names = "default"; + pinctrl-0 = <&smsc2_pins>; interrupt-parent = <&gpio3>; interrupts = <1 IRQ_TYPE_LEVEL_LOW>; reg = <4 0 0xff>; @@ -32,8 +57,8 @@ gpmc,wr-access-ns = <186>; gpmc,cycle2cycle-samecsen; gpmc,cycle2cycle-diffcsen; - vddvario-supply = <&vddvario>; - vdd33a-supply = <&vdd33a>; + vddvario-supply = <&vddvario_sb_t35>; + vdd33a-supply = <&vdd33a_sb_t35>; reg-io-width = <4>; smsc,save-mac-address; }; diff --git a/arch/arm/boot/dts/omap3-sbc-t3517.dts b/arch/arm/boot/dts/omap3-sbc-t3517.dts new file mode 100644 index 000000000000..024c9c6c682d --- /dev/null +++ b/arch/arm/boot/dts/omap3-sbc-t3517.dts @@ -0,0 +1,43 @@ +/* + * Suppport for CompuLab SBC-T3517 with CM-T3517 + */ + +#include "omap3-cm-t3517.dts" +#include "omap3-sb-t35.dtsi" + +/ { + model = "CompuLab SBC-T3517 with CM-T3517"; + compatible = "compulab,omap3-sbc-t3517", "compulab,omap3-cm-t3517", "ti,am3517", "ti,omap3"; +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &sb_t35_usb_hub_pins + &usb_hub_pins + >; + + mmc1_aux_pins: pinmux_mmc1_aux_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x20c0, PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_clk.gpio_59 */ + OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE4) /* uart2_cts.gpio_144 */ + >; + }; + + sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x21ec, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_98 - SB-T35 USB HUB RST */ + >; + }; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = < + &mmc1_pins + &mmc1_aux_pins + >; + + wp-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>; /* gpio_59 */ + cd-gpios = <&gpio5 16 GPIO_ACTIVE_HIGH>; /* gpio_144 */ +}; diff --git a/arch/arm/boot/dts/omap3-sbc-t3530.dts b/arch/arm/boot/dts/omap3-sbc-t3530.dts new file mode 100644 index 000000000000..bbbeea6b1988 --- /dev/null +++ b/arch/arm/boot/dts/omap3-sbc-t3530.dts @@ -0,0 +1,36 @@ +/* + * Suppport for CompuLab SBC-T3530 with CM-T3530 + */ + +#include "omap3-cm-t3530.dts" +#include "omap3-sb-t35.dtsi" + +/ { + model = "CompuLab SBC-T3530 with CM-T3530"; + compatible = "compulab,omap3-sbc-t3530", "compulab,omap3-cm-t3530", "ti,omap34xx", "ti,omap3"; +}; + +&omap3_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = <&sb_t35_usb_hub_pins>; + + sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins { + pinctrl-single,pins = < + OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */ + >; + }; +}; + +/* + * The following ranges correspond to SMSC9x eth chips on CM-T3530 CoM and + * SB-T35 baseboard respectively. + * This setting includes both chips in SBC-T3530 board device tree. + */ +&gpmc { + ranges = <5 0 0x2c000000 0x01000000>, + <4 0 0x2d000000 0x01000000>; +}; + +&mmc1 { + cd-gpios = <&twl_gpio 0 GPIO_ACTIVE_HIGH>; +}; diff --git a/arch/arm/boot/dts/omap3-sbc-t3730.dts b/arch/arm/boot/dts/omap3-sbc-t3730.dts index c119bd545053..08e4a7086f22 100644 --- a/arch/arm/boot/dts/omap3-sbc-t3730.dts +++ b/arch/arm/boot/dts/omap3-sbc-t3730.dts @@ -10,21 +10,18 @@ compatible = "compulab,omap3-sbc-t3730", "compulab,omap3-cm-t3730", "ti,omap36xx", "ti,omap3"; }; -&gpmc { - ranges = <5 0 0x2c000000 0x01000000>, - <4 0 0x2d000000 0x01000000>; -}; - -&smsc2 { +&omap3_pmx_core { pinctrl-names = "default"; - pinctrl-0 = <&smsc2_pins>; -}; + pinctrl-0 = <&sb_t35_usb_hub_pins>; -&omap3_pmx_core { - smsc2_pins: pinmux_smsc2_pins { + sb_t35_usb_hub_pins: pinmux_sb_t35_usb_hub_pins { pinctrl-single,pins = < - 0x86 (PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs4.gpmc_ncs4 */ - 0xa2 (PIN_INPUT_PULLUP | MUX_MODE4) /* gpmc_wait3.gpio_65 */ + OMAP3_CORE1_IOPAD(0x2130, PIN_OUTPUT | MUX_MODE4) /* ccdc_wen.gpio_167 - SB-T35 USB HUB RST */ >; }; -}; \ No newline at end of file +}; + +&gpmc { + ranges = <5 0 0x2c000000 0x01000000>, + <4 0 0x2d000000 0x01000000>; +}; diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index a5fc83b9c835..a089e6e00457 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -35,6 +35,11 @@ compatible = "arm,cortex-a8"; device_type = "cpu"; reg = <0x0>; + + clocks = <&dpll1_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ }; }; @@ -411,10 +416,19 @@ }; mmu_isp: mmu@480bd400 { - compatible = "ti,omap3-mmu-isp"; - ti,hwmods = "mmu_isp"; + compatible = "ti,omap2-iommu"; reg = <0x480bd400 0x80>; - interrupts = <8>; + interrupts = <24>; + ti,hwmods = "mmu_isp"; + ti,#tlb-entries = <8>; + }; + + mmu_iva: mmu@5d000000 { + compatible = "ti,omap2-iommu"; + reg = <0x5d000000 0x80>; + interrupts = <28>; + ti,hwmods = "mmu_iva"; + status = "disabled"; }; wdt2: wdt@48314000 { @@ -436,6 +450,7 @@ dmas = <&sdma 31>, <&sdma 32>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp2: mcbsp@49022000 { @@ -453,6 +468,7 @@ dmas = <&sdma 33>, <&sdma 34>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp3: mcbsp@49024000 { @@ -470,6 +486,7 @@ dmas = <&sdma 17>, <&sdma 18>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp4: mcbsp@49026000 { @@ -485,6 +502,7 @@ dmas = <&sdma 19>, <&sdma 20>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp5: mcbsp@48096000 { @@ -500,6 +518,7 @@ dmas = <&sdma 21>, <&sdma 22>; dma-names = "tx", "rx"; + status = "disabled"; }; sham: sham@480c3000 { @@ -634,14 +653,14 @@ ranges; usbhsohci: ohci@48064400 { - compatible = "ti,ohci-omap3", "usb-ohci"; + compatible = "ti,ohci-omap3"; reg = <0x48064400 0x400>; interrupt-parent = <&intc>; interrupts = <76>; }; usbhsehci: ehci@48064800 { - compatible = "ti,ehci-omap", "usb-ehci"; + compatible = "ti,ehci-omap"; reg = <0x48064800 0x400>; interrupt-parent = <&intc>; interrupts = <77>; diff --git a/arch/arm/boot/dts/omap3430-sdp.dts b/arch/arm/boot/dts/omap3430-sdp.dts index 281914ed0151..02f69f4a8fd3 100644 --- a/arch/arm/boot/dts/omap3430-sdp.dts +++ b/arch/arm/boot/dts/omap3430-sdp.dts @@ -34,6 +34,10 @@ &mmc1 { vmmc-supply = <&vmmc1>; vmmc_aux-supply = <&vsim>; + /* + * S6-3 must be in ON position for 8 bit mode to function + * Else, use 4 bit mode + */ bus-width = <8>; }; @@ -103,9 +107,8 @@ #address-cells = <1>; #size-cells = <1>; reg = <1 0 0x08000000>; + ti,nand-ecc-opt = "ham1"; nand-bus-width = <8>; - - ti,nand-ecc-opt = "sw"; gpmc,cs-on-ns = <0>; gpmc,cs-rd-off-ns = <36>; gpmc,cs-wr-off-ns = <36>; diff --git a/arch/arm/boot/dts/omap3430es1-clocks.dtsi b/arch/arm/boot/dts/omap3430es1-clocks.dtsi index 02f6c7fabbec..6f31954636a1 100644 --- a/arch/arm/boot/dts/omap3430es1-clocks.dtsi +++ b/arch/arm/boot/dts/omap3430es1-clocks.dtsi @@ -82,16 +82,16 @@ ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>; }; - ssi_ssr_fck_3430es1: ssi_ssr_fck_3430es1 { + ssi_ssr_fck: ssi_ssr_fck_3430es1 { #clock-cells = <0>; compatible = "ti,composite-clock"; clocks = <&ssi_ssr_gate_fck_3430es1>, <&ssi_ssr_div_fck_3430es1>; }; - ssi_sst_fck_3430es1: ssi_sst_fck_3430es1 { + ssi_sst_fck: ssi_sst_fck_3430es1 { #clock-cells = <0>; compatible = "fixed-factor-clock"; - clocks = <&ssi_ssr_fck_3430es1>; + clocks = <&ssi_ssr_fck>; clock-mult = <1>; clock-div = <2>; }; @@ -120,7 +120,7 @@ clock-div = <1>; }; - ssi_ick_3430es1: ssi_ick_3430es1 { + ssi_ick: ssi_ick_3430es1 { #clock-cells = <0>; compatible = "ti,omap3-no-wait-interface-clock"; clocks = <&ssi_l4_ick>; @@ -203,6 +203,6 @@ <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>, <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>, <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, - <&fshostusb_fck>, <&fac_ick>, <&ssi_ick_3430es1>; + <&fshostusb_fck>, <&fac_ick>, <&ssi_ick>; }; }; diff --git a/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi b/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi index 8ed475dd63c9..877318c28364 100644 --- a/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi +++ b/arch/arm/boot/dts/omap36xx-omap3430es2plus-clocks.dtsi @@ -25,16 +25,16 @@ ti,dividers = <0>, <1>, <2>, <3>, <4>, <0>, <6>, <0>, <8>; }; - ssi_ssr_fck_3430es2: ssi_ssr_fck_3430es2 { + ssi_ssr_fck: ssi_ssr_fck_3430es2 { #clock-cells = <0>; compatible = "ti,composite-clock"; clocks = <&ssi_ssr_gate_fck_3430es2>, <&ssi_ssr_div_fck_3430es2>; }; - ssi_sst_fck_3430es2: ssi_sst_fck_3430es2 { + ssi_sst_fck: ssi_sst_fck_3430es2 { #clock-cells = <0>; compatible = "fixed-factor-clock"; - clocks = <&ssi_ssr_fck_3430es2>; + clocks = <&ssi_ssr_fck>; clock-mult = <1>; clock-div = <2>; }; @@ -55,7 +55,7 @@ clock-div = <1>; }; - ssi_ick_3430es2: ssi_ick_3430es2 { + ssi_ick: ssi_ick_3430es2 { #clock-cells = <0>; compatible = "ti,omap3-ssi-interface-clock"; clocks = <&ssi_l4_ick>; @@ -193,6 +193,6 @@ <&i2c1_ick>, <&uart2_ick>, <&uart1_ick>, <&gpt11_ick>, <&gpt10_ick>, <&mcbsp5_ick>, <&mcbsp1_ick>, <&omapctrl_ick>, <&aes2_ick>, <&sha12_ick>, - <&ssi_ick_3430es2>; + <&ssi_ick>; }; }; diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi index 7e8dee9175d6..ba077cd95e4e 100644 --- a/arch/arm/boot/dts/omap36xx.dtsi +++ b/arch/arm/boot/dts/omap36xx.dtsi @@ -39,6 +39,26 @@ clock-frequency = <48000000>; }; + abb_mpu_iva: regulator-abb-mpu { + compatible = "ti,abb-v1"; + regulator-name = "abb_mpu_iva"; + #address-cell = <0>; + #size-cells = <0>; + reg = <0x483072f0 0x8>, <0x48306818 0x4>; + reg-names = "base-address", "int-address"; + ti,tranxdone-status-mask = <0x4000000>; + clocks = <&sys_ck>; + ti,settling-time = <30>; + ti,clock-cycles = <8>; + ti,abb_info = < + /*uV ABB efuse rbb_m fbb_m vset_m*/ + 1012500 0 0 0 0 0 + 1200000 0 0 0 0 0 + 1325000 0 0 0 0 0 + 1375000 1 0 0 0 0 + >; + }; + omap3_pmx_core2: pinmux@480025a0 { compatible = "ti,omap3-padconf", "pinctrl-single"; reg = <0x480025a0 0x5c>; diff --git a/arch/arm/boot/dts/omap4-duovero-parlor.dts b/arch/arm/boot/dts/omap4-duovero-parlor.dts new file mode 100644 index 000000000000..96f51d870812 --- /dev/null +++ b/arch/arm/boot/dts/omap4-duovero-parlor.dts @@ -0,0 +1,146 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +/dts-v1/; + +#include "omap4-duovero.dtsi" + +#include <dt-bindings/input/input.h> + +/ { + model = "OMAP4430 Gumstix Duovero on Parlor"; + compatible = "gumstix,omap4-duovero-parlor", "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4"; + + leds { + compatible = "gpio-leds"; + led0 { + label = "duovero:blue:led0"; + gpios = <&gpio4 26 GPIO_ACTIVE_HIGH>; /* gpio_122 */ + linux,default-trigger = "heartbeat"; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + button0@121 { + label = "button0"; + linux,code = <BTN_0>; + gpios = <&gpio4 25 GPIO_ACTIVE_LOW>; /* gpio_121 */ + gpio-key,wakeup; + }; + }; +}; + +&omap4_pmx_core { + pinctrl-0 = < + &led_pins + &button_pins + &smsc_pins + >; + + led_pins: pinmux_led_pins { + pinctrl-single,pins = < + 0xd6 (PIN_OUTPUT | MUX_MODE3) /* abe_dmic_din3.gpio_122 */ + >; + }; + + button_pins: pinmux_button_pins { + pinctrl-single,pins = < + 0xd4 (PIN_INPUT_PULLUP | MUX_MODE3) /* abe_dmic_din2.gpio_121 */ + >; + }; + + i2c2_pins: pinmux_i2c2_pins { + pinctrl-single,pins = < + 0xe6 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */ + 0xe8 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */ + >; + }; + + i2c3_pins: pinmux_i2c3_pins { + pinctrl-single,pins = < + 0xea (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ + 0xec (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ + >; + }; + + smsc_pins: pinmux_smsc_pins { + pinctrl-single,pins = < + 0x28 (PIN_INPUT | MUX_MODE3) /* gpmc_a20.gpio_44: IRQ */ + 0x2a (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a21.gpio_45: nReset */ + 0x30 (PIN_INPUT_PULLUP | MUX_MODE3) /* gpmc_a24.gpio_48: amdix enabled */ + >; + }; +}; + +&i2c2 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins>; + + clock-frequency = <400000>; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c3_pins>; + + clock-frequency = <100000>; + + /* optional 1K EEPROM with revision information */ + eeprom@51 { + compatible = "atmel,24c01"; + reg = <0x51>; + pagesize = <8>; + }; +}; + +&mmc3 { + status = "disabled"; +}; + +#include "omap-gpmc-smsc911x.dtsi" + +&gpmc { + ranges = <5 0 0x2c000000 0x1000000>; /* CS5 */ + + ethernet@gpmc { + reg = <5 0 0xff>; + interrupt-parent = <&gpio2>; + interrupts = <12 IRQ_TYPE_LEVEL_LOW>; /* gpio_44 */ + + phy-mode = "mii"; + + gpmc,cs-on-ns = <10>; + gpmc,cs-rd-off-ns = <50>; + gpmc,cs-wr-off-ns = <50>; + gpmc,adv-on-ns = <0>; + gpmc,adv-rd-off-ns = <10>; + gpmc,adv-wr-off-ns = <10>; + gpmc,oe-on-ns = <15>; + gpmc,oe-off-ns = <50>; + gpmc,we-on-ns = <15>; + gpmc,we-off-ns = <50>; + gpmc,rd-cycle-ns = <50>; + gpmc,wr-cycle-ns = <50>; + gpmc,access-ns = <50>; + gpmc,page-burst-access-ns = <0>; + gpmc,bus-turnaround-ns = <35>; + gpmc,cycle2cycle-delay-ns = <35>; + gpmc,wr-data-mux-bus-ns = <35>; + gpmc,wr-access-ns = <50>; + + gpmc,mux-add-data = <2>; + gpmc,sync-read; + gpmc,sync-write; + gpmc,clk-activation-ns = <5>; + gpmc,sync-clk-ps = <20000>; + }; +}; + + diff --git a/arch/arm/boot/dts/omap4-duovero.dtsi b/arch/arm/boot/dts/omap4-duovero.dtsi new file mode 100644 index 000000000000..a514791154eb --- /dev/null +++ b/arch/arm/boot/dts/omap4-duovero.dtsi @@ -0,0 +1,252 @@ +/* + * Copyright (C) 2014 Florian Vaussard, EPFL Mobots group + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include "omap443x.dtsi" + +/ { + model = "Gumstix Duovero"; + compatible = "gumstix,omap4-duovero", "ti,omap4430", "ti,omap4"; + + memory { + device_type = "memory"; + reg = <0x80000000 0x40000000>; /* 1 GB */ + }; + + sound { + compatible = "ti,abe-twl6040"; + ti,model = "DuoVero"; + + ti,mclk-freq = <38400000>; + + ti,mcpdm = <&mcpdm>; + + ti,twl6040 = <&twl6040>; + + /* Audio routing */ + ti,audio-routing = + "Headset Stereophone", "HSOL", + "Headset Stereophone", "HSOR", + "HSMIC", "Headset Mic", + "Headset Mic", "Headset Mic Bias"; + }; + + /* HS USB Host PHY on PORT 1 */ + hsusb1_phy: hsusb1_phy { + compatible = "usb-nop-xceiv"; + reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; /* gpio_62 */ + + pinctrl-names = "default"; + pinctrl-0 = <&hsusb1phy_pins>; + + clocks = <&auxclk3_ck>; + clock-names = "main_clk"; + clock-frequency = <19200000>; + }; + + /* regulator for w2cbw0015 on sdio5 */ + w2cbw0015_vmmc: w2cbw0015_vmmc { + pinctrl-names = "default"; + pinctrl-0 = <&w2cbw0015_pins>; + compatible = "regulator-fixed"; + regulator-name = "w2cbw0015"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + gpio = <&gpio2 11 GPIO_ACTIVE_LOW>; /* gpio_43 */ + startup-delay-us = <70000>; + enable-active-high; + regulator-boot-on; + }; +}; + +&omap4_pmx_core { + pinctrl-names = "default"; + pinctrl-0 = < + &twl6040_pins + &mcpdm_pins + &mcbsp1_pins + &hsusbb1_pins + >; + + twl6040_pins: pinmux_twl6040_pins { + pinctrl-single,pins = < + 0x126 (PIN_OUTPUT | MUX_MODE3) /* usbb2_ulpitll_nxt.gpio_160 */ + 0x160 (PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */ + >; + }; + + mcpdm_pins: pinmux_mcpdm_pins { + pinctrl-single,pins = < + 0xc6 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */ + 0xc8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */ + 0xca (PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */ + 0xcc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */ + 0xce (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ + >; + }; + + mcbsp1_pins: pinmux_mcbsp1_pins { + pinctrl-single,pins = < + 0xbe (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */ + 0xc0 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */ + 0xc2 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */ + 0xc4 (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */ + >; + }; + + hsusbb1_pins: pinmux_hsusbb1_pins { + pinctrl-single,pins = < + 0x82 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_clk.usbb1_ulpiphy_clk */ + 0x84 (PIN_OUTPUT | MUX_MODE4) /* usbb1_ulpitll_stp.usbb1_ulpiphy_stp */ + 0x86 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dir.usbb1_ulpiphy_dir */ + 0x88 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_nxt.usbb1_ulpiphy_nxt */ + 0x8a (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat0.usbb1_ulpiphy_dat0 */ + 0x8c (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat1.usbb1_ulpiphy_dat1 */ + 0x8e (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat2.usbb1_ulpiphy_dat2 */ + 0x90 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat3.usbb1_ulpiphy_dat3 */ + 0x92 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat4.usbb1_ulpiphy_dat4 */ + 0x94 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat5.usbb1_ulpiphy_dat5 */ + 0x96 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat6.usbb1_ulpiphy_dat6 */ + 0x98 (PIN_INPUT_PULLDOWN | MUX_MODE4) /* usbb1_ulpitll_dat7.usbb1_ulpiphy_dat7 */ + >; + }; + + hsusb1phy_pins: pinmux_hsusb1phy_pins { + pinctrl-single,pins = < + 0x4c (PIN_OUTPUT | MUX_MODE3) /* gpmc_wait1.gpio_62 */ + >; + }; + + w2cbw0015_pins: pinmux_w2cbw0015_pins { + pinctrl-single,pins = < + 0x26 (PIN_OUTPUT | MUX_MODE3) /* gpmc_a19.gpio_43 */ + 0x3a (PIN_INPUT | MUX_MODE3) /* gpmc_ncs3.gpio_53 */ + >; + }; + + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0xe2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + 0xe4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ + >; + }; + + i2c4_pins: pinmux_i2c4_pins { + pinctrl-single,pins = < + 0xee (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */ + 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ + >; + }; + + mmc1_pins: pinmux_mmc1_pins { + pinctrl-single,pins = < + 0xa2 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */ + 0xa4 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmcc1_cmd */ + 0xa6 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmcc1_dat0 */ + 0xa8 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */ + 0xaa (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */ + 0xac (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */ + >; + }; + + mmc5_pins: pinmux_mmc5_pins { + pinctrl-single,pins = < + 0x108 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_clk */ + 0x10a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmcc5_cmd */ + 0x10c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmcc5_dat0 */ + 0x10e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat1 */ + 0x110 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat2 */ + 0x112 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc5_dat3 */ + >; + }; +}; + +/* PMIC */ +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins>; + + clock-frequency = <400000>; + + twl: twl@48 { + reg = <0x48>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */ + interrupt-parent = <&gic>; + }; + + twl6040: twl@4b { + compatible = "ti,twl6040"; + reg = <0x4b>; + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */ + interrupt-parent = <&gic>; + ti,audpwron-gpio = <&gpio6 0 GPIO_ACTIVE_HIGH>; /* gpio_160 */ + + vio-supply = <&v1v8>; + v2v1-supply = <&v2v1>; + enable-active-high; + }; +}; + +#include "twl6030.dtsi" +#include "twl6030_omap4.dtsi" + +/* on-board bluetooth / WiFi module */ +&i2c4 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c4_pins>; + + clock-frequency = <400000>; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + + vmmc-supply = <&vmmc>; + ti,bus-width = <4>; + ti,non-removable; /* FIXME: use PMIC_MMC detect */ +}; + +&mmc2 { + status = "disabled"; +}; + +/* mmc3 is available to the expansion board */ + +&mmc4 { + status = "disabled"; +}; + +/* on-board WiFi module */ +&mmc5 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc5_pins>; + + vmmc-supply = <&w2cbw0015_vmmc>; + ti,bus-width = <4>; + ti,non-removable; + cap-power-off-card; +}; + +&twl_usb_comparator { + usb-supply = <&vusb>; +}; + +&usb_otg_hs { + interface-type = <1>; + mode = <3>; + power = <50>; +}; + +&usbhshost { + port1-mode = "ehci-phy"; +}; + +&usbhsehci { + phys = <&hsusb1_phy>; +}; + diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 88c6a05cab41..cbc45cfc44e9 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -83,12 +83,8 @@ compatible = "usb-nop-xceiv"; reset-gpios = <&gpio2 30 GPIO_ACTIVE_LOW>; /* gpio_62 */ vcc-supply = <&hsusb1_power>; - /** - * FIXME: - * put the right clock phandle here when available - * clocks = <&auxclk3>; - * clock-names = "main_clk"; - */ + clocks = <&auxclk3_ck>; + clock-names = "main_clk"; clock-frequency = <19200000>; }; @@ -109,9 +105,6 @@ &omap4_pmx_core { pinctrl-names = "default"; pinctrl-0 = < - &twl6040_pins - &mcpdm_pins - &mcbsp1_pins &dss_dpi_pins &tfp410_pins &dss_hdmi_pins @@ -300,6 +293,10 @@ twl6040: twl@4b { compatible = "ti,twl6040"; reg = <0x4b>; + + pinctrl-names = "default"; + pinctrl-0 = <&twl6040_pins>; + /* IRQ# = 119 */ interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */ interrupt-parent = <&gic>; @@ -380,16 +377,16 @@ device-handle = <&elpida_ECB240ABACN>; }; -&mcbsp2 { - status = "disabled"; -}; - -&mcbsp3 { - status = "disabled"; +&mcbsp1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp1_pins>; + status = "okay"; }; -&dmic { - status = "disabled"; +&mcpdm { + pinctrl-names = "default"; + pinctrl-0 = <&mcpdm_pins>; + status = "okay"; }; &twl_usb_comparator { diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index dbc81fb6ef03..9bbbbec1d63d 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -158,11 +158,6 @@ &omap4_pmx_core { pinctrl-names = "default"; pinctrl-0 = < - &twl6040_pins - &mcpdm_pins - &dmic_pins - &mcbsp1_pins - &mcbsp2_pins &dss_hdmi_pins &tpd12s015_pins >; @@ -326,6 +321,10 @@ twl6040: twl@4b { compatible = "ti,twl6040"; reg = <0x4b>; + + pinctrl-names = "default"; + pinctrl-0 = <&twl6040_pins>; + /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */ interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */ interrupt-parent = <&gic>; @@ -537,8 +536,28 @@ pinctrl-0 = <&uart4_pins>; }; -&mcbsp3 { - status = "disabled"; +&mcbsp1 { + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp1_pins>; + status = "okay"; +}; + +&mcbsp2 { + pinctrl-names = "default"; + pinctrl-0 = <&mcbsp2_pins>; + status = "okay"; +}; + +&dmic { + pinctrl-names = "default"; + pinctrl-0 = <&dmic_pins>; + status = "okay"; +}; + +&mcpdm { + pinctrl-names = "default"; + pinctrl-0 = <&mcpdm_pins>; + status = "okay"; }; &twl_usb_comparator { diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 69409f7e05dc..fe61976dc1a5 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -36,6 +36,11 @@ device_type = "cpu"; next-level-cache = <&L2>; reg = <0x0>; + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ }; cpu@1 { compatible = "arm,cortex-a9"; @@ -315,6 +320,7 @@ compatible = "ti,omap4-hwspinlock"; reg = <0x4a0f6000 0x1000>; ti,hwmods = "spinlock"; + #hwlock-cells = <1>; }; i2c1: i2c@48070000 { @@ -463,6 +469,21 @@ dma-names = "tx", "rx"; }; + mmu_dsp: mmu@4a066000 { + compatible = "ti,omap4-iommu"; + reg = <0x4a066000 0x100>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu_dsp"; + }; + + mmu_ipu: mmu@55082000 { + compatible = "ti,omap4-iommu"; + reg = <0x55082000 0x100>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu_ipu"; + ti,iommu-bus-err-back; + }; + wdt2: wdt@4a314000 { compatible = "ti,omap4-wdt", "ti,omap3-wdt"; reg = <0x4a314000 0x80>; @@ -480,6 +501,7 @@ dmas = <&sdma 65>, <&sdma 66>; dma-names = "up_link", "dn_link"; + status = "disabled"; }; dmic: dmic@4012e000 { @@ -491,6 +513,7 @@ ti,hwmods = "dmic"; dmas = <&sdma 67>; dma-names = "up_link"; + status = "disabled"; }; mcbsp1: mcbsp@40122000 { @@ -505,6 +528,7 @@ dmas = <&sdma 33>, <&sdma 34>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp2: mcbsp@40124000 { @@ -519,6 +543,7 @@ dmas = <&sdma 17>, <&sdma 18>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp3: mcbsp@40126000 { @@ -533,6 +558,7 @@ dmas = <&sdma 19>, <&sdma 20>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp4: mcbsp@48096000 { @@ -546,6 +572,7 @@ dmas = <&sdma 31>, <&sdma 32>; dma-names = "tx", "rx"; + status = "disabled"; }; keypad: keypad@4a31c000 { @@ -556,6 +583,13 @@ ti,hwmods = "kbd"; }; + dmm@4e000000 { + compatible = "ti,omap4-dmm"; + reg = <0x4e000000 0x800>; + interrupts = <0 113 0x4>; + ti,hwmods = "dmm"; + }; + emif1: emif@4c000000 { compatible = "ti,emif-4d"; reg = <0x4c000000 0x100>; @@ -701,14 +735,14 @@ ranges; usbhsohci: ohci@4a064800 { - compatible = "ti,ohci-omap3", "usb-ohci"; + compatible = "ti,ohci-omap3"; reg = <0x4a064800 0x400>; interrupt-parent = <&gic>; interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; }; usbhsehci: ehci@4a064c00 { - compatible = "ti,ehci-omap", "usb-ehci"; + compatible = "ti,ehci-omap"; reg = <0x4a064c00 0x400>; interrupt-parent = <&gic>; interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; @@ -759,6 +793,32 @@ dmas = <&sdma 117>, <&sdma 116>; dma-names = "tx", "rx"; }; + + abb_mpu: regulator-abb-mpu { + compatible = "ti,abb-v2"; + regulator-name = "abb_mpu"; + #address-cells = <0>; + #size-cells = <0>; + ti,tranxdone-status-mask = <0x80>; + clocks = <&sys_clkin_ck>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + + status = "disabled"; + }; + + abb_iva: regulator-abb-iva { + compatible = "ti,abb-v2"; + regulator-name = "abb_iva"; + #address-cells = <0>; + #size-cells = <0>; + ti,tranxdone-status-mask = <0x80000000>; + clocks = <&sys_clkin_ck>; + ti,settling-time = <50>; + ti,clock-cycles = <16>; + + status = "disabled"; + }; }; }; diff --git a/arch/arm/boot/dts/omap443x.dtsi b/arch/arm/boot/dts/omap443x.dtsi index 8c1cfad30d60..0adfa1d1ef20 100644 --- a/arch/arm/boot/dts/omap443x.dtsi +++ b/arch/arm/boot/dts/omap443x.dtsi @@ -43,6 +43,32 @@ #thermal-sensor-cells = <0>; }; }; + + ocp { + abb_mpu: regulator-abb-mpu { + status = "okay"; + + reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>; + reg-names = "base-address", "int-address"; + + ti,abb_info = < + /*uV ABB efuse rbb_m fbb_m vset_m*/ + 1025000 0 0 0 0 0 + 1200000 0 0 0 0 0 + 1313000 0 0 0 0 0 + 1375000 1 0 0 0 0 + 1389000 1 0 0 0 0 + >; + }; + + /* Default unused, just provide register info for record */ + abb_iva: regulator-abb-iva { + reg = <0x4a307bd8 0x8>, <0x4a306010 0x4>; + reg-names = "base-address", "int-address"; + }; + + }; + }; /include/ "omap443x-clocks.dtsi" diff --git a/arch/arm/boot/dts/omap4460.dtsi b/arch/arm/boot/dts/omap4460.dtsi index 6b32f520741a..194f9ef0a009 100644 --- a/arch/arm/boot/dts/omap4460.dtsi +++ b/arch/arm/boot/dts/omap4460.dtsi @@ -50,7 +50,44 @@ #thermal-sensor-cells = <0>; }; + + abb_mpu: regulator-abb-mpu { + status = "okay"; + + reg = <0x4a307bd0 0x8>, <0x4a306014 0x4>, + <0x4A002268 0x4>; + reg-names = "base-address", "int-address", + "efuse-address"; + + ti,abb_info = < + /*uV ABB efuse rbb_m fbb_m vset_m*/ + 1025000 0 0 0 0 0 + 1200000 0 0 0 0 0 + 1313000 0 0 0x100000 0x40000 0 + 1375000 1 0 0 0 0 + 1389000 1 0 0 0 0 + >; + }; + + abb_iva: regulator-abb-iva { + status = "okay"; + + reg = <0x4a307bd8 0x8>, <0x4a306010 0x4>, + <0x4A002268 0x4>; + reg-names = "base-address", "int-address", + "efuse-address"; + + ti,abb_info = < + /*uV ABB efuse rbb_m fbb_m vset_m*/ + 950000 0 0 0 0 0 + 1140000 0 0 0 0 0 + 1291000 0 0 0x200000 0 0 + 1375000 1 0 0 0 0 + 1376000 1 0 0 0 0 + >; + }; }; + }; /include/ "omap446x-clocks.dtsi" diff --git a/arch/arm/boot/dts/omap5-uevm.dts b/arch/arm/boot/dts/omap5-uevm.dts index 002fa70180a5..3b99ec25b748 100644 --- a/arch/arm/boot/dts/omap5-uevm.dts +++ b/arch/arm/boot/dts/omap5-uevm.dts @@ -31,12 +31,8 @@ hsusb2_phy: hsusb2_phy { compatible = "usb-nop-xceiv"; reset-gpios = <&gpio3 16 GPIO_ACTIVE_LOW>; /* gpio3_80 HUB_NRESET */ - /** - * FIXME - * Put the right clock phandle here when available - * clocks = <&auxclk1>; - * clock-names = "main_clk"; - */ + clocks = <&auxclk1_ck>; + clock-names = "main_clk"; clock-frequency = <19200000>; }; diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index 7a16647c76f4..8292ad0fe69f 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -49,6 +49,12 @@ 1000000 1060000 1500000 1250000 >; + + clocks = <&dpll_mpu_ck>; + clock-names = "cpu"; + + clock-latency = <300000>; /* From omap-cpufreq driver */ + /* cooling options */ cooling-min-level = <0>; cooling-max-level = <2>; @@ -355,6 +361,7 @@ compatible = "ti,omap4-hwspinlock"; reg = <0x4a0f6000 0x1000>; ti,hwmods = "spinlock"; + #hwlock-cells = <1>; }; mcspi1: spi@48098000 { @@ -515,6 +522,21 @@ dma-names = "tx", "rx"; }; + mmu_dsp: mmu@4a066000 { + compatible = "ti,omap4-iommu"; + reg = <0x4a066000 0x100>; + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu_dsp"; + }; + + mmu_ipu: mmu@55082000 { + compatible = "ti,omap4-iommu"; + reg = <0x55082000 0x100>; + interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>; + ti,hwmods = "mmu_ipu"; + ti,iommu-bus-err-back; + }; + keypad: keypad@4ae1c000 { compatible = "ti,omap4-keypad"; reg = <0x4ae1c000 0x400>; @@ -531,6 +553,7 @@ dmas = <&sdma 65>, <&sdma 66>; dma-names = "up_link", "dn_link"; + status = "disabled"; }; dmic: dmic@4012e000 { @@ -542,6 +565,7 @@ ti,hwmods = "dmic"; dmas = <&sdma 67>; dma-names = "up_link"; + status = "disabled"; }; mcbsp1: mcbsp@40122000 { @@ -556,6 +580,7 @@ dmas = <&sdma 33>, <&sdma 34>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp2: mcbsp@40124000 { @@ -570,6 +595,7 @@ dmas = <&sdma 17>, <&sdma 18>; dma-names = "tx", "rx"; + status = "disabled"; }; mcbsp3: mcbsp@40126000 { @@ -584,6 +610,7 @@ dmas = <&sdma 19>, <&sdma 20>; dma-names = "tx", "rx"; + status = "disabled"; }; timer1: timer@4ae18000 { @@ -685,6 +712,13 @@ ti,hwmods = "wd_timer2"; }; + dmm@4e000000 { + compatible = "ti,omap5-dmm"; + reg = <0x4e000000 0x800>; + interrupts = <0 113 0x4>; + ti,hwmods = "dmm"; + }; + emif1: emif@4c000000 { compatible = "ti,emif-4d5"; ti,hwmods = "emif1"; @@ -734,7 +768,8 @@ compatible = "snps,dwc3"; reg = <0x4a030000 0x10000>; interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; - usb-phy = <&usb2_phy>, <&usb3_phy>; + phys = <&usb2_phy>, <&usb3_phy>; + phy-names = "usb2-phy", "usb3-phy"; dr_mode = "peripheral"; tx-fifo-resize; }; @@ -751,6 +786,7 @@ compatible = "ti,omap-usb2"; reg = <0x4a084000 0x7c>; ctrl-module = <&omap_control_usb2phy>; + #phy-cells = <0>; }; usb3_phy: usb3phy@4a084400 { @@ -760,6 +796,7 @@ <0x4a084c00 0x40>; reg-names = "phy_rx", "phy_tx", "pll_ctrl"; ctrl-module = <&omap_control_usb3phy>; + #phy-cells = <0>; }; }; @@ -779,14 +816,14 @@ ranges; usbhsohci: ohci@4a064800 { - compatible = "ti,ohci-omap3", "usb-ohci"; + compatible = "ti,ohci-omap3"; reg = <0x4a064800 0x400>; interrupt-parent = <&gic>; interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; }; usbhsehci: ehci@4a064c00 { - compatible = "ti,ehci-omap", "usb-ehci"; + compatible = "ti,ehci-omap"; reg = <0x4a064c00 0x400>; interrupt-parent = <&gic>; interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi index 69d6c4edea30..c52a9e964a44 100644 --- a/arch/arm/boot/dts/qcom-msm8660.dtsi +++ b/arch/arm/boot/dts/qcom-msm8660.dtsi @@ -9,6 +9,30 @@ compatible = "qcom,msm8660"; interrupt-parent = <&intc>; + cpus { + #address-cells = <1>; + #size-cells = <0>; + compatible = "qcom,scorpion"; + enable-method = "qcom,gcc-msm8660"; + + cpu@0 { + device_type = "cpu"; + reg = <0>; + next-level-cache = <&L2>; + }; + + cpu@1 { + device_type = "cpu"; + reg = <1>; + next-level-cache = <&L2>; + }; + + L2: l2-cache { + compatible = "cache"; + cache-level = <2>; + }; + }; + intc: interrupt-controller@2080000 { compatible = "qcom,msm-8660-qgic"; interrupt-controller; diff --git a/arch/arm/boot/dts/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom-msm8960.dtsi index 3a9c3caa9aad..997b7b94e117 100644 --- a/arch/arm/boot/dts/qcom-msm8960.dtsi +++ b/arch/arm/boot/dts/qcom-msm8960.dtsi @@ -9,6 +9,36 @@ compatible = "qcom,msm8960"; interrupt-parent = <&intc>; + cpus { + #address-cells = <1>; + #size-cells = <0>; + interrupts = <1 14 0x304>; + compatible = "qcom,krait"; + enable-method = "qcom,kpss-acc-v1"; + + cpu@0 { + device_type = "cpu"; + reg = <0>; + next-level-cache = <&L2>; + qcom,acc = <&acc0>; + qcom,saw = <&saw0>; + }; + + cpu@1 { + device_type = "cpu"; + reg = <1>; + next-level-cache = <&L2>; + qcom,acc = <&acc1>; + qcom,saw = <&saw1>; + }; + + L2: l2-cache { + compatible = "cache"; + cache-level = <2>; + interrupts = <0 2 0x4>; + }; + }; + cpu-pmu { compatible = "qcom,krait-pmu"; interrupts = <1 10 0x304>; @@ -59,6 +89,28 @@ #reset-cells = <1>; }; + acc0: clock-controller@2088000 { + compatible = "qcom,kpss-acc-v1"; + reg = <0x02088000 0x1000>, <0x02008000 0x1000>; + }; + + acc1: clock-controller@2098000 { + compatible = "qcom,kpss-acc-v1"; + reg = <0x02098000 0x1000>, <0x02008000 0x1000>; + }; + + saw0: regulator@2089000 { + compatible = "qcom,saw2"; + reg = <0x02089000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + + saw1: regulator@2099000 { + compatible = "qcom,saw2"; + reg = <0x02099000 0x1000>, <0x02009000 0x1000>; + regulator; + }; + serial@16440000 { compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm"; reg = <0x16440000 0x1000>, @@ -73,4 +125,11 @@ reg = <0x500000 0x1000>; qcom,controller-type = "pmic-arbiter"; }; + + rng@1a500000 { + compatible = "qcom,prng"; + reg = <0x1a500000 0x200>; + clocks = <&gcc PRNG_CLK>; + clock-names = "core"; + }; }; diff --git a/arch/arm/boot/dts/qcom-msm8974.dtsi b/arch/arm/boot/dts/qcom-msm8974.dtsi index 1eff4130cde0..f68723918b3f 100644 --- a/arch/arm/boot/dts/qcom-msm8974.dtsi +++ b/arch/arm/boot/dts/qcom-msm8974.dtsi @@ -9,6 +9,49 @@ compatible = "qcom,msm8974"; interrupt-parent = <&intc>; + cpus { + #address-cells = <1>; + #size-cells = <0>; + interrupts = <1 9 0xf04>; + compatible = "qcom,krait"; + enable-method = "qcom,kpss-acc-v2"; + + cpu@0 { + device_type = "cpu"; + reg = <0>; + next-level-cache = <&L2>; + qcom,acc = <&acc0>; + }; + + cpu@1 { + device_type = "cpu"; + reg = <1>; + next-level-cache = <&L2>; + qcom,acc = <&acc1>; + }; + + cpu@2 { + device_type = "cpu"; + reg = <2>; + next-level-cache = <&L2>; + qcom,acc = <&acc2>; + }; + + cpu@3 { + device_type = "cpu"; + reg = <3>; + next-level-cache = <&L2>; + qcom,acc = <&acc3>; + }; + + L2: l2-cache { + compatible = "cache"; + cache-level = <2>; + interrupts = <0 2 0x4>; + qcom,saw = <&saw_l2>; + }; + }; + cpu-pmu { compatible = "qcom,krait-pmu"; interrupts = <1 7 0xf04>; @@ -96,6 +139,32 @@ }; }; + saw_l2: regulator@f9012000 { + compatible = "qcom,saw2"; + reg = <0xf9012000 0x1000>; + regulator; + }; + + acc0: clock-controller@f9088000 { + compatible = "qcom,kpss-acc-v2"; + reg = <0xf9088000 0x1000>, <0xf9008000 0x1000>; + }; + + acc1: clock-controller@f9098000 { + compatible = "qcom,kpss-acc-v2"; + reg = <0xf9098000 0x1000>, <0xf9008000 0x1000>; + }; + + acc2: clock-controller@f90a8000 { + compatible = "qcom,kpss-acc-v2"; + reg = <0xf90a8000 0x1000>, <0xf9008000 0x1000>; + }; + + acc3: clock-controller@f90b8000 { + compatible = "qcom,kpss-acc-v2"; + reg = <0xf90b8000 0x1000>, <0xf9008000 0x1000>; + }; + restart@fc4ab000 { compatible = "qcom,pshold"; reg = <0xfc4ab000 0x4>; @@ -122,5 +191,12 @@ clocks = <&gcc GCC_BLSP1_UART2_APPS_CLK>, <&gcc GCC_BLSP1_AHB_CLK>; clock-names = "core", "iface"; }; + + rng@f9bff000 { + compatible = "qcom,prng"; + reg = <0xf9bff000 0x200>; + clocks = <&gcc GCC_PRNG_AHB_CLK>; + clock-names = "core"; + }; }; }; diff --git a/arch/arm/boot/dts/r7s72100-genmai-reference.dts b/arch/arm/boot/dts/r7s72100-genmai-reference.dts index da19c70ed82b..e664611a47c8 100644 --- a/arch/arm/boot/dts/r7s72100-genmai-reference.dts +++ b/arch/arm/boot/dts/r7s72100-genmai-reference.dts @@ -9,7 +9,7 @@ */ /dts-v1/; -/include/ "r7s72100.dtsi" +#include "r7s72100.dtsi" / { model = "Genmai"; @@ -29,3 +29,14 @@ #size-cells = <1>; }; }; + +&i2c2 { + status = "okay"; + clock-frequency = <400000>; + + eeprom@50 { + compatible = "renesas,24c128"; + reg = <0x50>; + pagesize = <64>; + }; +}; diff --git a/arch/arm/boot/dts/r7s72100.dtsi b/arch/arm/boot/dts/r7s72100.dtsi index 46b82aa7dc4e..ee700717a34b 100644 --- a/arch/arm/boot/dts/r7s72100.dtsi +++ b/arch/arm/boot/dts/r7s72100.dtsi @@ -8,12 +8,26 @@ * kind, whether express or implied. */ +#include <dt-bindings/interrupt-controller/irq.h> + / { compatible = "renesas,r7s72100"; interrupt-parent = <&gic>; #address-cells = <1>; #size-cells = <1>; + aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + spi0 = &spi0; + spi1 = &spi1; + spi2 = &spi2; + spi3 = &spi3; + spi4 = &spi4; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -33,4 +47,137 @@ reg = <0xe8201000 0x1000>, <0xe8202000 0x1000>; }; + + i2c0: i2c@fcfee000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; + reg = <0xfcfee000 0x44>; + interrupts = <0 157 IRQ_TYPE_LEVEL_HIGH>, + <0 158 IRQ_TYPE_EDGE_RISING>, + <0 159 IRQ_TYPE_EDGE_RISING>, + <0 160 IRQ_TYPE_LEVEL_HIGH>, + <0 161 IRQ_TYPE_LEVEL_HIGH>, + <0 162 IRQ_TYPE_LEVEL_HIGH>, + <0 163 IRQ_TYPE_LEVEL_HIGH>, + <0 164 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <100000>; + status = "disabled"; + }; + + i2c1: i2c@fcfee400 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; + reg = <0xfcfee400 0x44>; + interrupts = <0 165 IRQ_TYPE_LEVEL_HIGH>, + <0 166 IRQ_TYPE_EDGE_RISING>, + <0 167 IRQ_TYPE_EDGE_RISING>, + <0 168 IRQ_TYPE_LEVEL_HIGH>, + <0 169 IRQ_TYPE_LEVEL_HIGH>, + <0 170 IRQ_TYPE_LEVEL_HIGH>, + <0 171 IRQ_TYPE_LEVEL_HIGH>, + <0 172 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <100000>; + status = "disabled"; + }; + + i2c2: i2c@fcfee800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; + reg = <0xfcfee800 0x44>; + interrupts = <0 173 IRQ_TYPE_LEVEL_HIGH>, + <0 174 IRQ_TYPE_EDGE_RISING>, + <0 175 IRQ_TYPE_EDGE_RISING>, + <0 176 IRQ_TYPE_LEVEL_HIGH>, + <0 177 IRQ_TYPE_LEVEL_HIGH>, + <0 178 IRQ_TYPE_LEVEL_HIGH>, + <0 179 IRQ_TYPE_LEVEL_HIGH>, + <0 180 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <100000>; + status = "disabled"; + }; + + i2c3: i2c@fcfeec00 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,riic-r7s72100", "renesas,riic-rz"; + reg = <0xfcfeec00 0x44>; + interrupts = <0 181 IRQ_TYPE_LEVEL_HIGH>, + <0 182 IRQ_TYPE_EDGE_RISING>, + <0 183 IRQ_TYPE_EDGE_RISING>, + <0 184 IRQ_TYPE_LEVEL_HIGH>, + <0 185 IRQ_TYPE_LEVEL_HIGH>, + <0 186 IRQ_TYPE_LEVEL_HIGH>, + <0 187 IRQ_TYPE_LEVEL_HIGH>, + <0 188 IRQ_TYPE_LEVEL_HIGH>; + clock-frequency = <100000>; + status = "disabled"; + }; + + spi0: spi@e800c800 { + compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; + reg = <0xe800c800 0x24>; + interrupts = <0 238 IRQ_TYPE_LEVEL_HIGH>, + <0 239 IRQ_TYPE_LEVEL_HIGH>, + <0 240 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", "rx", "tx"; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi1: spi@e800d000 { + compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; + reg = <0xe800d000 0x24>; + interrupts = <0 241 IRQ_TYPE_LEVEL_HIGH>, + <0 242 IRQ_TYPE_LEVEL_HIGH>, + <0 243 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", "rx", "tx"; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi2: spi@e800d800 { + compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; + reg = <0xe800d800 0x24>; + interrupts = <0 244 IRQ_TYPE_LEVEL_HIGH>, + <0 245 IRQ_TYPE_LEVEL_HIGH>, + <0 246 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", "rx", "tx"; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi3: spi@e800e000 { + compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; + reg = <0xe800e000 0x24>; + interrupts = <0 247 IRQ_TYPE_LEVEL_HIGH>, + <0 248 IRQ_TYPE_LEVEL_HIGH>, + <0 249 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", "rx", "tx"; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + spi4: spi@e800e800 { + compatible = "renesas,rspi-r7s72100", "renesas,rspi-rz"; + reg = <0xe800e800 0x24>; + interrupts = <0 250 IRQ_TYPE_LEVEL_HIGH>, + <0 251 IRQ_TYPE_LEVEL_HIGH>, + <0 252 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "error", "rx", "tx"; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; }; diff --git a/arch/arm/boot/dts/r8a7778.dtsi b/arch/arm/boot/dts/r8a7778.dtsi index ddb3bd7a8838..85c5b3b99f5e 100644 --- a/arch/arm/boot/dts/r8a7778.dtsi +++ b/arch/arm/boot/dts/r8a7778.dtsi @@ -203,46 +203,6 @@ status = "disabled"; }; - i2c0: i2c@ffc70000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "renesas,i2c-r8a7778"; - reg = <0xffc70000 0x1000>; - interrupt-parent = <&gic>; - interrupts = <0 67 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - i2c1: i2c@ffc71000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "renesas,i2c-r8a7778"; - reg = <0xffc71000 0x1000>; - interrupt-parent = <&gic>; - interrupts = <0 78 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - i2c2: i2c@ffc72000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "renesas,i2c-r8a7778"; - reg = <0xffc72000 0x1000>; - interrupt-parent = <&gic>; - interrupts = <0 76 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - - i2c3: i2c@ffc73000 { - #address-cells = <1>; - #size-cells = <0>; - compatible = "renesas,i2c-r8a7778"; - reg = <0xffc73000 0x1000>; - interrupt-parent = <&gic>; - interrupts = <0 77 IRQ_TYPE_LEVEL_HIGH>; - status = "disabled"; - }; - hspi0: spi@fffc7000 { compatible = "renesas,hspi"; reg = <0xfffc7000 0x18>; diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts index 57569cba1528..6e99eb2df076 100644 --- a/arch/arm/boot/dts/r8a7790-lager.dts +++ b/arch/arm/boot/dts/r8a7790-lager.dts @@ -1,7 +1,8 @@ /* * Device Tree Source for the Lager board * - * Copyright (C) 2013 Renesas Solutions Corp. + * Copyright (C) 2013-2014 Renesas Solutions Corp. + * Copyright (C) 2014 Cogent Embedded, Inc. * * This file is licensed under the terms of the GNU General Public License * version 2. This program is licensed "as is" without any warranty of any @@ -56,6 +57,54 @@ regulator-boot-on; regulator-always-on; }; + + vcc_sdhi0: regulator@1 { + compatible = "regulator-fixed"; + + regulator-name = "SDHI0 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio5 24 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vccq_sdhi0: regulator@2 { + compatible = "regulator-gpio"; + + regulator-name = "SDHI0 VccQ"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio5 29 GPIO_ACTIVE_HIGH>; + gpios-states = <1>; + states = <3300000 1 + 1800000 0>; + }; + + vcc_sdhi2: regulator@3 { + compatible = "regulator-fixed"; + + regulator-name = "SDHI2 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio5 25 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vccq_sdhi2: regulator@4 { + compatible = "regulator-gpio"; + + regulator-name = "SDHI2 VccQ"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio5 30 GPIO_ACTIVE_HIGH>; + gpios-states = <1>; + states = <3300000 1 + 1800000 0>; + }; }; &extal_clk { @@ -63,23 +112,68 @@ }; &pfc { - pinctrl-0 = <&scif0_pins &scif1_pins>; + pinctrl-0 = <&du_pins &scif0_pins &scif1_pins>; pinctrl-names = "default"; + du_pins: du { + renesas,groups = "du_rgb666", "du_sync_1", "du_clk_out_0"; + renesas,function = "du"; + }; + scif0_pins: serial0 { renesas,groups = "scif0_data"; renesas,function = "scif0"; }; + ether_pins: ether { + renesas,groups = "eth_link", "eth_mdio", "eth_rmii"; + renesas,function = "eth"; + }; + + phy1_pins: phy1 { + renesas,groups = "intc_irq0"; + renesas,function = "intc"; + }; + scif1_pins: serial1 { renesas,groups = "scif1_data"; renesas,function = "scif1"; }; + sdhi0_pins: sd0 { + renesas,gpios = "sdhi0_data4", "sdhi0_ctrl"; + renesas,function = "sdhi0"; + }; + + sdhi2_pins: sd2 { + renesas,gpios = "sdhi2_data4", "sdhi2_ctrl"; + renesas,function = "sdhi2"; + }; + mmc1_pins: mmc1 { renesas,groups = "mmc1_data8", "mmc1_ctrl"; renesas,function = "mmc1"; }; + + qspi_pins: spi { + renesas,groups = "qspi_ctrl", "qspi_data4"; + renesas,function = "qspi"; + }; +}; + +ðer { + pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-names = "default"; + + phy-handle = <&phy1>; + renesas,ether-link-active-low; + status = "ok"; + + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&irqc0>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; }; &mmcif1 { @@ -91,3 +185,58 @@ non-removable; status = "okay"; }; + +&sata1 { + status = "okay"; +}; + +&spi { + pinctrl-0 = <&qspi_pins>; + pinctrl-names = "default"; + + status = "okay"; + + flash: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,s25fl512s"; + reg = <0>; + spi-max-frequency = <30000000>; + m25p,fast-read; + + partition@0 { + label = "loader"; + reg = <0x00000000 0x00040000>; + read-only; + }; + partition@40000 { + label = "user"; + reg = <0x00040000 0x00400000>; + read-only; + }; + partition@440000 { + label = "flash"; + reg = <0x00440000 0x03bc0000>; + }; + }; +}; + +&sdhi0 { + pinctrl-0 = <&sdhi0_pins>; + pinctrl-names = "default"; + + vmmc-supply = <&vcc_sdhi0>; + vqmmc-supply = <&vccq_sdhi0>; + cd-gpios = <&gpio3 6 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&sdhi2 { + pinctrl-0 = <&sdhi2_pins>; + pinctrl-names = "default"; + + vmmc-supply = <&vcc_sdhi2>; + vqmmc-supply = <&vccq_sdhi2>; + cd-gpios = <&gpio3 22 GPIO_ACTIVE_LOW>; + status = "okay"; +}; diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi index 71b1251f79c7..e22520dff8c6 100644 --- a/arch/arm/boot/dts/r8a7790.dtsi +++ b/arch/arm/boot/dts/r8a7790.dtsi @@ -1,7 +1,8 @@ /* * Device Tree Source for the r8a7790 SoC * - * Copyright (C) 2013 Renesas Solutions Corp. + * Copyright (C) 2013-2014 Renesas Solutions Corp. + * Copyright (C) 2014 Cogent Embedded Inc. * * This file is licensed under the terms of the GNU General Public License * version 2. This program is licensed "as is" without any warranty of any @@ -18,6 +19,13 @@ #address-cells = <2>; #size-cells = <2>; + aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -94,7 +102,6 @@ gpio0: gpio@e6050000 { compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar"; reg = <0 0xe6050000 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 4 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -106,7 +113,6 @@ gpio1: gpio@e6051000 { compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar"; reg = <0 0xe6051000 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -118,7 +124,6 @@ gpio2: gpio@e6052000 { compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar"; reg = <0 0xe6052000 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -130,7 +135,6 @@ gpio3: gpio@e6053000 { compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar"; reg = <0 0xe6053000 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -142,7 +146,6 @@ gpio4: gpio@e6054000 { compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar"; reg = <0 0xe6054000 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -154,7 +157,6 @@ gpio5: gpio@e6055000 { compatible = "renesas,gpio-r8a7790", "renesas,gpio-rcar"; reg = <0 0xe6055000 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -166,8 +168,8 @@ thermal@e61f0000 { compatible = "renesas,thermal-r8a7790", "renesas,rcar-thermal"; reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>; - interrupt-parent = <&gic>; interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks R8A7790_CLK_THERMAL>; }; timer { @@ -183,7 +185,6 @@ #interrupt-cells = <2>; interrupt-controller; reg = <0 0xe61c0000 0 0x200>; - interrupt-parent = <&gic>; interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>, <0 1 IRQ_TYPE_LEVEL_HIGH>, <0 2 IRQ_TYPE_LEVEL_HIGH>, @@ -195,7 +196,6 @@ #size-cells = <0>; compatible = "renesas,i2c-r8a7790"; reg = <0 0xe6508000 0 0x40>; - interrupt-parent = <&gic>; interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7790_CLK_I2C0>; status = "disabled"; @@ -206,7 +206,6 @@ #size-cells = <0>; compatible = "renesas,i2c-r8a7790"; reg = <0 0xe6518000 0 0x40>; - interrupt-parent = <&gic>; interrupts = <0 288 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7790_CLK_I2C1>; status = "disabled"; @@ -217,7 +216,6 @@ #size-cells = <0>; compatible = "renesas,i2c-r8a7790"; reg = <0 0xe6530000 0 0x40>; - interrupt-parent = <&gic>; interrupts = <0 286 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7790_CLK_I2C2>; status = "disabled"; @@ -228,7 +226,6 @@ #size-cells = <0>; compatible = "renesas,i2c-r8a7790"; reg = <0 0xe6540000 0 0x40>; - interrupt-parent = <&gic>; interrupts = <0 290 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp9_clks R8A7790_CLK_I2C3>; status = "disabled"; @@ -237,7 +234,6 @@ mmcif0: mmcif@ee200000 { compatible = "renesas,mmcif-r8a7790", "renesas,sh-mmcif"; reg = <0 0xee200000 0 0x80>; - interrupt-parent = <&gic>; interrupts = <0 169 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_MMCIF0>; reg-io-width = <4>; @@ -247,7 +243,6 @@ mmcif1: mmc@ee220000 { compatible = "renesas,mmcif-r8a7790", "renesas,sh-mmcif"; reg = <0 0xee220000 0 0x80>; - interrupt-parent = <&gic>; interrupts = <0 170 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_MMCIF1>; reg-io-width = <4>; @@ -262,7 +257,6 @@ sdhi0: sd@ee100000 { compatible = "renesas,sdhi-r8a7790"; reg = <0 0xee100000 0 0x200>; - interrupt-parent = <&gic>; interrupts = <0 165 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_SDHI0>; cap-sd-highspeed; @@ -272,7 +266,6 @@ sdhi1: sd@ee120000 { compatible = "renesas,sdhi-r8a7790"; reg = <0 0xee120000 0 0x200>; - interrupt-parent = <&gic>; interrupts = <0 166 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_SDHI1>; cap-sd-highspeed; @@ -282,7 +275,6 @@ sdhi2: sd@ee140000 { compatible = "renesas,sdhi-r8a7790"; reg = <0 0xee140000 0 0x100>; - interrupt-parent = <&gic>; interrupts = <0 167 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_SDHI2>; cap-sd-highspeed; @@ -292,13 +284,129 @@ sdhi3: sd@ee160000 { compatible = "renesas,sdhi-r8a7790"; reg = <0 0xee160000 0 0x100>; - interrupt-parent = <&gic>; interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>; clocks = <&mstp3_clks R8A7790_CLK_SDHI3>; cap-sd-highspeed; status = "disabled"; }; + scifa0: serial@e6c40000 { + compatible = "renesas,scifa-r8a7790", "renesas,scifa"; + reg = <0 0xe6c40000 0 64>; + interrupts = <0 144 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7790_CLK_SCIFA0>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scifa1: serial@e6c50000 { + compatible = "renesas,scifa-r8a7790", "renesas,scifa"; + reg = <0 0xe6c50000 0 64>; + interrupts = <0 145 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7790_CLK_SCIFA1>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scifa2: serial@e6c60000 { + compatible = "renesas,scifa-r8a7790", "renesas,scifa"; + reg = <0 0xe6c60000 0 64>; + interrupts = <0 151 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7790_CLK_SCIFA2>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scifb0: serial@e6c20000 { + compatible = "renesas,scifb-r8a7790", "renesas,scifb"; + reg = <0 0xe6c20000 0 64>; + interrupts = <0 148 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7790_CLK_SCIFB0>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scifb1: serial@e6c30000 { + compatible = "renesas,scifb-r8a7790", "renesas,scifb"; + reg = <0 0xe6c30000 0 64>; + interrupts = <0 149 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7790_CLK_SCIFB1>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scifb2: serial@e6ce0000 { + compatible = "renesas,scifb-r8a7790", "renesas,scifb"; + reg = <0 0xe6ce0000 0 64>; + interrupts = <0 150 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7790_CLK_SCIFB2>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scif0: serial@e6e60000 { + compatible = "renesas,scif-r8a7790", "renesas,scif"; + reg = <0 0xe6e60000 0 64>; + interrupts = <0 152 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7790_CLK_SCIF0>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scif1: serial@e6e68000 { + compatible = "renesas,scif-r8a7790", "renesas,scif"; + reg = <0 0xe6e68000 0 64>; + interrupts = <0 153 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7790_CLK_SCIF1>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + hscif0: serial@e62c0000 { + compatible = "renesas,hscif-r8a7790", "renesas,hscif"; + reg = <0 0xe62c0000 0 96>; + interrupts = <0 154 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7790_CLK_HSCIF0>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + hscif1: serial@e62c8000 { + compatible = "renesas,hscif-r8a7790", "renesas,hscif"; + reg = <0 0xe62c8000 0 96>; + interrupts = <0 155 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7790_CLK_HSCIF1>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + ether: ethernet@ee700000 { + compatible = "renesas,ether-r8a7790"; + reg = <0 0xee700000 0 0x400>; + interrupts = <0 162 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7790_CLK_ETHER>; + phy-mode = "rmii"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + sata0: sata@ee300000 { + compatible = "renesas,sata-r8a7790"; + reg = <0 0xee300000 0 0x2000>; + interrupts = <0 105 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7790_CLK_SATA0>; + status = "disabled"; + }; + + sata1: sata@ee500000 { + compatible = "renesas,sata-r8a7790"; + reg = <0 0xee500000 0 0x2000>; + interrupts = <0 106 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7790_CLK_SATA1>; + status = "disabled"; + }; + clocks { #address-cells = <2>; #size-cells = <2>; @@ -607,10 +715,16 @@ mstp8_clks: mstp8_clks@e6150990 { compatible = "renesas,r8a7790-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe6150990 0 4>, <0 0xe61509a0 0 4>; - clocks = <&p_clk>; + clocks = <&zg_clk>, <&zg_clk>, <&zg_clk>, <&zg_clk>, <&p_clk>, + <&zs_clk>, <&zs_clk>; #clock-cells = <1>; - renesas,clock-indices = <R8A7790_CLK_ETHER>; - clock-output-names = "ether"; + renesas,clock-indices = < + R8A7790_CLK_VIN3 R8A7790_CLK_VIN2 R8A7790_CLK_VIN1 + R8A7790_CLK_VIN0 R8A7790_CLK_ETHER R8A7790_CLK_SATA1 + R8A7790_CLK_SATA0 + >; + clock-output-names = + "vin3", "vin2", "vin1", "vin0", "ether", "sata1", "sata0"; }; mstp9_clks: mstp9_clks@e6150994 { compatible = "renesas,r8a7790-mstp-clocks", "renesas,cpg-mstp-clocks"; @@ -627,4 +741,15 @@ "rcan1", "rcan0", "qspi_mod", "i2c3", "i2c2", "i2c1", "i2c0"; }; }; + + spi: spi@e6b10000 { + compatible = "renesas,qspi-r8a7790", "renesas,qspi"; + reg = <0 0xe6b10000 0 0x2c>; + interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7790_CLK_QSPI_MOD>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; }; diff --git a/arch/arm/boot/dts/r8a7791-koelsch-reference.dts b/arch/arm/boot/dts/r8a7791-koelsch-reference.dts deleted file mode 100644 index 588ca17ea1f0..000000000000 --- a/arch/arm/boot/dts/r8a7791-koelsch-reference.dts +++ /dev/null @@ -1,115 +0,0 @@ -/* - * Device Tree Source for the Koelsch board - * - * Copyright (C) 2013 Renesas Electronics Corporation - * Copyright (C) 2013 Renesas Solutions Corp. - * - * This file is licensed under the terms of the GNU General Public License - * version 2. This program is licensed "as is" without any warranty of any - * kind, whether express or implied. - */ - -/dts-v1/; -#include "r8a7791.dtsi" -#include <dt-bindings/gpio/gpio.h> - -/ { - model = "Koelsch"; - compatible = "renesas,koelsch-reference", "renesas,r8a7791"; - - chosen { - bootargs = "console=ttySC6,115200 ignore_loglevel rw root=/dev/nfs ip=dhcp"; - }; - - memory@40000000 { - device_type = "memory"; - reg = <0 0x40000000 0 0x80000000>; - }; - - lbsc { - #address-cells = <1>; - #size-cells = <1>; - }; - - gpio-keys { - compatible = "gpio-keys"; - - key-a { - gpios = <&gpio7 0 GPIO_ACTIVE_LOW>; - linux,code = <30>; - label = "SW30"; - gpio-key,wakeup; - debounce-interval = <20>; - }; - key-b { - gpios = <&gpio7 1 GPIO_ACTIVE_LOW>; - linux,code = <48>; - label = "SW31"; - gpio-key,wakeup; - debounce-interval = <20>; - }; - key-c { - gpios = <&gpio7 2 GPIO_ACTIVE_LOW>; - linux,code = <46>; - label = "SW32"; - gpio-key,wakeup; - debounce-interval = <20>; - }; - key-d { - gpios = <&gpio7 3 GPIO_ACTIVE_LOW>; - linux,code = <32>; - label = "SW33"; - gpio-key,wakeup; - debounce-interval = <20>; - }; - key-e { - gpios = <&gpio7 4 GPIO_ACTIVE_LOW>; - linux,code = <18>; - label = "SW34"; - gpio-key,wakeup; - debounce-interval = <20>; - }; - key-f { - gpios = <&gpio7 5 GPIO_ACTIVE_LOW>; - linux,code = <33>; - label = "SW35"; - gpio-key,wakeup; - debounce-interval = <20>; - }; - key-g { - gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; - linux,code = <34>; - label = "SW36"; - gpio-key,wakeup; - debounce-interval = <20>; - }; - }; - - leds { - compatible = "gpio-leds"; - led6 { - gpios = <&gpio2 19 GPIO_ACTIVE_HIGH>; - }; - led7 { - gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>; - }; - led8 { - gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; - }; - }; -}; - -&pfc { - pinctrl-0 = <&scif0_pins &scif1_pins>; - pinctrl-names = "default"; - - scif0_pins: serial0 { - renesas,groups = "scif0_data_d"; - renesas,function = "scif0"; - }; - - scif1_pins: serial1 { - renesas,groups = "scif1_data_d"; - renesas,function = "scif1"; - }; -}; diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts index fd556c3483e3..bdd73e6657b2 100644 --- a/arch/arm/boot/dts/r8a7791-koelsch.dts +++ b/arch/arm/boot/dts/r8a7791-koelsch.dts @@ -2,7 +2,8 @@ * Device Tree Source for the Koelsch board * * Copyright (C) 2013 Renesas Electronics Corporation - * Copyright (C) 2013 Renesas Solutions Corp. + * Copyright (C) 2013-2014 Renesas Solutions Corp. + * Copyright (C) 2014 Cogent Embedded, Inc. * * This file is licensed under the terms of the GNU General Public License * version 2. This program is licensed "as is" without any warranty of any @@ -23,7 +24,12 @@ memory@40000000 { device_type = "memory"; - reg = <0 0x40000000 0 0x80000000>; + reg = <0 0x40000000 0 0x40000000>; + }; + + memory@200000000 { + device_type = "memory"; + reg = <2 0x00000000 0 0x40000000>; }; lbsc { @@ -31,6 +37,60 @@ #size-cells = <1>; }; + gpio-keys { + compatible = "gpio-keys"; + + key-a { + gpios = <&gpio7 0 GPIO_ACTIVE_LOW>; + linux,code = <30>; + label = "SW30"; + gpio-key,wakeup; + debounce-interval = <20>; + }; + key-b { + gpios = <&gpio7 1 GPIO_ACTIVE_LOW>; + linux,code = <48>; + label = "SW31"; + gpio-key,wakeup; + debounce-interval = <20>; + }; + key-c { + gpios = <&gpio7 2 GPIO_ACTIVE_LOW>; + linux,code = <46>; + label = "SW32"; + gpio-key,wakeup; + debounce-interval = <20>; + }; + key-d { + gpios = <&gpio7 3 GPIO_ACTIVE_LOW>; + linux,code = <32>; + label = "SW33"; + gpio-key,wakeup; + debounce-interval = <20>; + }; + key-e { + gpios = <&gpio7 4 GPIO_ACTIVE_LOW>; + linux,code = <18>; + label = "SW34"; + gpio-key,wakeup; + debounce-interval = <20>; + }; + key-f { + gpios = <&gpio7 5 GPIO_ACTIVE_LOW>; + linux,code = <33>; + label = "SW35"; + gpio-key,wakeup; + debounce-interval = <20>; + }; + key-g { + gpios = <&gpio7 6 GPIO_ACTIVE_LOW>; + linux,code = <34>; + label = "SW36"; + gpio-key,wakeup; + debounce-interval = <20>; + }; + }; + leds { compatible = "gpio-leds"; led6 { @@ -43,16 +103,112 @@ gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>; }; }; + + vcc_sdhi0: regulator@0 { + compatible = "regulator-fixed"; + + regulator-name = "SDHI0 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio7 17 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vccq_sdhi0: regulator@1 { + compatible = "regulator-gpio"; + + regulator-name = "SDHI0 VccQ"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio2 12 GPIO_ACTIVE_HIGH>; + gpios-states = <1>; + states = <3300000 1 + 1800000 0>; + }; + + vcc_sdhi1: regulator@2 { + compatible = "regulator-fixed"; + + regulator-name = "SDHI1 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio7 18 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vccq_sdhi1: regulator@3 { + compatible = "regulator-gpio"; + + regulator-name = "SDHI1 VccQ"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio2 13 GPIO_ACTIVE_HIGH>; + gpios-states = <1>; + states = <3300000 1 + 1800000 0>; + }; + + vcc_sdhi2: regulator@4 { + compatible = "regulator-fixed"; + + regulator-name = "SDHI2 Vcc"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + + gpio = <&gpio7 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vccq_sdhi2: regulator@5 { + compatible = "regulator-gpio"; + + regulator-name = "SDHI2 VccQ"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + + gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>; + gpios-states = <1>; + states = <3300000 1 + 1800000 0>; + }; }; &extal_clk { clock-frequency = <20000000>; }; +&i2c2 { + pinctrl-0 = <&i2c2_pins>; + pinctrl-names = "default"; + + status = "okay"; + clock-frequency = <400000>; + + eeprom@50 { + compatible = "renesas,24c02"; + reg = <0x50>; + pagesize = <16>; + }; +}; + &pfc { - pinctrl-0 = <&scif0_pins &scif1_pins>; + pinctrl-0 = <&du_pins &scif0_pins &scif1_pins>; pinctrl-names = "default"; + i2c2_pins: i2c { + renesas,groups = "i2c2"; + renesas,function = "i2c2"; + }; + + du_pins: du { + renesas,groups = "du_rgb666", "du_sync", "du_clk_out_0"; + renesas,function = "du"; + }; + scif0_pins: serial0 { renesas,groups = "scif0_data_d"; renesas,function = "scif0"; @@ -62,4 +218,116 @@ renesas,groups = "scif1_data_d"; renesas,function = "scif1"; }; + + ether_pins: ether { + renesas,groups = "eth_link", "eth_mdio", "eth_rmii"; + renesas,function = "eth"; + }; + + phy1_pins: phy1 { + renesas,groups = "intc_irq0"; + renesas,function = "intc"; + }; + + sdhi0_pins: sd0 { + renesas,gpios = "sdhi0_data4", "sdhi0_ctrl"; + renesas,function = "sdhi0"; + }; + + sdhi1_pins: sd1 { + renesas,gpios = "sdhi1_data4", "sdhi1_ctrl"; + renesas,function = "sdhi1"; + }; + + sdhi2_pins: sd2 { + renesas,gpios = "sdhi2_data4", "sdhi2_ctrl"; + renesas,function = "sdhi2"; + }; + + qspi_pins: spi { + renesas,groups = "qspi_ctrl", "qspi_data4"; + renesas,function = "qspi"; + }; +}; + +ðer { + pinctrl-0 = <ðer_pins &phy1_pins>; + pinctrl-names = "default"; + + phy-handle = <&phy1>; + renesas,ether-link-active-low; + status = "ok"; + + phy1: ethernet-phy@1 { + reg = <1>; + interrupt-parent = <&irqc0>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +&sata0 { + status = "okay"; +}; + +&sdhi0 { + pinctrl-0 = <&sdhi0_pins>; + pinctrl-names = "default"; + + vmmc-supply = <&vcc_sdhi0>; + vqmmc-supply = <&vccq_sdhi0>; + cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&sdhi1 { + pinctrl-0 = <&sdhi1_pins>; + pinctrl-names = "default"; + + vmmc-supply = <&vcc_sdhi1>; + vqmmc-supply = <&vccq_sdhi1>; + cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&sdhi2 { + pinctrl-0 = <&sdhi2_pins>; + pinctrl-names = "default"; + + vmmc-supply = <&vcc_sdhi2>; + vqmmc-supply = <&vccq_sdhi2>; + cd-gpios = <&gpio6 22 GPIO_ACTIVE_LOW>; + status = "okay"; +}; + +&spi { + pinctrl-0 = <&qspi_pins>; + pinctrl-names = "default"; + + status = "okay"; + + flash: flash@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "spansion,s25fl512s"; + reg = <0>; + spi-max-frequency = <30000000>; + m25p,fast-read; + + partition@0 { + label = "loader"; + reg = <0x00000000 0x00080000>; + read-only; + }; + partition@80000 { + label = "bootenv"; + reg = <0x00080000 0x00080000>; + read-only; + }; + partition@100000 { + label = "data"; + reg = <0x00100000 0x03f00000>; + }; + }; }; diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi index 3b075dd19b51..46181708e59c 100644 --- a/arch/arm/boot/dts/r8a7791.dtsi +++ b/arch/arm/boot/dts/r8a7791.dtsi @@ -2,7 +2,8 @@ * Device Tree Source for the r8a7791 SoC * * Copyright (C) 2013 Renesas Electronics Corporation - * Copyright (C) 2013 Renesas Solutions Corp. + * Copyright (C) 2013-2014 Renesas Solutions Corp. + * Copyright (C) 2014 Cogent Embedded Inc. * * This file is licensed under the terms of the GNU General Public License * version 2. This program is licensed "as is" without any warranty of any @@ -19,6 +20,15 @@ #address-cells = <2>; #size-cells = <2>; + aliases { + i2c0 = &i2c0; + i2c1 = &i2c1; + i2c2 = &i2c2; + i2c3 = &i2c3; + i2c4 = &i2c4; + i2c5 = &i2c5; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -53,7 +63,6 @@ gpio0: gpio@e6050000 { compatible = "renesas,gpio-r8a7791", "renesas,gpio-rcar"; reg = <0 0xe6050000 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 4 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -65,7 +74,6 @@ gpio1: gpio@e6051000 { compatible = "renesas,gpio-r8a7791", "renesas,gpio-rcar"; reg = <0 0xe6051000 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 5 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -77,7 +85,6 @@ gpio2: gpio@e6052000 { compatible = "renesas,gpio-r8a7791", "renesas,gpio-rcar"; reg = <0 0xe6052000 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 6 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -89,7 +96,6 @@ gpio3: gpio@e6053000 { compatible = "renesas,gpio-r8a7791", "renesas,gpio-rcar"; reg = <0 0xe6053000 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 7 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -101,7 +107,6 @@ gpio4: gpio@e6054000 { compatible = "renesas,gpio-r8a7791", "renesas,gpio-rcar"; reg = <0 0xe6054000 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -113,7 +118,6 @@ gpio5: gpio@e6055000 { compatible = "renesas,gpio-r8a7791", "renesas,gpio-rcar"; reg = <0 0xe6055000 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 9 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -125,7 +129,6 @@ gpio6: gpio@e6055400 { compatible = "renesas,gpio-r8a7791", "renesas,gpio-rcar"; reg = <0 0xe6055400 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 10 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -137,7 +140,6 @@ gpio7: gpio@e6055800 { compatible = "renesas,gpio-r8a7791", "renesas,gpio-rcar"; reg = <0 0xe6055800 0 0x50>; - interrupt-parent = <&gic>; interrupts = <0 11 IRQ_TYPE_LEVEL_HIGH>; #gpio-cells = <2>; gpio-controller; @@ -149,8 +151,8 @@ thermal@e61f0000 { compatible = "renesas,thermal-r8a7791", "renesas,rcar-thermal"; reg = <0 0xe61f0000 0 0x14>, <0 0xe61f0100 0 0x38>; - interrupt-parent = <&gic>; interrupts = <0 69 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp5_clks R8A7791_CLK_THERMAL>; }; timer { @@ -166,7 +168,6 @@ #interrupt-cells = <2>; interrupt-controller; reg = <0 0xe61c0000 0 0x200>; - interrupt-parent = <&gic>; interrupts = <0 0 IRQ_TYPE_LEVEL_HIGH>, <0 1 IRQ_TYPE_LEVEL_HIGH>, <0 2 IRQ_TYPE_LEVEL_HIGH>, @@ -179,12 +180,288 @@ <0 17 IRQ_TYPE_LEVEL_HIGH>; }; + i2c0: i2c@e6508000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7791"; + reg = <0 0xe6508000 0 0x40>; + interrupts = <0 287 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_I2C0>; + status = "disabled"; + }; + + i2c1: i2c@e6518000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7791"; + reg = <0 0xe6518000 0 0x40>; + interrupts = <0 288 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_I2C1>; + status = "disabled"; + }; + + i2c2: i2c@e6530000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7791"; + reg = <0 0xe6530000 0 0x40>; + interrupts = <0 286 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_I2C2>; + status = "disabled"; + }; + + i2c3: i2c@e6540000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7791"; + reg = <0 0xe6540000 0 0x40>; + interrupts = <0 290 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_I2C3>; + status = "disabled"; + }; + + i2c4: i2c@e6520000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7791"; + reg = <0 0xe6520000 0 0x40>; + interrupts = <0 19 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_I2C4>; + status = "disabled"; + }; + + i2c5: i2c@e6528000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "renesas,i2c-r8a7791"; + reg = <0 0xe6528000 0 0x40>; + interrupts = <0 20 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_I2C5>; + status = "disabled"; + }; + pfc: pfc@e6060000 { compatible = "renesas,pfc-r8a7791"; reg = <0 0xe6060000 0 0x250>; #gpio-range-cells = <3>; }; + sdhi0: sd@ee100000 { + compatible = "renesas,sdhi-r8a7791"; + reg = <0 0xee100000 0 0x200>; + interrupt-parent = <&gic>; + interrupts = <0 165 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7791_CLK_SDHI0>; + status = "disabled"; + }; + + sdhi1: sd@ee140000 { + compatible = "renesas,sdhi-r8a7791"; + reg = <0 0xee140000 0 0x100>; + interrupt-parent = <&gic>; + interrupts = <0 167 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7791_CLK_SDHI1>; + status = "disabled"; + }; + + sdhi2: sd@ee160000 { + compatible = "renesas,sdhi-r8a7791"; + reg = <0 0xee160000 0 0x100>; + interrupt-parent = <&gic>; + interrupts = <0 168 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp3_clks R8A7791_CLK_SDHI2>; + status = "disabled"; + }; + + scifa0: serial@e6c40000 { + compatible = "renesas,scifa-r8a7791", "renesas,scifa"; + reg = <0 0xe6c40000 0 64>; + interrupts = <0 144 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7791_CLK_SCIFA0>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scifa1: serial@e6c50000 { + compatible = "renesas,scifa-r8a7791", "renesas,scifa"; + reg = <0 0xe6c50000 0 64>; + interrupts = <0 145 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7791_CLK_SCIFA1>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scifa2: serial@e6c60000 { + compatible = "renesas,scifa-r8a7791", "renesas,scifa"; + reg = <0 0xe6c60000 0 64>; + interrupts = <0 151 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7791_CLK_SCIFA2>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scifa3: serial@e6c70000 { + compatible = "renesas,scifa-r8a7791", "renesas,scifa"; + reg = <0 0xe6c70000 0 64>; + interrupts = <0 29 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp11_clks R8A7791_CLK_SCIFA3>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scifa4: serial@e6c78000 { + compatible = "renesas,scifa-r8a7791", "renesas,scifa"; + reg = <0 0xe6c78000 0 64>; + interrupts = <0 30 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp11_clks R8A7791_CLK_SCIFA4>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scifa5: serial@e6c80000 { + compatible = "renesas,scifa-r8a7791", "renesas,scifa"; + reg = <0 0xe6c80000 0 64>; + interrupts = <0 31 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp11_clks R8A7791_CLK_SCIFA5>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scifb0: serial@e6c20000 { + compatible = "renesas,scifb-r8a7791", "renesas,scifb"; + reg = <0 0xe6c20000 0 64>; + interrupts = <0 148 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7791_CLK_SCIFB0>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scifb1: serial@e6c30000 { + compatible = "renesas,scifb-r8a7791", "renesas,scifb"; + reg = <0 0xe6c30000 0 64>; + interrupts = <0 149 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7791_CLK_SCIFB1>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scifb2: serial@e6ce0000 { + compatible = "renesas,scifb-r8a7791", "renesas,scifb"; + reg = <0 0xe6ce0000 0 64>; + interrupts = <0 150 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp2_clks R8A7791_CLK_SCIFB2>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scif0: serial@e6e60000 { + compatible = "renesas,scif-r8a7791", "renesas,scif"; + reg = <0 0xe6e60000 0 64>; + interrupts = <0 152 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7791_CLK_SCIF0>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scif1: serial@e6e68000 { + compatible = "renesas,scif-r8a7791", "renesas,scif"; + reg = <0 0xe6e68000 0 64>; + interrupts = <0 153 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7791_CLK_SCIF1>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scif2: serial@e6e58000 { + compatible = "renesas,scif-r8a7791", "renesas,scif"; + reg = <0 0xe6e58000 0 64>; + interrupts = <0 22 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7791_CLK_SCIF2>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scif3: serial@e6ea8000 { + compatible = "renesas,scif-r8a7791", "renesas,scif"; + reg = <0 0xe6ea8000 0 64>; + interrupts = <0 23 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7791_CLK_SCIF3>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scif4: serial@e6ee0000 { + compatible = "renesas,scif-r8a7791", "renesas,scif"; + reg = <0 0xe6ee0000 0 64>; + interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7791_CLK_SCIF4>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + scif5: serial@e6ee8000 { + compatible = "renesas,scif-r8a7791", "renesas,scif"; + reg = <0 0xe6ee8000 0 64>; + interrupts = <0 25 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7791_CLK_SCIF5>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + hscif0: serial@e62c0000 { + compatible = "renesas,hscif-r8a7791", "renesas,hscif"; + reg = <0 0xe62c0000 0 96>; + interrupts = <0 154 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7791_CLK_HSCIF0>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + hscif1: serial@e62c8000 { + compatible = "renesas,hscif-r8a7791", "renesas,hscif"; + reg = <0 0xe62c8000 0 96>; + interrupts = <0 155 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7791_CLK_HSCIF1>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + hscif2: serial@e62d0000 { + compatible = "renesas,hscif-r8a7791", "renesas,hscif"; + reg = <0 0xe62d0000 0 96>; + interrupts = <0 21 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp7_clks R8A7791_CLK_HSCIF2>; + clock-names = "sci_ick"; + status = "disabled"; + }; + + ether: ethernet@ee700000 { + compatible = "renesas,ether-r8a7791"; + reg = <0 0xee700000 0 0x400>; + interrupts = <0 162 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7791_CLK_ETHER>; + phy-mode = "rmii"; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + sata0: sata@ee300000 { + compatible = "renesas,sata-r8a7791"; + reg = <0 0xee300000 0 0x2000>; + interrupts = <0 105 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7791_CLK_SATA0>; + status = "disabled"; + }; + + sata1: sata@ee500000 { + compatible = "renesas,sata-r8a7791"; + reg = <0 0xee500000 0 0x2000>; + interrupts = <0 106 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp8_clks R8A7791_CLK_SATA1>; + status = "disabled"; + }; + clocks { #address-cells = <2>; #size-cells = <2>; @@ -474,10 +751,15 @@ mstp8_clks: mstp8_clks@e6150990 { compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks"; reg = <0 0xe6150990 0 4>, <0 0xe61509a0 0 4>; - clocks = <&p_clk>; + clocks = <&zg_clk>, <&zg_clk>, <&zg_clk>, <&p_clk>, <&zs_clk>, + <&zs_clk>; #clock-cells = <1>; - renesas,clock-indices = <R8A7791_CLK_ETHER>; - clock-output-names = "ether"; + renesas,clock-indices = < + R8A7791_CLK_VIN2 R8A7791_CLK_VIN1 R8A7791_CLK_VIN0 + R8A7791_CLK_ETHER R8A7791_CLK_SATA1 R8A7791_CLK_SATA0 + >; + clock-output-names = + "vin2", "vin1", "vin0", "ether", "sata1", "sata0"; }; mstp9_clks: mstp9_clks@e6150994 { compatible = "renesas,r8a7791-mstp-clocks", "renesas,cpg-mstp-clocks"; @@ -488,7 +770,7 @@ #clock-cells = <1>; renesas,clock-indices = < R8A7791_CLK_RCAN1 R8A7791_CLK_RCAN0 R8A7791_CLK_QSPI_MOD - R8A7791_CLK_I2C4 R8A7791_CLK_I2C4 R8A7791_CLK_I2C3 + R8A7791_CLK_I2C5 R8A7791_CLK_I2C4 R8A7791_CLK_I2C3 R8A7791_CLK_I2C2 R8A7791_CLK_I2C1 R8A7791_CLK_I2C0 >; clock-output-names = @@ -506,4 +788,15 @@ clock-output-names = "scifa3", "scifa4", "scifa5"; }; }; + + spi: spi@e6b10000 { + compatible = "renesas,qspi-r8a7791", "renesas,qspi"; + reg = <0 0xe6b10000 0 0x2c>; + interrupts = <0 184 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&mstp9_clks R8A7791_CLK_QSPI_MOD>; + num-cs = <1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; }; diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi index 3d5faf85f51b..eabcfdbb403a 100644 --- a/arch/arm/boot/dts/sama5d3.dtsi +++ b/arch/arm/boot/dts/sama5d3.dtsi @@ -239,7 +239,9 @@ }; adc0: adc@f8018000 { - compatible = "atmel,at91sam9260-adc"; + #address-cells = <1>; + #size-cells = <0>; + compatible = "atmel,at91sam9x5-adc"; reg = <0xf8018000 0x100>; interrupts = <29 IRQ_TYPE_LEVEL_HIGH 5>; pinctrl-names = "default"; @@ -261,52 +263,39 @@ clocks = <&adc_clk>, <&adc_op_clk>; clock-names = "adc_clk", "adc_op_clk"; - atmel,adc-channel-base = <0x50>; atmel,adc-channels-used = <0xfff>; - atmel,adc-drdy-mask = <0x1000000>; - atmel,adc-num-channels = <12>; atmel,adc-startup-time = <40>; - atmel,adc-status-register = <0x30>; - atmel,adc-trigger-register = <0xc0>; - atmel,adc-use-external; + atmel,adc-use-external-triggers; atmel,adc-vref = <3000>; atmel,adc-res = <10 12>; atmel,adc-res-names = "lowres", "highres"; status = "disabled"; trigger@0 { + reg = <0>; trigger-name = "external-rising"; trigger-value = <0x1>; trigger-external; }; trigger@1 { + reg = <1>; trigger-name = "external-falling"; trigger-value = <0x2>; trigger-external; }; trigger@2 { + reg = <2>; trigger-name = "external-any"; trigger-value = <0x3>; trigger-external; }; trigger@3 { + reg = <3>; trigger-name = "continuous"; trigger-value = <0x6>; }; }; - tsadcc: tsadcc@f8018000 { - compatible = "atmel,at91sam9x5-tsadcc"; - reg = <0xf8018000 0x4000>; - interrupts = <29 IRQ_TYPE_LEVEL_HIGH 5>; - atmel,tsadcc_clock = <300000>; - atmel,filtering_average = <0x03>; - atmel,pendet_debounce = <0x08>; - atmel,pendet_sensitivity = <0x02>; - atmel,ts_sample_hold_time = <0x0a>; - status = "disabled"; - }; - i2c2: i2c@f801c000 { compatible = "atmel,at91sam9x5-i2c"; reg = <0xf801c000 0x4000>; @@ -1256,6 +1245,7 @@ interrupts = <5 IRQ_TYPE_LEVEL_HIGH 6>; atmel,nand-addr-offset = <21>; atmel,nand-cmd-offset = <22>; + atmel,nand-has-dma; pinctrl-names = "default"; pinctrl-0 = <&pinctrl_nand0_ale_cle>; atmel,pmecc-lookup-table-offset = <0x0 0x8000>; diff --git a/arch/arm/boot/dts/sama5d3xdm.dtsi b/arch/arm/boot/dts/sama5d3xdm.dtsi index f9bdde542ced..035ab72b3990 100644 --- a/arch/arm/boot/dts/sama5d3xdm.dtsi +++ b/arch/arm/boot/dts/sama5d3xdm.dtsi @@ -23,10 +23,8 @@ }; adc0: adc@f8018000 { - status = "disabled"; - }; - - tsadcc: tsadcc@f8018000 { + atmel,adc-ts-wires = <4>; + atmel,adc-ts-pressure-threshold = <10000>; status = "okay"; }; diff --git a/arch/arm/boot/dts/socfpga.dtsi b/arch/arm/boot/dts/socfpga.dtsi index 537f1a5c07f5..ba51d69abbea 100644 --- a/arch/arm/boot/dts/socfpga.dtsi +++ b/arch/arm/boot/dts/socfpga.dtsi @@ -443,6 +443,7 @@ gmac0: ethernet@ff700000 { compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; + altr,sysmgr-syscon = <&sysmgr 0x60 0>; reg = <0xff700000 0x2000>; interrupts = <0 115 4>; interrupt-names = "macirq"; @@ -454,6 +455,7 @@ gmac1: ethernet@ff702000 { compatible = "altr,socfpga-stmmac", "snps,dwmac-3.70a", "snps,dwmac"; + altr,sysmgr-syscon = <&sysmgr 0x60 2>; reg = <0xff702000 0x2000>; interrupts = <0 120 4>; interrupt-names = "macirq"; diff --git a/arch/arm/boot/dts/socfpga_arria5_socdk.dts b/arch/arm/boot/dts/socfpga_arria5_socdk.dts index 5beffb2265f4..a87ee1c07661 100644 --- a/arch/arm/boot/dts/socfpga_arria5_socdk.dts +++ b/arch/arm/boot/dts/socfpga_arria5_socdk.dts @@ -37,4 +37,25 @@ */ ethernet0 = &gmac1; }; + + aliases { + /* this allow the ethaddr uboot environmnet variable contents + * to be added to the gmac1 device tree blob. + */ + ethernet0 = &gmac1; + }; +}; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txen-skew-ps = <0>; + txc-skew-ps = <2600>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <2000>; }; diff --git a/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts b/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts index 2ee52ab8cabb..ae16d975196d 100644 --- a/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts +++ b/arch/arm/boot/dts/socfpga_cyclone5_socdk.dts @@ -38,3 +38,17 @@ ethernet0 = &gmac1; }; }; + +&gmac1 { + status = "okay"; + phy-mode = "rgmii"; + + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txen-skew-ps = <0>; + txc-skew-ps = <2600>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <2000>; +}; diff --git a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts index 50b99a2c12ae..b79e2a2bf175 100644 --- a/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts +++ b/arch/arm/boot/dts/socfpga_cyclone5_sockit.dts @@ -30,8 +30,25 @@ device_type = "memory"; reg = <0x0 0x40000000>; /* 1GB */ }; + + aliases { + /* this allow the ethaddr uboot environmnet variable contents + * to be added to the gmac1 device tree blob. + */ + ethernet0 = &gmac1; + }; }; &gmac1 { status = "okay"; + phy-mode = "rgmii"; + + rxd0-skew-ps = <0>; + rxd1-skew-ps = <0>; + rxd2-skew-ps = <0>; + rxd3-skew-ps = <0>; + txen-skew-ps = <0>; + txc-skew-ps = <2600>; + rxdv-skew-ps = <0>; + rxc-skew-ps = <2000>; }; diff --git a/arch/arm/boot/dts/socfpga_vt.dts b/arch/arm/boot/dts/socfpga_vt.dts index d1ec0cab2dee..dde2c66c50eb 100644 --- a/arch/arm/boot/dts/socfpga_vt.dts +++ b/arch/arm/boot/dts/socfpga_vt.dts @@ -75,3 +75,8 @@ }; }; }; + +&gmac0 { + status = "okay"; + phy-mode = "gmii"; +}; diff --git a/arch/arm/boot/dts/ste-dbx5x0.dtsi b/arch/arm/boot/dts/ste-dbx5x0.dtsi index e0853ea02df2..e41eedca3ce3 100644 --- a/arch/arm/boot/dts/ste-dbx5x0.dtsi +++ b/arch/arm/boot/dts/ste-dbx5x0.dtsi @@ -705,7 +705,7 @@ #address-cells = <1>; #size-cells = <0>; clocks = <&prcc_kclk 3 1>, <&prcc_pclk 3 1>; - clock-names = "ssp0clk", "apb_pclk"; + clock-names = "SSPCLK", "apb_pclk"; dmas = <&dma 8 0 0x2>, /* Logical - DevToMem */ <&dma 8 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "tx"; @@ -718,7 +718,7 @@ #address-cells = <1>; #size-cells = <0>; clocks = <&prcc_kclk 3 2>, <&prcc_pclk 3 2>; - clock-names = "ssp1clk", "apb_pclk"; + clock-names = "SSPCLK", "apb_pclk"; dmas = <&dma 9 0 0x2>, /* Logical - DevToMem */ <&dma 9 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "tx"; @@ -732,7 +732,7 @@ #size-cells = <0>; /* Same clock wired to kernel and pclk */ clocks = <&prcc_pclk 2 8>, <&prcc_pclk 2 8>; - clock-names = "spi0clk", "apb_pclk"; + clock-names = "SSPCLK", "apb_pclk"; dmas = <&dma 0 0 0x2>, /* Logical - DevToMem */ <&dma 0 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "tx"; @@ -746,7 +746,7 @@ #size-cells = <0>; /* Same clock wired to kernel and pclk */ clocks = <&prcc_pclk 2 2>, <&prcc_pclk 2 2>; - clock-names = "spi1clk", "apb_pclk"; + clock-names = "SSPCLK", "apb_pclk"; dmas = <&dma 35 0 0x2>, /* Logical - DevToMem */ <&dma 35 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "tx"; @@ -760,7 +760,7 @@ #size-cells = <0>; /* Same clock wired to kernel and pclk */ clocks = <&prcc_pclk 2 1>, <&prcc_pclk 2 1>; - clock-names = "spi2clk", "apb_pclk"; + clock-names = "SSPCLK", "apb_pclk"; dmas = <&dma 33 0 0x2>, /* Logical - DevToMem */ <&dma 33 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "tx"; @@ -774,7 +774,7 @@ #size-cells = <0>; /* Same clock wired to kernel and pclk */ clocks = <&prcc_pclk 1 7>, <&prcc_pclk 1 7>; - clock-names = "spi3clk", "apb_pclk"; + clock-names = "SSPCLK", "apb_pclk"; dmas = <&dma 40 0 0x2>, /* Logical - DevToMem */ <&dma 40 0 0x0>; /* Logical - MemToDev */ dma-names = "rx", "tx"; diff --git a/arch/arm/boot/dts/ste-href-ab8500.dtsi b/arch/arm/boot/dts/ste-href-ab8500.dtsi new file mode 100644 index 000000000000..30f8601da323 --- /dev/null +++ b/arch/arm/boot/dts/ste-href-ab8500.dtsi @@ -0,0 +1,428 @@ +/* + * Copyright 2014 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/ { + soc { + prcmu@80157000 { + ab8500 { + ab8500-gpio { + /* Hog a few default settings */ + pinctrl-names = "default"; + pinctrl-0 = <&gpio2_default_mode>, + <&gpio4_default_mode>, + <&gpio10_default_mode>, + <&gpio11_default_mode>, + <&gpio12_default_mode>, + <&gpio13_default_mode>, + <&gpio16_default_mode>, + <&gpio24_default_mode>, + <&gpio25_default_mode>, + <&gpio36_default_mode>, + <&gpio37_default_mode>, + <&gpio38_default_mode>, + <&gpio39_default_mode>, + <&gpio42_default_mode>, + <&gpio26_default_mode>, + <&gpio35_default_mode>, + <&ycbcr_default_mode>, + <&pwm_default_mode>, + <&adi1_default_mode>, + <&usbuicc_default_mode>, + <&dmic_default_mode>, + <&extcpena_default_mode>, + <&modsclsda_default_mode>; + + /* + * Pins 2, 4, 10, 11, 12, 13, 16, 24, 25, 36, 37, 38, 39 and 42 + * are muxed in as GPIO, and configured as INPUT PULL DOWN + */ + gpio2 { + gpio2_default_mode: gpio2_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio2_a_1"; + }; + default_cfg { + ste,pins = "GPIO2_T9"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio4 { + gpio4_default_mode: gpio4_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio4_a_1"; + }; + default_cfg { + ste,pins = "GPIO4_W2"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio10 { + gpio10_default_mode: gpio10_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio10_d_1"; + }; + default_cfg { + ste,pins = "GPIO10_U17"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio11 { + gpio11_default_mode: gpio11_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio11_d_1"; + }; + default_cfg { + ste,pins = "GPIO11_AA18"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio12 { + gpio12_default_mode: gpio12_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio12_d_1"; + }; + default_cfg { + ste,pins = "GPIO12_U16"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio13 { + gpio13_default_mode: gpio13_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio13_d_1"; + }; + default_cfg { + ste,pins = "GPIO13_W17"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio16 { + gpio16_default_mode: gpio16_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio16_a_1"; + }; + default_cfg { + ste,pins = "GPIO16_F15"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio24 { + gpio24_default_mode: gpio24_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio24_a_1"; + }; + default_cfg { + ste,pins = "GPIO24_T14"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio25 { + gpio25_default_mode: gpio25_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio25_a_1"; + }; + default_cfg { + ste,pins = "GPIO25_R16"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio36 { + gpio36_default_mode: gpio36_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio36_a_1"; + }; + default_cfg { + ste,pins = "GPIO36_A17"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio37 { + gpio37_default_mode: gpio37_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio37_a_1"; + }; + default_cfg { + ste,pins = "GPIO37_E15"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio38 { + gpio38_default_mode: gpio38_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio38_a_1"; + }; + default_cfg { + ste,pins = "GPIO38_C17"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio39 { + gpio39_default_mode: gpio39_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio39_a_1"; + }; + default_cfg { + ste,pins = "GPIO39_E16"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio42 { + gpio42_default_mode: gpio42_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio42_a_1"; + }; + default_cfg { + ste,pins = "GPIO42_U2"; + input-enable; + bias-pull-down; + }; + }; + }; + /* + * Pins 26 and 35 muxed in as GPIO, and configured as OUTPUT LOW + */ + gpio26 { + gpio26_default_mode: gpio26_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio26_d_1"; + }; + default_cfg { + ste,pins = "GPIO26_M16"; + output-low; + }; + }; + }; + gpio35 { + gpio35_default_mode: gpio35_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio35_d_1"; + }; + default_cfg { + ste,pins = "GPIO35_W15"; + output-low; + }; + }; + }; + /* + * This sets up the YCBCR connector pins, i.e. analog video out. + * Set as input with no bias. + */ + ycbcr { + ycbcr_default_mode: ycbcr_default { + default_mux { + ste,function = "ycbcr"; + ste,pins = "ycbcr0123_d_1"; + }; + default_cfg { + ste,pins = "GPIO6_Y18", + "GPIO7_AA20", + "GPIO8_W18", + "GPIO9_AA19"; + input-enable; + bias-disable; + }; + }; + }; + /* This sets up the PWM pins 14 and 15 */ + pwm { + pwm_default_mode: pwm_default { + default_mux { + ste,function = "pwmout"; + ste,pins = "pwmout1_d_1", "pwmout2_d_1"; + }; + default_cfg { + ste,pins = "GPIO14_F14", + "GPIO15_B17"; + input-enable; + bias-pull-down; + }; + }; + }; + /* This sets up audio interface 1 */ + adi1 { + adi1_default_mode: adi1_default { + default_mux { + ste,function = "adi1"; + ste,pins = "adi1_d_1"; + }; + default_cfg { + ste,pins = "GPIO17_P5", + "GPIO18_R5", + "GPIO19_U5", + "GPIO20_T5"; + input-enable; + bias-pull-down; + }; + }; + }; + /* This sets up the USB UICC pins */ + usbuicc { + usbuicc_default_mode: usbuicc_default { + default_mux { + ste,function = "usbuicc"; + ste,pins = "usbuicc_d_1"; + }; + default_cfg { + ste,pins = "GPIO21_H19", + "GPIO22_G20", + "GPIO23_G19"; + input-enable; + bias-pull-down; + }; + }; + }; + /* This sets up the microphone pins */ + dmic { + dmic_default_mode: dmic_default { + default_mux { + ste,function = "dmic"; + ste,pins = "dmic12_d_1", + "dmic34_d_1", + "dmic56_d_1"; + }; + default_cfg { + ste,pins = "GPIO27_J6", + "GPIO28_K6", + "GPIO29_G6", + "GPIO30_H6", + "GPIO31_F5", + "GPIO32_G5"; + input-enable; + bias-pull-down; + }; + }; + }; + extcpena { + extcpena_default_mode: extcpena_default { + default_mux { + ste,function = "extcpena"; + ste,pins = "extcpena_d_1"; + }; + default_cfg { + ste,pins = "GPIO34_R17"; + input-enable; + bias-pull-down; + }; + }; + }; + /* Modem I2C setup (SCL and SDA pins) */ + modsclsda { + modsclsda_default_mode: modsclsda_default { + default_mux { + ste,function = "modsclsda"; + ste,pins = "modsclsda_d_1"; + }; + default_cfg { + ste,pins = "GPIO40_T19", + "GPIO41_U19"; + input-enable; + bias-pull-down; + }; + }; + }; + /* + * Clock output pins associated with regulators. + */ + sysclkreq2 { + sysclkreq2_default_mode: sysclkreq2_default { + default_mux { + ste,function = "sysclkreq"; + ste,pins = "sysclkreq2_d_1"; + }; + default_cfg { + ste,pins = "GPIO1_T10"; + input-enable; + bias-disable; + }; + }; + sysclkreq2_sleep_mode: sysclkreq2_sleep { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio1_a_1"; + }; + default_cfg { + ste,pins = "GPIO1_T10"; + input-enable; + bias-pull-down; + }; + }; + }; + sysclkreq4 { + sysclkreq4_default_mode: sysclkreq4_default { + default_mux { + ste,function = "sysclkreq"; + ste,pins = "sysclkreq4_d_1"; + }; + default_cfg { + ste,pins = "GPIO3_U9"; + input-enable; + bias-disable; + }; + }; + sysclkreq4_sleep_mode: sysclkreq4_sleep { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio3_a_1"; + }; + default_cfg { + ste,pins = "GPIO3_U9"; + input-enable; + bias-pull-down; + }; + }; + }; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/ste-href-ab8505.dtsi b/arch/arm/boot/dts/ste-href-ab8505.dtsi new file mode 100644 index 000000000000..6006d62086a2 --- /dev/null +++ b/arch/arm/boot/dts/ste-href-ab8505.dtsi @@ -0,0 +1,240 @@ +/* + * Copyright 2014 Linaro Ltd. + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/ { + soc { + prcmu@80157000 { + ab8505 { + ab8505-gpio { + /* Hog a few default settings */ + pinctrl-names = "default"; + pinctrl-0 = <&gpio2_default_mode>, + <&gpio10_default_mode>, + <&gpio11_default_mode>, + <&gpio13_default_mode>, + <&gpio34_default_mode>, + <&gpio50_default_mode>, + <&pwm_default_mode>, + <&adi2_default_mode>, + <&modsclsda_default_mode>, + <&resethw_default_mode>, + <&service_default_mode>; + + /* + * Pins 2, 10, 11, 13, 34 and 50 + * are muxed in as GPIO, and configured as INPUT PULL DOWN + */ + gpio2 { + gpio2_default_mode: gpio2_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio2_a_1"; + }; + default_cfg { + ste,pins = "GPIO2_R5"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio10 { + gpio10_default_mode: gpio10_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio10_d_1"; + }; + default_cfg { + ste,pins = "GPIO10_B16"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio11 { + gpio11_default_mode: gpio11_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio11_d_1"; + }; + default_cfg { + ste,pins = "GPIO11_B17"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio13 { + gpio13_default_mode: gpio13_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio13_d_1"; + }; + default_cfg { + ste,pins = "GPIO13_D17"; + input-enable; + bias-disable; + }; + }; + }; + gpio34 { + gpio34_default_mode: gpio34_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio34_a_1"; + }; + default_cfg { + ste,pins = "GPIO34_H14"; + input-enable; + bias-pull-down; + }; + }; + }; + gpio50 { + gpio50_default_mode: gpio50_default { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio50_d_1"; + }; + default_cfg { + ste,pins = "GPIO50_L4"; + input-enable; + bias-disable; + }; + }; + }; + /* This sets up the PWM pin 14 */ + pwm { + pwm_default_mode: pwm_default { + default_mux { + ste,function = "pwmout"; + ste,pins = "pwmout1_d_1"; + }; + default_cfg { + ste,pins = "GPIO14_C16"; + input-enable; + bias-pull-down; + }; + }; + }; + /* This sets up audio interface 2 */ + adi2 { + adi2_default_mode: adi2_default { + default_mux { + ste,function = "adi2"; + ste,pins = "adi2_d_1"; + }; + default_cfg { + ste,pins = "GPIO17_P2", + "GPIO18_N3", + "GPIO19_T1", + "GPIO20_P3"; + input-enable; + bias-pull-down; + }; + }; + }; + /* Modem I2C setup (SCL and SDA pins) */ + modsclsda { + modsclsda_default_mode: modsclsda_default { + default_mux { + ste,function = "modsclsda"; + ste,pins = "modsclsda_d_1"; + }; + default_cfg { + ste,pins = "GPIO40_J15", + "GPIO41_J14"; + input-enable; + bias-pull-down; + }; + }; + }; + resethw { + resethw_default_mode: resethw_default { + default_mux { + ste,function = "resethw"; + ste,pins = "resethw_d_1"; + }; + default_cfg { + ste,pins = "GPIO52_D16"; + input-enable; + bias-pull-down; + }; + }; + }; + service { + service_default_mode: service_default { + default_mux { + ste,function = "service"; + ste,pins = "service_d_1"; + }; + default_cfg { + ste,pins = "GPIO53_D15"; + input-enable; + bias-pull-down; + }; + }; + }; + /* + * Clock output pins associated with regulators. + */ + sysclkreq2 { + sysclkreq2_default_mode: sysclkreq2_default { + default_mux { + ste,function = "sysclkreq"; + ste,pins = "sysclkreq2_d_1"; + }; + default_cfg { + ste,pins = "GPIO1_N4"; + input-enable; + bias-disable; + }; + }; + sysclkreq2_sleep_mode: sysclkreq2_sleep { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio1_a_1"; + }; + default_cfg { + ste,pins = "GPIO1_N4"; + input-enable; + bias-pull-down; + }; + }; + }; + sysclkreq4 { + sysclkreq4_default_mode: sysclkreq4_default { + default_mux { + ste,function = "sysclkreq"; + ste,pins = "sysclkreq4_d_1"; + }; + default_cfg { + ste,pins = "GPIO3_P5"; + input-enable; + bias-disable; + }; + }; + sysclkreq4_sleep_mode: sysclkreq4_sleep { + default_mux { + ste,function = "gpio"; + ste,pins = "gpio3_a_1"; + }; + default_cfg { + ste,pins = "GPIO3_P5"; + input-enable; + bias-pull-down; + }; + }; + }; + }; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/ste-hrefprev60.dtsi b/arch/arm/boot/dts/ste-hrefprev60.dtsi index 40f0ecdf9303..abc762e24fcb 100644 --- a/arch/arm/boot/dts/ste-hrefprev60.dtsi +++ b/arch/arm/boot/dts/ste-hrefprev60.dtsi @@ -12,6 +12,7 @@ */ #include "ste-dbx5x0.dtsi" +#include "ste-href-ab8500.dtsi" #include "ste-href.dtsi" / { diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi index 3b6d1181939b..c2341061b943 100644 --- a/arch/arm/boot/dts/ste-hrefv60plus.dtsi +++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi @@ -10,6 +10,7 @@ */ #include "ste-dbx5x0.dtsi" +#include "ste-href-ab8500.dtsi" #include "ste-href.dtsi" / { diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts index 97d5d21b7db7..a2f632d0be2a 100644 --- a/arch/arm/boot/dts/ste-snowball.dts +++ b/arch/arm/boot/dts/ste-snowball.dts @@ -11,6 +11,7 @@ /dts-v1/; #include "ste-dbx5x0.dtsi" +#include "ste-href-ab8500.dtsi" #include "ste-href-family-pinctrl.dtsi" / { diff --git a/arch/arm/boot/dts/ste-u300.dts b/arch/arm/boot/dts/ste-u300.dts index a9da4800daf0..6fe688e9e4da 100644 --- a/arch/arm/boot/dts/ste-u300.dts +++ b/arch/arm/boot/dts/ste-u300.dts @@ -457,7 +457,7 @@ interrupt-parent = <&vica>; interrupts = <23>; clocks = <&spi_clk>, <&spi_clk>; - clock-names = "apb_pclk", "spi_clk"; + clock-names = "SSPCLK", "apb_pclk"; dmas = <&dmac 27 &dmac 28>; dma-names = "tx", "rx"; num-cs = <3>; diff --git a/arch/arm/boot/dts/stih415-clock.dtsi b/arch/arm/boot/dts/stih415-clock.dtsi index 174c799df741..d047dbc28d61 100644 --- a/arch/arm/boot/dts/stih415-clock.dtsi +++ b/arch/arm/boot/dts/stih415-clock.dtsi @@ -34,5 +34,19 @@ compatible = "fixed-clock"; clock-frequency = <100000000>; }; + + CLKS_GMAC0_PHY: clockgenA1@7 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + clock-output-names = "CLKS_GMAC0_PHY"; + }; + + CLKS_ETH1_PHY: clockgenA0@7 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + clock-output-names = "CLKS_ETH1_PHY"; + }; }; }; diff --git a/arch/arm/boot/dts/stih415-pinctrl.dtsi b/arch/arm/boot/dts/stih415-pinctrl.dtsi index e56449d41481..f09fb10a3791 100644 --- a/arch/arm/boot/dts/stih415-pinctrl.dtsi +++ b/arch/arm/boot/dts/stih415-pinctrl.dtsi @@ -7,6 +7,7 @@ * publishhed by the Free Software Foundation. */ #include "st-pincfg.h" +#include <dt-bindings/interrupt-controller/arm-gic.h> / { aliases { @@ -45,35 +46,49 @@ #size-cells = <1>; compatible = "st,stih415-sbc-pinctrl"; st,syscfg = <&syscfg_sbc>; + reg = <0xfe61f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 180 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfe610000 0x5000>; PIO0: gpio@fe610000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO0"; }; PIO1: gpio@fe611000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO1"; }; PIO2: gpio@fe612000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO2"; }; PIO3: gpio@fe613000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO3"; }; PIO4: gpio@fe614000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO4"; }; @@ -104,6 +119,64 @@ }; }; }; + + rc{ + pinctrl_ir: ir0 { + st,pins { + ir = <&PIO4 0 ALT2 IN>; + }; + }; + }; + + gmac1 { + pinctrl_mii1: mii1 { + st,pins { + txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>; + col = <&PIO0 7 ALT1 IN BYPASS 1000>; + mdio = <&PIO1 0 ALT1 OUT BYPASS 0>; + mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>; + crs = <&PIO1 2 ALT1 IN BYPASS 1000>; + mdint = <&PIO1 3 ALT1 IN BYPASS 0>; + rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>; + phyclk = <&PIO2 3 ALT1 IN NICLK 1000 CLK_A>; + }; + }; + + pinctrl_rgmii1: rgmii1-0 { + st,pins { + txd0 = <&PIO0 0 ALT1 OUT DE_IO 1000 CLK_A>; + txd1 = <&PIO0 1 ALT1 OUT DE_IO 1000 CLK_A>; + txd2 = <&PIO0 2 ALT1 OUT DE_IO 1000 CLK_A>; + txd3 = <&PIO0 3 ALT1 OUT DE_IO 1000 CLK_A>; + txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>; + txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>; + mdio = <&PIO1 0 ALT1 OUT BYPASS 0>; + mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>; + rxd0 = <&PIO1 4 ALT1 IN DE_IO 0 CLK_A>; + rxd1 = <&PIO1 5 ALT1 IN DE_IO 0 CLK_A>; + rxd2 = <&PIO1 6 ALT1 IN DE_IO 0 CLK_A>; + rxd3 = <&PIO1 7 ALT1 IN DE_IO 0 CLK_A>; + + rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>; + rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>; + phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>; + + clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>; + }; + }; + }; }; pin-controller-front { @@ -111,53 +184,73 @@ #size-cells = <1>; compatible = "st,stih415-front-pinctrl"; st,syscfg = <&syscfg_front>; + reg = <0xfee0f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 181 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfee00000 0x8000>; PIO5: gpio@fee00000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO5"; }; PIO6: gpio@fee01000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO6"; }; PIO7: gpio@fee02000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO7"; }; PIO8: gpio@fee03000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO8"; }; PIO9: gpio@fee04000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO9"; }; PIO10: gpio@fee05000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x5000 0x100>; st,bank-name = "PIO10"; }; PIO11: gpio@fee06000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x6000 0x100>; st,bank-name = "PIO11"; }; PIO12: gpio@fee07000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x7000 0x100>; st,bank-name = "PIO12"; }; @@ -186,41 +279,57 @@ #size-cells = <1>; compatible = "st,stih415-rear-pinctrl"; st,syscfg = <&syscfg_rear>; + reg = <0xfe82f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfe820000 0x8000>; PIO13: gpio@fe820000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO13"; }; PIO14: gpio@fe821000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO14"; }; PIO15: gpio@fe822000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO15"; }; PIO16: gpio@fe823000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO16"; }; PIO17: gpio@fe824000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO17"; }; PIO18: gpio@fe825000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x5000 0x100>; st,bank-name = "PIO18"; }; @@ -233,6 +342,77 @@ }; }; }; + + gmac0{ + pinctrl_mii0: mii0 { + st,pins { + mdint = <&PIO13 6 ALT2 IN BYPASS 0>; + txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + + txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>; + txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>; + + txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>; + txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + crs = <&PIO15 2 ALT2 IN BYPASS 1000>; + col = <&PIO15 3 ALT2 IN BYPASS 1000>; + mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>; + mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>; + + rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>; + phyclk = <&PIO13 5 ALT2 OUT NICLK 1000 CLK_A>; + + }; + }; + + pinctrl_gmii0: gmii0 { + st,pins { + mdint = <&PIO13 6 ALT2 IN BYPASS 0>; + mdio = <&PIO15 4 ALT2 OUT BYPASS 3000>; + mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>; + txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 3000 CLK_A>; + + txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 3000 CLK_A>; + txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>; + txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 3000 CLK_B>; + txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 3000 CLK_B>; + txd4 = <&PIO14 4 ALT2 OUT SE_NICLK_IO 3000 CLK_B>; + txd5 = <&PIO14 5 ALT2 OUT SE_NICLK_IO 3000 CLK_B>; + txd6 = <&PIO14 6 ALT2 OUT SE_NICLK_IO 3000 CLK_B>; + txd7 = <&PIO14 7 ALT2 OUT SE_NICLK_IO 3000 CLK_B>; + + txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>; + txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 3000 CLK_A>; + crs = <&PIO15 2 ALT2 IN BYPASS 1000>; + col = <&PIO15 3 ALT2 IN BYPASS 1000>; + rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + + rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd4 = <&PIO16 4 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd5 = <&PIO16 5 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd6 = <&PIO16 6 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + rxd7 = <&PIO16 7 ALT2 IN SE_NICLK_IO 1500 CLK_A>; + + rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>; + clk125 = <&PIO17 6 ALT1 IN NICLK 0 CLK_A>; + phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>; + + + }; + }; + }; }; pin-controller-left { @@ -240,23 +420,33 @@ #size-cells = <1>; compatible = "st,stih415-left-pinctrl"; st,syscfg = <&syscfg_left>; + reg = <0xfd6bf080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfd6b0000 0x3000>; PIO100: gpio@fd6b0000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO100"; }; PIO101: gpio@fd6b1000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO101"; }; PIO102: gpio@fd6b2000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO102"; }; @@ -267,35 +457,49 @@ #size-cells = <1>; compatible = "st,stih415-right-pinctrl"; st,syscfg = <&syscfg_right>; + reg = <0xfd33f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfd330000 0x5000>; PIO103: gpio@fd330000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO103"; }; PIO104: gpio@fd331000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO104"; }; PIO105: gpio@fd332000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO105"; }; PIO106: gpio@fd333000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO106"; }; PIO107: gpio@fd334000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO107"; }; diff --git a/arch/arm/boot/dts/stih415.dtsi b/arch/arm/boot/dts/stih415.dtsi index d9c7dd1d95a4..d89064c20c8a 100644 --- a/arch/arm/boot/dts/stih415.dtsi +++ b/arch/arm/boot/dts/stih415.dtsi @@ -10,6 +10,7 @@ #include "stih415-clock.dtsi" #include "stih415-pinctrl.dtsi" #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/reset-controller/stih415-resets.h> / { L2: cache-controller { @@ -28,6 +29,16 @@ ranges; compatible = "simple-bus"; + powerdown: powerdown-controller { + #reset-cells = <1>; + compatible = "st,stih415-powerdown"; + }; + + softreset: softreset-controller { + #reset-cells = <1>; + compatible = "st,stih415-softreset"; + }; + syscfg_sbc: sbc-syscfg@fe600000{ compatible = "st,stih415-sbc-syscfg", "syscon"; reg = <0xfe600000 0xb4>; @@ -136,5 +147,64 @@ status = "disabled"; }; + + ethernet0: dwmac@fe810000 { + device_type = "network"; + compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610"; + status = "disabled"; + + reg = <0xfe810000 0x8000>, <0x148 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; + + interrupts = <0 147 0>, <0 148 0>, <0 149 0>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + resets = <&softreset STIH415_ETH0_SOFTRESET>; + reset-names = "stmmaceth"; + + snps,pbl = <32>; + snps,mixed-burst; + snps,force_sf_dma_mode; + + st,syscon = <&syscfg_rear>; + + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mii0>; + clock-names = "stmmaceth"; + clocks = <&CLKS_GMAC0_PHY>; + }; + + ethernet1: dwmac@fef08000 { + device_type = "network"; + compatible = "st,stih415-dwmac", "snps,dwmac", "snps,dwmac-3.610"; + status = "disabled"; + reg = <0xfef08000 0x8000>, <0x74 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; + interrupts = <0 150 0>, <0 151 0>, <0 152 0>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + + snps,pbl = <32>; + snps,mixed-burst; + snps,force_sf_dma_mode; + + st,syscon = <&syscfg_sbc>; + + resets = <&softreset STIH415_ETH1_SOFTRESET>; + reset-names = "stmmaceth"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mii1>; + clock-names = "stmmaceth"; + clocks = <&CLKS_ETH1_PHY>; + }; + + rc: rc@fe518000 { + compatible = "st,comms-irb"; + reg = <0xfe518000 0x234>; + interrupts = <0 203 0>; + clocks = <&CLK_SYSIN>; + rx-mode = "infrared"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ir>; + resets = <&softreset STIH415_IRB_SOFTRESET>; + }; }; }; diff --git a/arch/arm/boot/dts/stih416-clock.dtsi b/arch/arm/boot/dts/stih416-clock.dtsi index 7026bf1158d8..a6942c75cbbb 100644 --- a/arch/arm/boot/dts/stih416-clock.dtsi +++ b/arch/arm/boot/dts/stih416-clock.dtsi @@ -37,5 +37,19 @@ clock-frequency = <100000000>; clock-output-names = "CLK_S_ICN_REG_0"; }; + + CLK_S_GMAC0_PHY: clockgenA1@7 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + clock-output-names = "CLK_S_GMAC0_PHY"; + }; + + CLK_S_ETH1_PHY: clockgenA0@7 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + clock-output-names = "CLK_S_ETH1_PHY"; + }; }; }; diff --git a/arch/arm/boot/dts/stih416-pinctrl.dtsi b/arch/arm/boot/dts/stih416-pinctrl.dtsi index b29ff4ba542c..aeea304086eb 100644 --- a/arch/arm/boot/dts/stih416-pinctrl.dtsi +++ b/arch/arm/boot/dts/stih416-pinctrl.dtsi @@ -8,6 +8,7 @@ * publishhed by the Free Software Foundation. */ #include "st-pincfg.h" +#include <dt-bindings/interrupt-controller/arm-gic.h> / { aliases { @@ -49,46 +50,69 @@ #size-cells = <1>; compatible = "st,stih416-sbc-pinctrl"; st,syscfg = <&syscfg_sbc>; + reg = <0xfe61f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 182 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfe610000 0x6000>; PIO0: gpio@fe610000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO0"; }; PIO1: gpio@fe611000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO1"; }; PIO2: gpio@fe612000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO2"; }; PIO3: gpio@fe613000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO3"; }; PIO4: gpio@fe614000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO4"; }; PIO40: gpio@fe615000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x5000 0x100>; st,bank-name = "PIO40"; st,retime-pin-mask = <0x7f>; }; + rc{ + pinctrl_ir: ir0 { + st,pins { + ir = <&PIO4 0 ALT2 IN>; + }; + }; + }; sbc_serial1 { pinctrl_sbc_serial1: sbc_serial1 { st,pins { @@ -115,6 +139,58 @@ }; }; }; + + gmac1 { + pinctrl_mii1: mii1 { + st,pins { + txd0 = <&PIO0 0 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txd1 = <&PIO0 1 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txd2 = <&PIO0 2 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txd3 = <&PIO0 3 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txer = <&PIO0 4 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txen = <&PIO0 5 ALT1 OUT SE_NICLK_IO 0 CLK_A>; + txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>; + col = <&PIO0 7 ALT1 IN BYPASS 1000>; + + mdio = <&PIO1 0 ALT1 OUT BYPASS 1500>; + mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>; + crs = <&PIO1 2 ALT1 IN BYPASS 1000>; + mdint = <&PIO1 3 ALT1 IN BYPASS 0>; + rxd0 = <&PIO1 4 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxd1 = <&PIO1 5 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxd2 = <&PIO1 6 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxd3 = <&PIO1 7 ALT1 IN SE_NICLK_IO 0 CLK_A>; + + rxdv = <&PIO2 0 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rx_er = <&PIO2 1 ALT1 IN SE_NICLK_IO 0 CLK_A>; + rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>; + phyclk = <&PIO2 3 ALT1 OUT NICLK 0 CLK_A>; + }; + }; + pinctrl_rgmii1: rgmii1-0 { + st,pins { + txd0 = <&PIO0 0 ALT1 OUT DE_IO 500 CLK_A>; + txd1 = <&PIO0 1 ALT1 OUT DE_IO 500 CLK_A>; + txd2 = <&PIO0 2 ALT1 OUT DE_IO 500 CLK_A>; + txd3 = <&PIO0 3 ALT1 OUT DE_IO 500 CLK_A>; + txen = <&PIO0 5 ALT1 OUT DE_IO 0 CLK_A>; + txclk = <&PIO0 6 ALT1 IN NICLK 0 CLK_A>; + + mdio = <&PIO1 0 ALT1 OUT BYPASS 0>; + mdc = <&PIO1 1 ALT1 OUT NICLK 0 CLK_A>; + rxd0 = <&PIO1 4 ALT1 IN DE_IO 500 CLK_A>; + rxd1 = <&PIO1 5 ALT1 IN DE_IO 500 CLK_A>; + rxd2 = <&PIO1 6 ALT1 IN DE_IO 500 CLK_A>; + rxd3 = <&PIO1 7 ALT1 IN DE_IO 500 CLK_A>; + + rxdv = <&PIO2 0 ALT1 IN DE_IO 500 CLK_A>; + rxclk = <&PIO2 2 ALT1 IN NICLK 0 CLK_A>; + phyclk = <&PIO2 3 ALT4 OUT NICLK 0 CLK_B>; + + clk125= <&PIO3 7 ALT4 IN NICLK 0 CLK_A>; + }; + }; + }; }; pin-controller-front { @@ -122,65 +198,89 @@ #size-cells = <1>; compatible = "st,stih416-front-pinctrl"; st,syscfg = <&syscfg_front>; + reg = <0xfee0f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfee00000 0x10000>; PIO5: gpio@fee00000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO5"; }; PIO6: gpio@fee01000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO6"; }; PIO7: gpio@fee02000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO7"; }; PIO8: gpio@fee03000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO8"; }; PIO9: gpio@fee04000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO9"; }; PIO10: gpio@fee05000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x5000 0x100>; st,bank-name = "PIO10"; }; PIO11: gpio@fee06000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x6000 0x100>; st,bank-name = "PIO11"; }; PIO12: gpio@fee07000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x7000 0x100>; st,bank-name = "PIO12"; }; PIO30: gpio@fee08000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x8000 0x100>; st,bank-name = "PIO30"; }; PIO31: gpio@fee09000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x9000 0x100>; st,bank-name = "PIO31"; }; @@ -210,6 +310,19 @@ }; }; }; + + fsm { + pinctrl_fsm: fsm { + st,pins { + spi-fsm-clk = <&PIO12 2 ALT1 OUT>; + spi-fsm-cs = <&PIO12 3 ALT1 OUT>; + spi-fsm-mosi = <&PIO12 4 ALT1 OUT>; + spi-fsm-miso = <&PIO12 5 ALT1 IN>; + spi-fsm-hol = <&PIO12 6 ALT1 OUT>; + spi-fsm-wp = <&PIO12 7 ALT1 OUT>; + }; + }; + }; }; pin-controller-rear { @@ -217,41 +330,57 @@ #size-cells = <1>; compatible = "st,stih416-rear-pinctrl"; st,syscfg = <&syscfg_rear>; + reg = <0xfe82f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 184 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfe820000 0x6000>; PIO13: gpio@fe820000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO13"; }; PIO14: gpio@fe821000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO14"; }; PIO15: gpio@fe822000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO15"; }; PIO16: gpio@fe823000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO16"; }; PIO17: gpio@fe824000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO17"; }; PIO18: gpio@fe825000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x5000 0x100>; st,bank-name = "PIO18"; st,retime-pin-mask = <0xf>; @@ -265,6 +394,63 @@ }; }; }; + + gmac0 { + pinctrl_mii0: mii0 { + st,pins { + mdint = <&PIO13 6 ALT2 IN BYPASS 0>; + txen = <&PIO13 7 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + txd0 = <&PIO14 0 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + txd1 = <&PIO14 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + txd2 = <&PIO14 2 ALT2 OUT SE_NICLK_IO 0 CLK_B>; + txd3 = <&PIO14 3 ALT2 OUT SE_NICLK_IO 0 CLK_B>; + + txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>; + txer = <&PIO15 1 ALT2 OUT SE_NICLK_IO 0 CLK_A>; + crs = <&PIO15 2 ALT2 IN BYPASS 1000>; + col = <&PIO15 3 ALT2 IN BYPASS 1000>; + mdio= <&PIO15 4 ALT2 OUT BYPASS 1500>; + mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>; + + rxd0 = <&PIO16 0 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxd1 = <&PIO16 1 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxd2 = <&PIO16 2 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxd3 = <&PIO16 3 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxdv = <&PIO15 6 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rx_er = <&PIO15 7 ALT2 IN SE_NICLK_IO 0 CLK_A>; + rxclk = <&PIO17 0 ALT2 IN NICLK 0 CLK_A>; + phyclk = <&PIO13 5 ALT2 OUT NICLK 0 CLK_B>; + }; + }; + + pinctrl_gmii0: gmii0 { + st,pins { + }; + }; + pinctrl_rgmii0: rgmii0 { + st,pins { + phyclk = <&PIO13 5 ALT4 OUT NICLK 0 CLK_B>; + txen = <&PIO13 7 ALT2 OUT DE_IO 0 CLK_A>; + txd0 = <&PIO14 0 ALT2 OUT DE_IO 500 CLK_A>; + txd1 = <&PIO14 1 ALT2 OUT DE_IO 500 CLK_A>; + txd2 = <&PIO14 2 ALT2 OUT DE_IO 500 CLK_B>; + txd3 = <&PIO14 3 ALT2 OUT DE_IO 500 CLK_B>; + txclk = <&PIO15 0 ALT2 IN NICLK 0 CLK_A>; + + mdio = <&PIO15 4 ALT2 OUT BYPASS 0>; + mdc = <&PIO15 5 ALT2 OUT NICLK 0 CLK_B>; + + rxdv = <&PIO15 6 ALT2 IN DE_IO 500 CLK_A>; + rxd0 =<&PIO16 0 ALT2 IN DE_IO 500 CLK_A>; + rxd1 =<&PIO16 1 ALT2 IN DE_IO 500 CLK_A>; + rxd2 =<&PIO16 2 ALT2 IN DE_IO 500 CLK_A>; + rxd3 =<&PIO16 3 ALT2 IN DE_IO 500 CLK_A>; + rxclk =<&PIO17 0 ALT2 IN NICLK 0 CLK_A>; + + clk125=<&PIO17 6 ALT1 IN NICLK 0 CLK_A>; + }; + }; + }; }; pin-controller-fvdp-fe { @@ -272,23 +458,33 @@ #size-cells = <1>; compatible = "st,stih416-fvdp-fe-pinctrl"; st,syscfg = <&syscfg_fvdp_fe>; + reg = <0xfd6bf080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfd6b0000 0x3000>; PIO100: gpio@fd6b0000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO100"; }; PIO101: gpio@fd6b1000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO101"; }; PIO102: gpio@fd6b2000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO102"; }; @@ -299,29 +495,41 @@ #size-cells = <1>; compatible = "st,stih416-fvdp-lite-pinctrl"; st,syscfg = <&syscfg_fvdp_lite>; + reg = <0xfd33f080 0x4>; + reg-names = "irqmux"; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; + interrupts-names = "irqmux"; ranges = <0 0xfd330000 0x5000>; PIO103: gpio@fd330000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0 0x100>; st,bank-name = "PIO103"; }; PIO104: gpio@fd331000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x1000 0x100>; st,bank-name = "PIO104"; }; PIO105: gpio@fd332000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x2000 0x100>; st,bank-name = "PIO105"; }; PIO106: gpio@fd333000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x3000 0x100>; st,bank-name = "PIO106"; }; @@ -329,6 +537,8 @@ PIO107: gpio@fd334000 { gpio-controller; #gpio-cells = <1>; + interrupt-controller; + #interrupt-cells = <2>; reg = <0x4000 0x100>; st,bank-name = "PIO107"; st,retime-pin-mask = <0xf>; diff --git a/arch/arm/boot/dts/stih416.dtsi b/arch/arm/boot/dts/stih416.dtsi index b7ab47b95816..78746d20382e 100644 --- a/arch/arm/boot/dts/stih416.dtsi +++ b/arch/arm/boot/dts/stih416.dtsi @@ -10,6 +10,7 @@ #include "stih416-clock.dtsi" #include "stih416-pinctrl.dtsi" #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/reset-controller/stih416-resets.h> / { L2: cache-controller { compatible = "arm,pl310-cache"; @@ -27,6 +28,16 @@ ranges; compatible = "simple-bus"; + powerdown: powerdown-controller { + #reset-cells = <1>; + compatible = "st,stih416-powerdown"; + }; + + softreset: softreset-controller { + #reset-cells = <1>; + compatible = "st,stih416-softreset"; + }; + syscfg_sbc:sbc-syscfg@fe600000{ compatible = "st,stih416-sbc-syscfg", "syscon"; reg = <0xfe600000 0x1000>; @@ -145,5 +156,73 @@ status = "disabled"; }; + + ethernet0: dwmac@fe810000 { + device_type = "network"; + compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710"; + status = "disabled"; + reg = <0xfe810000 0x8000>, <0x8bc 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; + + interrupts = <0 133 0>, <0 134 0>, <0 135 0>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + + snps,pbl = <32>; + snps,mixed-burst; + + st,syscon = <&syscfg_rear>; + resets = <&softreset STIH416_ETH0_SOFTRESET>; + reset-names = "stmmaceth"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mii0>; + clock-names = "stmmaceth"; + clocks = <&CLK_S_GMAC0_PHY>; + }; + + ethernet1: dwmac@fef08000 { + device_type = "network"; + compatible = "st,stih416-dwmac", "snps,dwmac", "snps,dwmac-3.710"; + status = "disabled"; + reg = <0xfef08000 0x8000>, <0x7f0 0x4>; + reg-names = "stmmaceth", "sti-ethconf"; + interrupts = <0 136 0>, <0 137 0>, <0 138 0>; + interrupt-names = "macirq", "eth_wake_irq", "eth_lpi"; + + snps,pbl = <32>; + snps,mixed-burst; + + st,syscon = <&syscfg_sbc>; + + resets = <&softreset STIH416_ETH1_SOFTRESET>; + reset-names = "stmmaceth"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_mii1>; + clock-names = "stmmaceth"; + clocks = <&CLK_S_ETH1_PHY>; + }; + + rc: rc@fe518000 { + compatible = "st,comms-irb"; + reg = <0xfe518000 0x234>; + interrupts = <0 203 0>; + rx-mode = "infrared"; + clocks = <&CLK_SYSIN>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ir>; + resets = <&softreset STIH416_IRB_SOFTRESET>; + }; + + /* FSM */ + spifsm: spifsm@fe902000 { + compatible = "st,spi-fsm"; + reg = <0xfe902000 0x1000>; + pinctrl-0 = <&pinctrl_fsm>; + + st,syscfg = <&syscfg_rear>; + st,boot-device-reg = <0x958>; + st,boot-device-spi = <0x1a>; + + status = "disabled"; + }; }; }; diff --git a/arch/arm/boot/dts/stih41x-b2000.dtsi b/arch/arm/boot/dts/stih41x-b2000.dtsi index 1e6aa92772f5..bf65c49095af 100644 --- a/arch/arm/boot/dts/stih41x-b2000.dtsi +++ b/arch/arm/boot/dts/stih41x-b2000.dtsi @@ -20,6 +20,8 @@ aliases { ttyAS0 = &serial2; + ethernet0 = ðernet0; + ethernet1 = ðernet1; }; soc { @@ -46,5 +48,25 @@ status = "okay"; }; + + ethernet0: dwmac@fe810000 { + status = "okay"; + phy-mode = "mii"; + pinctrl-0 = <&pinctrl_mii0>; + + snps,reset-gpio = <&PIO106 2>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 10000>; + }; + + ethernet1: dwmac@fef08000 { + status = "disabled"; + phy-mode = "mii"; + st,tx-retime-src = "txclk"; + + snps,reset-gpio = <&PIO4 7>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 10000>; + }; }; }; diff --git a/arch/arm/boot/dts/stih41x-b2020.dtsi b/arch/arm/boot/dts/stih41x-b2020.dtsi index 0ef0a69df8ea..838513f9ddc0 100644 --- a/arch/arm/boot/dts/stih41x-b2020.dtsi +++ b/arch/arm/boot/dts/stih41x-b2020.dtsi @@ -6,6 +6,7 @@ * it under the terms of the GNU General Public License version 2 as * publishhed by the Free Software Foundation. */ +#include "stih41x-b2020x.dtsi" / { memory{ device_type = "memory"; @@ -19,6 +20,7 @@ aliases { ttyAS0 = &sbc_serial1; + ethernet1 = ðernet1; }; soc { sbc_serial1: serial@fe531000 { @@ -60,5 +62,17 @@ i2c@fe541000 { status = "okay"; }; + + ethernet1: dwmac@fef08000 { + status = "okay"; + phy-mode = "rgmii-id"; + max-speed = <1000>; + st,tx-retime-src = "clk_125"; + snps,reset-gpio = <&PIO3 0>; + snps,reset-active-low; + snps,reset-delays-us = <0 10000 10000>; + + pinctrl-0 = <&pinctrl_rgmii1>; + }; }; }; diff --git a/arch/arm/boot/dts/stih41x-b2020x.dtsi b/arch/arm/boot/dts/stih41x-b2020x.dtsi new file mode 100644 index 000000000000..df01c1211b32 --- /dev/null +++ b/arch/arm/boot/dts/stih41x-b2020x.dtsi @@ -0,0 +1,28 @@ +/* + * Copyright (C) 2013 STMicroelectronics (R&D) Limited. + * Author: Lee Jones <lee.jones@linaro.org> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * publishhed by the Free Software Foundation. + */ +/ { + soc { + spifsm: spifsm@fe902000 { + #address-cells = <1>; + #size-cells = <1>; + + status = "okay"; + + partition@0 { + label = "SerialFlash1"; + reg = <0x00000000 0x00500000>; + }; + + partition@500000 { + label = "SerialFlash2"; + reg = <0x00500000 0x00b00000>; + }; + }; + }; +}; diff --git a/arch/arm/boot/dts/sun4i-a10-a1000.dts b/arch/arm/boot/dts/sun4i-a10-a1000.dts index d4b081d6a167..fa746aea5e66 100644 --- a/arch/arm/boot/dts/sun4i-a10-a1000.dts +++ b/arch/arm/boot/dts/sun4i-a10-a1000.dts @@ -13,6 +13,7 @@ /dts-v1/; /include/ "sun4i-a10.dtsi" +/include/ "sunxi-common-regulators.dtsi" / { model = "Mele A1000"; @@ -35,6 +36,32 @@ }; }; + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + ahci: sata@01c18000 { + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; + }; + pinctrl@01c20800 { emac_power_pin_a1000: emac_power_pin@0 { allwinner,pins = "PH15"; @@ -80,18 +107,22 @@ }; }; - regulators { - compatible = "simple-bus"; + reg_emac_3v3: emac-3v3 { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&emac_power_pin_a1000>; + regulator-name = "emac-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + gpio = <&pio 7 15 0>; + }; - reg_emac_3v3: emac-3v3 { - compatible = "regulator-fixed"; - pinctrl-names = "default"; - pinctrl-0 = <&emac_power_pin_a1000>; - regulator-name = "emac-3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - enable-active-high; - gpio = <&pio 7 15 0>; - }; + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; }; }; diff --git a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts index b139ee6bcf99..4684cbe6843b 100644 --- a/arch/arm/boot/dts/sun4i-a10-cubieboard.dts +++ b/arch/arm/boot/dts/sun4i-a10-cubieboard.dts @@ -12,6 +12,7 @@ /dts-v1/; /include/ "sun4i-a10.dtsi" +/include/ "sunxi-common-regulators.dtsi" / { model = "Cubietech Cubieboard"; @@ -33,6 +34,33 @@ }; }; + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + ahci: sata@01c18000 { + target-supply = <®_ahci_5v>; + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; + }; + pinctrl@01c20800 { led_pins_cubieboard: led_pins@0 { allwinner,pins = "PH20", "PH21"; @@ -77,4 +105,16 @@ linux,default-trigger = "heartbeat"; }; }; + + reg_ahci_5v: ahci-5v { + status = "okay"; + }; + + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; + }; }; diff --git a/arch/arm/boot/dts/sun4i-a10-hackberry.dts b/arch/arm/boot/dts/sun4i-a10-hackberry.dts index 3a1595f67823..d7c17e46ce23 100644 --- a/arch/arm/boot/dts/sun4i-a10-hackberry.dts +++ b/arch/arm/boot/dts/sun4i-a10-hackberry.dts @@ -13,6 +13,7 @@ /dts-v1/; /include/ "sun4i-a10.dtsi" +/include/ "sunxi-common-regulators.dtsi" / { model = "Miniand Hackberry"; @@ -35,6 +36,28 @@ }; }; + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; + }; + pio: pinctrl@01c20800 { pinctrl-names = "default"; pinctrl-0 = <&hackberry_hogs>; @@ -45,6 +68,13 @@ allwinner,drive = <0>; allwinner,pull = <0>; }; + + usb2_vbus_pin_hackberry: usb2_vbus_pin@0 { + allwinner,pins = "PH12"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; }; uart0: serial@01c28000 { @@ -54,16 +84,22 @@ }; }; - regulators { - compatible = "simple-bus"; + reg_emac_3v3: emac-3v3 { + compatible = "regulator-fixed"; + regulator-name = "emac-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + enable-active-high; + gpio = <&pio 7 19 0>; + }; - reg_emac_3v3: emac-3v3 { - compatible = "regulator-fixed"; - regulator-name = "emac-3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; - enable-active-high; - gpio = <&pio 7 19 0>; - }; + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + pinctrl-0 = <&usb2_vbus_pin_hackberry>; + gpio = <&pio 7 12 0>; + status = "okay"; }; }; diff --git a/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts b/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts new file mode 100644 index 000000000000..fe9272ee55c3 --- /dev/null +++ b/arch/arm/boot/dts/sun4i-a10-inet97fv2.dts @@ -0,0 +1,69 @@ +/* + * Copyright 2014 Open Source Support GmbH + * + * David Lanzendörfer <david.lanzendoerfer@o2s.ch> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "sun4i-a10.dtsi" +/include/ "sunxi-common-regulators.dtsi" + +/ { + model = "INet-97F Rev 02"; + compatible = "primux,inet97fv2", "allwinner,sun4i-a10"; + + aliases { + serial0 = &uart0; + }; + + soc@01c00000 { + uart0: serial@01c28000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; + }; + + i2c0: i2c@01c2ac00 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + }; + + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; + }; + }; + + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/sun4i-a10-mini-xplus.dts b/arch/arm/boot/dts/sun4i-a10-mini-xplus.dts index 70b3323caf1a..dd84a9e313b3 100644 --- a/arch/arm/boot/dts/sun4i-a10-mini-xplus.dts +++ b/arch/arm/boot/dts/sun4i-a10-mini-xplus.dts @@ -13,16 +13,47 @@ /dts-v1/; /include/ "sun4i-a10.dtsi" +/include/ "sunxi-common-regulators.dtsi" / { model = "PineRiver Mini X-Plus"; compatible = "pineriver,mini-xplus", "allwinner,sun4i-a10"; soc@01c00000 { + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; + }; + uart0: serial@01c28000 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; status = "okay"; }; }; + + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; + }; }; diff --git a/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts b/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts new file mode 100644 index 000000000000..66cf0c7cf5b7 --- /dev/null +++ b/arch/arm/boot/dts/sun4i-a10-olinuxino-lime.dts @@ -0,0 +1,111 @@ +/* + * Copyright 2014 - Hans de Goede <hdegoede@redhat.com> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "sun4i-a10.dtsi" +/include/ "sunxi-common-regulators.dtsi" + +/ { + model = "Olimex A10-OLinuXino-LIME"; + compatible = "olimex,a10-olinuxino-lime", "allwinner,sun4i-a10"; + + soc@01c00000 { + emac: ethernet@01c0b000 { + pinctrl-names = "default"; + pinctrl-0 = <&emac_pins_a>; + phy = <&phy1>; + status = "okay"; + }; + + mdio@01c0b080 { + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + ahci: sata@01c18000 { + target-supply = <®_ahci_5v>; + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; + }; + + pinctrl@01c20800 { + ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 { + allwinner,pins = "PC3"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + led_pins_olinuxinolime: led_pins@0 { + allwinner,pins = "PH2"; + allwinner,function = "gpio_out"; + allwinner,drive = <1>; + allwinner,pull = <0>; + }; + }; + + uart0: serial@01c28000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; + }; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pins_olinuxinolime>; + + green { + label = "a10-olinuxino-lime:green:usr"; + gpios = <&pio 7 2 0>; + default-state = "on"; + }; + }; + + reg_ahci_5v: ahci-5v { + pinctrl-0 = <&ahci_pwr_pin_olinuxinolime>; + gpio = <&pio 2 3 0>; + status = "okay"; + }; + + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/sun4i-a10-pcduino.dts b/arch/arm/boot/dts/sun4i-a10-pcduino.dts new file mode 100644 index 000000000000..255b47e7019c --- /dev/null +++ b/arch/arm/boot/dts/sun4i-a10-pcduino.dts @@ -0,0 +1,79 @@ +/* + * Copyright 2014 Zoltan HERPAI + * Zoltan HERPAI <wigyori@uid0.hu> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/dts-v1/; +/include/ "sun4i-a10.dtsi" +/include/ "sunxi-common-regulators.dtsi" + +/ { + model = "LinkSprite pcDuino"; + compatible = "linksprite,a10-pcduino", "allwinner,sun4i-a10"; + + soc@01c00000 { + emac: ethernet@01c0b000 { + pinctrl-names = "default"; + pinctrl-0 = <&emac_pins_a>; + phy = <&phy1>; + status = "okay"; + }; + + mdio@01c0b080 { + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; + + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; + }; + + uart0: serial@01c28000 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_a>; + status = "okay"; + }; + + i2c0: i2c@01c2ac00 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "okay"; + }; + }; + + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; + }; +}; diff --git a/arch/arm/boot/dts/sun4i-a10.dtsi b/arch/arm/boot/dts/sun4i-a10.dtsi index 9321681cc45a..9174724571e2 100644 --- a/arch/arm/boot/dts/sun4i-a10.dtsi +++ b/arch/arm/boot/dts/sun4i-a10.dtsi @@ -19,6 +19,12 @@ ethernet0 = &emac; serial0 = &uart0; serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + serial6 = &uart6; + serial7 = &uart7; }; cpus { @@ -52,44 +58,48 @@ clock-frequency = <0>; }; - osc24M: osc24M@01c20050 { + osc24M: clk@01c20050 { #clock-cells = <0>; - compatible = "allwinner,sun4i-osc-clk"; + compatible = "allwinner,sun4i-a10-osc-clk"; reg = <0x01c20050 0x4>; clock-frequency = <24000000>; + clock-output-names = "osc24M"; }; - osc32k: osc32k { + osc32k: clk@0 { #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <32768>; + clock-output-names = "osc32k"; }; - pll1: pll1@01c20000 { + pll1: clk@01c20000 { #clock-cells = <0>; - compatible = "allwinner,sun4i-pll1-clk"; + compatible = "allwinner,sun4i-a10-pll1-clk"; reg = <0x01c20000 0x4>; clocks = <&osc24M>; + clock-output-names = "pll1"; }; - pll4: pll4@01c20018 { + pll4: clk@01c20018 { #clock-cells = <0>; - compatible = "allwinner,sun4i-pll1-clk"; + compatible = "allwinner,sun4i-a10-pll1-clk"; reg = <0x01c20018 0x4>; clocks = <&osc24M>; + clock-output-names = "pll4"; }; - pll5: pll5@01c20020 { + pll5: clk@01c20020 { #clock-cells = <1>; - compatible = "allwinner,sun4i-pll5-clk"; + compatible = "allwinner,sun4i-a10-pll5-clk"; reg = <0x01c20020 0x4>; clocks = <&osc24M>; clock-output-names = "pll5_ddr", "pll5_other"; }; - pll6: pll6@01c20028 { + pll6: clk@01c20028 { #clock-cells = <1>; - compatible = "allwinner,sun4i-pll6-clk"; + compatible = "allwinner,sun4i-a10-pll6-clk"; reg = <0x01c20028 0x4>; clocks = <&osc24M>; clock-output-names = "pll6_sata", "pll6_other", "pll6"; @@ -98,21 +108,23 @@ /* dummy is 200M */ cpu: cpu@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-cpu-clk"; + compatible = "allwinner,sun4i-a10-cpu-clk"; reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>; + clock-output-names = "cpu"; }; axi: axi@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-axi-clk"; + compatible = "allwinner,sun4i-a10-axi-clk"; reg = <0x01c20054 0x4>; clocks = <&cpu>; + clock-output-names = "axi"; }; - axi_gates: axi_gates@01c2005c { + axi_gates: clk@01c2005c { #clock-cells = <1>; - compatible = "allwinner,sun4i-axi-gates-clk"; + compatible = "allwinner,sun4i-a10-axi-gates-clk"; reg = <0x01c2005c 0x4>; clocks = <&axi>; clock-output-names = "axi_dram"; @@ -120,14 +132,15 @@ ahb: ahb@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-ahb-clk"; + compatible = "allwinner,sun4i-a10-ahb-clk"; reg = <0x01c20054 0x4>; clocks = <&axi>; + clock-output-names = "ahb"; }; - ahb_gates: ahb_gates@01c20060 { + ahb_gates: clk@01c20060 { #clock-cells = <1>; - compatible = "allwinner,sun4i-ahb-gates-clk"; + compatible = "allwinner,sun4i-a10-ahb-gates-clk"; reg = <0x01c20060 0x8>; clocks = <&ahb>; clock-output-names = "ahb_usb0", "ahb_ehci0", @@ -145,14 +158,15 @@ apb0: apb0@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb0-clk"; + compatible = "allwinner,sun4i-a10-apb0-clk"; reg = <0x01c20054 0x4>; clocks = <&ahb>; + clock-output-names = "apb0"; }; - apb0_gates: apb0_gates@01c20068 { + apb0_gates: clk@01c20068 { #clock-cells = <1>; - compatible = "allwinner,sun4i-apb0-gates-clk"; + compatible = "allwinner,sun4i-a10-apb0-gates-clk"; reg = <0x01c20068 0x4>; clocks = <&apb0>; clock-output-names = "apb0_codec", "apb0_spdif", @@ -162,21 +176,23 @@ apb1_mux: apb1_mux@01c20058 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb1-mux-clk"; + compatible = "allwinner,sun4i-a10-apb1-mux-clk"; reg = <0x01c20058 0x4>; clocks = <&osc24M>, <&pll6 1>, <&osc32k>; + clock-output-names = "apb1_mux"; }; apb1: apb1@01c20058 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb1-clk"; + compatible = "allwinner,sun4i-a10-apb1-clk"; reg = <0x01c20058 0x4>; clocks = <&apb1_mux>; + clock-output-names = "apb1"; }; - apb1_gates: apb1_gates@01c2006c { + apb1_gates: clk@01c2006c { #clock-cells = <1>; - compatible = "allwinner,sun4i-apb1-gates-clk"; + compatible = "allwinner,sun4i-a10-apb1-gates-clk"; reg = <0x01c2006c 0x4>; clocks = <&apb1>; clock-output-names = "apb1_i2c0", "apb1_i2c1", @@ -189,7 +205,7 @@ nand_clk: clk@01c20080 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20080 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "nand"; @@ -197,7 +213,7 @@ ms_clk: clk@01c20084 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20084 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ms"; @@ -205,7 +221,7 @@ mmc0_clk: clk@01c20088 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20088 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc0"; @@ -213,7 +229,7 @@ mmc1_clk: clk@01c2008c { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c2008c 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc1"; @@ -221,7 +237,7 @@ mmc2_clk: clk@01c20090 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20090 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc2"; @@ -229,7 +245,7 @@ mmc3_clk: clk@01c20094 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20094 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc3"; @@ -237,7 +253,7 @@ ts_clk: clk@01c20098 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20098 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ts"; @@ -245,7 +261,7 @@ ss_clk: clk@01c2009c { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c2009c 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ss"; @@ -253,7 +269,7 @@ spi0_clk: clk@01c200a0 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200a0 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi0"; @@ -261,7 +277,7 @@ spi1_clk: clk@01c200a4 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200a4 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi1"; @@ -269,7 +285,7 @@ spi2_clk: clk@01c200a8 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200a8 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi2"; @@ -277,7 +293,7 @@ pata_clk: clk@01c200ac { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200ac 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "pata"; @@ -285,7 +301,7 @@ ir0_clk: clk@01c200b0 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200b0 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ir0"; @@ -293,15 +309,24 @@ ir1_clk: clk@01c200b4 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200b4 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ir1"; }; + usb_clk: clk@01c200cc { + #clock-cells = <1>; + #reset-cells = <1>; + compatible = "allwinner,sun4i-a10-usb-clk"; + reg = <0x01c200cc 0x4>; + clocks = <&pll6 1>; + clock-output-names = "usb_ohci0", "usb_ohci1", "usb_phy"; + }; + spi3_clk: clk@01c200d4 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200d4 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi3"; @@ -314,6 +339,28 @@ #size-cells = <1>; ranges; + spi0: spi@01c05000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c05000 0x1000>; + interrupts = <10>; + clocks = <&ahb_gates 20>, <&spi0_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + spi1: spi@01c06000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c06000 0x1000>; + interrupts = <11>; + clocks = <&ahb_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + emac: ethernet@01c0b000 { compatible = "allwinner,sun4i-a10-emac"; reg = <0x01c0b000 0x1000>; @@ -330,6 +377,88 @@ #size-cells = <0>; }; + usbphy: phy@01c13400 { + #phy-cells = <1>; + compatible = "allwinner,sun4i-a10-usb-phy"; + reg = <0x01c13400 0x10 0x01c14800 0x4 0x01c1c800 0x4>; + reg-names = "phy_ctrl", "pmu1", "pmu2"; + clocks = <&usb_clk 8>; + clock-names = "usb_phy"; + resets = <&usb_clk 1>, <&usb_clk 2>; + reset-names = "usb1_reset", "usb2_reset"; + status = "disabled"; + }; + + ehci0: usb@01c14000 { + compatible = "allwinner,sun4i-a10-ehci", "generic-ehci"; + reg = <0x01c14000 0x100>; + interrupts = <39>; + clocks = <&ahb_gates 1>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + ohci0: usb@01c14400 { + compatible = "allwinner,sun4i-a10-ohci", "generic-ohci"; + reg = <0x01c14400 0x100>; + interrupts = <64>; + clocks = <&usb_clk 6>, <&ahb_gates 2>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + spi2: spi@01c17000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c17000 0x1000>; + interrupts = <12>; + clocks = <&ahb_gates 22>, <&spi2_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + ahci: sata@01c18000 { + compatible = "allwinner,sun4i-a10-ahci"; + reg = <0x01c18000 0x1000>; + interrupts = <56>; + clocks = <&pll6 0>, <&ahb_gates 25>; + status = "disabled"; + }; + + ehci1: usb@01c1c000 { + compatible = "allwinner,sun4i-a10-ehci", "generic-ehci"; + reg = <0x01c1c000 0x100>; + interrupts = <40>; + clocks = <&ahb_gates 3>; + phys = <&usbphy 2>; + phy-names = "usb"; + status = "disabled"; + }; + + ohci1: usb@01c1c400 { + compatible = "allwinner,sun4i-a10-ohci", "generic-ohci"; + reg = <0x01c1c400 0x100>; + interrupts = <65>; + clocks = <&usb_clk 7>, <&ahb_gates 4>; + phys = <&usbphy 2>; + phy-names = "usb"; + status = "disabled"; + }; + + spi3: spi@01c1f000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c1f000 0x1000>; + interrupts = <50>; + clocks = <&ahb_gates 23>, <&spi3_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + intc: interrupt-controller@01c20400 { compatible = "allwinner,sun4i-a10-ic"; reg = <0x01c20400 0x400>; @@ -410,7 +539,7 @@ }; wdt: watchdog@01c20c90 { - compatible = "allwinner,sun4i-wdt"; + compatible = "allwinner,sun4i-a10-wdt"; reg = <0x01c20c90 0x10>; }; diff --git a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts index 3c9f8b3cd3e3..23611b71d3aa 100644 --- a/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts +++ b/arch/arm/boot/dts/sun5i-a10s-olinuxino-micro.dts @@ -13,6 +13,7 @@ /dts-v1/; /include/ "sun5i-a10s.dtsi" +/include/ "sunxi-common-regulators.dtsi" / { model = "Olimex A10s-Olinuxino Micro"; @@ -34,6 +35,19 @@ }; }; + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + pinctrl@01c20800 { led_pins_olinuxino: led_pins@0 { allwinner,pins = "PE3"; @@ -41,6 +55,13 @@ allwinner,drive = <1>; allwinner,pull = <0>; }; + + usb1_vbus_pin_olinuxino_m: usb1_vbus_pin@0 { + allwinner,pins = "PB10"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; }; uart0: serial@01c28000 { @@ -98,4 +119,10 @@ default-state = "on"; }; }; + + reg_usb1_vbus: usb1-vbus { + pinctrl-0 = <&usb1_vbus_pin_olinuxino_m>; + gpio = <&pio 1 10 0>; + status = "okay"; + }; }; diff --git a/arch/arm/boot/dts/sun5i-a10s.dtsi b/arch/arm/boot/dts/sun5i-a10s.dtsi index ee17b1c379e3..79989ed5658d 100644 --- a/arch/arm/boot/dts/sun5i-a10s.dtsi +++ b/arch/arm/boot/dts/sun5i-a10s.dtsi @@ -18,6 +18,10 @@ aliases { ethernet0 = &emac; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; }; cpus { @@ -47,44 +51,48 @@ clock-frequency = <0>; }; - osc24M: osc24M@01c20050 { + osc24M: clk@01c20050 { #clock-cells = <0>; - compatible = "allwinner,sun4i-osc-clk"; + compatible = "allwinner,sun4i-a10-osc-clk"; reg = <0x01c20050 0x4>; clock-frequency = <24000000>; + clock-output-names = "osc24M"; }; - osc32k: osc32k { + osc32k: clk@0 { #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <32768>; + clock-output-names = "osc32k"; }; - pll1: pll1@01c20000 { + pll1: clk@01c20000 { #clock-cells = <0>; - compatible = "allwinner,sun4i-pll1-clk"; + compatible = "allwinner,sun4i-a10-pll1-clk"; reg = <0x01c20000 0x4>; clocks = <&osc24M>; + clock-output-names = "pll1"; }; - pll4: pll4@01c20018 { + pll4: clk@01c20018 { #clock-cells = <0>; - compatible = "allwinner,sun4i-pll1-clk"; + compatible = "allwinner,sun4i-a10-pll1-clk"; reg = <0x01c20018 0x4>; clocks = <&osc24M>; + clock-output-names = "pll4"; }; - pll5: pll5@01c20020 { + pll5: clk@01c20020 { #clock-cells = <1>; - compatible = "allwinner,sun4i-pll5-clk"; + compatible = "allwinner,sun4i-a10-pll5-clk"; reg = <0x01c20020 0x4>; clocks = <&osc24M>; clock-output-names = "pll5_ddr", "pll5_other"; }; - pll6: pll6@01c20028 { + pll6: clk@01c20028 { #clock-cells = <1>; - compatible = "allwinner,sun4i-pll6-clk"; + compatible = "allwinner,sun4i-a10-pll6-clk"; reg = <0x01c20028 0x4>; clocks = <&osc24M>; clock-output-names = "pll6_sata", "pll6_other", "pll6"; @@ -93,21 +101,23 @@ /* dummy is 200M */ cpu: cpu@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-cpu-clk"; + compatible = "allwinner,sun4i-a10-cpu-clk"; reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>; + clock-output-names = "cpu"; }; axi: axi@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-axi-clk"; + compatible = "allwinner,sun4i-a10-axi-clk"; reg = <0x01c20054 0x4>; clocks = <&cpu>; + clock-output-names = "axi"; }; - axi_gates: axi_gates@01c2005c { + axi_gates: clk@01c2005c { #clock-cells = <1>; - compatible = "allwinner,sun4i-axi-gates-clk"; + compatible = "allwinner,sun4i-a10-axi-gates-clk"; reg = <0x01c2005c 0x4>; clocks = <&axi>; clock-output-names = "axi_dram"; @@ -115,12 +125,13 @@ ahb: ahb@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-ahb-clk"; + compatible = "allwinner,sun4i-a10-ahb-clk"; reg = <0x01c20054 0x4>; clocks = <&axi>; + clock-output-names = "ahb"; }; - ahb_gates: ahb_gates@01c20060 { + ahb_gates: clk@01c20060 { #clock-cells = <1>; compatible = "allwinner,sun5i-a10s-ahb-gates-clk"; reg = <0x01c20060 0x8>; @@ -136,12 +147,13 @@ apb0: apb0@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb0-clk"; + compatible = "allwinner,sun4i-a10-apb0-clk"; reg = <0x01c20054 0x4>; clocks = <&ahb>; + clock-output-names = "apb0"; }; - apb0_gates: apb0_gates@01c20068 { + apb0_gates: clk@01c20068 { #clock-cells = <1>; compatible = "allwinner,sun5i-a10s-apb0-gates-clk"; reg = <0x01c20068 0x4>; @@ -152,19 +164,21 @@ apb1_mux: apb1_mux@01c20058 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb1-mux-clk"; + compatible = "allwinner,sun4i-a10-apb1-mux-clk"; reg = <0x01c20058 0x4>; clocks = <&osc24M>, <&pll6 1>, <&osc32k>; + clock-output-names = "apb1_mux"; }; apb1: apb1@01c20058 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb1-clk"; + compatible = "allwinner,sun4i-a10-apb1-clk"; reg = <0x01c20058 0x4>; clocks = <&apb1_mux>; + clock-output-names = "apb1"; }; - apb1_gates: apb1_gates@01c2006c { + apb1_gates: clk@01c2006c { #clock-cells = <1>; compatible = "allwinner,sun5i-a10s-apb1-gates-clk"; reg = <0x01c2006c 0x4>; @@ -176,7 +190,7 @@ nand_clk: clk@01c20080 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20080 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "nand"; @@ -184,7 +198,7 @@ ms_clk: clk@01c20084 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20084 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ms"; @@ -192,7 +206,7 @@ mmc0_clk: clk@01c20088 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20088 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc0"; @@ -200,7 +214,7 @@ mmc1_clk: clk@01c2008c { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c2008c 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc1"; @@ -208,7 +222,7 @@ mmc2_clk: clk@01c20090 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20090 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc2"; @@ -216,7 +230,7 @@ ts_clk: clk@01c20098 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20098 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ts"; @@ -224,7 +238,7 @@ ss_clk: clk@01c2009c { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c2009c 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ss"; @@ -232,7 +246,7 @@ spi0_clk: clk@01c200a0 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200a0 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi0"; @@ -240,7 +254,7 @@ spi1_clk: clk@01c200a4 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200a4 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi1"; @@ -248,7 +262,7 @@ spi2_clk: clk@01c200a8 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200a8 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi2"; @@ -256,15 +270,24 @@ ir0_clk: clk@01c200b0 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200b0 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ir0"; }; + usb_clk: clk@01c200cc { + #clock-cells = <1>; + #reset-cells = <1>; + compatible = "allwinner,sun5i-a13-usb-clk"; + reg = <0x01c200cc 0x4>; + clocks = <&pll6 1>; + clock-output-names = "usb_ohci0", "usb_phy"; + }; + mbus_clk: clk@01c2015c { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c2015c 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mbus"; @@ -277,6 +300,28 @@ #size-cells = <1>; ranges; + spi0: spi@01c05000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c05000 0x1000>; + interrupts = <10>; + clocks = <&ahb_gates 20>, <&spi0_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + spi1: spi@01c06000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c06000 0x1000>; + interrupts = <11>; + clocks = <&ahb_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + emac: ethernet@01c0b000 { compatible = "allwinner,sun4i-a10-emac"; reg = <0x01c0b000 0x1000>; @@ -293,6 +338,49 @@ #size-cells = <0>; }; + usbphy: phy@01c13400 { + #phy-cells = <1>; + compatible = "allwinner,sun5i-a13-usb-phy"; + reg = <0x01c13400 0x10 0x01c14800 0x4>; + reg-names = "phy_ctrl", "pmu1"; + clocks = <&usb_clk 8>; + clock-names = "usb_phy"; + resets = <&usb_clk 1>; + reset-names = "usb1_reset"; + status = "disabled"; + }; + + ehci0: usb@01c14000 { + compatible = "allwinner,sun5i-a10s-ehci", "generic-ehci"; + reg = <0x01c14000 0x100>; + interrupts = <39>; + clocks = <&ahb_gates 1>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + ohci0: usb@01c14400 { + compatible = "allwinner,sun5i-a10s-ohci", "generic-ohci"; + reg = <0x01c14400 0x100>; + interrupts = <40>; + clocks = <&usb_clk 6>, <&ahb_gates 2>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + spi2: spi@01c17000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c17000 0x1000>; + interrupts = <12>; + clocks = <&ahb_gates 22>, <&spi2_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + intc: interrupt-controller@01c20400 { compatible = "allwinner,sun4i-a10-ic"; reg = <0x01c20400 0x400>; @@ -373,7 +461,7 @@ }; wdt: watchdog@01c20c90 { - compatible = "allwinner,sun4i-wdt"; + compatible = "allwinner,sun4i-a10-wdt"; reg = <0x01c20c90 0x10>; }; diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts b/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts index fe2ce0acdb06..11169d5b5b86 100644 --- a/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts +++ b/arch/arm/boot/dts/sun5i-a13-olinuxino-micro.dts @@ -14,12 +14,26 @@ /dts-v1/; /include/ "sun5i-a13.dtsi" +/include/ "sunxi-common-regulators.dtsi" / { model = "Olimex A13-Olinuxino Micro"; compatible = "olimex,a13-olinuxino-micro", "allwinner,sun5i-a13"; soc@01c00000 { + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + pinctrl@01c20800 { led_pins_olinuxinom: led_pins@0 { allwinner,pins = "PG9"; @@ -27,6 +41,13 @@ allwinner,drive = <1>; allwinner,pull = <0>; }; + + usb1_vbus_pin_olinuxinom: usb1_vbus_pin@0 { + allwinner,pins = "PG11"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; }; uart1: serial@01c28400 { @@ -65,4 +86,10 @@ default-state = "on"; }; }; + + reg_usb1_vbus: usb1-vbus { + pinctrl-0 = <&usb1_vbus_pin_olinuxinom>; + gpio = <&pio 6 11 0>; + status = "okay"; + }; }; diff --git a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts index a4ba5ff010cf..7a9187bbeb28 100644 --- a/arch/arm/boot/dts/sun5i-a13-olinuxino.dts +++ b/arch/arm/boot/dts/sun5i-a13-olinuxino.dts @@ -13,12 +13,26 @@ /dts-v1/; /include/ "sun5i-a13.dtsi" +/include/ "sunxi-common-regulators.dtsi" / { model = "Olimex A13-Olinuxino"; compatible = "olimex,a13-olinuxino", "allwinner,sun5i-a13"; soc@01c00000 { + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + pinctrl@01c20800 { led_pins_olinuxino: led_pins@0 { allwinner,pins = "PG9"; @@ -26,6 +40,13 @@ allwinner,drive = <1>; allwinner,pull = <0>; }; + + usb1_vbus_pin_olinuxino: usb1_vbus_pin@0 { + allwinner,pins = "PG11"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; }; uart1: serial@01c28400 { @@ -63,4 +84,10 @@ default-state = "on"; }; }; + + reg_usb1_vbus: usb1-vbus { + pinctrl-0 = <&usb1_vbus_pin_olinuxino>; + gpio = <&pio 6 11 0>; + status = "okay"; + }; }; diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/sun5i-a13.dtsi index 3490ef9ec603..f01c315bdc4b 100644 --- a/arch/arm/boot/dts/sun5i-a13.dtsi +++ b/arch/arm/boot/dts/sun5i-a13.dtsi @@ -16,6 +16,11 @@ / { interrupt-parent = <&intc>; + aliases { + serial0 = &uart1; + serial1 = &uart3; + }; + cpus { #address-cells = <1>; #size-cells = <0>; @@ -47,44 +52,48 @@ clock-frequency = <0>; }; - osc24M: osc24M@01c20050 { + osc24M: clk@01c20050 { #clock-cells = <0>; - compatible = "allwinner,sun4i-osc-clk"; + compatible = "allwinner,sun4i-a10-osc-clk"; reg = <0x01c20050 0x4>; clock-frequency = <24000000>; + clock-output-names = "osc24M"; }; - osc32k: osc32k { + osc32k: clk@0 { #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <32768>; + clock-output-names = "osc32k"; }; - pll1: pll1@01c20000 { + pll1: clk@01c20000 { #clock-cells = <0>; - compatible = "allwinner,sun4i-pll1-clk"; + compatible = "allwinner,sun4i-a10-pll1-clk"; reg = <0x01c20000 0x4>; clocks = <&osc24M>; + clock-output-names = "pll1"; }; - pll4: pll4@01c20018 { + pll4: clk@01c20018 { #clock-cells = <0>; - compatible = "allwinner,sun4i-pll1-clk"; + compatible = "allwinner,sun4i-a10-pll1-clk"; reg = <0x01c20018 0x4>; clocks = <&osc24M>; + clock-output-names = "pll4"; }; - pll5: pll5@01c20020 { + pll5: clk@01c20020 { #clock-cells = <1>; - compatible = "allwinner,sun4i-pll5-clk"; + compatible = "allwinner,sun4i-a10-pll5-clk"; reg = <0x01c20020 0x4>; clocks = <&osc24M>; clock-output-names = "pll5_ddr", "pll5_other"; }; - pll6: pll6@01c20028 { + pll6: clk@01c20028 { #clock-cells = <1>; - compatible = "allwinner,sun4i-pll6-clk"; + compatible = "allwinner,sun4i-a10-pll6-clk"; reg = <0x01c20028 0x4>; clocks = <&osc24M>; clock-output-names = "pll6_sata", "pll6_other", "pll6"; @@ -93,21 +102,23 @@ /* dummy is 200M */ cpu: cpu@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-cpu-clk"; + compatible = "allwinner,sun4i-a10-cpu-clk"; reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>; + clock-output-names = "cpu"; }; axi: axi@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-axi-clk"; + compatible = "allwinner,sun4i-a10-axi-clk"; reg = <0x01c20054 0x4>; clocks = <&cpu>; + clock-output-names = "axi"; }; - axi_gates: axi_gates@01c2005c { + axi_gates: clk@01c2005c { #clock-cells = <1>; - compatible = "allwinner,sun4i-axi-gates-clk"; + compatible = "allwinner,sun4i-a10-axi-gates-clk"; reg = <0x01c2005c 0x4>; clocks = <&axi>; clock-output-names = "axi_dram"; @@ -115,12 +126,13 @@ ahb: ahb@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-ahb-clk"; + compatible = "allwinner,sun4i-a10-ahb-clk"; reg = <0x01c20054 0x4>; clocks = <&axi>; + clock-output-names = "ahb"; }; - ahb_gates: ahb_gates@01c20060 { + ahb_gates: clk@01c20060 { #clock-cells = <1>; compatible = "allwinner,sun5i-a13-ahb-gates-clk"; reg = <0x01c20060 0x8>; @@ -135,12 +147,13 @@ apb0: apb0@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb0-clk"; + compatible = "allwinner,sun4i-a10-apb0-clk"; reg = <0x01c20054 0x4>; clocks = <&ahb>; + clock-output-names = "apb0"; }; - apb0_gates: apb0_gates@01c20068 { + apb0_gates: clk@01c20068 { #clock-cells = <1>; compatible = "allwinner,sun5i-a13-apb0-gates-clk"; reg = <0x01c20068 0x4>; @@ -150,19 +163,21 @@ apb1_mux: apb1_mux@01c20058 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb1-mux-clk"; + compatible = "allwinner,sun4i-a10-apb1-mux-clk"; reg = <0x01c20058 0x4>; clocks = <&osc24M>, <&pll6 1>, <&osc32k>; + clock-output-names = "apb1_mux"; }; apb1: apb1@01c20058 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb1-clk"; + compatible = "allwinner,sun4i-a10-apb1-clk"; reg = <0x01c20058 0x4>; clocks = <&apb1_mux>; + clock-output-names = "apb1"; }; - apb1_gates: apb1_gates@01c2006c { + apb1_gates: clk@01c2006c { #clock-cells = <1>; compatible = "allwinner,sun5i-a13-apb1-gates-clk"; reg = <0x01c2006c 0x4>; @@ -173,7 +188,7 @@ nand_clk: clk@01c20080 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20080 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "nand"; @@ -181,7 +196,7 @@ ms_clk: clk@01c20084 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20084 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ms"; @@ -189,7 +204,7 @@ mmc0_clk: clk@01c20088 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20088 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc0"; @@ -197,7 +212,7 @@ mmc1_clk: clk@01c2008c { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c2008c 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc1"; @@ -205,7 +220,7 @@ mmc2_clk: clk@01c20090 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20090 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc2"; @@ -213,7 +228,7 @@ ts_clk: clk@01c20098 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20098 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ts"; @@ -221,7 +236,7 @@ ss_clk: clk@01c2009c { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c2009c 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ss"; @@ -229,7 +244,7 @@ spi0_clk: clk@01c200a0 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200a0 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi0"; @@ -237,7 +252,7 @@ spi1_clk: clk@01c200a4 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200a4 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi1"; @@ -245,7 +260,7 @@ spi2_clk: clk@01c200a8 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200a8 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi2"; @@ -253,15 +268,24 @@ ir0_clk: clk@01c200b0 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200b0 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ir0"; }; + usb_clk: clk@01c200cc { + #clock-cells = <1>; + #reset-cells = <1>; + compatible = "allwinner,sun5i-a13-usb-clk"; + reg = <0x01c200cc 0x4>; + clocks = <&pll6 1>; + clock-output-names = "usb_ohci0", "usb_phy"; + }; + mbus_clk: clk@01c2015c { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c2015c 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mbus"; @@ -274,6 +298,71 @@ #size-cells = <1>; ranges; + spi0: spi@01c05000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c05000 0x1000>; + interrupts = <10>; + clocks = <&ahb_gates 20>, <&spi0_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + spi1: spi@01c06000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c06000 0x1000>; + interrupts = <11>; + clocks = <&ahb_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + usbphy: phy@01c13400 { + #phy-cells = <1>; + compatible = "allwinner,sun5i-a13-usb-phy"; + reg = <0x01c13400 0x10 0x01c14800 0x4>; + reg-names = "phy_ctrl", "pmu1"; + clocks = <&usb_clk 8>; + clock-names = "usb_phy"; + resets = <&usb_clk 1>; + reset-names = "usb1_reset"; + status = "disabled"; + }; + + ehci0: usb@01c14000 { + compatible = "allwinner,sun5i-a13-ehci", "generic-ehci"; + reg = <0x01c14000 0x100>; + interrupts = <39>; + clocks = <&ahb_gates 1>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + ohci0: usb@01c14400 { + compatible = "allwinner,sun5i-a13-ohci", "generic-ohci"; + reg = <0x01c14400 0x100>; + interrupts = <40>; + clocks = <&usb_clk 6>, <&ahb_gates 2>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + spi2: spi@01c17000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c17000 0x1000>; + interrupts = <12>; + clocks = <&ahb_gates 22>, <&spi2_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + intc: interrupt-controller@01c20400 { compatible = "allwinner,sun4i-a10-ic"; reg = <0x01c20400 0x400>; @@ -336,7 +425,7 @@ }; wdt: watchdog@01c20c90 { - compatible = "allwinner,sun4i-wdt"; + compatible = "allwinner,sun4i-a10-wdt"; reg = <0x01c20c90 0x10>; }; diff --git a/arch/arm/boot/dts/sun6i-a31-colombus.dts b/arch/arm/boot/dts/sun6i-a31-colombus.dts index e5adae30899b..3898a7bce831 100644 --- a/arch/arm/boot/dts/sun6i-a31-colombus.dts +++ b/arch/arm/boot/dts/sun6i-a31-colombus.dts @@ -28,5 +28,23 @@ pinctrl-0 = <&uart0_pins_a>; status = "okay"; }; + + i2c0: i2c@01c2ac00 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_pins_a>; + status = "fail"; + }; + + i2c1: i2c@01c2b000 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_pins_a>; + status = "okay"; + }; + + i2c2: i2c@01c2b400 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_pins_a>; + status = "okay"; + }; }; }; diff --git a/arch/arm/boot/dts/sun6i-a31.dtsi b/arch/arm/boot/dts/sun6i-a31.dtsi index 38d43febda4c..d45efa74827c 100644 --- a/arch/arm/boot/dts/sun6i-a31.dtsi +++ b/arch/arm/boot/dts/sun6i-a31.dtsi @@ -16,6 +16,16 @@ / { interrupt-parent = <&gic>; + aliases { + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + }; + + cpus { #address-cells = <1>; #size-cells = <0>; @@ -60,34 +70,32 @@ clock-frequency = <24000000>; }; - osc32k: osc32k { + osc32k: clk@0 { #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <32768>; + clock-output-names = "osc32k"; }; - pll1: pll1@01c20000 { + pll1: clk@01c20000 { #clock-cells = <0>; compatible = "allwinner,sun6i-a31-pll1-clk"; reg = <0x01c20000 0x4>; clocks = <&osc24M>; + clock-output-names = "pll1"; }; - /* - * This is a dummy clock, to be used as placeholder on - * other mux clocks when a specific parent clock is not - * yet implemented. It should be dropped when the driver - * is complete. - */ - pll6: pll6 { + pll6: clk@01c20028 { #clock-cells = <0>; - compatible = "fixed-clock"; - clock-frequency = <0>; + compatible = "allwinner,sun6i-a31-pll6-clk"; + reg = <0x01c20028 0x4>; + clocks = <&osc24M>; + clock-output-names = "pll6"; }; cpu: cpu@01c20050 { #clock-cells = <0>; - compatible = "allwinner,sun4i-cpu-clk"; + compatible = "allwinner,sun4i-a10-cpu-clk"; reg = <0x01c20050 0x4>; /* @@ -97,13 +105,15 @@ * Allwinner. */ clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll1>; + clock-output-names = "cpu"; }; axi: axi@01c20050 { #clock-cells = <0>; - compatible = "allwinner,sun4i-axi-clk"; + compatible = "allwinner,sun4i-a10-axi-clk"; reg = <0x01c20050 0x4>; clocks = <&cpu>; + clock-output-names = "axi"; }; ahb1_mux: ahb1_mux@01c20054 { @@ -111,16 +121,18 @@ compatible = "allwinner,sun6i-a31-ahb1-mux-clk"; reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&axi>, <&pll6>; + clock-output-names = "ahb1_mux"; }; ahb1: ahb1@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-ahb-clk"; + compatible = "allwinner,sun4i-a10-ahb-clk"; reg = <0x01c20054 0x4>; clocks = <&ahb1_mux>; + clock-output-names = "ahb1"; }; - ahb1_gates: ahb1_gates@01c20060 { + ahb1_gates: clk@01c20060 { #clock-cells = <1>; compatible = "allwinner,sun6i-a31-ahb1-gates-clk"; reg = <0x01c20060 0x8>; @@ -143,12 +155,13 @@ apb1: apb1@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb0-clk"; + compatible = "allwinner,sun4i-a10-apb0-clk"; reg = <0x01c20054 0x4>; clocks = <&ahb1>; + clock-output-names = "apb1"; }; - apb1_gates: apb1_gates@01c20060 { + apb1_gates: clk@01c20068 { #clock-cells = <1>; compatible = "allwinner,sun6i-a31-apb1-gates-clk"; reg = <0x01c20068 0x4>; @@ -160,9 +173,10 @@ apb2_mux: apb2_mux@01c20058 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb1-mux-clk"; + compatible = "allwinner,sun4i-a10-apb1-mux-clk"; reg = <0x01c20058 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll6>, <&pll6>; + clock-output-names = "apb2_mux"; }; apb2: apb2@01c20058 { @@ -170,9 +184,10 @@ compatible = "allwinner,sun6i-a31-apb2-div-clk"; reg = <0x01c20058 0x4>; clocks = <&apb2_mux>; + clock-output-names = "apb2"; }; - apb2_gates: apb2_gates@01c2006c { + apb2_gates: clk@01c2006c { #clock-cells = <1>; compatible = "allwinner,sun6i-a31-apb2-gates-clk"; reg = <0x01c2006c 0x4>; @@ -182,6 +197,38 @@ "apb2_uart1", "apb2_uart2", "apb2_uart3", "apb2_uart4", "apb2_uart5"; }; + + spi0_clk: clk@01c200a0 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c200a0 0x4>; + clocks = <&osc24M>, <&pll6>; + clock-output-names = "spi0"; + }; + + spi1_clk: clk@01c200a4 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c200a4 0x4>; + clocks = <&osc24M>, <&pll6>; + clock-output-names = "spi1"; + }; + + spi2_clk: clk@01c200a8 { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c200a8 0x4>; + clocks = <&osc24M>, <&pll6>; + clock-output-names = "spi2"; + }; + + spi3_clk: clk@01c200ac { + #clock-cells = <0>; + compatible = "allwinner,sun4i-a10-mod0-clk"; + reg = <0x01c200ac 0x4>; + clocks = <&osc24M>, <&pll6>; + clock-output-names = "spi3"; + }; }; soc@01c00000 { @@ -218,6 +265,27 @@ allwinner,drive = <0>; allwinner,pull = <0>; }; + + i2c0_pins_a: i2c0@0 { + allwinner,pins = "PH14", "PH15"; + allwinner,function = "i2c0"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + i2c1_pins_a: i2c1@0 { + allwinner,pins = "PH16", "PH17"; + allwinner,function = "i2c1"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + i2c2_pins_a: i2c2@0 { + allwinner,pins = "PH18", "PH19"; + allwinner,function = "i2c2"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; }; ahb1_rst: reset@01c202c0 { @@ -250,7 +318,7 @@ }; wdt1: watchdog@01c20ca0 { - compatible = "allwinner,sun6i-wdt"; + compatible = "allwinner,sun6i-a31-wdt"; reg = <0x01c20ca0 0x20>; }; @@ -320,6 +388,86 @@ status = "disabled"; }; + i2c0: i2c@01c2ac00 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2ac00 0x400>; + interrupts = <0 6 4>; + clocks = <&apb2_gates 0>; + clock-frequency = <100000>; + resets = <&apb2_rst 0>; + status = "disabled"; + }; + + i2c1: i2c@01c2b000 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b000 0x400>; + interrupts = <0 7 4>; + clocks = <&apb2_gates 1>; + clock-frequency = <100000>; + resets = <&apb2_rst 1>; + status = "disabled"; + }; + + i2c2: i2c@01c2b400 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b400 0x400>; + interrupts = <0 8 4>; + clocks = <&apb2_gates 2>; + clock-frequency = <100000>; + resets = <&apb2_rst 2>; + status = "disabled"; + }; + + i2c3: i2c@01c2b800 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b800 0x400>; + interrupts = <0 9 4>; + clocks = <&apb2_gates 3>; + clock-frequency = <100000>; + resets = <&apb2_rst 3>; + status = "disabled"; + }; + + spi0: spi@01c68000 { + compatible = "allwinner,sun6i-a31-spi"; + reg = <0x01c68000 0x1000>; + interrupts = <0 65 4>; + clocks = <&ahb1_gates 20>, <&spi0_clk>; + clock-names = "ahb", "mod"; + resets = <&ahb1_rst 20>; + status = "disabled"; + }; + + spi1: spi@01c69000 { + compatible = "allwinner,sun6i-a31-spi"; + reg = <0x01c69000 0x1000>; + interrupts = <0 66 4>; + clocks = <&ahb1_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + resets = <&ahb1_rst 21>; + status = "disabled"; + }; + + spi2: spi@01c6a000 { + compatible = "allwinner,sun6i-a31-spi"; + reg = <0x01c6a000 0x1000>; + interrupts = <0 67 4>; + clocks = <&ahb1_gates 22>, <&spi2_clk>; + clock-names = "ahb", "mod"; + resets = <&ahb1_rst 22>; + status = "disabled"; + }; + + spi3: spi@01c6b000 { + compatible = "allwinner,sun6i-a31-spi"; + reg = <0x01c6b000 0x1000>; + interrupts = <0 68 4>; + clocks = <&ahb1_gates 23>, <&spi3_clk>; + clock-names = "ahb", "mod"; + resets = <&ahb1_rst 23>; + status = "disabled"; + }; + gic: interrupt-controller@01c81000 { compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; reg = <0x01c81000 0x1000>, diff --git a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts index 5c51cb8a98b0..68de89ffbdfa 100644 --- a/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts +++ b/arch/arm/boot/dts/sun7i-a20-cubieboard2.dts @@ -13,25 +13,38 @@ /dts-v1/; /include/ "sun7i-a20.dtsi" +/include/ "sunxi-common-regulators.dtsi" / { model = "Cubietech Cubieboard2"; compatible = "cubietech,cubieboard2", "allwinner,sun7i-a20"; soc@01c00000 { - emac: ethernet@01c0b000 { - pinctrl-names = "default"; - pinctrl-0 = <&emac_pins_a>; - phy = <&phy1>; + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; }; - mdio@01c0b080 { + ehci0: usb@01c14000 { status = "okay"; + }; - phy1: ethernet-phy@1 { - reg = <1>; - }; + ohci0: usb@01c14400 { + status = "okay"; + }; + + ahci: sata@01c18000 { + target-supply = <®_ahci_5v>; + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; }; pinctrl@01c20800 { @@ -60,6 +73,18 @@ pinctrl-0 = <&i2c1_pins_a>; status = "okay"; }; + + gmac: ethernet@01c50000 { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_mii_a>; + phy = <&phy1>; + phy-mode = "mii"; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; }; leds { @@ -77,4 +102,16 @@ gpios = <&pio 7 20 0>; }; }; + + reg_ahci_5v: ahci-5v { + status = "okay"; + }; + + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; + }; }; diff --git a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts index f9dcb61a5305..cb25d3c8da58 100644 --- a/arch/arm/boot/dts/sun7i-a20-cubietruck.dts +++ b/arch/arm/boot/dts/sun7i-a20-cubietruck.dts @@ -13,13 +13,48 @@ /dts-v1/; /include/ "sun7i-a20.dtsi" +/include/ "sunxi-common-regulators.dtsi" / { model = "Cubietech Cubietruck"; compatible = "cubietech,cubietruck", "allwinner,sun7i-a20"; soc@01c00000 { + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + status = "okay"; + }; + + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + ahci: sata@01c18000 { + target-supply = <®_ahci_5v>; + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; + }; + pinctrl@01c20800 { + ahci_pwr_pin_cubietruck: ahci_pwr_pin@1 { + allwinner,pins = "PH12"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + led_pins_cubietruck: led_pins@0 { allwinner,pins = "PH7", "PH11", "PH20", "PH21"; allwinner,function = "gpio_out"; @@ -51,6 +86,18 @@ pinctrl-0 = <&i2c2_pins_a>; status = "okay"; }; + + gmac: ethernet@01c50000 { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_rgmii_a>; + phy = <&phy1>; + phy-mode = "rgmii"; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; }; leds { @@ -78,4 +125,18 @@ gpios = <&pio 7 7 0>; }; }; + + reg_ahci_5v: ahci-5v { + pinctrl-0 = <&ahci_pwr_pin_cubietruck>; + gpio = <&pio 7 12 0>; + status = "okay"; + }; + + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; + }; }; diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts index ead3013f9aca..eeadf76362fa 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-micro.dts @@ -13,25 +13,55 @@ /dts-v1/; /include/ "sun7i-a20.dtsi" +/include/ "sunxi-common-regulators.dtsi" / { model = "Olimex A20-Olinuxino Micro"; compatible = "olimex,a20-olinuxino-micro", "allwinner,sun7i-a20"; + aliases { + spi0 = &spi1; + spi1 = &spi2; + }; + soc@01c00000 { - emac: ethernet@01c0b000 { + spi1: spi@01c06000 { pinctrl-names = "default"; - pinctrl-0 = <&emac_pins_a>; - phy = <&phy1>; + pinctrl-0 = <&spi1_pins_a>; status = "okay"; }; - mdio@01c0b080 { + usbphy: phy@01c13400 { + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; + }; - phy1: ethernet-phy@1 { - reg = <1>; - }; + ehci0: usb@01c14000 { + status = "okay"; + }; + + ohci0: usb@01c14400 { + status = "okay"; + }; + + spi2: spi@01c17000 { + pinctrl-names = "default"; + pinctrl-0 = <&spi2_pins_a>; + status = "okay"; + }; + + ahci: sata@01c18000 { + target-supply = <®_ahci_5v>; + status = "okay"; + }; + + ehci1: usb@01c1c000 { + status = "okay"; + }; + + ohci1: usb@01c1c400 { + status = "okay"; }; pinctrl@01c20800 { @@ -78,6 +108,18 @@ pinctrl-0 = <&i2c2_pins_a>; status = "okay"; }; + + gmac: ethernet@01c50000 { + pinctrl-names = "default"; + pinctrl-0 = <&gmac_pins_mii_a>; + phy = <&phy1>; + phy-mode = "mii"; + status = "okay"; + + phy1: ethernet-phy@1 { + reg = <1>; + }; + }; }; leds { @@ -91,4 +133,16 @@ default-state = "on"; }; }; + + reg_ahci_5v: ahci-5v { + status = "okay"; + }; + + reg_usb1_vbus: usb1-vbus { + status = "okay"; + }; + + reg_usb2_vbus: usb2-vbus { + status = "okay"; + }; }; diff --git a/arch/arm/boot/dts/sun7i-a20.dtsi b/arch/arm/boot/dts/sun7i-a20.dtsi index cadcf2f9881d..32efc105df83 100644 --- a/arch/arm/boot/dts/sun7i-a20.dtsi +++ b/arch/arm/boot/dts/sun7i-a20.dtsi @@ -17,7 +17,15 @@ interrupt-parent = <&gic>; aliases { - ethernet0 = &emac; + ethernet0 = &gmac; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + serial3 = &uart3; + serial4 = &uart4; + serial5 = &uart5; + serial6 = &uart6; + serial7 = &uart7; }; cpus { @@ -41,16 +49,25 @@ reg = <0x40000000 0x80000000>; }; + timer { + compatible = "arm,armv7-timer"; + interrupts = <1 13 0xf08>, + <1 14 0xf08>, + <1 11 0xf08>, + <1 10 0xf08>; + }; + clocks { #address-cells = <1>; #size-cells = <1>; ranges; - osc24M: osc24M@01c20050 { + osc24M: clk@01c20050 { #clock-cells = <0>; - compatible = "allwinner,sun4i-osc-clk"; + compatible = "allwinner,sun4i-a10-osc-clk"; reg = <0x01c20050 0x4>; clock-frequency = <24000000>; + clock-output-names = "osc24M"; }; osc32k: clk@0 { @@ -60,31 +77,33 @@ clock-output-names = "osc32k"; }; - pll1: pll1@01c20000 { + pll1: clk@01c20000 { #clock-cells = <0>; - compatible = "allwinner,sun4i-pll1-clk"; + compatible = "allwinner,sun4i-a10-pll1-clk"; reg = <0x01c20000 0x4>; clocks = <&osc24M>; + clock-output-names = "pll1"; }; - pll4: pll4@01c20018 { + pll4: clk@01c20018 { #clock-cells = <0>; - compatible = "allwinner,sun4i-pll1-clk"; + compatible = "allwinner,sun4i-a10-pll1-clk"; reg = <0x01c20018 0x4>; clocks = <&osc24M>; + clock-output-names = "pll4"; }; - pll5: pll5@01c20020 { + pll5: clk@01c20020 { #clock-cells = <1>; - compatible = "allwinner,sun4i-pll5-clk"; + compatible = "allwinner,sun4i-a10-pll5-clk"; reg = <0x01c20020 0x4>; clocks = <&osc24M>; clock-output-names = "pll5_ddr", "pll5_other"; }; - pll6: pll6@01c20028 { + pll6: clk@01c20028 { #clock-cells = <1>; - compatible = "allwinner,sun4i-pll6-clk"; + compatible = "allwinner,sun4i-a10-pll6-clk"; reg = <0x01c20028 0x4>; clocks = <&osc24M>; clock-output-names = "pll6_sata", "pll6_other", "pll6"; @@ -92,26 +111,29 @@ cpu: cpu@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-cpu-clk"; + compatible = "allwinner,sun4i-a10-cpu-clk"; reg = <0x01c20054 0x4>; clocks = <&osc32k>, <&osc24M>, <&pll1>, <&pll6 1>; + clock-output-names = "cpu"; }; axi: axi@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-axi-clk"; + compatible = "allwinner,sun4i-a10-axi-clk"; reg = <0x01c20054 0x4>; clocks = <&cpu>; + clock-output-names = "axi"; }; ahb: ahb@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-ahb-clk"; + compatible = "allwinner,sun4i-a10-ahb-clk"; reg = <0x01c20054 0x4>; clocks = <&axi>; + clock-output-names = "ahb"; }; - ahb_gates: ahb_gates@01c20060 { + ahb_gates: clk@01c20060 { #clock-cells = <1>; compatible = "allwinner,sun7i-a20-ahb-gates-clk"; reg = <0x01c20060 0x8>; @@ -133,12 +155,13 @@ apb0: apb0@01c20054 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb0-clk"; + compatible = "allwinner,sun4i-a10-apb0-clk"; reg = <0x01c20054 0x4>; clocks = <&ahb>; + clock-output-names = "apb0"; }; - apb0_gates: apb0_gates@01c20068 { + apb0_gates: clk@01c20068 { #clock-cells = <1>; compatible = "allwinner,sun7i-a20-apb0-gates-clk"; reg = <0x01c20068 0x4>; @@ -151,19 +174,21 @@ apb1_mux: apb1_mux@01c20058 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb1-mux-clk"; + compatible = "allwinner,sun4i-a10-apb1-mux-clk"; reg = <0x01c20058 0x4>; clocks = <&osc24M>, <&pll6 1>, <&osc32k>; + clock-output-names = "apb1_mux"; }; apb1: apb1@01c20058 { #clock-cells = <0>; - compatible = "allwinner,sun4i-apb1-clk"; + compatible = "allwinner,sun4i-a10-apb1-clk"; reg = <0x01c20058 0x4>; clocks = <&apb1_mux>; + clock-output-names = "apb1"; }; - apb1_gates: apb1_gates@01c2006c { + apb1_gates: clk@01c2006c { #clock-cells = <1>; compatible = "allwinner,sun7i-a20-apb1-gates-clk"; reg = <0x01c2006c 0x4>; @@ -178,7 +203,7 @@ nand_clk: clk@01c20080 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20080 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "nand"; @@ -186,7 +211,7 @@ ms_clk: clk@01c20084 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20084 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ms"; @@ -194,7 +219,7 @@ mmc0_clk: clk@01c20088 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20088 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc0"; @@ -202,7 +227,7 @@ mmc1_clk: clk@01c2008c { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c2008c 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc1"; @@ -210,7 +235,7 @@ mmc2_clk: clk@01c20090 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20090 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc2"; @@ -218,7 +243,7 @@ mmc3_clk: clk@01c20094 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20094 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "mmc3"; @@ -226,7 +251,7 @@ ts_clk: clk@01c20098 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c20098 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ts"; @@ -234,7 +259,7 @@ ss_clk: clk@01c2009c { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c2009c 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ss"; @@ -242,7 +267,7 @@ spi0_clk: clk@01c200a0 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200a0 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi0"; @@ -250,7 +275,7 @@ spi1_clk: clk@01c200a4 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200a4 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi1"; @@ -258,7 +283,7 @@ spi2_clk: clk@01c200a8 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200a8 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi2"; @@ -266,7 +291,7 @@ pata_clk: clk@01c200ac { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200ac 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "pata"; @@ -274,7 +299,7 @@ ir0_clk: clk@01c200b0 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200b0 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ir0"; @@ -282,15 +307,24 @@ ir1_clk: clk@01c200b4 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200b4 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "ir1"; }; + usb_clk: clk@01c200cc { + #clock-cells = <1>; + #reset-cells = <1>; + compatible = "allwinner,sun4i-a10-usb-clk"; + reg = <0x01c200cc 0x4>; + clocks = <&pll6 1>; + clock-output-names = "usb_ohci0", "usb_ohci1", "usb_phy"; + }; + spi3_clk: clk@01c200d4 { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c200d4 0x4>; clocks = <&osc24M>, <&pll6 1>, <&pll5 1>; clock-output-names = "spi3"; @@ -298,13 +332,41 @@ mbus_clk: clk@01c2015c { #clock-cells = <0>; - compatible = "allwinner,sun4i-mod0-clk"; + compatible = "allwinner,sun4i-a10-mod0-clk"; reg = <0x01c2015c 0x4>; clocks = <&osc24M>, <&pll6 2>, <&pll5 1>; clock-output-names = "mbus"; }; /* + * The following two are dummy clocks, placeholders used in the gmac_tx + * clock. The gmac driver will choose one parent depending on the PHY + * interface mode, using clk_set_rate auto-reparenting. + * The actual TX clock rate is not controlled by the gmac_tx clock. + */ + mii_phy_tx_clk: clk@2 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <25000000>; + clock-output-names = "mii_phy_tx"; + }; + + gmac_int_tx_clk: clk@3 { + #clock-cells = <0>; + compatible = "fixed-clock"; + clock-frequency = <125000000>; + clock-output-names = "gmac_int_tx"; + }; + + gmac_tx_clk: clk@01c20164 { + #clock-cells = <0>; + compatible = "allwinner,sun7i-a20-gmac-clk"; + reg = <0x01c20164 0x4>; + clocks = <&mii_phy_tx_clk>, <&gmac_int_tx_clk>; + clock-output-names = "gmac_tx"; + }; + + /* * Dummy clock used by output clocks */ osc24M_32k: clk@1 { @@ -347,6 +409,28 @@ interrupts = <0 0 4>; }; + spi0: spi@01c05000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c05000 0x1000>; + interrupts = <0 10 4>; + clocks = <&ahb_gates 20>, <&spi0_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + spi1: spi@01c06000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c06000 0x1000>; + interrupts = <0 11 4>; + clocks = <&ahb_gates 21>, <&spi1_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + emac: ethernet@01c0b000 { compatible = "allwinner,sun4i-a10-emac"; reg = <0x01c0b000 0x1000>; @@ -363,6 +447,88 @@ #size-cells = <0>; }; + usbphy: phy@01c13400 { + #phy-cells = <1>; + compatible = "allwinner,sun7i-a20-usb-phy"; + reg = <0x01c13400 0x10 0x01c14800 0x4 0x01c1c800 0x4>; + reg-names = "phy_ctrl", "pmu1", "pmu2"; + clocks = <&usb_clk 8>; + clock-names = "usb_phy"; + resets = <&usb_clk 1>, <&usb_clk 2>; + reset-names = "usb1_reset", "usb2_reset"; + status = "disabled"; + }; + + ehci0: usb@01c14000 { + compatible = "allwinner,sun7i-a20-ehci", "generic-ehci"; + reg = <0x01c14000 0x100>; + interrupts = <0 39 4>; + clocks = <&ahb_gates 1>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + ohci0: usb@01c14400 { + compatible = "allwinner,sun7i-a20-ohci", "generic-ohci"; + reg = <0x01c14400 0x100>; + interrupts = <0 64 4>; + clocks = <&usb_clk 6>, <&ahb_gates 2>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + spi2: spi@01c17000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c17000 0x1000>; + interrupts = <0 12 4>; + clocks = <&ahb_gates 22>, <&spi2_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + ahci: sata@01c18000 { + compatible = "allwinner,sun4i-a10-ahci"; + reg = <0x01c18000 0x1000>; + interrupts = <0 56 4>; + clocks = <&pll6 0>, <&ahb_gates 25>; + status = "disabled"; + }; + + ehci1: usb@01c1c000 { + compatible = "allwinner,sun7i-a20-ehci", "generic-ehci"; + reg = <0x01c1c000 0x100>; + interrupts = <0 40 4>; + clocks = <&ahb_gates 3>; + phys = <&usbphy 2>; + phy-names = "usb"; + status = "disabled"; + }; + + ohci1: usb@01c1c400 { + compatible = "allwinner,sun7i-a20-ohci", "generic-ohci"; + reg = <0x01c1c400 0x100>; + interrupts = <0 65 4>; + clocks = <&usb_clk 7>, <&ahb_gates 4>; + phys = <&usbphy 2>; + phy-names = "usb"; + status = "disabled"; + }; + + spi3: spi@01c1f000 { + compatible = "allwinner,sun4i-a10-spi"; + reg = <0x01c1f000 0x1000>; + interrupts = <0 50 4>; + clocks = <&ahb_gates 23>, <&spi3_clk>; + clock-names = "ahb", "mod"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + pio: pinctrl@01c20800 { compatible = "allwinner,sun7i-a20-pinctrl"; reg = <0x01c20800 0x400>; @@ -381,6 +547,13 @@ allwinner,pull = <0>; }; + uart2_pins_a: uart2@0 { + allwinner,pins = "PI16", "PI17", "PI18", "PI19"; + allwinner,function = "uart2"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + uart6_pins_a: uart6@0 { allwinner,pins = "PI12", "PI13"; allwinner,function = "uart6"; @@ -440,6 +613,46 @@ allwinner,drive = <0>; allwinner,pull = <0>; }; + + gmac_pins_mii_a: gmac_mii@0 { + allwinner,pins = "PA0", "PA1", "PA2", + "PA3", "PA4", "PA5", "PA6", + "PA7", "PA8", "PA9", "PA10", + "PA11", "PA12", "PA13", "PA14", + "PA15", "PA16"; + allwinner,function = "gmac"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + gmac_pins_rgmii_a: gmac_rgmii@0 { + allwinner,pins = "PA0", "PA1", "PA2", + "PA3", "PA4", "PA5", "PA6", + "PA7", "PA8", "PA10", + "PA11", "PA12", "PA13", + "PA15", "PA16"; + allwinner,function = "gmac"; + /* + * data lines in RGMII mode use DDR mode + * and need a higher signal drive strength + */ + allwinner,drive = <3>; + allwinner,pull = <0>; + }; + + spi1_pins_a: spi1@0 { + allwinner,pins = "PI16", "PI17", "PI18", "PI19"; + allwinner,function = "spi1"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + spi2_pins_a: spi2@0 { + allwinner,pins = "PC19", "PC20", "PC21", "PC22"; + allwinner,function = "spi2"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; }; timer@01c20c00 { @@ -455,7 +668,7 @@ }; wdt: watchdog@01c20c90 { - compatible = "allwinner,sun4i-wdt"; + compatible = "allwinner,sun4i-a10-wdt"; reg = <0x01c20c90 0x10>; }; @@ -601,6 +814,21 @@ status = "disabled"; }; + gmac: ethernet@01c50000 { + compatible = "allwinner,sun7i-a20-gmac"; + reg = <0x01c50000 0x10000>; + interrupts = <0 85 4>; + interrupt-names = "macirq"; + clocks = <&ahb_gates 49>, <&gmac_tx_clk>; + clock-names = "stmmaceth", "allwinner_gmac_tx"; + snps,pbl = <2>; + snps,fixed-burst; + snps,force_sf_dma_mode; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + hstimer@01c60000 { compatible = "allwinner,sun7i-a20-hstimer"; reg = <0x01c60000 0x1000>; diff --git a/arch/arm/boot/dts/sunxi-common-regulators.dtsi b/arch/arm/boot/dts/sunxi-common-regulators.dtsi new file mode 100644 index 000000000000..18eeac0670b9 --- /dev/null +++ b/arch/arm/boot/dts/sunxi-common-regulators.dtsi @@ -0,0 +1,75 @@ +/* + * sunxi boards common regulator (ahci target power supply, usb-vbus) code + * + * Copyright 2014 - Hans de Goede <hdegoede@redhat.com> + * + * The code contained herein is licensed under the GNU General Public + * License. You may obtain a copy of the GNU General Public License + * Version 2 or later at the following locations: + * + * http://www.opensource.org/licenses/gpl-license.html + * http://www.gnu.org/copyleft/gpl.html + */ + +/ { + soc@01c00000 { + pio: pinctrl@01c20800 { + ahci_pwr_pin_a: ahci_pwr_pin@0 { + allwinner,pins = "PB8"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + usb1_vbus_pin_a: usb1_vbus_pin@0 { + allwinner,pins = "PH6"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + + usb2_vbus_pin_a: usb2_vbus_pin@0 { + allwinner,pins = "PH3"; + allwinner,function = "gpio_out"; + allwinner,drive = <0>; + allwinner,pull = <0>; + }; + }; + }; + + reg_ahci_5v: ahci-5v { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&ahci_pwr_pin_a>; + regulator-name = "ahci-5v"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&pio 1 8 0>; + status = "disabled"; + }; + + reg_usb1_vbus: usb1-vbus { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&usb1_vbus_pin_a>; + regulator-name = "usb1-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&pio 7 6 0>; + status = "disabled"; + }; + + reg_usb2_vbus: usb2-vbus { + compatible = "regulator-fixed"; + pinctrl-names = "default"; + pinctrl-0 = <&usb2_vbus_pin_a>; + regulator-name = "usb2-vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + enable-active-high; + gpio = <&pio 7 3 0>; + status = "disabled"; + }; +}; diff --git a/arch/arm/boot/dts/tegra114-dalmore.dts b/arch/arm/boot/dts/tegra114-dalmore.dts index eb54353975bc..a288a12823ed 100644 --- a/arch/arm/boot/dts/tegra114-dalmore.dts +++ b/arch/arm/boot/dts/tegra114-dalmore.dts @@ -1,3 +1,8 @@ +/* + * This dts file supports Dalmore A04. + * Other board revisions are not supported + */ + /dts-v1/; #include <dt-bindings/input/input.h> @@ -733,12 +738,10 @@ nvidia,pins = "drive_gma"; nvidia,high-speed-mode = <TEGRA_PIN_ENABLE>; nvidia,schmitt = <TEGRA_PIN_DISABLE>; - nvidia,low-power-mode = <TEGRA_PIN_LP_DRIVE_DIV_1>; nvidia,pull-down-strength = <2>; nvidia,pull-up-strength = <1>; nvidia,slew-rate-rising = <TEGRA_PIN_SLEW_RATE_FASTEST>; nvidia,slew-rate-falling = <TEGRA_PIN_SLEW_RATE_FASTEST>; - nvidia,drive-type = <1>; }; }; }; diff --git a/arch/arm/boot/dts/tegra114.dtsi b/arch/arm/boot/dts/tegra114.dtsi index 44ec401ec366..fdc559ab2db3 100644 --- a/arch/arm/boot/dts/tegra114.dtsi +++ b/arch/arm/boot/dts/tegra114.dtsi @@ -604,7 +604,7 @@ clocks = <&tegra_car TEGRA114_CLK_SDMMC1>; resets = <&tegra_car 14>; reset-names = "sdhci"; - status = "disable"; + status = "disabled"; }; sdhci@78000200 { @@ -614,7 +614,7 @@ clocks = <&tegra_car TEGRA114_CLK_SDMMC2>; resets = <&tegra_car 9>; reset-names = "sdhci"; - status = "disable"; + status = "disabled"; }; sdhci@78000400 { @@ -624,7 +624,7 @@ clocks = <&tegra_car TEGRA114_CLK_SDMMC3>; resets = <&tegra_car 69>; reset-names = "sdhci"; - status = "disable"; + status = "disabled"; }; sdhci@78000600 { @@ -634,7 +634,7 @@ clocks = <&tegra_car TEGRA114_CLK_SDMMC4>; resets = <&tegra_car 15>; reset-names = "sdhci"; - status = "disable"; + status = "disabled"; }; usb@7d000000 { diff --git a/arch/arm/boot/dts/tegra124-venice2.dts b/arch/arm/boot/dts/tegra124-venice2.dts index 0b54743c2621..c17283c04598 100644 --- a/arch/arm/boot/dts/tegra124-venice2.dts +++ b/arch/arm/boot/dts/tegra124-venice2.dts @@ -8,15 +8,29 @@ compatible = "nvidia,venice2", "nvidia,tegra124"; aliases { - rtc0 = "/i2c@7000d000/as3722@40"; - rtc1 = "/rtc@7000e000"; + rtc0 = "/i2c@0,7000d000/pmic@40"; + rtc1 = "/rtc@0,7000e000"; }; memory { - reg = <0x80000000 0x80000000>; + reg = <0x0 0x80000000 0x0 0x80000000>; }; - pinmux: pinmux@70000868 { + host1x@0,50000000 { + sor@0,54540000 { + status = "okay"; + + nvidia,dpaux = <&dpaux>; + nvidia,panel = <&panel>; + }; + + dpaux: dpaux@0,545c0000 { + vdd-supply = <&vdd_3v3_panel>; + status = "okay"; + }; + }; + + pinmux: pinmux@0,70000868 { pinctrl-names = "default"; pinctrl-0 = <&pinmux_default>; @@ -397,19 +411,11 @@ nvidia,enable-input = <TEGRA_PIN_ENABLE>; }; usb_vbus_en0_pn4 { - nvidia,pins = "usb_vbus_en0_pn4"; - nvidia,function = "usb"; - nvidia,enable-input = <TEGRA_PIN_ENABLE>; - nvidia,pull = <TEGRA_PIN_PULL_UP>; - nvidia,tristate = <TEGRA_PIN_DISABLE>; - nvidia,lock = <TEGRA_PIN_DISABLE>; - nvidia,open-drain = <TEGRA_PIN_ENABLE>; - }; - usb_vbus_en1_pn5 { - nvidia,pins = "usb_vbus_en1_pn5"; + nvidia,pins = "usb_vbus_en0_pn4", + "usb_vbus_en1_pn5"; nvidia,function = "usb"; nvidia,enable-input = <TEGRA_PIN_ENABLE>; - nvidia,pull = <TEGRA_PIN_PULL_UP>; + nvidia,pull = <TEGRA_PIN_PULL_NONE>; nvidia,tristate = <TEGRA_PIN_DISABLE>; nvidia,lock = <TEGRA_PIN_DISABLE>; nvidia,open-drain = <TEGRA_PIN_ENABLE>; @@ -565,15 +571,15 @@ }; }; - serial@70006000 { + serial@0,70006000 { status = "okay"; }; - pwm: pwm@7000a000 { + pwm: pwm@0,7000a000 { status = "okay"; }; - i2c@7000c000 { + i2c@0,7000c000 { status = "okay"; clock-frequency = <100000>; @@ -585,30 +591,32 @@ }; }; - i2c@7000c400 { + i2c@0,7000c400 { status = "okay"; clock-frequency = <100000>; }; - i2c@7000c500 { + i2c@0,7000c500 { status = "okay"; clock-frequency = <100000>; }; - i2c@7000c700 { + i2c@0,7000c700 { status = "okay"; clock-frequency = <100000>; }; - i2c@7000d000 { + i2c@0,7000d000 { status = "okay"; clock-frequency = <400000>; - as3722: as3722@40 { + pmic: pmic@40 { compatible = "ams,as3722"; reg = <0x40>; interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; + ams,system-power-controller; + #interrupt-cells = <2>; interrupt-controller; @@ -643,19 +651,19 @@ }; regulators { - vsup-sd2-supply = <&vdd_ac_bat_reg>; - vsup-sd3-supply = <&vdd_ac_bat_reg>; - vsup-sd4-supply = <&vdd_ac_bat_reg>; - vsup-sd5-supply = <&vdd_ac_bat_reg>; - vin-ldo0-supply = <&as3722_sd2>; - vin-ldo1-6-supply = <&vdd_ac_bat_reg>; - vin-ldo2-5-7-supply = <&as3722_sd5>; - vin-ldo3-4-supply = <&vdd_ac_bat_reg>; - vin-ldo9-10-supply = <&vdd_ac_bat_reg>; - vin-ldo11-supply = <&vdd_ac_bat_reg>; + vsup-sd2-supply = <&vdd_5v0_sys>; + vsup-sd3-supply = <&vdd_5v0_sys>; + vsup-sd4-supply = <&vdd_5v0_sys>; + vsup-sd5-supply = <&vdd_5v0_sys>; + vin-ldo0-supply = <&vdd_1v35_lp0>; + vin-ldo1-6-supply = <&vdd_3v3_run>; + vin-ldo2-5-7-supply = <&vddio_1v8>; + vin-ldo3-4-supply = <&vdd_3v3_sys>; + vin-ldo9-10-supply = <&vdd_5v0_sys>; + vin-ldo11-supply = <&vdd_3v3_run>; sd0 { - regulator-name = "vdd-cpu"; + regulator-name = "+VDD_CPU_AP"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1400000>; regulator-min-microamp = <3500000>; @@ -666,7 +674,7 @@ }; sd1 { - regulator-name = "vdd-core"; + regulator-name = "+VDD_CORE"; regulator-min-microvolt = <700000>; regulator-max-microvolt = <1350000>; regulator-min-microamp = <2500000>; @@ -676,8 +684,8 @@ ams,external-control = <1>; }; - as3722_sd2: sd2 { - regulator-name = "vddio-ddr"; + vdd_1v35_lp0: sd2 { + regulator-name = "+1.35V_LP0(sd2)"; regulator-min-microvolt = <1350000>; regulator-max-microvolt = <1350000>; regulator-always-on; @@ -685,7 +693,7 @@ }; sd3 { - regulator-name = "vddio-ddr-2phase"; + regulator-name = "+1.35V_LP0(sd3)"; regulator-min-microvolt = <1350000>; regulator-max-microvolt = <1350000>; regulator-always-on; @@ -693,15 +701,13 @@ }; sd4 { - regulator-name = "avdd-pex-sata"; + regulator-name = "+1.05V_RUN"; regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; - regulator-boot-on; - regulator-always-on; }; - as3722_sd5: sd5 { - regulator-name = "vddio-sys"; + vddio_1v8: sd5 { + regulator-name = "+1.8V_VDDIO"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; regulator-boot-on; @@ -709,7 +715,7 @@ }; sd6 { - regulator-name = "vdd-gpu"; + regulator-name = "+VDD_GPU_AP"; regulator-min-microvolt = <650000>; regulator-max-microvolt = <1200000>; regulator-min-microamp = <3500000>; @@ -719,7 +725,7 @@ }; ldo0 { - regulator-name = "avdd_pll"; + regulator-name = "+1.05V_RUN_AVDD"; regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; regulator-boot-on; @@ -728,13 +734,13 @@ }; ldo1 { - regulator-name = "run-cam-1.8"; + regulator-name = "+1.8V_RUN_CAM"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; ldo2 { - regulator-name = "gen-avdd,vddio-hsic"; + regulator-name = "+1.2V_GEN_AVDD"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; regulator-boot-on; @@ -742,7 +748,7 @@ }; ldo3 { - regulator-name = "vdd-rtc"; + regulator-name = "+1.00V_LP0_VDD_RTC"; regulator-min-microvolt = <1000000>; regulator-max-microvolt = <1000000>; regulator-boot-on; @@ -750,48 +756,44 @@ ams,enable-tracking; }; - ldo4 { - regulator-name = "vdd-cam"; + vdd_run_cam: ldo4 { + regulator-name = "+3.3V_RUN_CAM"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; - regulator-boot-on; - regulator-always-on; }; ldo5 { - regulator-name = "vdd-cam-front"; + regulator-name = "+1.2V_RUN_CAM_FRONT"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1200000>; }; - ldo6 { - regulator-name = "vddio-sdmmc3"; + vddio_sdmmc3: ldo6 { + regulator-name = "+VDDIO_SDMMC3"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <3300000>; - regulator-boot-on; - regulator-always-on; }; ldo7 { - regulator-name = "vdd-cam-rear"; + regulator-name = "+1.05V_RUN_CAM_REAR"; regulator-min-microvolt = <1050000>; regulator-max-microvolt = <1050000>; }; ldo9 { - regulator-name = "vdd-touch"; + regulator-name = "+2.8V_RUN_TOUCH"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; }; ldo10 { - regulator-name = "vdd-cam-af"; + regulator-name = "+2.8V_RUN_CAM_AF"; regulator-min-microvolt = <2800000>; regulator-max-microvolt = <2800000>; }; ldo11 { - regulator-name = "vpp-fuse"; + regulator-name = "+1.8V_RUN_VPP_FUSE"; regulator-min-microvolt = <1800000>; regulator-max-microvolt = <1800000>; }; @@ -799,7 +801,7 @@ }; }; - spi@7000d400 { + spi@0,7000d400 { status = "okay"; cros-ec@0 { @@ -905,7 +907,17 @@ }; }; - pmc@7000e400 { + spi@0,7000da00 { + status = "okay"; + spi-max-frequency = <25000000>; + spi-flash@0 { + compatible = "winbond,w25q32dw"; + reg = <0>; + spi-max-frequency = <20000000>; + }; + }; + + pmc@0,7000e400 { nvidia,invert-interrupt; nvidia,suspend-mode = <1>; nvidia,cpu-pwr-good-time = <500>; @@ -916,24 +928,63 @@ nvidia,sys-clock-req-active-high; }; - sdhci@700b0400 { + sdhci@0,700b0400 { cd-gpios = <&gpio TEGRA_GPIO(V, 2) GPIO_ACTIVE_HIGH>; power-gpios = <&gpio TEGRA_GPIO(R, 0) GPIO_ACTIVE_HIGH>; status = "okay"; bus-width = <4>; + vmmc-supply = <&vddio_sdmmc3>; }; - sdhci@700b0600 { + sdhci@0,700b0600 { status = "okay"; bus-width = <8>; }; - ahub@70300000 { - i2s@70301100 { + ahub@0,70300000 { + i2s@0,70301100 { status = "okay"; }; }; + usb@0,7d000000 { + status = "okay"; + }; + + usb-phy@0,7d000000 { + status = "okay"; + vbus-supply = <&vdd_usb1_vbus>; + }; + + usb@0,7d004000 { + status = "okay"; + }; + + usb-phy@0,7d004000 { + status = "okay"; + vbus-supply = <&vdd_run_cam>; + }; + + usb@0,7d008000 { + status = "okay"; + }; + + usb-phy@0,7d008000 { + status = "okay"; + vbus-supply = <&vdd_usb3_vbus>; + }; + + backlight: backlight { + compatible = "pwm-backlight"; + + enable-gpios = <&gpio TEGRA_GPIO(H, 2) GPIO_ACTIVE_HIGH>; + power-supply = <&vdd_led>; + pwms = <&pwm 1 1000000>; + + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + }; + clocks { compatible = "simple-bus"; #address-cells = <1>; @@ -941,7 +992,7 @@ clk32k_in: clock@0 { compatible = "fixed-clock"; - reg=<0>; + reg = <0>; #clock-cells = <0>; clock-frequency = <32768>; }; @@ -959,104 +1010,140 @@ }; }; + panel: panel { + compatible = "lg,lp129qe", "simple-panel"; + + backlight = <&backlight>; + ddc-i2c-bus = <&dpaux>; + }; + regulators { compatible = "simple-bus"; #address-cells = <1>; #size-cells = <0>; - vdd_ac_bat_reg: regulator@0 { + vdd_mux: regulator@0 { compatible = "regulator-fixed"; reg = <0>; - regulator-name = "vdd_ac_bat"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; + regulator-name = "+VDD_MUX"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; regulator-always-on; + regulator-boot-on; }; - vdd_3v3_reg: regulator@1 { + vdd_5v0_sys: regulator@1 { compatible = "regulator-fixed"; reg = <1>; - regulator-name = "vdd_3v3"; - regulator-min-microvolt = <3300000>; - regulator-max-microvolt = <3300000>; + regulator-name = "+5V_SYS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; regulator-always-on; regulator-boot-on; - enable-active-high; - gpio = <&as3722 1 GPIO_ACTIVE_HIGH>; + vin-supply = <&vdd_mux>; }; - vdd_3v3_modem_reg: regulator@2 { + vdd_3v3_sys: regulator@2 { compatible = "regulator-fixed"; reg = <2>; - regulator-name = "vdd-modem-3v3"; + regulator-name = "+3.3V_SYS"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - enable-active-high; - gpio = <&as3722 2 GPIO_ACTIVE_HIGH>; + regulator-always-on; + regulator-boot-on; + vin-supply = <&vdd_mux>; }; - vdd_hdmi_5v0_reg: regulator@3 { + vdd_3v3_run: regulator@3 { compatible = "regulator-fixed"; reg = <3>; - regulator-name = "vdd-hdmi-5v0"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; + regulator-name = "+3.3V_RUN"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pmic 1 GPIO_ACTIVE_HIGH>; enable-active-high; - gpio = <&gpio TEGRA_GPIO(K, 6) GPIO_ACTIVE_HIGH>; + vin-supply = <&vdd_3v3_sys>; }; - vdd_bl_reg: regulator@4 { + vdd_3v3_hdmi: regulator@4 { compatible = "regulator-fixed"; reg = <4>; - regulator-name = "vdd-bl"; + regulator-name = "+3.3V_AVDD_HDMI_AP_GATED"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; - gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_LOW>; + vin-supply = <&vdd_3v3_run>; }; - vdd_ts_sw_5v0: regulator@5 { + vdd_led: regulator@5 { compatible = "regulator-fixed"; reg = <5>; - regulator-name = "vdd_ts_sw"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; + regulator-name = "+VDD_LED"; + gpio = <&gpio TEGRA_GPIO(P, 2) GPIO_ACTIVE_HIGH>; enable-active-high; - regulator-boot-on; - gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_LOW>; + vin-supply = <&vdd_mux>; }; - usb1_vbus_reg: regulator@6 { + vdd_5v0_ts: regulator@6 { compatible = "regulator-fixed"; reg = <6>; - regulator-name = "usb1_vbus"; + regulator-name = "+5V_VDD_TS_SW"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; regulator-boot-on; + gpio = <&gpio TEGRA_GPIO(K, 1) GPIO_ACTIVE_HIGH>; enable-active-high; - gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>; - gpio-open-drain; + vin-supply = <&vdd_5v0_sys>; }; - usb3_vbus_reg: regulator@7 { + vdd_usb1_vbus: regulator@7 { compatible = "regulator-fixed"; reg = <7>; - regulator-name = "usb3_vbus"; + regulator-name = "+5V_USB_HS"; regulator-min-microvolt = <5000000>; regulator-max-microvolt = <5000000>; - regulator-boot-on; + gpio = <&gpio TEGRA_GPIO(N, 4) GPIO_ACTIVE_HIGH>; enable-active-high; - gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>; gpio-open-drain; + vin-supply = <&vdd_5v0_sys>; }; - panel_3v3_reg: regulator@8 { + vdd_usb3_vbus: regulator@8 { compatible = "regulator-fixed"; reg = <8>; - regulator-name = "panel_3v3"; + regulator-name = "+5V_USB_SS"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio TEGRA_GPIO(N, 5) GPIO_ACTIVE_HIGH>; + enable-active-high; + gpio-open-drain; + vin-supply = <&vdd_5v0_sys>; + }; + + vdd_3v3_panel: regulator@9 { + compatible = "regulator-fixed"; + reg = <9>; + regulator-name = "+3.3V_PANEL"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; + gpio = <&pmic 4 GPIO_ACTIVE_HIGH>; + enable-active-high; + vin-supply = <&vdd_3v3_run>; + }; + + vdd_3v3_lp0: regulator@10 { + compatible = "regulator-fixed"; + reg = <10>; + regulator-name = "+3.3V_LP0"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + /* + * TODO: find a way to wire this up with the USB EHCI + * controllers so that it can be enabled on demand. + */ + regulator-always-on; + gpio = <&pmic 2 GPIO_ACTIVE_HIGH>; enable-active-high; - gpio = <&as3722 4 GPIO_ACTIVE_HIGH>; + vin-supply = <&vdd_3v3_sys>; }; }; diff --git a/arch/arm/boot/dts/tegra124.dtsi b/arch/arm/boot/dts/tegra124.dtsi index ec0698a8354a..cf45a1a39483 100644 --- a/arch/arm/boot/dts/tegra124.dtsi +++ b/arch/arm/boot/dts/tegra124.dtsi @@ -8,22 +8,91 @@ / { compatible = "nvidia,tegra124"; interrupt-parent = <&gic>; + #address-cells = <2>; + #size-cells = <2>; + + host1x@0,50000000 { + compatible = "nvidia,tegra124-host1x", "simple-bus"; + reg = <0x0 0x50000000 0x0 0x00034000>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>, /* syncpt */ + <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; /* general */ + clocks = <&tegra_car TEGRA124_CLK_HOST1X>; + resets = <&tegra_car 28>; + reset-names = "host1x"; + + #address-cells = <2>; + #size-cells = <2>; + + ranges = <0 0x54000000 0 0x54000000 0 0x01000000>; + + dc@0,54200000 { + compatible = "nvidia,tegra124-dc"; + reg = <0x0 0x54200000 0x0 0x00040000>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_DISP1>, + <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "dc", "parent"; + resets = <&tegra_car 27>; + reset-names = "dc"; + + nvidia,head = <0>; + }; + + dc@0,54240000 { + compatible = "nvidia,tegra124-dc"; + reg = <0x0 0x54240000 0x0 0x00040000>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_DISP2>, + <&tegra_car TEGRA124_CLK_PLL_P>; + clock-names = "dc", "parent"; + resets = <&tegra_car 26>; + reset-names = "dc"; + + nvidia,head = <1>; + }; - gic: interrupt-controller@50041000 { + sor@0,54540000 { + compatible = "nvidia,tegra124-sor"; + reg = <0x0 0x54540000 0x0 0x00040000>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_SOR0>, + <&tegra_car TEGRA124_CLK_PLL_D_OUT0>, + <&tegra_car TEGRA124_CLK_PLL_DP>, + <&tegra_car TEGRA124_CLK_CLK_M>; + clock-names = "sor", "parent", "dp", "safe"; + resets = <&tegra_car 182>; + reset-names = "sor"; + status = "disabled"; + }; + + dpaux@0,545c0000 { + compatible = "nvidia,tegra124-dpaux"; + reg = <0x0 0x545c0000 0x0 0x00040000>; + interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA124_CLK_DPAUX>, + <&tegra_car TEGRA124_CLK_PLL_DP>; + clock-names = "dpaux", "parent"; + resets = <&tegra_car 181>; + reset-names = "dpaux"; + status = "disabled"; + }; + }; + + gic: interrupt-controller@0,50041000 { compatible = "arm,cortex-a15-gic"; #interrupt-cells = <3>; interrupt-controller; - reg = <0x50041000 0x1000>, - <0x50042000 0x1000>, - <0x50044000 0x2000>, - <0x50046000 0x2000>; + reg = <0x0 0x50041000 0x0 0x1000>, + <0x0 0x50042000 0x0 0x1000>, + <0x0 0x50044000 0x0 0x2000>, + <0x0 0x50046000 0x0 0x2000>; interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; }; - timer@60005000 { + timer@0,60005000 { compatible = "nvidia,tegra124-timer", "nvidia,tegra20-timer"; - reg = <0x60005000 0x400>; + reg = <0x0 0x60005000 0x0 0x400>; interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>, @@ -33,16 +102,16 @@ clocks = <&tegra_car TEGRA124_CLK_TIMER>; }; - tegra_car: clock@60006000 { + tegra_car: clock@0,60006000 { compatible = "nvidia,tegra124-car"; - reg = <0x60006000 0x1000>; + reg = <0x0 0x60006000 0x0 0x1000>; #clock-cells = <1>; #reset-cells = <1>; }; - gpio: gpio@6000d000 { + gpio: gpio@0,6000d000 { compatible = "nvidia,tegra124-gpio", "nvidia,tegra30-gpio"; - reg = <0x6000d000 0x1000>; + reg = <0x0 0x6000d000 0x0 0x1000>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>, @@ -57,9 +126,9 @@ interrupt-controller; }; - apbdma: dma@60020000 { + apbdma: dma@0,60020000 { compatible = "nvidia,tegra124-apbdma", "nvidia,tegra148-apbdma"; - reg = <0x60020000 0x1400>; + reg = <0x0 0x60020000 0x0 0x1400>; interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>, @@ -98,10 +167,10 @@ #dma-cells = <1>; }; - pinmux: pinmux@70000868 { + pinmux: pinmux@0,70000868 { compatible = "nvidia,tegra124-pinmux"; - reg = <0x70000868 0x164>, /* Pad control registers */ - <0x70003000 0x434>; /* Mux registers */ + reg = <0x0 0x70000868 0x0 0x164>, /* Pad control registers */ + <0x0 0x70003000 0x0 0x434>; /* Mux registers */ }; /* @@ -112,9 +181,9 @@ * the APB DMA based serial driver, the comptible is * "nvidia,tegra124-hsuart", "nvidia,tegra30-hsuart". */ - serial@70006000 { + serial@0,70006000 { compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart"; - reg = <0x70006000 0x40>; + reg = <0x0 0x70006000 0x0 0x40>; reg-shift = <2>; interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA124_CLK_UARTA>; @@ -125,9 +194,9 @@ status = "disabled"; }; - serial@70006040 { + serial@0,70006040 { compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart"; - reg = <0x70006040 0x40>; + reg = <0x0 0x70006040 0x0 0x40>; reg-shift = <2>; interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA124_CLK_UARTB>; @@ -138,9 +207,9 @@ status = "disabled"; }; - serial@70006200 { + serial@0,70006200 { compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart"; - reg = <0x70006200 0x40>; + reg = <0x0 0x70006200 0x0 0x40>; reg-shift = <2>; interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA124_CLK_UARTC>; @@ -151,9 +220,9 @@ status = "disabled"; }; - serial@70006300 { + serial@0,70006300 { compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart"; - reg = <0x70006300 0x40>; + reg = <0x0 0x70006300 0x0 0x40>; reg-shift = <2>; interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA124_CLK_UARTD>; @@ -164,9 +233,9 @@ status = "disabled"; }; - serial@70006400 { + serial@0,70006400 { compatible = "nvidia,tegra124-uart", "nvidia,tegra20-uart"; - reg = <0x70006400 0x40>; + reg = <0x0 0x70006400 0x0 0x40>; reg-shift = <2>; interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA124_CLK_UARTE>; @@ -177,9 +246,9 @@ status = "disabled"; }; - pwm@7000a000 { + pwm@0,7000a000 { compatible = "nvidia,tegra124-pwm", "nvidia,tegra20-pwm"; - reg = <0x7000a000 0x100>; + reg = <0x0 0x7000a000 0x0 0x100>; #pwm-cells = <2>; clocks = <&tegra_car TEGRA124_CLK_PWM>; resets = <&tegra_car 17>; @@ -187,9 +256,9 @@ status = "disabled"; }; - i2c@7000c000 { + i2c@0,7000c000 { compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c"; - reg = <0x7000c000 0x100>; + reg = <0x0 0x7000c000 0x0 0x100>; interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -202,9 +271,9 @@ status = "disabled"; }; - i2c@7000c400 { + i2c@0,7000c400 { compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c"; - reg = <0x7000c400 0x100>; + reg = <0x0 0x7000c400 0x0 0x100>; interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -217,9 +286,9 @@ status = "disabled"; }; - i2c@7000c500 { + i2c@0,7000c500 { compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c"; - reg = <0x7000c500 0x100>; + reg = <0x0 0x7000c500 0x0 0x100>; interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -232,9 +301,9 @@ status = "disabled"; }; - i2c@7000c700 { + i2c@0,7000c700 { compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c"; - reg = <0x7000c700 0x100>; + reg = <0x0 0x7000c700 0x0 0x100>; interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -247,9 +316,9 @@ status = "disabled"; }; - i2c@7000d000 { + i2c@0,7000d000 { compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c"; - reg = <0x7000d000 0x100>; + reg = <0x0 0x7000d000 0x0 0x100>; interrupts = <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -262,9 +331,9 @@ status = "disabled"; }; - i2c@7000d100 { + i2c@0,7000d100 { compatible = "nvidia,tegra124-i2c", "nvidia,tegra114-i2c"; - reg = <0x7000d100 0x100>; + reg = <0x0 0x7000d100 0x0 0x100>; interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -277,9 +346,9 @@ status = "disabled"; }; - spi@7000d400 { + spi@0,7000d400 { compatible = "nvidia,tegra124-spi", "nvidia,tegra114-spi"; - reg = <0x7000d400 0x200>; + reg = <0x0 0x7000d400 0x0 0x200>; interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -292,9 +361,9 @@ status = "disabled"; }; - spi@7000d600 { + spi@0,7000d600 { compatible = "nvidia,tegra124-spi", "nvidia,tegra114-spi"; - reg = <0x7000d600 0x200>; + reg = <0x0 0x7000d600 0x0 0x200>; interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -307,9 +376,9 @@ status = "disabled"; }; - spi@7000d800 { + spi@0,7000d800 { compatible = "nvidia,tegra124-spi", "nvidia,tegra114-spi"; - reg = <0x7000d800 0x200>; + reg = <0x0 0x7000d800 0x0 0x200>; interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -322,9 +391,9 @@ status = "disabled"; }; - spi@7000da00 { + spi@0,7000da00 { compatible = "nvidia,tegra124-spi", "nvidia,tegra114-spi"; - reg = <0x7000da00 0x200>; + reg = <0x0 0x7000da00 0x0 0x200>; interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -337,9 +406,9 @@ status = "disabled"; }; - spi@7000dc00 { + spi@0,7000dc00 { compatible = "nvidia,tegra124-spi", "nvidia,tegra114-spi"; - reg = <0x7000dc00 0x200>; + reg = <0x0 0x7000dc00 0x0 0x200>; interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -352,9 +421,9 @@ status = "disabled"; }; - spi@7000de00 { + spi@0,7000de00 { compatible = "nvidia,tegra124-spi", "nvidia,tegra114-spi"; - reg = <0x7000de00 0x200>; + reg = <0x0 0x7000de00 0x0 0x200>; interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; @@ -367,65 +436,65 @@ status = "disabled"; }; - rtc@7000e000 { + rtc@0,7000e000 { compatible = "nvidia,tegra124-rtc", "nvidia,tegra20-rtc"; - reg = <0x7000e000 0x100>; + reg = <0x0 0x7000e000 0x0 0x100>; interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA124_CLK_RTC>; }; - pmc@7000e400 { + pmc@0,7000e400 { compatible = "nvidia,tegra124-pmc"; - reg = <0x7000e400 0x400>; + reg = <0x0 0x7000e400 0x0 0x400>; clocks = <&tegra_car TEGRA124_CLK_PCLK>, <&clk32k_in>; clock-names = "pclk", "clk32k_in"; }; - sdhci@700b0000 { + sdhci@0,700b0000 { compatible = "nvidia,tegra124-sdhci"; - reg = <0x700b0000 0x200>; + reg = <0x0 0x700b0000 0x0 0x200>; interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA124_CLK_SDMMC1>; resets = <&tegra_car 14>; reset-names = "sdhci"; - status = "disable"; + status = "disabled"; }; - sdhci@700b0200 { + sdhci@0,700b0200 { compatible = "nvidia,tegra124-sdhci"; - reg = <0x700b0200 0x200>; + reg = <0x0 0x700b0200 0x0 0x200>; interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA124_CLK_SDMMC2>; resets = <&tegra_car 9>; reset-names = "sdhci"; - status = "disable"; + status = "disabled"; }; - sdhci@700b0400 { + sdhci@0,700b0400 { compatible = "nvidia,tegra124-sdhci"; - reg = <0x700b0400 0x200>; + reg = <0x0 0x700b0400 0x0 0x200>; interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA124_CLK_SDMMC3>; resets = <&tegra_car 69>; reset-names = "sdhci"; - status = "disable"; + status = "disabled"; }; - sdhci@700b0600 { + sdhci@0,700b0600 { compatible = "nvidia,tegra124-sdhci"; - reg = <0x700b0600 0x200>; + reg = <0x0 0x700b0600 0x0 0x200>; interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA124_CLK_SDMMC4>; resets = <&tegra_car 15>; reset-names = "sdhci"; - status = "disable"; + status = "disabled"; }; - ahub@70300000 { + ahub@0,70300000 { compatible = "nvidia,tegra124-ahub"; - reg = <0x70300000 0x200>, - <0x70300800 0x800>, - <0x70300200 0x600>; + reg = <0x0 0x70300000 0x0 0x200>, + <0x0 0x70300800 0x0 0x800>, + <0x0 0x70300200 0x0 0x600>; interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>; clocks = <&tegra_car TEGRA124_CLK_D_AUDIO>, <&tegra_car TEGRA124_CLK_APBIF>; @@ -470,12 +539,12 @@ "rx6", "tx6", "rx7", "tx7", "rx8", "tx8", "rx9", "tx9"; ranges; - #address-cells = <1>; - #size-cells = <1>; + #address-cells = <2>; + #size-cells = <2>; - tegra_i2s0: i2s@70301000 { + tegra_i2s0: i2s@0,70301000 { compatible = "nvidia,tegra124-i2s"; - reg = <0x70301000 0x100>; + reg = <0x0 0x70301000 0x0 0x100>; nvidia,ahub-cif-ids = <4 4>; clocks = <&tegra_car TEGRA124_CLK_I2S0>; resets = <&tegra_car 30>; @@ -483,9 +552,9 @@ status = "disabled"; }; - tegra_i2s1: i2s@70301100 { + tegra_i2s1: i2s@0,70301100 { compatible = "nvidia,tegra124-i2s"; - reg = <0x70301100 0x100>; + reg = <0x0 0x70301100 0x0 0x100>; nvidia,ahub-cif-ids = <5 5>; clocks = <&tegra_car TEGRA124_CLK_I2S1>; resets = <&tegra_car 11>; @@ -493,9 +562,9 @@ status = "disabled"; }; - tegra_i2s2: i2s@70301200 { + tegra_i2s2: i2s@0,70301200 { compatible = "nvidia,tegra124-i2s"; - reg = <0x70301200 0x100>; + reg = <0x0 0x70301200 0x0 0x100>; nvidia,ahub-cif-ids = <6 6>; clocks = <&tegra_car TEGRA124_CLK_I2S2>; resets = <&tegra_car 18>; @@ -503,9 +572,9 @@ status = "disabled"; }; - tegra_i2s3: i2s@70301300 { + tegra_i2s3: i2s@0,70301300 { compatible = "nvidia,tegra124-i2s"; - reg = <0x70301300 0x100>; + reg = <0x0 0x70301300 0x0 0x100>; nvidia,ahub-cif-ids = <7 7>; clocks = <&tegra_car TEGRA124_CLK_I2S3>; resets = <&tegra_car 101>; @@ -513,9 +582,9 @@ status = "disabled"; }; - tegra_i2s4: i2s@70301400 { + tegra_i2s4: i2s@0,70301400 { compatible = "nvidia,tegra124-i2s"; - reg = <0x70301400 0x100>; + reg = <0x0 0x70301400 0x0 0x100>; nvidia,ahub-cif-ids = <8 8>; clocks = <&tegra_car TEGRA124_CLK_I2S4>; resets = <&tegra_car 102>; @@ -524,6 +593,108 @@ }; }; + usb@0,7d000000 { + compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci"; + reg = <0x0 0x7d000000 0x0 0x4000>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USBD>; + resets = <&tegra_car 22>; + reset-names = "usb"; + nvidia,phy = <&phy1>; + status = "disabled"; + }; + + phy1: usb-phy@0,7d000000 { + compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy"; + reg = <0x0 0x7d000000 0x0 0x4000>, + <0x0 0x7d000000 0x0 0x4000>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USBD>, + <&tegra_car TEGRA124_CLK_PLL_U>, + <&tegra_car TEGRA124_CLK_USBD>; + clock-names = "reg", "pll_u", "utmi-pads"; + nvidia,hssync-start-delay = <0>; + nvidia,idle-wait-delay = <17>; + nvidia,elastic-limit = <16>; + nvidia,term-range-adj = <6>; + nvidia,xcvr-setup = <9>; + nvidia,xcvr-lsfslew = <0>; + nvidia,xcvr-lsrslew = <3>; + nvidia,hssquelch-level = <2>; + nvidia,hsdiscon-level = <5>; + nvidia,xcvr-hsslew = <12>; + status = "disabled"; + }; + + usb@0,7d004000 { + compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci"; + reg = <0x0 0x7d004000 0x0 0x4000>; + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USB2>; + resets = <&tegra_car 58>; + reset-names = "usb"; + nvidia,phy = <&phy2>; + status = "disabled"; + }; + + phy2: usb-phy@0,7d004000 { + compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy"; + reg = <0x0 0x7d004000 0x0 0x4000>, + <0x0 0x7d000000 0x0 0x4000>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USB2>, + <&tegra_car TEGRA124_CLK_PLL_U>, + <&tegra_car TEGRA124_CLK_USBD>; + clock-names = "reg", "pll_u", "utmi-pads"; + nvidia,hssync-start-delay = <0>; + nvidia,idle-wait-delay = <17>; + nvidia,elastic-limit = <16>; + nvidia,term-range-adj = <6>; + nvidia,xcvr-setup = <9>; + nvidia,xcvr-lsfslew = <0>; + nvidia,xcvr-lsrslew = <3>; + nvidia,hssquelch-level = <2>; + nvidia,hsdiscon-level = <5>; + nvidia,xcvr-hsslew = <12>; + status = "disabled"; + }; + + usb@0,7d008000 { + compatible = "nvidia,tegra124-ehci", "nvidia,tegra30-ehci", "usb-ehci"; + reg = <0x0 0x7d008000 0x0 0x4000>; + interrupts = <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USB3>; + resets = <&tegra_car 59>; + reset-names = "usb"; + nvidia,phy = <&phy3>; + status = "disabled"; + }; + + phy3: usb-phy@0,7d008000 { + compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy"; + reg = <0x0 0x7d008000 0x0 0x4000>, + <0x0 0x7d000000 0x0 0x4000>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USB3>, + <&tegra_car TEGRA124_CLK_PLL_U>, + <&tegra_car TEGRA124_CLK_USBD>; + clock-names = "reg", "pll_u", "utmi-pads"; + nvidia,hssync-start-delay = <0>; + nvidia,idle-wait-delay = <17>; + nvidia,elastic-limit = <16>; + nvidia,term-range-adj = <6>; + nvidia,xcvr-setup = <9>; + nvidia,xcvr-lsfslew = <0>; + nvidia,xcvr-lsrslew = <3>; + nvidia,hssquelch-level = <2>; + nvidia,hsdiscon-level = <5>; + nvidia,xcvr-hsslew = <12>; + status = "disabled"; + }; + cpus { #address-cells = <1>; #size-cells = <0>; diff --git a/arch/arm/boot/dts/tegra20-paz00.dts b/arch/arm/boot/dts/tegra20-paz00.dts index c7cd8e6802d7..9a39a8001f78 100644 --- a/arch/arm/boot/dts/tegra20-paz00.dts +++ b/arch/arm/boot/dts/tegra20-paz00.dts @@ -17,6 +17,14 @@ }; host1x@50000000 { + dc@54200000 { + rgb { + status = "okay"; + + nvidia,panel = <&panel>; + }; + }; + hdmi@54280000 { status = "okay"; @@ -257,7 +265,11 @@ status = "okay"; }; - i2c@7000c000 { + pwm: pwm@7000a000 { + status = "okay"; + }; + + lvds_ddc: i2c@7000c000 { status = "okay"; clock-frequency = <400000>; @@ -475,6 +487,18 @@ non-removable; }; + backlight: backlight { + compatible = "pwm-backlight"; + + enable-gpios = <&gpio TEGRA_GPIO(U, 4) GPIO_ACTIVE_HIGH>; + pwms = <&pwm 0 5000000>; + + brightness-levels = <0 16 32 48 64 80 96 112 128 144 160 176 192 208 224 240 255>; + default-brightness-level = <10>; + + backlight-boot-off; + }; + clocks { compatible = "simple-bus"; #address-cells = <1>; @@ -509,6 +533,16 @@ }; }; + panel: panel { + compatible = "samsung,ltn101nt05", "simple-panel"; + + ddc-i2c-bus = <&lvds_ddc>; + power-supply = <&vdd_pnl_reg>; + enable-gpios = <&gpio TEGRA_GPIO(M, 6) GPIO_ACTIVE_HIGH>; + + backlight = <&backlight>; + }; + regulators { compatible = "simple-bus"; #address-cells = <1>; @@ -522,6 +556,16 @@ regulator-max-microvolt = <5000000>; regulator-always-on; }; + + vdd_pnl_reg: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "+3VS,vdd_pnl"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio TEGRA_GPIO(A, 4) GPIO_ACTIVE_HIGH>; + enable-active-high; + }; }; sound { diff --git a/arch/arm/boot/dts/tegra20-seaboard.dts b/arch/arm/boot/dts/tegra20-seaboard.dts index a11b6e7b4759..a1d4bf9895d7 100644 --- a/arch/arm/boot/dts/tegra20-seaboard.dts +++ b/arch/arm/boot/dts/tegra20-seaboard.dts @@ -17,6 +17,14 @@ }; host1x@50000000 { + dc@54200000 { + rgb { + status = "okay"; + + nvidia,panel = <&panel>; + }; + }; + hdmi@54280000 { status = "okay"; @@ -312,6 +320,10 @@ status = "okay"; }; + pwm: pwm@7000a000 { + status = "okay"; + }; + i2c@7000c000 { status = "okay"; clock-frequency = <400000>; @@ -369,7 +381,7 @@ #size-cells = <0>; }; - i2c@1 { + lvds_ddc: i2c@1 { reg = <1>; #address-cells = <1>; #size-cells = <0>; @@ -762,6 +774,17 @@ non-removable; }; + backlight: backlight { + compatible = "pwm-backlight"; + + enable-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_HIGH>; + power-supply = <&vdd_bl_reg>; + pwms = <&pwm 2 5000000>; + + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + }; + clocks { compatible = "simple-bus"; #address-cells = <1>; @@ -795,6 +818,16 @@ }; }; + panel: panel { + compatible = "chunghwa,claa101wa01a", "simple-panel"; + + power-supply = <&vdd_pnl_reg>; + enable-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_HIGH>; + + backlight = <&backlight>; + ddc-i2c-bus = <&lvds_ddc>; + }; + regulators { compatible = "simple-bus"; #address-cells = <1>; @@ -839,6 +872,26 @@ regulator-always-on; regulator-boot-on; }; + + vdd_pnl_reg: regulator@4 { + compatible = "regulator-fixed"; + reg = <4>; + regulator-name = "vdd_pnl"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&gpio TEGRA_GPIO(C, 6) GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + vdd_bl_reg: regulator@5 { + compatible = "regulator-fixed"; + reg = <5>; + regulator-name = "vdd_bl"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + gpio = <&gpio TEGRA_GPIO(W, 0) GPIO_ACTIVE_HIGH>; + enable-active-high; + }; }; sound { diff --git a/arch/arm/boot/dts/tegra20-ventana.dts b/arch/arm/boot/dts/tegra20-ventana.dts index 571d12e6ac2d..ca8484cccddc 100644 --- a/arch/arm/boot/dts/tegra20-ventana.dts +++ b/arch/arm/boot/dts/tegra20-ventana.dts @@ -17,6 +17,14 @@ }; host1x@50000000 { + dc@54200000 { + rgb { + status = "okay"; + + nvidia,panel = <&panel>; + }; + }; + hdmi@54280000 { status = "okay"; @@ -309,6 +317,10 @@ status = "okay"; }; + pwm: pwm@7000a000 { + status = "okay"; + }; + i2c@7000c000 { status = "okay"; clock-frequency = <400000>; @@ -359,7 +371,7 @@ #size-cells = <0>; }; - i2c@1 { + lvds_ddc: i2c@1 { reg = <1>; #address-cells = <1>; #size-cells = <0>; @@ -557,6 +569,17 @@ non-removable; }; + backlight: backlight { + compatible = "pwm-backlight"; + + enable-gpios = <&gpio TEGRA_GPIO(D, 4) GPIO_ACTIVE_HIGH>; + power-supply = <&vdd_bl_reg>; + pwms = <&pwm 2 5000000>; + + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + }; + clocks { compatible = "simple-bus"; #address-cells = <1>; @@ -581,6 +604,16 @@ }; }; + panel: panel { + compatible = "chunghwa,claa101wa01a", "simple-panel"; + + power-supply = <&vdd_pnl_reg>; + enable-gpios = <&gpio TEGRA_GPIO(B, 2) GPIO_ACTIVE_HIGH>; + + backlight = <&backlight>; + ddc-i2c-bus = <&lvds_ddc>; + }; + regulators { compatible = "simple-bus"; #address-cells = <1>; @@ -614,7 +647,7 @@ enable-active-high; }; - regulator@3 { + vdd_pnl_reg: regulator@3 { compatible = "regulator-fixed"; reg = <3>; regulator-name = "vdd_pnl"; @@ -624,7 +657,7 @@ enable-active-high; }; - regulator@4 { + vdd_bl_reg: regulator@4 { compatible = "regulator-fixed"; reg = <4>; regulator-name = "vdd_bl"; diff --git a/arch/arm/boot/dts/tegra20.dtsi b/arch/arm/boot/dts/tegra20.dtsi index 48d2a7f4d0c0..a7ddf70df50b 100644 --- a/arch/arm/boot/dts/tegra20.dtsi +++ b/arch/arm/boot/dts/tegra20.dtsi @@ -556,6 +556,10 @@ GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ interrupt-names = "intr", "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + bus-range = <0x00 0xff>; #address-cells = <3>; #size-cells = <2>; diff --git a/arch/arm/boot/dts/tegra30-cardhu.dtsi b/arch/arm/boot/dts/tegra30-cardhu.dtsi index 1e156d9d0506..0cf0848a82d8 100644 --- a/arch/arm/boot/dts/tegra30-cardhu.dtsi +++ b/arch/arm/boot/dts/tegra30-cardhu.dtsi @@ -187,6 +187,13 @@ interrupt-parent = <&gpio>; interrupts = <TEGRA_GPIO(L, 0) IRQ_TYPE_LEVEL_HIGH>; }; + + i2cmux@70 { + compatible = "nxp,pca9546"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x70>; + }; }; i2c@7000c700 { diff --git a/arch/arm/boot/dts/tegra30.dtsi b/arch/arm/boot/dts/tegra30.dtsi index 19a84e933f4e..dec4fc823901 100644 --- a/arch/arm/boot/dts/tegra30.dtsi +++ b/arch/arm/boot/dts/tegra30.dtsi @@ -28,6 +28,10 @@ GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ interrupt-names = "intr", "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + bus-range = <0x00 0xff>; #address-cells = <3>; #size-cells = <2>; @@ -144,9 +148,9 @@ compatible = "nvidia,tegra30-gr2d"; reg = <0x54140000 0x00040000>; interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&tegra_car TEGRA30_CLK_GR2D>; resets = <&tegra_car 21>; reset-names = "2d"; - clocks = <&tegra_car TEGRA30_CLK_GR2D>; }; gr3d@54180000 { diff --git a/arch/arm/boot/dts/tps65910.dtsi b/arch/arm/boot/dts/tps65910.dtsi index 92693a89160e..b0ac6657a170 100644 --- a/arch/arm/boot/dts/tps65910.dtsi +++ b/arch/arm/boot/dts/tps65910.dtsi @@ -82,5 +82,10 @@ reg = <12>; regulator-compatible = "vmmc"; }; + + vbb_reg: regulator@13 { + reg = <13>; + regulator-compatible = "vbb"; + }; }; }; diff --git a/arch/arm/boot/dts/twl4030.dtsi b/arch/arm/boot/dts/twl4030.dtsi index 4217096ee677..86cfc7d15ca7 100644 --- a/arch/arm/boot/dts/twl4030.dtsi +++ b/arch/arm/boot/dts/twl4030.dtsi @@ -145,4 +145,11 @@ compatible = "ti,twl4030-pwrbutton"; interrupts = <8>; }; + + twl_keypad: keypad { + compatible = "ti,twl4030-keypad"; + interrupts = <1>; + keypad,num-rows = <8>; + keypad,num-columns = <8>; + }; }; diff --git a/arch/arm/boot/dts/vf610-cosmic.dts b/arch/arm/boot/dts/vf610-cosmic.dts index c42e4f938dcd..3fd1b74e1216 100644 --- a/arch/arm/boot/dts/vf610-cosmic.dts +++ b/arch/arm/boot/dts/vf610-cosmic.dts @@ -36,12 +36,37 @@ &fec1 { phy-mode = "rmii"; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec1_1>; + pinctrl-0 = <&pinctrl_fec1>; status = "okay"; }; +&iomuxc { + vf610-cosmic { + pinctrl_fec1: fec1grp { + fsl,pins = < + VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2 + VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3 + VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1 + VF610_PAD_PTC12__ENET_RMII_RXD1 0x30d1 + VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1 + VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1 + VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2 + VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2 + VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + VF610_PAD_PTB4__UART1_TX 0x21a2 + VF610_PAD_PTB5__UART1_RX 0x21a1 + >; + }; + }; +}; + &uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_1>; + pinctrl-0 = <&pinctrl_uart1>; status = "okay"; }; diff --git a/arch/arm/boot/dts/vf610-twr.dts b/arch/arm/boot/dts/vf610-twr.dts index c8047ca16501..7dd1d6ede525 100644 --- a/arch/arm/boot/dts/vf610-twr.dts +++ b/arch/arm/boot/dts/vf610-twr.dts @@ -34,12 +34,70 @@ }; }; + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_3p3v: regulator@0 { + compatible = "regulator-fixed"; + reg = <0>; + regulator-name = "3P3V"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_vcc_3v3_mcu: regulator@1 { + compatible = "regulator-fixed"; + reg = <1>; + regulator-name = "vcc_3v3_mcu"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + }; + + sound { + compatible = "simple-audio-card"; + simple-audio-card,format = "i2s"; + simple-audio-card,widgets = + "Microphone", "Microphone Jack", + "Headphone", "Headphone Jack", + "Speaker", "Speaker Ext", + "Line", "Line In Jack"; + simple-audio-card,routing = + "MIC_IN", "Microphone Jack", + "Microphone Jack", "Mic Bias", + "LINE_IN", "Line In Jack", + "Headphone Jack", "HP_OUT", + "Speaker Ext", "LINE_OUT"; + + simple-audio-card,cpu { + sound-dai = <&sai2>; + master-clkdir-out; + frame-master; + bitclock-master; + }; + + simple-audio-card,codec { + sound-dai = <&codec>; + frame-master; + bitclock-master; + }; + }; +}; + +&adc0 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_adc0_ad5>; + vref-supply = <®_vcc_3v3_mcu>; + status = "okay"; }; &dspi0 { bus-num = <0>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_dspi0_1>; + pinctrl-0 = <&pinctrl_dspi0>; status = "okay"; sflash: at26df081a@0 { @@ -56,26 +114,116 @@ &fec0 { phy-mode = "rmii"; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec0_1>; + pinctrl-0 = <&pinctrl_fec0>; status = "okay"; }; &fec1 { phy-mode = "rmii"; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_fec1_1>; + pinctrl-0 = <&pinctrl_fec1>; status = "okay"; }; &i2c0 { clock-frequency = <100000>; pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_i2c0_1>; + pinctrl-0 = <&pinctrl_i2c0>; + status = "okay"; + + codec: sgtl5000@0a { + #sound-dai-cells = <0>; + compatible = "fsl,sgtl5000"; + reg = <0x0a>; + VDDA-supply = <®_3p3v>; + VDDIO-supply = <®_3p3v>; + clocks = <&clks VF610_CLK_SAI2>; + }; +}; + +&iomuxc { + vf610-twr { + pinctrl_adc0_ad5: adc0ad5grp { + fsl,pins = < + VF610_PAD_PTC30__ADC0_SE5 0xa1 + >; + }; + + pinctrl_dspi0: dspi0grp { + fsl,pins = < + VF610_PAD_PTB19__DSPI0_CS0 0x1182 + VF610_PAD_PTB20__DSPI0_SIN 0x1181 + VF610_PAD_PTB21__DSPI0_SOUT 0x1182 + VF610_PAD_PTB22__DSPI0_SCK 0x1182 + >; + }; + + pinctrl_fec0: fec0grp { + fsl,pins = < + VF610_PAD_PTA6__RMII_CLKIN 0x30d1 + VF610_PAD_PTC0__ENET_RMII0_MDC 0x30d3 + VF610_PAD_PTC1__ENET_RMII0_MDIO 0x30d1 + VF610_PAD_PTC2__ENET_RMII0_CRS 0x30d1 + VF610_PAD_PTC3__ENET_RMII0_RXD1 0x30d1 + VF610_PAD_PTC4__ENET_RMII0_RXD0 0x30d1 + VF610_PAD_PTC5__ENET_RMII0_RXER 0x30d1 + VF610_PAD_PTC6__ENET_RMII0_TXD1 0x30d2 + VF610_PAD_PTC7__ENET_RMII0_TXD0 0x30d2 + VF610_PAD_PTC8__ENET_RMII0_TXEN 0x30d2 + >; + }; + + pinctrl_fec1: fec1grp { + fsl,pins = < + VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2 + VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3 + VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1 + VF610_PAD_PTC12__ENET_RMII_RXD1 0x30d1 + VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1 + VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1 + VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2 + VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2 + VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2 + >; + }; + + pinctrl_i2c0: i2c0grp { + fsl,pins = < + VF610_PAD_PTB14__I2C0_SCL 0x30d3 + VF610_PAD_PTB15__I2C0_SDA 0x30d3 + >; + }; + + pinctrl_sai2: sai2grp { + fsl,pins = < + VF610_PAD_PTA16__SAI2_TX_BCLK 0x02ed + VF610_PAD_PTA18__SAI2_TX_DATA 0x02ee + VF610_PAD_PTA19__SAI2_TX_SYNC 0x02ed + VF610_PAD_PTA21__SAI2_RX_BCLK 0x02ed + VF610_PAD_PTA22__SAI2_RX_DATA 0x02ed + VF610_PAD_PTA23__SAI2_RX_SYNC 0x02ed + VF610_PAD_PTB18__EXT_AUDIO_MCLK 0x02ed + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + VF610_PAD_PTB4__UART1_TX 0x21a2 + VF610_PAD_PTB5__UART1_RX 0x21a1 + >; + }; + }; +}; + +&sai2 { + #sound-dai-cells = <0>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sai2>; status = "okay"; }; &uart1 { pinctrl-names = "default"; - pinctrl-0 = <&pinctrl_uart1_1>; + pinctrl-0 = <&pinctrl_uart1>; status = "okay"; }; diff --git a/arch/arm/boot/dts/vf610.dtsi b/arch/arm/boot/dts/vf610.dtsi index d31ce1b4a7b0..804873367669 100644 --- a/arch/arm/boot/dts/vf610.dtsi +++ b/arch/arm/boot/dts/vf610.dtsi @@ -10,6 +10,7 @@ #include "skeleton.dtsi" #include "vf610-pinfunc.h" #include <dt-bindings/clock/vf610-clock.h> +#include <dt-bindings/interrupt-controller/irq.h> / { aliases { @@ -87,39 +88,66 @@ arm,tag-latency = <2 2 2>; }; + edma0: dma-controller@40018000 { + #dma-cells = <2>; + compatible = "fsl,vf610-edma"; + reg = <0x40018000 0x2000>, + <0x40024000 0x1000>, + <0x40025000 0x1000>; + interrupts = <0 8 IRQ_TYPE_LEVEL_HIGH>, + <0 9 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "edma-tx", "edma-err"; + dma-channels = <32>; + clock-names = "dmamux0", "dmamux1"; + clocks = <&clks VF610_CLK_DMAMUX0>, + <&clks VF610_CLK_DMAMUX1>; + }; + uart0: serial@40027000 { compatible = "fsl,vf610-lpuart"; reg = <0x40027000 0x1000>; - interrupts = <0 61 0x00>; + interrupts = <0 61 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_UART0>; clock-names = "ipg"; + dmas = <&edma0 0 2>, + <&edma0 0 3>; + dma-names = "rx","tx"; status = "disabled"; }; uart1: serial@40028000 { compatible = "fsl,vf610-lpuart"; reg = <0x40028000 0x1000>; - interrupts = <0 62 0x04>; + interrupts = <0 62 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_UART1>; clock-names = "ipg"; + dmas = <&edma0 0 4>, + <&edma0 0 5>; + dma-names = "rx","tx"; status = "disabled"; }; uart2: serial@40029000 { compatible = "fsl,vf610-lpuart"; reg = <0x40029000 0x1000>; - interrupts = <0 63 0x04>; + interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_UART2>; clock-names = "ipg"; + dmas = <&edma0 0 6>, + <&edma0 0 7>; + dma-names = "rx","tx"; status = "disabled"; }; uart3: serial@4002a000 { compatible = "fsl,vf610-lpuart"; reg = <0x4002a000 0x1000>; - interrupts = <0 64 0x04>; + interrupts = <0 64 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_UART3>; clock-names = "ipg"; + dmas = <&edma0 0 8>, + <&edma0 0 9>; + dma-names = "rx","tx"; status = "disabled"; }; @@ -128,7 +156,7 @@ #size-cells = <0>; compatible = "fsl,vf610-dspi"; reg = <0x4002c000 0x1000>; - interrupts = <0 67 0x04>; + interrupts = <0 67 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_DSPI0>; clock-names = "dspi"; spi-num-chipselects = <5>; @@ -138,20 +166,32 @@ sai2: sai@40031000 { compatible = "fsl,vf610-sai"; reg = <0x40031000 0x1000>; - interrupts = <0 86 0x04>; + interrupts = <0 86 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_SAI2>; clock-names = "sai"; + dma-names = "tx", "rx"; + dmas = <&edma0 0 21>, + <&edma0 0 20>; status = "disabled"; }; pit: pit@40037000 { compatible = "fsl,vf610-pit"; reg = <0x40037000 0x1000>; - interrupts = <0 39 0x04>; + interrupts = <0 39 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_PIT>; clock-names = "pit"; }; + adc0: adc@4003b000 { + compatible = "fsl,vf610-adc"; + reg = <0x4003b000 0x1000>; + interrupts = <0 53 0x04>; + clocks = <&clks VF610_CLK_ADC0>; + clock-names = "adc"; + status = "disabled"; + }; + wdog@4003e000 { compatible = "fsl,vf610-wdt", "fsl,imx21-wdt"; reg = <0x4003e000 0x1000>; @@ -164,7 +204,7 @@ #size-cells = <0>; compatible = "fsl,vf610-qspi"; reg = <0x40044000 0x1000>; - interrupts = <0 24 0x04>; + interrupts = <0 24 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_QSPI0_EN>, <&clks VF610_CLK_QSPI0>; clock-names = "qspi_en", "qspi"; @@ -175,182 +215,12 @@ compatible = "fsl,vf610-iomuxc"; reg = <0x40048000 0x1000>; #gpio-range-cells = <3>; - - /* functions and groups pins */ - - dcu0 { - pinctrl_dcu0_1: dcu0grp_1 { - fsl,pins = < - VF610_PAD_PTB8__GPIO_30 0x42 - VF610_PAD_PTE0__DCU0_HSYNC 0x42 - VF610_PAD_PTE1__DCU0_VSYNC 0x42 - VF610_PAD_PTE2__DCU0_PCLK 0x42 - VF610_PAD_PTE4__DCU0_DE 0x42 - VF610_PAD_PTE5__DCU0_R0 0x42 - VF610_PAD_PTE6__DCU0_R1 0x42 - VF610_PAD_PTE7__DCU0_R2 0x42 - VF610_PAD_PTE8__DCU0_R3 0x42 - VF610_PAD_PTE9__DCU0_R4 0x42 - VF610_PAD_PTE10__DCU0_R5 0x42 - VF610_PAD_PTE11__DCU0_R6 0x42 - VF610_PAD_PTE12__DCU0_R7 0x42 - VF610_PAD_PTE13__DCU0_G0 0x42 - VF610_PAD_PTE14__DCU0_G1 0x42 - VF610_PAD_PTE15__DCU0_G2 0x42 - VF610_PAD_PTE16__DCU0_G3 0x42 - VF610_PAD_PTE17__DCU0_G4 0x42 - VF610_PAD_PTE18__DCU0_G5 0x42 - VF610_PAD_PTE19__DCU0_G6 0x42 - VF610_PAD_PTE20__DCU0_G7 0x42 - VF610_PAD_PTE21__DCU0_B0 0x42 - VF610_PAD_PTE22__DCU0_B1 0x42 - VF610_PAD_PTE23__DCU0_B2 0x42 - VF610_PAD_PTE24__DCU0_B3 0x42 - VF610_PAD_PTE25__DCU0_B4 0x42 - VF610_PAD_PTE26__DCU0_B5 0x42 - VF610_PAD_PTE27__DCU0_B6 0x42 - VF610_PAD_PTE28__DCU0_B7 0x42 - >; - }; - }; - - dspi0 { - pinctrl_dspi0_1: dspi0grp_1 { - fsl,pins = < - VF610_PAD_PTB19__DSPI0_CS0 0x1182 - VF610_PAD_PTB20__DSPI0_SIN 0x1181 - VF610_PAD_PTB21__DSPI0_SOUT 0x1182 - VF610_PAD_PTB22__DSPI0_SCK 0x1182 - >; - }; - }; - - esdhc1 { - pinctrl_esdhc1_1: esdhc1grp_1 { - fsl,pins = < - VF610_PAD_PTA24__ESDHC1_CLK 0x31ef - VF610_PAD_PTA25__ESDHC1_CMD 0x31ef - VF610_PAD_PTA26__ESDHC1_DAT0 0x31ef - VF610_PAD_PTA27__ESDHC1_DAT1 0x31ef - VF610_PAD_PTA28__ESDHC1_DATA2 0x31ef - VF610_PAD_PTA29__ESDHC1_DAT3 0x31ef - VF610_PAD_PTA7__GPIO_134 0x219d - >; - }; - }; - - fec0 { - pinctrl_fec0_1: fec0grp_1 { - fsl,pins = < - VF610_PAD_PTA6__RMII_CLKIN 0x30d1 - VF610_PAD_PTC0__ENET_RMII0_MDC 0x30d3 - VF610_PAD_PTC1__ENET_RMII0_MDIO 0x30d1 - VF610_PAD_PTC2__ENET_RMII0_CRS 0x30d1 - VF610_PAD_PTC3__ENET_RMII0_RXD1 0x30d1 - VF610_PAD_PTC4__ENET_RMII0_RXD0 0x30d1 - VF610_PAD_PTC5__ENET_RMII0_RXER 0x30d1 - VF610_PAD_PTC6__ENET_RMII0_TXD1 0x30d2 - VF610_PAD_PTC7__ENET_RMII0_TXD0 0x30d2 - VF610_PAD_PTC8__ENET_RMII0_TXEN 0x30d2 - >; - }; - }; - - fec1 { - pinctrl_fec1_1: fec1grp_1 { - fsl,pins = < - VF610_PAD_PTC9__ENET_RMII1_MDC 0x30d2 - VF610_PAD_PTC10__ENET_RMII1_MDIO 0x30d3 - VF610_PAD_PTC11__ENET_RMII1_CRS 0x30d1 - VF610_PAD_PTC12__ENET_RMII_RXD1 0x30d1 - VF610_PAD_PTC13__ENET_RMII1_RXD0 0x30d1 - VF610_PAD_PTC14__ENET_RMII1_RXER 0x30d1 - VF610_PAD_PTC15__ENET_RMII1_TXD1 0x30d2 - VF610_PAD_PTC16__ENET_RMII1_TXD0 0x30d2 - VF610_PAD_PTC17__ENET_RMII1_TXEN 0x30d2 - >; - }; - }; - - i2c0 { - pinctrl_i2c0_1: i2c0grp_1 { - fsl,pins = < - VF610_PAD_PTB14__I2C0_SCL 0x30d3 - VF610_PAD_PTB15__I2C0_SDA 0x30d3 - >; - }; - }; - - pwm0 { - pinctrl_pwm0_1: pwm0grp_1 { - fsl,pins = < - VF610_PAD_PTB0__FTM0_CH0 0x1582 - VF610_PAD_PTB1__FTM0_CH1 0x1582 - VF610_PAD_PTB2__FTM0_CH2 0x1582 - VF610_PAD_PTB3__FTM0_CH3 0x1582 - VF610_PAD_PTB6__FTM0_CH6 0x1582 - VF610_PAD_PTB7__FTM0_CH7 0x1582 - >; - }; - }; - - qspi0 { - pinctrl_qspi0_1: qspi0grp_1 { - fsl,pins = < - VF610_PAD_PTD0__QSPI0_A_QSCK 0x307b - VF610_PAD_PTD1__QSPI0_A_CS0 0x307f - VF610_PAD_PTD2__QSPI0_A_DATA3 0x3073 - VF610_PAD_PTD3__QSPI0_A_DATA2 0x3073 - VF610_PAD_PTD4__QSPI0_A_DATA1 0x3073 - VF610_PAD_PTD5__QSPI0_A_DATA0 0x307b - VF610_PAD_PTD7__QSPI0_B_QSCK 0x307b - VF610_PAD_PTD8__QSPI0_B_CS0 0x307f - VF610_PAD_PTD9__QSPI0_B_DATA3 0x3073 - VF610_PAD_PTD10__QSPI0_B_DATA2 0x3073 - VF610_PAD_PTD11__QSPI0_B_DATA1 0x3073 - VF610_PAD_PTD12__QSPI0_B_DATA0 0x307b - >; - }; - }; - - sai2 { - pinctrl_sai2_1: sai2grp_1 { - fsl,pins = < - VF610_PAD_PTA16__SAI2_TX_BCLK 0x02ed - VF610_PAD_PTA18__SAI2_TX_DATA 0x02ee - VF610_PAD_PTA19__SAI2_TX_SYNC 0x02ed - VF610_PAD_PTA21__SAI2_RX_BCLK 0x02ed - VF610_PAD_PTA22__SAI2_RX_DATA 0x02ed - VF610_PAD_PTA23__SAI2_RX_SYNC 0x02ed - VF610_PAD_PTB18__EXT_AUDIO_MCLK 0x02ed - >; - }; - }; - - uart1 { - pinctrl_uart1_1: uart1grp_1 { - fsl,pins = < - VF610_PAD_PTB4__UART1_TX 0x21a2 - VF610_PAD_PTB5__UART1_RX 0x21a1 - >; - }; - }; - - usbvbus { - pinctrl_usbvbus_1: usbvbusgrp_1 { - fsl,pins = < - VF610_PAD_PTA24__USB1_VBUS_EN 0x219c - VF610_PAD_PTA16__USB0_VBUS_EN 0x219c - >; - }; - }; - }; gpio1: gpio@40049000 { compatible = "fsl,vf610-gpio"; reg = <0x40049000 0x1000 0x400ff000 0x40>; - interrupts = <0 107 0x04>; + interrupts = <0 107 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -361,7 +231,7 @@ gpio2: gpio@4004a000 { compatible = "fsl,vf610-gpio"; reg = <0x4004a000 0x1000 0x400ff040 0x40>; - interrupts = <0 108 0x04>; + interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -372,7 +242,7 @@ gpio3: gpio@4004b000 { compatible = "fsl,vf610-gpio"; reg = <0x4004b000 0x1000 0x400ff080 0x40>; - interrupts = <0 109 0x04>; + interrupts = <0 109 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -383,7 +253,7 @@ gpio4: gpio@4004c000 { compatible = "fsl,vf610-gpio"; reg = <0x4004c000 0x1000 0x400ff0c0 0x40>; - interrupts = <0 110 0x04>; + interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -394,7 +264,7 @@ gpio5: gpio@4004d000 { compatible = "fsl,vf610-gpio"; reg = <0x4004d000 0x1000 0x400ff100 0x40>; - interrupts = <0 111 0x04>; + interrupts = <0 111 IRQ_TYPE_LEVEL_HIGH>; gpio-controller; #gpio-cells = <2>; interrupt-controller; @@ -412,9 +282,12 @@ #size-cells = <0>; compatible = "fsl,vf610-i2c"; reg = <0x40066000 0x1000>; - interrupts =<0 71 0x04>; + interrupts =<0 71 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_I2C0>; clock-names = "ipg"; + dmas = <&edma0 0 50>, + <&edma0 0 51>; + dma-names = "rx","tx"; status = "disabled"; }; @@ -432,10 +305,25 @@ reg = <0x40080000 0x80000>; ranges; + edma1: dma-controller@40098000 { + #dma-cells = <2>; + compatible = "fsl,vf610-edma"; + reg = <0x40098000 0x2000>, + <0x400a1000 0x1000>, + <0x400a2000 0x1000>; + interrupts = <0 10 IRQ_TYPE_LEVEL_HIGH>, + <0 11 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "edma-tx", "edma-err"; + dma-channels = <32>; + clock-names = "dmamux0", "dmamux1"; + clocks = <&clks VF610_CLK_DMAMUX2>, + <&clks VF610_CLK_DMAMUX3>; + }; + uart4: serial@400a9000 { compatible = "fsl,vf610-lpuart"; reg = <0x400a9000 0x1000>; - interrupts = <0 65 0x04>; + interrupts = <0 65 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_UART4>; clock-names = "ipg"; status = "disabled"; @@ -444,16 +332,25 @@ uart5: serial@400aa000 { compatible = "fsl,vf610-lpuart"; reg = <0x400aa000 0x1000>; - interrupts = <0 66 0x04>; + interrupts = <0 66 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_UART5>; clock-names = "ipg"; status = "disabled"; }; + adc1: adc@400bb000 { + compatible = "fsl,vf610-adc"; + reg = <0x400bb000 0x1000>; + interrupts = <0 54 0x04>; + clocks = <&clks VF610_CLK_ADC1>; + clock-names = "adc"; + status = "disabled"; + }; + fec0: ethernet@400d0000 { compatible = "fsl,mvf600-fec"; reg = <0x400d0000 0x1000>; - interrupts = <0 78 0x04>; + interrupts = <0 78 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_ENET0>, <&clks VF610_CLK_ENET0>, <&clks VF610_CLK_ENET>; @@ -464,7 +361,7 @@ fec1: ethernet@400d1000 { compatible = "fsl,mvf600-fec"; reg = <0x400d1000 0x1000>; - interrupts = <0 79 0x04>; + interrupts = <0 79 IRQ_TYPE_LEVEL_HIGH>; clocks = <&clks VF610_CLK_ENET1>, <&clks VF610_CLK_ENET1>, <&clks VF610_CLK_ENET>; diff --git a/arch/arm/boot/dts/zynq-7000.dtsi b/arch/arm/boot/dts/zynq-7000.dtsi index 789d0bacc110..286a840e3dce 100644 --- a/arch/arm/boot/dts/zynq-7000.dtsi +++ b/arch/arm/boot/dts/zynq-7000.dtsi @@ -140,6 +140,7 @@ #clock-cells = <1>; compatible = "xlnx,ps7-clkc"; ps-clk-frequency = <33333333>; + fclk-enable = <0>; clock-output-names = "armpll", "ddrpll", "iopll", "cpu_6or4x", "cpu_3or2x", "cpu_2x", "cpu_1x", "ddr2x", "ddr3x", "dci", "lqspi", "smc", "pcap", "gem0", "gem1", diff --git a/arch/arm/mach-keystone/keystone.c b/arch/arm/mach-keystone/keystone.c index 6e6bb7d5ea30..e0b9e1b9cf30 100644 --- a/arch/arm/mach-keystone/keystone.c +++ b/arch/arm/mach-keystone/keystone.c @@ -46,7 +46,7 @@ static void __init keystone_init(void) } static const char *keystone_match[] __initconst = { - "ti,keystone-evm", + "ti,keystone", NULL, }; diff --git a/arch/arm/mach-mxs/mach-mxs.c b/arch/arm/mach-mxs/mach-mxs.c index 1dc5acd4fc99..2e7cec86e50e 100644 --- a/arch/arm/mach-mxs/mach-mxs.c +++ b/arch/arm/mach-mxs/mach-mxs.c @@ -157,6 +157,8 @@ enum mac_oui { OUI_FSL, OUI_DENX, OUI_CRYSTALFONTZ, + OUI_I2SE, + OUI_ARMADEUS, }; static void __init update_fec_mac_prop(enum mac_oui oui) @@ -211,6 +213,16 @@ static void __init update_fec_mac_prop(enum mac_oui oui) macaddr[1] = 0xb9; macaddr[2] = 0xe1; break; + case OUI_I2SE: + macaddr[0] = 0x00; + macaddr[1] = 0x01; + macaddr[2] = 0x87; + break; + case OUI_ARMADEUS: + macaddr[0] = 0x00; + macaddr[1] = 0x1e; + macaddr[2] = 0xac; + break; } val = ocotp[i]; macaddr[3] = (val >> 16) & 0xff; @@ -236,6 +248,11 @@ static void __init imx28_evk_init(void) mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0); } +static void __init imx28_apf28_init(void) +{ + update_fec_mac_prop(OUI_ARMADEUS); +} + static int apx4devkit_phy_fixup(struct phy_device *phy) { phy->dev_flags |= MICREL_PHY_50MHZ_CLK; @@ -330,6 +347,11 @@ static void __init crystalfontz_init(void) update_fec_mac_prop(OUI_CRYSTALFONTZ); } +static void __init duckbill_init(void) +{ + update_fec_mac_prop(OUI_I2SE); +} + static void __init m28cu3_init(void) { update_fec_mac_prop(OUI_DENX); @@ -426,6 +448,11 @@ static int __init mxs_restart_init(void) return 0; } +static void __init eukrea_mbmx283lc_init(void) +{ + mxs_saif_clkmux_select(MXS_DIGCTL_SAIF_CLKMUX_EXTMSTR0); +} + static void __init mxs_machine_init(void) { struct device_node *root; @@ -458,10 +485,16 @@ static void __init mxs_machine_init(void) if (of_machine_is_compatible("fsl,imx28-evk")) imx28_evk_init(); + if (of_machine_is_compatible("armadeus,imx28-apf28")) + imx28_apf28_init(); else if (of_machine_is_compatible("bluegiga,apx4devkit")) apx4devkit_init(); else if (of_machine_is_compatible("crystalfontz,cfa10036")) crystalfontz_init(); + else if (of_machine_is_compatible("eukrea,mbmx283lc")) + eukrea_mbmx283lc_init(); + else if (of_machine_is_compatible("i2se,duckbill")) + duckbill_init(); else if (of_machine_is_compatible("msr,m28cu3")) m28cu3_init(); diff --git a/arch/arm/mach-omap2/clockdomains3xxx_data.c b/arch/arm/mach-omap2/clockdomains3xxx_data.c index e6b91e552d3d..f03dc97921ad 100644 --- a/arch/arm/mach-omap2/clockdomains3xxx_data.c +++ b/arch/arm/mach-omap2/clockdomains3xxx_data.c @@ -247,7 +247,7 @@ static struct clockdomain neon_clkdm = { static struct clockdomain iva2_clkdm = { .name = "iva2_clkdm", .pwrdm = { .name = "iva2_pwrdm" }, - .flags = CLKDM_CAN_HWSUP_SWSUP, + .flags = CLKDM_CAN_SWSUP, .dep_bit = OMAP3430_PM_WKDEP_MPU_EN_IVA2_SHIFT, .wkdep_srcs = iva2_wkdeps, .clktrctrl_mask = OMAP3430_CLKTRCTRL_IVA2_MASK, diff --git a/arch/arm/mach-omap2/devices.c b/arch/arm/mach-omap2/devices.c index 0dd6398bade4..e58609b312c7 100644 --- a/arch/arm/mach-omap2/devices.c +++ b/arch/arm/mach-omap2/devices.c @@ -229,6 +229,9 @@ static struct omap_iommu_arch_data omap3_isp_iommu = { int omap3_init_camera(struct isp_platform_data *pdata) { + if (of_have_populated_dt()) + omap3_isp_iommu.name = "480bd400.mmu"; + omap3isp_device.dev.platform_data = pdata; omap3isp_device.dev.archdata.iommu = &omap3_isp_iommu; diff --git a/arch/arm/mach-omap2/gpmc-nand.c b/arch/arm/mach-omap2/gpmc-nand.c index 174caecc3186..4349e82debfe 100644 --- a/arch/arm/mach-omap2/gpmc-nand.c +++ b/arch/arm/mach-omap2/gpmc-nand.c @@ -45,24 +45,31 @@ static struct platform_device gpmc_nand_device = { static bool gpmc_hwecc_bch_capable(enum omap_ecc ecc_opt) { - /* support only OMAP3 class */ - if (!cpu_is_omap34xx() && !soc_is_am33xx()) { - pr_err("BCH ecc is not supported on this CPU\n"); + /* platforms which support all ECC schemes */ + if (soc_is_am33xx() || cpu_is_omap44xx() || + soc_is_omap54xx() || soc_is_dra7xx()) + return 1; + + /* OMAP3xxx do not have ELM engine, so cannot support ECC schemes + * which require H/W based ECC error detection */ + if ((cpu_is_omap34xx() || cpu_is_omap3630()) && + ((ecc_opt == OMAP_ECC_BCH4_CODE_HW) || + (ecc_opt == OMAP_ECC_BCH8_CODE_HW))) return 0; - } /* * For now, assume 4-bit mode is only supported on OMAP3630 ES1.x, x>=1 * and AM33xx derivates. Other chips may be added if confirmed to work. */ - if ((ecc_opt == OMAP_ECC_BCH4_CODE_HW) && - (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0)) && - (!soc_is_am33xx())) { - pr_err("BCH 4-bit mode is not supported on this CPU\n"); + if ((ecc_opt == OMAP_ECC_BCH4_CODE_HW_DETECTION_SW) && + (!cpu_is_omap3630() || (GET_OMAP_REVISION() == 0))) return 0; - } - return 1; + /* legacy platforms support only HAM1 (1-bit Hamming) ECC scheme */ + if (ecc_opt == OMAP_ECC_HAM1_CODE_HW) + return 1; + else + return 0; } /* This function will go away once the device-tree convertion is complete */ @@ -133,8 +140,10 @@ int gpmc_nand_init(struct omap_nand_platform_data *gpmc_nand_data, gpmc_update_nand_reg(&gpmc_nand_data->reg, gpmc_nand_data->cs); - if (!gpmc_hwecc_bch_capable(gpmc_nand_data->ecc_opt)) + if (!gpmc_hwecc_bch_capable(gpmc_nand_data->ecc_opt)) { + dev_err(dev, "Unsupported NAND ECC scheme selected\n"); return -EINVAL; + } err = platform_device_register(&gpmc_nand_device); if (err < 0) { diff --git a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c index 4c3b1e6df508..9c7e23aa0e7f 100644 --- a/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_3xxx_data.c @@ -3029,8 +3029,6 @@ static struct omap_hwmod omap3xxx_mmu_isp_hwmod = { .flags = HWMOD_NO_IDLEST, }; -#ifdef CONFIG_OMAP_IOMMU_IVA2 - /* mmu iva */ static struct omap_mmu_dev_attr mmu_iva_dev_attr = { @@ -3070,20 +3068,22 @@ static struct omap_hwmod omap3xxx_mmu_iva_hwmod = { .name = "mmu_iva", .class = &omap3xxx_mmu_hwmod_class, .mpu_irqs = omap3xxx_mmu_iva_irqs, + .clkdm_name = "iva2_clkdm", .rst_lines = omap3xxx_mmu_iva_resets, .rst_lines_cnt = ARRAY_SIZE(omap3xxx_mmu_iva_resets), .main_clk = "iva2_ck", .prcm = { .omap2 = { .module_offs = OMAP3430_IVA2_MOD, + .module_bit = OMAP3430_CM_FCLKEN_IVA2_EN_IVA2_SHIFT, + .idlest_reg_id = 1, + .idlest_idle_bit = OMAP3430_ST_IVA2_SHIFT, }, }, .dev_attr = &mmu_iva_dev_attr, .flags = HWMOD_NO_IDLEST, }; -#endif - /* l4_per -> gpio4 */ static struct omap_hwmod_addr_space omap3xxx_gpio4_addrs[] = { { @@ -3855,9 +3855,7 @@ static struct omap_hwmod_ocp_if *omap34xx_hwmod_ocp_ifs[] __initdata = { &omap3xxx_l4_core__hdq1w, &omap3xxx_sad2d__l3, &omap3xxx_l4_core__mmu_isp, -#ifdef CONFIG_OMAP_IOMMU_IVA2 &omap3xxx_l3_main__mmu_iva, -#endif &omap34xx_l4_core__ssi, NULL }; @@ -3881,9 +3879,7 @@ static struct omap_hwmod_ocp_if *omap36xx_hwmod_ocp_ifs[] __initdata = { &omap3xxx_l4_core__hdq1w, &omap3xxx_sad2d__l3, &omap3xxx_l4_core__mmu_isp, -#ifdef CONFIG_OMAP_IOMMU_IVA2 &omap3xxx_l3_main__mmu_iva, -#endif NULL }; diff --git a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c index e297d6231c3a..892317294fdc 100644 --- a/arch/arm/mach-omap2/omap_hwmod_54xx_data.c +++ b/arch/arm/mach-omap2/omap_hwmod_54xx_data.c @@ -1122,6 +1122,71 @@ static struct omap_hwmod omap54xx_mmc5_hwmod = { }; /* + * 'mmu' class + * The memory management unit performs virtual to physical address translation + * for its requestors. + */ + +static struct omap_hwmod_class_sysconfig omap54xx_mmu_sysc = { + .rev_offs = 0x0000, + .sysc_offs = 0x0010, + .syss_offs = 0x0014, + .sysc_flags = (SYSC_HAS_AUTOIDLE | SYSC_HAS_CLOCKACTIVITY | + SYSC_HAS_SIDLEMODE | SYSC_HAS_SOFTRESET | + SYSS_HAS_RESET_STATUS), + .idlemodes = (SIDLE_FORCE | SIDLE_NO | SIDLE_SMART), + .sysc_fields = &omap_hwmod_sysc_type1, +}; + +static struct omap_hwmod_class omap54xx_mmu_hwmod_class = { + .name = "mmu", + .sysc = &omap54xx_mmu_sysc, +}; + +static struct omap_hwmod_rst_info omap54xx_mmu_dsp_resets[] = { + { .name = "mmu_cache", .rst_shift = 1 }, +}; + +static struct omap_hwmod omap54xx_mmu_dsp_hwmod = { + .name = "mmu_dsp", + .class = &omap54xx_mmu_hwmod_class, + .clkdm_name = "dsp_clkdm", + .rst_lines = omap54xx_mmu_dsp_resets, + .rst_lines_cnt = ARRAY_SIZE(omap54xx_mmu_dsp_resets), + .main_clk = "dpll_iva_h11x2_ck", + .prcm = { + .omap4 = { + .clkctrl_offs = OMAP54XX_CM_DSP_DSP_CLKCTRL_OFFSET, + .rstctrl_offs = OMAP54XX_RM_DSP_RSTCTRL_OFFSET, + .context_offs = OMAP54XX_RM_DSP_DSP_CONTEXT_OFFSET, + .modulemode = MODULEMODE_HWCTRL, + }, + }, +}; + +/* mmu ipu */ +static struct omap_hwmod_rst_info omap54xx_mmu_ipu_resets[] = { + { .name = "mmu_cache", .rst_shift = 2 }, +}; + +static struct omap_hwmod omap54xx_mmu_ipu_hwmod = { + .name = "mmu_ipu", + .class = &omap54xx_mmu_hwmod_class, + .clkdm_name = "ipu_clkdm", + .rst_lines = omap54xx_mmu_ipu_resets, + .rst_lines_cnt = ARRAY_SIZE(omap54xx_mmu_ipu_resets), + .main_clk = "dpll_core_h22x2_ck", + .prcm = { + .omap4 = { + .clkctrl_offs = OMAP54XX_CM_IPU_IPU_CLKCTRL_OFFSET, + .rstctrl_offs = OMAP54XX_RM_IPU_RSTCTRL_OFFSET, + .context_offs = OMAP54XX_RM_IPU_IPU_CONTEXT_OFFSET, + .modulemode = MODULEMODE_HWCTRL, + }, + }, +}; + +/* * 'mpu' class * mpu sub-system */ @@ -1763,6 +1828,14 @@ static struct omap_hwmod_ocp_if omap54xx_l4_cfg__l3_main_1 = { .user = OCP_USER_MPU | OCP_USER_SDMA, }; +/* l4_cfg -> mmu_dsp */ +static struct omap_hwmod_ocp_if omap54xx_l4_cfg__mmu_dsp = { + .master = &omap54xx_l4_cfg_hwmod, + .slave = &omap54xx_mmu_dsp_hwmod, + .clk = "l4_root_clk_div", + .user = OCP_USER_MPU | OCP_USER_SDMA, +}; + /* mpu -> l3_main_1 */ static struct omap_hwmod_ocp_if omap54xx_mpu__l3_main_1 = { .master = &omap54xx_mpu_hwmod, @@ -1787,6 +1860,14 @@ static struct omap_hwmod_ocp_if omap54xx_l4_cfg__l3_main_2 = { .user = OCP_USER_MPU | OCP_USER_SDMA, }; +/* l3_main_2 -> mmu_ipu */ +static struct omap_hwmod_ocp_if omap54xx_l3_main_2__mmu_ipu = { + .master = &omap54xx_l3_main_2_hwmod, + .slave = &omap54xx_mmu_ipu_hwmod, + .clk = "l3_iclk_div", + .user = OCP_USER_MPU | OCP_USER_SDMA, +}; + /* l3_main_1 -> l3_main_3 */ static struct omap_hwmod_ocp_if omap54xx_l3_main_1__l3_main_3 = { .master = &omap54xx_l3_main_1_hwmod, @@ -2345,6 +2426,7 @@ static struct omap_hwmod_ocp_if *omap54xx_hwmod_ocp_ifs[] __initdata = { &omap54xx_l4_wkup__counter_32k, &omap54xx_l4_cfg__dma_system, &omap54xx_l4_abe__dmic, + &omap54xx_l4_cfg__mmu_dsp, &omap54xx_mpu__emif1, &omap54xx_mpu__emif2, &omap54xx_l4_wkup__gpio1, @@ -2360,6 +2442,7 @@ static struct omap_hwmod_ocp_if *omap54xx_hwmod_ocp_ifs[] __initdata = { &omap54xx_l4_per__i2c3, &omap54xx_l4_per__i2c4, &omap54xx_l4_per__i2c5, + &omap54xx_l3_main_2__mmu_ipu, &omap54xx_l4_wkup__kbd, &omap54xx_l4_cfg__mailbox, &omap54xx_l4_abe__mcbsp1, diff --git a/arch/arm/mach-omap2/pdata-quirks.c b/arch/arm/mach-omap2/pdata-quirks.c index c33e07e2f0d4..b04c5f0fc278 100644 --- a/arch/arm/mach-omap2/pdata-quirks.c +++ b/arch/arm/mach-omap2/pdata-quirks.c @@ -16,12 +16,14 @@ #include <linux/wl12xx.h> #include <linux/platform_data/pinctrl-single.h> +#include <linux/platform_data/iommu-omap.h> #include "am35xx.h" #include "common.h" #include "common-board-devices.h" #include "dss-common.h" #include "control.h" +#include "omap_device.h" #include "omap-secure.h" #include "soc.h" @@ -33,20 +35,6 @@ struct pdata_init { struct of_dev_auxdata omap_auxdata_lookup[]; static struct twl4030_gpio_platform_data twl_gpio_auxdata; -/* - * Create alias for USB host PHY clock. - * Remove this when clock phandle can be provided via DT - */ -static void __init __used legacy_init_ehci_clk(char *clkname) -{ - int ret; - - ret = clk_add_alias("main_clk", NULL, clkname, NULL); - if (ret) - pr_err("%s:Failed to add main_clk alias to %s :%d\n", - __func__, clkname, ret); -} - #if IS_ENABLED(CONFIG_WL12XX) static struct wl12xx_platform_data wl12xx __initdata; @@ -94,6 +82,12 @@ static void __init hsmmc2_internal_input_clk(void) omap_ctrl_writel(reg, OMAP343X_CONTROL_DEVCONF1); } +static struct iommu_platform_data omap3_iommu_pdata = { + .reset_name = "mmu", + .assert_reset = omap_device_assert_hardreset, + .deassert_reset = omap_device_deassert_hardreset, +}; + static int omap3_sbc_t3730_twl_callback(struct device *dev, unsigned gpio, unsigned ngpio) @@ -101,7 +95,7 @@ static int omap3_sbc_t3730_twl_callback(struct device *dev, int res; res = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH, - "wlan rst"); + "wlan pwr"); if (res) return res; @@ -110,6 +104,23 @@ static int omap3_sbc_t3730_twl_callback(struct device *dev, return 0; } +static void __init omap3_sbc_t3x_usb_hub_init(int gpio, char *hub_name) +{ + int err = gpio_request_one(gpio, GPIOF_OUT_INIT_LOW, hub_name); + + if (err) { + pr_err("SBC-T3x: %s reset gpio request failed: %d\n", + hub_name, err); + return; + } + + gpio_export(gpio, 0); + + udelay(10); + gpio_set_value(gpio, 1); + msleep(1); +} + static void __init omap3_sbc_t3730_twl_init(void) { twl_gpio_auxdata.setup = omap3_sbc_t3730_twl_callback; @@ -117,10 +128,17 @@ static void __init omap3_sbc_t3730_twl_init(void) static void __init omap3_sbc_t3730_legacy_init(void) { + omap3_sbc_t3x_usb_hub_init(167, "sb-t35 usb hub"); legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 136); omap_ads7846_init(1, 57, 0, NULL); } +static void __init omap3_sbc_t3530_legacy_init(void) +{ + omap3_sbc_t3x_usb_hub_init(167, "sb-t35 usb hub"); + omap_ads7846_init(1, 57, 0, NULL); +} + static void __init omap3_igep0020_legacy_init(void) { omap3_igep2_display_init_of(); @@ -162,7 +180,7 @@ static struct emac_platform_data am35xx_emac_pdata = { .interrupt_disable = am35xx_disable_emac_int, }; -static void __init am3517_evm_legacy_init(void) +static void __init am35xx_emac_reset(void) { u32 v; @@ -172,6 +190,43 @@ static void __init am3517_evm_legacy_init(void) omap_ctrl_readl(AM35XX_CONTROL_IP_SW_RESET); /* OCP barrier */ } +static struct gpio cm_t3517_wlan_gpios[] __initdata = { + { 56, GPIOF_OUT_INIT_HIGH, "wlan pwr" }, + { 4, GPIOF_OUT_INIT_HIGH, "xcvr noe" }, +}; + +static void __init omap3_sbc_t3517_wifi_init(void) +{ + int err = gpio_request_array(cm_t3517_wlan_gpios, + ARRAY_SIZE(cm_t3517_wlan_gpios)); + if (err) { + pr_err("SBC-T3517: wl12xx gpios request failed: %d\n", err); + return; + } + + gpio_export(cm_t3517_wlan_gpios[0].gpio, 0); + gpio_export(cm_t3517_wlan_gpios[1].gpio, 0); + + msleep(100); + gpio_set_value(cm_t3517_wlan_gpios[1].gpio, 0); +} + +static void __init omap3_sbc_t3517_legacy_init(void) +{ + omap3_sbc_t3x_usb_hub_init(152, "cm-t3517 usb hub"); + omap3_sbc_t3x_usb_hub_init(98, "sb-t35 usb hub"); + am35xx_emac_reset(); + hsmmc2_internal_input_clk(); + omap3_sbc_t3517_wifi_init(); + legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 145); + omap_ads7846_init(1, 57, 0, NULL); +} + +static void __init am3517_evm_legacy_init(void) +{ + am35xx_emac_reset(); +} + static void __init nokia_n900_legacy_init(void) { hsmmc2_internal_input_clk(); @@ -200,15 +255,28 @@ static void __init omap4_sdp_legacy_init(void) static void __init omap4_panda_legacy_init(void) { omap4_panda_display_init_of(); - legacy_init_ehci_clk("auxclk3_ck"); legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 53); } #endif +#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5) +static struct iommu_platform_data omap4_iommu_pdata = { + .reset_name = "mmu_cache", + .assert_reset = omap_device_assert_hardreset, + .deassert_reset = omap_device_deassert_hardreset, +}; +#endif + +#ifdef CONFIG_SOC_AM33XX +static void __init am335x_evmsk_legacy_init(void) +{ + legacy_init_wl12xx(WL12XX_REFCLOCK_38, 0, 31); +} +#endif + #ifdef CONFIG_SOC_OMAP5 static void __init omap5_uevm_legacy_init(void) { - legacy_init_ehci_clk("auxclk1_ck"); } #endif @@ -259,6 +327,8 @@ struct of_dev_auxdata omap_auxdata_lookup[] __initdata = { OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002030, "48002030.pinmux", &pcs_pdata), OF_DEV_AUXDATA("ti,omap3-padconf", 0x480025a0, "480025a0.pinmux", &pcs_pdata), OF_DEV_AUXDATA("ti,omap3-padconf", 0x48002a00, "48002a00.pinmux", &pcs_pdata), + OF_DEV_AUXDATA("ti,omap2-iommu", 0x5d000000, "5d000000.mmu", + &omap3_iommu_pdata), /* Only on am3517 */ OF_DEV_AUXDATA("ti,davinci_mdio", 0x5c030000, "davinci_mdio.0", NULL), OF_DEV_AUXDATA("ti,am3517-emac", 0x5c000000, "davinci_emac.0", @@ -268,6 +338,12 @@ struct of_dev_auxdata omap_auxdata_lookup[] __initdata = { OF_DEV_AUXDATA("ti,omap4-padconf", 0x4a100040, "4a100040.pinmux", &pcs_pdata), OF_DEV_AUXDATA("ti,omap4-padconf", 0x4a31e040, "4a31e040.pinmux", &pcs_pdata), #endif +#if defined(CONFIG_ARCH_OMAP4) || defined(CONFIG_SOC_OMAP5) + OF_DEV_AUXDATA("ti,omap4-iommu", 0x4a066000, "4a066000.mmu", + &omap4_iommu_pdata), + OF_DEV_AUXDATA("ti,omap4-iommu", 0x55082000, "55082000.mmu", + &omap4_iommu_pdata), +#endif { /* sentinel */ }, }; @@ -277,6 +353,8 @@ struct of_dev_auxdata omap_auxdata_lookup[] __initdata = { */ static struct pdata_init pdata_quirks[] __initdata = { #ifdef CONFIG_ARCH_OMAP3 + { "compulab,omap3-sbc-t3517", omap3_sbc_t3517_legacy_init, }, + { "compulab,omap3-sbc-t3530", omap3_sbc_t3530_legacy_init, }, { "compulab,omap3-sbc-t3730", omap3_sbc_t3730_legacy_init, }, { "nokia,omap3-n900", nokia_n900_legacy_init, }, { "nokia,omap3-n9", hsmmc2_internal_input_clk, }, @@ -290,6 +368,9 @@ static struct pdata_init pdata_quirks[] __initdata = { { "ti,omap4-sdp", omap4_sdp_legacy_init, }, { "ti,omap4-panda", omap4_panda_legacy_init, }, #endif +#ifdef CONFIG_SOC_AM33XX + { "ti,am335x-evmsk", am335x_evmsk_legacy_init, }, +#endif #ifdef CONFIG_SOC_OMAP5 { "ti,omap5-uevm", omap5_uevm_legacy_init, }, #endif diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig index 8052bd52450d..b41a42da1505 100644 --- a/arch/arm/mach-ux500/Kconfig +++ b/arch/arm/mach-ux500/Kconfig @@ -68,10 +68,6 @@ config UX500_AUTO_PLATFORM a working kernel. If everything else is disabled, this automatically enables MACH_MOP500. -config MACH_UX500_DT - bool "Generic U8500 support using device tree" - depends on MACH_MOP500 - endmenu config UX500_DEBUG_UART diff --git a/arch/arm/mach-ux500/Makefile b/arch/arm/mach-ux500/Makefile index d05ba759da30..de544aabf292 100644 --- a/arch/arm/mach-ux500/Makefile +++ b/arch/arm/mach-ux500/Makefile @@ -7,7 +7,6 @@ obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o obj-$(CONFIG_UX500_SOC_DB8500) += cpu-db8500.o obj-$(CONFIG_MACH_MOP500) += board-mop500-sdi.o \ board-mop500-regulators.o \ - board-mop500-pins.o \ board-mop500-audio.o obj-$(CONFIG_SMP) += platsmp.o headsmp.o obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o diff --git a/arch/arm/mach-ux500/board-mop500-audio.c b/arch/arm/mach-ux500/board-mop500-audio.c index 9309ad4cbd09..b2a0899e7453 100644 --- a/arch/arm/mach-ux500/board-mop500-audio.c +++ b/arch/arm/mach-ux500/board-mop500-audio.c @@ -9,7 +9,6 @@ #include <linux/gpio.h> #include <linux/platform_data/dma-ste-dma40.h> -#include "irqs.h" #include <linux/platform_data/asoc-ux500-msp.h> #include "ste-dma40-db8500.h" diff --git a/arch/arm/mach-ux500/board-mop500-pins.c b/arch/arm/mach-ux500/board-mop500-pins.c deleted file mode 100644 index f63619b69113..000000000000 --- a/arch/arm/mach-ux500/board-mop500-pins.c +++ /dev/null @@ -1,291 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2010 - * - * License terms: GNU General Public License (GPL) version 2 - */ - -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/bug.h> -#include <linux/string.h> -#include <linux/pinctrl/machine.h> -#include <linux/pinctrl/pinconf-generic.h> - -#include <asm/mach-types.h> - -#include "board-mop500.h" - -/* These simply sets bias for pins */ -#define BIAS(a,b) static unsigned long a[] = { b } - -BIAS(abx500_out_lo, PIN_CONF_PACKED(PIN_CONFIG_OUTPUT, 0)); -BIAS(abx500_in_pd, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 1)); -BIAS(abx500_in_nopull, PIN_CONF_PACKED(PIN_CONFIG_BIAS_PULL_DOWN, 0)); - -#define AB8500_MUX_HOG(group, func) \ - PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-ab8500.0", group, func) -#define AB8500_PIN_HOG(pin, conf) \ - PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-ab8500.0", pin, abx500_##conf) - -#define AB8500_MUX_STATE(group, func, dev, state) \ - PIN_MAP_MUX_GROUP(dev, state, "pinctrl-ab8500.0", group, func) -#define AB8500_PIN_STATE(pin, conf, dev, state) \ - PIN_MAP_CONFIGS_PIN(dev, state, "pinctrl-ab8500.0", pin, abx500_##conf) - -#define AB8505_MUX_HOG(group, func) \ - PIN_MAP_MUX_GROUP_HOG_DEFAULT("pinctrl-ab8505.0", group, func) -#define AB8505_PIN_HOG(pin, conf) \ - PIN_MAP_CONFIGS_PIN_HOG_DEFAULT("pinctrl-ab8505.0", pin, abx500_##conf) - -#define AB8505_MUX_STATE(group, func, dev, state) \ - PIN_MAP_MUX_GROUP(dev, state, "pinctrl-ab8505.0", group, func) -#define AB8505_PIN_STATE(pin, conf, dev, state) \ - PIN_MAP_CONFIGS_PIN(dev, state, "pinctrl-ab8505.0", pin, abx500_##conf) - -static struct pinctrl_map __initdata ab8500_pinmap[] = { - /* Sysclkreq2 */ - AB8500_MUX_STATE("sysclkreq2_d_1", "sysclkreq", "regulator.35", PINCTRL_STATE_DEFAULT), - AB8500_PIN_STATE("GPIO1_T10", in_nopull, "regulator.35", PINCTRL_STATE_DEFAULT), - /* sysclkreq2 disable, mux in gpio configured in input pulldown */ - AB8500_MUX_STATE("gpio1_a_1", "gpio", "regulator.35", PINCTRL_STATE_SLEEP), - AB8500_PIN_STATE("GPIO1_T10", in_pd, "regulator.35", PINCTRL_STATE_SLEEP), - - /* pins 2 is muxed in GPIO, configured in INPUT PULL DOWN */ - AB8500_MUX_HOG("gpio2_a_1", "gpio"), - AB8500_PIN_HOG("GPIO2_T9", in_pd), - - /* Sysclkreq4 */ - AB8500_MUX_STATE("sysclkreq4_d_1", "sysclkreq", "regulator.36", PINCTRL_STATE_DEFAULT), - AB8500_PIN_STATE("GPIO3_U9", in_nopull, "regulator.36", PINCTRL_STATE_DEFAULT), - /* sysclkreq4 disable, mux in gpio configured in input pulldown */ - AB8500_MUX_STATE("gpio3_a_1", "gpio", "regulator.36", PINCTRL_STATE_SLEEP), - AB8500_PIN_STATE("GPIO3_U9", in_pd, "regulator.36", PINCTRL_STATE_SLEEP), - - /* pins 4 is muxed in GPIO, configured in INPUT PULL DOWN */ - AB8500_MUX_HOG("gpio4_a_1", "gpio"), - AB8500_PIN_HOG("GPIO4_W2", in_pd), - - /* - * pins 6,7,8 and 9 are muxed in YCBCR0123 - * configured in INPUT PULL UP - */ - AB8500_MUX_HOG("ycbcr0123_d_1", "ycbcr"), - AB8500_PIN_HOG("GPIO6_Y18", in_nopull), - AB8500_PIN_HOG("GPIO7_AA20", in_nopull), - AB8500_PIN_HOG("GPIO8_W18", in_nopull), - AB8500_PIN_HOG("GPIO9_AA19", in_nopull), - - /* - * pins 10,11,12 and 13 are muxed in GPIO - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("gpio10_d_1", "gpio"), - AB8500_PIN_HOG("GPIO10_U17", in_pd), - - AB8500_MUX_HOG("gpio11_d_1", "gpio"), - AB8500_PIN_HOG("GPIO11_AA18", in_pd), - - AB8500_MUX_HOG("gpio12_d_1", "gpio"), - AB8500_PIN_HOG("GPIO12_U16", in_pd), - - AB8500_MUX_HOG("gpio13_d_1", "gpio"), - AB8500_PIN_HOG("GPIO13_W17", in_pd), - - /* - * pins 14,15 are muxed in PWM1 and PWM2 - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("pwmout1_d_1", "pwmout"), - AB8500_PIN_HOG("GPIO14_F14", in_pd), - - AB8500_MUX_HOG("pwmout2_d_1", "pwmout"), - AB8500_PIN_HOG("GPIO15_B17", in_pd), - - /* - * pins 16 is muxed in GPIO - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("gpio16_a_1", "gpio"), - AB8500_PIN_HOG("GPIO14_F14", in_pd), - - /* - * pins 17,18,19 and 20 are muxed in AUDIO interface 1 - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("adi1_d_1", "adi1"), - AB8500_PIN_HOG("GPIO17_P5", in_pd), - AB8500_PIN_HOG("GPIO18_R5", in_pd), - AB8500_PIN_HOG("GPIO19_U5", in_pd), - AB8500_PIN_HOG("GPIO20_T5", in_pd), - - /* - * pins 21,22 and 23 are muxed in USB UICC - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("usbuicc_d_1", "usbuicc"), - AB8500_PIN_HOG("GPIO21_H19", in_pd), - AB8500_PIN_HOG("GPIO22_G20", in_pd), - AB8500_PIN_HOG("GPIO23_G19", in_pd), - - /* - * pins 24,25 are muxed in GPIO - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("gpio24_a_1", "gpio"), - AB8500_PIN_HOG("GPIO24_T14", in_pd), - - AB8500_MUX_HOG("gpio25_a_1", "gpio"), - AB8500_PIN_HOG("GPIO25_R16", in_pd), - - /* - * pins 26 is muxed in GPIO - * configured in OUTPUT LOW - */ - AB8500_MUX_HOG("gpio26_d_1", "gpio"), - AB8500_PIN_HOG("GPIO26_M16", out_lo), - - /* - * pins 27,28 are muxed in DMIC12 - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("dmic12_d_1", "dmic"), - AB8500_PIN_HOG("GPIO27_J6", in_pd), - AB8500_PIN_HOG("GPIO28_K6", in_pd), - - /* - * pins 29,30 are muxed in DMIC34 - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("dmic34_d_1", "dmic"), - AB8500_PIN_HOG("GPIO29_G6", in_pd), - AB8500_PIN_HOG("GPIO30_H6", in_pd), - - /* - * pins 31,32 are muxed in DMIC56 - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("dmic56_d_1", "dmic"), - AB8500_PIN_HOG("GPIO31_F5", in_pd), - AB8500_PIN_HOG("GPIO32_G5", in_pd), - - /* - * pins 34 is muxed in EXTCPENA - * configured INPUT PULL DOWN - */ - AB8500_MUX_HOG("extcpena_d_1", "extcpena"), - AB8500_PIN_HOG("GPIO34_R17", in_pd), - - /* - * pins 35 is muxed in GPIO - * configured in OUTPUT LOW - */ - AB8500_MUX_HOG("gpio35_d_1", "gpio"), - AB8500_PIN_HOG("GPIO35_W15", in_pd), - - /* - * pins 36,37,38 and 39 are muxed in GPIO - * configured in INPUT PULL DOWN - */ - AB8500_MUX_HOG("gpio36_a_1", "gpio"), - AB8500_PIN_HOG("GPIO36_A17", in_pd), - - AB8500_MUX_HOG("gpio37_a_1", "gpio"), - AB8500_PIN_HOG("GPIO37_E15", in_pd), - - AB8500_MUX_HOG("gpio38_a_1", "gpio"), - AB8500_PIN_HOG("GPIO38_C17", in_pd), - - AB8500_MUX_HOG("gpio39_a_1", "gpio"), - AB8500_PIN_HOG("GPIO39_E16", in_pd), - - /* - * pins 40 and 41 are muxed in MODCSLSDA - * configured INPUT PULL DOWN - */ - AB8500_MUX_HOG("modsclsda_d_1", "modsclsda"), - AB8500_PIN_HOG("GPIO40_T19", in_pd), - AB8500_PIN_HOG("GPIO41_U19", in_pd), - - /* - * pins 42 is muxed in GPIO - * configured INPUT PULL DOWN - */ - AB8500_MUX_HOG("gpio42_a_1", "gpio"), - AB8500_PIN_HOG("GPIO42_U2", in_pd), -}; - -static struct pinctrl_map __initdata ab8505_pinmap[] = { - /* Sysclkreq2 */ - AB8505_MUX_STATE("sysclkreq2_d_1", "sysclkreq", "regulator.36", PINCTRL_STATE_DEFAULT), - AB8505_PIN_STATE("GPIO1_N4", in_nopull, "regulator.36", PINCTRL_STATE_DEFAULT), - /* sysclkreq2 disable, mux in gpio configured in input pulldown */ - AB8505_MUX_STATE("gpio1_a_1", "gpio", "regulator.36", PINCTRL_STATE_SLEEP), - AB8505_PIN_STATE("GPIO1_N4", in_pd, "regulator.36", PINCTRL_STATE_SLEEP), - - /* pins 2 is muxed in GPIO, configured in INPUT PULL DOWN */ - AB8505_MUX_HOG("gpio2_a_1", "gpio"), - AB8505_PIN_HOG("GPIO2_R5", in_pd), - - /* Sysclkreq4 */ - AB8505_MUX_STATE("sysclkreq4_d_1", "sysclkreq", "regulator.37", PINCTRL_STATE_DEFAULT), - AB8505_PIN_STATE("GPIO3_P5", in_nopull, "regulator.37", PINCTRL_STATE_DEFAULT), - /* sysclkreq4 disable, mux in gpio configured in input pulldown */ - AB8505_MUX_STATE("gpio3_a_1", "gpio", "regulator.37", PINCTRL_STATE_SLEEP), - AB8505_PIN_STATE("GPIO3_P5", in_pd, "regulator.37", PINCTRL_STATE_SLEEP), - - AB8505_MUX_HOG("gpio10_d_1", "gpio"), - AB8505_PIN_HOG("GPIO10_B16", in_pd), - - AB8505_MUX_HOG("gpio11_d_1", "gpio"), - AB8505_PIN_HOG("GPIO11_B17", in_pd), - - AB8505_MUX_HOG("gpio13_d_1", "gpio"), - AB8505_PIN_HOG("GPIO13_D17", in_nopull), - - AB8505_MUX_HOG("pwmout1_d_1", "pwmout"), - AB8505_PIN_HOG("GPIO14_C16", in_pd), - - AB8505_MUX_HOG("adi2_d_1", "adi2"), - AB8505_PIN_HOG("GPIO17_P2", in_pd), - AB8505_PIN_HOG("GPIO18_N3", in_pd), - AB8505_PIN_HOG("GPIO19_T1", in_pd), - AB8505_PIN_HOG("GPIO20_P3", in_pd), - - AB8505_MUX_HOG("gpio34_a_1", "gpio"), - AB8505_PIN_HOG("GPIO34_H14", in_pd), - - AB8505_MUX_HOG("modsclsda_d_1", "modsclsda"), - AB8505_PIN_HOG("GPIO40_J15", in_pd), - AB8505_PIN_HOG("GPIO41_J14", in_pd), - - AB8505_MUX_HOG("gpio50_d_1", "gpio"), - AB8505_PIN_HOG("GPIO50_L4", in_nopull), - - AB8505_MUX_HOG("resethw_d_1", "resethw"), - AB8505_PIN_HOG("GPIO52_D16", in_pd), - - AB8505_MUX_HOG("service_d_1", "service"), - AB8505_PIN_HOG("GPIO53_D15", in_pd), -}; - -void __init mop500_pinmaps_init(void) -{ - if (machine_is_u8520()) - pinctrl_register_mappings(ab8505_pinmap, - ARRAY_SIZE(ab8505_pinmap)); - else - pinctrl_register_mappings(ab8500_pinmap, - ARRAY_SIZE(ab8500_pinmap)); -} - -void __init snowball_pinmaps_init(void) -{ - pinctrl_register_mappings(ab8500_pinmap, - ARRAY_SIZE(ab8500_pinmap)); -} - -void __init hrefv60_pinmaps_init(void) -{ - pinctrl_register_mappings(ab8500_pinmap, - ARRAY_SIZE(ab8500_pinmap)); -} diff --git a/arch/arm/mach-ux500/board-mop500.h b/arch/arm/mach-ux500/board-mop500.h index d48e8662c676..32cc0d8d8a0e 100644 --- a/arch/arm/mach-ux500/board-mop500.h +++ b/arch/arm/mach-ux500/board-mop500.h @@ -7,78 +7,9 @@ #ifndef __BOARD_MOP500_H #define __BOARD_MOP500_H -/* For NOMADIK_NR_GPIO */ -#include "irqs.h" #include <linux/platform_data/asoc-ux500-msp.h> #include <linux/amba/mmci.h> -/* Snowball specific GPIO assignments, this board has no GPIO expander */ -#define SNOWBALL_ACCEL_INT1_GPIO 163 -#define SNOWBALL_ACCEL_INT2_GPIO 164 -#define SNOWBALL_MAGNET_DRDY_GPIO 165 -#define SNOWBALL_SDMMC_EN_GPIO 217 -#define SNOWBALL_SDMMC_1V8_3V_GPIO 228 -#define SNOWBALL_SDMMC_CD_GPIO 218 - -/* HREFv60-specific GPIO assignments, this board has no GPIO expander */ -#define HREFV60_SDMMC_1V8_3V_GPIO 5 -#define HREFV60_CAMERA_FLASH_ENABLE 21 -#define HREFV60_MAGNET_DRDY_GPIO 32 -#define HREFV60_DISP1_RST_GPIO 65 -#define HREFV60_DISP2_RST_GPIO 66 -#define HREFV60_ACCEL_INT1_GPIO 82 -#define HREFV60_ACCEL_INT2_GPIO 83 -#define HREFV60_SDMMC_CD_GPIO 95 -#define HREFV60_XSHUTDOWN_SECONDARY_SENSOR 140 -#define HREFV60_TOUCH_RST_GPIO 143 -#define HREFV60_HAL_SW_GPIO 145 -#define HREFV60_SDMMC_EN_GPIO 169 -#define HREFV60_MMIO_XENON_CHARGE 170 -#define HREFV60_PROX_SENSE_GPIO 217 - -/* MOP500 generic GPIOs */ -#define CAMERA_FLASH_INT_PIN 7 -#define CYPRESS_TOUCH_INT_PIN 84 -#define XSHUTDOWN_PRIMARY_SENSOR 141 -#define XSHUTDOWN_SECONDARY_SENSOR 142 -#define CYPRESS_TOUCH_RST_GPIO 143 -#define MOP500_HDMI_RST_GPIO 196 -#define CYPRESS_SLAVE_SELECT_GPIO 216 - -/* GPIOs on the TC35892 expander */ -#define MOP500_EGPIO(x) (NOMADIK_NR_GPIO + (x)) -#define GPIO_MAGNET_DRDY MOP500_EGPIO(1) -#define GPIO_SDMMC_CD MOP500_EGPIO(3) -#define GPIO_CAMERA_FLASH_ENABLE MOP500_EGPIO(4) -#define GPIO_MMIO_XENON_CHARGE MOP500_EGPIO(5) -#define GPIO_PROX_SENSOR MOP500_EGPIO(7) -#define GPIO_HAL_SENSOR MOP500_EGPIO(8) -#define GPIO_ACCEL_INT1 MOP500_EGPIO(10) -#define GPIO_ACCEL_INT2 MOP500_EGPIO(11) -#define GPIO_BU21013_CS MOP500_EGPIO(13) -#define MOP500_DISP2_RST_GPIO MOP500_EGPIO(14) -#define MOP500_DISP1_RST_GPIO MOP500_EGPIO(15) -#define GPIO_SDMMC_EN MOP500_EGPIO(17) -#define GPIO_SDMMC_1V8_3V_SEL MOP500_EGPIO(18) -#define MOP500_EGPIO_END MOP500_EGPIO(24) - -/* - * GPIOs on the AB8500 mixed-signals circuit - * Notice that we subtract 1 from the number passed into the macro, this is - * because the AB8500 GPIO pins are enumbered starting from 1, so the value in - * parens matches the GPIO pin number in the data sheet. - */ -#define MOP500_AB8500_PIN_GPIO(x) (MOP500_EGPIO_END + (x) - 1) -/*Snowball AB8500 GPIO */ -#define SNOWBALL_VSMPS2_1V8_GPIO MOP500_AB8500_PIN_GPIO(1) /* SYSCLKREQ2/GPIO1 */ -#define SNOWBALL_PM_GPIO1_GPIO MOP500_AB8500_PIN_GPIO(2) /* SYSCLKREQ3/GPIO2 */ -#define SNOWBALL_WLAN_CLK_REQ_GPIO MOP500_AB8500_PIN_GPIO(3) /* SYSCLKREQ4/GPIO3 */ -#define SNOWBALL_PM_GPIO4_GPIO MOP500_AB8500_PIN_GPIO(4) /* SYSCLKREQ6/GPIO4 */ -#define SNOWBALL_EN_3V6_GPIO MOP500_AB8500_PIN_GPIO(16) /* PWMOUT3/GPIO16 */ -#define SNOWBALL_PME_ETH_GPIO MOP500_AB8500_PIN_GPIO(24) /* SYSCLKREQ7/GPIO24 */ -#define SNOWBALL_EN_3V3_ETH_GPIO MOP500_AB8500_PIN_GPIO(26) /* GPIO26 */ - -struct device; extern struct mmci_platform_data mop500_sdi0_data; extern struct mmci_platform_data mop500_sdi1_data; extern struct mmci_platform_data mop500_sdi2_data; @@ -88,8 +19,4 @@ extern struct msp_i2s_platform_data msp1_platform_data; extern struct msp_i2s_platform_data msp2_platform_data; extern struct msp_i2s_platform_data msp3_platform_data; -void __init mop500_pinmaps_init(void); -void __init snowball_pinmaps_init(void); -void __init hrefv60_pinmaps_init(void); - #endif diff --git a/arch/arm/mach-ux500/cpu-db8500.c b/arch/arm/mach-ux500/cpu-db8500.c index bc8a6183560d..8820f602fcd2 100644 --- a/arch/arm/mach-ux500/cpu-db8500.c +++ b/arch/arm/mach-ux500/cpu-db8500.c @@ -27,7 +27,6 @@ #include <asm/mach/map.h> #include "setup.h" -#include "irqs.h" #include "board-mop500-regulators.h" #include "board-mop500.h" @@ -35,14 +34,11 @@ #include "id.h" struct ab8500_platform_data ab8500_platdata = { - .irq_base = MOP500_AB8500_IRQ_BASE, .regulator = &ab8500_regulator_plat_data, }; struct prcmu_pdata db8500_prcmu_pdata = { .ab_platdata = &ab8500_platdata, - .ab_irq = IRQ_DB8500_AB8500, - .irq_base = IRQ_PRCMU_BASE, .version_offset = DB8500_PRCMU_FW_VERSION_OFFSET, .legacy_offset = DB8500_PRCMU_LEGACY_OFFSET, }; @@ -146,7 +142,6 @@ static struct device * __init db8500_soc_device_init(void) return ux500_soc_device_init(soc_id); } -#ifdef CONFIG_MACH_UX500_DT static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = { /* Requires call-back bindings. */ OF_DEV_AUXDATA("arm,cortex-a9-pmu", 0, "arm-pmu", &db8500_pmu_platdata), @@ -191,16 +186,6 @@ static void __init u8500_init_machine(void) { struct device *parent = db8500_soc_device_init(); - /* Pinmaps must be in place before devices register */ - if (of_machine_is_compatible("st-ericsson,mop500")) - mop500_pinmaps_init(); - else if (of_machine_is_compatible("calaosystems,snowball-a9500")) { - snowball_pinmaps_init(); - } else if (of_machine_is_compatible("st-ericsson,hrefv60+")) - hrefv60_pinmaps_init(); - else if (of_machine_is_compatible("st-ericsson,ccu9540")) {} - /* TODO: Add pinmaps for ccu9540 board. */ - /* automatically probe child nodes of dbx5x0 devices */ if (of_machine_is_compatible("st-ericsson,u8540")) of_platform_populate(NULL, u8500_local_bus_nodes, @@ -229,5 +214,3 @@ DT_MACHINE_START(U8500_DT, "ST-Ericsson Ux5x0 platform (Device Tree Support)") .dt_compat = stericsson_dt_platform_compat, .restart = ux500_restart, MACHINE_END - -#endif diff --git a/arch/arm/mach-ux500/cpu.c b/arch/arm/mach-ux500/cpu.c index d11ac4bf336c..db16b5a04ad5 100644 --- a/arch/arm/mach-ux500/cpu.c +++ b/arch/arm/mach-ux500/cpu.c @@ -52,17 +52,7 @@ void ux500_restart(enum reboot_mode mode, const char *cmd) */ void __init ux500_init_irq(void) { - void __iomem *dist_base; - void __iomem *cpu_base; - gic_arch_extn.flags = IRQCHIP_SKIP_SET_WAKE | IRQCHIP_MASK_ON_SUSPEND; - - if (cpu_is_u8500_family() || cpu_is_ux540_family()) { - dist_base = __io_address(U8500_GIC_DIST_BASE); - cpu_base = __io_address(U8500_GIC_CPU_BASE); - } else - ux500_unknown_soc(); - irqchip_init(); /* diff --git a/arch/arm/mach-ux500/irqs-board-mop500.h b/arch/arm/mach-ux500/irqs-board-mop500.h deleted file mode 100644 index d526dd8e87d3..000000000000 --- a/arch/arm/mach-ux500/irqs-board-mop500.h +++ /dev/null @@ -1,55 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2010 - * - * Author: Rabin Vincent <rabin.vincent@stericsson.com> - * License terms: GNU General Public License (GPL) version 2 - */ - -#ifndef __MACH_IRQS_BOARD_MOP500_H -#define __MACH_IRQS_BOARD_MOP500_H - -/* Number of AB8500 irqs is taken from header file */ -#include <linux/mfd/abx500/ab8500.h> - -#define MOP500_AB8500_IRQ_BASE IRQ_BOARD_START -#define MOP500_AB8500_IRQ_END (MOP500_AB8500_IRQ_BASE \ - + AB8500_MAX_NR_IRQS) - -/* TC35892 */ -#define TC35892_NR_INTERNAL_IRQS 8 -#define TC35892_INT_GPIO(x) (TC35892_NR_INTERNAL_IRQS + (x)) -#define TC35892_NR_GPIOS 24 -#define TC35892_NR_IRQS TC35892_INT_GPIO(TC35892_NR_GPIOS) - -#define MOP500_EGPIO_NR_IRQS TC35892_NR_IRQS - -#define MOP500_EGPIO_IRQ_BASE MOP500_AB8500_IRQ_END -#define MOP500_EGPIO_IRQ_END (MOP500_EGPIO_IRQ_BASE \ - + MOP500_EGPIO_NR_IRQS) -/* STMPE1601 irqs */ -#define STMPE_NR_INTERNAL_IRQS 9 -#define STMPE_INT_GPIO(x) (STMPE_NR_INTERNAL_IRQS + (x)) -#define STMPE_NR_GPIOS 24 -#define STMPE_NR_IRQS STMPE_INT_GPIO(STMPE_NR_GPIOS) - -#define MOP500_STMPE1601_IRQBASE MOP500_EGPIO_IRQ_END -#define MOP500_STMPE1601_IRQ(x) (MOP500_STMPE1601_IRQBASE + (x)) - -#define MOP500_STMPE1601_IRQ_END \ - MOP500_STMPE1601_IRQ(STMPE_NR_INTERNAL_IRQS) - -#define MOP500_NR_IRQS MOP500_STMPE1601_IRQ_END - -#define MOP500_IRQ_END MOP500_NR_IRQS - -/* - * We may have several boards, but only one will run at a - * time, so the one with most IRQs will bump this ahead, - * but the IRQ_BOARD_START remains the same for either board. - */ -#if MOP500_IRQ_END > IRQ_BOARD_END -#undef IRQ_BOARD_END -#define IRQ_BOARD_END MOP500_IRQ_END -#endif - -#endif diff --git a/arch/arm/mach-ux500/irqs-db8500.h b/arch/arm/mach-ux500/irqs-db8500.h deleted file mode 100644 index f3a9d5947ef3..000000000000 --- a/arch/arm/mach-ux500/irqs-db8500.h +++ /dev/null @@ -1,125 +0,0 @@ -/* - * Copyright (C) ST-Ericsson SA 2010 - * - * Author: Rabin Vincent <rabin.vincent@stericsson.com> - * License terms: GNU General Public License (GPL) version 2 - */ - -#ifndef __MACH_IRQS_DB8500_H -#define __MACH_IRQS_DB8500_H - -#define IRQ_DB8500_MTU0 (IRQ_SHPI_START + 4) -#define IRQ_DB8500_SPI2 (IRQ_SHPI_START + 6) -#define IRQ_DB8500_PMU (IRQ_SHPI_START + 7) -#define IRQ_DB8500_SPI0 (IRQ_SHPI_START + 8) -#define IRQ_DB8500_RTT (IRQ_SHPI_START + 9) -#define IRQ_DB8500_PKA (IRQ_SHPI_START + 10) -#define IRQ_DB8500_UART0 (IRQ_SHPI_START + 11) -#define IRQ_DB8500_I2C3 (IRQ_SHPI_START + 12) -#define IRQ_DB8500_L2CC (IRQ_SHPI_START + 13) -#define IRQ_DB8500_SSP0 (IRQ_SHPI_START + 14) -#define IRQ_DB8500_CRYP1 (IRQ_SHPI_START + 15) -#define IRQ_DB8500_MSP1_RX (IRQ_SHPI_START + 16) -#define IRQ_DB8500_MTU1 (IRQ_SHPI_START + 17) -#define IRQ_DB8500_RTC (IRQ_SHPI_START + 18) -#define IRQ_DB8500_UART1 (IRQ_SHPI_START + 19) -#define IRQ_DB8500_USB_WAKEUP (IRQ_SHPI_START + 20) -#define IRQ_DB8500_I2C0 (IRQ_SHPI_START + 21) -#define IRQ_DB8500_I2C1 (IRQ_SHPI_START + 22) -#define IRQ_DB8500_USBOTG (IRQ_SHPI_START + 23) -#define IRQ_DB8500_DMA_SECURE (IRQ_SHPI_START + 24) -#define IRQ_DB8500_DMA (IRQ_SHPI_START + 25) -#define IRQ_DB8500_UART2 (IRQ_SHPI_START + 26) -#define IRQ_DB8500_ICN_PMU1 (IRQ_SHPI_START + 27) -#define IRQ_DB8500_ICN_PMU2 (IRQ_SHPI_START + 28) -#define IRQ_DB8500_HSIR_EXCEP (IRQ_SHPI_START + 29) -#define IRQ_DB8500_MSP0 (IRQ_SHPI_START + 31) -#define IRQ_DB8500_HSIR_CH0_OVRRUN (IRQ_SHPI_START + 32) -#define IRQ_DB8500_HSIR_CH1_OVRRUN (IRQ_SHPI_START + 33) -#define IRQ_DB8500_HSIR_CH2_OVRRUN (IRQ_SHPI_START + 34) -#define IRQ_DB8500_HSIR_CH3_OVRRUN (IRQ_SHPI_START + 35) -#define IRQ_DB8500_HSIR_CH4_OVRRUN (IRQ_SHPI_START + 36) -#define IRQ_DB8500_HSIR_CH5_OVRRUN (IRQ_SHPI_START + 37) -#define IRQ_DB8500_HSIR_CH6_OVRRUN (IRQ_SHPI_START + 38) -#define IRQ_DB8500_HSIR_CH7_OVRRUN (IRQ_SHPI_START + 39) -#define IRQ_DB8500_AB8500 (IRQ_SHPI_START + 40) -#define IRQ_DB8500_SDMMC2 (IRQ_SHPI_START + 41) -#define IRQ_DB8500_SIA (IRQ_SHPI_START + 42) -#define IRQ_DB8500_SIA2 (IRQ_SHPI_START + 43) -#define IRQ_DB8500_SVA (IRQ_SHPI_START + 44) -#define IRQ_DB8500_SVA2 (IRQ_SHPI_START + 45) -#define IRQ_DB8500_PRCMU0 (IRQ_SHPI_START + 46) -#define IRQ_DB8500_PRCMU1 (IRQ_SHPI_START + 47) -#define IRQ_DB8500_DISP (IRQ_SHPI_START + 48) -#define IRQ_DB8500_SPI3 (IRQ_SHPI_START + 49) -#define IRQ_DB8500_SDMMC1 (IRQ_SHPI_START + 50) -#define IRQ_DB8500_I2C4 (IRQ_SHPI_START + 51) -#define IRQ_DB8500_SSP1 (IRQ_SHPI_START + 52) -#define IRQ_DB8500_SKE (IRQ_SHPI_START + 53) -#define IRQ_DB8500_KB (IRQ_SHPI_START + 54) -#define IRQ_DB8500_I2C2 (IRQ_SHPI_START + 55) -#define IRQ_DB8500_B2R2 (IRQ_SHPI_START + 56) -#define IRQ_DB8500_CRYP0 (IRQ_SHPI_START + 57) -#define IRQ_DB8500_SDMMC3 (IRQ_SHPI_START + 59) -#define IRQ_DB8500_SDMMC0 (IRQ_SHPI_START + 60) -#define IRQ_DB8500_HSEM (IRQ_SHPI_START + 61) -#define IRQ_DB8500_MSP1 (IRQ_SHPI_START + 62) -#define IRQ_DB8500_SBAG (IRQ_SHPI_START + 63) -#define IRQ_DB8500_SPI1 (IRQ_SHPI_START + 96) -#define IRQ_DB8500_SRPTIMER (IRQ_SHPI_START + 97) -#define IRQ_DB8500_MSP2 (IRQ_SHPI_START + 98) -#define IRQ_DB8500_SDMMC4 (IRQ_SHPI_START + 99) -#define IRQ_DB8500_SDMMC5 (IRQ_SHPI_START + 100) -#define IRQ_DB8500_HSIRD0 (IRQ_SHPI_START + 104) -#define IRQ_DB8500_HSIRD1 (IRQ_SHPI_START + 105) -#define IRQ_DB8500_HSITD0 (IRQ_SHPI_START + 106) -#define IRQ_DB8500_HSITD1 (IRQ_SHPI_START + 107) -#define IRQ_DB8500_CTI0 (IRQ_SHPI_START + 108) -#define IRQ_DB8500_CTI1 (IRQ_SHPI_START + 109) -#define IRQ_DB8500_ICN_ERR (IRQ_SHPI_START + 110) -#define IRQ_DB8500_MALI_PPMMU (IRQ_SHPI_START + 112) -#define IRQ_DB8500_MALI_PP (IRQ_SHPI_START + 113) -#define IRQ_DB8500_MALI_GPMMU (IRQ_SHPI_START + 114) -#define IRQ_DB8500_MALI_GP (IRQ_SHPI_START + 115) -#define IRQ_DB8500_MALI (IRQ_SHPI_START + 116) -#define IRQ_DB8500_PRCMU_SEM (IRQ_SHPI_START + 118) -#define IRQ_DB8500_GPIO0 (IRQ_SHPI_START + 119) -#define IRQ_DB8500_GPIO1 (IRQ_SHPI_START + 120) -#define IRQ_DB8500_GPIO2 (IRQ_SHPI_START + 121) -#define IRQ_DB8500_GPIO3 (IRQ_SHPI_START + 122) -#define IRQ_DB8500_GPIO4 (IRQ_SHPI_START + 123) -#define IRQ_DB8500_GPIO5 (IRQ_SHPI_START + 124) -#define IRQ_DB8500_GPIO6 (IRQ_SHPI_START + 125) -#define IRQ_DB8500_GPIO7 (IRQ_SHPI_START + 126) -#define IRQ_DB8500_GPIO8 (IRQ_SHPI_START + 127) - -#define IRQ_CA_WAKE_REQ_ED (IRQ_SHPI_START + 71) -#define IRQ_AC_READ_NOTIFICATION_0_ED (IRQ_SHPI_START + 66) -#define IRQ_AC_READ_NOTIFICATION_1_ED (IRQ_SHPI_START + 64) -#define IRQ_CA_MSG_PEND_NOTIFICATION_0_ED (IRQ_SHPI_START + 67) -#define IRQ_CA_MSG_PEND_NOTIFICATION_1_ED (IRQ_SHPI_START + 65) - -#define IRQ_CA_WAKE_REQ_V1 (IRQ_SHPI_START + 83) -#define IRQ_AC_READ_NOTIFICATION_0_V1 (IRQ_SHPI_START + 78) -#define IRQ_AC_READ_NOTIFICATION_1_V1 (IRQ_SHPI_START + 76) -#define IRQ_CA_MSG_PEND_NOTIFICATION_0_V1 (IRQ_SHPI_START + 79) -#define IRQ_CA_MSG_PEND_NOTIFICATION_1_V1 (IRQ_SHPI_START + 77) - -#ifdef CONFIG_UX500_SOC_DB8500 - -/* Virtual interrupts corresponding to the PRCMU wakeups. */ -#define IRQ_PRCMU_BASE IRQ_SOC_START -#define IRQ_PRCMU_END (IRQ_PRCMU_BASE + 23) - -/* - * We may have several SoCs, but only one will run at a - * time, so the one with most IRQs will bump this ahead, - * but the IRQ_SOC_START remains the same for either SoC. - */ -#if IRQ_SOC_END < IRQ_PRCMU_END -#undef IRQ_SOC_END -#define IRQ_SOC_END IRQ_PRCMU_END -#endif - -#endif /* CONFIG_UX500_SOC_DB8500 */ -#endif diff --git a/arch/arm/mach-ux500/irqs.h b/arch/arm/mach-ux500/irqs.h deleted file mode 100644 index 15b2af698ed7..000000000000 --- a/arch/arm/mach-ux500/irqs.h +++ /dev/null @@ -1,49 +0,0 @@ -/* - * Copyright (C) 2008 STMicroelectronics - * Copyright (C) 2009 ST-Ericsson. - * - * This program is free software; you can redistribute it and/or modify - * it under the terms of the GNU General Public License as published by - * the Free Software Foundation; either version 2 of the License, or - * (at your option) any later version. - */ -#ifndef ASM_ARCH_IRQS_H -#define ASM_ARCH_IRQS_H - -#define IRQ_LOCALTIMER 29 -#define IRQ_LOCALWDOG 30 - -/* Shared Peripheral Interrupt (SHPI) */ -#define IRQ_SHPI_START 32 - -/* - * MTU0 preserved for now until plat-nomadik is taught not to use it. Don't - * add any other IRQs here, use the irqs-dbx500.h files. - */ -#define IRQ_MTU0 (IRQ_SHPI_START + 4) - -#define DBX500_NR_INTERNAL_IRQS 166 - -/* After chip-specific IRQ numbers we have the GPIO ones */ -#define NOMADIK_NR_GPIO 288 -#define NOMADIK_GPIO_TO_IRQ(gpio) ((gpio) + DBX500_NR_INTERNAL_IRQS) -#define NOMADIK_IRQ_TO_GPIO(irq) ((irq) - DBX500_NR_INTERNAL_IRQS) -#define IRQ_GPIO_END NOMADIK_GPIO_TO_IRQ(NOMADIK_NR_GPIO) - -#define IRQ_SOC_START IRQ_GPIO_END -/* This will be overridden by SoC-specific irq headers */ -#define IRQ_SOC_END IRQ_SOC_START - -#include "irqs-db8500.h" - -#define IRQ_BOARD_START IRQ_SOC_END -/* This will be overridden by board-specific irq headers */ -#define IRQ_BOARD_END IRQ_BOARD_START - -#ifdef CONFIG_MACH_MOP500 -#include "irqs-board-mop500.h" -#endif - -#define UX500_NR_IRQS IRQ_BOARD_END - -#endif /* ASM_ARCH_IRQS_H */ diff --git a/arch/arm/plat-omap/Kconfig b/arch/arm/plat-omap/Kconfig index 436ea97074cd..02fc10d2d63b 100644 --- a/arch/arm/plat-omap/Kconfig +++ b/arch/arm/plat-omap/Kconfig @@ -86,9 +86,6 @@ config OMAP_MUX_WARNINGS to change the pin multiplexing setup. When there are no warnings printed, it's safe to deselect OMAP_MUX for your product. -config OMAP_IOMMU_IVA2 - bool - config OMAP_MPU_TIMER bool "Use mpu timer" depends on ARCH_OMAP1 diff --git a/drivers/mfd/ab8500-core.c b/drivers/mfd/ab8500-core.c index aaff683cd37d..a8ee4a36a1d8 100644 --- a/drivers/mfd/ab8500-core.c +++ b/drivers/mfd/ab8500-core.c @@ -592,7 +592,7 @@ static int ab8500_irq_init(struct ab8500 *ab8500, struct device_node *np) /* If ->irq_base is zero this will give a linear mapping */ ab8500->domain = irq_domain_add_simple(NULL, - num_irqs, ab8500->irq_base, + num_irqs, 0, &ab8500_irq_ops, ab8500); if (!ab8500->domain) { @@ -1583,14 +1583,13 @@ static int ab8500_probe(struct platform_device *pdev) if (!ab8500) return -ENOMEM; - if (plat) - ab8500->irq_base = plat->irq_base; - ab8500->dev = &pdev->dev; resource = platform_get_resource(pdev, IORESOURCE_IRQ, 0); - if (!resource) + if (!resource) { + dev_err(&pdev->dev, "no IRQ resource\n"); return -ENODEV; + } ab8500->irq = resource->start; @@ -1612,8 +1611,10 @@ static int ab8500_probe(struct platform_device *pdev) else { ret = get_register_interruptible(ab8500, AB8500_MISC, AB8500_IC_NAME_REG, &value); - if (ret < 0) + if (ret < 0) { + dev_err(&pdev->dev, "could not probe HW\n"); return ret; + } ab8500->version = value; } @@ -1759,30 +1760,30 @@ static int ab8500_probe(struct platform_device *pdev) if (is_ab9540(ab8500)) ret = mfd_add_devices(ab8500->dev, 0, ab9540_devs, ARRAY_SIZE(ab9540_devs), NULL, - ab8500->irq_base, ab8500->domain); + 0, ab8500->domain); else if (is_ab8540(ab8500)) { ret = mfd_add_devices(ab8500->dev, 0, ab8540_devs, ARRAY_SIZE(ab8540_devs), NULL, - ab8500->irq_base, NULL); + 0, ab8500->domain); if (ret) return ret; if (is_ab8540_1p2_or_earlier(ab8500)) ret = mfd_add_devices(ab8500->dev, 0, ab8540_cut1_devs, ARRAY_SIZE(ab8540_cut1_devs), NULL, - ab8500->irq_base, NULL); + 0, ab8500->domain); else /* ab8540 >= cut2 */ ret = mfd_add_devices(ab8500->dev, 0, ab8540_cut2_devs, ARRAY_SIZE(ab8540_cut2_devs), NULL, - ab8500->irq_base, NULL); + 0, ab8500->domain); } else if (is_ab8505(ab8500)) ret = mfd_add_devices(ab8500->dev, 0, ab8505_devs, ARRAY_SIZE(ab8505_devs), NULL, - ab8500->irq_base, ab8500->domain); + 0, ab8500->domain); else ret = mfd_add_devices(ab8500->dev, 0, ab8500_devs, ARRAY_SIZE(ab8500_devs), NULL, - ab8500->irq_base, ab8500->domain); + 0, ab8500->domain); if (ret) return ret; @@ -1790,7 +1791,7 @@ static int ab8500_probe(struct platform_device *pdev) /* Add battery management devices */ ret = mfd_add_devices(ab8500->dev, 0, ab8500_bm_devs, ARRAY_SIZE(ab8500_bm_devs), NULL, - ab8500->irq_base, ab8500->domain); + 0, ab8500->domain); if (ret) dev_err(ab8500->dev, "error adding bm devices\n"); } diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c index e43e6e821117..7694e0700d34 100644 --- a/drivers/mfd/db8500-prcmu.c +++ b/drivers/mfd/db8500-prcmu.c @@ -25,6 +25,7 @@ #include <linux/bitops.h> #include <linux/fs.h> #include <linux/of.h> +#include <linux/of_irq.h> #include <linux/platform_device.h> #include <linux/uaccess.h> #include <linux/mfd/core.h> @@ -2678,16 +2679,12 @@ static struct irq_domain_ops db8500_irq_ops = { .xlate = irq_domain_xlate_twocell, }; -static int db8500_irq_init(struct device_node *np, int irq_base) +static int db8500_irq_init(struct device_node *np) { int i; - /* In the device tree case, just take some IRQs */ - if (np) - irq_base = 0; - db8500_irq_domain = irq_domain_add_simple( - np, NUM_PRCMU_WAKEUPS, irq_base, + np, NUM_PRCMU_WAKEUPS, 0, &db8500_irq_ops, NULL); if (!db8500_irq_domain) { @@ -3114,10 +3111,10 @@ static void db8500_prcmu_update_cpufreq(void) } static int db8500_prcmu_register_ab8500(struct device *parent, - struct ab8500_platform_data *pdata, - int irq) + struct ab8500_platform_data *pdata) { - struct resource ab8500_resource = DEFINE_RES_IRQ(irq); + struct device_node *np; + struct resource ab8500_resource; struct mfd_cell ab8500_cell = { .name = "ab8500-core", .of_compatible = "stericsson,ab8500", @@ -3128,6 +3125,20 @@ static int db8500_prcmu_register_ab8500(struct device *parent, .num_resources = 1, }; + if (!parent->of_node) + return -ENODEV; + + /* Look up the device node, sneak the IRQ out of it */ + for_each_child_of_node(parent->of_node, np) { + if (of_device_is_compatible(np, ab8500_cell.of_compatible)) + break; + } + if (!np) { + dev_info(parent, "could not find AB8500 node in the device tree\n"); + return -ENODEV; + } + of_irq_to_resource_table(np, &ab8500_resource, 1); + return mfd_add_devices(parent, 0, &ab8500_cell, 1, NULL, 0, NULL); } @@ -3180,7 +3191,7 @@ static int db8500_prcmu_probe(struct platform_device *pdev) goto no_irq_return; } - db8500_irq_init(np, pdata->irq_base); + db8500_irq_init(np); prcmu_config_esram0_deep_sleep(ESRAM0_DEEP_SLEEP_STATE_RET); @@ -3205,8 +3216,7 @@ static int db8500_prcmu_probe(struct platform_device *pdev) } } - err = db8500_prcmu_register_ab8500(&pdev->dev, pdata->ab_platdata, - pdata->ab_irq); + err = db8500_prcmu_register_ab8500(&pdev->dev, pdata->ab_platdata); if (err) { mfd_remove_devices(&pdev->dev); pr_err("prcmu: Failed to add ab8500 subdevice\n"); diff --git a/include/dt-bindings/pinctrl/am43xx.h b/include/dt-bindings/pinctrl/am43xx.h index eb6c366adfba..9c2e4f82381e 100644 --- a/include/dt-bindings/pinctrl/am43xx.h +++ b/include/dt-bindings/pinctrl/am43xx.h @@ -13,6 +13,7 @@ #define MUX_MODE5 5 #define MUX_MODE6 6 #define MUX_MODE7 7 +#define MUX_MODE8 8 #define PULL_DISABLE (1 << 16) #define PULL_UP (1 << 17) diff --git a/include/dt-bindings/reset-controller/stih415-resets.h b/include/dt-bindings/reset-controller/stih415-resets.h new file mode 100644 index 000000000000..c2f8a66913c5 --- /dev/null +++ b/include/dt-bindings/reset-controller/stih415-resets.h @@ -0,0 +1,26 @@ +/* + * This header provides constants for the reset controller + * based peripheral powerdown requests on the STMicroelectronics + * STiH415 SoC. + */ +#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH415 +#define _DT_BINDINGS_RESET_CONTROLLER_STIH415 + +#define STIH415_EMISS_POWERDOWN 0 +#define STIH415_NAND_POWERDOWN 1 +#define STIH415_KEYSCAN_POWERDOWN 2 +#define STIH415_USB0_POWERDOWN 3 +#define STIH415_USB1_POWERDOWN 4 +#define STIH415_USB2_POWERDOWN 5 +#define STIH415_SATA0_POWERDOWN 6 +#define STIH415_SATA1_POWERDOWN 7 +#define STIH415_PCIE_POWERDOWN 8 + +#define STIH415_ETH0_SOFTRESET 0 +#define STIH415_ETH1_SOFTRESET 1 +#define STIH415_IRB_SOFTRESET 2 +#define STIH415_USB0_SOFTRESET 3 +#define STIH415_USB1_SOFTRESET 4 +#define STIH415_USB2_SOFTRESET 5 + +#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH415 */ diff --git a/include/dt-bindings/reset-controller/stih416-resets.h b/include/dt-bindings/reset-controller/stih416-resets.h new file mode 100644 index 000000000000..2127743f23e3 --- /dev/null +++ b/include/dt-bindings/reset-controller/stih416-resets.h @@ -0,0 +1,50 @@ +/* + * This header provides constants for the reset controller + * based peripheral powerdown requests on the STMicroelectronics + * STiH416 SoC. + */ +#ifndef _DT_BINDINGS_RESET_CONTROLLER_STIH416 +#define _DT_BINDINGS_RESET_CONTROLLER_STIH416 + +#define STIH416_EMISS_POWERDOWN 0 +#define STIH416_NAND_POWERDOWN 1 +#define STIH416_KEYSCAN_POWERDOWN 2 +#define STIH416_USB0_POWERDOWN 3 +#define STIH416_USB1_POWERDOWN 4 +#define STIH416_USB2_POWERDOWN 5 +#define STIH416_USB3_POWERDOWN 6 +#define STIH416_SATA0_POWERDOWN 7 +#define STIH416_SATA1_POWERDOWN 8 +#define STIH416_PCIE0_POWERDOWN 9 +#define STIH416_PCIE1_POWERDOWN 10 + +#define STIH416_ETH0_SOFTRESET 0 +#define STIH416_ETH1_SOFTRESET 1 +#define STIH416_IRB_SOFTRESET 2 +#define STIH416_USB0_SOFTRESET 3 +#define STIH416_USB1_SOFTRESET 4 +#define STIH416_USB2_SOFTRESET 5 +#define STIH416_USB3_SOFTRESET 6 +#define STIH416_SATA0_SOFTRESET 7 +#define STIH416_SATA1_SOFTRESET 8 +#define STIH416_PCIE0_SOFTRESET 9 +#define STIH416_PCIE1_SOFTRESET 10 +#define STIH416_AUD_DAC_SOFTRESET 11 +#define STIH416_HDTVOUT_SOFTRESET 12 +#define STIH416_VTAC_M_RX_SOFTRESET 13 +#define STIH416_VTAC_A_RX_SOFTRESET 14 +#define STIH416_SYNC_HD_SOFTRESET 15 +#define STIH416_SYNC_SD_SOFTRESET 16 +#define STIH416_BLITTER_SOFTRESET 17 +#define STIH416_GPU_SOFTRESET 18 +#define STIH416_VTAC_M_TX_SOFTRESET 19 +#define STIH416_VTAC_A_TX_SOFTRESET 20 +#define STIH416_VTG_AUX_SOFTRESET 21 +#define STIH416_JPEG_DEC_SOFTRESET 22 +#define STIH416_HVA_SOFTRESET 23 +#define STIH416_COMPO_M_SOFTRESET 24 +#define STIH416_COMPO_A_SOFTRESET 25 +#define STIH416_VP8_DEC_SOFTRESET 26 +#define STIH416_VTG_MAIN_SOFTRESET 27 + +#endif /* _DT_BINDINGS_RESET_CONTROLLER_STIH416 */ diff --git a/include/linux/mfd/abx500/ab8500.h b/include/linux/mfd/abx500/ab8500.h index a86ca1406fb8..4e7fe7417fc9 100644 --- a/include/linux/mfd/abx500/ab8500.h +++ b/include/linux/mfd/abx500/ab8500.h @@ -347,7 +347,6 @@ struct ab8500 { struct mutex lock; struct mutex irq_lock; atomic_t transfer_ongoing; - int irq_base; int irq; struct irq_domain *domain; enum ab8500_version version; @@ -378,7 +377,6 @@ struct ab8500_sysctrl_platform_data; * @regulator: machine-specific constraints for regulators */ struct ab8500_platform_data { - int irq_base; void (*init) (struct ab8500 *); struct ab8500_regulator_platform_data *regulator; struct ab8500_codec_platform_data *codec; diff --git a/include/linux/mfd/dbx500-prcmu.h b/include/linux/mfd/dbx500-prcmu.h index 060e11256fbc..bf5109d38a26 100644 --- a/include/linux/mfd/dbx500-prcmu.h +++ b/include/linux/mfd/dbx500-prcmu.h @@ -183,8 +183,6 @@ struct prcmu_pdata bool enable_set_ddr_opp; bool enable_ape_opp_100_voltage; struct ab8500_platform_data *ab_platdata; - int ab_irq; - int irq_base; u32 version_offset; u32 legacy_offset; u32 adt_offset; |