Merge tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux

Pull mtd updates from Miquel Raynal:
 "MTD core changes:
   - Spelling
   - http to https updates

  NAND core changes:
   - Drop useless 'depends on' in Kconfig
   - Add an extra level in the Kconfig hierarchy
   - Trivial spellings
   - Dynamic allocation of the interface configurations
   - Dropping the default ONFI timing mode
   - Various cleanup (types, structures, naming, comments)
   - Hide the chip->data_interface indirection
   - Add the generic rb-gpios property
   - Add the ->choose_interface_config() hook
   - Introduce nand_choose_best_sdr_timings()
   - Use default values for tPROG_max and tBERS_max
   - Avoid redefining tR_max and tCCS_min
   - Add a helper to find the closest ONFI mode
   - bcm63xx MTD parsers: simplify CFE detection

  Raw NAND controller drivers changes:
   - fsl-upm: Deprecation of specific DT properties
   - fsl_upm: Driver rework and cleanup in favor of ->exec_op()
   - Ingenic: Cleanup ARRAY_SIZE() vs sizeof() use
   - brcmnand: ECC error handling on EDU transfers
   - brcmnand: Don't default to EDU transfers
   - qcom: Set BAM mode only if not set already
   - qcom: Avoid write to unavailable register
   - gpio: Driver rework in favor of ->exec_op()
   - tango: ->exec_op() conversion
   - mtk: ->exec_op() conversion

  Raw NAND chip drivers changes:
   - toshiba: Implement ->choose_interface_config() for TH58NVG2S3HBAI4,
     TC58NVG0S3E, and TC58TEG5DCLTA00
   - hynix: Implement ->choose_interface_config() for H27UCG8T2ATR-BC

  SPI NOR core changes:
   - Disable Quad Mode in spi_nor_restore().
   - Don't abort BFPT parsing when QER reserved value is used.
   - Add support/update capabilities for few flashes.
   - Drop s70fl01gs flash: it does not support RDSR(05h) which is
     critical for erase/write.
   - Merge the SPIMEM DTR bits in spi-nor/next to avoid conflicts during
     the release cycle.

  SPI NOR controller drivers changes:
   - Move the cadence-quadspi driver to spi-mem. The series was taken
     through the SPI tree. Merge it also in spi-nor/next to avoid
     conflicts during the release cycle.
   - intel-spi:
      - Add new PCI IDs.
      - Ignore the Write Disable command, the controller doesn't support
        it.
      - Fix performance regression"

* tag 'mtd/for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (79 commits)
  MTD: pfow.h: drop a duplicated word
  MTD: mtd-abi.h: drop a duplicated word
  mtd: rawnand: omap_elm: Replace HTTP links with HTTPS ones
  mtd: Replace HTTP links with HTTPS ones
  mtd: hyperbus: Replace HTTP links with HTTPS ones
  mtd: revert "spi-nor: intel: provide a range for poll_timout"
  mtd: spi-nor: update read capabilities for w25q64 and s25fl064k
  mtd: spi-nor: micron: Add SPI_NOR_DUAL_READ flag on mt25qu02g
  mtd: spi-nor: macronix: Add support for mx66u2g45g
  mtd: spi-nor: intel-spi: Simulate WRDI command
  mtd: spi-nor: Disable the flash quad mode in spi_nor_restore()
  mtd: spi-nor: Add capability to disable flash quad mode
  mtd: spi-nor: spansion: Remove s70fl01gs from flash_info
  mtd: spi-nor: sfdp: do not make invalid quad enable fatal
  dt-bindings: mtd: fsl-upm-nand: Deprecate chip-delay and fsl, upm-wait-flags
  mtd: rawnand: stm32_fmc2: get resources from parent node
  mtd: rawnand: stm32_fmc2: use regmap APIs
  memory: stm32-fmc2-ebi: add STM32 FMC2 EBI controller driver
  dt-bindings: memory-controller: add STM32 FMC2 EBI controller documentation
  dt-bindings: mtd: update STM32 FMC2 NAND controller documentation
  ...

65 files changed, 2788 insertions, 966 deletions

diff --git a/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
new file mode 100644
index 000000000000..70eaf739036b
--- /dev/null
+++ b/Documentation/devicetree/bindings/memory-controllers/st,stm32-fmc2-ebi.yaml
@@ -0,0 +1,252 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/st,stm32-fmc2-ebi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: STMicroelectronics Flexible Memory Controller 2 (FMC2) Bindings
+
+description: |
+  The FMC2 functional block makes the interface with: synchronous and
+  asynchronous static devices (such as PSNOR, PSRAM or other memory-mapped
+  peripherals) and NAND flash memories.
+  Its main purposes are:
+    - to translate AXI transactions into the appropriate external device
+      protocol
+    - to meet the access time requirements of the external devices
+  All external devices share the addresses, data and control signals with the
+  controller. Each external device is accessed by means of a unique Chip
+  Select. The FMC2 performs only one access at a time to an external device.
+
+maintainers:
+  - Christophe Kerello <christophe.kerello@st.com>
+
+properties:
+  compatible:
+    const: st,stm32mp1-fmc2-ebi
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  resets:
+    maxItems: 1
+
+  "#address-cells":
+    const: 2
+
+  "#size-cells":
+    const: 1
+
+  ranges:
+    description: |
+      Reflects the memory layout with four integer values per bank. Format:
+      <bank-number> 0 <address of the bank> <size>
+
+patternProperties:
+  "^.*@[0-4],[a-f0-9]+$":
+    type: object
+
+    properties:
+      reg:
+        description: Bank number, base address and size of the device.
+
+      st,fmc2-ebi-cs-transaction-type:
+        description: |
+          Select one of the transactions type supported
+          0: Asynchronous mode 1 SRAM/FRAM.
+          1: Asynchronous mode 1 PSRAM.
+          2: Asynchronous mode A SRAM/FRAM.
+          3: Asynchronous mode A PSRAM.
+          4: Asynchronous mode 2 NOR.
+          5: Asynchronous mode B NOR.
+          6: Asynchronous mode C NOR.
+          7: Asynchronous mode D NOR.
+          8: Synchronous read synchronous write PSRAM.
+          9: Synchronous read asynchronous write PSRAM.
+          10: Synchronous read synchronous write NOR.
+          11: Synchronous read asynchronous write NOR.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 11
+
+      st,fmc2-ebi-cs-cclk-enable:
+        description: Continuous clock enable (first bank must be configured
+          in synchronous mode). The FMC_CLK is generated continuously
+          during asynchronous and synchronous access. By default, the
+          FMC_CLK is only generated during synchronous access.
+        $ref: /schemas/types.yaml#/definitions/flag
+
+      st,fmc2-ebi-cs-mux-enable:
+        description: Address/Data multiplexed on databus (valid only with
+          NOR and PSRAM transactions type). By default, Address/Data
+          are not multiplexed.
+        $ref: /schemas/types.yaml#/definitions/flag
+
+      st,fmc2-ebi-cs-buswidth:
+        description: Data bus width
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [ 8, 16 ]
+        default: 16
+
+      st,fmc2-ebi-cs-waitpol-high:
+        description: Wait signal polarity (NWAIT signal active high).
+          By default, NWAIT is active low.
+        $ref: /schemas/types.yaml#/definitions/flag
+
+      st,fmc2-ebi-cs-waitcfg-enable:
+        description: The NWAIT signal indicates wheither the data from the
+          device are valid or if a wait state must be inserted when accessing
+          the device in synchronous mode. By default, the NWAIT signal is
+          active one data cycle before wait state.
+        $ref: /schemas/types.yaml#/definitions/flag
+
+      st,fmc2-ebi-cs-wait-enable:
+        description: The NWAIT signal is enabled (its level is taken into
+          account after the programmed latency period to insert wait states
+          if asserted). By default, the NWAIT signal is disabled.
+        $ref: /schemas/types.yaml#/definitions/flag
+
+      st,fmc2-ebi-cs-asyncwait-enable:
+        description: The NWAIT signal is taken into account during asynchronous
+          transactions. By default, the NWAIT signal is not taken into account
+          during asynchronous transactions.
+        $ref: /schemas/types.yaml#/definitions/flag
+
+      st,fmc2-ebi-cs-cpsize:
+        description: CRAM page size. The controller splits the burst access
+          when the memory page is reached. By default, no burst split when
+          crossing page boundary.
+        $ref: /schemas/types.yaml#/definitions/uint32
+        enum: [ 0, 128, 256, 512, 1024 ]
+        default: 0
+
+      st,fmc2-ebi-cs-byte-lane-setup-ns:
+        description: This property configures the byte lane setup timing
+          defined in nanoseconds from NBLx low to Chip Select NEx low.
+
+      st,fmc2-ebi-cs-address-setup-ns:
+        description: This property defines the duration of the address setup
+          phase in nanoseconds used for asynchronous read/write transactions.
+
+      st,fmc2-ebi-cs-address-hold-ns:
+        description: This property defines the duration of the address hold
+          phase in nanoseconds used for asynchronous multiplexed read/write
+          transactions.
+
+      st,fmc2-ebi-cs-data-setup-ns:
+        description: This property defines the duration of the data setup phase
+          in nanoseconds used for asynchronous read/write transactions.
+
+      st,fmc2-ebi-cs-bus-turnaround-ns:
+        description: This property defines the delay in nanoseconds between the
+          end of current read/write transaction and the next transaction.
+
+      st,fmc2-ebi-cs-data-hold-ns:
+        description: This property defines the duration of the data hold phase
+          in nanoseconds used for asynchronous read/write transactions.
+
+      st,fmc2-ebi-cs-clk-period-ns:
+        description: This property defines the FMC_CLK output signal period in
+          nanoseconds.
+
+      st,fmc2-ebi-cs-data-latency-ns:
+        description: This property defines the data latency before reading or
+          writing the first data in nanoseconds.
+
+      st,fmc2_ebi-cs-write-address-setup-ns:
+        description: This property defines the duration of the address setup
+          phase in nanoseconds used for asynchronous write transactions.
+
+      st,fmc2-ebi-cs-write-address-hold-ns:
+        description: This property defines the duration of the address hold
+          phase in nanoseconds used for asynchronous multiplexed write
+          transactions.
+
+      st,fmc2-ebi-cs-write-data-setup-ns:
+        description: This property defines the duration of the data setup
+          phase in nanoseconds used for asynchronous write transactions.
+
+      st,fmc2-ebi-cs-write-bus-turnaround-ns:
+        description: This property defines the delay between the end of current
+          write transaction and the next transaction in nanoseconds.
+
+      st,fmc2-ebi-cs-write-data-hold-ns:
+        description: This property defines the duration of the data hold phase
+          in nanoseconds used for asynchronous write transactions.
+
+      st,fmc2-ebi-cs-max-low-pulse-ns:
+        description: This property defines the maximum chip select low pulse
+          duration in nanoseconds for synchronous transactions. When this timing
+          reaches 0, the controller splits the current access, toggles NE to
+          allow device refresh and restarts a new access.
+
+    required:
+      - reg
+
+required:
+  - "#address-cells"
+  - "#size-cells"
+  - compatible
+  - reg
+  - clocks
+  - ranges
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/stm32mp1-clks.h>
+    #include <dt-bindings/reset/stm32mp1-resets.h>
+    memory-controller@58002000 {
+      #address-cells = <2>;
+      #size-cells = <1>;
+      compatible = "st,stm32mp1-fmc2-ebi";
+      reg = <0x58002000 0x1000>;
+      clocks = <&rcc FMC_K>;
+      resets = <&rcc FMC_R>;
+
+      ranges = <0 0 0x60000000 0x04000000>, /* EBI CS 1 */
+               <1 0 0x64000000 0x04000000>, /* EBI CS 2 */
+               <2 0 0x68000000 0x04000000>, /* EBI CS 3 */
+               <3 0 0x6c000000 0x04000000>, /* EBI CS 4 */
+               <4 0 0x80000000 0x10000000>; /* NAND */
+
+      psram@0,0 {
+        compatible = "mtd-ram";
+        reg = <0 0x00000000 0x100000>;
+        bank-width = <2>;
+
+        st,fmc2-ebi-cs-transaction-type = <1>;
+        st,fmc2-ebi-cs-address-setup-ns = <60>;
+        st,fmc2-ebi-cs-data-setup-ns = <30>;
+        st,fmc2-ebi-cs-bus-turnaround-ns = <5>;
+      };
+
+      nand-controller@4,0 {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        compatible = "st,stm32mp1-fmc2-nfc";
+        reg = <4 0x00000000 0x1000>,
+              <4 0x08010000 0x1000>,
+              <4 0x08020000 0x1000>,
+              <4 0x01000000 0x1000>,
+              <4 0x09010000 0x1000>,
+              <4 0x09020000 0x1000>;
+        interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+        dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>,
+               <&mdma1 20 0x2 0x12000a08 0x0 0x0>,
+               <&mdma1 21 0x2 0x12000a0a 0x0 0x0>;
+        dma-names = "tx", "rx", "ecc";
+
+        nand@0 {
+          reg = <0>;
+          nand-on-flash-bbt;
+          #address-cells = <1>;
+          #size-cells = <1>;
+        };
+      };
+    };
+
+...
diff --git a/Documentation/devicetree/bindings/mtd/davinci-nand.txt b/Documentation/devicetree/bindings/mtd/davinci-nand.txt
index cfb18abe6001..edebeae1f5b3 100644
--- a/Documentation/devicetree/bindings/mtd/davinci-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/davinci-nand.txt
@@ -4,8 +4,8 @@ This file provides information, what the device node for the davinci/keystone
 NAND interface contains.
 
 Documentation:
-Davinci DM646x - http://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
-Kestone - http://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
+Davinci DM646x - https://www.ti.com/lit/ug/sprueq7c/sprueq7c.pdf
+Kestone - https://www.ti.com/lit/ug/sprugz3a/sprugz3a.pdf
 
 Required properties:
 
diff --git a/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt
index fce4894f5a98..25f07c1f9e44 100644
--- a/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt
+++ b/Documentation/devicetree/bindings/mtd/fsl-upm-nand.txt
@@ -7,14 +7,16 @@ Required properties:
 - fsl,upm-cmd-offset : UPM pattern offset for the command latch.
 
 Optional properties:
-- fsl,upm-wait-flags : add chip-dependent short delays after running the
-	UPM pattern (0x1), after writing a data byte (0x2) or after
-	writing out a buffer (0x4).
 - fsl,upm-addr-line-cs-offsets : address offsets for multi-chip support.
 	The corresponding address lines are used to select the chip.
 - gpios : may specify optional GPIOs connected to the Ready-Not-Busy pins
 	(R/B#). For multi-chip devices, "n" GPIO definitions are required
 	according to the number of chips.
+
+Deprecated properties:
+- fsl,upm-wait-flags : add chip-dependent short delays after running the
+	UPM pattern (0x1), after writing a data byte (0x2) or after
+	writing out a buffer (0x4).
 - chip-delay : chip dependent delay for transferring data from array to
 	read registers (tR). Required if property "gpios" is not used
 	(R/B# pins not connected).
@@ -52,8 +54,6 @@ upm@3,0 {
 	fsl,upm-cmd-offset = <0x08>;
 	/* Multi-chip NAND device */
 	fsl,upm-addr-line-cs-offsets = <0x0 0x200>;
-	fsl,upm-wait-flags = <0x5>;
-	chip-delay = <25>; // in micro-seconds
 
 	nand@0 {
 		#address-cells = <1>;
diff --git a/Documentation/devicetree/bindings/mtd/nand-controller.yaml b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
index cde7c4d79efe..40fc5b0b2b8c 100644
--- a/Documentation/devicetree/bindings/mtd/nand-controller.yaml
+++ b/Documentation/devicetree/bindings/mtd/nand-controller.yaml
@@ -114,6 +114,13 @@ patternProperties:
         description:
           Contains the native Ready/Busy IDs.
 
+      rb-gpios:
+        description:
+          Contains one or more GPIO descriptor (the numper of descriptor
+          depends on the number of R/B pins exposed by the flash) for the
+          Ready/Busy pins. Active state refers to the NAND ready state and
+          should be set to GPIOD_ACTIVE_HIGH unless the signal is inverted.
+
     required:
       - reg
 
diff --git a/Documentation/devicetree/bindings/mtd/st,stm32-fmc2-nand.yaml b/Documentation/devicetree/bindings/mtd/st,stm32-fmc2-nand.yaml
index b059267f6d20..6ae7de15d172 100644
--- a/Documentation/devicetree/bindings/mtd/st,stm32-fmc2-nand.yaml
+++ b/Documentation/devicetree/bindings/mtd/st,stm32-fmc2-nand.yaml
@@ -9,32 +9,19 @@ title: STMicroelectronics Flexible Memory Controller 2 (FMC2) Bindings
 maintainers:
   - Christophe Kerello <christophe.kerello@st.com>
 
-allOf:
-  - $ref: "nand-controller.yaml#"
-
 properties:
   compatible:
-    const: st,stm32mp15-fmc2
+    enum:
+      - st,stm32mp15-fmc2
+      - st,stm32mp1-fmc2-nfc
 
   reg:
-    items:
-      - description: Registers
-      - description: Chip select 0 data
-      - description: Chip select 0 command
-      - description: Chip select 0 address space
-      - description: Chip select 1 data
-      - description: Chip select 1 command
-      - description: Chip select 1 address space
+    minItems: 6
+    maxItems: 7
 
   interrupts:
     maxItems: 1
 
-  clocks:
-    maxItems: 1
-
-  resets:
-    maxItems: 1
-
   dmas:
     items:
       - description: tx DMA channel
@@ -57,11 +44,55 @@ patternProperties:
       nand-ecc-strength:
         enum: [1, 4 ,8 ]
 
+allOf:
+  - $ref: "nand-controller.yaml#"
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: st,stm32mp15-fmc2
+    then:
+      properties:
+        reg:
+          items:
+            - description: Registers
+            - description: Chip select 0 data
+            - description: Chip select 0 command
+            - description: Chip select 0 address space
+            - description: Chip select 1 data
+            - description: Chip select 1 command
+            - description: Chip select 1 address space
+
+        clocks:
+          maxItems: 1
+
+        resets:
+          maxItems: 1
+
+      required:
+        - clocks
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: st,stm32mp1-fmc2-nfc
+    then:
+      properties:
+        reg:
+          items:
+            - description: Chip select 0 data
+            - description: Chip select 0 command
+            - description: Chip select 0 address space
+            - description: Chip select 1 data
+            - description: Chip select 1 command
+            - description: Chip select 1 address space
+
 required:
   - compatible
   - reg
   - interrupts
-  - clocks
 
 examples:
   - |
@@ -77,13 +108,13 @@ examples:
             <0x81000000 0x1000>,
             <0x89010000 0x1000>,
             <0x89020000 0x1000>;
-            interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
-            dmas = <&mdma1 20 0x10 0x12000a02 0x0 0x0>,
-                   <&mdma1 20 0x10 0x12000a08 0x0 0x0>,
-                   <&mdma1 21 0x10 0x12000a0a 0x0 0x0>;
-            dma-names = "tx", "rx", "ecc";
-            clocks = <&rcc FMC_K>;
-            resets = <&rcc FMC_R>;
+      interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+      dmas = <&mdma1 20 0x2 0x12000a02 0x0 0x0>,
+             <&mdma1 20 0x2 0x12000a08 0x0 0x0>,
+             <&mdma1 21 0x2 0x12000a0a 0x0 0x0>;
+      dma-names = "tx", "rx", "ecc";
+      clocks = <&rcc FMC_K>;
+      resets = <&rcc FMC_R>;
       #address-cells = <1>;
       #size-cells = <0>;
 
diff --git a/drivers/memory/Kconfig b/drivers/memory/Kconfig
index 97440af499b0..2c79e95dd486 100644
--- a/drivers/memory/Kconfig
+++ b/drivers/memory/Kconfig
@@ -188,6 +188,16 @@ config RENESAS_RPCIF
 	  host or HyperFlash. You'll have to select individual components
 	  under the corresponding menu.
 
+config STM32_FMC2_EBI
+	tristate "Support for FMC2 External Bus Interface on STM32MP SoCs"
+	depends on MACH_STM32MP157 || COMPILE_TEST
+	select MFD_SYSCON
+	help
+	  Select this option to enable the STM32 FMC2 External Bus Interface
+	  controller. This driver configures the transactions with external
+	  devices (like SRAM, ethernet adapters, FPGAs, LCD displays, ...) on
+	  SOCs containing the FMC2 External Bus Interface.
+
 source "drivers/memory/samsung/Kconfig"
 source "drivers/memory/tegra/Kconfig"
 
diff --git a/drivers/memory/Makefile b/drivers/memory/Makefile
index d105f8ebe8b8..b4533ffff2bc 100644
--- a/drivers/memory/Makefile
+++ b/drivers/memory/Makefile
@@ -23,6 +23,7 @@ obj-$(CONFIG_MTK_SMI)		+= mtk-smi.o
 obj-$(CONFIG_DA8XX_DDRCTL)	+= da8xx-ddrctl.o
 obj-$(CONFIG_PL353_SMC)		+= pl353-smc.o
 obj-$(CONFIG_RENESAS_RPCIF)	+= renesas-rpc-if.o
+obj-$(CONFIG_STM32_FMC2_EBI)	+= stm32-fmc2-ebi.o
 
 obj-$(CONFIG_SAMSUNG_MC)	+= samsung/
 obj-$(CONFIG_TEGRA_MC)		+= tegra/
diff --git a/drivers/memory/stm32-fmc2-ebi.c b/drivers/memory/stm32-fmc2-ebi.c
new file mode 100644
index 000000000000..4d5758c419c5
--- /dev/null
+++ b/drivers/memory/stm32-fmc2-ebi.c
@@ -0,0 +1,1206 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) STMicroelectronics 2020
+ */
+
+#include <linux/bitfield.h>
+#include <linux/clk.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/regmap.h>
+#include <linux/reset.h>
+
+/* FMC2 Controller Registers */
+#define FMC2_BCR1			0x0
+#define FMC2_BTR1			0x4
+#define FMC2_BCR(x)			((x) * 0x8 + FMC2_BCR1)
+#define FMC2_BTR(x)			((x) * 0x8 + FMC2_BTR1)
+#define FMC2_PCSCNTR			0x20
+#define FMC2_BWTR1			0x104
+#define FMC2_BWTR(x)			((x) * 0x8 + FMC2_BWTR1)
+
+/* Register: FMC2_BCR1 */
+#define FMC2_BCR1_CCLKEN		BIT(20)
+#define FMC2_BCR1_FMC2EN		BIT(31)
+
+/* Register: FMC2_BCRx */
+#define FMC2_BCR_MBKEN			BIT(0)
+#define FMC2_BCR_MUXEN			BIT(1)
+#define FMC2_BCR_MTYP			GENMASK(3, 2)
+#define FMC2_BCR_MWID			GENMASK(5, 4)
+#define FMC2_BCR_FACCEN			BIT(6)
+#define FMC2_BCR_BURSTEN		BIT(8)
+#define FMC2_BCR_WAITPOL		BIT(9)
+#define FMC2_BCR_WAITCFG		BIT(11)
+#define FMC2_BCR_WREN			BIT(12)
+#define FMC2_BCR_WAITEN			BIT(13)
+#define FMC2_BCR_EXTMOD			BIT(14)
+#define FMC2_BCR_ASYNCWAIT		BIT(15)
+#define FMC2_BCR_CPSIZE			GENMASK(18, 16)
+#define FMC2_BCR_CBURSTRW		BIT(19)
+#define FMC2_BCR_NBLSET			GENMASK(23, 22)
+
+/* Register: FMC2_BTRx/FMC2_BWTRx */
+#define FMC2_BXTR_ADDSET		GENMASK(3, 0)
+#define FMC2_BXTR_ADDHLD		GENMASK(7, 4)
+#define FMC2_BXTR_DATAST		GENMASK(15, 8)
+#define FMC2_BXTR_BUSTURN		GENMASK(19, 16)
+#define FMC2_BTR_CLKDIV			GENMASK(23, 20)
+#define FMC2_BTR_DATLAT			GENMASK(27, 24)
+#define FMC2_BXTR_ACCMOD		GENMASK(29, 28)
+#define FMC2_BXTR_DATAHLD		GENMASK(31, 30)
+
+/* Register: FMC2_PCSCNTR */
+#define FMC2_PCSCNTR_CSCOUNT		GENMASK(15, 0)
+#define FMC2_PCSCNTR_CNTBEN(x)		BIT((x) + 16)
+
+#define FMC2_MAX_EBI_CE			4
+#define FMC2_MAX_BANKS			5
+
+#define FMC2_BCR_CPSIZE_0		0x0
+#define FMC2_BCR_CPSIZE_128		0x1
+#define FMC2_BCR_CPSIZE_256		0x2
+#define FMC2_BCR_CPSIZE_512		0x3
+#define FMC2_BCR_CPSIZE_1024		0x4
+
+#define FMC2_BCR_MWID_8			0x0
+#define FMC2_BCR_MWID_16		0x1
+
+#define FMC2_BCR_MTYP_SRAM		0x0
+#define FMC2_BCR_MTYP_PSRAM		0x1
+#define FMC2_BCR_MTYP_NOR		0x2
+
+#define FMC2_BXTR_EXTMOD_A		0x0
+#define FMC2_BXTR_EXTMOD_B		0x1
+#define FMC2_BXTR_EXTMOD_C		0x2
+#define FMC2_BXTR_EXTMOD_D		0x3
+
+#define FMC2_BCR_NBLSET_MAX		0x3
+#define FMC2_BXTR_ADDSET_MAX		0xf
+#define FMC2_BXTR_ADDHLD_MAX		0xf
+#define FMC2_BXTR_DATAST_MAX		0xff
+#define FMC2_BXTR_BUSTURN_MAX		0xf
+#define FMC2_BXTR_DATAHLD_MAX		0x3
+#define FMC2_BTR_CLKDIV_MAX		0xf
+#define FMC2_BTR_DATLAT_MAX		0xf
+#define FMC2_PCSCNTR_CSCOUNT_MAX	0xff
+
+enum stm32_fmc2_ebi_bank {
+	FMC2_EBI1 = 0,
+	FMC2_EBI2,
+	FMC2_EBI3,
+	FMC2_EBI4,
+	FMC2_NAND
+};
+
+enum stm32_fmc2_ebi_register_type {
+	FMC2_REG_BCR = 1,
+	FMC2_REG_BTR,
+	FMC2_REG_BWTR,
+	FMC2_REG_PCSCNTR
+};
+
+enum stm32_fmc2_ebi_transaction_type {
+	FMC2_ASYNC_MODE_1_SRAM = 0,
+	FMC2_ASYNC_MODE_1_PSRAM,
+	FMC2_ASYNC_MODE_A_SRAM,
+	FMC2_ASYNC_MODE_A_PSRAM,
+	FMC2_ASYNC_MODE_2_NOR,
+	FMC2_ASYNC_MODE_B_NOR,
+	FMC2_ASYNC_MODE_C_NOR,
+	FMC2_ASYNC_MODE_D_NOR,
+	FMC2_SYNC_READ_SYNC_WRITE_PSRAM,
+	FMC2_SYNC_READ_ASYNC_WRITE_PSRAM,
+	FMC2_SYNC_READ_SYNC_WRITE_NOR,
+	FMC2_SYNC_READ_ASYNC_WRITE_NOR
+};
+
+enum stm32_fmc2_ebi_buswidth {
+	FMC2_BUSWIDTH_8 = 8,
+	FMC2_BUSWIDTH_16 = 16
+};
+
+enum stm32_fmc2_ebi_cpsize {
+	FMC2_CPSIZE_0 = 0,
+	FMC2_CPSIZE_128 = 128,
+	FMC2_CPSIZE_256 = 256,
+	FMC2_CPSIZE_512 = 512,
+	FMC2_CPSIZE_1024 = 1024
+};
+
+struct stm32_fmc2_ebi {
+	struct device *dev;
+	struct clk *clk;
+	struct regmap *regmap;
+	u8 bank_assigned;
+
+	u32 bcr[FMC2_MAX_EBI_CE];
+	u32 btr[FMC2_MAX_EBI_CE];
+	u32 bwtr[FMC2_MAX_EBI_CE];
+	u32 pcscntr;
+};
+
+/*
+ * struct stm32_fmc2_prop - STM32 FMC2 EBI property
+ * @name: the device tree binding name of the property
+ * @bprop: indicate that it is a boolean property
+ * @mprop: indicate that it is a mandatory property
+ * @reg_type: the register that have to be modified
+ * @reg_mask: the bit that have to be modified in the selected register
+ *            in case of it is a boolean property
+ * @reset_val: the default value that have to be set in case the property
+ *             has not been defined in the device tree
+ * @check: this callback ckecks that the property is compliant with the
+ *         transaction type selected
+ * @calculate: this callback is called to calculate for exemple a timing
+ *             set in nanoseconds in the device tree in clock cycles or in
+ *             clock period
+ * @set: this callback applies the values in the registers
+ */
+struct stm32_fmc2_prop {
+	const char *name;
+	bool bprop;
+	bool mprop;
+	int reg_type;
+	u32 reg_mask;
+	u32 reset_val;
+	int (*check)(struct stm32_fmc2_ebi *ebi,
+		     const struct stm32_fmc2_prop *prop, int cs);
+	u32 (*calculate)(struct stm32_fmc2_ebi *ebi, int cs, u32 setup);
+	int (*set)(struct stm32_fmc2_ebi *ebi,
+		   const struct stm32_fmc2_prop *prop,
+		   int cs, u32 setup);
+};
+
+static int stm32_fmc2_ebi_check_mux(struct stm32_fmc2_ebi *ebi,
+				    const struct stm32_fmc2_prop *prop,
+				    int cs)
+{
+	u32 bcr;
+
+	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+
+	if (bcr & FMC2_BCR_MTYP)
+		return 0;
+
+	return -EINVAL;
+}
+
+static int stm32_fmc2_ebi_check_waitcfg(struct stm32_fmc2_ebi *ebi,
+					const struct stm32_fmc2_prop *prop,
+					int cs)
+{
+	u32 bcr, val = FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_NOR);
+
+	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+
+	if ((bcr & FMC2_BCR_MTYP) == val && bcr & FMC2_BCR_BURSTEN)
+		return 0;
+
+	return -EINVAL;
+}
+
+static int stm32_fmc2_ebi_check_sync_trans(struct stm32_fmc2_ebi *ebi,
+					   const struct stm32_fmc2_prop *prop,
+					   int cs)
+{
+	u32 bcr;
+
+	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+
+	if (bcr & FMC2_BCR_BURSTEN)
+		return 0;
+
+	return -EINVAL;
+}
+
+static int stm32_fmc2_ebi_check_async_trans(struct stm32_fmc2_ebi *ebi,
+					    const struct stm32_fmc2_prop *prop,
+					    int cs)
+{
+	u32 bcr;
+
+	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+
+	if (!(bcr & FMC2_BCR_BURSTEN) || !(bcr & FMC2_BCR_CBURSTRW))
+		return 0;
+
+	return -EINVAL;
+}
+
+static int stm32_fmc2_ebi_check_cpsize(struct stm32_fmc2_ebi *ebi,
+				       const struct stm32_fmc2_prop *prop,
+				       int cs)
+{
+	u32 bcr, val = FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_PSRAM);
+
+	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+
+	if ((bcr & FMC2_BCR_MTYP) == val && bcr & FMC2_BCR_BURSTEN)
+		return 0;
+
+	return -EINVAL;
+}
+
+static int stm32_fmc2_ebi_check_address_hold(struct stm32_fmc2_ebi *ebi,
+					     const struct stm32_fmc2_prop *prop,
+					     int cs)
+{
+	u32 bcr, bxtr, val = FIELD_PREP(FMC2_BXTR_ACCMOD, FMC2_BXTR_EXTMOD_D);
+
+	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	if (prop->reg_type == FMC2_REG_BWTR)
+		regmap_read(ebi->regmap, FMC2_BWTR(cs), &bxtr);
+	else
+		regmap_read(ebi->regmap, FMC2_BTR(cs), &bxtr);
+
+	if ((!(bcr & FMC2_BCR_BURSTEN) || !(bcr & FMC2_BCR_CBURSTRW)) &&
+	    ((bxtr & FMC2_BXTR_ACCMOD) == val || bcr & FMC2_BCR_MUXEN))
+		return 0;
+
+	return -EINVAL;
+}
+
+static int stm32_fmc2_ebi_check_clk_period(struct stm32_fmc2_ebi *ebi,
+					   const struct stm32_fmc2_prop *prop,
+					   int cs)
+{
+	u32 bcr, bcr1;
+
+	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	if (cs)
+		regmap_read(ebi->regmap, FMC2_BCR1, &bcr1);
+	else
+		bcr1 = bcr;
+
+	if (bcr & FMC2_BCR_BURSTEN && (!cs || !(bcr1 & FMC2_BCR1_CCLKEN)))
+		return 0;
+
+	return -EINVAL;
+}
+
+static int stm32_fmc2_ebi_check_cclk(struct stm32_fmc2_ebi *ebi,
+				     const struct stm32_fmc2_prop *prop,
+				     int cs)
+{
+	if (cs)
+		return -EINVAL;
+
+	return stm32_fmc2_ebi_check_sync_trans(ebi, prop, cs);
+}
+
+static u32 stm32_fmc2_ebi_ns_to_clock_cycles(struct stm32_fmc2_ebi *ebi,
+					     int cs, u32 setup)
+{
+	unsigned long hclk = clk_get_rate(ebi->clk);
+	unsigned long hclkp = NSEC_PER_SEC / (hclk / 1000);
+
+	return DIV_ROUND_UP(setup * 1000, hclkp);
+}
+
+static u32 stm32_fmc2_ebi_ns_to_clk_period(struct stm32_fmc2_ebi *ebi,
+					   int cs, u32 setup)
+{
+	u32 nb_clk_cycles = stm32_fmc2_ebi_ns_to_clock_cycles(ebi, cs, setup);
+	u32 bcr, btr, clk_period;
+
+	regmap_read(ebi->regmap, FMC2_BCR1, &bcr);
+	if (bcr & FMC2_BCR1_CCLKEN || !cs)
+		regmap_read(ebi->regmap, FMC2_BTR1, &btr);
+	else
+		regmap_read(ebi->regmap, FMC2_BTR(cs), &btr);
+
+	clk_period = FIELD_GET(FMC2_BTR_CLKDIV, btr) + 1;
+
+	return DIV_ROUND_UP(nb_clk_cycles, clk_period);
+}
+
+static int stm32_fmc2_ebi_get_reg(int reg_type, int cs, u32 *reg)
+{
+	switch (reg_type) {
+	case FMC2_REG_BCR:
+		*reg = FMC2_BCR(cs);
+		break;
+	case FMC2_REG_BTR:
+		*reg = FMC2_BTR(cs);
+		break;
+	case FMC2_REG_BWTR:
+		*reg = FMC2_BWTR(cs);
+		break;
+	case FMC2_REG_PCSCNTR:
+		*reg = FMC2_PCSCNTR;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_set_bit_field(struct stm32_fmc2_ebi *ebi,
+					const struct stm32_fmc2_prop *prop,
+					int cs, u32 setup)
+{
+	u32 reg;
+	int ret;
+
+	ret = stm32_fmc2_ebi_get_reg(prop->reg_type, cs, &reg);
+	if (ret)
+		return ret;
+
+	regmap_update_bits(ebi->regmap, reg, prop->reg_mask,
+			   setup ? prop->reg_mask : 0);
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_set_trans_type(struct stm32_fmc2_ebi *ebi,
+					 const struct stm32_fmc2_prop *prop,
+					 int cs, u32 setup)
+{
+	u32 bcr_mask, bcr = FMC2_BCR_WREN;
+	u32 btr_mask, btr = 0;
+	u32 bwtr_mask, bwtr = 0;
+
+	bwtr_mask = FMC2_BXTR_ACCMOD;
+	btr_mask = FMC2_BXTR_ACCMOD;
+	bcr_mask = FMC2_BCR_MUXEN | FMC2_BCR_MTYP | FMC2_BCR_FACCEN |
+		   FMC2_BCR_WREN | FMC2_BCR_WAITEN | FMC2_BCR_BURSTEN |
+		   FMC2_BCR_EXTMOD | FMC2_BCR_CBURSTRW;
+
+	switch (setup) {
+	case FMC2_ASYNC_MODE_1_SRAM:
+		bcr |= FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_SRAM);
+		/*
+		 * MUXEN = 0, MTYP = 0, FACCEN = 0, BURSTEN = 0, WAITEN = 0,
+		 * WREN = 1, EXTMOD = 0, CBURSTRW = 0, ACCMOD = 0
+		 */
+		break;
+	case FMC2_ASYNC_MODE_1_PSRAM:
+		/*
+		 * MUXEN = 0, MTYP = 1, FACCEN = 0, BURSTEN = 0, WAITEN = 0,
+		 * WREN = 1, EXTMOD = 0, CBURSTRW = 0, ACCMOD = 0
+		 */
+		bcr |= FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_PSRAM);
+		break;
+	case FMC2_ASYNC_MODE_A_SRAM:
+		/*
+		 * MUXEN = 0, MTYP = 0, FACCEN = 0, BURSTEN = 0, WAITEN = 0,
+		 * WREN = 1, EXTMOD = 1, CBURSTRW = 0, ACCMOD = 0
+		 */
+		bcr |= FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_SRAM);
+		bcr |= FMC2_BCR_EXTMOD;
+		btr |= FIELD_PREP(FMC2_BXTR_ACCMOD, FMC2_BXTR_EXTMOD_A);
+		bwtr |= FIELD_PREP(FMC2_BXTR_ACCMOD, FMC2_BXTR_EXTMOD_A);
+		break;
+	case FMC2_ASYNC_MODE_A_PSRAM:
+		/*
+		 * MUXEN = 0, MTYP = 1, FACCEN = 0, BURSTEN = 0, WAITEN = 0,
+		 * WREN = 1, EXTMOD = 1, CBURSTRW = 0, ACCMOD = 0
+		 */
+		bcr |= FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_PSRAM);
+		bcr |= FMC2_BCR_EXTMOD;
+		btr |= FIELD_PREP(FMC2_BXTR_ACCMOD, FMC2_BXTR_EXTMOD_A);
+		bwtr |= FIELD_PREP(FMC2_BXTR_ACCMOD, FMC2_BXTR_EXTMOD_A);
+		break;
+	case FMC2_ASYNC_MODE_2_NOR:
+		/*
+		 * MUXEN = 0, MTYP = 2, FACCEN = 1, BURSTEN = 0, WAITEN = 0,
+		 * WREN = 1, EXTMOD = 0, CBURSTRW = 0, ACCMOD = 0
+		 */
+		bcr |= FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_NOR);
+		bcr |= FMC2_BCR_FACCEN;
+		break;
+	case FMC2_ASYNC_MODE_B_NOR:
+		/*
+		 * MUXEN = 0, MTYP = 2, FACCEN = 1, BURSTEN = 0, WAITEN = 0,
+		 * WREN = 1, EXTMOD = 1, CBURSTRW = 0, ACCMOD = 1
+		 */
+		bcr |= FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_NOR);
+		bcr |= FMC2_BCR_FACCEN | FMC2_BCR_EXTMOD;
+		btr |= FIELD_PREP(FMC2_BXTR_ACCMOD, FMC2_BXTR_EXTMOD_B);
+		bwtr |= FIELD_PREP(FMC2_BXTR_ACCMOD, FMC2_BXTR_EXTMOD_B);
+		break;
+	case FMC2_ASYNC_MODE_C_NOR:
+		/*
+		 * MUXEN = 0, MTYP = 2, FACCEN = 1, BURSTEN = 0, WAITEN = 0,
+		 * WREN = 1, EXTMOD = 1, CBURSTRW = 0, ACCMOD = 2
+		 */
+		bcr |= FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_NOR);
+		bcr |= FMC2_BCR_FACCEN | FMC2_BCR_EXTMOD;
+		btr |= FIELD_PREP(FMC2_BXTR_ACCMOD, FMC2_BXTR_EXTMOD_C);
+		bwtr |= FIELD_PREP(FMC2_BXTR_ACCMOD, FMC2_BXTR_EXTMOD_C);
+		break;
+	case FMC2_ASYNC_MODE_D_NOR:
+		/*
+		 * MUXEN = 0, MTYP = 2, FACCEN = 1, BURSTEN = 0, WAITEN = 0,
+		 * WREN = 1, EXTMOD = 1, CBURSTRW = 0, ACCMOD = 3
+		 */
+		bcr |= FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_NOR);
+		bcr |= FMC2_BCR_FACCEN | FMC2_BCR_EXTMOD;
+		btr |= FIELD_PREP(FMC2_BXTR_ACCMOD, FMC2_BXTR_EXTMOD_D);
+		bwtr |= FIELD_PREP(FMC2_BXTR_ACCMOD, FMC2_BXTR_EXTMOD_D);
+		break;
+	case FMC2_SYNC_READ_SYNC_WRITE_PSRAM:
+		/*
+		 * MUXEN = 0, MTYP = 1, FACCEN = 0, BURSTEN = 1, WAITEN = 0,
+		 * WREN = 1, EXTMOD = 0, CBURSTRW = 1, ACCMOD = 0
+		 */
+		bcr |= FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_PSRAM);
+		bcr |= FMC2_BCR_BURSTEN | FMC2_BCR_CBURSTRW;
+		break;
+	case FMC2_SYNC_READ_ASYNC_WRITE_PSRAM:
+		/*
+		 * MUXEN = 0, MTYP = 1, FACCEN = 0, BURSTEN = 1, WAITEN = 0,
+		 * WREN = 1, EXTMOD = 0, CBURSTRW = 0, ACCMOD = 0
+		 */
+		bcr |= FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_PSRAM);
+		bcr |= FMC2_BCR_BURSTEN;
+		break;
+	case FMC2_SYNC_READ_SYNC_WRITE_NOR:
+		/*
+		 * MUXEN = 0, MTYP = 2, FACCEN = 1, BURSTEN = 1, WAITEN = 0,
+		 * WREN = 1, EXTMOD = 0, CBURSTRW = 1, ACCMOD = 0
+		 */
+		bcr |= FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_NOR);
+		bcr |= FMC2_BCR_FACCEN | FMC2_BCR_BURSTEN | FMC2_BCR_CBURSTRW;
+		break;
+	case FMC2_SYNC_READ_ASYNC_WRITE_NOR:
+		/*
+		 * MUXEN = 0, MTYP = 2, FACCEN = 1, BURSTEN = 1, WAITEN = 0,
+		 * WREN = 1, EXTMOD = 0, CBURSTRW = 0, ACCMOD = 0
+		 */
+		bcr |= FIELD_PREP(FMC2_BCR_MTYP, FMC2_BCR_MTYP_NOR);
+		bcr |= FMC2_BCR_FACCEN | FMC2_BCR_BURSTEN;
+		break;
+	default:
+		/* Type of transaction not supported */
+		return -EINVAL;
+	}
+
+	if (bcr & FMC2_BCR_EXTMOD)
+		regmap_update_bits(ebi->regmap, FMC2_BWTR(cs),
+				   bwtr_mask, bwtr);
+	regmap_update_bits(ebi->regmap, FMC2_BTR(cs), btr_mask, btr);
+	regmap_update_bits(ebi->regmap, FMC2_BCR(cs), bcr_mask, bcr);
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_set_buswidth(struct stm32_fmc2_ebi *ebi,
+				       const struct stm32_fmc2_prop *prop,
+				       int cs, u32 setup)
+{
+	u32 val;
+
+	switch (setup) {
+	case FMC2_BUSWIDTH_8:
+		val = FIELD_PREP(FMC2_BCR_MWID, FMC2_BCR_MWID_8);
+		break;
+	case FMC2_BUSWIDTH_16:
+		val = FIELD_PREP(FMC2_BCR_MWID, FMC2_BCR_MWID_16);
+		break;
+	default:
+		/* Buswidth not supported */
+		return -EINVAL;
+	}
+
+	regmap_update_bits(ebi->regmap, FMC2_BCR(cs), FMC2_BCR_MWID, val);
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_set_cpsize(struct stm32_fmc2_ebi *ebi,
+				     const struct stm32_fmc2_prop *prop,
+				     int cs, u32 setup)
+{
+	u32 val;
+
+	switch (setup) {
+	case FMC2_CPSIZE_0:
+		val = FIELD_PREP(FMC2_BCR_CPSIZE, FMC2_BCR_CPSIZE_0);
+		break;
+	case FMC2_CPSIZE_128:
+		val = FIELD_PREP(FMC2_BCR_CPSIZE, FMC2_BCR_CPSIZE_128);
+		break;
+	case FMC2_CPSIZE_256:
+		val = FIELD_PREP(FMC2_BCR_CPSIZE, FMC2_BCR_CPSIZE_256);
+		break;
+	case FMC2_CPSIZE_512:
+		val = FIELD_PREP(FMC2_BCR_CPSIZE, FMC2_BCR_CPSIZE_512);
+		break;
+	case FMC2_CPSIZE_1024:
+		val = FIELD_PREP(FMC2_BCR_CPSIZE, FMC2_BCR_CPSIZE_1024);
+		break;
+	default:
+		/* Cpsize not supported */
+		return -EINVAL;
+	}
+
+	regmap_update_bits(ebi->regmap, FMC2_BCR(cs), FMC2_BCR_CPSIZE, val);
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_set_bl_setup(struct stm32_fmc2_ebi *ebi,
+				       const struct stm32_fmc2_prop *prop,
+				       int cs, u32 setup)
+{
+	u32 val;
+
+	val = min_t(u32, setup, FMC2_BCR_NBLSET_MAX);
+	val = FIELD_PREP(FMC2_BCR_NBLSET, val);
+	regmap_update_bits(ebi->regmap, FMC2_BCR(cs), FMC2_BCR_NBLSET, val);
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_set_address_setup(struct stm32_fmc2_ebi *ebi,
+					    const struct stm32_fmc2_prop *prop,
+					    int cs, u32 setup)
+{
+	u32 bcr, bxtr, reg;
+	u32 val = FIELD_PREP(FMC2_BXTR_ACCMOD, FMC2_BXTR_EXTMOD_D);
+	int ret;
+
+	ret = stm32_fmc2_ebi_get_reg(prop->reg_type, cs, &reg);
+	if (ret)
+		return ret;
+
+	regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+	if (prop->reg_type == FMC2_REG_BWTR)
+		regmap_read(ebi->regmap, FMC2_BWTR(cs), &bxtr);
+	else
+		regmap_read(ebi->regmap, FMC2_BTR(cs), &bxtr);
+
+	if ((bxtr & FMC2_BXTR_ACCMOD) == val || bcr & FMC2_BCR_MUXEN)
+		val = clamp_val(setup, 1, FMC2_BXTR_ADDSET_MAX);
+	else
+		val = min_t(u32, setup, FMC2_BXTR_ADDSET_MAX);
+	val = FIELD_PREP(FMC2_BXTR_ADDSET, val);
+	regmap_update_bits(ebi->regmap, reg, FMC2_BXTR_ADDSET, val);
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_set_address_hold(struct stm32_fmc2_ebi *ebi,
+					   const struct stm32_fmc2_prop *prop,
+					   int cs, u32 setup)
+{
+	u32 val, reg;
+	int ret;
+
+	ret = stm32_fmc2_ebi_get_reg(prop->reg_type, cs, &reg);
+	if (ret)
+		return ret;
+
+	val = clamp_val(setup, 1, FMC2_BXTR_ADDHLD_MAX);
+	val = FIELD_PREP(FMC2_BXTR_ADDHLD, val);
+	regmap_update_bits(ebi->regmap, reg, FMC2_BXTR_ADDHLD, val);
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_set_data_setup(struct stm32_fmc2_ebi *ebi,
+					 const struct stm32_fmc2_prop *prop,
+					 int cs, u32 setup)
+{
+	u32 val, reg;
+	int ret;
+
+	ret = stm32_fmc2_ebi_get_reg(prop->reg_type, cs, &reg);
+	if (ret)
+		return ret;
+
+	val = clamp_val(setup, 1, FMC2_BXTR_DATAST_MAX);
+	val = FIELD_PREP(FMC2_BXTR_DATAST, val);
+	regmap_update_bits(ebi->regmap, reg, FMC2_BXTR_DATAST, val);
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_set_bus_turnaround(struct stm32_fmc2_ebi *ebi,
+					     const struct stm32_fmc2_prop *prop,
+					     int cs, u32 setup)
+{
+	u32 val, reg;
+	int ret;
+
+	ret = stm32_fmc2_ebi_get_reg(prop->reg_type, cs, &reg);
+	if (ret)
+		return ret;
+
+	val = setup ? min_t(u32, setup - 1, FMC2_BXTR_BUSTURN_MAX) : 0;
+	val = FIELD_PREP(FMC2_BXTR_BUSTURN, val);
+	regmap_update_bits(ebi->regmap, reg, FMC2_BXTR_BUSTURN, val);
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_set_data_hold(struct stm32_fmc2_ebi *ebi,
+					const struct stm32_fmc2_prop *prop,
+					int cs, u32 setup)
+{
+	u32 val, reg;
+	int ret;
+
+	ret = stm32_fmc2_ebi_get_reg(prop->reg_type, cs, &reg);
+	if (ret)
+		return ret;
+
+	if (prop->reg_type == FMC2_REG_BWTR)
+		val = setup ? min_t(u32, setup - 1, FMC2_BXTR_DATAHLD_MAX) : 0;
+	else
+		val = min_t(u32, setup, FMC2_BXTR_DATAHLD_MAX);
+	val = FIELD_PREP(FMC2_BXTR_DATAHLD, val);
+	regmap_update_bits(ebi->regmap, reg, FMC2_BXTR_DATAHLD, val);
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_set_clk_period(struct stm32_fmc2_ebi *ebi,
+					 const struct stm32_fmc2_prop *prop,
+					 int cs, u32 setup)
+{
+	u32 val;
+
+	val = setup ? clamp_val(setup - 1, 1, FMC2_BTR_CLKDIV_MAX) : 1;
+	val = FIELD_PREP(FMC2_BTR_CLKDIV, val);
+	regmap_update_bits(ebi->regmap, FMC2_BTR(cs), FMC2_BTR_CLKDIV, val);
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_set_data_latency(struct stm32_fmc2_ebi *ebi,
+					   const struct stm32_fmc2_prop *prop,
+					   int cs, u32 setup)
+{
+	u32 val;
+
+	val = setup > 1 ? min_t(u32, setup - 2, FMC2_BTR_DATLAT_MAX) : 0;
+	val = FIELD_PREP(FMC2_BTR_DATLAT, val);
+	regmap_update_bits(ebi->regmap, FMC2_BTR(cs), FMC2_BTR_DATLAT, val);
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_set_max_low_pulse(struct stm32_fmc2_ebi *ebi,
+					    const struct stm32_fmc2_prop *prop,
+					    int cs, u32 setup)
+{
+	u32 old_val, new_val, pcscntr;
+
+	if (setup < 1)
+		return 0;
+
+	regmap_read(ebi->regmap, FMC2_PCSCNTR, &pcscntr);
+
+	/* Enable counter for the bank */
+	regmap_update_bits(ebi->regmap, FMC2_PCSCNTR,
+			   FMC2_PCSCNTR_CNTBEN(cs),
+			   FMC2_PCSCNTR_CNTBEN(cs));
+
+	new_val = min_t(u32, setup - 1, FMC2_PCSCNTR_CSCOUNT_MAX);
+	old_val = FIELD_GET(FMC2_PCSCNTR_CSCOUNT, pcscntr);
+	if (old_val && new_val > old_val)
+		/* Keep current counter value */
+		return 0;
+
+	new_val = FIELD_PREP(FMC2_PCSCNTR_CSCOUNT, new_val);
+	regmap_update_bits(ebi->regmap, FMC2_PCSCNTR,
+			   FMC2_PCSCNTR_CSCOUNT, new_val);
+
+	return 0;
+}
+
+static const struct stm32_fmc2_prop stm32_fmc2_child_props[] = {
+	/* st,fmc2-ebi-cs-trans-type must be the first property */
+	{
+		.name = "st,fmc2-ebi-cs-transaction-type",
+		.mprop = true,
+		.set = stm32_fmc2_ebi_set_trans_type,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-cclk-enable",
+		.bprop = true,
+		.reg_type = FMC2_REG_BCR,
+		.reg_mask = FMC2_BCR1_CCLKEN,
+		.check = stm32_fmc2_ebi_check_cclk,
+		.set = stm32_fmc2_ebi_set_bit_field,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-mux-enable",
+		.bprop = true,
+		.reg_type = FMC2_REG_BCR,
+		.reg_mask = FMC2_BCR_MUXEN,
+		.check = stm32_fmc2_ebi_check_mux,
+		.set = stm32_fmc2_ebi_set_bit_field,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-buswidth",
+		.reset_val = FMC2_BUSWIDTH_16,
+		.set = stm32_fmc2_ebi_set_buswidth,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-waitpol-high",
+		.bprop = true,
+		.reg_type = FMC2_REG_BCR,
+		.reg_mask = FMC2_BCR_WAITPOL,
+		.set = stm32_fmc2_ebi_set_bit_field,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-waitcfg-enable",
+		.bprop = true,
+		.reg_type = FMC2_REG_BCR,
+		.reg_mask = FMC2_BCR_WAITCFG,
+		.check = stm32_fmc2_ebi_check_waitcfg,
+		.set = stm32_fmc2_ebi_set_bit_field,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-wait-enable",
+		.bprop = true,
+		.reg_type = FMC2_REG_BCR,
+		.reg_mask = FMC2_BCR_WAITEN,
+		.check = stm32_fmc2_ebi_check_sync_trans,
+		.set = stm32_fmc2_ebi_set_bit_field,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-asyncwait-enable",
+		.bprop = true,
+		.reg_type = FMC2_REG_BCR,
+		.reg_mask = FMC2_BCR_ASYNCWAIT,
+		.check = stm32_fmc2_ebi_check_async_trans,
+		.set = stm32_fmc2_ebi_set_bit_field,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-cpsize",
+		.check = stm32_fmc2_ebi_check_cpsize,
+		.set = stm32_fmc2_ebi_set_cpsize,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-byte-lane-setup-ns",
+		.calculate = stm32_fmc2_ebi_ns_to_clock_cycles,
+		.set = stm32_fmc2_ebi_set_bl_setup,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-address-setup-ns",
+		.reg_type = FMC2_REG_BTR,
+		.reset_val = FMC2_BXTR_ADDSET_MAX,
+		.check = stm32_fmc2_ebi_check_async_trans,
+		.calculate = stm32_fmc2_ebi_ns_to_clock_cycles,
+		.set = stm32_fmc2_ebi_set_address_setup,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-address-hold-ns",
+		.reg_type = FMC2_REG_BTR,
+		.reset_val = FMC2_BXTR_ADDHLD_MAX,
+		.check = stm32_fmc2_ebi_check_address_hold,
+		.calculate = stm32_fmc2_ebi_ns_to_clock_cycles,
+		.set = stm32_fmc2_ebi_set_address_hold,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-data-setup-ns",
+		.reg_type = FMC2_REG_BTR,
+		.reset_val = FMC2_BXTR_DATAST_MAX,
+		.check = stm32_fmc2_ebi_check_async_trans,
+		.calculate = stm32_fmc2_ebi_ns_to_clock_cycles,
+		.set = stm32_fmc2_ebi_set_data_setup,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-bus-turnaround-ns",
+		.reg_type = FMC2_REG_BTR,
+		.reset_val = FMC2_BXTR_BUSTURN_MAX + 1,
+		.calculate = stm32_fmc2_ebi_ns_to_clock_cycles,
+		.set = stm32_fmc2_ebi_set_bus_turnaround,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-data-hold-ns",
+		.reg_type = FMC2_REG_BTR,
+		.check = stm32_fmc2_ebi_check_async_trans,
+		.calculate = stm32_fmc2_ebi_ns_to_clock_cycles,
+		.set = stm32_fmc2_ebi_set_data_hold,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-clk-period-ns",
+		.reset_val = FMC2_BTR_CLKDIV_MAX + 1,
+		.check = stm32_fmc2_ebi_check_clk_period,
+		.calculate = stm32_fmc2_ebi_ns_to_clock_cycles,
+		.set = stm32_fmc2_ebi_set_clk_period,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-data-latency-ns",
+		.check = stm32_fmc2_ebi_check_sync_trans,
+		.calculate = stm32_fmc2_ebi_ns_to_clk_period,
+		.set = stm32_fmc2_ebi_set_data_latency,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-write-address-setup-ns",
+		.reg_type = FMC2_REG_BWTR,
+		.reset_val = FMC2_BXTR_ADDSET_MAX,
+		.check = stm32_fmc2_ebi_check_async_trans,
+		.calculate = stm32_fmc2_ebi_ns_to_clock_cycles,
+		.set = stm32_fmc2_ebi_set_address_setup,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-write-address-hold-ns",
+		.reg_type = FMC2_REG_BWTR,
+		.reset_val = FMC2_BXTR_ADDHLD_MAX,
+		.check = stm32_fmc2_ebi_check_address_hold,
+		.calculate = stm32_fmc2_ebi_ns_to_clock_cycles,
+		.set = stm32_fmc2_ebi_set_address_hold,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-write-data-setup-ns",
+		.reg_type = FMC2_REG_BWTR,
+		.reset_val = FMC2_BXTR_DATAST_MAX,
+		.check = stm32_fmc2_ebi_check_async_trans,
+		.calculate = stm32_fmc2_ebi_ns_to_clock_cycles,
+		.set = stm32_fmc2_ebi_set_data_setup,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-write-bus-turnaround-ns",
+		.reg_type = FMC2_REG_BWTR,
+		.reset_val = FMC2_BXTR_BUSTURN_MAX + 1,
+		.calculate = stm32_fmc2_ebi_ns_to_clock_cycles,
+		.set = stm32_fmc2_ebi_set_bus_turnaround,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-write-data-hold-ns",
+		.reg_type = FMC2_REG_BWTR,
+		.check = stm32_fmc2_ebi_check_async_trans,
+		.calculate = stm32_fmc2_ebi_ns_to_clock_cycles,
+		.set = stm32_fmc2_ebi_set_data_hold,
+	},
+	{
+		.name = "st,fmc2-ebi-cs-max-low-pulse-ns",
+		.calculate = stm32_fmc2_ebi_ns_to_clock_cycles,
+		.set = stm32_fmc2_ebi_set_max_low_pulse,
+	},
+};
+
+static int stm32_fmc2_ebi_parse_prop(struct stm32_fmc2_ebi *ebi,
+				     struct device_node *dev_node,
+				     const struct stm32_fmc2_prop *prop,
+				     int cs)
+{
+	struct device *dev = ebi->dev;
+	u32 setup = 0;
+
+	if (!prop->set) {
+		dev_err(dev, "property %s is not well defined\n", prop->name);
+		return -EINVAL;
+	}
+
+	if (prop->check && prop->check(ebi, prop, cs))
+		/* Skeep this property */
+		return 0;
+
+	if (prop->bprop) {
+		bool bprop;
+
+		bprop = of_property_read_bool(dev_node, prop->name);
+		if (prop->mprop && !bprop) {
+			dev_err(dev, "mandatory property %s not defined in the device tree\n",
+				prop->name);
+			return -EINVAL;
+		}
+
+		if (bprop)
+			setup = 1;
+	} else {
+		u32 val;
+		int ret;
+
+		ret = of_property_read_u32(dev_node, prop->name, &val);
+		if (prop->mprop && ret) {
+			dev_err(dev, "mandatory property %s not defined in the device tree\n",
+				prop->name);
+			return ret;
+		}
+
+		if (ret)
+			setup = prop->reset_val;
+		else if (prop->calculate)
+			setup = prop->calculate(ebi, cs, val);
+		else
+			setup = val;
+	}
+
+	return prop->set(ebi, prop, cs, setup);
+}
+
+static void stm32_fmc2_ebi_enable_bank(struct stm32_fmc2_ebi *ebi, int cs)
+{
+	regmap_update_bits(ebi->regmap, FMC2_BCR(cs),
+			   FMC2_BCR_MBKEN, FMC2_BCR_MBKEN);
+}
+
+static void stm32_fmc2_ebi_disable_bank(struct stm32_fmc2_ebi *ebi, int cs)
+{
+	regmap_update_bits(ebi->regmap, FMC2_BCR(cs), FMC2_BCR_MBKEN, 0);
+}
+
+static void stm32_fmc2_ebi_save_setup(struct stm32_fmc2_ebi *ebi)
+{
+	unsigned int cs;
+
+	for (cs = 0; cs < FMC2_MAX_EBI_CE; cs++) {
+		regmap_read(ebi->regmap, FMC2_BCR(cs), &ebi->bcr[cs]);
+		regmap_read(ebi->regmap, FMC2_BTR(cs), &ebi->btr[cs]);
+		regmap_read(ebi->regmap, FMC2_BWTR(cs), &ebi->bwtr[cs]);
+	}
+
+	regmap_read(ebi->regmap, FMC2_PCSCNTR, &ebi->pcscntr);
+}
+
+static void stm32_fmc2_ebi_set_setup(struct stm32_fmc2_ebi *ebi)
+{
+	unsigned int cs;
+
+	for (cs = 0; cs < FMC2_MAX_EBI_CE; cs++) {
+		regmap_write(ebi->regmap, FMC2_BCR(cs), ebi->bcr[cs]);
+		regmap_write(ebi->regmap, FMC2_BTR(cs), ebi->btr[cs]);
+		regmap_write(ebi->regmap, FMC2_BWTR(cs), ebi->bwtr[cs]);
+	}
+
+	regmap_write(ebi->regmap, FMC2_PCSCNTR, ebi->pcscntr);
+}
+
+static void stm32_fmc2_ebi_disable_banks(struct stm32_fmc2_ebi *ebi)
+{
+	unsigned int cs;
+
+	for (cs = 0; cs < FMC2_MAX_EBI_CE; cs++) {
+		if (!(ebi->bank_assigned & BIT(cs)))
+			continue;
+
+		stm32_fmc2_ebi_disable_bank(ebi, cs);
+	}
+}
+
+/* NWAIT signal can not be connected to EBI controller and NAND controller */
+static bool stm32_fmc2_ebi_nwait_used_by_ctrls(struct stm32_fmc2_ebi *ebi)
+{
+	unsigned int cs;
+	u32 bcr;
+
+	for (cs = 0; cs < FMC2_MAX_EBI_CE; cs++) {
+		if (!(ebi->bank_assigned & BIT(cs)))
+			continue;
+
+		regmap_read(ebi->regmap, FMC2_BCR(cs), &bcr);
+		if ((bcr & FMC2_BCR_WAITEN || bcr & FMC2_BCR_ASYNCWAIT) &&
+		    ebi->bank_assigned & BIT(FMC2_NAND))
+			return true;
+	}
+
+	return false;
+}
+
+static void stm32_fmc2_ebi_enable(struct stm32_fmc2_ebi *ebi)
+{
+	regmap_update_bits(ebi->regmap, FMC2_BCR1,
+			   FMC2_BCR1_FMC2EN, FMC2_BCR1_FMC2EN);
+}
+
+static void stm32_fmc2_ebi_disable(struct stm32_fmc2_ebi *ebi)
+{
+	regmap_update_bits(ebi->regmap, FMC2_BCR1, FMC2_BCR1_FMC2EN, 0);
+}
+
+static int stm32_fmc2_ebi_setup_cs(struct stm32_fmc2_ebi *ebi,
+				   struct device_node *dev_node,
+				   u32 cs)
+{
+	unsigned int i;
+	int ret;
+
+	stm32_fmc2_ebi_disable_bank(ebi, cs);
+
+	for (i = 0; i < ARRAY_SIZE(stm32_fmc2_child_props); i++) {
+		const struct stm32_fmc2_prop *p = &stm32_fmc2_child_props[i];
+
+		ret = stm32_fmc2_ebi_parse_prop(ebi, dev_node, p, cs);
+		if (ret) {
+			dev_err(ebi->dev, "property %s could not be set: %d\n",
+				p->name, ret);
+			return ret;
+		}
+	}
+
+	stm32_fmc2_ebi_enable_bank(ebi, cs);
+
+	return 0;
+}
+
+static int stm32_fmc2_ebi_parse_dt(struct stm32_fmc2_ebi *ebi)
+{
+	struct device *dev = ebi->dev;
+	struct device_node *child;
+	bool child_found = false;
+	u32 bank;
+	int ret;
+
+	for_each_available_child_of_node(dev->of_node, child) {
+		ret = of_property_read_u32(child, "reg", &bank);
+		if (ret) {
+			dev_err(dev, "could not retrieve reg property: %d\n",
+				ret);
+			return ret;
+		}
+
+		if (bank >= FMC2_MAX_BANKS) {
+			dev_err(dev, "invalid reg value: %d\n", bank);
+			return -EINVAL;
+		}
+
+		if (ebi->bank_assigned & BIT(bank)) {
+			dev_err(dev, "bank already assigned: %d\n", bank);
+			return -EINVAL;
+		}
+
+		if (bank < FMC2_MAX_EBI_CE) {
+			ret = stm32_fmc2_ebi_setup_cs(ebi, child, bank);
+			if (ret) {
+				dev_err(dev, "setup chip select %d failed: %d\n",
+					bank, ret);
+				return ret;
+			}
+		}
+
+		ebi->bank_assigned |= BIT(bank);
+		child_found = true;
+	}
+
+	if (!child_found) {
+		dev_warn(dev, "no subnodes found, disable the driver.\n");
+		return -ENODEV;
+	}
+
+	if (stm32_fmc2_ebi_nwait_used_by_ctrls(ebi)) {
+		dev_err(dev, "NWAIT signal connected to EBI and NAND controllers\n");
+		return -EINVAL;
+	}
+
+	stm32_fmc2_ebi_enable(ebi);
+
+	return of_platform_populate(dev->of_node, NULL, NULL, dev);
+}
+
+static int stm32_fmc2_ebi_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct stm32_fmc2_ebi *ebi;
+	struct reset_control *rstc;
+	int ret;
+
+	ebi = devm_kzalloc(&pdev->dev, sizeof(*ebi), GFP_KERNEL);
+	if (!ebi)
+		return -ENOMEM;
+
+	ebi->dev = dev;
+
+	ebi->regmap = device_node_to_regmap(dev->of_node);
+	if (IS_ERR(ebi->regmap))
+		return PTR_ERR(ebi->regmap);
+
+	ebi->clk = devm_clk_get(dev, NULL);
+	if (IS_ERR(ebi->clk))
+		return PTR_ERR(ebi->clk);
+
+	rstc = devm_reset_control_get(dev, NULL);
+	if (PTR_ERR(rstc) == -EPROBE_DEFER)
+		return -EPROBE_DEFER;
+
+	ret = clk_prepare_enable(ebi->clk);
+	if (ret)
+		return ret;
+
+	if (!IS_ERR(rstc)) {
+		reset_control_assert(rstc);
+		reset_control_deassert(rstc);
+	}
+
+	ret = stm32_fmc2_ebi_parse_dt(ebi);
+	if (ret)
+		goto err_release;
+
+	stm32_fmc2_ebi_save_setup(ebi);
+	platform_set_drvdata(pdev, ebi);
+
+	return 0;
+
+err_release:
+	stm32_fmc2_ebi_disable_banks(ebi);
+	stm32_fmc2_ebi_disable(ebi);
+	clk_disable_unprepare(ebi->clk);
+
+	return ret;
+}
+
+static int stm32_fmc2_ebi_remove(struct platform_device *pdev)
+{
+	struct stm32_fmc2_ebi *ebi = platform_get_drvdata(pdev);
+
+	of_platform_depopulate(&pdev->dev);
+	stm32_fmc2_ebi_disable_banks(ebi);
+	stm32_fmc2_ebi_disable(ebi);
+	clk_disable_unprepare(ebi->clk);
+
+	return 0;
+}
+
+static int __maybe_unused stm32_fmc2_ebi_suspend(struct device *dev)
+{
+	struct stm32_fmc2_ebi *ebi = dev_get_drvdata(dev);
+
+	stm32_fmc2_ebi_disable(ebi);
+	clk_disable_unprepare(ebi->clk);
+	pinctrl_pm_select_sleep_state(dev);
+
+	return 0;
+}
+
+static int __maybe_unused stm32_fmc2_ebi_resume(struct device *dev)
+{
+	struct stm32_fmc2_ebi *ebi = dev_get_drvdata(dev);
+	int ret;
+
+	pinctrl_pm_select_default_state(dev);
+
+	ret = clk_prepare_enable(ebi->clk);
+	if (ret)
+		return ret;
+
+	stm32_fmc2_ebi_set_setup(ebi);
+	stm32_fmc2_ebi_enable(ebi);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(stm32_fmc2_ebi_pm_ops, stm32_fmc2_ebi_suspend,
+			 stm32_fmc2_ebi_resume);
+
+static const struct of_device_id stm32_fmc2_ebi_match[] = {
+	{.compatible = "st,stm32mp1-fmc2-ebi"},
+	{}
+};
+MODULE_DEVICE_TABLE(of, stm32_fmc2_ebi_match);
+
+static struct platform_driver stm32_fmc2_ebi_driver = {
+	.probe	= stm32_fmc2_ebi_probe,
+	.remove	= stm32_fmc2_ebi_remove,
+	.driver	= {
+		.name = "stm32_fmc2_ebi",
+		.of_match_table = stm32_fmc2_ebi_match,
+		.pm = &stm32_fmc2_ebi_pm_ops,
+	},
+};
+module_platform_driver(stm32_fmc2_ebi_driver);
+
+MODULE_ALIAS("platform:stm32_fmc2_ebi");
+MODULE_AUTHOR("Christophe Kerello <christophe.kerello@st.com>");
+MODULE_DESCRIPTION("STMicroelectronics STM32 FMC2 ebi driver");
+MODULE_LICENSE("GPL v2");
diff --git a/drivers/mtd/chips/Kconfig b/drivers/mtd/chips/Kconfig
index a7e47e068ad9..aef14990e5f7 100644
--- a/drivers/mtd/chips/Kconfig
+++ b/drivers/mtd/chips/Kconfig
@@ -11,7 +11,7 @@ config MTD_CFI
 	  AMD and other flash manufactures that provides a universal method
 	  for probing the capabilities of flash devices. If you wish to
 	  support any device that is CFI-compliant, you need to enable this
-	  option. Visit <http://www.amd.com/products/nvd/overview/cfi.html>
+	  option. Visit <https://www.amd.com/products/nvd/overview/cfi.html>
 	  for more information on CFI.
 
 config MTD_JEDECPROBE
diff --git a/drivers/mtd/hyperbus/hbmc-am654.c b/drivers/mtd/hyperbus/hbmc-am654.c
index f350a0809f88..e0e33f6bf513 100644
--- a/drivers/mtd/hyperbus/hbmc-am654.c
+++ b/drivers/mtd/hyperbus/hbmc-am654.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 //
-// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+// Copyright (C) 2019 Texas Instruments Incorporated - https://www.ti.com/
 // Author: Vignesh Raghavendra <vigneshr@ti.com>
 
 #include <linux/err.h>
diff --git a/drivers/mtd/hyperbus/hyperbus-core.c b/drivers/mtd/hyperbus/hyperbus-core.c
index 32685e8dd278..2f9fc4e17d53 100644
--- a/drivers/mtd/hyperbus/hyperbus-core.c
+++ b/drivers/mtd/hyperbus/hyperbus-core.c
@@ -1,6 +1,6 @@
 // SPDX-License-Identifier: GPL-2.0
 //
-// Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+// Copyright (C) 2019 Texas Instruments Incorporated - https://www.ti.com/
 // Author: Vignesh Raghavendra <vigneshr@ti.com>
 
 #include <linux/err.h>
diff --git a/drivers/mtd/maps/Kconfig b/drivers/mtd/maps/Kconfig
index b28225a7c4f3..fd37553f1b07 100644
--- a/drivers/mtd/maps/Kconfig
+++ b/drivers/mtd/maps/Kconfig
@@ -310,7 +310,7 @@ config MTD_DC21285
 	help
 	  This provides a driver for the flash accessed using Intel's
 	  21285 bridge used with Intel's StrongARM processors. More info at
-	  <http://www.intel.com/design/bridge/docs/21285_documentation.htm>.
+	  <https://www.intel.com/design/bridge/docs/21285_documentation.htm>.
 
 config MTD_IXP4XX
 	tristate "CFI Flash device mapped on Intel IXP4xx based systems"
diff --git a/drivers/mtd/maps/sc520cdp.c b/drivers/mtd/maps/sc520cdp.c
index 9902b37e18b4..8ef7aec634c7 100644
--- a/drivers/mtd/maps/sc520cdp.c
+++ b/drivers/mtd/maps/sc520cdp.c
@@ -6,7 +6,7 @@
  * The SC520CDP is an evaluation board for the Elan SC520 processor available
  * from AMD. It has two banks of 32-bit Flash ROM, each 8 Megabytes in size,
  * and up to 512 KiB of 8-bit DIL Flash ROM.
- * For details see http://www.amd.com/products/epd/desiging/evalboards/18.elansc520/520_cdp_brief/index.html
+ * For details see https://www.amd.com/products/epd/desiging/evalboards/18.elansc520/520_cdp_brief/index.html
  */
 
 #include <linux/module.h>
diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig
index a5d8a211cb8a..c1a45b071165 100644
--- a/drivers/mtd/nand/Kconfig
+++ b/drivers/mtd/nand/Kconfig
@@ -1,7 +1,12 @@
 # SPDX-License-Identifier: GPL-2.0-only
+
+menu "NAND"
+
 config MTD_NAND_CORE
 	tristate
 
 source "drivers/mtd/nand/onenand/Kconfig"
 source "drivers/mtd/nand/raw/Kconfig"
 source "drivers/mtd/nand/spi/Kconfig"
+
+endmenu
diff --git a/drivers/mtd/nand/onenand/Kconfig b/drivers/mtd/nand/onenand/Kconfig
index 572b8fe69abb..1a0e65bc246e 100644
--- a/drivers/mtd/nand/onenand/Kconfig
+++ b/drivers/mtd/nand/onenand/Kconfig
@@ -1,7 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0-only
 menuconfig MTD_ONENAND
 	tristate "OneNAND Device Support"
-	depends on MTD
 	depends on HAS_IOMEM
 	help
 	  This enables support for accessing all type of OneNAND flash
diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
index 113f61052269..1203775023ad 100644
--- a/drivers/mtd/nand/raw/Kconfig
+++ b/drivers/mtd/nand/raw/Kconfig
@@ -12,7 +12,6 @@ config MTD_NAND_ECC_SW_HAMMING_SMC
 
 menuconfig MTD_RAW_NAND
 	tristate "Raw/Parallel NAND Device Support"
-	depends on MTD
 	select MTD_NAND_CORE
 	select MTD_NAND_ECC_SW_HAMMING
 	help
@@ -415,6 +414,7 @@ config MTD_NAND_TEGRA
 config MTD_NAND_STM32_FMC2
 	tristate "Support for NAND controller on STM32MP SoCs"
 	depends on MACH_STM32MP157 || COMPILE_TEST
+	select MFD_SYSCON
 	help
 	  Enables support for NAND Flash chips on SoCs containing the FMC2
 	  NAND controller. This controller is found on STM32MP SoCs.
diff --git a/drivers/mtd/nand/raw/ams-delta.c b/drivers/mtd/nand/raw/ams-delta.c
index 3711e7a0436c..fdba155416d2 100644
--- a/drivers/mtd/nand/raw/ams-delta.c
+++ b/drivers/mtd/nand/raw/ams-delta.c
@@ -191,8 +191,8 @@ static int gpio_nand_exec_op(struct nand_chip *this,
 	return ret;
 }
 
-static int gpio_nand_setup_data_interface(struct nand_chip *this, int csline,
-					  const struct nand_data_interface *cf)
+static int gpio_nand_setup_interface(struct nand_chip *this, int csline,
+				     const struct nand_interface_config *cf)
 {
 	struct gpio_nand *priv = nand_get_controller_data(this);
 	const struct nand_sdr_timings *sdr = nand_get_sdr_timings(cf);
@@ -217,7 +217,7 @@ static int gpio_nand_setup_data_interface(struct nand_chip *this, int csline,
 
 static const struct nand_controller_ops gpio_nand_ops = {
 	.exec_op = gpio_nand_exec_op,
-	.setup_data_interface = gpio_nand_setup_data_interface,
+	.setup_interface = gpio_nand_setup_interface,
 };
 
 /*
diff --git a/drivers/mtd/nand/raw/arasan-nand-controller.c b/drivers/mtd/nand/raw/arasan-nand-controller.c
index 7141dcccba3c..12c643e97c85 100644
--- a/drivers/mtd/nand/raw/arasan-nand-controller.c
+++ b/drivers/mtd/nand/raw/arasan-nand-controller.c
@@ -854,8 +854,8 @@ static int anfc_exec_op(struct nand_chip *chip,
 	return nand_op_parser_exec_op(chip, &anfc_op_parser, op, check_only);
 }
 
-static int anfc_setup_data_interface(struct nand_chip *chip, int target,
-				     const struct nand_data_interface *conf)
+static int anfc_setup_interface(struct nand_chip *chip, int target,
+				const struct nand_interface_config *conf)
 {
 	struct anand *anand = to_anand(chip);
 	struct arasan_nfc *nfc = to_anfc(chip->controller);
@@ -1083,7 +1083,7 @@ static void anfc_detach_chip(struct nand_chip *chip)
 
 static const struct nand_controller_ops anfc_ops = {
 	.exec_op = anfc_exec_op,
-	.setup_data_interface = anfc_setup_data_interface,
+	.setup_interface = anfc_setup_interface,
 	.attach_chip = anfc_attach_chip,
 	.detach_chip = anfc_detach_chip,
 };
diff --git a/drivers/mtd/nand/raw/atmel/nand-controller.c b/drivers/mtd/nand/raw/atmel/nand-controller.c
index 46a3724a788e..c9818f548d07 100644
--- a/drivers/mtd/nand/raw/atmel/nand-controller.c
+++ b/drivers/mtd/nand/raw/atmel/nand-controller.c
@@ -200,8 +200,8 @@ struct atmel_nand_controller_ops {
 	void (*nand_init)(struct atmel_nand_controller *nc,
 			  struct atmel_nand *nand);
 	int (*ecc_init)(struct nand_chip *chip);
-	int (*setup_data_interface)(struct atmel_nand *nand, int csline,
-				    const struct nand_data_interface *conf);
+	int (*setup_interface)(struct atmel_nand *nand, int csline,
+			       const struct nand_interface_config *conf);
 };
 
 struct atmel_nand_controller_caps {
@@ -1168,7 +1168,7 @@ static int atmel_hsmc_nand_ecc_init(struct nand_chip *chip)
 }
 
 static int atmel_smc_nand_prepare_smcconf(struct atmel_nand *nand,
-					const struct nand_data_interface *conf,
+					const struct nand_interface_config *conf,
 					struct atmel_smc_cs_conf *smcconf)
 {
 	u32 ncycles, totalcycles, timeps, mckperiodps;
@@ -1397,9 +1397,9 @@ static int atmel_smc_nand_prepare_smcconf(struct atmel_nand *nand,
 	return 0;
 }
 
-static int atmel_smc_nand_setup_data_interface(struct atmel_nand *nand,
+static int atmel_smc_nand_setup_interface(struct atmel_nand *nand,
 					int csline,
-					const struct nand_data_interface *conf)
+					const struct nand_interface_config *conf)
 {
 	struct atmel_nand_controller *nc;
 	struct atmel_smc_cs_conf smcconf;
@@ -1422,9 +1422,9 @@ static int atmel_smc_nand_setup_data_interface(struct atmel_nand *nand,
 	return 0;
 }
 
-static int atmel_hsmc_nand_setup_data_interface(struct atmel_nand *nand,
+static int atmel_hsmc_nand_setup_interface(struct atmel_nand *nand,
 					int csline,
-					const struct nand_data_interface *conf)
+					const struct nand_interface_config *conf)
 {
 	struct atmel_hsmc_nand_controller *nc;
 	struct atmel_smc_cs_conf smcconf;
@@ -1452,8 +1452,8 @@ static int atmel_hsmc_nand_setup_data_interface(struct atmel_nand *nand,
 	return 0;
 }
 
-static int atmel_nand_setup_data_interface(struct nand_chip *chip, int csline,
-					const struct nand_data_interface *conf)
+static int atmel_nand_setup_interface(struct nand_chip *chip, int csline,
+				      const struct nand_interface_config *conf)
 {
 	struct atmel_nand *nand = to_atmel_nand(chip);
 	struct atmel_nand_controller *nc;
@@ -1464,7 +1464,7 @@ static int atmel_nand_setup_data_interface(struct nand_chip *chip, int csline,
 	    (csline < 0 && csline != NAND_DATA_IFACE_CHECK_ONLY))
 		return -EINVAL;
 
-	return nc->caps->ops->setup_data_interface(nand, csline, conf);
+	return nc->caps->ops->setup_interface(nand, csline, conf);
 }
 
 static void atmel_nand_init(struct atmel_nand_controller *nc,
@@ -1483,7 +1483,7 @@ static void atmel_nand_init(struct atmel_nand_controller *nc,
 	chip->legacy.write_buf = atmel_nand_write_buf;
 	chip->legacy.select_chip = atmel_nand_select_chip;
 
-	if (!nc->mck || !nc->caps->ops->setup_data_interface)
+	if (!nc->mck || !nc->caps->ops->setup_interface)
 		chip->options |= NAND_KEEP_TIMINGS;
 
 	/* Some NANDs require a longer delay than the default one (20us). */
@@ -1956,7 +1956,7 @@ static int atmel_nand_attach_chip(struct nand_chip *chip)
 
 static const struct nand_controller_ops atmel_nand_controller_ops = {
 	.attach_chip = atmel_nand_attach_chip,
-	.setup_data_interface = atmel_nand_setup_data_interface,
+	.setup_interface = atmel_nand_setup_interface,
 };
 
 static int atmel_nand_controller_init(struct atmel_nand_controller *nc,
@@ -2318,7 +2318,7 @@ static const struct atmel_nand_controller_ops atmel_hsmc_nc_ops = {
 	.remove = atmel_hsmc_nand_controller_remove,
 	.ecc_init = atmel_hsmc_nand_ecc_init,
 	.nand_init = atmel_hsmc_nand_init,
-	.setup_data_interface = atmel_hsmc_nand_setup_data_interface,
+	.setup_interface = atmel_hsmc_nand_setup_interface,
 };
 
 static const struct atmel_nand_controller_caps atmel_sama5_nc_caps = {
@@ -2375,10 +2375,10 @@ atmel_smc_nand_controller_remove(struct atmel_nand_controller *nc)
 
 /*
  * The SMC reg layout of at91rm9200 is completely different which prevents us
- * from re-using atmel_smc_nand_setup_data_interface() for the
- * ->setup_data_interface() hook.
+ * from re-using atmel_smc_nand_setup_interface() for the
+ * ->setup_interface() hook.
  * At this point, there's no support for the at91rm9200 SMC IP, so we leave
- * ->setup_data_interface() unassigned.
+ * ->setup_interface() unassigned.
  */
 static const struct atmel_nand_controller_ops at91rm9200_nc_ops = {
 	.probe = atmel_smc_nand_controller_probe,
@@ -2399,7 +2399,7 @@ static const struct atmel_nand_controller_ops atmel_smc_nc_ops = {
 	.remove = atmel_smc_nand_controller_remove,
 	.ecc_init = atmel_nand_ecc_init,
 	.nand_init = atmel_smc_nand_init,
-	.setup_data_interface = atmel_smc_nand_setup_data_interface,
+	.setup_interface = atmel_smc_nand_setup_interface,
 };
 
 static const struct atmel_nand_controller_caps atmel_sam9260_nc_caps = {
diff --git a/drivers/mtd/nand/raw/brcmnand/brcmnand.c b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
index 44068e9eea03..a4033d32a710 100644
--- a/drivers/mtd/nand/raw/brcmnand/brcmnand.c
+++ b/drivers/mtd/nand/raw/brcmnand/brcmnand.c
@@ -1918,6 +1918,22 @@ static int brcmnand_edu_trans(struct brcmnand_host *host, u64 addr, u32 *buf,
 	edu_writel(ctrl, EDU_STOP, 0); /* force stop */
 	edu_readl(ctrl, EDU_STOP);
 
+	if (!ret && edu_cmd == EDU_CMD_READ) {
+		u64 err_addr = 0;
+
+		/*
+		 * check for ECC errors here, subpage ECC errors are
+		 * retained in ECC error address register
+		 */
+		err_addr = brcmnand_get_uncorrecc_addr(ctrl);
+		if (!err_addr) {
+			err_addr = brcmnand_get_correcc_addr(ctrl);
+			if (err_addr)
+				ret = -EUCLEAN;
+		} else
+			ret = -EBADMSG;
+	}
+
 	return ret;
 }
 
@@ -2124,6 +2140,7 @@ static int brcmnand_read(struct mtd_info *mtd, struct nand_chip *chip,
 	u64 err_addr = 0;
 	int err;
 	bool retry = true;
+	bool edu_err = false;
 
 	dev_dbg(ctrl->dev, "read %llx -> %p\n", (unsigned long long)addr, buf);
 
@@ -2141,6 +2158,10 @@ try_dmaread:
 			else
 				return -EIO;
 		}
+
+		if (has_edu(ctrl) && err_addr)
+			edu_err = true;
+
 	} else {
 		if (oob)
 			memset(oob, 0x99, mtd->oobsize);
@@ -2188,6 +2209,11 @@ try_dmaread:
 	if (mtd_is_bitflip(err)) {
 		unsigned int corrected = brcmnand_count_corrected(ctrl);
 
+		/* in case of EDU correctable error we read again using PIO */
+		if (edu_err)
+			err = brcmnand_read_by_pio(mtd, chip, addr, trans, buf,
+						   oob, &err_addr);
+
 		dev_dbg(ctrl->dev, "corrected error at 0x%llx\n",
 			(unsigned long long)err_addr);
 		mtd->ecc_stats.corrected += corrected;
@@ -3023,8 +3049,9 @@ int brcmnand_probe(struct platform_device *pdev, struct brcmnand_soc *soc)
 		if (ret < 0)
 			goto err;
 
-		/* set edu transfer function to call */
-		ctrl->dma_trans = brcmnand_edu_trans;
+		if (has_edu(ctrl))
+			/* set edu transfer function to call */
+			ctrl->dma_trans = brcmnand_edu_trans;
 	}
 
 	/* Disable automatic device ID config, direct addressing */
diff --git a/drivers/mtd/nand/raw/cadence-nand-controller.c b/drivers/mtd/nand/raw/cadence-nand-controller.c
index c4f273e2fe78..71516af85f23 100644
--- a/drivers/mtd/nand/raw/cadence-nand-controller.c
+++ b/drivers/mtd/nand/raw/cadence-nand-controller.c
@@ -2304,8 +2304,8 @@ static inline u32 calc_tdvw(u32 trp_cnt, u32 clk_period, u32 trhoh_min,
 }
 
 static int
-cadence_nand_setup_data_interface(struct nand_chip *chip, int chipnr,
-				  const struct nand_data_interface *conf)
+cadence_nand_setup_interface(struct nand_chip *chip, int chipnr,
+			     const struct nand_interface_config *conf)
 {
 	const struct nand_sdr_timings *sdr;
 	struct cdns_nand_ctrl *cdns_ctrl = to_cdns_nand_ctrl(chip->controller);
@@ -2691,7 +2691,7 @@ static int cadence_nand_attach_chip(struct nand_chip *chip)
 static const struct nand_controller_ops cadence_nand_controller_ops = {
 	.attach_chip = cadence_nand_attach_chip,
 	.exec_op = cadence_nand_exec_op,
-	.setup_data_interface = cadence_nand_setup_data_interface,
+	.setup_interface = cadence_nand_setup_interface,
 };
 
 static int cadence_nand_chip_init(struct cdns_nand_ctrl *cdns_ctrl,
diff --git a/drivers/mtd/nand/raw/denali.c b/drivers/mtd/nand/raw/denali.c
index 4e6e1578aa2d..9d99dade95ce 100644
--- a/drivers/mtd/nand/raw/denali.c
+++ b/drivers/mtd/nand/raw/denali.c
@@ -761,8 +761,8 @@ static int denali_write_page(struct nand_chip *chip, const u8 *buf,
 	return denali_page_xfer(chip, (void *)buf, mtd->writesize, page, true);
 }
 
-static int denali_setup_data_interface(struct nand_chip *chip, int chipnr,
-				       const struct nand_data_interface *conf)
+static int denali_setup_interface(struct nand_chip *chip, int chipnr,
+				  const struct nand_interface_config *conf)
 {
 	static const unsigned int data_setup_on_host = 10000;
 	struct denali_controller *denali = to_denali_controller(chip);
@@ -1173,7 +1173,7 @@ static int denali_exec_op(struct nand_chip *chip,
 static const struct nand_controller_ops denali_controller_ops = {
 	.attach_chip = denali_attach_chip,
 	.exec_op = denali_exec_op,
-	.setup_data_interface = denali_setup_data_interface,
+	.setup_interface = denali_setup_interface,
 };
 
 int denali_chip_init(struct denali_controller *denali,
@@ -1230,7 +1230,7 @@ int denali_chip_init(struct denali_controller *denali,
 		chip->buf_align = 16;
 	}
 
-	/* clk rate info is needed for setup_data_interface */
+	/* clk rate info is needed for setup_interface */
 	if (!denali->clk_rate || !denali->clk_x_rate)
 		chip->options |= NAND_KEEP_TIMINGS;
 
diff --git a/drivers/mtd/nand/raw/fsl_upm.c b/drivers/mtd/nand/raw/fsl_upm.c
index 627deb26db51..197850aeb261 100644
--- a/drivers/mtd/nand/raw/fsl_upm.c
+++ b/drivers/mtd/nand/raw/fsl_upm.c
@@ -14,32 +14,23 @@
 #include <linux/mtd/nand_ecc.h>
 #include <linux/mtd/partitions.h>
 #include <linux/mtd/mtd.h>
-#include <linux/of_address.h>
 #include <linux/of_platform.h>
-#include <linux/of_gpio.h>
 #include <linux/io.h>
 #include <linux/slab.h>
 #include <asm/fsl_lbc.h>
 
-#define FSL_UPM_WAIT_RUN_PATTERN  0x1
-#define FSL_UPM_WAIT_WRITE_BYTE   0x2
-#define FSL_UPM_WAIT_WRITE_BUFFER 0x4
-
 struct fsl_upm_nand {
+	struct nand_controller base;
 	struct device *dev;
 	struct nand_chip chip;
-	int last_ctrl;
-	struct mtd_partition *parts;
 	struct fsl_upm upm;
 	uint8_t upm_addr_offset;
 	uint8_t upm_cmd_offset;
 	void __iomem *io_base;
-	int rnb_gpio[NAND_MAX_CHIPS];
+	struct gpio_desc *rnb_gpio[NAND_MAX_CHIPS];
 	uint32_t mchip_offsets[NAND_MAX_CHIPS];
 	uint32_t mchip_count;
 	uint32_t mchip_number;
-	int chip_delay;
-	uint32_t wait_flags;
 };
 
 static inline struct fsl_upm_nand *to_fsl_upm_nand(struct mtd_info *mtdinfo)
@@ -48,106 +39,6 @@ static inline struct fsl_upm_nand *to_fsl_upm_nand(struct mtd_info *mtdinfo)
 			    chip);
 }
 
-static int fun_chip_ready(struct nand_chip *chip)
-{
-	struct fsl_upm_nand *fun = to_fsl_upm_nand(nand_to_mtd(chip));
-
-	if (gpio_get_value(fun->rnb_gpio[fun->mchip_number]))
-		return 1;
-
-	dev_vdbg(fun->dev, "busy\n");
-	return 0;
-}
-
-static void fun_wait_rnb(struct fsl_upm_nand *fun)
-{
-	if (fun->rnb_gpio[fun->mchip_number] >= 0) {
-		struct mtd_info *mtd = nand_to_mtd(&fun->chip);
-		int cnt = 1000000;
-
-		while (--cnt && !fun_chip_ready(&fun->chip))
-			cpu_relax();
-		if (!cnt)
-			dev_err(fun->dev, "tired waiting for RNB\n");
-	} else {
-		ndelay(100);
-	}
-}
-
-static void fun_cmd_ctrl(struct nand_chip *chip, int cmd, unsigned int ctrl)
-{
-	struct fsl_upm_nand *fun = to_fsl_upm_nand(nand_to_mtd(chip));
-	u32 mar;
-
-	if (!(ctrl & fun->last_ctrl)) {
-		fsl_upm_end_pattern(&fun->upm);
-
-		if (cmd == NAND_CMD_NONE)
-			return;
-
-		fun->last_ctrl = ctrl & (NAND_ALE | NAND_CLE);
-	}
-
-	if (ctrl & NAND_CTRL_CHANGE) {
-		if (ctrl & NAND_ALE)
-			fsl_upm_start_pattern(&fun->upm, fun->upm_addr_offset);
-		else if (ctrl & NAND_CLE)
-			fsl_upm_start_pattern(&fun->upm, fun->upm_cmd_offset);
-	}
-
-	mar = (cmd << (32 - fun->upm.width)) |
-		fun->mchip_offsets[fun->mchip_number];
-	fsl_upm_run_pattern(&fun->upm, chip->legacy.IO_ADDR_R, mar);
-
-	if (fun->wait_flags & FSL_UPM_WAIT_RUN_PATTERN)
-		fun_wait_rnb(fun);
-}
-
-static void fun_select_chip(struct nand_chip *chip, int mchip_nr)
-{
-	struct fsl_upm_nand *fun = to_fsl_upm_nand(nand_to_mtd(chip));
-
-	if (mchip_nr == -1) {
-		chip->legacy.cmd_ctrl(chip, NAND_CMD_NONE, 0 | NAND_CTRL_CHANGE);
-	} else if (mchip_nr >= 0 && mchip_nr < NAND_MAX_CHIPS) {
-		fun->mchip_number = mchip_nr;
-		chip->legacy.IO_ADDR_R = fun->io_base + fun->mchip_offsets[mchip_nr];
-		chip->legacy.IO_ADDR_W = chip->legacy.IO_ADDR_R;
-	} else {
-		BUG();
-	}
-}
-
-static uint8_t fun_read_byte(struct nand_chip *chip)
-{
-	struct fsl_upm_nand *fun = to_fsl_upm_nand(nand_to_mtd(chip));
-
-	return in_8(fun->chip.legacy.IO_ADDR_R);
-}
-
-static void fun_read_buf(struct nand_chip *chip, uint8_t *buf, int len)
-{
-	struct fsl_upm_nand *fun = to_fsl_upm_nand(nand_to_mtd(chip));
-	int i;
-
-	for (i = 0; i < len; i++)
-		buf[i] = in_8(fun->chip.legacy.IO_ADDR_R);
-}
-
-static void fun_write_buf(struct nand_chip *chip, const uint8_t *buf, int len)
-{
-	struct fsl_upm_nand *fun = to_fsl_upm_nand(nand_to_mtd(chip));
-	int i;
-
-	for (i = 0; i < len; i++) {
-		out_8(fun->chip.legacy.IO_ADDR_W, buf[i]);
-		if (fun->wait_flags & FSL_UPM_WAIT_WRITE_BYTE)
-			fun_wait_rnb(fun);
-	}
-	if (fun->wait_flags & FSL_UPM_WAIT_WRITE_BUFFER)
-		fun_wait_rnb(fun);
-}
-
 static int fun_chip_init(struct fsl_upm_nand *fun,
 			 const struct device_node *upm_np,
 			 const struct resource *io_res)
@@ -156,21 +47,9 @@ static int fun_chip_init(struct fsl_upm_nand *fun,
 	int ret;
 	struct device_node *flash_np;
 
-	fun->chip.legacy.IO_ADDR_R = fun->io_base;
-	fun->chip.legacy.IO_ADDR_W = fun->io_base;
-	fun->chip.legacy.cmd_ctrl = fun_cmd_ctrl;
-	fun->chip.legacy.chip_delay = fun->chip_delay;
-	fun->chip.legacy.read_byte = fun_read_byte;
-	fun->chip.legacy.read_buf = fun_read_buf;
-	fun->chip.legacy.write_buf = fun_write_buf;
 	fun->chip.ecc.mode = NAND_ECC_SOFT;
 	fun->chip.ecc.algo = NAND_ECC_HAMMING;
-	if (fun->mchip_count > 1)
-		fun->chip.legacy.select_chip = fun_select_chip;
-
-	if (fun->rnb_gpio[0] >= 0)
-		fun->chip.legacy.dev_ready = fun_chip_ready;
-
+	fun->chip.controller = &fun->base;
 	mtd->dev.parent = fun->dev;
 
 	flash_np = of_get_next_child(upm_np, NULL);
@@ -178,8 +57,9 @@ static int fun_chip_init(struct fsl_upm_nand *fun,
 		return -ENODEV;
 
 	nand_set_flash_node(&fun->chip, flash_np);
-	mtd->name = kasprintf(GFP_KERNEL, "0x%llx.%pOFn", (u64)io_res->start,
-			      flash_np);
+	mtd->name = devm_kasprintf(fun->dev, GFP_KERNEL, "0x%llx.%pOFn",
+				   (u64)io_res->start,
+				   flash_np);
 	if (!mtd->name) {
 		ret = -ENOMEM;
 		goto err;
@@ -192,51 +72,130 @@ static int fun_chip_init(struct fsl_upm_nand *fun,
 	ret = mtd_device_register(mtd, NULL, 0);
 err:
 	of_node_put(flash_np);
-	if (ret)
-		kfree(mtd->name);
 	return ret;
 }
 
+static int func_exec_instr(struct nand_chip *chip,
+			   const struct nand_op_instr *instr)
+{
+	struct fsl_upm_nand *fun = to_fsl_upm_nand(nand_to_mtd(chip));
+	u32 mar, reg_offs = fun->mchip_offsets[fun->mchip_number];
+	unsigned int i;
+	const u8 *out;
+	u8 *in;
+
+	switch (instr->type) {
+	case NAND_OP_CMD_INSTR:
+		fsl_upm_start_pattern(&fun->upm, fun->upm_cmd_offset);
+		mar = (instr->ctx.cmd.opcode << (32 - fun->upm.width)) |
+		      reg_offs;
+		fsl_upm_run_pattern(&fun->upm, fun->io_base + reg_offs, mar);
+		fsl_upm_end_pattern(&fun->upm);
+		return 0;
+
+	case NAND_OP_ADDR_INSTR:
+		fsl_upm_start_pattern(&fun->upm, fun->upm_addr_offset);
+		for (i = 0; i < instr->ctx.addr.naddrs; i++) {
+			mar = (instr->ctx.addr.addrs[i] << (32 - fun->upm.width)) |
+			      reg_offs;
+			fsl_upm_run_pattern(&fun->upm, fun->io_base + reg_offs, mar);
+		}
+		fsl_upm_end_pattern(&fun->upm);
+		return 0;
+
+	case NAND_OP_DATA_IN_INSTR:
+		in = instr->ctx.data.buf.in;
+		for (i = 0; i < instr->ctx.data.len; i++)
+			in[i] = in_8(fun->io_base + reg_offs);
+		return 0;
+
+	case NAND_OP_DATA_OUT_INSTR:
+		out = instr->ctx.data.buf.out;
+		for (i = 0; i < instr->ctx.data.len; i++)
+			out_8(fun->io_base + reg_offs, out[i]);
+		return 0;
+
+	case NAND_OP_WAITRDY_INSTR:
+		if (!fun->rnb_gpio[fun->mchip_number])
+			return nand_soft_waitrdy(chip, instr->ctx.waitrdy.timeout_ms);
+
+		return nand_gpio_waitrdy(chip, fun->rnb_gpio[fun->mchip_number],
+					 instr->ctx.waitrdy.timeout_ms);
+
+	default:
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static int fun_exec_op(struct nand_chip *chip, const struct nand_operation *op,
+		       bool check_only)
+{
+	struct fsl_upm_nand *fun = to_fsl_upm_nand(nand_to_mtd(chip));
+	unsigned int i;
+	int ret;
+
+	if (op->cs > NAND_MAX_CHIPS)
+		return -EINVAL;
+
+	if (check_only)
+		return 0;
+
+	fun->mchip_number = op->cs;
+
+	for (i = 0; i < op->ninstrs; i++) {
+		ret = func_exec_instr(chip, &op->instrs[i]);
+		if (ret)
+			return ret;
+
+		if (op->instrs[i].delay_ns)
+			ndelay(op->instrs[i].delay_ns);
+	}
+
+	return 0;
+}
+
+static const struct nand_controller_ops fun_ops = {
+	.exec_op = fun_exec_op,
+};
+
 static int fun_probe(struct platform_device *ofdev)
 {
 	struct fsl_upm_nand *fun;
-	struct resource io_res;
+	struct resource *io_res;
 	const __be32 *prop;
-	int rnb_gpio;
 	int ret;
 	int size;
 	int i;
 
-	fun = kzalloc(sizeof(*fun), GFP_KERNEL);
+	fun = devm_kzalloc(&ofdev->dev, sizeof(*fun), GFP_KERNEL);
 	if (!fun)
 		return -ENOMEM;
 
-	ret = of_address_to_resource(ofdev->dev.of_node, 0, &io_res);
-	if (ret) {
-		dev_err(&ofdev->dev, "can't get IO base\n");
-		goto err1;
-	}
+	io_res = platform_get_resource(ofdev, IORESOURCE_MEM, 0);
+	fun->io_base = devm_ioremap_resource(&ofdev->dev, io_res);
+	if (IS_ERR(fun->io_base))
+		return PTR_ERR(fun->io_base);
 
-	ret = fsl_upm_find(io_res.start, &fun->upm);
+	ret = fsl_upm_find(io_res->start, &fun->upm);
 	if (ret) {
 		dev_err(&ofdev->dev, "can't find UPM\n");
-		goto err1;
+		return ret;
 	}
 
 	prop = of_get_property(ofdev->dev.of_node, "fsl,upm-addr-offset",
 			       &size);
 	if (!prop || size != sizeof(uint32_t)) {
 		dev_err(&ofdev->dev, "can't get UPM address offset\n");
-		ret = -EINVAL;
-		goto err1;
+		return -EINVAL;
 	}
 	fun->upm_addr_offset = *prop;
 
 	prop = of_get_property(ofdev->dev.of_node, "fsl,upm-cmd-offset", &size);
 	if (!prop || size != sizeof(uint32_t)) {
 		dev_err(&ofdev->dev, "can't get UPM command offset\n");
-		ret = -EINVAL;
-		goto err1;
+		return -EINVAL;
 	}
 	fun->upm_cmd_offset = *prop;
 
@@ -246,7 +205,7 @@ static int fun_probe(struct platform_device *ofdev)
 		fun->mchip_count = size / sizeof(uint32_t);
 		if (fun->mchip_count >= NAND_MAX_CHIPS) {
 			dev_err(&ofdev->dev, "too much multiple chips\n");
-			goto err1;
+			return -EINVAL;
 		}
 		for (i = 0; i < fun->mchip_count; i++)
 			fun->mchip_offsets[i] = be32_to_cpu(prop[i]);
@@ -255,63 +214,26 @@ static int fun_probe(struct platform_device *ofdev)
 	}
 
 	for (i = 0; i < fun->mchip_count; i++) {
-		fun->rnb_gpio[i] = -1;
-		rnb_gpio = of_get_gpio(ofdev->dev.of_node, i);
-		if (rnb_gpio >= 0) {
-			ret = gpio_request(rnb_gpio, dev_name(&ofdev->dev));
-			if (ret) {
-				dev_err(&ofdev->dev,
-					"can't request RNB gpio #%d\n", i);
-				goto err2;
-			}
-			gpio_direction_input(rnb_gpio);
-			fun->rnb_gpio[i] = rnb_gpio;
-		} else if (rnb_gpio == -EINVAL) {
+		fun->rnb_gpio[i] = devm_gpiod_get_index_optional(&ofdev->dev,
+								 NULL, i,
+								 GPIOD_IN);
+		if (IS_ERR(fun->rnb_gpio[i])) {
 			dev_err(&ofdev->dev, "RNB gpio #%d is invalid\n", i);
-			goto err2;
+			return PTR_ERR(fun->rnb_gpio[i]);
 		}
 	}
 
-	prop = of_get_property(ofdev->dev.of_node, "chip-delay", NULL);
-	if (prop)
-		fun->chip_delay = be32_to_cpup(prop);
-	else
-		fun->chip_delay = 50;
-
-	prop = of_get_property(ofdev->dev.of_node, "fsl,upm-wait-flags", &size);
-	if (prop && size == sizeof(uint32_t))
-		fun->wait_flags = be32_to_cpup(prop);
-	else
-		fun->wait_flags = FSL_UPM_WAIT_RUN_PATTERN |
-				  FSL_UPM_WAIT_WRITE_BYTE;
-
-	fun->io_base = devm_ioremap(&ofdev->dev, io_res.start,
-					    resource_size(&io_res));
-	if (!fun->io_base) {
-		ret = -ENOMEM;
-		goto err2;
-	}
-
+	nand_controller_init(&fun->base);
+	fun->base.ops = &fun_ops;
 	fun->dev = &ofdev->dev;
-	fun->last_ctrl = NAND_CLE;
 
-	ret = fun_chip_init(fun, ofdev->dev.of_node, &io_res);
+	ret = fun_chip_init(fun, ofdev->dev.of_node, io_res);
 	if (ret)
-		goto err2;
+		return ret;
 
 	dev_set_drvdata(&ofdev->dev, fun);
 
 	return 0;
-err2:
-	for (i = 0; i < fun->mchip_count; i++) {
-		if (fun->rnb_gpio[i] < 0)
-			break;
-		gpio_free(fun->rnb_gpio[i]);
-	}
-err1:
-	kfree(fun);
-
-	return ret;
 }
 
 static int fun_remove(struct platform_device *ofdev)
@@ -319,20 +241,11 @@ static int fun_remove(struct platform_device *ofdev)
 	struct fsl_upm_nand *fun = dev_get_drvdata(&ofdev->dev);
 	struct nand_chip *chip = &fun->chip;
 	struct mtd_info *mtd = nand_to_mtd(chip);
-	int ret, i;
+	int ret;
 
 	ret = mtd_device_unregister(mtd);
 	WARN_ON(ret);
 	nand_cleanup(chip);
-	kfree(mtd->name);
-
-	for (i = 0; i < fun->mchip_count; i++) {
-		if (fun->rnb_gpio[i] < 0)
-			break;
-		gpio_free(fun->rnb_gpio[i]);
-	}
-
-	kfree(fun);
 
 	return 0;
 }
diff --git a/drivers/mtd/nand/raw/fsmc_nand.c b/drivers/mtd/nand/raw/fsmc_nand.c
index 3909752b14c5..92ddc41d0ff0 100644
--- a/drivers/mtd/nand/raw/fsmc_nand.c
+++ b/drivers/mtd/nand/raw/fsmc_nand.c
@@ -327,8 +327,8 @@ static int fsmc_calc_timings(struct fsmc_nand_data *host,
 	return 0;
 }
 
-static int fsmc_setup_data_interface(struct nand_chip *nand, int csline,
-				     const struct nand_data_interface *conf)
+static int fsmc_setup_interface(struct nand_chip *nand, int csline,
+				const struct nand_interface_config *conf)
 {
 	struct fsmc_nand_data *host = nand_to_fsmc(nand);
 	struct fsmc_nand_timings tims;
@@ -951,7 +951,7 @@ static int fsmc_nand_attach_chip(struct nand_chip *nand)
 static const struct nand_controller_ops fsmc_nand_controller_ops = {
 	.attach_chip = fsmc_nand_attach_chip,
 	.exec_op = fsmc_exec_op,
-	.setup_data_interface = fsmc_setup_data_interface,
+	.setup_interface = fsmc_setup_interface,
 };
 
 /**
diff --git a/drivers/mtd/nand/raw/gpio.c b/drivers/mtd/nand/raw/gpio.c
index 938077e5c6a9..3bd847ccc3f3 100644
--- a/drivers/mtd/nand/raw/gpio.c
+++ b/drivers/mtd/nand/raw/gpio.c
@@ -25,8 +25,11 @@
 #include <linux/mtd/nand-gpio.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
+#include <linux/delay.h>
 
 struct gpiomtd {
+	struct nand_controller	base;
+	void __iomem		*io;
 	void __iomem		*io_sync;
 	struct nand_chip	nand_chip;
 	struct gpio_nand_platdata plat;
@@ -69,34 +72,99 @@ static void gpio_nand_dosync(struct gpiomtd *gpiomtd)
 static inline void gpio_nand_dosync(struct gpiomtd *gpiomtd) {}
 #endif
 
-static void gpio_nand_cmd_ctrl(struct nand_chip *chip, int cmd,
-			       unsigned int ctrl)
+static int gpio_nand_exec_instr(struct nand_chip *chip,
+				const struct nand_op_instr *instr)
 {
 	struct gpiomtd *gpiomtd = gpio_nand_getpriv(nand_to_mtd(chip));
+	unsigned int i;
 
-	gpio_nand_dosync(gpiomtd);
+	switch (instr->type) {
+	case NAND_OP_CMD_INSTR:
+		gpio_nand_dosync(gpiomtd);
+		gpiod_set_value(gpiomtd->cle, 1);
+		gpio_nand_dosync(gpiomtd);
+		writeb(instr->ctx.cmd.opcode, gpiomtd->io);
+		gpio_nand_dosync(gpiomtd);
+		gpiod_set_value(gpiomtd->cle, 0);
+		return 0;
+
+	case NAND_OP_ADDR_INSTR:
+		gpio_nand_dosync(gpiomtd);
+		gpiod_set_value(gpiomtd->ale, 1);
+		gpio_nand_dosync(gpiomtd);
+		for (i = 0; i < instr->ctx.addr.naddrs; i++)
+			writeb(instr->ctx.addr.addrs[i], gpiomtd->io);
+		gpio_nand_dosync(gpiomtd);
+		gpiod_set_value(gpiomtd->ale, 0);
+		return 0;
+
+	case NAND_OP_DATA_IN_INSTR:
+		gpio_nand_dosync(gpiomtd);
+		if ((chip->options & NAND_BUSWIDTH_16) &&
+		    !instr->ctx.data.force_8bit)
+			ioread16_rep(gpiomtd->io, instr->ctx.data.buf.in,
+				     instr->ctx.data.len / 2);
+		else
+			ioread8_rep(gpiomtd->io, instr->ctx.data.buf.in,
+				    instr->ctx.data.len);
+		return 0;
 
-	if (ctrl & NAND_CTRL_CHANGE) {
-		if (gpiomtd->nce)
-			gpiod_set_value(gpiomtd->nce, !(ctrl & NAND_NCE));
-		gpiod_set_value(gpiomtd->cle, !!(ctrl & NAND_CLE));
-		gpiod_set_value(gpiomtd->ale, !!(ctrl & NAND_ALE));
+	case NAND_OP_DATA_OUT_INSTR:
 		gpio_nand_dosync(gpiomtd);
+		if ((chip->options & NAND_BUSWIDTH_16) &&
+		    !instr->ctx.data.force_8bit)
+			iowrite16_rep(gpiomtd->io, instr->ctx.data.buf.out,
+				      instr->ctx.data.len / 2);
+		else
+			iowrite8_rep(gpiomtd->io, instr->ctx.data.buf.out,
+				     instr->ctx.data.len);
+		return 0;
+
+	case NAND_OP_WAITRDY_INSTR:
+		if (!gpiomtd->rdy)
+			return nand_soft_waitrdy(chip, instr->ctx.waitrdy.timeout_ms);
+
+		return nand_gpio_waitrdy(chip, gpiomtd->rdy,
+					 instr->ctx.waitrdy.timeout_ms);
+
+	default:
+		return -EINVAL;
 	}
-	if (cmd == NAND_CMD_NONE)
-		return;
 
-	writeb(cmd, gpiomtd->nand_chip.legacy.IO_ADDR_W);
-	gpio_nand_dosync(gpiomtd);
+	return 0;
 }
 
-static int gpio_nand_devready(struct nand_chip *chip)
+static int gpio_nand_exec_op(struct nand_chip *chip,
+			     const struct nand_operation *op,
+			     bool check_only)
 {
 	struct gpiomtd *gpiomtd = gpio_nand_getpriv(nand_to_mtd(chip));
+	unsigned int i;
+	int ret = 0;
+
+	if (check_only)
+		return 0;
 
-	return gpiod_get_value(gpiomtd->rdy);
+	gpio_nand_dosync(gpiomtd);
+	gpiod_set_value(gpiomtd->nce, 0);
+	for (i = 0; i < op->ninstrs; i++) {
+		ret = gpio_nand_exec_instr(chip, &op->instrs[i]);
+		if (ret)
+			break;
+
+		if (op->instrs[i].delay_ns)
+			ndelay(op->instrs[i].delay_ns);
+	}
+	gpio_nand_dosync(gpiomtd);
+	gpiod_set_value(gpiomtd->nce, 1);
+
+	return ret;
 }
 
+static const struct nand_controller_ops gpio_nand_ops = {
+	.exec_op = gpio_nand_exec_op,
+};
+
 #ifdef CONFIG_OF
 static const struct of_device_id gpio_nand_id_table[] = {
 	{ .compatible = "gpio-control-nand" },
@@ -225,9 +293,9 @@ static int gpio_nand_probe(struct platform_device *pdev)
 	chip = &gpiomtd->nand_chip;
 
 	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	chip->legacy.IO_ADDR_R = devm_ioremap_resource(dev, res);
-	if (IS_ERR(chip->legacy.IO_ADDR_R))
-		return PTR_ERR(chip->legacy.IO_ADDR_R);
+	gpiomtd->io = devm_ioremap_resource(dev, res);
+	if (IS_ERR(gpiomtd->io))
+		return PTR_ERR(gpiomtd->io);
 
 	res = gpio_nand_get_io_sync(pdev);
 	if (res) {
@@ -269,17 +337,15 @@ static int gpio_nand_probe(struct platform_device *pdev)
 		ret = PTR_ERR(gpiomtd->rdy);
 		goto out_ce;
 	}
-	/* Using RDY pin */
-	if (gpiomtd->rdy)
-		chip->legacy.dev_ready = gpio_nand_devready;
+
+	nand_controller_init(&gpiomtd->base);
+	gpiomtd->base.ops = &gpio_nand_ops;
 
 	nand_set_flash_node(chip, pdev->dev.of_node);
-	chip->legacy.IO_ADDR_W	= chip->legacy.IO_ADDR_R;
 	chip->ecc.mode		= NAND_ECC_SOFT;
 	chip->ecc.algo		= NAND_ECC_HAMMING;
 	chip->options		= gpiomtd->plat.options;
-	chip->legacy.chip_delay	= gpiomtd->plat.chip_delay;
-	chip->legacy.cmd_ctrl	= gpio_nand_cmd_ctrl;
+	chip->controller	= &gpiomtd->base;
 
 	mtd			= nand_to_mtd(chip);
 	mtd->dev.parent		= dev;
diff --git a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
index 061a8ddda275..5d4aee46cc55 100644
--- a/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
+++ b/drivers/mtd/nand/raw/gpmi-nand/gpmi-nand.c
@@ -736,8 +736,8 @@ static void gpmi_nfc_apply_timings(struct gpmi_nand_data *this)
 	udelay(dll_wait_time_us);
 }
 
-static int gpmi_setup_data_interface(struct nand_chip *chip, int chipnr,
-				     const struct nand_data_interface *conf)
+static int gpmi_setup_interface(struct nand_chip *chip, int chipnr,
+				const struct nand_interface_config *conf)
 {
 	struct gpmi_nand_data *this = nand_get_controller_data(chip);
 	const struct nand_sdr_timings *sdr;
@@ -2400,7 +2400,7 @@ unmap:
 
 static const struct nand_controller_ops gpmi_nand_controller_ops = {
 	.attach_chip = gpmi_nand_attach_chip,
-	.setup_data_interface = gpmi_setup_data_interface,
+	.setup_interface = gpmi_setup_interface,
 	.exec_op = gpmi_nfc_exec_op,
 };
 
diff --git a/drivers/mtd/nand/raw/ingenic/jz4740_ecc.c b/drivers/mtd/nand/raw/ingenic/jz4740_ecc.c
index 13fea645c7f0..54e377754a6c 100644
--- a/drivers/mtd/nand/raw/ingenic/jz4740_ecc.c
+++ b/drivers/mtd/nand/raw/ingenic/jz4740_ecc.c
@@ -90,8 +90,8 @@ static int jz4740_ecc_calculate(struct ingenic_ecc *ecc,
 	 * If the written data is completely 0xff, we also want to write 0xff as
 	 * ECC, otherwise we will get in trouble when doing subpage writes.
 	 */
-	if (memcmp(ecc_code, empty_block_ecc, ARRAY_SIZE(empty_block_ecc)) == 0)
-		memset(ecc_code, 0xff, ARRAY_SIZE(empty_block_ecc));
+	if (memcmp(ecc_code, empty_block_ecc, sizeof(empty_block_ecc)) == 0)
+		memset(ecc_code, 0xff, sizeof(empty_block_ecc));
 
 	return 0;
 }
diff --git a/drivers/mtd/nand/raw/internals.h b/drivers/mtd/nand/raw/internals.h
index 03866b0aadea..012876e14317 100644
--- a/drivers/mtd/nand/raw/internals.h
+++ b/drivers/mtd/nand/raw/internals.h
@@ -53,12 +53,12 @@ struct nand_manufacturer_ops {
 };
 
 /**
- * struct nand_manufacturer - NAND Flash Manufacturer structure
+ * struct nand_manufacturer_desc - NAND Flash Manufacturer descriptor
  * @name: Manufacturer name
  * @id: manufacturer ID code of device.
  * @ops: manufacturer operations
  */
-struct nand_manufacturer {
+struct nand_manufacturer_desc {
 	int id;
 	char *name;
 	const struct nand_manufacturer_ops *ops;
@@ -79,14 +79,21 @@ extern const struct nand_manufacturer_ops toshiba_nand_manuf_ops;
 extern const struct mtd_pairing_scheme dist3_pairing_scheme;
 
 /* Core functions */
-const struct nand_manufacturer *nand_get_manufacturer(u8 id);
+const struct nand_manufacturer_desc *nand_get_manufacturer_desc(u8 id);
 int nand_bbm_get_next_page(struct nand_chip *chip, int page);
 int nand_markbad_bbm(struct nand_chip *chip, loff_t ofs);
 int nand_erase_nand(struct nand_chip *chip, struct erase_info *instr,
 		    int allowbbt);
-int onfi_fill_data_interface(struct nand_chip *chip,
-			     enum nand_data_interface_type type,
-			     int timing_mode);
+void onfi_fill_interface_config(struct nand_chip *chip,
+				struct nand_interface_config *iface,
+				enum nand_interface_type type,
+				unsigned int timing_mode);
+unsigned int
+onfi_find_closest_sdr_mode(const struct nand_sdr_timings *spec_timings);
+int nand_choose_best_sdr_timings(struct nand_chip *chip,
+				 struct nand_interface_config *iface,
+				 struct nand_sdr_timings *spec_timings);
+const struct nand_interface_config *nand_get_reset_interface_config(void);
 int nand_get_features(struct nand_chip *chip, int addr, u8 *subfeature_param);
 int nand_set_features(struct nand_chip *chip, int addr, u8 *subfeature_param);
 int nand_read_page_raw_notsupp(struct nand_chip *chip, u8 *buf,
@@ -130,10 +137,10 @@ static inline int nand_exec_op(struct nand_chip *chip,
 	return chip->controller->ops->exec_op(chip, op, false);
 }
 
-static inline bool nand_has_setup_data_iface(struct nand_chip *chip)
+static inline bool nand_controller_can_setup_interface(struct nand_chip *chip)
 {
 	if (!chip->controller || !chip->controller->ops ||
-	    !chip->controller->ops->setup_data_interface)
+	    !chip->controller->ops->setup_interface)
 		return false;
 
 	if (chip->options & NAND_KEEP_TIMINGS)
diff --git a/drivers/mtd/nand/raw/marvell_nand.c b/drivers/mtd/nand/raw/marvell_nand.c
index 260a0430313e..8482d3bd8b1f 100644
--- a/drivers/mtd/nand/raw/marvell_nand.c
+++ b/drivers/mtd/nand/raw/marvell_nand.c
@@ -1096,6 +1096,8 @@ static int marvell_nfc_hw_ecc_hmg_do_write_page(struct nand_chip *chip,
 						const u8 *oob_buf, bool raw,
 						int page)
 {
+	const struct nand_sdr_timings *sdr =
+		nand_get_sdr_timings(nand_get_interface_config(chip));
 	struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip);
 	struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
 	const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout;
@@ -1141,7 +1143,7 @@ static int marvell_nfc_hw_ecc_hmg_do_write_page(struct nand_chip *chip,
 		return ret;
 
 	ret = marvell_nfc_wait_op(chip,
-				  PSEC_TO_MSEC(chip->data_interface.timings.sdr.tPROG_max));
+				  PSEC_TO_MSEC(sdr->tPROG_max));
 	return ret;
 }
 
@@ -1562,6 +1564,8 @@ static int marvell_nfc_hw_ecc_bch_write_page(struct nand_chip *chip,
 					     const u8 *buf,
 					     int oob_required, int page)
 {
+	const struct nand_sdr_timings *sdr =
+		nand_get_sdr_timings(nand_get_interface_config(chip));
 	struct mtd_info *mtd = nand_to_mtd(chip);
 	const struct marvell_hw_ecc_layout *lt = to_marvell_nand(chip)->layout;
 	const u8 *data = buf;
@@ -1598,8 +1602,7 @@ static int marvell_nfc_hw_ecc_bch_write_page(struct nand_chip *chip,
 		marvell_nfc_wait_ndrun(chip);
 	}
 
-	ret = marvell_nfc_wait_op(chip,
-				  PSEC_TO_MSEC(chip->data_interface.timings.sdr.tPROG_max));
+	ret = marvell_nfc_wait_op(chip, PSEC_TO_MSEC(sdr->tPROG_max));
 
 	marvell_nfc_disable_hw_ecc(chip);
 
@@ -2305,9 +2308,8 @@ static struct nand_bbt_descr bbt_mirror_descr = {
 	.pattern = bbt_mirror_pattern
 };
 
-static int marvell_nfc_setup_data_interface(struct nand_chip *chip, int chipnr,
-					    const struct nand_data_interface
-					    *conf)
+static int marvell_nfc_setup_interface(struct nand_chip *chip, int chipnr,
+				       const struct nand_interface_config *conf)
 {
 	struct marvell_nand_chip *marvell_nand = to_marvell_nand(chip);
 	struct marvell_nfc *nfc = to_marvell_nfc(chip->controller);
@@ -2508,7 +2510,7 @@ static int marvell_nand_attach_chip(struct nand_chip *chip)
 static const struct nand_controller_ops marvell_nand_controller_ops = {
 	.attach_chip = marvell_nand_attach_chip,
 	.exec_op = marvell_nfc_exec_op,
-	.setup_data_interface = marvell_nfc_setup_data_interface,
+	.setup_interface = marvell_nfc_setup_interface,
 };
 
 static int marvell_nand_chip_init(struct device *dev, struct marvell_nfc *nfc,
@@ -2644,7 +2646,7 @@ static int marvell_nand_chip_init(struct device *dev, struct marvell_nfc *nfc,
 
 	/*
 	 * Save a reference value for timing registers before
-	 * ->setup_data_interface() is called.
+	 * ->setup_interface() is called.
 	 */
 	marvell_nand->ndtr0 = readl_relaxed(nfc->regs + NDTR0);
 	marvell_nand->ndtr1 = readl_relaxed(nfc->regs + NDTR1);
diff --git a/drivers/mtd/nand/raw/meson_nand.c b/drivers/mtd/nand/raw/meson_nand.c
index 3f376471f3f7..0e5829a2b54f 100644
--- a/drivers/mtd/nand/raw/meson_nand.c
+++ b/drivers/mtd/nand/raw/meson_nand.c
@@ -573,10 +573,10 @@ static int meson_nfc_write_buf(struct nand_chip *nand, u8 *buf, int len)
 static int meson_nfc_rw_cmd_prepare_and_execute(struct nand_chip *nand,
 						int page, bool in)
 {
+	const struct nand_sdr_timings *sdr =
+		nand_get_sdr_timings(nand_get_interface_config(nand));
 	struct mtd_info *mtd = nand_to_mtd(nand);
 	struct meson_nfc *nfc = nand_get_controller_data(nand);
-	const struct nand_sdr_timings *sdr =
-		nand_get_sdr_timings(&nand->data_interface);
 	u32 *addrs = nfc->cmdfifo.rw.addrs;
 	u32 cs = nfc->param.chip_select;
 	u32 cmd0, cmd_num, row_start;
@@ -626,9 +626,9 @@ static int meson_nfc_rw_cmd_prepare_and_execute(struct nand_chip *nand,
 static int meson_nfc_write_page_sub(struct nand_chip *nand,
 				    int page, int raw)
 {
-	struct mtd_info *mtd = nand_to_mtd(nand);
 	const struct nand_sdr_timings *sdr =
-		nand_get_sdr_timings(&nand->data_interface);
+		nand_get_sdr_timings(nand_get_interface_config(nand));
+	struct mtd_info *mtd = nand_to_mtd(nand);
 	struct meson_nfc_nand_chip *meson_chip = to_meson_nand(nand);
 	struct meson_nfc *nfc = nand_get_controller_data(nand);
 	int data_len, info_len;
@@ -1097,8 +1097,8 @@ static int meson_chip_buffer_init(struct nand_chip *nand)
 }
 
 static
-int meson_nfc_setup_data_interface(struct nand_chip *nand, int csline,
-				   const struct nand_data_interface *conf)
+int meson_nfc_setup_interface(struct nand_chip *nand, int csline,
+			      const struct nand_interface_config *conf)
 {
 	struct meson_nfc_nand_chip *meson_chip = to_meson_nand(nand);
 	const struct nand_sdr_timings *timings;
@@ -1222,7 +1222,7 @@ static int meson_nand_attach_chip(struct nand_chip *nand)
 static const struct nand_controller_ops meson_nand_controller_ops = {
 	.attach_chip = meson_nand_attach_chip,
 	.detach_chip = meson_nand_detach_chip,
-	.setup_data_interface = meson_nfc_setup_data_interface,
+	.setup_interface = meson_nfc_setup_interface,
 	.exec_op = meson_nfc_exec_op,
 };
 
diff --git a/drivers/mtd/nand/raw/mtk_nand.c b/drivers/mtd/nand/raw/mtk_nand.c
index c1a6e31aabb8..ad1b55dab211 100644
--- a/drivers/mtd/nand/raw/mtk_nand.c
+++ b/drivers/mtd/nand/raw/mtk_nand.c
@@ -387,44 +387,6 @@ static int mtk_nfc_hw_runtime_config(struct mtd_info *mtd)
 	return 0;
 }
 
-static void mtk_nfc_select_chip(struct nand_chip *nand, int chip)
-{
-	struct mtk_nfc *nfc = nand_get_controller_data(nand);
-	struct mtk_nfc_nand_chip *mtk_nand = to_mtk_nand(nand);
-
-	if (chip < 0)
-		return;
-
-	mtk_nfc_hw_runtime_config(nand_to_mtd(nand));
-
-	nfi_writel(nfc, mtk_nand->sels[chip], NFI_CSEL);
-}
-
-static int mtk_nfc_dev_ready(struct nand_chip *nand)
-{
-	struct mtk_nfc *nfc = nand_get_controller_data(nand);
-
-	if (nfi_readl(nfc, NFI_STA) & STA_BUSY)
-		return 0;
-
-	return 1;
-}
-
-static void mtk_nfc_cmd_ctrl(struct nand_chip *chip, int dat,
-			     unsigned int ctrl)
-{
-	struct mtk_nfc *nfc = nand_get_controller_data(chip);
-
-	if (ctrl & NAND_ALE) {
-		mtk_nfc_send_address(nfc, dat);
-	} else if (ctrl & NAND_CLE) {
-		mtk_nfc_hw_reset(nfc);
-
-		nfi_writew(nfc, CNFG_OP_CUST, NFI_CNFG);
-		mtk_nfc_send_command(nfc, dat);
-	}
-}
-
 static inline void mtk_nfc_wait_ioready(struct mtk_nfc *nfc)
 {
 	int rc;
@@ -501,8 +463,76 @@ static void mtk_nfc_write_buf(struct nand_chip *chip, const u8 *buf, int len)
 		mtk_nfc_write_byte(chip, buf[i]);
 }
 
-static int mtk_nfc_setup_data_interface(struct nand_chip *chip, int csline,
-					const struct nand_data_interface *conf)
+static int mtk_nfc_exec_instr(struct nand_chip *chip,
+			      const struct nand_op_instr *instr)
+{
+	struct mtk_nfc *nfc = nand_get_controller_data(chip);
+	unsigned int i;
+	u32 status;
+
+	switch (instr->type) {
+	case NAND_OP_CMD_INSTR:
+		mtk_nfc_send_command(nfc, instr->ctx.cmd.opcode);
+		return 0;
+	case NAND_OP_ADDR_INSTR:
+		for (i = 0; i < instr->ctx.addr.naddrs; i++)
+			mtk_nfc_send_address(nfc, instr->ctx.addr.addrs[i]);
+		return 0;
+	case NAND_OP_DATA_IN_INSTR:
+		mtk_nfc_read_buf(chip, instr->ctx.data.buf.in,
+				 instr->ctx.data.len);
+		return 0;
+	case NAND_OP_DATA_OUT_INSTR:
+		mtk_nfc_write_buf(chip, instr->ctx.data.buf.out,
+				  instr->ctx.data.len);
+		return 0;
+	case NAND_OP_WAITRDY_INSTR:
+		return readl_poll_timeout(nfc->regs + NFI_STA, status,
+					  status & STA_BUSY, 20,
+					  instr->ctx.waitrdy.timeout_ms);
+	default:
+		break;
+	}
+
+	return -EINVAL;
+}
+
+static void mtk_nfc_select_target(struct nand_chip *nand, unsigned int cs)
+{
+	struct mtk_nfc *nfc = nand_get_controller_data(nand);
+	struct mtk_nfc_nand_chip *mtk_nand = to_mtk_nand(nand);
+
+	mtk_nfc_hw_runtime_config(nand_to_mtd(nand));
+
+	nfi_writel(nfc, mtk_nand->sels[cs], NFI_CSEL);
+}
+
+static int mtk_nfc_exec_op(struct nand_chip *chip,
+			   const struct nand_operation *op,
+			   bool check_only)
+{
+	struct mtk_nfc *nfc = nand_get_controller_data(chip);
+	unsigned int i;
+	int ret = 0;
+
+	if (check_only)
+		return 0;
+
+	mtk_nfc_hw_reset(nfc);
+	nfi_writew(nfc, CNFG_OP_CUST, NFI_CNFG);
+	mtk_nfc_select_target(chip, op->cs);
+
+	for (i = 0; i < op->ninstrs; i++) {
+		ret = mtk_nfc_exec_instr(chip, &op->instrs[i]);
+		if (ret)
+			break;
+	}
+
+	return ret;
+}
+
+static int mtk_nfc_setup_interface(struct nand_chip *chip, int csline,
+				   const struct nand_interface_config *conf)
 {
 	struct mtk_nfc *nfc = nand_get_controller_data(chip);
 	const struct nand_sdr_timings *timings;
@@ -803,6 +833,7 @@ static int mtk_nfc_write_page(struct mtd_info *mtd, struct nand_chip *chip,
 	u32 reg;
 	int ret;
 
+	mtk_nfc_select_target(chip, chip->cur_cs);
 	nand_prog_page_begin_op(chip, page, 0, NULL, 0);
 
 	if (!raw) {
@@ -920,6 +951,7 @@ static int mtk_nfc_read_subpage(struct mtd_info *mtd, struct nand_chip *chip,
 	u8 *buf;
 	int rc;
 
+	mtk_nfc_select_target(chip, chip->cur_cs);
 	start = data_offs / chip->ecc.size;
 	end = DIV_ROUND_UP(data_offs + readlen, chip->ecc.size);
 
@@ -1325,7 +1357,8 @@ static int mtk_nfc_attach_chip(struct nand_chip *chip)
 
 static const struct nand_controller_ops mtk_nfc_controller_ops = {
 	.attach_chip = mtk_nfc_attach_chip,
-	.setup_data_interface = mtk_nfc_setup_data_interface,
+	.setup_interface = mtk_nfc_setup_interface,
+	.exec_op = mtk_nfc_exec_op,
 };
 
 static int mtk_nfc_nand_chip_init(struct device *dev, struct mtk_nfc *nfc,
@@ -1381,13 +1414,6 @@ static int mtk_nfc_nand_chip_init(struct device *dev, struct mtk_nfc *nfc,
 	nand_set_controller_data(nand, nfc);
 
 	nand->options |= NAND_USES_DMA | NAND_SUBPAGE_READ;
-	nand->legacy.dev_ready = mtk_nfc_dev_ready;
-	nand->legacy.select_chip = mtk_nfc_select_chip;
-	nand->legacy.write_byte = mtk_nfc_write_byte;
-	nand->legacy.write_buf = mtk_nfc_write_buf;
-	nand->legacy.read_byte = mtk_nfc_read_byte;
-	nand->legacy.read_buf = mtk_nfc_read_buf;
-	nand->legacy.cmd_ctrl = mtk_nfc_cmd_ctrl;
 
 	/* set default mode in case dt entry is missing */
 	nand->ecc.mode = NAND_ECC_HW;
diff --git a/drivers/mtd/nand/raw/mxc_nand.c b/drivers/mtd/nand/raw/mxc_nand.c
index 09dacb83cb5a..a043d76b48cb 100644
--- a/drivers/mtd/nand/raw/mxc_nand.c
+++ b/drivers/mtd/nand/raw/mxc_nand.c
@@ -137,8 +137,8 @@ struct mxc_nand_devtype_data {
 	u32 (*get_ecc_status)(struct mxc_nand_host *);
 	const struct mtd_ooblayout_ops *ooblayout;
 	void (*select_chip)(struct nand_chip *chip, int cs);
-	int (*setup_data_interface)(struct nand_chip *chip, int csline,
-				    const struct nand_data_interface *conf);
+	int (*setup_interface)(struct nand_chip *chip, int csline,
+			       const struct nand_interface_config *conf);
 	void (*enable_hwecc)(struct nand_chip *chip, bool enable);
 
 	/*
@@ -1139,8 +1139,8 @@ static void preset_v1(struct mtd_info *mtd)
 	writew(0x4, NFC_V1_V2_WRPROT);
 }
 
-static int mxc_nand_v2_setup_data_interface(struct nand_chip *chip, int csline,
-					const struct nand_data_interface *conf)
+static int mxc_nand_v2_setup_interface(struct nand_chip *chip, int csline,
+				       const struct nand_interface_config *conf)
 {
 	struct mxc_nand_host *host = nand_get_controller_data(chip);
 	int tRC_min_ns, tRC_ps, ret;
@@ -1432,7 +1432,7 @@ static int mxc_nand_get_features(struct nand_chip *chip, int addr,
 }
 
 /*
- * The generic flash bbt decriptors overlap with our ecc
+ * The generic flash bbt descriptors overlap with our ecc
  * hardware, so define some i.MX specific ones.
  */
 static uint8_t bbt_pattern[] = { 'B', 'b', 't', '0' };
@@ -1521,7 +1521,7 @@ static const struct mxc_nand_devtype_data imx25_nand_devtype_data = {
 	.get_ecc_status = get_ecc_status_v2,
 	.ooblayout = &mxc_v2_ooblayout_ops,
 	.select_chip = mxc_nand_select_chip_v2,
-	.setup_data_interface = mxc_nand_v2_setup_data_interface,
+	.setup_interface = mxc_nand_v2_setup_interface,
 	.enable_hwecc = mxc_nand_enable_hwecc_v1_v2,
 	.irqpending_quirk = 0,
 	.needs_ip = 0,
@@ -1738,17 +1738,17 @@ static int mxcnd_attach_chip(struct nand_chip *chip)
 	return 0;
 }
 
-static int mxcnd_setup_data_interface(struct nand_chip *chip, int chipnr,
-				      const struct nand_data_interface *conf)
+static int mxcnd_setup_interface(struct nand_chip *chip, int chipnr,
+				 const struct nand_interface_config *conf)
 {
 	struct mxc_nand_host *host = nand_get_controller_data(chip);
 
-	return host->devtype_data->setup_data_interface(chip, chipnr, conf);
+	return host->devtype_data->setup_interface(chip, chipnr, conf);
 }
 
 static const struct nand_controller_ops mxcnd_controller_ops = {
 	.attach_chip = mxcnd_attach_chip,
-	.setup_data_interface = mxcnd_setup_data_interface,
+	.setup_interface = mxcnd_setup_interface,
 };
 
 static int mxcnd_probe(struct platform_device *pdev)
@@ -1809,7 +1809,7 @@ static int mxcnd_probe(struct platform_device *pdev)
 	if (err < 0)
 		return err;
 
-	if (!host->devtype_data->setup_data_interface)
+	if (!host->devtype_data->setup_interface)
 		this->options |= NAND_KEEP_TIMINGS;
 
 	if (host->devtype_data->needs_ip) {
diff --git a/drivers/mtd/nand/raw/mxic_nand.c b/drivers/mtd/nand/raw/mxic_nand.c
index 57f36721f4c6..d66b5b0971fa 100644
--- a/drivers/mtd/nand/raw/mxic_nand.c
+++ b/drivers/mtd/nand/raw/mxic_nand.c
@@ -451,8 +451,8 @@ static int mxic_nfc_exec_op(struct nand_chip *chip,
 	return ret;
 }
 
-static int mxic_nfc_setup_data_interface(struct nand_chip *chip, int chipnr,
-					 const struct nand_data_interface *conf)
+static int mxic_nfc_setup_interface(struct nand_chip *chip, int chipnr,
+				    const struct nand_interface_config *conf)
 {
 	struct mxic_nand_ctlr *nfc = nand_get_controller_data(chip);
 	const struct nand_sdr_timings *sdr;
@@ -480,7 +480,7 @@ static int mxic_nfc_setup_data_interface(struct nand_chip *chip, int chipnr,
 
 static const struct nand_controller_ops mxic_nand_controller_ops = {
 	.exec_op = mxic_nfc_exec_op,
-	.setup_data_interface = mxic_nfc_setup_data_interface,
+	.setup_interface = mxic_nfc_setup_interface,
 };
 
 static int mxic_nfc_probe(struct platform_device *pdev)
diff --git a/drivers/mtd/nand/raw/nand_base.c b/drivers/mtd/nand/raw/nand_base.c
index 45124dbb1835..0c768cb88f96 100644
--- a/drivers/mtd/nand/raw/nand_base.c
+++ b/drivers/mtd/nand/raw/nand_base.c
@@ -773,7 +773,7 @@ int nand_soft_waitrdy(struct nand_chip *chip, unsigned long timeout_ms)
 		return -ENOTSUPP;
 
 	/* Wait tWB before polling the STATUS reg. */
-	timings = nand_get_sdr_timings(&chip->data_interface);
+	timings = nand_get_sdr_timings(nand_get_interface_config(chip));
 	ndelay(PSEC_TO_NSEC(timings->tWB_max));
 
 	ret = nand_status_op(chip, NULL);
@@ -898,7 +898,7 @@ static bool nand_supports_set_features(struct nand_chip *chip, int addr)
 }
 
 /**
- * nand_reset_data_interface - Reset data interface and timings
+ * nand_reset_interface - Reset data interface and timings
  * @chip: The NAND chip
  * @chipnr: Internal die id
  *
@@ -906,11 +906,12 @@ static bool nand_supports_set_features(struct nand_chip *chip, int addr)
  *
  * Returns 0 for success or negative error code otherwise.
  */
-static int nand_reset_data_interface(struct nand_chip *chip, int chipnr)
+static int nand_reset_interface(struct nand_chip *chip, int chipnr)
 {
+	const struct nand_controller_ops *ops = chip->controller->ops;
 	int ret;
 
-	if (!nand_has_setup_data_iface(chip))
+	if (!nand_controller_can_setup_interface(chip))
 		return 0;
 
 	/*
@@ -927,9 +928,9 @@ static int nand_reset_data_interface(struct nand_chip *chip, int chipnr)
 	 * timings to timing mode 0.
 	 */
 
-	onfi_fill_data_interface(chip, NAND_SDR_IFACE, 0);
-	ret = chip->controller->ops->setup_data_interface(chip, chipnr,
-							&chip->data_interface);
+	chip->current_interface_config = nand_get_reset_interface_config();
+	ret = ops->setup_interface(chip, chipnr,
+				   chip->current_interface_config);
 	if (ret)
 		pr_err("Failed to configure data interface to SDR timing mode 0\n");
 
@@ -937,28 +938,36 @@ static int nand_reset_data_interface(struct nand_chip *chip, int chipnr)
 }
 
 /**
- * nand_setup_data_interface - Setup the best data interface and timings
+ * nand_setup_interface - Setup the best data interface and timings
  * @chip: The NAND chip
  * @chipnr: Internal die id
  *
- * Find and configure the best data interface and NAND timings supported by
- * the chip and the driver.
- * First tries to retrieve supported timing modes from ONFI information,
- * and if the NAND chip does not support ONFI, relies on the
- * ->onfi_timing_mode_default specified in the nand_ids table.
+ * Configure what has been reported to be the best data interface and NAND
+ * timings supported by the chip and the driver.
  *
  * Returns 0 for success or negative error code otherwise.
  */
-static int nand_setup_data_interface(struct nand_chip *chip, int chipnr)
+static int nand_setup_interface(struct nand_chip *chip, int chipnr)
 {
-	u8 tmode_param[ONFI_SUBFEATURE_PARAM_LEN] = {
-		chip->onfi_timing_mode_default,
-	};
+	const struct nand_controller_ops *ops = chip->controller->ops;
+	u8 tmode_param[ONFI_SUBFEATURE_PARAM_LEN] = { };
 	int ret;
 
-	if (!nand_has_setup_data_iface(chip))
+	if (!nand_controller_can_setup_interface(chip))
 		return 0;
 
+	/*
+	 * A nand_reset_interface() put both the NAND chip and the NAND
+	 * controller in timings mode 0. If the default mode for this chip is
+	 * also 0, no need to proceed to the change again. Plus, at probe time,
+	 * nand_setup_interface() uses ->set/get_features() which would
+	 * fail anyway as the parameter page is not available yet.
+	 */
+	if (!chip->best_interface_config)
+		return 0;
+
+	tmode_param[0] = chip->best_interface_config->timings.mode;
+
 	/* Change the mode on the chip side (if supported by the NAND chip) */
 	if (nand_supports_set_features(chip, ONFI_FEATURE_ADDR_TIMING_MODE)) {
 		nand_select_target(chip, chipnr);
@@ -970,14 +979,13 @@ static int nand_setup_data_interface(struct nand_chip *chip, int chipnr)
 	}
 
 	/* Change the mode on the controller side */
-	ret = chip->controller->ops->setup_data_interface(chip, chipnr,
-							&chip->data_interface);
+	ret = ops->setup_interface(chip, chipnr, chip->best_interface_config);
 	if (ret)
 		return ret;
 
 	/* Check the mode has been accepted by the chip, if supported */
 	if (!nand_supports_get_features(chip, ONFI_FEATURE_ADDR_TIMING_MODE))
-		return 0;
+		goto update_interface_config;
 
 	memset(tmode_param, 0, ONFI_SUBFEATURE_PARAM_LEN);
 	nand_select_target(chip, chipnr);
@@ -987,12 +995,15 @@ static int nand_setup_data_interface(struct nand_chip *chip, int chipnr)
 	if (ret)
 		goto err_reset_chip;
 
-	if (tmode_param[0] != chip->onfi_timing_mode_default) {
+	if (tmode_param[0] != chip->best_interface_config->timings.mode) {
 		pr_warn("timing mode %d not acknowledged by the NAND chip\n",
-			chip->onfi_timing_mode_default);
+			chip->best_interface_config->timings.mode);
 		goto err_reset_chip;
 	}
 
+update_interface_config:
+	chip->current_interface_config = chip->best_interface_config;
+
 	return 0;
 
 err_reset_chip:
@@ -1000,7 +1011,7 @@ err_reset_chip:
 	 * Fallback to mode 0 if the chip explicitly did not ack the chosen
 	 * timing mode.
 	 */
-	nand_reset_data_interface(chip, chipnr);
+	nand_reset_interface(chip, chipnr);
 	nand_select_target(chip, chipnr);
 	nand_reset_op(chip);
 	nand_deselect_target(chip);
@@ -1009,62 +1020,93 @@ err_reset_chip:
 }
 
 /**
- * nand_init_data_interface - find the best data interface and timings
- * @chip: The NAND chip
- *
- * Find the best data interface and NAND timings supported by the chip
- * and the driver.
- * First tries to retrieve supported timing modes from ONFI information,
- * and if the NAND chip does not support ONFI, relies on the
- * ->onfi_timing_mode_default specified in the nand_ids table. After this
- * function nand_chip->data_interface is initialized with the best timing mode
- * available.
+ * nand_choose_best_sdr_timings - Pick up the best SDR timings that both the
+ *                                NAND controller and the NAND chip support
+ * @chip: the NAND chip
+ * @iface: the interface configuration (can eventually be updated)
+ * @spec_timings: specific timings, when not fitting the ONFI specification
  *
- * Returns 0 for success or negative error code otherwise.
+ * If specific timings are provided, use them. Otherwise, retrieve supported
+ * timing modes from ONFI information.
  */
-static int nand_init_data_interface(struct nand_chip *chip)
+int nand_choose_best_sdr_timings(struct nand_chip *chip,
+				 struct nand_interface_config *iface,
+				 struct nand_sdr_timings *spec_timings)
 {
-	int modes, mode, ret;
+	const struct nand_controller_ops *ops = chip->controller->ops;
+	int best_mode = 0, mode, ret;
 
-	if (!nand_has_setup_data_iface(chip))
-		return 0;
+	iface->type = NAND_SDR_IFACE;
 
-	/*
-	 * First try to identify the best timings from ONFI parameters and
-	 * if the NAND does not support ONFI, fallback to the default ONFI
-	 * timing mode.
-	 */
-	if (chip->parameters.onfi) {
-		modes = chip->parameters.onfi->async_timing_mode;
-	} else {
-		if (!chip->onfi_timing_mode_default)
-			return 0;
+	if (spec_timings) {
+		iface->timings.sdr = *spec_timings;
+		iface->timings.mode = onfi_find_closest_sdr_mode(spec_timings);
 
-		modes = GENMASK(chip->onfi_timing_mode_default, 0);
+		/* Verify the controller supports the requested interface */
+		ret = ops->setup_interface(chip, NAND_DATA_IFACE_CHECK_ONLY,
+					   iface);
+		if (!ret) {
+			chip->best_interface_config = iface;
+			return ret;
+		}
+
+		/* Fallback to slower modes */
+		best_mode = iface->timings.mode;
+	} else if (chip->parameters.onfi) {
+		best_mode = fls(chip->parameters.onfi->async_timing_mode) - 1;
 	}
 
-	for (mode = fls(modes) - 1; mode >= 0; mode--) {
-		ret = onfi_fill_data_interface(chip, NAND_SDR_IFACE, mode);
-		if (ret)
-			continue;
+	for (mode = best_mode; mode >= 0; mode--) {
+		onfi_fill_interface_config(chip, iface, NAND_SDR_IFACE, mode);
 
-		/*
-		 * Pass NAND_DATA_IFACE_CHECK_ONLY to only check if the
-		 * controller supports the requested timings.
-		 */
-		ret = chip->controller->ops->setup_data_interface(chip,
-						 NAND_DATA_IFACE_CHECK_ONLY,
-						 &chip->data_interface);
-		if (!ret) {
-			chip->onfi_timing_mode_default = mode;
+		ret = ops->setup_interface(chip, NAND_DATA_IFACE_CHECK_ONLY,
+					   iface);
+		if (!ret)
 			break;
-		}
 	}
 
+	chip->best_interface_config = iface;
+
 	return 0;
 }
 
 /**
+ * nand_choose_interface_config - find the best data interface and timings
+ * @chip: The NAND chip
+ *
+ * Find the best data interface and NAND timings supported by the chip
+ * and the driver. Eventually let the NAND manufacturer driver propose his own
+ * set of timings.
+ *
+ * After this function nand_chip->interface_config is initialized with the best
+ * timing mode available.
+ *
+ * Returns 0 for success or negative error code otherwise.
+ */
+static int nand_choose_interface_config(struct nand_chip *chip)
+{
+	struct nand_interface_config *iface;
+	int ret;
+
+	if (!nand_controller_can_setup_interface(chip))
+		return 0;
+
+	iface = kzalloc(sizeof(*iface), GFP_KERNEL);
+	if (!iface)
+		return -ENOMEM;
+
+	if (chip->ops.choose_interface_config)
+		ret = chip->ops.choose_interface_config(chip, iface);
+	else
+		ret = nand_choose_best_sdr_timings(chip, iface, NULL);
+
+	if (ret)
+		kfree(iface);
+
+	return ret;
+}
+
+/**
  * nand_fill_column_cycles - fill the column cycles of an address
  * @chip: The NAND chip
  * @addrs: Array of address cycles to fill
@@ -1122,9 +1164,9 @@ static int nand_sp_exec_read_page_op(struct nand_chip *chip, unsigned int page,
 				     unsigned int offset_in_page, void *buf,
 				     unsigned int len)
 {
-	struct mtd_info *mtd = nand_to_mtd(chip);
 	const struct nand_sdr_timings *sdr =
-		nand_get_sdr_timings(&chip->data_interface);
+		nand_get_sdr_timings(nand_get_interface_config(chip));
+	struct mtd_info *mtd = nand_to_mtd(chip);
 	u8 addrs[4];
 	struct nand_op_instr instrs[] = {
 		NAND_OP_CMD(NAND_CMD_READ0, 0),
@@ -1166,7 +1208,7 @@ static int nand_lp_exec_read_page_op(struct nand_chip *chip, unsigned int page,
 				     unsigned int len)
 {
 	const struct nand_sdr_timings *sdr =
-		nand_get_sdr_timings(&chip->data_interface);
+		nand_get_sdr_timings(nand_get_interface_config(chip));
 	u8 addrs[5];
 	struct nand_op_instr instrs[] = {
 		NAND_OP_CMD(NAND_CMD_READ0, 0),
@@ -1263,7 +1305,7 @@ int nand_read_param_page_op(struct nand_chip *chip, u8 page, void *buf,
 
 	if (nand_has_exec_op(chip)) {
 		const struct nand_sdr_timings *sdr =
-			nand_get_sdr_timings(&chip->data_interface);
+			nand_get_sdr_timings(nand_get_interface_config(chip));
 		struct nand_op_instr instrs[] = {
 			NAND_OP_CMD(NAND_CMD_PARAM, 0),
 			NAND_OP_ADDR(1, &page, PSEC_TO_NSEC(sdr->tWB_max)),
@@ -1318,7 +1360,7 @@ int nand_change_read_column_op(struct nand_chip *chip,
 
 	if (nand_has_exec_op(chip)) {
 		const struct nand_sdr_timings *sdr =
-			nand_get_sdr_timings(&chip->data_interface);
+			nand_get_sdr_timings(nand_get_interface_config(chip));
 		u8 addrs[2] = {};
 		struct nand_op_instr instrs[] = {
 			NAND_OP_CMD(NAND_CMD_RNDOUT, 0),
@@ -1392,9 +1434,9 @@ static int nand_exec_prog_page_op(struct nand_chip *chip, unsigned int page,
 				  unsigned int offset_in_page, const void *buf,
 				  unsigned int len, bool prog)
 {
-	struct mtd_info *mtd = nand_to_mtd(chip);
 	const struct nand_sdr_timings *sdr =
-		nand_get_sdr_timings(&chip->data_interface);
+		nand_get_sdr_timings(nand_get_interface_config(chip));
+	struct mtd_info *mtd = nand_to_mtd(chip);
 	u8 addrs[5] = {};
 	struct nand_op_instr instrs[] = {
 		/*
@@ -1517,7 +1559,7 @@ int nand_prog_page_end_op(struct nand_chip *chip)
 
 	if (nand_has_exec_op(chip)) {
 		const struct nand_sdr_timings *sdr =
-			nand_get_sdr_timings(&chip->data_interface);
+			nand_get_sdr_timings(nand_get_interface_config(chip));
 		struct nand_op_instr instrs[] = {
 			NAND_OP_CMD(NAND_CMD_PAGEPROG,
 				    PSEC_TO_NSEC(sdr->tWB_max)),
@@ -1624,7 +1666,7 @@ int nand_change_write_column_op(struct nand_chip *chip,
 
 	if (nand_has_exec_op(chip)) {
 		const struct nand_sdr_timings *sdr =
-			nand_get_sdr_timings(&chip->data_interface);
+			nand_get_sdr_timings(nand_get_interface_config(chip));
 		u8 addrs[2];
 		struct nand_op_instr instrs[] = {
 			NAND_OP_CMD(NAND_CMD_RNDIN, 0),
@@ -1679,7 +1721,7 @@ int nand_readid_op(struct nand_chip *chip, u8 addr, void *buf,
 
 	if (nand_has_exec_op(chip)) {
 		const struct nand_sdr_timings *sdr =
-			nand_get_sdr_timings(&chip->data_interface);
+			nand_get_sdr_timings(nand_get_interface_config(chip));
 		struct nand_op_instr instrs[] = {
 			NAND_OP_CMD(NAND_CMD_READID, 0),
 			NAND_OP_ADDR(1, &addr, PSEC_TO_NSEC(sdr->tADL_min)),
@@ -1718,7 +1760,7 @@ int nand_status_op(struct nand_chip *chip, u8 *status)
 {
 	if (nand_has_exec_op(chip)) {
 		const struct nand_sdr_timings *sdr =
-			nand_get_sdr_timings(&chip->data_interface);
+			nand_get_sdr_timings(nand_get_interface_config(chip));
 		struct nand_op_instr instrs[] = {
 			NAND_OP_CMD(NAND_CMD_STATUS,
 				    PSEC_TO_NSEC(sdr->tADL_min)),
@@ -1787,7 +1829,7 @@ int nand_erase_op(struct nand_chip *chip, unsigned int eraseblock)
 
 	if (nand_has_exec_op(chip)) {
 		const struct nand_sdr_timings *sdr =
-			nand_get_sdr_timings(&chip->data_interface);
+			nand_get_sdr_timings(nand_get_interface_config(chip));
 		u8 addrs[3] = {	page, page >> 8, page >> 16 };
 		struct nand_op_instr instrs[] = {
 			NAND_OP_CMD(NAND_CMD_ERASE1, 0),
@@ -1846,7 +1888,7 @@ static int nand_set_features_op(struct nand_chip *chip, u8 feature,
 
 	if (nand_has_exec_op(chip)) {
 		const struct nand_sdr_timings *sdr =
-			nand_get_sdr_timings(&chip->data_interface);
+			nand_get_sdr_timings(nand_get_interface_config(chip));
 		struct nand_op_instr instrs[] = {
 			NAND_OP_CMD(NAND_CMD_SET_FEATURES, 0),
 			NAND_OP_ADDR(1, &feature, PSEC_TO_NSEC(sdr->tADL_min)),
@@ -1893,7 +1935,7 @@ static int nand_get_features_op(struct nand_chip *chip, u8 feature,
 
 	if (nand_has_exec_op(chip)) {
 		const struct nand_sdr_timings *sdr =
-			nand_get_sdr_timings(&chip->data_interface);
+			nand_get_sdr_timings(nand_get_interface_config(chip));
 		struct nand_op_instr instrs[] = {
 			NAND_OP_CMD(NAND_CMD_GET_FEATURES, 0),
 			NAND_OP_ADDR(1, &feature, PSEC_TO_NSEC(sdr->tWB_max)),
@@ -1950,7 +1992,7 @@ int nand_reset_op(struct nand_chip *chip)
 {
 	if (nand_has_exec_op(chip)) {
 		const struct nand_sdr_timings *sdr =
-			nand_get_sdr_timings(&chip->data_interface);
+			nand_get_sdr_timings(nand_get_interface_config(chip));
 		struct nand_op_instr instrs[] = {
 			NAND_OP_CMD(NAND_CMD_RESET, PSEC_TO_NSEC(sdr->tWB_max)),
 			NAND_OP_WAIT_RDY(PSEC_TO_MSEC(sdr->tRST_max), 0),
@@ -2480,17 +2522,16 @@ EXPORT_SYMBOL_GPL(nand_subop_get_data_len);
  * @chipnr: Internal die id
  *
  * Save the timings data structure, then apply SDR timings mode 0 (see
- * nand_reset_data_interface for details), do the reset operation, and
- * apply back the previous timings.
+ * nand_reset_interface for details), do the reset operation, and apply
+ * back the previous timings.
  *
  * Returns 0 on success, a negative error code otherwise.
  */
 int nand_reset(struct nand_chip *chip, int chipnr)
 {
-	struct nand_data_interface saved_data_intf = chip->data_interface;
 	int ret;
 
-	ret = nand_reset_data_interface(chip, chipnr);
+	ret = nand_reset_interface(chip, chipnr);
 	if (ret)
 		return ret;
 
@@ -2505,18 +2546,7 @@ int nand_reset(struct nand_chip *chip, int chipnr)
 	if (ret)
 		return ret;
 
-	/*
-	 * A nand_reset_data_interface() put both the NAND chip and the NAND
-	 * controller in timings mode 0. If the default mode for this chip is
-	 * also 0, no need to proceed to the change again. Plus, at probe time,
-	 * nand_setup_data_interface() uses ->set/get_features() which would
-	 * fail anyway as the parameter page is not available yet.
-	 */
-	if (!chip->onfi_timing_mode_default)
-		return 0;
-
-	chip->data_interface = saved_data_intf;
-	ret = nand_setup_data_interface(chip, chipnr);
+	ret = nand_setup_interface(chip, chipnr);
 	if (ret)
 		return ret;
 
@@ -3215,10 +3245,10 @@ static int nand_setup_read_retry(struct nand_chip *chip, int retry_mode)
 	if (retry_mode >= chip->read_retries)
 		return -EINVAL;
 
-	if (!chip->setup_read_retry)
+	if (!chip->ops.setup_read_retry)
 		return -EOPNOTSUPP;
 
-	return chip->setup_read_retry(chip, retry_mode);
+	return chip->ops.setup_read_retry(chip, retry_mode);
 }
 
 static void nand_wait_readrdy(struct nand_chip *chip)
@@ -3228,7 +3258,7 @@ static void nand_wait_readrdy(struct nand_chip *chip)
 	if (!(chip->options & NAND_NEED_READRDY))
 		return;
 
-	sdr = nand_get_sdr_timings(&chip->data_interface);
+	sdr = nand_get_sdr_timings(nand_get_interface_config(chip));
 	WARN_ON(nand_wait_rdy_op(chip, PSEC_TO_MSEC(sdr->tR_max), 0));
 }
 
@@ -4462,8 +4492,8 @@ static int nand_suspend(struct mtd_info *mtd)
 	int ret = 0;
 
 	mutex_lock(&chip->lock);
-	if (chip->suspend)
-		ret = chip->suspend(chip);
+	if (chip->ops.suspend)
+		ret = chip->ops.suspend(chip);
 	if (!ret)
 		chip->suspended = 1;
 	mutex_unlock(&chip->lock);
@@ -4481,8 +4511,8 @@ static void nand_resume(struct mtd_info *mtd)
 
 	mutex_lock(&chip->lock);
 	if (chip->suspended) {
-		if (chip->resume)
-			chip->resume(chip);
+		if (chip->ops.resume)
+			chip->ops.resume(chip);
 		chip->suspended = 0;
 	} else {
 		pr_err("%s called for a chip which is not in suspended state\n",
@@ -4511,10 +4541,10 @@ static int nand_lock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 {
 	struct nand_chip *chip = mtd_to_nand(mtd);
 
-	if (!chip->lock_area)
+	if (!chip->ops.lock_area)
 		return -ENOTSUPP;
 
-	return chip->lock_area(chip, ofs, len);
+	return chip->ops.lock_area(chip, ofs, len);
 }
 
 /**
@@ -4527,10 +4557,10 @@ static int nand_unlock(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 {
 	struct nand_chip *chip = mtd_to_nand(mtd);
 
-	if (!chip->unlock_area)
+	if (!chip->ops.unlock_area)
 		return -ENOTSUPP;
 
-	return chip->unlock_area(chip, ofs, len);
+	return chip->ops.unlock_area(chip, ofs, len);
 }
 
 /* Set default functions */
@@ -4743,8 +4773,6 @@ static bool find_full_id_nand(struct nand_chip *chip,
 		chip->options |= type->options;
 		chip->base.eccreq.strength = NAND_ECC_STRENGTH(type);
 		chip->base.eccreq.step_size = NAND_ECC_STEP(type);
-		chip->onfi_timing_mode_default =
-					type->onfi_timing_mode_default;
 
 		chip->parameters.model = kstrdup(type->name, GFP_KERNEL);
 		if (!chip->parameters.model)
@@ -4810,9 +4838,9 @@ static void nand_manufacturer_cleanup(struct nand_chip *chip)
 }
 
 static const char *
-nand_manufacturer_name(const struct nand_manufacturer *manufacturer)
+nand_manufacturer_name(const struct nand_manufacturer_desc *manufacturer_desc)
 {
-	return manufacturer ? manufacturer->name : "Unknown";
+	return manufacturer_desc ? manufacturer_desc->name : "Unknown";
 }
 
 /*
@@ -4820,7 +4848,7 @@ nand_manufacturer_name(const struct nand_manufacturer *manufacturer)
  */
 static int nand_detect(struct nand_chip *chip, struct nand_flash_dev *type)
 {
-	const struct nand_manufacturer *manufacturer;
+	const struct nand_manufacturer_desc *manufacturer_desc;
 	struct mtd_info *mtd = nand_to_mtd(chip);
 	struct nand_memory_organization *memorg;
 	int busw, ret;
@@ -4877,8 +4905,8 @@ static int nand_detect(struct nand_chip *chip, struct nand_flash_dev *type)
 	chip->id.len = nand_id_len(id_data, ARRAY_SIZE(chip->id.data));
 
 	/* Try to identify manufacturer */
-	manufacturer = nand_get_manufacturer(maf_id);
-	chip->manufacturer.desc = manufacturer;
+	manufacturer_desc = nand_get_manufacturer_desc(maf_id);
+	chip->manufacturer.desc = manufacturer_desc;
 
 	if (!type)
 		type = nand_flash_ids;
@@ -4957,7 +4985,7 @@ ident_done:
 		 */
 		pr_info("device found, Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n",
 			maf_id, dev_id);
-		pr_info("%s %s\n", nand_manufacturer_name(manufacturer),
+		pr_info("%s %s\n", nand_manufacturer_name(manufacturer_desc),
 			mtd->name);
 		pr_warn("bus width %d instead of %d bits\n", busw ? 16 : 8,
 			(chip->options & NAND_BUSWIDTH_16) ? 16 : 8);
@@ -4992,7 +5020,7 @@ ident_done:
 
 	pr_info("device found, Manufacturer ID: 0x%02x, Chip ID: 0x%02x\n",
 		maf_id, dev_id);
-	pr_info("%s %s\n", nand_manufacturer_name(manufacturer),
+	pr_info("%s %s\n", nand_manufacturer_name(manufacturer_desc),
 		chip->parameters.model);
 	pr_info("%d MiB, %s, erase size: %d KiB, page size: %d, OOB size: %d\n",
 		(int)(targetsize >> 20), nand_is_slc(chip) ? "SLC" : "MLC",
@@ -5185,7 +5213,7 @@ static int nand_scan_ident(struct nand_chip *chip, unsigned int maxchips,
 	mutex_init(&chip->lock);
 
 	/* Enforce the right timings for reset/detection */
-	onfi_fill_data_interface(chip, NAND_SDR_IFACE, 0);
+	chip->current_interface_config = nand_get_reset_interface_config();
 
 	ret = nand_dt_init(chip);
 	if (ret)
@@ -5972,16 +6000,16 @@ static int nand_scan_tail(struct nand_chip *chip)
 	if (!mtd->bitflip_threshold)
 		mtd->bitflip_threshold = DIV_ROUND_UP(mtd->ecc_strength * 3, 4);
 
-	/* Initialize the ->data_interface field. */
-	ret = nand_init_data_interface(chip);
+	/* Find the fastest data interface for this chip */
+	ret = nand_choose_interface_config(chip);
 	if (ret)
 		goto err_nanddev_cleanup;
 
 	/* Enter fastest possible mode on all dies. */
 	for (i = 0; i < nanddev_ntargets(&chip->base); i++) {
-		ret = nand_setup_data_interface(chip, i);
+		ret = nand_setup_interface(chip, i);
 		if (ret)
-			goto err_nanddev_cleanup;
+			goto err_free_interface_config;
 	}
 
 	/* Check, if we should skip the bad block table scan */
@@ -5991,10 +6019,12 @@ static int nand_scan_tail(struct nand_chip *chip)
 	/* Build bad block table */
 	ret = nand_create_bbt(chip);
 	if (ret)
-		goto err_nanddev_cleanup;
+		goto err_free_interface_config;
 
 	return 0;
 
+err_free_interface_config:
+	kfree(chip->best_interface_config);
 
 err_nanddev_cleanup:
 	nanddev_cleanup(&chip->base);
@@ -6088,6 +6118,9 @@ void nand_cleanup(struct nand_chip *chip)
 			& NAND_BBT_DYNAMICSTRUCT)
 		kfree(chip->badblock_pattern);
 
+	/* Free the data interface */
+	kfree(chip->best_interface_config);
+
 	/* Free manufacturer priv data. */
 	nand_manufacturer_cleanup(chip);
 
diff --git a/drivers/mtd/nand/raw/nand_bbt.c b/drivers/mtd/nand/raw/nand_bbt.c
index 96045d60471e..344a24fd2ca8 100644
--- a/drivers/mtd/nand/raw/nand_bbt.c
+++ b/drivers/mtd/nand/raw/nand_bbt.c
@@ -1226,7 +1226,7 @@ static int nand_scan_bbt(struct nand_chip *this, struct nand_bbt_descr *bd)
 		return -ENOMEM;
 
 	/*
-	 * If no primary table decriptor is given, scan the device to build a
+	 * If no primary table descriptor is given, scan the device to build a
 	 * memory based bad block table.
 	 */
 	if (!td) {
diff --git a/drivers/mtd/nand/raw/nand_hynix.c b/drivers/mtd/nand/raw/nand_hynix.c
index 7caedaa5b9e5..6d08eb834456 100644
--- a/drivers/mtd/nand/raw/nand_hynix.c
+++ b/drivers/mtd/nand/raw/nand_hynix.c
@@ -337,7 +337,7 @@ static int hynix_mlc_1xnm_rr_init(struct nand_chip *chip,
 	rr->nregs = nregs;
 	rr->regs = hynix_1xnm_mlc_read_retry_regs;
 	hynix->read_retry = rr;
-	chip->setup_read_retry = hynix_nand_setup_read_retry;
+	chip->ops.setup_read_retry = hynix_nand_setup_read_retry;
 	chip->read_retries = nmodes;
 
 out:
@@ -673,6 +673,15 @@ static void hynix_nand_cleanup(struct nand_chip *chip)
 	nand_set_manufacturer_data(chip, NULL);
 }
 
+static int
+h27ucg8t2atrbc_choose_interface_config(struct nand_chip *chip,
+				       struct nand_interface_config *iface)
+{
+	onfi_fill_interface_config(chip, iface, NAND_SDR_IFACE, 4);
+
+	return nand_choose_best_sdr_timings(chip, iface, NULL);
+}
+
 static int hynix_nand_init(struct nand_chip *chip)
 {
 	struct hynix_nand *hynix;
@@ -689,6 +698,11 @@ static int hynix_nand_init(struct nand_chip *chip)
 
 	nand_set_manufacturer_data(chip, hynix);
 
+	if (!strncmp("H27UCG8T2ATR-BC", chip->parameters.model,
+		     sizeof("H27UCG8T2ATR-BC") - 1))
+		chip->ops.choose_interface_config =
+			h27ucg8t2atrbc_choose_interface_config;
+
 	ret = hynix_nand_rr_init(chip);
 	if (ret)
 		hynix_nand_cleanup(chip);
diff --git a/drivers/mtd/nand/raw/nand_ids.c b/drivers/mtd/nand/raw/nand_ids.c
index ba27902fc54b..b9945791a9d7 100644
--- a/drivers/mtd/nand/raw/nand_ids.c
+++ b/drivers/mtd/nand/raw/nand_ids.c
@@ -28,8 +28,7 @@ struct nand_flash_dev nand_flash_ids[] = {
 	 */
 	{"TC58NVG0S3E 1G 3.3V 8-bit",
 		{ .id = {0x98, 0xd1, 0x90, 0x15, 0x76, 0x14, 0x01, 0x00} },
-		  SZ_2K, SZ_128, SZ_128K, 0, 8, 64, NAND_ECC_INFO(1, SZ_512),
-		  2 },
+		  SZ_2K, SZ_128, SZ_128K, 0, 8, 64, NAND_ECC_INFO(1, SZ_512), },
 	{"TC58NVG2S0F 4G 3.3V 8-bit",
 		{ .id = {0x98, 0xdc, 0x90, 0x26, 0x76, 0x15, 0x01, 0x08} },
 		  SZ_4K, SZ_512, SZ_256K, 0, 8, 224, NAND_ECC_INFO(4, SZ_512) },
@@ -51,7 +50,10 @@ struct nand_flash_dev nand_flash_ids[] = {
 	{"H27UCG8T2ATR-BC 64G 3.3V 8-bit",
 		{ .id = {0xad, 0xde, 0x94, 0xda, 0x74, 0xc4} },
 		  SZ_8K, SZ_8K, SZ_2M, NAND_NEED_SCRAMBLING, 6, 640,
-		  NAND_ECC_INFO(40, SZ_1K), 4 },
+		  NAND_ECC_INFO(40, SZ_1K) },
+	{"TH58NVG2S3HBAI4 4G 3.3V 8-bit",
+		{ .id = {0x98, 0xdc, 0x91, 0x15, 0x76} },
+		  SZ_2K, SZ_512, SZ_128K, 0, 5, 128, NAND_ECC_INFO(8, SZ_512) },
 
 	LEGACY_ID_NAND("NAND 4MiB 5V 8-bit",   0x6B, 4, SZ_8K, SP_OPTIONS),
 	LEGACY_ID_NAND("NAND 4MiB 3,3V 8-bit", 0xE3, 4, SZ_8K, SP_OPTIONS),
@@ -166,7 +168,7 @@ struct nand_flash_dev nand_flash_ids[] = {
 };
 
 /* Manufacturer IDs */
-static const struct nand_manufacturer nand_manufacturers[] = {
+static const struct nand_manufacturer_desc nand_manufacturer_descs[] = {
 	{NAND_MFR_AMD, "AMD/Spansion", &amd_nand_manuf_ops},
 	{NAND_MFR_ATO, "ATO"},
 	{NAND_MFR_EON, "Eon"},
@@ -186,20 +188,20 @@ static const struct nand_manufacturer nand_manufacturers[] = {
 };
 
 /**
- * nand_get_manufacturer - Get manufacturer information from the manufacturer
- *			   ID
+ * nand_get_manufacturer_desc - Get manufacturer information from the
+ *                              manufacturer ID
  * @id: manufacturer ID
  *
- * Returns a pointer a nand_manufacturer object if the manufacturer is defined
+ * Returns a nand_manufacturer_desc object if the manufacturer is defined
  * in the NAND manufacturers database, NULL otherwise.
  */
-const struct nand_manufacturer *nand_get_manufacturer(u8 id)
+const struct nand_manufacturer_desc *nand_get_manufacturer_desc(u8 id)
 {
 	int i;
 
-	for (i = 0; i < ARRAY_SIZE(nand_manufacturers); i++)
-		if (nand_manufacturers[i].id == id)
-			return &nand_manufacturers[i];
+	for (i = 0; i < ARRAY_SIZE(nand_manufacturer_descs); i++)
+		if (nand_manufacturer_descs[i].id == id)
+			return &nand_manufacturer_descs[i];
 
 	return NULL;
 }
diff --git a/drivers/mtd/nand/raw/nand_legacy.c b/drivers/mtd/nand/raw/nand_legacy.c
index d64791c06a97..2bcc03714432 100644
--- a/drivers/mtd/nand/raw/nand_legacy.c
+++ b/drivers/mtd/nand/raw/nand_legacy.c
@@ -354,6 +354,9 @@ static void nand_command(struct nand_chip *chip, unsigned int command,
 
 static void nand_ccs_delay(struct nand_chip *chip)
 {
+	const struct nand_sdr_timings *sdr =
+		nand_get_sdr_timings(nand_get_interface_config(chip));
+
 	/*
 	 * The controller already takes care of waiting for tCCS when the RNDIN
 	 * or RNDOUT command is sent, return directly.
@@ -365,8 +368,8 @@ static void nand_ccs_delay(struct nand_chip *chip)
 	 * Wait tCCS_min if it is correctly defined, otherwise wait 500ns
 	 * (which should be safe for all NANDs).
 	 */
-	if (nand_has_setup_data_iface(chip))
-		ndelay(chip->data_interface.timings.sdr.tCCS_min / 1000);
+	if (nand_controller_can_setup_interface(chip))
+		ndelay(sdr->tCCS_min / 1000);
 	else
 		ndelay(500);
 }
diff --git a/drivers/mtd/nand/raw/nand_macronix.c b/drivers/mtd/nand/raw/nand_macronix.c
index 09c254c97b5c..1472f925f386 100644
--- a/drivers/mtd/nand/raw/nand_macronix.c
+++ b/drivers/mtd/nand/raw/nand_macronix.c
@@ -130,7 +130,7 @@ static void macronix_nand_onfi_init(struct nand_chip *chip)
 		return;
 
 	chip->read_retries = MACRONIX_NUM_READ_RETRY_MODES;
-	chip->setup_read_retry = macronix_nand_setup_read_retry;
+	chip->ops.setup_read_retry = macronix_nand_setup_read_retry;
 
 	if (p->supports_set_get_features) {
 		bitmap_set(p->set_feature_list,
@@ -242,8 +242,8 @@ static void macronix_nand_block_protection_support(struct nand_chip *chip)
 	bitmap_set(chip->parameters.set_feature_list,
 		   ONFI_FEATURE_ADDR_MXIC_PROTECTION, 1);
 
-	chip->lock_area = mxic_nand_lock;
-	chip->unlock_area = mxic_nand_unlock;
+	chip->ops.lock_area = mxic_nand_lock;
+	chip->ops.unlock_area = mxic_nand_unlock;
 }
 
 static int nand_power_down_op(struct nand_chip *chip)
@@ -312,8 +312,8 @@ static void macronix_nand_deep_power_down_support(struct nand_chip *chip)
 	if (i < 0)
 		return;
 
-	chip->suspend = mxic_nand_suspend;
-	chip->resume = mxic_nand_resume;
+	chip->ops.suspend = mxic_nand_suspend;
+	chip->ops.resume = mxic_nand_resume;
 }
 
 static int macronix_nand_init(struct nand_chip *chip)
diff --git a/drivers/mtd/nand/raw/nand_micron.c b/drivers/mtd/nand/raw/nand_micron.c
index 3589b4fce0d4..4385092a9325 100644
--- a/drivers/mtd/nand/raw/nand_micron.c
+++ b/drivers/mtd/nand/raw/nand_micron.c
@@ -84,7 +84,7 @@ static int micron_nand_onfi_init(struct nand_chip *chip)
 		struct nand_onfi_vendor_micron *micron = (void *)p->onfi->vendor;
 
 		chip->read_retries = micron->read_retry_options;
-		chip->setup_read_retry = micron_nand_setup_read_retry;
+		chip->ops.setup_read_retry = micron_nand_setup_read_retry;
 	}
 
 	if (p->supports_set_get_features) {
diff --git a/drivers/mtd/nand/raw/nand_timings.c b/drivers/mtd/nand/raw/nand_timings.c
index 36d21be3dfe5..94d832646487 100644
--- a/drivers/mtd/nand/raw/nand_timings.c
+++ b/drivers/mtd/nand/raw/nand_timings.c
@@ -12,7 +12,14 @@
 
 #define ONFI_DYN_TIMING_MAX U16_MAX
 
-static const struct nand_data_interface onfi_sdr_timings[] = {
+/*
+ * For non-ONFI chips we use the highest possible value for tPROG and tBERS.
+ * tR and tCCS will take the default values precised in the ONFI specification
+ * for timing mode 0, respectively 200us and 500ns.
+ *
+ * These four values are tweaked to be more accurate in the case of ONFI chips.
+ */
+static const struct nand_interface_config onfi_sdr_timings[] = {
 	/* Mode 0 */
 	{
 		.type = NAND_SDR_IFACE,
@@ -20,6 +27,8 @@ static const struct nand_data_interface onfi_sdr_timings[] = {
 		.timings.sdr = {
 			.tCCS_min = 500000,
 			.tR_max = 200000000,
+			.tPROG_max = 1000000ULL * ONFI_DYN_TIMING_MAX,
+			.tBERS_max = 1000000ULL * ONFI_DYN_TIMING_MAX,
 			.tADL_min = 400000,
 			.tALH_min = 20000,
 			.tALS_min = 50000,
@@ -63,6 +72,8 @@ static const struct nand_data_interface onfi_sdr_timings[] = {
 		.timings.sdr = {
 			.tCCS_min = 500000,
 			.tR_max = 200000000,
+			.tPROG_max = 1000000ULL * ONFI_DYN_TIMING_MAX,
+			.tBERS_max = 1000000ULL * ONFI_DYN_TIMING_MAX,
 			.tADL_min = 400000,
 			.tALH_min = 10000,
 			.tALS_min = 25000,
@@ -106,6 +117,8 @@ static const struct nand_data_interface onfi_sdr_timings[] = {
 		.timings.sdr = {
 			.tCCS_min = 500000,
 			.tR_max = 200000000,
+			.tPROG_max = 1000000ULL * ONFI_DYN_TIMING_MAX,
+			.tBERS_max = 1000000ULL * ONFI_DYN_TIMING_MAX,
 			.tADL_min = 400000,
 			.tALH_min = 10000,
 			.tALS_min = 15000,
@@ -149,6 +162,8 @@ static const struct nand_data_interface onfi_sdr_timings[] = {
 		.timings.sdr = {
 			.tCCS_min = 500000,
 			.tR_max = 200000000,
+			.tPROG_max = 1000000ULL * ONFI_DYN_TIMING_MAX,
+			.tBERS_max = 1000000ULL * ONFI_DYN_TIMING_MAX,
 			.tADL_min = 400000,
 			.tALH_min = 5000,
 			.tALS_min = 10000,
@@ -192,6 +207,8 @@ static const struct nand_data_interface onfi_sdr_timings[] = {
 		.timings.sdr = {
 			.tCCS_min = 500000,
 			.tR_max = 200000000,
+			.tPROG_max = 1000000ULL * ONFI_DYN_TIMING_MAX,
+			.tBERS_max = 1000000ULL * ONFI_DYN_TIMING_MAX,
 			.tADL_min = 400000,
 			.tALH_min = 5000,
 			.tALS_min = 10000,
@@ -235,6 +252,8 @@ static const struct nand_data_interface onfi_sdr_timings[] = {
 		.timings.sdr = {
 			.tCCS_min = 500000,
 			.tR_max = 200000000,
+			.tPROG_max = 1000000ULL * ONFI_DYN_TIMING_MAX,
+			.tBERS_max = 1000000ULL * ONFI_DYN_TIMING_MAX,
 			.tADL_min = 400000,
 			.tALH_min = 5000,
 			.tALS_min = 10000,
@@ -273,23 +292,79 @@ static const struct nand_data_interface onfi_sdr_timings[] = {
 	},
 };
 
+/* All NAND chips share the same reset data interface: SDR mode 0 */
+const struct nand_interface_config *nand_get_reset_interface_config(void)
+{
+	return &onfi_sdr_timings[0];
+}
+
+/**
+ * onfi_find_closest_sdr_mode - Derive the closest ONFI SDR timing mode given a
+ *                              set of timings
+ * @spec_timings: the timings to challenge
+ */
+unsigned int
+onfi_find_closest_sdr_mode(const struct nand_sdr_timings *spec_timings)
+{
+	const struct nand_sdr_timings *onfi_timings;
+	int mode;
+
+	for (mode = ARRAY_SIZE(onfi_sdr_timings) - 1; mode > 0; mode--) {
+		onfi_timings = &onfi_sdr_timings[mode].timings.sdr;
+
+		if (spec_timings->tCCS_min <= onfi_timings->tCCS_min &&
+		    spec_timings->tADL_min <= onfi_timings->tADL_min &&
+		    spec_timings->tALH_min <= onfi_timings->tALH_min &&
+		    spec_timings->tALS_min <= onfi_timings->tALS_min &&
+		    spec_timings->tAR_min <= onfi_timings->tAR_min &&
+		    spec_timings->tCEH_min <= onfi_timings->tCEH_min &&
+		    spec_timings->tCH_min <= onfi_timings->tCH_min &&
+		    spec_timings->tCLH_min <= onfi_timings->tCLH_min &&
+		    spec_timings->tCLR_min <= onfi_timings->tCLR_min &&
+		    spec_timings->tCLS_min <= onfi_timings->tCLS_min &&
+		    spec_timings->tCOH_min <= onfi_timings->tCOH_min &&
+		    spec_timings->tCS_min <= onfi_timings->tCS_min &&
+		    spec_timings->tDH_min <= onfi_timings->tDH_min &&
+		    spec_timings->tDS_min <= onfi_timings->tDS_min &&
+		    spec_timings->tIR_min <= onfi_timings->tIR_min &&
+		    spec_timings->tRC_min <= onfi_timings->tRC_min &&
+		    spec_timings->tREH_min <= onfi_timings->tREH_min &&
+		    spec_timings->tRHOH_min <= onfi_timings->tRHOH_min &&
+		    spec_timings->tRHW_min <= onfi_timings->tRHW_min &&
+		    spec_timings->tRLOH_min <= onfi_timings->tRLOH_min &&
+		    spec_timings->tRP_min <= onfi_timings->tRP_min &&
+		    spec_timings->tRR_min <= onfi_timings->tRR_min &&
+		    spec_timings->tWC_min <= onfi_timings->tWC_min &&
+		    spec_timings->tWH_min <= onfi_timings->tWH_min &&
+		    spec_timings->tWHR_min <= onfi_timings->tWHR_min &&
+		    spec_timings->tWP_min <= onfi_timings->tWP_min &&
+		    spec_timings->tWW_min <= onfi_timings->tWW_min)
+			return mode;
+	}
+
+	return 0;
+}
+
 /**
- * onfi_fill_data_interface - [NAND Interface] Initialize a data interface from
- * given ONFI mode
- * @mode: The ONFI timing mode
+ * onfi_fill_interface_config - Initialize an interface config from a given
+ *                              ONFI mode
+ * @chip: The NAND chip
+ * @iface: The interface configuration to fill
+ * @type: The interface type
+ * @timing_mode: The ONFI timing mode
  */
-int onfi_fill_data_interface(struct nand_chip *chip,
-			     enum nand_data_interface_type type,
-			     int timing_mode)
+void onfi_fill_interface_config(struct nand_chip *chip,
+				struct nand_interface_config *iface,
+				enum nand_interface_type type,
+				unsigned int timing_mode)
 {
-	struct nand_data_interface *iface = &chip->data_interface;
 	struct onfi_params *onfi = chip->parameters.onfi;
 
-	if (type != NAND_SDR_IFACE)
-		return -EINVAL;
+	if (WARN_ON(type != NAND_SDR_IFACE))
+		return;
 
-	if (timing_mode < 0 || timing_mode >= ARRAY_SIZE(onfi_sdr_timings))
-		return -EINVAL;
+	if (WARN_ON(timing_mode >= ARRAY_SIZE(onfi_sdr_timings)))
+		return;
 
 	*iface = onfi_sdr_timings[timing_mode];
 
@@ -308,22 +383,5 @@ int onfi_fill_data_interface(struct nand_chip *chip,
 
 		/* nanoseconds -> picoseconds */
 		timings->tCCS_min = 1000UL * onfi->tCCS;
-	} else {
-		struct nand_sdr_timings *timings = &iface->timings.sdr;
-		/*
-		 * For non-ONFI chips we use the highest possible value for
-		 * tPROG and tBERS. tR and tCCS will take the default values
-		 * precised in the ONFI specification for timing mode 0,
-		 * respectively 200us and 500ns.
-		 */
-
-		/* microseconds -> picoseconds */
-		timings->tPROG_max = 1000000ULL * ONFI_DYN_TIMING_MAX;
-		timings->tBERS_max = 1000000ULL * ONFI_DYN_TIMING_MAX;
-
-		timings->tR_max = 200000000;
-		timings->tCCS_min = 500000;
 	}
-
-	return 0;
 }
diff --git a/drivers/mtd/nand/raw/nand_toshiba.c b/drivers/mtd/nand/raw/nand_toshiba.c
index ae069905d7e4..f746c19f3b2c 100644
--- a/drivers/mtd/nand/raw/nand_toshiba.c
+++ b/drivers/mtd/nand/raw/nand_toshiba.c
@@ -33,7 +33,7 @@ static int toshiba_nand_benand_read_eccstatus_op(struct nand_chip *chip,
 
 	if (nand_has_exec_op(chip)) {
 		const struct nand_sdr_timings *sdr =
-			nand_get_sdr_timings(&chip->data_interface);
+			nand_get_sdr_timings(nand_get_interface_config(chip));
 		struct nand_op_instr instrs[] = {
 			NAND_OP_CMD(TOSHIBA_NAND_CMD_ECC_STATUS_READ,
 				    PSEC_TO_NSEC(sdr->tADL_min)),
@@ -194,17 +194,79 @@ static void toshiba_nand_decode_id(struct nand_chip *chip)
 	}
 }
 
+static int
+tc58teg5dclta00_choose_interface_config(struct nand_chip *chip,
+					struct nand_interface_config *iface)
+{
+	onfi_fill_interface_config(chip, iface, NAND_SDR_IFACE, 5);
+
+	return nand_choose_best_sdr_timings(chip, iface, NULL);
+}
+
+static int
+tc58nvg0s3e_choose_interface_config(struct nand_chip *chip,
+				    struct nand_interface_config *iface)
+{
+	onfi_fill_interface_config(chip, iface, NAND_SDR_IFACE, 2);
+
+	return nand_choose_best_sdr_timings(chip, iface, NULL);
+}
+
+static int
+th58nvg2s3hbai4_choose_interface_config(struct nand_chip *chip,
+					struct nand_interface_config *iface)
+{
+	struct nand_sdr_timings *sdr = &iface->timings.sdr;
+
+	/* Start with timings from the closest timing mode, mode 4. */
+	onfi_fill_interface_config(chip, iface, NAND_SDR_IFACE, 4);
+
+	/* Patch timings that differ from mode 4. */
+	sdr->tALS_min = 12000;
+	sdr->tCHZ_max = 20000;
+	sdr->tCLS_min = 12000;
+	sdr->tCOH_min = 0;
+	sdr->tDS_min = 12000;
+	sdr->tRHOH_min = 25000;
+	sdr->tRHW_min = 30000;
+	sdr->tRHZ_max = 60000;
+	sdr->tWHR_min = 60000;
+
+	/* Patch timings not part of onfi timing mode. */
+	sdr->tPROG_max = 700000000;
+	sdr->tBERS_max = 5000000000;
+
+	return nand_choose_best_sdr_timings(chip, iface, sdr);
+}
+
 static int tc58teg5dclta00_init(struct nand_chip *chip)
 {
 	struct mtd_info *mtd = nand_to_mtd(chip);
 
-	chip->onfi_timing_mode_default = 5;
+	chip->ops.choose_interface_config =
+		&tc58teg5dclta00_choose_interface_config;
 	chip->options |= NAND_NEED_SCRAMBLING;
 	mtd_set_pairing_scheme(mtd, &dist3_pairing_scheme);
 
 	return 0;
 }
 
+static int tc58nvg0s3e_init(struct nand_chip *chip)
+{
+	chip->ops.choose_interface_config =
+		&tc58nvg0s3e_choose_interface_config;
+
+	return 0;
+}
+
+static int th58nvg2s3hbai4_init(struct nand_chip *chip)
+{
+	chip->ops.choose_interface_config =
+		&th58nvg2s3hbai4_choose_interface_config;
+
+	return 0;
+}
+
 static int toshiba_nand_init(struct nand_chip *chip)
 {
 	if (nand_is_slc(chip))
@@ -217,6 +279,12 @@ static int toshiba_nand_init(struct nand_chip *chip)
 
 	if (!strcmp("TC58TEG5DCLTA00", chip->parameters.model))
 		tc58teg5dclta00_init(chip);
+	if (!strncmp("TC58NVG0S3E", chip->parameters.model,
+		     sizeof("TC58NVG0S3E") - 1))
+		tc58nvg0s3e_init(chip);
+	if (!strncmp("TH58NVG2S3HBAI4", chip->parameters.model,
+		     sizeof("TH58NVG2S3HBAI4") - 1))
+		th58nvg2s3hbai4_init(chip);
 
 	return 0;
 }
diff --git a/drivers/mtd/nand/raw/omap_elm.c b/drivers/mtd/nand/raw/omap_elm.c
index 078b1022ac2a..4b799521a427 100644
--- a/drivers/mtd/nand/raw/omap_elm.c
+++ b/drivers/mtd/nand/raw/omap_elm.c
@@ -2,7 +2,7 @@
 /*
  * Error Location Module
  *
- * Copyright (C) 2012 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2012 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #define DRIVER_NAME	"omap-elm"
diff --git a/drivers/mtd/nand/raw/qcom_nandc.c b/drivers/mtd/nand/raw/qcom_nandc.c
index f1daf330951b..bd7a7251429b 100644
--- a/drivers/mtd/nand/raw/qcom_nandc.c
+++ b/drivers/mtd/nand/raw/qcom_nandc.c
@@ -459,11 +459,13 @@ struct qcom_nand_host {
  * among different NAND controllers.
  * @ecc_modes - ecc mode for NAND
  * @is_bam - whether NAND controller is using BAM
+ * @is_qpic - whether NAND CTRL is part of qpic IP
  * @dev_cmd_reg_start - NAND_DEV_CMD_* registers starting offset
  */
 struct qcom_nandc_props {
 	u32 ecc_modes;
 	bool is_bam;
+	bool is_qpic;
 	u32 dev_cmd_reg_start;
 };
 
@@ -2774,14 +2776,24 @@ static int qcom_nandc_setup(struct qcom_nand_controller *nandc)
 	u32 nand_ctrl;
 
 	/* kill onenand */
-	nandc_write(nandc, SFLASHC_BURST_CFG, 0);
+	if (!nandc->props->is_qpic)
+		nandc_write(nandc, SFLASHC_BURST_CFG, 0);
 	nandc_write(nandc, dev_cmd_reg_addr(nandc, NAND_DEV_CMD_VLD),
 		    NAND_DEV_CMD_VLD_VAL);
 
 	/* enable ADM or BAM DMA */
 	if (nandc->props->is_bam) {
 		nand_ctrl = nandc_read(nandc, NAND_CTRL);
-		nandc_write(nandc, NAND_CTRL, nand_ctrl | BAM_MODE_EN);
+
+		/*
+		 *NAND_CTRL is an operational registers, and CPU
+		 * access to operational registers are read only
+		 * in BAM mode. So update the NAND_CTRL register
+		 * only if it is not in BAM mode. In most cases BAM
+		 * mode will be enabled in bootloader
+		 */
+		if (!(nand_ctrl & BAM_MODE_EN))
+			nandc_write(nandc, NAND_CTRL, nand_ctrl | BAM_MODE_EN);
 	} else {
 		nandc_write(nandc, NAND_FLASH_CHIP_SELECT, DM_EN);
 	}
@@ -3035,12 +3047,14 @@ static const struct qcom_nandc_props ipq806x_nandc_props = {
 static const struct qcom_nandc_props ipq4019_nandc_props = {
 	.ecc_modes = (ECC_BCH_4BIT | ECC_BCH_8BIT),
 	.is_bam = true,
+	.is_qpic = true,
 	.dev_cmd_reg_start = 0x0,
 };
 
 static const struct qcom_nandc_props ipq8074_nandc_props = {
 	.ecc_modes = (ECC_BCH_4BIT | ECC_BCH_8BIT),
 	.is_bam = true,
+	.is_qpic = true,
 	.dev_cmd_reg_start = 0x7000,
 };
 
diff --git a/drivers/mtd/nand/raw/s3c2410.c b/drivers/mtd/nand/raw/s3c2410.c
index d0dd0c446e4d..105522205979 100644
--- a/drivers/mtd/nand/raw/s3c2410.c
+++ b/drivers/mtd/nand/raw/s3c2410.c
@@ -808,8 +808,8 @@ static int s3c2410_nand_add_partition(struct s3c2410_nand_info *info,
 	return -ENODEV;
 }
 
-static int s3c2410_nand_setup_data_interface(struct nand_chip *chip, int csline,
-					const struct nand_data_interface *conf)
+static int s3c2410_nand_setup_interface(struct nand_chip *chip, int csline,
+					const struct nand_interface_config *conf)
 {
 	struct mtd_info *mtd = nand_to_mtd(chip);
 	struct s3c2410_nand_info *info = s3c2410_nand_mtd_toinfo(mtd);
@@ -999,7 +999,7 @@ static int s3c2410_nand_attach_chip(struct nand_chip *chip)
 
 static const struct nand_controller_ops s3c24xx_nand_controller_ops = {
 	.attach_chip = s3c2410_nand_attach_chip,
-	.setup_data_interface = s3c2410_nand_setup_data_interface,
+	.setup_interface = s3c2410_nand_setup_interface,
 };
 
 static const struct of_device_id s3c24xx_nand_dt_ids[] = {
diff --git a/drivers/mtd/nand/raw/stm32_fmc2_nand.c b/drivers/mtd/nand/raw/stm32_fmc2_nand.c
index 65c9d17b25a3..7f4546ae9130 100644
--- a/drivers/mtd/nand/raw/stm32_fmc2_nand.c
+++ b/drivers/mtd/nand/raw/stm32_fmc2_nand.c
@@ -11,10 +11,13 @@
 #include <linux/errno.h>
 #include <linux/interrupt.h>
 #include <linux/iopoll.h>
+#include <linux/mfd/syscon.h>
 #include <linux/module.h>
 #include <linux/mtd/rawnand.h>
+#include <linux/of_address.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
+#include <linux/regmap.h>
 #include <linux/reset.h>
 
 /* Bad block marker length */
@@ -242,7 +245,8 @@ struct stm32_fmc2_nfc {
 	struct nand_controller base;
 	struct stm32_fmc2_nand nand;
 	struct device *dev;
-	void __iomem *io_base;
+	struct device *cdev;
+	struct regmap *regmap;
 	void __iomem *data_base[FMC2_MAX_CE];
 	void __iomem *cmd_base[FMC2_MAX_CE];
 	void __iomem *addr_base[FMC2_MAX_CE];
@@ -277,40 +281,37 @@ static void stm32_fmc2_nfc_timings_init(struct nand_chip *chip)
 	struct stm32_fmc2_nfc *nfc = to_stm32_nfc(chip->controller);
 	struct stm32_fmc2_nand *nand = to_fmc2_nand(chip);
 	struct stm32_fmc2_timings *timings = &nand->timings;
-	u32 pcr = readl_relaxed(nfc->io_base + FMC2_PCR);
 	u32 pmem, patt;
 
 	/* Set tclr/tar timings */
-	pcr &= ~FMC2_PCR_TCLR;
-	pcr |= FIELD_PREP(FMC2_PCR_TCLR, timings->tclr);
-	pcr &= ~FMC2_PCR_TAR;
-	pcr |= FIELD_PREP(FMC2_PCR_TAR, timings->tar);
+	regmap_update_bits(nfc->regmap, FMC2_PCR,
+			   FMC2_PCR_TCLR | FMC2_PCR_TAR,
+			   FIELD_PREP(FMC2_PCR_TCLR, timings->tclr) |
+			   FIELD_PREP(FMC2_PCR_TAR, timings->tar));
 
 	/* Set tset/twait/thold/thiz timings in common bank */
 	pmem = FIELD_PREP(FMC2_PMEM_MEMSET, timings->tset_mem);
 	pmem |= FIELD_PREP(FMC2_PMEM_MEMWAIT, timings->twait);
 	pmem |= FIELD_PREP(FMC2_PMEM_MEMHOLD, timings->thold_mem);
 	pmem |= FIELD_PREP(FMC2_PMEM_MEMHIZ, timings->thiz);
+	regmap_write(nfc->regmap, FMC2_PMEM, pmem);
 
 	/* Set tset/twait/thold/thiz timings in attribut bank */
 	patt = FIELD_PREP(FMC2_PATT_ATTSET, timings->tset_att);
 	patt |= FIELD_PREP(FMC2_PATT_ATTWAIT, timings->twait);
 	patt |= FIELD_PREP(FMC2_PATT_ATTHOLD, timings->thold_att);
 	patt |= FIELD_PREP(FMC2_PATT_ATTHIZ, timings->thiz);
-
-	writel_relaxed(pcr, nfc->io_base + FMC2_PCR);
-	writel_relaxed(pmem, nfc->io_base + FMC2_PMEM);
-	writel_relaxed(patt, nfc->io_base + FMC2_PATT);
+	regmap_write(nfc->regmap, FMC2_PATT, patt);
 }
 
 static void stm32_fmc2_nfc_setup(struct nand_chip *chip)
 {
 	struct stm32_fmc2_nfc *nfc = to_stm32_nfc(chip->controller);
-	u32 pcr = readl_relaxed(nfc->io_base + FMC2_PCR);
+	u32 pcr = 0, pcr_mask;
 
 	/* Configure ECC algorithm (default configuration is Hamming) */
-	pcr &= ~FMC2_PCR_ECCALG;
-	pcr &= ~FMC2_PCR_BCHECC;
+	pcr_mask = FMC2_PCR_ECCALG;
+	pcr_mask |= FMC2_PCR_BCHECC;
 	if (chip->ecc.strength == FMC2_ECC_BCH8) {
 		pcr |= FMC2_PCR_ECCALG;
 		pcr |= FMC2_PCR_BCHECC;
@@ -319,15 +320,15 @@ static void stm32_fmc2_nfc_setup(struct nand_chip *chip)
 	}
 
 	/* Set buswidth */
-	pcr &= ~FMC2_PCR_PWID;
+	pcr_mask |= FMC2_PCR_PWID;
 	if (chip->options & NAND_BUSWIDTH_16)
 		pcr |= FIELD_PREP(FMC2_PCR_PWID, FMC2_PCR_PWID_BUSWIDTH_16);
 
 	/* Set ECC sector size */
-	pcr &= ~FMC2_PCR_ECCSS;
+	pcr_mask |= FMC2_PCR_ECCSS;
 	pcr |= FIELD_PREP(FMC2_PCR_ECCSS, FMC2_PCR_ECCSS_512);
 
-	writel_relaxed(pcr, nfc->io_base + FMC2_PCR);
+	regmap_update_bits(nfc->regmap, FMC2_PCR, pcr_mask, pcr);
 }
 
 static int stm32_fmc2_nfc_select_chip(struct nand_chip *chip, int chipnr)
@@ -393,81 +394,63 @@ static int stm32_fmc2_nfc_select_chip(struct nand_chip *chip, int chipnr)
 
 static void stm32_fmc2_nfc_set_buswidth_16(struct stm32_fmc2_nfc *nfc, bool set)
 {
-	u32 pcr = readl_relaxed(nfc->io_base + FMC2_PCR);
+	u32 pcr;
 
-	pcr &= ~FMC2_PCR_PWID;
-	if (set)
-		pcr |= FIELD_PREP(FMC2_PCR_PWID, FMC2_PCR_PWID_BUSWIDTH_16);
-	writel_relaxed(pcr, nfc->io_base + FMC2_PCR);
+	pcr = set ? FIELD_PREP(FMC2_PCR_PWID, FMC2_PCR_PWID_BUSWIDTH_16) :
+		    FIELD_PREP(FMC2_PCR_PWID, FMC2_PCR_PWID_BUSWIDTH_8);
+
+	regmap_update_bits(nfc->regmap, FMC2_PCR, FMC2_PCR_PWID, pcr);
 }
 
 static void stm32_fmc2_nfc_set_ecc(struct stm32_fmc2_nfc *nfc, bool enable)
 {
-	u32 pcr = readl(nfc->io_base + FMC2_PCR);
-
-	pcr &= ~FMC2_PCR_ECCEN;
-	if (enable)
-		pcr |= FMC2_PCR_ECCEN;
-	writel(pcr, nfc->io_base + FMC2_PCR);
+	regmap_update_bits(nfc->regmap, FMC2_PCR, FMC2_PCR_ECCEN,
+			   enable ? FMC2_PCR_ECCEN : 0);
 }
 
-static inline void stm32_fmc2_nfc_enable_seq_irq(struct stm32_fmc2_nfc *nfc)
+static void stm32_fmc2_nfc_enable_seq_irq(struct stm32_fmc2_nfc *nfc)
 {
-	u32 csqier = readl_relaxed(nfc->io_base + FMC2_CSQIER);
-
-	csqier |= FMC2_CSQIER_TCIE;
-
 	nfc->irq_state = FMC2_IRQ_SEQ;
 
-	writel_relaxed(csqier, nfc->io_base + FMC2_CSQIER);
+	regmap_update_bits(nfc->regmap, FMC2_CSQIER,
+			   FMC2_CSQIER_TCIE, FMC2_CSQIER_TCIE);
 }
 
-static inline void stm32_fmc2_nfc_disable_seq_irq(struct stm32_fmc2_nfc *nfc)
+static void stm32_fmc2_nfc_disable_seq_irq(struct stm32_fmc2_nfc *nfc)
 {
-	u32 csqier = readl_relaxed(nfc->io_base + FMC2_CSQIER);
-
-	csqier &= ~FMC2_CSQIER_TCIE;
-
-	writel_relaxed(csqier, nfc->io_base + FMC2_CSQIER);
+	regmap_update_bits(nfc->regmap, FMC2_CSQIER, FMC2_CSQIER_TCIE, 0);
 
 	nfc->irq_state = FMC2_IRQ_UNKNOWN;
 }
 
-static inline void stm32_fmc2_nfc_clear_seq_irq(struct stm32_fmc2_nfc *nfc)
+static void stm32_fmc2_nfc_clear_seq_irq(struct stm32_fmc2_nfc *nfc)
 {
-	writel_relaxed(FMC2_CSQICR_CLEAR_IRQ, nfc->io_base + FMC2_CSQICR);
+	regmap_write(nfc->regmap, FMC2_CSQICR, FMC2_CSQICR_CLEAR_IRQ);
 }
 
-static inline void stm32_fmc2_nfc_enable_bch_irq(struct stm32_fmc2_nfc *nfc,
-						 int mode)
+static void stm32_fmc2_nfc_enable_bch_irq(struct stm32_fmc2_nfc *nfc, int mode)
 {
-	u32 bchier = readl_relaxed(nfc->io_base + FMC2_BCHIER);
+	nfc->irq_state = FMC2_IRQ_BCH;
 
 	if (mode == NAND_ECC_WRITE)
-		bchier |= FMC2_BCHIER_EPBRIE;
+		regmap_update_bits(nfc->regmap, FMC2_BCHIER,
+				   FMC2_BCHIER_EPBRIE, FMC2_BCHIER_EPBRIE);
 	else
-		bchier |= FMC2_BCHIER_DERIE;
-
-	nfc->irq_state = FMC2_IRQ_BCH;
-
-	writel_relaxed(bchier, nfc->io_base + FMC2_BCHIER);
+		regmap_update_bits(nfc->regmap, FMC2_BCHIER,
+				   FMC2_BCHIER_DERIE, FMC2_BCHIER_DERIE);
 }
 
-static inline void stm32_fmc2_nfc_disable_bch_irq(struct stm32_fmc2_nfc *nfc)
+static void stm32_fmc2_nfc_disable_bch_irq(struct stm32_fmc2_nfc *nfc)
 {
-	u32 bchier = readl_relaxed(nfc->io_base + FMC2_BCHIER);
-
-	bchier &= ~FMC2_BCHIER_DERIE;
-	bchier &= ~FMC2_BCHIER_EPBRIE;
-
-	writel_relaxed(bchier, nfc->io_base + FMC2_BCHIER);
+	regmap_update_bits(nfc->regmap, FMC2_BCHIER,
+			   FMC2_BCHIER_DERIE | FMC2_BCHIER_EPBRIE, 0);
 
 	nfc->irq_state = FMC2_IRQ_UNKNOWN;
 }
 
-static inline void stm32_fmc2_nfc_clear_bch_irq(struct stm32_fmc2_nfc *nfc)
+static void stm32_fmc2_nfc_clear_bch_irq(struct stm32_fmc2_nfc *nfc)
 {
-	writel_relaxed(FMC2_BCHICR_CLEAR_IRQ, nfc->io_base + FMC2_BCHICR);
+	regmap_write(nfc->regmap, FMC2_BCHICR, FMC2_BCHICR_CLEAR_IRQ);
 }
 
 /*
@@ -481,13 +464,8 @@ static void stm32_fmc2_nfc_hwctl(struct nand_chip *chip, int mode)
 	stm32_fmc2_nfc_set_ecc(nfc, false);
 
 	if (chip->ecc.strength != FMC2_ECC_HAM) {
-		u32 pcr = readl_relaxed(nfc->io_base + FMC2_PCR);
-
-		if (mode == NAND_ECC_WRITE)
-			pcr |= FMC2_PCR_WEN;
-		else
-			pcr &= ~FMC2_PCR_WEN;
-		writel_relaxed(pcr, nfc->io_base + FMC2_PCR);
+		regmap_update_bits(nfc->regmap, FMC2_PCR, FMC2_PCR_WEN,
+				   mode == NAND_ECC_WRITE ? FMC2_PCR_WEN : 0);
 
 		reinit_completion(&nfc->complete);
 		stm32_fmc2_nfc_clear_bch_irq(nfc);
@@ -502,7 +480,7 @@ static void stm32_fmc2_nfc_hwctl(struct nand_chip *chip, int mode)
  * ECC is 3 bytes for 512 bytes of data (supports error correction up to
  * max of 1-bit)
  */
-static inline void stm32_fmc2_nfc_ham_set_ecc(const u32 ecc_sta, u8 *ecc)
+static void stm32_fmc2_nfc_ham_set_ecc(const u32 ecc_sta, u8 *ecc)
 {
 	ecc[0] = ecc_sta;
 	ecc[1] = ecc_sta >> 8;
@@ -516,15 +494,15 @@ static int stm32_fmc2_nfc_ham_calculate(struct nand_chip *chip, const u8 *data,
 	u32 sr, heccr;
 	int ret;
 
-	ret = readl_relaxed_poll_timeout(nfc->io_base + FMC2_SR,
-					 sr, sr & FMC2_SR_NWRF, 1,
-					 1000 * FMC2_TIMEOUT_MS);
+	ret = regmap_read_poll_timeout(nfc->regmap, FMC2_SR, sr,
+				       sr & FMC2_SR_NWRF, 1,
+				       1000 * FMC2_TIMEOUT_MS);
 	if (ret) {
 		dev_err(nfc->dev, "ham timeout\n");
 		return ret;
 	}
 
-	heccr = readl_relaxed(nfc->io_base + FMC2_HECCR);
+	regmap_read(nfc->regmap, FMC2_HECCR, &heccr);
 	stm32_fmc2_nfc_ham_set_ecc(heccr, ecc);
 	stm32_fmc2_nfc_set_ecc(nfc, false);
 
@@ -603,13 +581,13 @@ static int stm32_fmc2_nfc_bch_calculate(struct nand_chip *chip, const u8 *data,
 	}
 
 	/* Read parity bits */
-	bchpbr = readl_relaxed(nfc->io_base + FMC2_BCHPBR1);
+	regmap_read(nfc->regmap, FMC2_BCHPBR1, &bchpbr);
 	ecc[0] = bchpbr;
 	ecc[1] = bchpbr >> 8;
 	ecc[2] = bchpbr >> 16;
 	ecc[3] = bchpbr >> 24;
 
-	bchpbr = readl_relaxed(nfc->io_base + FMC2_BCHPBR2);
+	regmap_read(nfc->regmap, FMC2_BCHPBR2, &bchpbr);
 	ecc[4] = bchpbr;
 	ecc[5] = bchpbr >> 8;
 	ecc[6] = bchpbr >> 16;
@@ -617,13 +595,13 @@ static int stm32_fmc2_nfc_bch_calculate(struct nand_chip *chip, const u8 *data,
 	if (chip->ecc.strength == FMC2_ECC_BCH8) {
 		ecc[7] = bchpbr >> 24;
 
-		bchpbr = readl_relaxed(nfc->io_base + FMC2_BCHPBR3);
+		regmap_read(nfc->regmap, FMC2_BCHPBR3, &bchpbr);
 		ecc[8] = bchpbr;
 		ecc[9] = bchpbr >> 8;
 		ecc[10] = bchpbr >> 16;
 		ecc[11] = bchpbr >> 24;
 
-		bchpbr = readl_relaxed(nfc->io_base + FMC2_BCHPBR4);
+		regmap_read(nfc->regmap, FMC2_BCHPBR4, &bchpbr);
 		ecc[12] = bchpbr;
 	}
 
@@ -685,11 +663,7 @@ static int stm32_fmc2_nfc_bch_correct(struct nand_chip *chip, u8 *dat,
 		return -ETIMEDOUT;
 	}
 
-	ecc_sta[0] = readl_relaxed(nfc->io_base + FMC2_BCHDSR0);
-	ecc_sta[1] = readl_relaxed(nfc->io_base + FMC2_BCHDSR1);
-	ecc_sta[2] = readl_relaxed(nfc->io_base + FMC2_BCHDSR2);
-	ecc_sta[3] = readl_relaxed(nfc->io_base + FMC2_BCHDSR3);
-	ecc_sta[4] = readl_relaxed(nfc->io_base + FMC2_BCHDSR4);
+	regmap_bulk_read(nfc->regmap, FMC2_BCHDSR0, ecc_sta, 5);
 
 	stm32_fmc2_nfc_set_ecc(nfc, false);
 
@@ -764,30 +738,29 @@ static void stm32_fmc2_nfc_rw_page_init(struct nand_chip *chip, int page,
 {
 	struct stm32_fmc2_nfc *nfc = to_stm32_nfc(chip->controller);
 	struct mtd_info *mtd = nand_to_mtd(chip);
-	u32 csqcfgr1, csqcfgr2, csqcfgr3;
-	u32 csqar1, csqar2;
 	u32 ecc_offset = mtd->writesize + FMC2_BBM_LEN;
-	u32 pcr = readl_relaxed(nfc->io_base + FMC2_PCR);
+	/*
+	 * cfg[0] => csqcfgr1, cfg[1] => csqcfgr2, cfg[2] => csqcfgr3
+	 * cfg[3] => csqar1, cfg[4] => csqar2
+	 */
+	u32 cfg[5];
 
-	if (write_data)
-		pcr |= FMC2_PCR_WEN;
-	else
-		pcr &= ~FMC2_PCR_WEN;
-	writel_relaxed(pcr, nfc->io_base + FMC2_PCR);
+	regmap_update_bits(nfc->regmap, FMC2_PCR, FMC2_PCR_WEN,
+			   write_data ? FMC2_PCR_WEN : 0);
 
 	/*
 	 * - Set Program Page/Page Read command
 	 * - Enable DMA request data
 	 * - Set timings
 	 */
-	csqcfgr1 = FMC2_CSQCFGR1_DMADEN | FMC2_CSQCFGR1_CMD1T;
+	cfg[0] = FMC2_CSQCFGR1_DMADEN | FMC2_CSQCFGR1_CMD1T;
 	if (write_data)
-		csqcfgr1 |= FIELD_PREP(FMC2_CSQCFGR1_CMD1, NAND_CMD_SEQIN);
+		cfg[0] |= FIELD_PREP(FMC2_CSQCFGR1_CMD1, NAND_CMD_SEQIN);
 	else
-		csqcfgr1 |= FIELD_PREP(FMC2_CSQCFGR1_CMD1, NAND_CMD_READ0) |
-			    FMC2_CSQCFGR1_CMD2EN |
-			    FIELD_PREP(FMC2_CSQCFGR1_CMD2, NAND_CMD_READSTART) |
-			    FMC2_CSQCFGR1_CMD2T;
+		cfg[0] |= FIELD_PREP(FMC2_CSQCFGR1_CMD1, NAND_CMD_READ0) |
+			  FMC2_CSQCFGR1_CMD2EN |
+			  FIELD_PREP(FMC2_CSQCFGR1_CMD2, NAND_CMD_READSTART) |
+			  FMC2_CSQCFGR1_CMD2T;
 
 	/*
 	 * - Set Random Data Input/Random Data Read command
@@ -796,30 +769,29 @@ static void stm32_fmc2_nfc_rw_page_init(struct nand_chip *chip, int page,
 	 * - Set timings
 	 */
 	if (write_data)
-		csqcfgr2 = FIELD_PREP(FMC2_CSQCFGR2_RCMD1, NAND_CMD_RNDIN);
+		cfg[1] = FIELD_PREP(FMC2_CSQCFGR2_RCMD1, NAND_CMD_RNDIN);
 	else
-		csqcfgr2 = FIELD_PREP(FMC2_CSQCFGR2_RCMD1, NAND_CMD_RNDOUT) |
-			   FMC2_CSQCFGR2_RCMD2EN |
-			   FIELD_PREP(FMC2_CSQCFGR2_RCMD2,
-				      NAND_CMD_RNDOUTSTART) |
-			   FMC2_CSQCFGR2_RCMD1T |
-			   FMC2_CSQCFGR2_RCMD2T;
+		cfg[1] = FIELD_PREP(FMC2_CSQCFGR2_RCMD1, NAND_CMD_RNDOUT) |
+			 FMC2_CSQCFGR2_RCMD2EN |
+			 FIELD_PREP(FMC2_CSQCFGR2_RCMD2, NAND_CMD_RNDOUTSTART) |
+			 FMC2_CSQCFGR2_RCMD1T |
+			 FMC2_CSQCFGR2_RCMD2T;
 	if (!raw) {
-		csqcfgr2 |= write_data ? 0 : FMC2_CSQCFGR2_DMASEN;
-		csqcfgr2 |= FMC2_CSQCFGR2_SQSDTEN;
+		cfg[1] |= write_data ? 0 : FMC2_CSQCFGR2_DMASEN;
+		cfg[1] |= FMC2_CSQCFGR2_SQSDTEN;
 	}
 
 	/*
 	 * - Set the number of sectors to be written
 	 * - Set timings
 	 */
-	csqcfgr3 = FIELD_PREP(FMC2_CSQCFGR3_SNBR, chip->ecc.steps - 1);
+	cfg[2] = FIELD_PREP(FMC2_CSQCFGR3_SNBR, chip->ecc.steps - 1);
 	if (write_data) {
-		csqcfgr3 |= FMC2_CSQCFGR3_RAC2T;
+		cfg[2] |= FMC2_CSQCFGR3_RAC2T;
 		if (chip->options & NAND_ROW_ADDR_3)
-			csqcfgr3 |= FMC2_CSQCFGR3_AC5T;
+			cfg[2] |= FMC2_CSQCFGR3_AC5T;
 		else
-			csqcfgr3 |= FMC2_CSQCFGR3_AC4T;
+			cfg[2] |= FMC2_CSQCFGR3_AC4T;
 	}
 
 	/*
@@ -827,8 +799,8 @@ static void stm32_fmc2_nfc_rw_page_init(struct nand_chip *chip, int page,
 	 * Byte 1 and byte 2 => column, we start at 0x0
 	 * Byte 3 and byte 4 => page
 	 */
-	csqar1 = FIELD_PREP(FMC2_CSQCAR1_ADDC3, page);
-	csqar1 |= FIELD_PREP(FMC2_CSQCAR1_ADDC4, page >> 8);
+	cfg[3] = FIELD_PREP(FMC2_CSQCAR1_ADDC3, page);
+	cfg[3] |= FIELD_PREP(FMC2_CSQCAR1_ADDC4, page >> 8);
 
 	/*
 	 * - Set chip enable number
@@ -836,23 +808,19 @@ static void stm32_fmc2_nfc_rw_page_init(struct nand_chip *chip, int page,
 	 * - Calculate the number of address cycles to be issued
 	 * - Set byte 5 of address cycle if needed
 	 */
-	csqar2 = FIELD_PREP(FMC2_CSQCAR2_NANDCEN, nfc->cs_sel);
+	cfg[4] = FIELD_PREP(FMC2_CSQCAR2_NANDCEN, nfc->cs_sel);
 	if (chip->options & NAND_BUSWIDTH_16)
-		csqar2 |= FIELD_PREP(FMC2_CSQCAR2_SAO, ecc_offset >> 1);
+		cfg[4] |= FIELD_PREP(FMC2_CSQCAR2_SAO, ecc_offset >> 1);
 	else
-		csqar2 |= FIELD_PREP(FMC2_CSQCAR2_SAO, ecc_offset);
+		cfg[4] |= FIELD_PREP(FMC2_CSQCAR2_SAO, ecc_offset);
 	if (chip->options & NAND_ROW_ADDR_3) {
-		csqcfgr1 |= FIELD_PREP(FMC2_CSQCFGR1_ACYNBR, 5);
-		csqar2 |= FIELD_PREP(FMC2_CSQCAR2_ADDC5, page >> 16);
+		cfg[0] |= FIELD_PREP(FMC2_CSQCFGR1_ACYNBR, 5);
+		cfg[4] |= FIELD_PREP(FMC2_CSQCAR2_ADDC5, page >> 16);
 	} else {
-		csqcfgr1 |= FIELD_PREP(FMC2_CSQCFGR1_ACYNBR, 4);
+		cfg[0] |= FIELD_PREP(FMC2_CSQCFGR1_ACYNBR, 4);
 	}
 
-	writel_relaxed(csqcfgr1, nfc->io_base + FMC2_CSQCFGR1);
-	writel_relaxed(csqcfgr2, nfc->io_base + FMC2_CSQCFGR2);
-	writel_relaxed(csqcfgr3, nfc->io_base + FMC2_CSQCFGR3);
-	writel_relaxed(csqar1, nfc->io_base + FMC2_CSQAR1);
-	writel_relaxed(csqar2, nfc->io_base + FMC2_CSQAR2);
+	regmap_bulk_write(nfc->regmap, FMC2_CSQCFGR1, cfg, 5);
 }
 
 static void stm32_fmc2_nfc_dma_callback(void *arg)
@@ -870,7 +838,6 @@ static int stm32_fmc2_nfc_xfer(struct nand_chip *chip, const u8 *buf,
 	struct dma_chan *dma_ch = nfc->dma_rx_ch;
 	enum dma_data_direction dma_data_dir = DMA_FROM_DEVICE;
 	enum dma_transfer_direction dma_transfer_dir = DMA_DEV_TO_MEM;
-	u32 csqcr = readl_relaxed(nfc->io_base + FMC2_CSQCR);
 	int eccsteps = chip->ecc.steps;
 	int eccsize = chip->ecc.size;
 	unsigned long timeout = msecs_to_jiffies(FMC2_TIMEOUT_MS);
@@ -948,8 +915,8 @@ static int stm32_fmc2_nfc_xfer(struct nand_chip *chip, const u8 *buf,
 	stm32_fmc2_nfc_enable_seq_irq(nfc);
 
 	/* Start the transfer */
-	csqcr |= FMC2_CSQCR_CSQSTART;
-	writel_relaxed(csqcr, nfc->io_base + FMC2_CSQCR);
+	regmap_update_bits(nfc->regmap, FMC2_CSQCR,
+			   FMC2_CSQCR_CSQSTART, FMC2_CSQCR_CSQSTART);
 
 	/* Wait end of sequencer transfer */
 	if (!wait_for_completion_timeout(&nfc->complete, timeout)) {
@@ -1042,11 +1009,13 @@ static int stm32_fmc2_nfc_seq_write_page_raw(struct nand_chip *chip,
 }
 
 /* Get a status indicating which sectors have errors */
-static inline u16 stm32_fmc2_nfc_get_mapping_status(struct stm32_fmc2_nfc *nfc)
+static u16 stm32_fmc2_nfc_get_mapping_status(struct stm32_fmc2_nfc *nfc)
 {
-	u32 csqemsr = readl_relaxed(nfc->io_base + FMC2_CSQEMSR);
+	u32 csqemsr;
 
-	return csqemsr & FMC2_CSQEMSR_SEM;
+	regmap_read(nfc->regmap, FMC2_CSQEMSR, &csqemsr);
+
+	return FIELD_GET(FMC2_CSQEMSR_SEM, csqemsr);
 }
 
 static int stm32_fmc2_nfc_seq_correct(struct nand_chip *chip, u8 *dat,
@@ -1302,22 +1271,22 @@ static int stm32_fmc2_nfc_waitrdy(struct nand_chip *chip,
 	u32 isr, sr;
 
 	/* Check if there is no pending requests to the NAND flash */
-	if (readl_relaxed_poll_timeout_atomic(nfc->io_base + FMC2_SR, sr,
-					      sr & FMC2_SR_NWRF, 1,
-					      1000 * FMC2_TIMEOUT_MS))
+	if (regmap_read_poll_timeout(nfc->regmap, FMC2_SR, sr,
+				     sr & FMC2_SR_NWRF, 1,
+				     1000 * FMC2_TIMEOUT_MS))
 		dev_warn(nfc->dev, "Waitrdy timeout\n");
 
 	/* Wait tWB before R/B# signal is low */
-	timings = nand_get_sdr_timings(&chip->data_interface);
+	timings = nand_get_sdr_timings(nand_get_interface_config(chip));
 	ndelay(PSEC_TO_NSEC(timings->tWB_max));
 
 	/* R/B# signal is low, clear high level flag */
-	writel_relaxed(FMC2_ICR_CIHLF, nfc->io_base + FMC2_ICR);
+	regmap_write(nfc->regmap, FMC2_ICR, FMC2_ICR_CIHLF);
 
 	/* Wait R/B# signal is high */
-	return readl_relaxed_poll_timeout_atomic(nfc->io_base + FMC2_ISR,
-						 isr, isr & FMC2_ISR_IHLF,
-						 5, 1000 * timeout_ms);
+	return regmap_read_poll_timeout(nfc->regmap, FMC2_ISR, isr,
+					isr & FMC2_ISR_IHLF, 5,
+					1000 * FMC2_TIMEOUT_MS);
 }
 
 static int stm32_fmc2_nfc_exec_op(struct nand_chip *chip,
@@ -1375,8 +1344,9 @@ static int stm32_fmc2_nfc_exec_op(struct nand_chip *chip,
 
 static void stm32_fmc2_nfc_init(struct stm32_fmc2_nfc *nfc)
 {
-	u32 pcr = readl_relaxed(nfc->io_base + FMC2_PCR);
-	u32 bcr1 = readl_relaxed(nfc->io_base + FMC2_BCR1);
+	u32 pcr;
+
+	regmap_read(nfc->regmap, FMC2_PCR, &pcr);
 
 	/* Set CS used to undefined */
 	nfc->cs_sel = -1;
@@ -1407,12 +1377,13 @@ static void stm32_fmc2_nfc_init(struct stm32_fmc2_nfc *nfc)
 	pcr |= FIELD_PREP(FMC2_PCR_TAR, FMC2_PCR_TAR_DEFAULT);
 
 	/* Enable FMC2 controller */
-	bcr1 |= FMC2_BCR1_FMC2EN;
+	if (nfc->dev == nfc->cdev)
+		regmap_update_bits(nfc->regmap, FMC2_BCR1,
+				   FMC2_BCR1_FMC2EN, FMC2_BCR1_FMC2EN);
 
-	writel_relaxed(bcr1, nfc->io_base + FMC2_BCR1);
-	writel_relaxed(pcr, nfc->io_base + FMC2_PCR);
-	writel_relaxed(FMC2_PMEM_DEFAULT, nfc->io_base + FMC2_PMEM);
-	writel_relaxed(FMC2_PATT_DEFAULT, nfc->io_base + FMC2_PATT);
+	regmap_write(nfc->regmap, FMC2_PCR, pcr);
+	regmap_write(nfc->regmap, FMC2_PMEM, FMC2_PMEM_DEFAULT);
+	regmap_write(nfc->regmap, FMC2_PATT, FMC2_PATT_DEFAULT);
 }
 
 static void stm32_fmc2_nfc_calc_timings(struct nand_chip *chip,
@@ -1546,7 +1517,7 @@ static void stm32_fmc2_nfc_calc_timings(struct nand_chip *chip,
 }
 
 static int stm32_fmc2_nfc_setup_interface(struct nand_chip *chip, int chipnr,
-					  const struct nand_data_interface *conf)
+					  const struct nand_interface_config *conf)
 {
 	const struct nand_sdr_timings *sdrt;
 
@@ -1570,7 +1541,7 @@ static int stm32_fmc2_nfc_dma_setup(struct stm32_fmc2_nfc *nfc)
 	nfc->dma_tx_ch = dma_request_chan(nfc->dev, "tx");
 	if (IS_ERR(nfc->dma_tx_ch)) {
 		ret = PTR_ERR(nfc->dma_tx_ch);
-		if (ret != -ENODEV)
+		if (ret != -ENODEV && ret != -EPROBE_DEFER)
 			dev_err(nfc->dev,
 				"failed to request tx DMA channel: %d\n", ret);
 		nfc->dma_tx_ch = NULL;
@@ -1580,7 +1551,7 @@ static int stm32_fmc2_nfc_dma_setup(struct stm32_fmc2_nfc *nfc)
 	nfc->dma_rx_ch = dma_request_chan(nfc->dev, "rx");
 	if (IS_ERR(nfc->dma_rx_ch)) {
 		ret = PTR_ERR(nfc->dma_rx_ch);
-		if (ret != -ENODEV)
+		if (ret != -ENODEV && ret != -EPROBE_DEFER)
 			dev_err(nfc->dev,
 				"failed to request rx DMA channel: %d\n", ret);
 		nfc->dma_rx_ch = NULL;
@@ -1590,7 +1561,7 @@ static int stm32_fmc2_nfc_dma_setup(struct stm32_fmc2_nfc *nfc)
 	nfc->dma_ecc_ch = dma_request_chan(nfc->dev, "ecc");
 	if (IS_ERR(nfc->dma_ecc_ch)) {
 		ret = PTR_ERR(nfc->dma_ecc_ch);
-		if (ret != -ENODEV)
+		if (ret != -ENODEV && ret != -EPROBE_DEFER)
 			dev_err(nfc->dev,
 				"failed to request ecc DMA channel: %d\n", ret);
 		nfc->dma_ecc_ch = NULL;
@@ -1764,7 +1735,7 @@ static int stm32_fmc2_nfc_attach_chip(struct nand_chip *chip)
 static const struct nand_controller_ops stm32_fmc2_nfc_controller_ops = {
 	.attach_chip = stm32_fmc2_nfc_attach_chip,
 	.exec_op = stm32_fmc2_nfc_exec_op,
-	.setup_data_interface = stm32_fmc2_nfc_setup_interface,
+	.setup_interface = stm32_fmc2_nfc_setup_interface,
 };
 
 static int stm32_fmc2_nfc_parse_child(struct stm32_fmc2_nfc *nfc,
@@ -1838,6 +1809,33 @@ static int stm32_fmc2_nfc_parse_dt(struct stm32_fmc2_nfc *nfc)
 	return ret;
 }
 
+static int stm32_fmc2_nfc_set_cdev(struct stm32_fmc2_nfc *nfc)
+{
+	struct device *dev = nfc->dev;
+	bool ebi_found = false;
+
+	if (dev->parent && of_device_is_compatible(dev->parent->of_node,
+						   "st,stm32mp1-fmc2-ebi"))
+		ebi_found = true;
+
+	if (of_device_is_compatible(dev->of_node, "st,stm32mp1-fmc2-nfc")) {
+		if (ebi_found) {
+			nfc->cdev = dev->parent;
+
+			return 0;
+		}
+
+		return -EINVAL;
+	}
+
+	if (ebi_found)
+		return -EINVAL;
+
+	nfc->cdev = dev;
+
+	return 0;
+}
+
 static int stm32_fmc2_nfc_probe(struct platform_device *pdev)
 {
 	struct device *dev = &pdev->dev;
@@ -1847,7 +1845,9 @@ static int stm32_fmc2_nfc_probe(struct platform_device *pdev)
 	struct resource *res;
 	struct mtd_info *mtd;
 	struct nand_chip *chip;
+	struct resource cres;
 	int chip_cs, mem_region, ret, irq;
+	int start_region = 0;
 
 	nfc = devm_kzalloc(dev, sizeof(*nfc), GFP_KERNEL);
 	if (!nfc)
@@ -1857,18 +1857,28 @@ static int stm32_fmc2_nfc_probe(struct platform_device *pdev)
 	nand_controller_init(&nfc->base);
 	nfc->base.ops = &stm32_fmc2_nfc_controller_ops;
 
+	ret = stm32_fmc2_nfc_set_cdev(nfc);
+	if (ret)
+		return ret;
+
 	ret = stm32_fmc2_nfc_parse_dt(nfc);
 	if (ret)
 		return ret;
 
-	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-	nfc->io_base = devm_ioremap_resource(dev, res);
-	if (IS_ERR(nfc->io_base))
-		return PTR_ERR(nfc->io_base);
+	ret = of_address_to_resource(nfc->cdev->of_node, 0, &cres);
+	if (ret)
+		return ret;
+
+	nfc->io_phys_addr = cres.start;
+
+	nfc->regmap = device_node_to_regmap(nfc->cdev->of_node);
+	if (IS_ERR(nfc->regmap))
+		return PTR_ERR(nfc->regmap);
 
-	nfc->io_phys_addr = res->start;
+	if (nfc->dev == nfc->cdev)
+		start_region = 1;
 
-	for (chip_cs = 0, mem_region = 1; chip_cs < FMC2_MAX_CE;
+	for (chip_cs = 0, mem_region = start_region; chip_cs < FMC2_MAX_CE;
 	     chip_cs++, mem_region += 3) {
 		if (!(nfc->cs_assigned & BIT(chip_cs)))
 			continue;
@@ -1906,7 +1916,7 @@ static int stm32_fmc2_nfc_probe(struct platform_device *pdev)
 
 	init_completion(&nfc->complete);
 
-	nfc->clk = devm_clk_get(dev, NULL);
+	nfc->clk = devm_clk_get(nfc->cdev, NULL);
 	if (IS_ERR(nfc->clk))
 		return PTR_ERR(nfc->clk);
 
@@ -2047,6 +2057,7 @@ static SIMPLE_DEV_PM_OPS(stm32_fmc2_nfc_pm_ops, stm32_fmc2_nfc_suspend,
 
 static const struct of_device_id stm32_fmc2_nfc_match[] = {
 	{.compatible = "st,stm32mp15-fmc2"},
+	{.compatible = "st,stm32mp1-fmc2-nfc"},
 	{}
 };
 MODULE_DEVICE_TABLE(of, stm32_fmc2_nfc_match);
diff --git a/drivers/mtd/nand/raw/sunxi_nand.c b/drivers/mtd/nand/raw/sunxi_nand.c
index ffbc1651fadc..9c50c2b965e1 100644
--- a/drivers/mtd/nand/raw/sunxi_nand.c
+++ b/drivers/mtd/nand/raw/sunxi_nand.c
@@ -1376,8 +1376,8 @@ static int _sunxi_nand_lookup_timing(const s32 *lut, int lut_size, u32 duration,
 #define sunxi_nand_lookup_timing(l, p, c) \
 			_sunxi_nand_lookup_timing(l, ARRAY_SIZE(l), p, c)
 
-static int sunxi_nfc_setup_data_interface(struct nand_chip *nand, int csline,
-					const struct nand_data_interface *conf)
+static int sunxi_nfc_setup_interface(struct nand_chip *nand, int csline,
+				     const struct nand_interface_config *conf)
 {
 	struct sunxi_nand_chip *sunxi_nand = to_sunxi_nand(nand);
 	struct sunxi_nfc *nfc = to_sunxi_nfc(sunxi_nand->nand.controller);
@@ -1920,7 +1920,7 @@ static int sunxi_nfc_exec_op(struct nand_chip *nand,
 
 static const struct nand_controller_ops sunxi_nand_controller_ops = {
 	.attach_chip = sunxi_nand_attach_chip,
-	.setup_data_interface = sunxi_nfc_setup_data_interface,
+	.setup_interface = sunxi_nfc_setup_interface,
 	.exec_op = sunxi_nfc_exec_op,
 };
 
diff --git a/drivers/mtd/nand/raw/tango_nand.c b/drivers/mtd/nand/raw/tango_nand.c
index 246871e01027..bdb965ae7a4a 100644
--- a/drivers/mtd/nand/raw/tango_nand.c
+++ b/drivers/mtd/nand/raw/tango_nand.c
@@ -113,59 +113,80 @@ struct tango_chip {
 
 #define TIMING(t0, t1, t2, t3) ((t0) << 24 | (t1) << 16 | (t2) << 8 | (t3))
 
-static void tango_cmd_ctrl(struct nand_chip *chip, int dat, unsigned int ctrl)
+static void tango_select_target(struct nand_chip *chip, unsigned int cs)
 {
+	struct tango_nfc *nfc = to_tango_nfc(chip->controller);
 	struct tango_chip *tchip = to_tango_chip(chip);
 
-	if (ctrl & NAND_CLE)
-		writeb_relaxed(dat, tchip->base + PBUS_CMD);
-
-	if (ctrl & NAND_ALE)
-		writeb_relaxed(dat, tchip->base + PBUS_ADDR);
+	writel_relaxed(tchip->timing1, nfc->reg_base + NFC_TIMING1);
+	writel_relaxed(tchip->timing2, nfc->reg_base + NFC_TIMING2);
+	writel_relaxed(tchip->xfer_cfg, nfc->reg_base + NFC_XFER_CFG);
+	writel_relaxed(tchip->pkt_0_cfg, nfc->reg_base + NFC_PKT_0_CFG);
+	writel_relaxed(tchip->pkt_n_cfg, nfc->reg_base + NFC_PKT_N_CFG);
+	writel_relaxed(tchip->bb_cfg, nfc->reg_base + NFC_BB_CFG);
 }
 
-static int tango_dev_ready(struct nand_chip *chip)
+static int tango_waitrdy(struct nand_chip *chip, unsigned int timeout_ms)
 {
 	struct tango_nfc *nfc = to_tango_nfc(chip->controller);
+	u32 status;
 
-	return readl_relaxed(nfc->pbus_base + PBUS_CS_CTRL) & PBUS_IORDY;
+	return readl_relaxed_poll_timeout(nfc->pbus_base + PBUS_CS_CTRL,
+					  status, status & PBUS_IORDY, 20,
+					  timeout_ms);
 }
 
-static u8 tango_read_byte(struct nand_chip *chip)
+static int tango_exec_instr(struct nand_chip *chip,
+			    const struct nand_op_instr *instr)
 {
 	struct tango_chip *tchip = to_tango_chip(chip);
+	unsigned int i;
 
-	return readb_relaxed(tchip->base + PBUS_DATA);
-}
-
-static void tango_read_buf(struct nand_chip *chip, u8 *buf, int len)
-{
-	struct tango_chip *tchip = to_tango_chip(chip);
+	switch (instr->type) {
+	case NAND_OP_CMD_INSTR:
+		writeb_relaxed(instr->ctx.cmd.opcode, tchip->base + PBUS_CMD);
+		return 0;
+	case NAND_OP_ADDR_INSTR:
+		for (i = 0; i < instr->ctx.addr.naddrs; i++)
+			writeb_relaxed(instr->ctx.addr.addrs[i],
+				       tchip->base + PBUS_ADDR);
+		return 0;
+	case NAND_OP_DATA_IN_INSTR:
+		ioread8_rep(tchip->base + PBUS_DATA, instr->ctx.data.buf.in,
+			    instr->ctx.data.len);
+		return 0;
+	case NAND_OP_DATA_OUT_INSTR:
+		iowrite8_rep(tchip->base + PBUS_DATA, instr->ctx.data.buf.out,
+			     instr->ctx.data.len);
+		return 0;
+	case NAND_OP_WAITRDY_INSTR:
+		return tango_waitrdy(chip,
+				     instr->ctx.waitrdy.timeout_ms);
+	default:
+		break;
+	}
 
-	ioread8_rep(tchip->base + PBUS_DATA, buf, len);
+	return -EINVAL;
 }
 
-static void tango_write_buf(struct nand_chip *chip, const u8 *buf, int len)
+static int tango_exec_op(struct nand_chip *chip,
+			 const struct nand_operation *op,
+			 bool check_only)
 {
-	struct tango_chip *tchip = to_tango_chip(chip);
-
-	iowrite8_rep(tchip->base + PBUS_DATA, buf, len);
-}
+	unsigned int i;
+	int ret = 0;
 
-static void tango_select_chip(struct nand_chip *chip, int idx)
-{
-	struct tango_nfc *nfc = to_tango_nfc(chip->controller);
-	struct tango_chip *tchip = to_tango_chip(chip);
+	if (check_only)
+		return 0;
 
-	if (idx < 0)
-		return; /* No "chip unselect" function */
+	tango_select_target(chip, op->cs);
+	for (i = 0; i < op->ninstrs; i++) {
+		ret = tango_exec_instr(chip, &op->instrs[i]);
+		if (ret)
+			break;
+	}
 
-	writel_relaxed(tchip->timing1, nfc->reg_base + NFC_TIMING1);
-	writel_relaxed(tchip->timing2, nfc->reg_base + NFC_TIMING2);
-	writel_relaxed(tchip->xfer_cfg, nfc->reg_base + NFC_XFER_CFG);
-	writel_relaxed(tchip->pkt_0_cfg, nfc->reg_base + NFC_PKT_0_CFG);
-	writel_relaxed(tchip->pkt_n_cfg, nfc->reg_base + NFC_PKT_N_CFG);
-	writel_relaxed(tchip->bb_cfg, nfc->reg_base + NFC_BB_CFG);
+	return ret;
 }
 
 /*
@@ -279,6 +300,7 @@ static int tango_read_page(struct nand_chip *chip, u8 *buf,
 	struct tango_nfc *nfc = to_tango_nfc(chip->controller);
 	int err, res, len = mtd->writesize;
 
+	tango_select_target(chip, chip->cur_cs);
 	if (oob_required)
 		chip->ecc.read_oob(chip, page);
 
@@ -300,22 +322,30 @@ static int tango_write_page(struct nand_chip *chip, const u8 *buf,
 {
 	struct mtd_info *mtd = nand_to_mtd(chip);
 	struct tango_nfc *nfc = to_tango_nfc(chip->controller);
-	int err, status, len = mtd->writesize;
+	const struct nand_sdr_timings *timings;
+	int err, len = mtd->writesize;
+	u8 status;
 
 	/* Calling tango_write_oob() would send PAGEPROG twice */
 	if (oob_required)
 		return -ENOTSUPP;
 
+	tango_select_target(chip, chip->cur_cs);
 	writel_relaxed(0xffffffff, nfc->mem_base + METADATA);
 	err = do_dma(nfc, DMA_TO_DEVICE, NFC_WRITE, buf, len, page);
 	if (err)
 		return err;
 
-	status = chip->legacy.waitfunc(chip);
-	if (status & NAND_STATUS_FAIL)
-		return -EIO;
+	timings = nand_get_sdr_timings(nand_get_interface_config(chip));
+	err = tango_waitrdy(chip, PSEC_TO_MSEC(timings->tR_max));
+	if (err)
+		return err;
 
-	return 0;
+	err = nand_status_op(chip, &status);
+	if (err)
+		return err;
+
+	return (status & NAND_STATUS_FAIL) ? -EIO : 0;
 }
 
 static void aux_read(struct nand_chip *chip, u8 **buf, int len, int *pos)
@@ -326,7 +356,9 @@ static void aux_read(struct nand_chip *chip, u8 **buf, int len, int *pos)
 		/* skip over "len" bytes */
 		nand_change_read_column_op(chip, *pos, NULL, 0, false);
 	} else {
-		tango_read_buf(chip, *buf, len);
+		struct tango_chip *tchip = to_tango_chip(chip);
+
+		ioread8_rep(tchip->base + PBUS_DATA, *buf, len);
 		*buf += len;
 	}
 }
@@ -339,7 +371,9 @@ static void aux_write(struct nand_chip *chip, const u8 **buf, int len, int *pos)
 		/* skip over "len" bytes */
 		nand_change_write_column_op(chip, *pos, NULL, 0, false);
 	} else {
-		tango_write_buf(chip, *buf, len);
+		struct tango_chip *tchip = to_tango_chip(chip);
+
+		iowrite8_rep(tchip->base + PBUS_DATA, *buf, len);
 		*buf += len;
 	}
 }
@@ -420,6 +454,7 @@ static void raw_write(struct nand_chip *chip, const u8 *buf, const u8 *oob)
 static int tango_read_page_raw(struct nand_chip *chip, u8 *buf,
 			       int oob_required, int page)
 {
+	tango_select_target(chip, chip->cur_cs);
 	nand_read_page_op(chip, page, 0, NULL, 0);
 	raw_read(chip, buf, chip->oob_poi);
 	return 0;
@@ -428,6 +463,7 @@ static int tango_read_page_raw(struct nand_chip *chip, u8 *buf,
 static int tango_write_page_raw(struct nand_chip *chip, const u8 *buf,
 				int oob_required, int page)
 {
+	tango_select_target(chip, chip->cur_cs);
 	nand_prog_page_begin_op(chip, page, 0, NULL, 0);
 	raw_write(chip, buf, chip->oob_poi);
 	return nand_prog_page_end_op(chip);
@@ -435,6 +471,7 @@ static int tango_write_page_raw(struct nand_chip *chip, const u8 *buf,
 
 static int tango_read_oob(struct nand_chip *chip, int page)
 {
+	tango_select_target(chip, chip->cur_cs);
 	nand_read_page_op(chip, page, 0, NULL, 0);
 	raw_read(chip, NULL, chip->oob_poi);
 	return 0;
@@ -442,6 +479,7 @@ static int tango_read_oob(struct nand_chip *chip, int page)
 
 static int tango_write_oob(struct nand_chip *chip, int page)
 {
+	tango_select_target(chip, chip->cur_cs);
 	nand_prog_page_begin_op(chip, page, 0, NULL, 0);
 	raw_write(chip, NULL, chip->oob_poi);
 	return nand_prog_page_end_op(chip);
@@ -477,7 +515,7 @@ static u32 to_ticks(int kHz, int ps)
 }
 
 static int tango_set_timings(struct nand_chip *chip, int csline,
-			     const struct nand_data_interface *conf)
+			     const struct nand_interface_config *conf)
 {
 	const struct nand_sdr_timings *sdr = nand_get_sdr_timings(conf);
 	struct tango_nfc *nfc = to_tango_nfc(chip->controller);
@@ -527,7 +565,8 @@ static int tango_attach_chip(struct nand_chip *chip)
 
 static const struct nand_controller_ops tango_controller_ops = {
 	.attach_chip = tango_attach_chip,
-	.setup_data_interface = tango_set_timings,
+	.setup_interface = tango_set_timings,
+	.exec_op = tango_exec_op,
 };
 
 static int chip_init(struct device *dev, struct device_node *np)
@@ -562,12 +601,6 @@ static int chip_init(struct device *dev, struct device_node *np)
 	ecc = &chip->ecc;
 	mtd = nand_to_mtd(chip);
 
-	chip->legacy.read_byte = tango_read_byte;
-	chip->legacy.write_buf = tango_write_buf;
-	chip->legacy.read_buf = tango_read_buf;
-	chip->legacy.select_chip = tango_select_chip;
-	chip->legacy.cmd_ctrl = tango_cmd_ctrl;
-	chip->legacy.dev_ready = tango_dev_ready;
 	chip->options = NAND_USES_DMA |
 			NAND_NO_SUBPAGE_WRITE |
 			NAND_WAIT_TCCS;
diff --git a/drivers/mtd/nand/raw/tegra_nand.c b/drivers/mtd/nand/raw/tegra_nand.c
index f9d046b2cd3b..6b6212ffa01c 100644
--- a/drivers/mtd/nand/raw/tegra_nand.c
+++ b/drivers/mtd/nand/raw/tegra_nand.c
@@ -813,8 +813,8 @@ static void tegra_nand_setup_timing(struct tegra_nand_controller *ctrl,
 	writel_relaxed(reg, ctrl->regs + TIMING_2);
 }
 
-static int tegra_nand_setup_data_interface(struct nand_chip *chip, int csline,
-					const struct nand_data_interface *conf)
+static int tegra_nand_setup_interface(struct nand_chip *chip, int csline,
+				      const struct nand_interface_config *conf)
 {
 	struct tegra_nand_controller *ctrl = to_tegra_ctrl(chip->controller);
 	const struct nand_sdr_timings *timings;
@@ -1053,7 +1053,7 @@ static int tegra_nand_attach_chip(struct nand_chip *chip)
 static const struct nand_controller_ops tegra_nand_controller_ops = {
 	.attach_chip = &tegra_nand_attach_chip,
 	.exec_op = tegra_nand_exec_op,
-	.setup_data_interface = tegra_nand_setup_data_interface,
+	.setup_interface = tegra_nand_setup_interface,
 };
 
 static int tegra_nand_chips_init(struct device *dev,
diff --git a/drivers/mtd/parsers/bcm63xxpart.c b/drivers/mtd/parsers/bcm63xxpart.c
index 78f90c6c18fd..b15bdadaedb5 100644
--- a/drivers/mtd/parsers/bcm63xxpart.c
+++ b/drivers/mtd/parsers/bcm63xxpart.c
@@ -22,6 +22,11 @@
 #include <linux/mtd/partitions.h>
 #include <linux/of.h>
 
+#ifdef CONFIG_MIPS
+#include <asm/bootinfo.h>
+#include <asm/fw/cfe/cfe_api.h>
+#endif /* CONFIG_MIPS */
+
 #define BCM963XX_CFE_BLOCK_SIZE		SZ_64K	/* always at least 64KiB */
 
 #define BCM963XX_CFE_MAGIC_OFFSET	0x4e0
@@ -32,28 +37,15 @@
 #define STR_NULL_TERMINATE(x) \
 	do { char *_str = (x); _str[sizeof(x) - 1] = 0; } while (0)
 
-static int bcm63xx_detect_cfe(struct mtd_info *master)
+static inline int bcm63xx_detect_cfe(void)
 {
-	char buf[9];
-	int ret;
-	size_t retlen;
+	int ret = 0;
 
-	ret = mtd_read(master, BCM963XX_CFE_VERSION_OFFSET, 5, &retlen,
-		       (void *)buf);
-	buf[retlen] = 0;
+#ifdef CONFIG_MIPS
+	ret = (fw_arg3 == CFE_EPTSEAL);
+#endif /* CONFIG_MIPS */
 
-	if (ret)
-		return ret;
-
-	if (strncmp("cfe-v", buf, 5) == 0)
-		return 0;
-
-	/* very old CFE's do not have the cfe-v string, so check for magic */
-	ret = mtd_read(master, BCM963XX_CFE_MAGIC_OFFSET, 8, &retlen,
-		       (void *)buf);
-	buf[retlen] = 0;
-
-	return strncmp("CFE1CFE1", buf, 8);
+	return ret;
 }
 
 static int bcm63xx_read_nvram(struct mtd_info *master,
@@ -138,7 +130,7 @@ static int bcm63xx_parse_cfe_partitions(struct mtd_info *master,
 	struct bcm963xx_nvram *nvram = NULL;
 	int ret;
 
-	if (bcm63xx_detect_cfe(master))
+	if (!bcm63xx_detect_cfe())
 		return -EINVAL;
 
 	nvram = vzalloc(sizeof(*nvram));
diff --git a/drivers/mtd/spi-nor/controllers/intel-spi-pci.c b/drivers/mtd/spi-nor/controllers/intel-spi-pci.c
index 81329f680bec..c72aa1ab71ad 100644
--- a/drivers/mtd/spi-nor/controllers/intel-spi-pci.c
+++ b/drivers/mtd/spi-nor/controllers/intel-spi-pci.c
@@ -68,7 +68,9 @@ static const struct pci_device_id intel_spi_pci_ids[] = {
 	{ PCI_VDEVICE(INTEL, 0x06a4), (unsigned long)&bxt_info },
 	{ PCI_VDEVICE(INTEL, 0x18e0), (unsigned long)&bxt_info },
 	{ PCI_VDEVICE(INTEL, 0x19e0), (unsigned long)&bxt_info },
+	{ PCI_VDEVICE(INTEL, 0x1bca), (unsigned long)&bxt_info },
 	{ PCI_VDEVICE(INTEL, 0x34a4), (unsigned long)&bxt_info },
+	{ PCI_VDEVICE(INTEL, 0x43a4), (unsigned long)&cnl_info },
 	{ PCI_VDEVICE(INTEL, 0x4b24), (unsigned long)&bxt_info },
 	{ PCI_VDEVICE(INTEL, 0x4da4), (unsigned long)&bxt_info },
 	{ PCI_VDEVICE(INTEL, 0xa0a4), (unsigned long)&bxt_info },
diff --git a/drivers/mtd/spi-nor/controllers/intel-spi.c b/drivers/mtd/spi-nor/controllers/intel-spi.c
index 61d2a0ad2131..b54a56a68100 100644
--- a/drivers/mtd/spi-nor/controllers/intel-spi.c
+++ b/drivers/mtd/spi-nor/controllers/intel-spi.c
@@ -292,7 +292,7 @@ static int intel_spi_wait_hw_busy(struct intel_spi *ispi)
 	u32 val;
 
 	return readl_poll_timeout(ispi->base + HSFSTS_CTL, val,
-				  !(val & HSFSTS_CTL_SCIP), 40,
+				  !(val & HSFSTS_CTL_SCIP), 0,
 				  INTEL_SPI_TIMEOUT * 1000);
 }
 
@@ -301,7 +301,7 @@ static int intel_spi_wait_sw_busy(struct intel_spi *ispi)
 	u32 val;
 
 	return readl_poll_timeout(ispi->sregs + SSFSTS_CTL, val,
-				  !(val & SSFSTS_CTL_SCIP), 40,
+				  !(val & SSFSTS_CTL_SCIP), 0,
 				  INTEL_SPI_TIMEOUT * 1000);
 }
 
@@ -612,6 +612,15 @@ static int intel_spi_write_reg(struct spi_nor *nor, u8 opcode, const u8 *buf,
 		return 0;
 	}
 
+	/*
+	 * We hope that HW sequencer will do the right thing automatically and
+	 * with the SW sequencer we cannot use preopcode anyway, so just ignore
+	 * the Write Disable operation and pretend it was completed
+	 * successfully.
+	 */
+	if (opcode == SPINOR_OP_WRDI)
+		return 0;
+
 	writel(0, ispi->base + FADDR);
 
 	/* Write the value beforehand */
diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
index 0369d98b2d12..65eff4ce6ab1 100644
--- a/drivers/mtd/spi-nor/core.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -1907,15 +1907,16 @@ static int spi_nor_is_locked(struct mtd_info *mtd, loff_t ofs, uint64_t len)
 }
 
 /**
- * spi_nor_sr1_bit6_quad_enable() - Set the Quad Enable BIT(6) in the Status
- * Register 1.
+ * spi_nor_sr1_bit6_quad_enable() - Set/Unset the Quad Enable BIT(6) in the
+ *                                  Status Register 1.
  * @nor:	pointer to a 'struct spi_nor'
+ * @enable:	true to enable Quad mode, false to disable Quad mode.
  *
  * Bit 6 of the Status Register 1 is the QE bit for Macronix like QSPI memories.
  *
  * Return: 0 on success, -errno otherwise.
  */
-int spi_nor_sr1_bit6_quad_enable(struct spi_nor *nor)
+int spi_nor_sr1_bit6_quad_enable(struct spi_nor *nor, bool enable)
 {
 	int ret;
 
@@ -1923,45 +1924,56 @@ int spi_nor_sr1_bit6_quad_enable(struct spi_nor *nor)
 	if (ret)
 		return ret;
 
-	if (nor->bouncebuf[0] & SR1_QUAD_EN_BIT6)
+	if ((enable && (nor->bouncebuf[0] & SR1_QUAD_EN_BIT6)) ||
+	    (!enable && !(nor->bouncebuf[0] & SR1_QUAD_EN_BIT6)))
 		return 0;
 
-	nor->bouncebuf[0] |= SR1_QUAD_EN_BIT6;
+	if (enable)
+		nor->bouncebuf[0] |= SR1_QUAD_EN_BIT6;
+	else
+		nor->bouncebuf[0] &= ~SR1_QUAD_EN_BIT6;
 
 	return spi_nor_write_sr1_and_check(nor, nor->bouncebuf[0]);
 }
 
 /**
- * spi_nor_sr2_bit1_quad_enable() - set the Quad Enable BIT(1) in the Status
- * Register 2.
+ * spi_nor_sr2_bit1_quad_enable() - set/unset the Quad Enable BIT(1) in the
+ *                                  Status Register 2.
  * @nor:       pointer to a 'struct spi_nor'.
+ * @enable:	true to enable Quad mode, false to disable Quad mode.
  *
  * Bit 1 of the Status Register 2 is the QE bit for Spansion like QSPI memories.
  *
  * Return: 0 on success, -errno otherwise.
  */
-int spi_nor_sr2_bit1_quad_enable(struct spi_nor *nor)
+int spi_nor_sr2_bit1_quad_enable(struct spi_nor *nor, bool enable)
 {
 	int ret;
 
 	if (nor->flags & SNOR_F_NO_READ_CR)
-		return spi_nor_write_16bit_cr_and_check(nor, SR2_QUAD_EN_BIT1);
+		return spi_nor_write_16bit_cr_and_check(nor,
+						enable ? SR2_QUAD_EN_BIT1 : 0);
 
 	ret = spi_nor_read_cr(nor, nor->bouncebuf);
 	if (ret)
 		return ret;
 
-	if (nor->bouncebuf[0] & SR2_QUAD_EN_BIT1)
+	if ((enable && (nor->bouncebuf[0] & SR2_QUAD_EN_BIT1)) ||
+	    (!enable && !(nor->bouncebuf[0] & SR2_QUAD_EN_BIT1)))
 		return 0;
 
-	nor->bouncebuf[0] |= SR2_QUAD_EN_BIT1;
+	if (enable)
+		nor->bouncebuf[0] |= SR2_QUAD_EN_BIT1;
+	else
+		nor->bouncebuf[0] &= ~SR2_QUAD_EN_BIT1;
 
 	return spi_nor_write_16bit_cr_and_check(nor, nor->bouncebuf[0]);
 }
 
 /**
- * spi_nor_sr2_bit7_quad_enable() - set QE bit in Status Register 2.
+ * spi_nor_sr2_bit7_quad_enable() - set/unset QE bit in Status Register 2.
  * @nor:	pointer to a 'struct spi_nor'
+ * @enable:	true to enable Quad mode, false to disable Quad mode.
  *
  * Set the Quad Enable (QE) bit in the Status Register 2.
  *
@@ -1971,7 +1983,7 @@ int spi_nor_sr2_bit1_quad_enable(struct spi_nor *nor)
  *
  * Return: 0 on success, -errno otherwise.
  */
-int spi_nor_sr2_bit7_quad_enable(struct spi_nor *nor)
+int spi_nor_sr2_bit7_quad_enable(struct spi_nor *nor, bool enable)
 {
 	u8 *sr2 = nor->bouncebuf;
 	int ret;
@@ -1981,11 +1993,15 @@ int spi_nor_sr2_bit7_quad_enable(struct spi_nor *nor)
 	ret = spi_nor_read_sr2(nor, sr2);
 	if (ret)
 		return ret;
-	if (*sr2 & SR2_QUAD_EN_BIT7)
+	if ((enable && (*sr2 & SR2_QUAD_EN_BIT7)) ||
+	    (!enable && !(*sr2 & SR2_QUAD_EN_BIT7)))
 		return 0;
 
 	/* Update the Quad Enable bit. */
-	*sr2 |= SR2_QUAD_EN_BIT7;
+	if (enable)
+		*sr2 |= SR2_QUAD_EN_BIT7;
+	else
+		*sr2 &= ~SR2_QUAD_EN_BIT7;
 
 	ret = spi_nor_write_sr2(nor, sr2);
 	if (ret)
@@ -2898,12 +2914,13 @@ static int spi_nor_init_params(struct spi_nor *nor)
 }
 
 /**
- * spi_nor_quad_enable() - enable Quad I/O if needed.
+ * spi_nor_quad_enable() - enable/disable Quad I/O if needed.
  * @nor:                pointer to a 'struct spi_nor'
+ * @enable:             true to enable Quad mode. false to disable Quad mode.
  *
  * Return: 0 on success, -errno otherwise.
  */
-static int spi_nor_quad_enable(struct spi_nor *nor)
+static int spi_nor_quad_enable(struct spi_nor *nor, bool enable)
 {
 	if (!nor->params->quad_enable)
 		return 0;
@@ -2912,7 +2929,7 @@ static int spi_nor_quad_enable(struct spi_nor *nor)
 	      spi_nor_get_protocol_width(nor->write_proto) == 4))
 		return 0;
 
-	return nor->params->quad_enable(nor);
+	return nor->params->quad_enable(nor, enable);
 }
 
 /**
@@ -2936,7 +2953,7 @@ static int spi_nor_init(struct spi_nor *nor)
 {
 	int err;
 
-	err = spi_nor_quad_enable(nor);
+	err = spi_nor_quad_enable(nor, true);
 	if (err) {
 		dev_dbg(nor->dev, "quad mode not supported\n");
 		return err;
@@ -2983,6 +3000,8 @@ void spi_nor_restore(struct spi_nor *nor)
 	if (nor->addr_width == 4 && !(nor->flags & SNOR_F_4B_OPCODES) &&
 	    nor->flags & SNOR_F_BROKEN_RESET)
 		nor->params->set_4byte_addr_mode(nor, false);
+
+	spi_nor_quad_enable(nor, false);
 }
 EXPORT_SYMBOL_GPL(spi_nor_restore);
 
diff --git a/drivers/mtd/spi-nor/core.h b/drivers/mtd/spi-nor/core.h
index 6f2f6b27173f..95aa32f3ceb1 100644
--- a/drivers/mtd/spi-nor/core.h
+++ b/drivers/mtd/spi-nor/core.h
@@ -198,7 +198,7 @@ struct spi_nor_locking_ops {
  *                      higher index in the array, the higher priority.
  * @erase_map:		the erase map parsed from the SFDP Sector Map Parameter
  *                      Table.
- * @quad_enable:	enables SPI NOR quad mode.
+ * @quad_enable:	enables/disables SPI NOR Quad mode.
  * @set_4byte_addr_mode: puts the SPI NOR in 4 byte addressing mode.
  * @convert_addr:	converts an absolute address into something the flash
  *                      will understand. Particularly useful when pagesize is
@@ -219,7 +219,7 @@ struct spi_nor_flash_parameter {
 
 	struct spi_nor_erase_map        erase_map;
 
-	int (*quad_enable)(struct spi_nor *nor);
+	int (*quad_enable)(struct spi_nor *nor, bool enable);
 	int (*set_4byte_addr_mode)(struct spi_nor *nor, bool enable);
 	u32 (*convert_addr)(struct spi_nor *nor, u32 addr);
 	int (*setup)(struct spi_nor *nor, const struct spi_nor_hwcaps *hwcaps);
@@ -406,9 +406,9 @@ int spi_nor_write_ear(struct spi_nor *nor, u8 ear);
 int spi_nor_wait_till_ready(struct spi_nor *nor);
 int spi_nor_lock_and_prep(struct spi_nor *nor);
 void spi_nor_unlock_and_unprep(struct spi_nor *nor);
-int spi_nor_sr1_bit6_quad_enable(struct spi_nor *nor);
-int spi_nor_sr2_bit1_quad_enable(struct spi_nor *nor);
-int spi_nor_sr2_bit7_quad_enable(struct spi_nor *nor);
+int spi_nor_sr1_bit6_quad_enable(struct spi_nor *nor, bool enable);
+int spi_nor_sr2_bit1_quad_enable(struct spi_nor *nor, bool enable);
+int spi_nor_sr2_bit7_quad_enable(struct spi_nor *nor, bool enable);
 
 int spi_nor_xread_sr(struct spi_nor *nor, u8 *sr);
 ssize_t spi_nor_read_data(struct spi_nor *nor, loff_t from, size_t len,
diff --git a/drivers/mtd/spi-nor/macronix.c b/drivers/mtd/spi-nor/macronix.c
index 96735d83c77c..f97f3d127575 100644
--- a/drivers/mtd/spi-nor/macronix.c
+++ b/drivers/mtd/spi-nor/macronix.c
@@ -52,6 +52,9 @@ static const struct flash_info macronix_parts[] = {
 	{ "mx25u6435f",  INFO(0xc22537, 0, 64 * 1024, 128, SECT_4K) },
 	{ "mx25l12805d", INFO(0xc22018, 0, 64 * 1024, 256, 0) },
 	{ "mx25l12855e", INFO(0xc22618, 0, 64 * 1024, 256, 0) },
+	{ "mx25r1635f",  INFO(0xc22815, 0, 64 * 1024,  32,
+			      SECT_4K | SPI_NOR_DUAL_READ |
+			      SPI_NOR_QUAD_READ) },
 	{ "mx25r3235f",  INFO(0xc22816, 0, 64 * 1024,  64,
 			      SECT_4K | SPI_NOR_DUAL_READ |
 			      SPI_NOR_QUAD_READ) },
@@ -84,6 +87,9 @@ static const struct flash_info macronix_parts[] = {
 			      SPI_NOR_QUAD_READ) },
 	{ "mx66l1g55g",  INFO(0xc2261b, 0, 64 * 1024, 2048,
 			      SPI_NOR_QUAD_READ) },
+	{ "mx66u2g45g",	 INFO(0xc2253c, 0, 64 * 1024, 4096,
+			      SECT_4K | SPI_NOR_DUAL_READ |
+			      SPI_NOR_QUAD_READ | SPI_NOR_4B_OPCODES) },
 };
 
 static void macronix_default_init(struct spi_nor *nor)
diff --git a/drivers/mtd/spi-nor/micron-st.c b/drivers/mtd/spi-nor/micron-st.c
index 3dca5b9af3b6..ef3695080710 100644
--- a/drivers/mtd/spi-nor/micron-st.c
+++ b/drivers/mtd/spi-nor/micron-st.c
@@ -71,8 +71,8 @@ static const struct flash_info st_parts[] = {
 			      SECT_4K | USE_FSR | SPI_NOR_QUAD_READ |
 			      NO_CHIP_ERASE) },
 	{ "mt25qu02g",   INFO(0x20bb22, 0, 64 * 1024, 4096,
-			      SECT_4K | USE_FSR | SPI_NOR_QUAD_READ |
-			      NO_CHIP_ERASE) },
+			      SECT_4K | USE_FSR | SPI_NOR_DUAL_READ |
+			      SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
 
 	{ "m25p05",  INFO(0x202010,  0,  32 * 1024,   2, 0) },
 	{ "m25p10",  INFO(0x202011,  0,  32 * 1024,   4, 0) },
diff --git a/drivers/mtd/spi-nor/sfdp.c b/drivers/mtd/spi-nor/sfdp.c
index 55c0c508464b..e2a43d39eb5f 100644
--- a/drivers/mtd/spi-nor/sfdp.c
+++ b/drivers/mtd/spi-nor/sfdp.c
@@ -598,7 +598,8 @@ static int spi_nor_parse_bfpt(struct spi_nor *nor,
 		break;
 
 	default:
-		return -EINVAL;
+		dev_dbg(nor->dev, "BFPT QER reserved value used\n");
+		break;
 	}
 
 	/* Stop here if not JESD216 rev C or later. */
diff --git a/drivers/mtd/spi-nor/spansion.c b/drivers/mtd/spi-nor/spansion.c
index e550cd5c9d3a..8429b4af999a 100644
--- a/drivers/mtd/spi-nor/spansion.c
+++ b/drivers/mtd/spi-nor/spansion.c
@@ -64,7 +64,6 @@ static const struct flash_info spansion_parts[] = {
 	{ "s25fs512s",  INFO6(0x010220, 0x4d0081, 256 * 1024, 256,
 			      SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ | USE_CLSR)
 	  .fixups = &s25fs_s_fixups, },
-	{ "s70fl01gs",  INFO(0x010221, 0x4d00, 256 * 1024, 256, 0) },
 	{ "s25sl12800", INFO(0x012018, 0x0300, 256 * 1024,  64, 0) },
 	{ "s25sl12801", INFO(0x012018, 0x0301,  64 * 1024, 256, 0) },
 	{ "s25fl129p0", INFO(0x012018, 0x4d00, 256 * 1024,  64,
@@ -84,7 +83,8 @@ static const struct flash_info spansion_parts[] = {
 			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ "s25fl016k",  INFO(0xef4015,      0,  64 * 1024,  32,
 			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
-	{ "s25fl064k",  INFO(0xef4017,      0,  64 * 1024, 128, SECT_4K) },
+	{ "s25fl064k",  INFO(0xef4017,      0,  64 * 1024, 128,
+			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ "s25fl116k",  INFO(0x014015,      0,  64 * 1024,  32,
 			     SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ "s25fl132k",  INFO(0x014016,      0,  64 * 1024,  64, SECT_4K) },
diff --git a/drivers/mtd/spi-nor/winbond.c b/drivers/mtd/spi-nor/winbond.c
index 5062af10f138..6dcde15fb1aa 100644
--- a/drivers/mtd/spi-nor/winbond.c
+++ b/drivers/mtd/spi-nor/winbond.c
@@ -64,10 +64,12 @@ static const struct flash_info winbond_parts[] = {
 			    SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
 			    SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB) },
 	{ "w25x64", INFO(0xef3017, 0, 64 * 1024, 128, SECT_4K) },
-	{ "w25q64", INFO(0xef4017, 0, 64 * 1024, 128, SECT_4K) },
+	{ "w25q64", INFO(0xef4017, 0, 64 * 1024, 128,
+			 SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ "w25q64dw", INFO(0xef6017, 0, 64 * 1024, 128,
 			   SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
 			   SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB) },
+	{ "w25q64jvm", INFO(0xef7017, 0, 64 * 1024, 128, SECT_4K) },
 	{ "w25q128fw", INFO(0xef6018, 0, 64 * 1024, 256,
 			    SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
 			    SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB) },
diff --git a/include/linux/mtd/hyperbus.h b/include/linux/mtd/hyperbus.h
index 2dfe65964f6e..2129f7d3b6eb 100644
--- a/include/linux/mtd/hyperbus.h
+++ b/include/linux/mtd/hyperbus.h
@@ -1,6 +1,6 @@
 /* SPDX-License-Identifier: GPL-2.0
  *
- * Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+ * Copyright (C) 2019 Texas Instruments Incorporated - https://www.ti.com/
  */
 
 #ifndef __LINUX_MTD_HYPERBUS_H__
diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h
index 0c7483843a32..af99041ceaa9 100644
--- a/include/linux/mtd/nand.h
+++ b/include/linux/mtd/nand.h
@@ -12,6 +12,8 @@
 
 #include <linux/mtd/mtd.h>
 
+struct nand_device;
+
 /**
  * struct nand_memory_organization - Memory organization structure
  * @bits_per_cell: number of bits per NAND cell
@@ -114,11 +116,11 @@ struct nand_page_io_req {
 };
 
 /**
- * struct nand_ecc_req - NAND ECC requirements
+ * struct nand_ecc_props - NAND ECC properties
  * @strength: ECC strength
- * @step_size: ECC step/block size
+ * @step_size: Number of bytes per step
  */
-struct nand_ecc_req {
+struct nand_ecc_props {
 	unsigned int strength;
 	unsigned int step_size;
 };
@@ -133,8 +135,6 @@ struct nand_bbt {
 	unsigned long *cache;
 };
 
-struct nand_device;
-
 /**
  * struct nand_ops - NAND operations
  * @erase: erase a specific block. No need to check if the block is bad before
@@ -179,7 +179,7 @@ struct nand_ops {
 struct nand_device {
 	struct mtd_info mtd;
 	struct nand_memory_organization memorg;
-	struct nand_ecc_req eccreq;
+	struct nand_ecc_props eccreq;
 	struct nand_row_converter rowconv;
 	struct nand_bbt bbt;
 	const struct nand_ops *ops;
diff --git a/include/linux/mtd/pfow.h b/include/linux/mtd/pfow.h
index 122f3439e1af..6166e7c60869 100644
--- a/include/linux/mtd/pfow.h
+++ b/include/linux/mtd/pfow.h
@@ -19,7 +19,7 @@
 /* Identification info for LPDDR chip */
 #define PFOW_MANUFACTURER_ID			0x0020
 #define PFOW_DEVICE_ID				0x0022
-/* Address in PFOW where prog buffer can can be found */
+/* Address in PFOW where prog buffer can be found */
 #define PFOW_PROGRAM_BUFFER_OFFSET		0x0040
 /* Size of program buffer in words */
 #define PFOW_PROGRAM_BUFFER_SIZE		0x0042
diff --git a/include/linux/mtd/rawnand.h b/include/linux/mtd/rawnand.h
index 65b1c1c18b41..a725b620aca2 100644
--- a/include/linux/mtd/rawnand.h
+++ b/include/linux/mtd/rawnand.h
@@ -492,22 +492,22 @@ struct nand_sdr_timings {
 };
 
 /**
- * enum nand_data_interface_type - NAND interface timing type
+ * enum nand_interface_type - NAND interface type
  * @NAND_SDR_IFACE:	Single Data Rate interface
  */
-enum nand_data_interface_type {
+enum nand_interface_type {
 	NAND_SDR_IFACE,
 };
 
 /**
- * struct nand_data_interface - NAND interface timing
+ * struct nand_interface_config - NAND interface timing
  * @type:	 type of the timing
  * @timings:	 The timing information
  * @timings.mode: Timing mode as defined in the specification
  * @timings.sdr: Use it when @type is %NAND_SDR_IFACE.
  */
-struct nand_data_interface {
-	enum nand_data_interface_type type;
+struct nand_interface_config {
+	enum nand_interface_type type;
 	struct nand_timings {
 		unsigned int mode;
 		union {
@@ -521,7 +521,7 @@ struct nand_data_interface {
  * @conf:	The data interface
  */
 static inline const struct nand_sdr_timings *
-nand_get_sdr_timings(const struct nand_data_interface *conf)
+nand_get_sdr_timings(const struct nand_interface_config *conf)
 {
 	if (conf->type != NAND_SDR_IFACE)
 		return ERR_PTR(-EINVAL);
@@ -944,11 +944,10 @@ static inline void nand_op_trace(const char *prefix,
  *		 This method replaces chip->legacy.cmdfunc(),
  *		 chip->legacy.{read,write}_{buf,byte,word}(),
  *		 chip->legacy.dev_ready() and chip->legacy.waifunc().
- * @setup_data_interface: setup the data interface and timing. If
- *			  chipnr is set to %NAND_DATA_IFACE_CHECK_ONLY this
- *			  means the configuration should not be applied but
- *			  only checked.
- *			  This hook is optional.
+ * @setup_interface: setup the data interface and timing. If chipnr is set to
+ *		     %NAND_DATA_IFACE_CHECK_ONLY this means the configuration
+ *		     should not be applied but only checked.
+ *		     This hook is optional.
  */
 struct nand_controller_ops {
 	int (*attach_chip)(struct nand_chip *chip);
@@ -956,8 +955,8 @@ struct nand_controller_ops {
 	int (*exec_op)(struct nand_chip *chip,
 		       const struct nand_operation *op,
 		       bool check_only);
-	int (*setup_data_interface)(struct nand_chip *chip, int chipnr,
-				    const struct nand_data_interface *conf);
+	int (*setup_interface)(struct nand_chip *chip, int chipnr,
+			       const struct nand_interface_config *conf);
 };
 
 /**
@@ -1028,140 +1027,138 @@ struct nand_legacy {
 };
 
 /**
- * struct nand_chip - NAND Private Flash Chip Data
- * @base:		Inherit from the generic NAND device
- * @legacy:		All legacy fields/hooks. If you develop a new driver,
- *			don't even try to use any of these fields/hooks, and if
- *			you're modifying an existing driver that is using those
- *			fields/hooks, you should consider reworking the driver
- *			avoid using them.
- * @setup_read_retry:	[FLASHSPECIFIC] flash (vendor) specific function for
- *			setting the read-retry mode. Mostly needed for MLC NAND.
- * @ecc:		[BOARDSPECIFIC] ECC control structure
- * @buf_align:		minimum buffer alignment required by a platform
- * @oob_poi:		"poison value buffer," used for laying out OOB data
- *			before writing
- * @page_shift:		[INTERN] number of address bits in a page (column
- *			address bits).
- * @phys_erase_shift:	[INTERN] number of address bits in a physical eraseblock
- * @bbt_erase_shift:	[INTERN] number of address bits in a bbt entry
- * @chip_shift:		[INTERN] number of address bits in one chip
- * @options:		[BOARDSPECIFIC] various chip options. They can partly
- *			be set to inform nand_scan about special functionality.
- *			See the defines for further explanation.
- * @bbt_options:	[INTERN] bad block specific options. All options used
- *			here must come from bbm.h. By default, these options
- *			will be copied to the appropriate nand_bbt_descr's.
- * @badblockpos:	[INTERN] position of the bad block marker in the oob
- *			area.
- * @badblockbits:	[INTERN] minimum number of set bits in a good block's
- *			bad block marker position; i.e., BBM == 11110111b is
- *			not bad when badblockbits == 7
- * @onfi_timing_mode_default: [INTERN] default ONFI timing mode. This field is
- *			      set to the actually used ONFI mode if the chip is
- *			      ONFI compliant or deduced from the datasheet if
- *			      the NAND chip is not ONFI compliant.
- * @pagemask:		[INTERN] page number mask = number of (pages / chip) - 1
- * @data_buf:		[INTERN] buffer for data, size is (page size + oobsize).
- * @pagecache:		Structure containing page cache related fields
- * @pagecache.bitflips:	Number of bitflips of the cached page
- * @pagecache.page:	Page number currently in the cache. -1 means no page is
- *			currently cached
- * @subpagesize:	[INTERN] holds the subpagesize
- * @id:			[INTERN] holds NAND ID
- * @parameters:		[INTERN] holds generic parameters under an easily
- *			readable form.
- * @data_interface:	[INTERN] NAND interface timing information
- * @cur_cs:		currently selected target. -1 means no target selected,
- *			otherwise we should always have cur_cs >= 0 &&
- *			cur_cs < nanddev_ntargets(). NAND Controller drivers
- *			should not modify this value, but they're allowed to
- *			read it.
- * @read_retries:	[INTERN] the number of read retry modes supported
- * @lock:		lock protecting the suspended field. Also used to
- *			serialize accesses to the NAND device.
- * @suspended:		set to 1 when the device is suspended, 0 when it's not.
- * @suspend:		[REPLACEABLE] specific NAND device suspend operation
- * @resume:		[REPLACEABLE] specific NAND device resume operation
- * @bbt:		[INTERN] bad block table pointer
- * @bbt_td:		[REPLACEABLE] bad block table descriptor for flash
- *			lookup.
- * @bbt_md:		[REPLACEABLE] bad block table mirror descriptor
- * @badblock_pattern:	[REPLACEABLE] bad block scan pattern used for initial
- *			bad block scan.
- * @controller:		[REPLACEABLE] a pointer to a hardware controller
- *			structure which is shared among multiple independent
- *			devices.
- * @priv:		[OPTIONAL] pointer to private chip data
- * @manufacturer:	[INTERN] Contains manufacturer information
- * @manufacturer.desc:	[INTERN] Contains manufacturer's description
- * @manufacturer.priv:	[INTERN] Contains manufacturer private information
- * @lock_area:		[REPLACEABLE] specific NAND chip lock operation
- * @unlock_area:	[REPLACEABLE] specific NAND chip unlock operation
+ * struct nand_chip_ops - NAND chip operations
+ * @suspend: Suspend operation
+ * @resume: Resume operation
+ * @lock_area: Lock operation
+ * @unlock_area: Unlock operation
+ * @setup_read_retry: Set the read-retry mode (mostly needed for MLC NANDs)
+ * @choose_interface_config: Choose the best interface configuration
+ */
+struct nand_chip_ops {
+	int (*suspend)(struct nand_chip *chip);
+	void (*resume)(struct nand_chip *chip);
+	int (*lock_area)(struct nand_chip *chip, loff_t ofs, uint64_t len);
+	int (*unlock_area)(struct nand_chip *chip, loff_t ofs, uint64_t len);
+	int (*setup_read_retry)(struct nand_chip *chip, int retry_mode);
+	int (*choose_interface_config)(struct nand_chip *chip,
+				       struct nand_interface_config *iface);
+};
+
+/**
+ * struct nand_manufacturer - NAND manufacturer structure
+ * @desc: The manufacturer description
+ * @priv: Private information for the manufacturer driver
  */
+struct nand_manufacturer {
+	const struct nand_manufacturer_desc *desc;
+	void *priv;
+};
 
+/**
+ * struct nand_chip - NAND Private Flash Chip Data
+ * @base: Inherit from the generic NAND device
+ * @id: Holds NAND ID
+ * @parameters: Holds generic parameters under an easily readable form
+ * @manufacturer: Manufacturer information
+ * @ops: NAND chip operations
+ * @legacy: All legacy fields/hooks. If you develop a new driver, don't even try
+ *          to use any of these fields/hooks, and if you're modifying an
+ *          existing driver that is using those fields/hooks, you should
+ *          consider reworking the driver and avoid using them.
+ * @options: Various chip options. They can partly be set to inform nand_scan
+ *           about special functionality. See the defines for further
+ *           explanation.
+ * @current_interface_config: The currently used NAND interface configuration
+ * @best_interface_config: The best NAND interface configuration which fits both
+ *                         the NAND chip and NAND controller constraints. If
+ *                         unset, the default reset interface configuration must
+ *                         be used.
+ * @bbt_erase_shift: Number of address bits in a bbt entry
+ * @bbt_options: Bad block table specific options. All options used here must
+ *               come from bbm.h. By default, these options will be copied to
+ *               the appropriate nand_bbt_descr's.
+ * @badblockpos: Bad block marker position in the oob area
+ * @badblockbits: Minimum number of set bits in a good block's bad block marker
+ *                position; i.e., BBM = 11110111b is good when badblockbits = 7
+ * @bbt_td: Bad block table descriptor for flash lookup
+ * @bbt_md: Bad block table mirror descriptor
+ * @badblock_pattern: Bad block scan pattern used for initial bad block scan
+ * @bbt: Bad block table pointer
+ * @page_shift: Number of address bits in a page (column address bits)
+ * @phys_erase_shift: Number of address bits in a physical eraseblock
+ * @chip_shift: Number of address bits in one chip
+ * @pagemask: Page number mask = number of (pages / chip) - 1
+ * @subpagesize: Holds the subpagesize
+ * @data_buf: Buffer for data, size is (page size + oobsize)
+ * @oob_poi: pointer on the OOB area covered by data_buf
+ * @pagecache: Structure containing page cache related fields
+ * @pagecache.bitflips: Number of bitflips of the cached page
+ * @pagecache.page: Page number currently in the cache. -1 means no page is
+ *                  currently cached
+ * @buf_align: Minimum buffer alignment required by a platform
+ * @lock: Lock protecting the suspended field. Also used to serialize accesses
+ *        to the NAND device
+ * @suspended: Set to 1 when the device is suspended, 0 when it's not
+ * @cur_cs: Currently selected target. -1 means no target selected, otherwise we
+ *          should always have cur_cs >= 0 && cur_cs < nanddev_ntargets().
+ *          NAND Controller drivers should not modify this value, but they're
+ *          allowed to read it.
+ * @read_retries: The number of read retry modes supported
+ * @controller: The hardware controller	structure which is shared among multiple
+ *              independent devices
+ * @ecc: The ECC controller structure
+ * @priv: Chip private data
+ */
 struct nand_chip {
 	struct nand_device base;
-
+	struct nand_id id;
+	struct nand_parameters parameters;
+	struct nand_manufacturer manufacturer;
+	struct nand_chip_ops ops;
 	struct nand_legacy legacy;
+	unsigned int options;
 
-	int (*setup_read_retry)(struct nand_chip *chip, int retry_mode);
+	/* Data interface */
+	const struct nand_interface_config *current_interface_config;
+	struct nand_interface_config *best_interface_config;
 
-	unsigned int options;
+	/* Bad block information */
+	unsigned int bbt_erase_shift;
 	unsigned int bbt_options;
+	unsigned int badblockpos;
+	unsigned int badblockbits;
+	struct nand_bbt_descr *bbt_td;
+	struct nand_bbt_descr *bbt_md;
+	struct nand_bbt_descr *badblock_pattern;
+	u8 *bbt;
 
-	int page_shift;
-	int phys_erase_shift;
-	int bbt_erase_shift;
-	int chip_shift;
-	int pagemask;
-	u8 *data_buf;
+	/* Device internal layout */
+	unsigned int page_shift;
+	unsigned int phys_erase_shift;
+	unsigned int chip_shift;
+	unsigned int pagemask;
+	unsigned int subpagesize;
 
+	/* Buffers */
+	u8 *data_buf;
+	u8 *oob_poi;
 	struct {
 		unsigned int bitflips;
 		int page;
 	} pagecache;
+	unsigned long buf_align;
 
-	int subpagesize;
-	int onfi_timing_mode_default;
-	unsigned int badblockpos;
-	int badblockbits;
-
-	struct nand_id id;
-	struct nand_parameters parameters;
-
-	struct nand_data_interface data_interface;
-
-	int cur_cs;
-
-	int read_retries;
-
+	/* Internals */
 	struct mutex lock;
 	unsigned int suspended : 1;
-	int (*suspend)(struct nand_chip *chip);
-	void (*resume)(struct nand_chip *chip);
+	int cur_cs;
+	int read_retries;
 
-	uint8_t *oob_poi;
+	/* Externals */
 	struct nand_controller *controller;
-
 	struct nand_ecc_ctrl ecc;
-	unsigned long buf_align;
-
-	uint8_t *bbt;
-	struct nand_bbt_descr *bbt_td;
-	struct nand_bbt_descr *bbt_md;
-
-	struct nand_bbt_descr *badblock_pattern;
-
 	void *priv;
-
-	struct {
-		const struct nand_manufacturer *desc;
-		void *priv;
-	} manufacturer;
-
-	int (*lock_area)(struct nand_chip *chip, loff_t ofs, uint64_t len);
-	int (*unlock_area)(struct nand_chip *chip, loff_t ofs, uint64_t len);
 };
 
 extern const struct mtd_ooblayout_ops nand_ooblayout_sp_ops;
@@ -1209,6 +1206,17 @@ static inline struct device_node *nand_get_flash_node(struct nand_chip *chip)
 	return mtd_get_of_node(nand_to_mtd(chip));
 }
 
+/**
+ * nand_get_interface_config - Retrieve the current interface configuration
+ *                             of a NAND chip
+ * @chip: The NAND chip
+ */
+static inline const struct nand_interface_config *
+nand_get_interface_config(struct nand_chip *chip)
+{
+	return chip->current_interface_config;
+}
+
 /*
  * A helper for defining older NAND chips where the second ID byte fully
  * defined the chip, including the geometry (chip size, eraseblock size, page
@@ -1261,10 +1269,6 @@ static inline struct device_node *nand_get_flash_node(struct nand_chip *chip)
  *               @ecc_step_ds in nand_chip{}, also from the datasheet.
  *               For example, the "4bit ECC for each 512Byte" can be set with
  *               NAND_ECC_INFO(4, 512).
- * @onfi_timing_mode_default: the default ONFI timing mode entered after a NAND
- *			      reset. Should be deduced from timings described
- *			      in the datasheet.
- *
  */
 struct nand_flash_dev {
 	char *name;
@@ -1285,7 +1289,6 @@ struct nand_flash_dev {
 		uint16_t strength_ds;
 		uint16_t step_ds;
 	} ecc;
-	int onfi_timing_mode_default;
 };
 
 int nand_create_bbt(struct nand_chip *chip);
diff --git a/include/linux/mtd/spinand.h b/include/linux/mtd/spinand.h
index 1077c45721ff..7b78c4ba9b3e 100644
--- a/include/linux/mtd/spinand.h
+++ b/include/linux/mtd/spinand.h
@@ -309,7 +309,7 @@ struct spinand_info {
 	struct spinand_devid devid;
 	u32 flags;
 	struct nand_memory_organization memorg;
-	struct nand_ecc_req eccreq;
+	struct nand_ecc_props eccreq;
 	struct spinand_ecc_info eccinfo;
 	struct {
 		const struct spinand_op_variants *read_cache;
diff --git a/include/uapi/mtd/mtd-abi.h b/include/uapi/mtd/mtd-abi.h
index 4b48fbf7d343..65b9db936557 100644
--- a/include/uapi/mtd/mtd-abi.h
+++ b/include/uapi/mtd/mtd-abi.h
@@ -262,7 +262,7 @@ struct mtd_ecc_stats {
  * @MTD_FILE_MODE_OTP_USER:	OTP enabled in user mode
  * @MTD_FILE_MODE_RAW:		OTP disabled, ECC disabled
  *
- * These modes can be set via ioctl(MTDFILEMODE). The mode mode will be retained
+ * These modes can be set via ioctl(MTDFILEMODE). The mode will be retained
  * separately for each open file descriptor.
  *
  * Note: %MTD_FILE_MODE_RAW provides the same functionality as %MTD_OPS_RAW -